Search Results

Search found 8190 results on 328 pages for 'switch'.

Page 169/328 | < Previous Page | 165 166 167 168 169 170 171 172 173 174 175 176  | Next Page >

• Uploading to YouTube makes all browser tabs and devices disconnect

  - by fabsenet

  Whenever I upload a video to YouTube all other browser tabs behave like there is no connection at all. It even affects my phone and other computers on the network therefor I think it has to do with my router. When the upload is done everything works normally again. I never observed this behavior with any other upload. My router is a Fritz!Box 7390 and my uploading PC is connected through a 1000mb/s switch (wired) to the router. Uploading through another browser does not change anything. I understand that other sites become slow as the network resources are limited, but stopping altogether feels wrong. speed.io measures for my internet connection: 40.894 Kbit/s down, 2.685 Kbit/s up, 29 ms ping, 2.048 con/m connects

  Read the article

• If the WiFi switched on, should it disable the ethernet? [closed]

  - by Peter Stuart

  My friend having problems with her laptop and I am trying to help her via SMS. She can't get her laptop connected to the internet via the Ethernet connection and there is no WiFi in the area. Could it be because her WiFi is switch on, she is using an acer aspire. If she manually switches it off could that allow the ethernet connecttion to work? Or is it a missing driver? The cable works fine as her someone else tried it. Thanks Peter

  Read the article

• HP Virtual Connect and VLAN Tagging

  - by JaapL

  We have a c7000 chasis with the ability to have 8 uplinks per ESX host. Only 6 are currenlty active. I have a Virtual Switch with multiple vlan port groups and all the VMs are working fine. Recently we've been asked to setup network load balancing for one of our VMs, so we had our Virtual Connect engineer activate the last two uplinks. We then created a new vSwitch and added the two new uplinks to this vSwitch. We then moved the VM to this new vSwitch, but we get no connectivity. What could be the issue? We also added the appropriate VLAN ID. The VConnect engineer says everything is configured correctly and networking TEAM says the appropriate trunking is setup, so we are at a loss...

  Read the article

• Windows 7 strange boot issue

  - by JL

  Recently I installed an SSD drive, its now my primary boot drive (OCZ Vertex Turbo 60GB). I'm running Win 7 (64bit). Now I am not sure exactly where the fault lies, but when I do a restart from within Windows, the computer will boot and enter into the loading windows portion, however won't progress beyond there. My solution is to manually hit the reset switch, and then when it boots it enters into a windows menu that offers a start up repair or start windows normally. I select start windows normally, and then it boots fine. I am not entirely sure why I can't just restart the computer from windows normally though. The SSD drive works perfectly, and not even sure if it is the cause to this problem. Any ideas on this?

  Read the article

• Disable CTRL + ALT + [LETTER] to produce accented variations

  - by Barney

  After an unknown config change, CTRL + ALT + [LETTER] has started producing common accented versions of [LETTER]. I'm not a big fan of this arrangement, seeing as I've memorized all my favourite ALT + [NUMPAD SEQUENCE] references and was used to using CTRL + ALT + [LETTER] for various other application-specific commands in my text editor. The prominent result from my searching suggests that this has something to do with a switch to an 'international keyboard', and says this can be removed in the control panel or toggled by hitting ALT + SHIFT, but I can't get my system to confirm this, and the solutions (or close approximations thereof) don't work. Specifically, I've been to Control Panel\Clock, Language, and Region\Language\Advanced settings and switched the override for default input method from 'language list' to English and I've been to Control Panel\Clock, Language, and Region\Language\Language options and made sure that I only have my one input method (UK). Other than that I'm not quite sure where to look. Any ideas?

  Read the article

• basic help for Nat configuration needed

  - by Klaes S.

  I have a server with a IP 1.0.0.5/24. This is the main IP address of the server, and now I have two other IP addresses for the server, they are 1.0.2.30/24 and 1.0.2.31/24. I want to make a VirtualBox running another OS accessible through the Internet, and only allow the specified IP to reach the virtual box. I'm new to iptables and therefore I need some basic help and getting started information about this. The hosting provider does not allow more than on MAC address per switch port, which means that I'm not able to make bridge as far as I know. Futhermore I want the host, to reject the extra IPs so its only the VirtualBox / virtual machine that accepts the request's on the extra IPS.

  Read the article

• Prioritize file sharing performance in Windows Server 2008

  - by cmbrnt

  I've got a server running Windows Server 2008, and use it mainly for sharing files throughout the domain from a number of disks. It's running on VMware ESXi 4.0, in case that matters. My problem is that when I log in to the server to check user permissions etc, the access speed the files on the remote disks almost grinds to a halt. I havn't been able to measure the speeds, but I would guess it slows down to about 100kB/s as soon as I log in. This is on a gigabit network and the problems are equal for all users, even the ones connected to the same switch as the server. I've assigned 2 GB RAM to the server, and reserved it 1,5Ghz processor power. I don't have to do anything special on the server for this halt to occur. How can I make sure file sharing is prioritized on the server, so no matter what applications I'm using it will always make sure file sharing works properly? Could this be a VMware issue?

  Read the article

• Binding backward-kill-word to Ctrl+w

  - by nocturnal

  I'm trying to switch from prolonged use of Tcsh to recent exploration of Bash. I've managed to port over all my favorite features, except for Ctrl+w which treats spaces and slashes as word boundaries, most likely backward-kill-word. In Bash however readline deletes all the way to the first space, deleting all slashes between. I've tried many various combinations of \C-w: backward-kill-word in both .inputrc and .bashrc using bind but I can't get it to work the way I want. Funny enough, through Putty from Windows at work I can use Alt+Backspace, which also the manual says is the default binding, to produce the exact behavior I want. But in Terminal.app on my Macs at home this does not work. Same goes for any FreeBSD or Linux server I happen to be logged into from Terminal.app. So I turn to superuser for help.

  Read the article

• Amazon EC2 Sign In

  - by Barry

  When I change the home directory of my Amazon EC2 instance from /home/ubuntu to /home/ubuntu/folder in the /etc/passwd file, I am no longer able to access the instance using my existing keypair. Once I switch it back to the original directory I have no problems and can log into my instance as normal. I have checked the permissions on the new folder and they are drwxr-xr-x, which is the same the /home/ubuntu folder. I have a number of instances running at the minute and because of this change I have no way of logging back into them to rectify the situation. Does anyone have an idea what is going on? Thanks in advance

  Read the article

• Moving software RAID to Linux

  - by terman

  I'm using a RAID 1 (mirrored pair) configuration in my Media Center/ NAS system. Currently it's running Windows 8 (yeah, big mistake I know) and I'm regretting it (did it for the games, not worth it). Currently I'm having two software RAID 1s (3TB + 2TB) configured with Storage Spaces and unfortunately formatted with NTFS. Now I would like to switch to Fedora (or maybe Ubuntu if there are advantages) for good. Is there a way that I could continue using the disks as they are without the need to format them with ext or something? I'm glad for every tip. Oh, the system disk is of cause not in a raid configuration.

  Read the article

• Mac OS X change IP configuration automatically by location (by Wifi network)?

  - by Seppo Sade

  Can Mac OS X be setup to automatically configure its Airport interface with a static IP address when connected to a Wifi network with a certain name, and on all other Wifi networks use DHCP? Currently I'm using the "Locations" feature of the "Network" section in System Preferences to manually switch between two IP address setups. I have a "my static IP" setup, and a default "DHCP" setup. However this requires entering System Preferences to change the Location drop-down each time when switching locations. Can this be automated? Preferably this would be done without third-party software.

  Read the article

• Why is the System process listening on Port 443?

  - by ClearsTheScreen

  I am having problems starting my apache server, because port 443 is already in use. It turns out, the system process (PID 4) uses the port 443. I don't have IIS installed, the services.msc shows (predicatbly) no Exchange server running, nor WWW-Services, nor IIS. I have no idea how to find out what service uses that port short of just disabling each service one after the other, and I am not even sure that would help. I would be grateful if someone could point me towards how I can get my SSL port back, thank you :) P.S.: Of course "just switch apache to another port for SSL" would solve the problem of not being able to start apache. But I'd still like to know what is so insistent about hogging port 443. :)

  Read the article

• Is there a software in windows that enables you to boot from a specific partition?

  - by Tono Nam

  I use acronis true image to mount images to my primary partition and it works great. lets say I have 3 partitions on my hard disk and all of them each is 600 GB. In the 3rd partition I keep files (documents, pictures etc), on the first partition is my primary partition where the operating system runs (windows 7). And in the 2nd partition is empty. I have an image of my primary partition and I save that image in my 3rd partition (50 GB is the size of the image so it fits in the partition number 3) and in an external hard drive. I know it is possible to install a new operating system in partition 2 such as windows xp but the only problem is that once I install that how could I tell the computer to boot from partition 1? is there a way to switch back and forth just like it's possible in the mac?

  Read the article

• Audio Line-In on Ubuntu/Linux Mint

  - by hahuang65

  I'm currently on Windows, and want to switch to Linux, but some hardware issues are preventing me. Mainly, I have a sound card that supports Line-In. On Windows, anything I plug into the line-in gets outputted to the speakers. However, when I installed Linux, because there is not a control application that comes with the driver, I have no idea how to set this up. I tried going to the sound settings and it doesn't seem to be there. I also want to configure it for 2.1 sound, and do not know how to do that... Anyone here done it before? Thanks in advance for the help!

  Read the article

• Bsplayer - load audio tracks from external files

  - by torran

  I have a movie file: Video ID : 1 Format : AVC Format/Info : Advanced Video Codec Format profile : [email protected] Format settings, CABAC : Yes Format settings, ReFrames : 5 frames Muxing mode : Container [email protected] Codec ID : V_MPEG4/ISO/AVC Duration : 54mn 13s Bit rate : 3 380 Kbps Nominal bit rate : 3 459 Kbps Width : 1 280 pixels Height : 720 pixels Display aspect ratio : 16:9 Frame rate : 23.976 fps Resolution : 8 bits Colorimetry : 4:2:0 Scan type : Progressive Bits/(Pixel*Frame) : 0.153 Stream size : 1.28 GiB (88%) Writing library : x264 core 88 r1471 1144615 Audio ID : 2 Format : AC-3 Format/Info : Audio Coding 3 Codec ID : A_AC3 Duration : 54mn 16s Bit rate mode : Constant Bit rate : 384 Kbps Channel(s) : 6 channels Channel positions : Front: L C R, Side: L R, LFE Sampling rate : 48.0 KHz Stream size : 149 MiB (10%) and additional audio files in same folder: .mp3 and .ac3. How can I load them with bsplayer? Right click-audio-audio streams is empty. If i open the movie with media players classic I can switch audio files.

  Read the article

• Automatically changing a power profile when a laptop (un)docks?

  - by Dan

  I'm looking for a way to automatically change what happens when I close my laptop's lid depending on if it's in its docking station or not. In an idea world, the on-close behavior would be nothing (when docked) and sleep (when un-docked), but there only seems to be options for behavior when plugged-in and when on battery (when it's plugged in but not docked, I'd like it to sleep when closed). My initial idea would be to create a new power profile with this behavior, but I can't find a way to have it switch when docked (or for the power system to take its docked status into account at all). Any idea?

  Read the article

• Tool to allow Kerberos Authenticated users to modify Firewall settings

  - by Lars Hanke

  I run a firewall on a central router. Recently, several users want to use Skype. Since firewalling Skype virtually means to switch the firewall off, I consider to allow users to temporarily punch holes for their system. Since the users have no accounts on the router, I consider using Kerberos for authentication and authorization. The router is a Debian Squeeze box, with minimal configuration, i.e. no web-server, database or similar gimmicks. Does anyone know an existing solution, which could be used for that purpose? Or does anybody know easy to use and well documented frameworks in say Perl, Python, C, C++, ... making the set-up of a Kerberos authenticated Client and Server application really simple?

  Read the article

• DVI monitor detected only on computer startup

  - by kamil

  I've recently connected a new monitor, LG M2252D-PZ, to a rather outdated computer with Windows XP and Radeon 9600. XP has SP3 installed, video drivers are the latest version back from the times the video card was still supported. My problem is that the monitor works fine only as long as I don't turn it off or switch it to a different input. When I turn it back on, it says "no signal". The key to the problem must be the DVI port, to which the new monitor is connected. The previous monitor was connected to the VGA output, and I've tested that the new one also works fine when connected to the analogue port. Apparently, the computer tests for the presence of a monitor on the DVI port only on startup. The question is, how do I change this?

  Read the article

• I have a 21TB array but only 16TB is visible from Windows

  - by Relentim

  CONTROLLER Raid Controller: 3Ware 9650SE-24M8 Disks: 21 x 1TB RAID5 Stripe 64KB WINDOWS OS: Windows Server 2003 SP2 32x Disk: Dynamic 19557.44GB Volume: Capacity 15832.19GB I guess my array must have a 4KB block size which is limiting it to 16TB. I think I would have to switch to a 64KB block size to be able to see a maximum of 256TB. Or create another unit on my controller to go above 16TB of storage. Unfortunately I have already added over 16TB, ideally I would like to shrink the array and reclaim the 5 disks that aren't doing anything. I don't think this is possible. More likely, can I change the block size so 20TB becomes visible in windows?

  Read the article

• What is the best Linux distro for a php web server? [on hold]

  - by benjisail

  We are planning to upgrade our hardware and at the same time we plan to reinstall all our web server from a fresh OS. Currently our web server is running on CentOS 4.7 on a dedicated server. We are using Apache, Mysql, PHP, SVN, FTP and all the needed tools for a web server managed through SSH. We plan to use a cloud server for the new web server. I don't know which Linux distro to take for this new server. Should I stay with Centos and just take the latest release 5.4 or should I switch to something else like a Debian base distro (Ubuntu Server)? The thing that I didn't like with CentOS was the none availability of the latest version of PHP and Apache on Yum. This make it harder to keep our webserver updated with the latest technologies... Thanks for your help!

  Read the article

• Internet sharing over LAN on Windows Server 2012

  - by USER

  I have a DSL modem connected to a server (ON NIC1) running Windows Server 2012 and 7 computers (running Windows 7 32-Bit) connected to a server though a network switch (ON NIC2). I shared the internet connection from the server through DHCP so I am able to access the internet from those 7 computers, but I am unable to: Access Google.com Activate Windows Update Windows An error is arising that says UNABLE TO ACTIVATE WINDOWS Activation Error Code: 0x80072EE2 Firewall and Anti-Virus are off on both the Server and the Clients. Is there is any additional setting that I want to do?

  Read the article

• Forbid links to open new tabs in Google Chrome

  - by Andrzej

  I'm looking for a solution to forbid links in Google Chrome to open new tabs (in most cases it is a target="_blank" issue). So, I want all links to open pages in currently active tab, not in new tab. I tried a wide range of addons (for ex. "Death to target=_blank") and greasemonkey scripts that are supposed to remove target=_blank attribute but none of them worked. It is extremally anoying when I want to switch between accounts in GMail or navigate from GMail to GDrive. I always get the new tab opened and I need to close last tab manually.

  Read the article

• Snort monitoring of spanning interface

  - by aHunter

  I have configured a Cisco 3500 switch with a port SPAN and have my snort node (fedora 13) plugged into it. I am running snort as a daemon and have configured a rule to log all tcp traffic but I am only seeing traffic with a destination of the snort node. I know that the SPAN port is working and wanted to know if there is a specific option that I needed to start snort with in order for it to pickup all the traffic? Or is there something that I have missed here? Many thanks.

  Read the article

• tricks for speeding up tar while tarring up a huge directory of little files?

  - by Trevor Harrison

  I'm trying to tar up a directory that has about 3M tiny files in it. Tar is chugging along, but I'm thinking its going to take longer than I can wait. I'm wondering if telling tar to not store metadata (owner, group, perms) would reduce the churn on reading and re-reading this huge directory and maybe speed things up, and if there is a tar switch that does this. My initial perusal of the man page only gets me something like --no-xattrs, which looks like a start, but I was hoping someone had some specific knowledge.

  Read the article

• Excel - Chart that sums the values in multiple rows for each series

  - by Chaulky

  Suppose I have a spread sheet that looks something like this... Now, I'd like to create a column chart that has 3 series, one for each country. Then, I want series for each category, but I want to plot the total, not each individual order total. So, something like this (excuse the horrible artwork)... The data label placement isn't all the important, the key is that for each Category (Bikes and Clothes) I chart the total for each country, not individual values from the "Order Total" column. Is this possible? Is it possible to do the same idea, but to switch Country and Category around?

  Read the article

< Previous Page | 165 166 167 168 169 170 171 172 173 174 175 176  | Next Page >