Search Results

Search found 14653 results on 587 pages for 'disk cache'.

Page 171/587 | < Previous Page | 167 168 169 170 171 172 173 174 175 176 177 178  | Next Page >

• e2fsck / resize2fs problems

  - by BlakBat

  I've got 6 drives (each 1.5T, all same model and firmware revision) that are part of a RAID5 array. The RAID5 makes a LVM volume group and a logical group. The latter contains only one ext3 partition. I've recently ran: e2fsck -f /dev/vg03/lv01 && resize2fs -M /dev/vg03/lv01 which exited without an error. Now when I try to mount /dev/vg03/lv01 I get: EXT3-fs error (device dm-0): ext3_check_descriptors: Block bitmap for group 30533 not in group (block 1000532368)! EXT3-fs: group descriptors corrupted! How do I get out of this predicament? This is all the info I can currently give you: fdisk -l /dev/sd[cdefgh] shows (correctly) that they are "Linux raid autodetect" but fdisk now shows: fdisk -l /dev/md0 Disk /dev/md0: 7501.5 GB, 7501495664640 bytes ... Disk identifier: 0x00000000 Disk /dev/md0 doesn't contain a valid partition table (instead of a LVM type partition) fdisk -l /dev/vg03/lv01 Disk /dev/vg03/lv01: 7501.5 GB, 7501491732480 bytes ... Disk identifier: 0x00000000 Disk /dev/vg03/lv01 doesn't contain a valid partition table (instead of a ext3 type partition) I've tried: e2fsck -fy /dev/vg03/lv01 e2fsck 1.41.12 (17-May-2010) e2fsck: Group descriptors look bad... trying backup blocks... Block bitmap for group 30533 is not in group. (block 1000532368) Relocate? yes Inode bitmap for group 30533 is not in group. (block 1000532369) Relocate? yes Pass 1: Checking inodes, blocks, and sizes Relocating group 30533's block bitmap to 1000524246... Error allocating 1 contiguous block(s) in block group 30533 for inode bitmap: Could not allocate block in ext2 filesystem e2fsck: aborted Extra information I can give you: cat /proc/mdstat Personalities : [linear] [multipath] [raid0] [raid1] [raid6] [raid5] [raid4] [raid10] md0 : active (auto-read-only) raid5 sdg1[0] sdh1[5] sdf1[4] sde1[3] sdc1[2] sdd1[1] 7325679360 blocks level 5, 128k chunk, algorithm 2 [6/6] [UUUUUU] bitmap: 1/175 pages [4KB], 4096KB chunk unused devices: Lastly, all smartctl tests (short and extendend) showed no errors on any of the disks. Should I try to resize2fs to grow /dev/vg03/lv01 and redo a e2fsck ? Should I cfdisk /dev/md0 and /dev/vg03/lv01 back to their real types? Thanks in advance for all and any help. 2011-09-20 UPDATE I issued the following commands and was able to remount the partition, but by viewing the size (df) of before and after, it seems that 1Tb of data have gone missing. By checking the MD5SUMS (from an old backup) of some files with the "same" files from the remounted partition, some errors have been detected. Commands issued to remount the partition were: dumpe2fs /dev/vg03/lv01 Block count: 1000491435<br /> Block size: 4096<br /> tune2fs -O ^has_journal /dev/vg03/lv01 resize2fs -p /dev/vg03/lv01 dumpe2fs /dev/vg03/lv01 Block count: 1831418880<br /> Block size: 4096<br /> mount -o ro,noatime /dev/vg03/lv01 /mnt/raid OK... but files have been damaged / gone missing.

  Read the article

• Doctrine 2 Cannot find entites

  - by Flyn San

  I'm using Kohana 3 and have a /doctrine/Entites folder with my entities inside. When executing the code $product = Doctrine::em()->find('Entities\Product', 1); in my controller, I get the error class_parents(): Class Entities\Product does not exist and could not be loaded Below is the Controller (classes/controller/welcome.php): <?php class Controller_Welcome extends Controller { public function action_index() { $prod = Doctrine::em()->find('Entities\Product', 1); } } Below is the Entity (/doctrine/Entities/Product.php): <?php /** * @Entity * @Table{name="products"} */ class Product { /** @Id @Column{type="integer"} */ private $id; /** @Column(type="string", length="255") */ private $name; public function getId() { return $this->id; } public function setId($id) { $this->id = intval($id); } public function getName() { return $this->name; } public function setName($name) { $this->name = $name; } } Below is the Doctrine module bootstrap file (/modules/doctrine/init.php): class Doctrine { private static $_instance = null; private $_application_mode = 'development'; private $_em = null; public static function em() { if ( self::$_instance === null ) self::$_instance = new Doctrine(); return self::$_instance->_em; } public function __construct() { require __DIR__.'/classes/doctrine/Doctrine/Common/ClassLoader.php'; $classLoader = new \Doctrine\Common\ClassLoader('Doctrine', __DIR__.'/classes/doctrine'); $classLoader->register(); $classLoader = new \Doctrine\Common\ClassLoader('Symfony', __DIR__.'/classes/doctrine/Doctrine'); $classLoader->register(); $classLoader = new \Doctrine\Common\ClassLoader('Entities', APPPATH.'doctrine'); $classLoader->register(); //Set up caching method $cache = $this->_application_mode == 'development' ? new \Doctrine\Common\Cache\ArrayCache : new \Doctrine\Common\Cache\ApcCache; $config = new Configuration; $config->setMetadataCacheImpl( $cache ); $driver = $config->newDefaultAnnotationDriver( APPPATH.'doctrine/Entities' ); $config->setMetadataDriverImpl( $driver ); $config->setQueryCacheImpl( $cache ); $config->setProxyDir( APPPATH.'doctrine/Proxies' ); $config->setProxyNamespace('Proxies'); $config->setAutoGenerateProxyClasses( $this->_application_mode == 'development' ); $dbconf = Kohana::config('database'); $dbconf = reset($dbconf); //Use the first database specified in the config $this->_em = EntityManager::create(array( 'dbname' => $dbconf['connection']['database'], 'user' => $dbconf['connection']['username'], 'password' => $dbconf['connection']['password'], 'host' => $dbconf['connection']['hostname'], 'driver' => 'pdo_mysql', ), $config); } } Any ideas what I've done wrong?

  Read the article

• Is it too early to start designing for Task Parallel Library?

  - by Joe Erickson

  I have been following the development of the .NET Task Parallel Library (TPL) with great interest since Microsoft first announced it. There is no doubt in my mind that we will eventually take advantage of TPL. What I am questioning is whether it makes sense to start taking advantage of TPL when Visual Studio 2010 and .NET 4.0 are released, or whether it makes sense to wait a while longer. Why Start Now? The .NET 4.0 Task Parallel Library appears to be well designed and some relatively simple tests demonstrate that it works well on today's multi-core CPUs. I have been very interested in the potential advantages of using multiple lightweight threads to speed up our software since buying my first quad processor Dell Poweredge 6400 about seven years ago. Experiments at that time indicated that it was not worth the effort, which I attributed largely to the overhead of moving data between each CPU's cache (there was no shared cache back then) and RAM. Competitive advantage - some of our customers can never get enough performance and there is no doubt that we can build a faster product using TPL today. It sounds fun. Yes, I realize that some developers would rather poke themselves in the eye with a sharp stick, but we really enjoy maximizing performance. Why Wait? Are today's Intel Nehalem CPUs representative of where we are going as multi-core support matures? You can purchase a Nehalem CPU with 4 cores which share a single level 3 cache today, and most likely a 6 core CPU sharing a single level 3 cache by the time Visual Studio 2010 / .NET 4.0 are released. Obviously, the number of cores will go up over time, but what about the architecture? As the number of cores goes up, will they still share a cache? One issue with Nehalem is the fact that, even though there is a very fast interconnect between the cores, they have non-uniform memory access (NUMA) which can lead to lower performance and less predictable results. Will future multi-core architectures be able to do away with NUMA? Similarly, will the .NET Task Parallel Library change as it matures, requiring modifications to code to fully take advantage of it? Limitations Our core engine is 100% C# and has to run without full trust, so we are limited to using .NET APIs.

  Read the article

• HTTP caching confusion

  - by Keith

  I'm not sure whether this is a server issue, or whether I'm failing to understand how HTTP caching really works. I have an ASP MVC application running on IIS7. There's a lot of static content as part of the site including lots of CSS, Javascript and image files. For these files I want the browser to cache them for at least a day - our .css, .js, .gif and .png files rarely change. My web.config goes like this: <system.webServer> <staticContent> <clientCache cacheControlMode="UseMaxAge" cacheControlMaxAge="1.00:00:00" /> </staticContent> </system.webServer> The problem I'm getting is that the browser (tested Chrome, IE8 and FX) doesn't seem to be caching the files as I'd expect. I've got the default settings (check for newer pages automatically in IE). On first visit the content downloads as expected HTTP/1.1 200 OK Cache-Control: max-age=86400 Content-Type: image/gif Last-Modified: Fri, 07 Aug 2009 09:55:15 GMT Accept-Ranges: bytes ETag: "3efeb2294517ca1:0" Server: Microsoft-IIS/7.0 X-Powered-By: ASP.NET Date: Mon, 07 Jun 2010 14:29:16 GMT Content-Length: 918 <content> I think that the Cache-Control: max-age=86400 should tell the browser not to request the page again for a day. Ok, so now the page is reloaded and the browser requests the image again. This time it gets an empty response with these headers: HTTP/1.1 304 Not Modified Cache-Control: max-age=86400 Last-Modified: Fri, 07 Aug 2009 09:55:15 GMT Accept-Ranges: bytes ETag: "3efeb2294517ca1:0" Server: Microsoft-IIS/7.0 X-Powered-By: ASP.NET Date: Mon, 07 Jun 2010 14:30:32 GMT So it looks like the browser has sent the ETag back (as a unique id for the resource), and the server's come back with a 304 Not Modified - telling the browser that it can use the previously downloaded file. It seems to me that would be correct for many caching situations, but here I don't want the extra round trip. I don't care if the image gets out of date when the file on the server changes. There are a lot of these files (even with sprite-maps and the like) and many of our clients have very slow networks. Each round trip to ping for that 304 status is taking about a 10th to a 5th of a second. Many also have IE6 which only has 2 HTTP connections at a time. The net result is that our application appears to be very slow for these clients with every page taking an extra couple of seconds to check that the static content hasn't changed. What response header am I missing that would cause the browser to aggressively cache the files? How would I set this in a .Net web.config for IIS7? Am I misunderstanding how HTTP caching works in the first place?

  Read the article

• Should I HttpCombine Google Jquery Hosted File?

  - by chobo2

  Hi I am using something called HttpCombiner: http://code.msdn.microsoft.com/HttpCombiner An HTTP handler that combines multiple CSS, Javascript or URL into one response for faster page load. It can combine, compress and cache response which results in faster page load and better scalability of web application It's a good practice to use many small Javascript and CSS files instead of one large Javascript/CSS file for better code maintainability, but bad in terms of website performance. Although you should write your Javascript code in small files and break large CSS files into small chunks but when browser requests those javascript and css files, it makes one Http request per file. Every Http Request results in a network roundtrip form your browser to the server and the delay in reaching the server and coming back to the browser is called latency. So, if you have four javascripts and three css files loaded by a page, you are wasting time in seven network roundtrips. Within USA, latency is average 70ms. So, you waste 7x70 = 490ms, about half a second of delay. Outside USA, average latency is around 200ms. So, that means 1400ms of waiting. Browser cannot show the page properly until Css and Javascripts are fully loaded. So, the more latency you have, the slower page loads. You can reduce the wait time by using a CDN. Read my previous blog post about using CDN. However, a better solution is to deliver multiple files over one request using an HttpHandler that combines several files and delivers as one output. So, instead of putting many or tag, you just put one and one tag, and point them to the HttpHandler. You tell the handler which files to combine and it delivers those files in one response. This saves browser from making many requests and eliminates the latency. This Http Handler reads the file names defined in a configuration and combines all those files and delivers as one response. It delivers the response as gzip compressed to save bandwidth. Moreover, it generates proper cache header to cache the response in browser cache, so that, browser does not request it again on future visit. Now I am wondering since it can handle adding links should I put in it the jquery file? The reason I am not sure is if it gets combined with my other files I think I might close the advantages of it being hosted on googles servers such as caching(my thinking is if it gets combined it will look different so even if a user has it in it's cache I am not sure if it will use the one for the cahce or not). So should I combine it or only the finals that I am using locally?

  Read the article

• Ajax gets nothing back from the php.

  - by ShaMun

  Jquery i dont have alert and firefox i dont have anything in return. The code was working before, database query have successfull records also. What i am missing??? Jquery ajax. $.ajax({ type : "POST", url : "include/add_edit_del.php?model=teksten_display", data : "oper=search&ids=" + _id , dataType: "json", success : function(msg){ alert(msg); } }); PHP case 'teksten_display': $id = $_REQUEST['ids']; $res = $_dclass-_query_sql( "select a,b,id,wat,c,d from tb1 where id='" . $id . "'" ); $_rows = array(); while ( $rows = mysql_fetch_array ($res) ) { $_rows = $rows; } //header('Cache-Control: no-cache, must-revalidate'); //header('Expires: Mon, 26 Jul 1997 05:00:00 GMT'); header('Content-type: application/json'); echo utf8_encode( json_encode($_rows) ) ; //echo json_encode($_rows); //var_dump($_rows); //print_r ($res); break; Firefox response/request header Date Sat, 24 Apr 2010 22:34:55 GMT Server Apache/2.2.3 (CentOS) X-Powered-By PHP/5.1.6 Expires Thu, 19 Nov 1981 08:52:00 GMT Cache-Control no-store, no-cache, must-revalidate, post-check=0, pre-check=0 Pragma no-cache Content-Length 0 Connection close Content-Type application/json Host www.xxxx.be User-Agent Mozilla/5.0 (X11; U; Linux i686; en-US; rv:1.9.1.9) Gecko/20100330 Fedora/3.5.9-2.fc12 Firefox/3.5.9 Accept application/json, text/javascript, */* Accept-Language en-us,en;q=0.5 Accept-Encoding gzip,deflate Accept-Charset ISO-8859-1,utf-8;q=0.7,*;q=0.7 Keep-Alive 300 Connection keep-alive Content-Type application/x-www-form-urlencoded; charset=UTF-8 X-Requested-With XMLHttpRequest Referer http://www.xxxx.be/xxxxx Content-Length 17 Cookie csdb=2; codb=5; csdbb=1; codca=1.4; csdca=3; PHPSESSID=benunvkpecqh3pmd8oep5b55t7; CAKEPHP=3t7hrlc89emvg1hfsc45gs2bl2

  Read the article

• Lighttpd + fastcgi + python (for django) slow on first request

  - by EagleOne

  I'm having a problem with a django website I host with lighttpd + fastcgi. It works great but it seems that the first request always takes up to 3seconds. Subsequent requests are much faster (<1s). I activated access logs in lighttpd in order to track the issue. But I'm kind of stuck. Here are logs where I 'lose' 4s (from 10:04:17 to 10:04:21): 2012-12-01 10:04:17: (mod_fastcgi.c.3636) handling it in mod_fastcgi 2012-12-01 10:04:17: (response.c.470) -- before doc_root 2012-12-01 10:04:17: (response.c.471) Doc-Root : /var/www 2012-12-01 10:04:17: (response.c.472) Rel-Path : /finderauto.fcgi 2012-12-01 10:04:17: (response.c.473) Path : 2012-12-01 10:04:17: (response.c.521) -- after doc_root 2012-12-01 10:04:17: (response.c.522) Doc-Root : /var/www 2012-12-01 10:04:17: (response.c.523) Rel-Path : /finderauto.fcgi 2012-12-01 10:04:17: (response.c.524) Path : /var/www/finderauto.fcgi 2012-12-01 10:04:17: (response.c.541) -- logical -> physical 2012-12-01 10:04:17: (response.c.542) Doc-Root : /var/www 2012-12-01 10:04:17: (response.c.543) Rel-Path : /finderauto.fcgi 2012-12-01 10:04:17: (response.c.544) Path : /var/www/finderauto.fcgi 2012-12-01 10:04:21: (response.c.128) Response-Header: HTTP/1.1 200 OK Last-Modified: Sat, 01 Dec 2012 09:04:21 GMT Expires: Sat, 01 Dec 2012 09:14:21 GMT Content-Type: text/html; charset=utf-8 Cache-Control: max-age=600 Transfer-Encoding: chunked Date: Sat, 01 Dec 2012 09:04:21 GMT Server: lighttpd/1.4.28 I guess that if there is a problem, it's whith my configuration. So here is the way I launch my django app: python manage.py runfcgi method=threaded host=127.0.0.1 port=3033 And here is my lighttpd conf: server.modules = ( "mod_access", "mod_alias", "mod_compress", "mod_redirect", "mod_rewrite", "mod_fastcgi", "mod_accesslog", ) server.document-root = "/var/www" server.upload-dirs = ( "/var/cache/lighttpd/uploads" ) server.errorlog = "/var/log/lighttpd/error.log" server.pid-file = "/var/run/lighttpd.pid" server.username = "www-data" server.groupname = "www-data" accesslog.filename = "/var/log/lighttpd/access.log" debug.log-request-header = "enable" debug.log-response-header = "enable" debug.log-file-not-found = "enable" debug.log-request-handling = "enable" debug.log-timeouts = "enable" debug.log-ssl-noise = "enable" debug.log-condition-cache-handling = "enable" debug.log-condition-handling = "enable" fastcgi.server = ( "/finderauto.fcgi" => ( "main" => ( # Use host / port instead of socket for TCP fastcgi "host" => "127.0.0.1", "port" => 3033, #"socket" => "/home/finderadmin/finderauto.sock", "check-local" => "disable", "fix-root-scriptname" => "enable", ) ), ) alias.url = ( "/media" => "/home/user/django/contrib/admin/media/", ) url.rewrite-once = ( "^(/media.*)$" => "$1", "^/favicon\.ico$" => "/media/favicon.ico", "^(/.*)$" => "/finderauto.fcgi$1", ) index-file.names = ( "index.php", "index.html", "index.htm", "default.htm", " index.lighttpd.html" ) url.access-deny = ( "~", ".inc" ) static-file.exclude-extensions = ( ".php", ".pl", ".fcgi" ) ## Use ipv6 if available #include_shell "/usr/share/lighttpd/use-ipv6.pl" dir-listing.encoding = "utf-8" server.dir-listing = "enable" compress.cache-dir = "/var/cache/lighttpd/compress/" compress.filetype = ( "application/x-javascript", "text/css", "text/html", "text/plain" ) include_shell "/usr/share/lighttpd/create-mime.assign.pl" include_shell "/usr/share/lighttpd/include-conf-enabled.pl" If any of you could help me finding out where I lose these 3 or 4 s. I would much appreciate. Thanks in advance!

  Read the article

• Unable to boot Windows 7 after installing Ubuntu

  - by Devendra

  I have Windows 7 on my machine and then installed Ubuntu 12.04 using a live CD. I can see both Windows 7 and Ubuntu in the grub menu, but when I select Windows 7 it shows a black screen for about 2 seconds and the returns to the Grub menu. But if I select Ubuntu it's working fine. This is the contents of the boot-repair log: Boot Info Script 0.61.full + Boot-Repair extra info [Boot-Info November 20th 2012] ============================= Boot Info Summary: =============================== => Grub2 (v2.00) is installed in the MBR of /dev/sda and looks at sector 1 of the same hard drive for core.img. core.img is at this location and looks in partition 1 for (,msdos6)/boot/grub. sda1: __________________________________________________________________________ File system: ntfs Boot sector type: Grub2 (v1.99-2.00) Boot sector info: Grub2 (v2.00) is installed in the boot sector of sda1 and looks at sector 388911128 of the same hard drive for core.img. core.img is at this location and looks in partition 1 for (,msdos6)/boot/grub. No errors found in the Boot Parameter Block. Operating System: Windows 7 Boot files: /bootmgr /Boot/BCD /Windows/System32/winload.exe sda2: __________________________________________________________________________ File system: ntfs Boot sector type: Windows Vista/7: NTFS Boot sector info: No errors found in the Boot Parameter Block. Operating System: Boot files: sda3: __________________________________________________________________________ File system: ntfs Boot sector type: Windows Vista/7: NTFS Boot sector info: No errors found in the Boot Parameter Block. Operating System: Boot files: sda4: __________________________________________________________________________ File system: Extended Partition Boot sector type: - Boot sector info: sda5: __________________________________________________________________________ File system: ntfs Boot sector type: Windows Vista/7: NTFS Boot sector info: According to the info in the boot sector, sda5 starts at sector 2048. Operating System: Boot files: sda6: __________________________________________________________________________ File system: ext4 Boot sector type: - Boot sector info: Operating System: Ubuntu 12.10 Boot files: /boot/grub/grub.cfg /etc/fstab /boot/grub/i386-pc/core.img sda7: __________________________________________________________________________ File system: swap Boot sector type: - Boot sector info: ============================ Drive/Partition Info: ============================= Drive: sda _____________________________________________________________________ Disk /dev/sda: 750.2 GB, 750156374016 bytes 255 heads, 63 sectors/track, 91201 cylinders, total 1465149168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 4096 bytes Partition Boot Start Sector End Sector # of Sectors Id System /dev/sda1 * 206,848 146,802,687 146,595,840 7 NTFS / exFAT / HPFS /dev/sda2 147,007,488 293,623,807 146,616,320 7 NTFS / exFAT / HPFS /dev/sda3 293,623,808 332,820,613 39,196,806 7 NTFS / exFAT / HPFS /dev/sda4 332,822,526 1,465,145,343 1,132,322,818 f W95 Extended (LBA) /dev/sda5 461,342,720 1,465,145,343 1,003,802,624 7 NTFS / exFAT / HPFS /dev/sda6 332,822,528 453,171,199 120,348,672 83 Linux /dev/sda7 453,173,248 461,338,623 8,165,376 82 Linux swap / Solaris "blkid" output: ________________________________________________________________ Device UUID TYPE LABEL /dev/sda1 F6AE2C13AE2BCB47 ntfs /dev/sda2 DC2273012272DFC6 ntfs /dev/sda3 1E76E43376E40D79 ntfs New Volume /dev/sda5 5ED60ACDD60AA57D ntfs /dev/sda6 9e70fd16-b48b-4f88-adcf-e443aef83124 ext4 /dev/sda7 52f3dd94-6be7-4a7b-a3ae-f43eb8810483 swap ================================ Mount points: ================================= Device Mount_Point Type Options /dev/sda6 / ext4 (rw,errors=remount-ro) =========================== sda6/boot/grub/grub.cfg: =========================== -------------------------------------------------------------------------------- # # DO NOT EDIT THIS FILE # # It is automatically generated by grub-mkconfig using templates # from /etc/grub.d and settings from /etc/default/grub # ### BEGIN /etc/grub.d/00_header ### if [ -s $prefix/grubenv ]; then set have_grubenv=true load_env fi set default="0" if [ x"${feature_menuentry_id}" = xy ]; then menuentry_id_option="--id" else menuentry_id_option="" fi export menuentry_id_option if [ "${prev_saved_entry}" ]; then set saved_entry="${prev_saved_entry}" save_env saved_entry set prev_saved_entry= save_env prev_saved_entry set boot_once=true fi function savedefault { if [ -z "${boot_once}" ]; then saved_entry="${chosen}" save_env saved_entry fi } function recordfail { set recordfail=1 if [ -n "${have_grubenv}" ]; then if [ -z "${boot_once}" ]; then save_env recordfail; fi; fi } function load_video { if [ x$feature_all_video_module = xy ]; then insmod all_video else insmod efi_gop insmod efi_uga insmod ieee1275_fb insmod vbe insmod vga insmod video_bochs insmod video_cirrus fi } if [ x$feature_default_font_path = xy ] ; then font=unicode else insmod part_msdos insmod ext2 set root='hd0,msdos6' if [ x$feature_platform_search_hint = xy ]; then search --no-floppy --fs-uuid --set=root --hint-bios=hd0,msdos6 --hint-efi=hd0,msdos6 --hint-baremetal=ahci0,msdos6 9e70fd16-b48b-4f88-adcf-e443aef83124 else search --no-floppy --fs-uuid --set=root 9e70fd16-b48b-4f88-adcf-e443aef83124 fi font="/usr/share/grub/unicode.pf2" fi if loadfont $font ; then set gfxmode=auto load_video insmod gfxterm set locale_dir=$prefix/locale set lang=en_IN insmod gettext fi terminal_output gfxterm if [ "${recordfail}" = 1 ]; then set timeout=10 else set timeout=10 fi ### END /etc/grub.d/00_header ### ### BEGIN /etc/grub.d/05_debian_theme ### set menu_color_normal=white/black set menu_color_highlight=black/light-gray if background_color 44,0,30; then clear fi ### END /etc/grub.d/05_debian_theme ### ### BEGIN /etc/grub.d/10_linux ### function gfxmode { set gfxpayload="${1}" if [ "${1}" = "keep" ]; then set vt_handoff=vt.handoff=7 else set vt_handoff= fi } if [ "${recordfail}" != 1 ]; then if [ -e ${prefix}/gfxblacklist.txt ]; then if hwmatch ${prefix}/gfxblacklist.txt 3; then if [ ${match} = 0 ]; then set linux_gfx_mode=keep else set linux_gfx_mode=text fi else set linux_gfx_mode=text fi else set linux_gfx_mode=keep fi else set linux_gfx_mode=text fi export linux_gfx_mode if [ "${linux_gfx_mode}" != "text" ]; then load_video; fi menuentry 'Ubuntu' --class ubuntu --class gnu-linux --class gnu --class os $menuentry_id_option 'gnulinux-simple-9e70fd16-b48b-4f88-adcf-e443aef83124' { recordfail gfxmode $linux_gfx_mode insmod gzio insmod part_msdos insmod ext2 set root='hd0,msdos6' if [ x$feature_platform_search_hint = xy ]; then search --no-floppy --fs-uuid --set=root --hint-bios=hd0,msdos6 --hint-efi=hd0,msdos6 --hint-baremetal=ahci0,msdos6 9e70fd16-b48b-4f88-adcf-e443aef83124 else search --no-floppy --fs-uuid --set=root 9e70fd16-b48b-4f88-adcf-e443aef83124 fi linux /boot/vmlinuz-3.5.0-17-generic root=UUID=9e70fd16-b48b-4f88-adcf-e443aef83124 ro quiet splash $vt_handoff initrd /boot/initrd.img-3.5.0-17-generic } submenu 'Advanced options for Ubuntu' $menuentry_id_option 'gnulinux-advanced-9e70fd16-b48b-4f88-adcf-e443aef83124' { menuentry 'Ubuntu, with Linux 3.5.0-17-generic' --class ubuntu --class gnu-linux --class gnu --class os $menuentry_id_option 'gnulinux-3.5.0-17-generic-advanced-9e70fd16-b48b-4f88-adcf-e443aef83124' { recordfail gfxmode $linux_gfx_mode insmod gzio insmod part_msdos insmod ext2 set root='hd0,msdos6' if [ x$feature_platform_search_hint = xy ]; then search --no-floppy --fs-uuid --set=root --hint-bios=hd0,msdos6 --hint-efi=hd0,msdos6 --hint-baremetal=ahci0,msdos6 9e70fd16-b48b-4f88-adcf-e443aef83124 else search --no-floppy --fs-uuid --set=root 9e70fd16-b48b-4f88-adcf-e443aef83124 fi echo 'Loading Linux 3.5.0-17-generic ...' linux /boot/vmlinuz-3.5.0-17-generic root=UUID=9e70fd16-b48b-4f88-adcf-e443aef83124 ro quiet splash $vt_handoff echo 'Loading initial ramdisk ...' initrd /boot/initrd.img-3.5.0-17-generic } menuentry 'Ubuntu, with Linux 3.5.0-17-generic (recovery mode)' --class ubuntu --class gnu-linux --class gnu --class os $menuentry_id_option 'gnulinux-3.5.0-17-generic-recovery-9e70fd16-b48b-4f88-adcf-e443aef83124' { recordfail insmod gzio insmod part_msdos insmod ext2 set root='hd0,msdos6' if [ x$feature_platform_search_hint = xy ]; then search --no-floppy --fs-uuid --set=root --hint-bios=hd0,msdos6 --hint-efi=hd0,msdos6 --hint-baremetal=ahci0,msdos6 9e70fd16-b48b-4f88-adcf-e443aef83124 else search --no-floppy --fs-uuid --set=root 9e70fd16-b48b-4f88-adcf-e443aef83124 fi echo 'Loading Linux 3.5.0-17-generic ...' linux /boot/vmlinuz-3.5.0-17-generic root=UUID=9e70fd16-b48b-4f88-adcf-e443aef83124 ro recovery nomodeset echo 'Loading initial ramdisk ...' initrd /boot/initrd.img-3.5.0-17-generic } } ### END /etc/grub.d/10_linux ### ### BEGIN /etc/grub.d/20_linux_xen ### ### END /etc/grub.d/20_linux_xen ### ### BEGIN /etc/grub.d/20_memtest86+ ### menuentry "Memory test (memtest86+)" { insmod part_msdos insmod ext2 set root='hd0,msdos6' if [ x$feature_platform_search_hint = xy ]; then search --no-floppy --fs-uuid --set=root --hint-bios=hd0,msdos6 --hint-efi=hd0,msdos6 --hint-baremetal=ahci0,msdos6 9e70fd16-b48b-4f88-adcf-e443aef83124 else search --no-floppy --fs-uuid --set=root 9e70fd16-b48b-4f88-adcf-e443aef83124 fi linux16 /boot/memtest86+.bin } menuentry "Memory test (memtest86+, serial console 115200)" { insmod part_msdos insmod ext2 set root='hd0,msdos6' if [ x$feature_platform_search_hint = xy ]; then search --no-floppy --fs-uuid --set=root --hint-bios=hd0,msdos6 --hint-efi=hd0,msdos6 --hint-baremetal=ahci0,msdos6 9e70fd16-b48b-4f88-adcf-e443aef83124 else search --no-floppy --fs-uuid --set=root 9e70fd16-b48b-4f88-adcf-e443aef83124 fi linux16 /boot/memtest86+.bin console=ttyS0,115200n8 } ### END /etc/grub.d/20_memtest86+ ### ### BEGIN /etc/grub.d/30_os-prober ### menuentry 'Windows 7 (loader) (on /dev/sda1)' --class windows --class os $menuentry_id_option 'osprober-chain-F6AE2C13AE2BCB47' { insmod part_msdos insmod ntfs set root='hd0,msdos1' if [ x$feature_platform_search_hint = xy ]; then search --no-floppy --fs-uuid --set=root --hint-bios=hd0,msdos1 --hint-efi=hd0,msdos1 --hint-baremetal=ahci0,msdos1 F6AE2C13AE2BCB47 else search --no-floppy --fs-uuid --set=root F6AE2C13AE2BCB47 fi chainloader +1 } ### END /etc/grub.d/30_os-prober ### ### BEGIN /etc/grub.d/30_uefi-firmware ### ### END /etc/grub.d/30_uefi-firmware ### ### BEGIN /etc/grub.d/40_custom ### # This file provides an easy way to add custom menu entries. Simply type the # menu entries you want to add after this comment. Be careful not to change # the 'exec tail' line above. ### END /etc/grub.d/40_custom ### ### BEGIN /etc/grub.d/41_custom ### if [ -f ${config_directory}/custom.cfg ]; then source ${config_directory}/custom.cfg elif [ -z "${config_directory}" -a -f $prefix/custom.cfg ]; then source $prefix/custom.cfg; fi ### END /etc/grub.d/41_custom ### -------------------------------------------------------------------------------- =============================== sda6/etc/fstab: ================================ -------------------------------------------------------------------------------- # /etc/fstab: static file system information. # # Use 'blkid' to print the universally unique identifier for a # device; this may be used with UUID= as a more robust way to name devices # that works even if disks are added and removed. See fstab(5). # # <file system> <mount point> <type> <options> <dump> <pass> # / was on /dev/sda6 during installation UUID=9e70fd16-b48b-4f88-adcf-e443aef83124 / ext4 errors=remount-ro 0 1 # swap was on /dev/sda7 during installation UUID=52f3dd94-6be7-4a7b-a3ae-f43eb8810483 none swap sw 0 0 -------------------------------------------------------------------------------- =================== sda6: Location of files loaded by Grub: ==================== GiB - GB File Fragment(s) 162.831275940 = 174.838751232 boot/grub/grub.cfg 1 163.036647797 = 175.059267584 boot/initrd.img-3.5.0-17-generic 1 206.871749878 = 222.126850048 boot/vmlinuz-3.5.0-17-generic 1 163.036647797 = 175.059267584 initrd.img 1 163.036647797 = 175.059267584 initrd.img.old 1 206.871749878 = 222.126850048 vmlinuz 1 =============================== StdErr Messages: =============================== cat: write error: Broken pipe cat: write error: Broken pipe ADDITIONAL INFORMATION : =================== log of boot-repair 2012-12-11__00h59 =================== boot-repair version : 3.195~ppa28~quantal boot-sav version : 3.195~ppa28~quantal glade2script version : 3.2.2~ppa45~quantal boot-sav-extra version : 3.195~ppa28~quantal boot-repair is executed in installed-session (Ubuntu 12.10, quantal, Ubuntu, x86_64) CPU op-mode(s): 32-bit, 64-bit BOOT_IMAGE=/boot/vmlinuz-3.5.0-17-generic root=UUID=9e70fd16-b48b-4f88-adcf-e443aef83124 ro quiet splash vt.handoff=7 =================== os-prober: /dev/sda6:The OS now in use - Ubuntu 12.10 CurrentSession:linux /dev/sda1:Windows 7 (loader):Windows:chain =================== blkid: /dev/sda1: UUID="F6AE2C13AE2BCB47" TYPE="ntfs" /dev/sda2: UUID="DC2273012272DFC6" TYPE="ntfs" /dev/sda3: LABEL="New Volume" UUID="1E76E43376E40D79" TYPE="ntfs" /dev/sda5: UUID="5ED60ACDD60AA57D" TYPE="ntfs" /dev/sda6: UUID="9e70fd16-b48b-4f88-adcf-e443aef83124" TYPE="ext4" /dev/sda7: UUID="52f3dd94-6be7-4a7b-a3ae-f43eb8810483" TYPE="swap" 1 disks with OS, 2 OS : 1 Linux, 0 MacOS, 1 Windows, 0 unknown type OS. Warning: extended partition does not start at a cylinder boundary. DOS and Linux will interpret the contents differently. =================== /etc/default/grub : # If you change this file, run 'update-grub' afterwards to update # /boot/grub/grub.cfg. # For full documentation of the options in this file, see: # info -f grub -n 'Simple configuration' GRUB_DEFAULT=0 #GRUB_HIDDEN_TIMEOUT=0 GRUB_HIDDEN_TIMEOUT_QUIET=true GRUB_TIMEOUT=10 GRUB_DISTRIBUTOR=`lsb_release -i -s 2> /dev/null || echo Debian` GRUB_CMDLINE_LINUX_DEFAULT="quiet splash" GRUB_CMDLINE_LINUX="" # Uncomment to enable BadRAM filtering, modify to suit your needs # This works with Linux (no patch required) and with any kernel that obtains # the memory map information from GRUB (GNU Mach, kernel of FreeBSD ...) #GRUB_BADRAM="0x01234567,0xfefefefe,0x89abcdef,0xefefefef" # Uncomment to disable graphical terminal (grub-pc only) #GRUB_TERMINAL=console # The resolution used on graphical terminal # note that you can use only modes which your graphic card supports via VBE # you can see them in real GRUB with the command `vbeinfo' #GRUB_GFXMODE=640x480 # Uncomment if you don't want GRUB to pass "root=UUID=xxx" parameter to Linux #GRUB_DISABLE_LINUX_UUID=true # Uncomment to disable generation of recovery mode menu entries #GRUB_DISABLE_RECOVERY="true" # Uncomment to get a beep at grub start #GRUB_INIT_TUNE="480 440 1" =================== /etc/grub.d/ : drwxr-xr-x 2 root root 4096 Oct 17 20:29 grub.d total 72 -rwxr-xr-x 1 root root 7541 Oct 14 23:06 00_header -rwxr-xr-x 1 root root 5488 Oct 4 15:00 05_debian_theme -rwxr-xr-x 1 root root 10891 Oct 14 23:06 10_linux -rwxr-xr-x 1 root root 10258 Oct 14 23:06 20_linux_xen -rwxr-xr-x 1 root root 1688 Oct 11 19:40 20_memtest86+ -rwxr-xr-x 1 root root 10976 Oct 14 23:06 30_os-prober -rwxr-xr-x 1 root root 1426 Oct 14 23:06 30_uefi-firmware -rwxr-xr-x 1 root root 214 Oct 14 23:06 40_custom -rwxr-xr-x 1 root root 216 Oct 14 23:06 41_custom -rw-r--r-- 1 root root 483 Oct 14 23:06 README =================== UEFI/Legacy mode: This installed-session is not in EFI-mode. EFI in dmesg. Please report this message to [email protected] [ 0.000000] ACPI: UEFI 00000000bafe7000 0003E (v01 DELL QA09 00000002 PTL 00000002) [ 0.000000] ACPI: UEFI 00000000bafe6000 00042 (v01 PTL COMBUF 00000001 PTL 00000001) [ 0.000000] ACPI: UEFI 00000000bafe3000 00256 (v01 DELL QA09 00000002 PTL 00000002) SecureBoot disabled. =================== PARTITIONS & DISKS: sda6 : sda, not-sepboot, grubenv-ok grub2, grub-pc , update-grub, 64, with-boot, is-os, not--efi--part, fstab-without-boot, fstab-without-efi, no-nt, no-winload, no-recov-nor-hid, no-bmgr, notwinboot, apt-get, grub-install, with--usr, fstab-without-usr, not-sep-usr, standard, farbios, . sda1 : sda, not-sepboot, no-grubenv nogrub, no-docgrub, no-update-grub, 32, no-boot, is-os, not--efi--part, part-has-no-fstab, part-has-no-fstab, no-nt, haswinload, no-recov-nor-hid, bootmgr, is-winboot, nopakmgr, nogrubinstall, no---usr, part-has-no-fstab, not-sep-usr, standard, not-far, /mnt/boot-sav/sda1. sda2 : sda, not-sepboot, no-grubenv nogrub, no-docgrub, no-update-grub, 32, no-boot, no-os, not--efi--part, part-has-no-fstab, part-has-no-fstab, no-nt, no-winload, no-recov-nor-hid, no-bmgr, notwinboot, nopakmgr, nogrubinstall, no---usr, part-has-no-fstab, not-sep-usr, standard, farbios, /mnt/boot-sav/sda2. sda3 : sda, not-sepboot, no-grubenv nogrub, no-docgrub, no-update-grub, 32, no-boot, no-os, not--efi--part, part-has-no-fstab, part-has-no-fstab, no-nt, no-winload, no-recov-nor-hid, no-bmgr, notwinboot, nopakmgr, nogrubinstall, no---usr, part-has-no-fstab, not-sep-usr, standard, farbios, /mnt/boot-sav/sda3. sda5 : sda, not-sepboot, no-grubenv nogrub, no-docgrub, no-update-grub, 32, no-boot, no-os, not--efi--part, part-has-no-fstab, part-has-no-fstab, no-nt, no-winload, no-recov-nor-hid, no-bmgr, notwinboot, nopakmgr, nogrubinstall, no---usr, part-has-no-fstab, not-sep-usr, standard, farbios, /mnt/boot-sav/sda5. sda : not-GPT, BIOSboot-not-needed, has-no-EFIpart, not-usb, has-os, 2048 sectors * 512 bytes =================== parted -l: Model: ATA WDC WD7500BPKT-7 (scsi) Disk /dev/sda: 750GB Sector size (logical/physical): 512B/4096B Partition Table: msdos Number Start End Size Type File system Flags 1 106MB 75.2GB 75.1GB primary ntfs boot 2 75.3GB 150GB 75.1GB primary ntfs 3 150GB 170GB 20.1GB primary ntfs 4 170GB 750GB 580GB extended lba 6 170GB 232GB 61.6GB logical ext4 7 232GB 236GB 4181MB logical linux-swap(v1) 5 236GB 750GB 514GB logical ntfs =================== parted -lm: BYT; /dev/sda:750GB:scsi:512:4096:msdos:ATA WDC WD7500BPKT-7; 1:106MB:75.2GB:75.1GB:ntfs::boot; 2:75.3GB:150GB:75.1GB:ntfs::; 3:150GB:170GB:20.1GB:ntfs::; 4:170GB:750GB:580GB:::lba; 6:170GB:232GB:61.6GB:ext4::; 7:232GB:236GB:4181MB:linux-swap(v1)::; 5:236GB:750GB:514GB:ntfs::; =================== mount: /dev/sda6 on / type ext4 (rw,errors=remount-ro) proc on /proc type proc (rw,noexec,nosuid,nodev) sysfs on /sys type sysfs (rw,noexec,nosuid,nodev) none on /sys/fs/fuse/connections type fusectl (rw) none on /sys/kernel/debug type debugfs (rw) none on /sys/kernel/security type securityfs (rw) udev on /dev type devtmpfs (rw,mode=0755) devpts on /dev/pts type devpts (rw,noexec,nosuid,gid=5,mode=0620) tmpfs on /run type tmpfs (rw,noexec,nosuid,size=10%,mode=0755) none on /run/lock type tmpfs (rw,noexec,nosuid,nodev,size=5242880) none on /run/shm type tmpfs (rw,nosuid,nodev) none on /run/user type tmpfs (rw,noexec,nosuid,nodev,size=104857600,mode=0755) gvfsd-fuse on /run/user/dev/gvfs type fuse.gvfsd-fuse (rw,nosuid,nodev,user=dev) /dev/sda1 on /mnt/boot-sav/sda1 type fuseblk (rw,nosuid,nodev,allow_other,blksize=4096) /dev/sda2 on /mnt/boot-sav/sda2 type fuseblk (rw,nosuid,nodev,allow_other,blksize=4096) /dev/sda3 on /mnt/boot-sav/sda3 type fuseblk (rw,nosuid,nodev,allow_other,blksize=4096) /dev/sda5 on /mnt/boot-sav/sda5 type fuseblk (rw,nosuid,nodev,allow_other,blksize=4096) =================== ls: /sys/block/sda (filtered): alignment_offset bdi capability dev device discard_alignment events events_async events_poll_msecs ext_range holders inflight power queue range removable ro sda1 sda2 sda3 sda4 sda5 sda6 sda7 size slaves stat subsystem trace uevent /sys/block/sr0 (filtered): alignment_offset bdi capability dev device discard_alignment events events_async events_poll_msecs ext_range holders inflight power queue range removable ro size slaves stat subsystem trace uevent /dev (filtered): alarm ashmem autofs binder block bsg btrfs-control bus cdrom cdrw char console core cpu cpu_dma_latency disk dri dvd dvdrw ecryptfs fb0 fb1 fd full fuse hpet input kmsg kvm log mapper mcelog mei mem net network_latency network_throughput null oldmem port ppp psaux ptmx pts random rfkill rtc rtc0 sda sda1 sda2 sda3 sda4 sda5 sda6 sda7 sg0 sg1 shm snapshot snd sr0 stderr stdin stdout uinput urandom v4l vga_arbiter vhost-net video0 zero ls /dev/mapper: control =================== df -Th: Filesystem Type Size Used Avail Use% Mounted on /dev/sda6 ext4 57G 2.7G 51G 6% / udev devtmpfs 1.9G 12K 1.9G 1% /dev tmpfs tmpfs 770M 892K 769M 1% /run none tmpfs 5.0M 0 5.0M 0% /run/lock none tmpfs 1.9G 260K 1.9G 1% /run/shm none tmpfs 100M 44K 100M 1% /run/user /dev/sda1 fuseblk 70G 36G 35G 51% /mnt/boot-sav/sda1 /dev/sda2 fuseblk 70G 66G 4.8G 94% /mnt/boot-sav/sda2 /dev/sda3 fuseblk 19G 87M 19G 1% /mnt/boot-sav/sda3 /dev/sda5 fuseblk 479G 436G 44G 92% /mnt/boot-sav/sda5 =================== fdisk -l: Disk /dev/sda: 750.2 GB, 750156374016 bytes 255 heads, 63 sectors/track, 91201 cylinders, total 1465149168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 4096 bytes I/O size (minimum/optimal): 4096 bytes / 4096 bytes Disk identifier: 0x1dc69d0b Device Boot Start End Blocks Id System /dev/sda1 * 206848 146802687 73297920 7 HPFS/NTFS/exFAT /dev/sda2 147007488 293623807 73308160 7 HPFS/NTFS/exFAT /dev/sda3 293623808 332820613 19598403 7 HPFS/NTFS/exFAT /dev/sda4 332822526 1465145343 566161409 f W95 Ext'd (LBA) Partition 4 does not start on physical sector boundary. /dev/sda5 461342720 1465145343 501901312 7 HPFS/NTFS/exFAT /dev/sda6 332822528 453171199 60174336 83 Linux /dev/sda7 453173248 461338623 4082688 82 Linux swap / Solaris Partition table entries are not in disk order =================== Recommended repair Recommended-Repair This setting will reinstall the grub2 of sda6 into the MBR of sda. Additional repair will be performed: unhide-bootmenu-10s grub-install (GRUB) 2.00-7ubuntu11,grub-install (GRUB) 2. Reinstall the GRUB of sda6 into the MBR of sda Installation finished. No error reported. grub-install /dev/sda: exit code of grub-install /dev/sda:0 update-grub Generating grub.cfg ... Found linux image: /boot/vmlinuz-3.5.0-17-generic Found initrd image: /boot/initrd.img-3.5.0-17-generic Found memtest86+ image: /boot/memtest86+.bin Found Windows 7 (loader) on /dev/sda1 Unhide GRUB boot menu in sda6/boot/grub/grub.cfg Boot successfully repaired. You can now reboot your computer. The boot files of [The OS now in use - Ubuntu 12.10] are far from the start of the disk. Your BIOS may not detect them. You may want to retry after creating a /boot partition (EXT4, >200MB, start of the disk). This can be performed via tools such as gParted. Then select this partition via the [Separate /boot partition:] option of [Boot Repair]. (https://help.ubuntu.com/community/BootPartition)

  Read the article

• IRP_MJ_WRITE latency up to 15 seconds

  - by racitup

  We have written an application that performs small (22kB) writes to multiple files at once (one thread performing asynchronous queued writes to multiple locations on behalf of other threads) on the same local volume (RAID1). 99.9% of the writes are low-latency but occasionally (maybe every minute or two) we get one or two huge latency writes (I have seen 10 seconds and above) without any real explanation. Platform: Win2003 Server with NTFS. Monitoring: Sysinternals Process Monitor (see link below) and our own application logging. We have tried multiple things to try and solve this that have been gleaned from a few websites, e.g.: Making the first part of file names unique to aid 8.3 name generation Writing files to multiple directories Changing Intel Disk Write Caching Windows File/Printer Sharing Minimize memory used Balance Maximize data throughput for file sharing Maximize data throughput for network applications System-Advanced-Performance-Advanced NtfsDisableLastAccessUpdate - use fsutil behavior set disablelastaccess 1 disable 8.3 name generation - use "fsutil behavior set disable8dot3 1" + restart Enable a large size file system cache Disable paging of the kernel code IO Page Lock Limit Turn Off (or On) the Indexing Service But nothing seems to make much difference. There's a whole host of things we haven't tried yet but we wondered if anyone had come across the same problem, a reason and a solution (programmatic or not)? We can reproduce the problem using IOMeter and a simple setup: Start IOMeter and remove all but the first worker thread in 'Topology' using the disconnect button. Select the Worker thread and put a cross in the box next to the disk you want to use in the Disk Targets tab and put '2000000' in Maximum Disk Size (NOTE: must have at least 1GB free space; sector size is 512 bytes) Next create a new access specification and add it to the worker thread: Transfer Request Size = 22kB 100% Sequential Percent of Access Spec = 100% Percent Read/Write = 100% Write Change Results Display Update Frequency to 5 seconds, Test Setup Run Time to 20 seconds and both 'Number of Workers to Spawn Automatically' settings to zero. Select the Worker Thread in the Topology panel and hit the Duplicate Worker button 59 times to create 60 threads with identical settings. Hit the 'Go' button (green flag) and monitor the Results tab. The 'Maximum I/O Response Time (ms)' always hits at least 3500 on our machine. Our machine isn't exactly slow (Xeon 8 core rack server with 4GB and onboard RAID). I'd be interested to see what other people get. We have a feeling it might be something to do with the NTFS filesystem (ours is currently 75% full of fragmented files) and we are going to try a few things around this principle. But it is also related to disk performance since we don't see it on a RAMDisk and it's not as severe on a RAID10 array. Any help is much appreciated. Richard Right-click and select 'Open Link in New Tab': ProcMon Result

  Read the article

• Ubuntu 12.04 doesn't recgonize m CPU correctly

  - by Nightshaxx

  My computer is running ubuntu 12.04 (64bit), and I have a AMD Athlon(tm) X4 760K Quad Core Processor which is about 3.8ghz (and an Radeon HD 7770 GPU). Yet, when I type in cat /proc/cpuinfo - I get: processor : 0 vendor_id : AuthenticAMD cpu family : 21 model : 19 model name : AMD Athlon(tm) X4 760K Quad Core Processor stepping : 1 microcode : 0x6001119 cpu MHz : 1800.000 cache size : 2048 KB physical id : 0 siblings : 4 core id : 0 cpu cores : 2 apicid : 16 initial apicid : 0 fpu : yes fpu_exception : yes cpuid level : 13 wp : yes flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 clflush mmx fxsr sse sse2 ht syscall nx mmxext fxsr_opt pdpe1gb rdtscp lm constant_tsc rep_good nopl nonstop_tsc extd_apicid aperfmperf pni pclmulqdq monitor ssse3 fma cx16 sse4_1 sse4_2 popcnt aes xsave avx f16c lahf_lm cmp_legacy svm extapic cr8_legacy abm sse4a misalignsse 3dnowprefetch osvw ibs xop skinit wdt lwp fma4 tce nodeid_msr tbm topoext perfctr_core arat cpb hw_pstate npt lbrv svm_lock nrip_save tsc_scale vmcb_clean flushbyasid decodeassists pausefilter pfthreshold bmi1 bogomips : 7599.97 TLB size : 1536 4K pages clflush size : 64 cache_alignment : 64 address sizes : 48 bits physical, 48 bits virtual power management: ts ttp tm 100mhzsteps hwpstate cpb eff_freq_ro processor : 1 vendor_id : AuthenticAMD cpu family : 21 model : 19 model name : AMD Athlon(tm) X4 760K Quad Core Processor stepping : 1 microcode : 0x6001119 cpu MHz : 1800.000 cache size : 2048 KB physical id : 0 siblings : 4 core id : 1 cpu cores : 2 apicid : 17 initial apicid : 1 fpu : yes fpu_exception : yes cpuid level : 13 wp : yes flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 clflush mmx fxsr sse sse2 ht syscall nx mmxext fxsr_opt pdpe1gb rdtscp lm constant_tsc rep_good nopl nonstop_tsc extd_apicid aperfmperf pni pclmulqdq monitor ssse3 fma cx16 sse4_1 sse4_2 popcnt aes xsave avx f16c lahf_lm cmp_legacy svm extapic cr8_legacy abm sse4a misalignsse 3dnowprefetch osvw ibs xop skinit wdt lwp fma4 tce nodeid_msr tbm topoext perfctr_core arat cpb hw_pstate npt lbrv svm_lock nrip_save tsc_scale vmcb_clean flushbyasid decodeassists pausefilter pfthreshold bmi1 bogomips : 7599.97 TLB size : 1536 4K pages clflush size : 64 cache_alignment : 64 address sizes : 48 bits physical, 48 bits virtual power management: ts ttp tm 100mhzsteps hwpstate cpb eff_freq_ro processor : 2 vendor_id : AuthenticAMD cpu family : 21 model : 19 model name : AMD Athlon(tm) X4 760K Quad Core Processor stepping : 1 microcode : 0x6001119 cpu MHz : 1800.000 cache size : 2048 KB physical id : 0 siblings : 4 core id : 2 cpu cores : 2 apicid : 18 initial apicid : 2 fpu : yes fpu_exception : yes cpuid level : 13 wp : yes flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 clflush mmx fxsr sse sse2 ht syscall nx mmxext fxsr_opt pdpe1gb rdtscp lm constant_tsc rep_good nopl nonstop_tsc extd_apicid aperfmperf pni pclmulqdq monitor ssse3 fma cx16 sse4_1 sse4_2 popcnt aes xsave avx f16c lahf_lm cmp_legacy svm extapic cr8_legacy abm sse4a misalignsse 3dnowprefetch osvw ibs xop skinit wdt lwp fma4 tce nodeid_msr tbm topoext perfctr_core arat cpb hw_pstate npt lbrv svm_lock nrip_save tsc_scale vmcb_clean flushbyasid decodeassists pausefilter pfthreshold bmi1 bogomips : 7599.97 TLB size : 1536 4K pages clflush size : 64 cache_alignment : 64 address sizes : 48 bits physical, 48 bits virtual power management: ts ttp tm 100mhzsteps hwpstate cpb eff_freq_ro processor : 3 vendor_id : AuthenticAMD cpu family : 21 model : 19 model name : AMD Athlon(tm) X4 760K Quad Core Processor stepping : 1 microcode : 0x6001119 cpu MHz : 1800.000 cache size : 2048 KB physical id : 0 siblings : 4 core id : 3 cpu cores : 2 apicid : 19 initial apicid : 3 fpu : yes fpu_exception : yes cpuid level : 13 wp : yes flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 clflush mmx fxsr sse sse2 ht syscall nx mmxext fxsr_opt pdpe1gb rdtscp lm constant_tsc rep_good nopl nonstop_tsc extd_apicid aperfmperf pni pclmulqdq monitor ssse3 fma cx16 sse4_1 sse4_2 popcnt aes xsave avx f16c lahf_lm cmp_legacy svm extapic cr8_legacy abm sse4a misalignsse 3dnowprefetch osvw ibs xop skinit wdt lwp fma4 tce nodeid_msr tbm topoext perfctr_core arat cpb hw_pstate npt lbrv svm_lock nrip_save tsc_scale vmcb_clean flushbyasid decodeassists pausefilter pfthreshold bmi1 bogomips : 7599.97 TLB size : 1536 4K pages clflush size : 64 cache_alignment : 64 address sizes : 48 bits physical, 48 bits virtual power management: ts ttp tm 100mhzsteps hwpstate cpb eff_freq_ro The important part of all this being, cpu MHz : 1800.000 which indicates that I have only 1.8ghz of processing power, which is totally wrong. Is it something with drivers or Ubuntu?? Also, will windows recognize all of my processing power? Thanks! (NOTE: My cpu doesn't have intigrated graphics

  Read the article

• High Load mysql on Debian server

  - by Oleg Abrazhaev

  I have Debian server with 32 gb memory. And there is apache2, memcached and nginx on this server. Memory load always on maximum. Only 500m free. Most memory leak do MySql. Apache only 70 clients configured, other services small memory usage. When mysql use all memory it stops. And nothing works, need mysql reboot. Mysql configured use maximum 24 gb memory. I have hight weight InnoDB bases. (400000 rows, 30 gb). And on server multithread daemon, that makes many inserts in this tables, thats why InnoDB. There is my mysql config. [mysqld] # # * Basic Settings # default-time-zone = "+04:00" user = mysql pid-file = /var/run/mysqld/mysqld.pid socket = /var/run/mysqld/mysqld.sock port = 3306 basedir = /usr datadir = /var/lib/mysql tmpdir = /tmp language = /usr/share/mysql/english skip-external-locking default-time-zone='Europe/Moscow' # # Instead of skip-networking the default is now to listen only on # localhost which is more compatible and is not less secure. # # * Fine Tuning # #low_priority_updates = 1 concurrent_insert = ALWAYS wait_timeout = 600 interactive_timeout = 600 #normal key_buffer_size = 2024M #key_buffer_size = 1512M #70% hot cache key_cache_division_limit= 70 #16-32 max_allowed_packet = 32M #1-16M thread_stack = 8M #40-50 thread_cache_size = 50 #orderby groupby sort sort_buffer_size = 64M #same myisam_sort_buffer_size = 400M #temp table creates when group_by tmp_table_size = 3000M #tables in memory max_heap_table_size = 3000M #on disk open_files_limit = 10000 table_cache = 10000 join_buffer_size = 5M # This replaces the startup script and checks MyISAM tables if needed # the first time they are touched myisam-recover = BACKUP #myisam_use_mmap = 1 max_connections = 200 thread_concurrency = 8 # # * Query Cache Configuration # #more ignored query_cache_limit = 50M query_cache_size = 210M #on query cache query_cache_type = 1 # # * Logging and Replication # # Both location gets rotated by the cronjob. # Be aware that this log type is a performance killer. #log = /var/log/mysql/mysql.log # # Error logging goes to syslog. This is a Debian improvement :) # # Here you can see queries with especially long duration log_slow_queries = /var/log/mysql/mysql-slow.log long_query_time = 1 log-queries-not-using-indexes # # The following can be used as easy to replay backup logs or for replication. # note: if you are setting up a replication slave, see README.Debian about # other settings you may need to change. #server-id = 1 #log_bin = /var/log/mysql/mysql-bin.log server-id = 1 log-bin = /var/lib/mysql/mysql-bin #replicate-do-db = gate log-bin-index = /var/lib/mysql/mysql-bin.index log-error = /var/lib/mysql/mysql-bin.err relay-log = /var/lib/mysql/relay-bin relay-log-info-file = /var/lib/mysql/relay-bin.info relay-log-index = /var/lib/mysql/relay-bin.index binlog_do_db = 24avia expire_logs_days = 10 max_binlog_size = 100M read_buffer_size = 4024288 innodb_buffer_pool_size = 5000M innodb_flush_log_at_trx_commit = 2 innodb_thread_concurrency = 8 table_definition_cache = 2000 group_concat_max_len = 16M #binlog_do_db = gate #binlog_ignore_db = include_database_name # # * BerkeleyDB # # Using BerkeleyDB is now discouraged as its support will cease in 5.1.12. #skip-bdb # # * InnoDB # # InnoDB is enabled by default with a 10MB datafile in /var/lib/mysql/. # Read the manual for more InnoDB related options. There are many! # You might want to disable InnoDB to shrink the mysqld process by circa 100MB. #skip-innodb # # * Security Features # # Read the manual, too, if you want chroot! # chroot = /var/lib/mysql/ # # For generating SSL certificates I recommend the OpenSSL GUI "tinyca". # # ssl-ca=/etc/mysql/cacert.pem # ssl-cert=/etc/mysql/server-cert.pem # ssl-key=/etc/mysql/server-key.pem [mysqldump] quick quote-names max_allowed_packet = 500M [mysql] #no-auto-rehash # faster start of mysql but no tab completition [isamchk] key_buffer = 32M key_buffer_size = 512M # # * NDB Cluster # # See /usr/share/doc/mysql-server-*/README.Debian for more information. # # The following configuration is read by the NDB Data Nodes (ndbd processes) # not from the NDB Management Nodes (ndb_mgmd processes). # # [MYSQL_CLUSTER] # ndb-connectstring=127.0.0.1 # # * IMPORTANT: Additional settings that can override those from this file! # The files must end with '.cnf', otherwise they'll be ignored. # !includedir /etc/mysql/conf.d/ Please, help me make it stable. Memory used /etc/mysql # free total used free shared buffers cached Mem: 32930800 32766424 164376 0 139208 23829196 -/+ buffers/cache: 8798020 24132780 Swap: 33553328 44660 33508668 Maybe my problem not in memory, but MySQL stops every day. As you can see, cache memory free 24 gb. Thank to Michael Hampton? for correction. Load overage on server 3.5. Maybe hdd or another problem? Maybe my config not optimal for 30gb InnoDB ?

  Read the article

• chkdsk, SeaTools, and "does not have enough space to replace bad clusters"

  - by Zian Choy

  When I tried to do a Windows Vista Complete PC Backup, I received an error message that blathered about bad sectors. Then, when I ran chkdsk /r on the destination drive, this is what I got: C:\Windows\system32>chkdsk /R E: The type of the file system is NTFS. Volume label is Desktop Backup. CHKDSK is verifying files (stage 1 of 5)... 822016 file records processed. File verification completed. 1 large file records processed. 0 bad file records processed. 0 EA records processed. 0 reparse records processed. CHKDSK is verifying indexes (stage 2 of 5)... 848938 index entries processed. Index verification completed. 0 unindexed files processed. CHKDSK is verifying security descriptors (stage 3 of 5)... 822016 security descriptors processed. Security descriptor verification completed. 13461 data files processed. CHKDSK is verifying file data (stage 4 of 5)... The disk does not have enough space to replace bad clusters detected in file 239649 of name . The disk does not have enough space to replace bad clusters detected in file 239650 of name . The disk does not have enough space to replace bad clusters detected in file 239651 of name . An unspecified error occurred.f 822000 files processed) Yet, when I ran the SeaTools short & long generic tests on the Seagate disk, I didn't receive any errors. I know that I could reformat the disk and try running chkdsk /r again but I'd prefer to avoid waiting 4 hours in the hope that the problem was magically fixed. On the other hand, if I RmA the drive to Seagate, I have no SeaTools error number to use and they may claim that the drive is just fine. What should I try to do next? Side frustration: There is plenty of free hard drive space. The E: partition has 182 GB free.

  Read the article

• Why do I see a large performance hit with DRBD?

  - by BHS

  I see a much larger performance hit with DRBD than their user manual says I should get. I'm using DRBD 8.3.7 (Fedora 13 RPMs). I've setup a DRBD test and measured throughput of disk and network without DRBD: dd if=/dev/zero of=/data.tmp bs=512M count=1 oflag=direct 536870912 bytes (537 MB) copied, 4.62985 s, 116 MB/s / is a logical volume on the disk I'm testing with, mounted without DRBD iperf: [ 4] 0.0-10.0 sec 1.10 GBytes 941 Mbits/sec According to Throughput overhead expectations, the bottleneck would be whichever is slower, the network or the disk and DRBD should have an overhead of 3%. In my case network and I/O seem to be pretty evenly matched. It sounds like I should be able to get around 100 MB/s. So, with the raw drbd device, I get dd if=/dev/zero of=/dev/drbd2 bs=512M count=1 oflag=direct 536870912 bytes (537 MB) copied, 6.61362 s, 81.2 MB/s which is slower than I would expect. Then, once I format the device with ext4, I get dd if=/dev/zero of=/mnt/data.tmp bs=512M count=1 oflag=direct 536870912 bytes (537 MB) copied, 9.60918 s, 55.9 MB/s This doesn't seem right. There must be some other factor playing into this that I'm not aware of. global_common.conf global { usage-count yes; } common { protocol C; } syncer { al-extents 1801; rate 33M; } data_mirror.res resource data_mirror { device /dev/drbd1; disk /dev/sdb1; meta-disk internal; on cluster1 { address 192.168.33.10:7789; } on cluster2 { address 192.168.33.12:7789; } } For the hardware I have two identical machines: 6 GB RAM Quad core AMD Phenom 3.2Ghz Motherboard SATA controller 7200 RPM 64MB cache 1TB WD drive The network is 1Gb connected via a switch. I know that a direct connection is recommended, but could it make this much of a difference? Edited I just tried monitoring the bandwidth used to try to see what's happening. I used ibmonitor and measured average bandwidth while I ran the dd test 10 times. I got: avg ~450Mbits writing to ext4 avg ~800Mbits writing to raw device It looks like with ext4, drbd is using about half the bandwidth it uses with the raw device so there's a bottleneck that is not the network.

  Read the article

• Both 12.10&12.04 Installation freeze

  - by Fih

  A friend of mine is having problems installing Ubuntu. We've tried both 12.10 and 12.04 ver. but each time we get http://img513.imageshack.us/img513/6332/27456089.png and then we got stuck. His comp is: Motherboard: ASUS P5G41-M LX CPU: Pentium(R) Dual-Core CPU E6500 @ 2.93GHz DISK: Disk 500.1 GB SAMSUNG HD502HJ RAM: Slot 1 DDR2 (PC2-6400) 2048 MB Kingston Slot 2 DDR2 (PC2-6400) 2048 MB Hyundai Electronics Graph card: NVIDIA GeForce GT 240 Any solution to this? Bests, Dwig

  Read the article

• SQL SERVER – OLEDB – Link Server – Wait Type – Day 23 of 28

  - by pinaldave

  When I decided to start writing about this wait type, the very first question that came to my mind was, “What does ‘OLEDB’ stand for?” A quick search on Wikipedia tells me that OLEDB means Object Linking and Embedding Database. (How many of you knew this?) Anyway, I found it very interesting that this wait type was in one of the top 10 wait types in many of the systems I have come across in my performance tuning experience. Books On-Line: ????OLEDB occurs when SQL Server calls the SQL Server Native Client OLE DB Provider. This wait type is not used for synchronization. Instead, it indicates the duration of calls to the OLE DB provider. OLEDB Explanation: This wait type primarily happens when Link Server or Remove Query has been executed. The most common case wherein this wait type is visible is during the execution of Linked Server. When SQL Server is retrieving data from the remote server, it uses OLEDB API to retrieve the data. It is possible that the remote system is not quick enough or the connection between them is not fast enough, leading SQL Server to wait for the result’s return from the remote (or external) server. This is the time OLEDB wait type occurs. Reducing OLEDB wait: Check the Link Server configuration. Checking Disk-Related Perfmon Counters Average Disk sec/Read (Consistent higher value than 4-8 millisecond is not good) Average Disk sec/Write (Consistent higher value than 4-8 millisecond is not good) Average Disk Read/Write Queue Length (Consistent higher value than benchmark is not good) At this point in time, I am not able to think of any more ways on reducing this wait type. Do you have any opinion about this subject? Please share it here and I will share your comment with the rest of the Community, and of course, with due credit unto you. Please read all the post in the Wait Types and Queue series. Note: The information presented here is from my experience and there is no way that I claim it to be accurate. I suggest reading Book OnLine for further clarification. All the discussion of Wait Stats in this blog is generic and varies from system to system. It is recommended that you test this on a development server before implementing it to a production server. Reference: Pinal Dave (http://blog.SQLAuthority.com) Filed under: Pinal Dave, PostADay, SQL, SQL Authority, SQL Query, SQL Server, SQL Tips and Tricks, SQL Wait Stats, SQL Wait Types, T SQL, Technology

  Read the article

• Hard drive mounted at / , duplicate mounted hard drive after using MountManager

  - by HellHarvest

  possible duplicate post I'm running 12.04 64bit. My system is a dual boot for both Ubuntu and Windows7. Both operating systems are sharing the drive named "Elements". My volume named "Elements" is a 1TB SATA NTFS hard drive that shows up twice in the side bar in nautilus. One of the icons is functional and even has the convenient "eject" icon next to it. Below is a picture of the left menu in Nautilus, with System Monitor-File Systems tab open on top of it. Can someone advise me about how to get rid of this extra icon? I think the problem is much more deep-rooted than just a GUI glitch on Nautilus' part. The other icon does nothing but spit out the following error when I click on it (image below). This only happened AFTER I tried using Mount Manager to automate mounting the drive at start up. I've already uninstalled Mount Manager, and restarted, but the problem didn't go away. The hard drive does mount automatically now, so I guess that's cool. But now, every time I boot up now and open Nautilus, BOTH of these icons appear, one of which is fictitious and useless. According to the image above and the outputs of several other commands, it appears to be mounted at / In which case, no matter where I am in Nautilus when I try to click on that icon, of course it will tell me that that drive is in use by another program... Nautilus. I'm afraid of trying to unmount this hard drive (sdb6) because of where it appears to be mounted. I'm kind of a noob, and I have this gut feeling that tells me trying to unmount a drive at / will destroy my entire file system. This fear was further strengthened by the output of "$ fsck" at the very bottom of this post. Error immediately below when that 2nd "Elements" hard drive is clicked in Nautilus: Unable to mount Elements Mount is denied because the NTFS volume is already exclusively opened. The volume may be already mounted, or another software may use it which could be identified for example by the help of the 'fuser' command. It's odd to me that that error message above claims that it's an NTFS volume when everything else tell me that it's an ext4 volume. The actual hard drive "Elements" is in fact an NTFS volume. Here's the output of a few commands and configuration files that may be of interest: $ fuser -a / /: 2120r 2159rc 2160rc 2172r 2178rc 2180rc 2188r 2191rc 2200rc 2203rc 2205rc 2206r 2211r 2212r 2214r 2220r 2228r 2234rc 2246rc 2249rc 2254rc 2260rc 2261r 2262r 2277rc 2287rc 2291rc 2311rc 2313rc 2332rc 2334rc 2339rc 2343rc 2344rc 2352rc 2372rc 2389rc 2422r 2490r 2496rc 2501rc 2566r 2573rc 2581rc 2589rc 2592r 2603r 2611rc 2613rc 2615rc 2678rc 2927r 2981r 3104rc 4156rc 4196rc 4206rc 4213rc 4240rc 4297rc 5032rc 7609r 7613r 7648r 9593rc 18829r 18833r 19776r $ sudo df -h Filesystem Size Used Avail Use% Mounted on /dev/sdb6 496G 366G 106G 78% / udev 2.0G 4.0K 2.0G 1% /dev tmpfs 791M 1.5M 790M 1% /run none 5.0M 0 5.0M 0% /run/lock none 2.0G 672K 2.0G 1% /run/shm /dev/sda1 932G 312G 620G 34% /media/Elements /home/solderblob/.Private 496G 366G 106G 78% /home/solderblob /dev/sdb2 188G 100G 88G 54% /media/A2B24EACB24E852F /dev/sdb1 100M 25M 76M 25% /media/System Reserved $ sudo fdisk -l Disk /dev/sda: 1000.2 GB, 1000204886016 bytes 255 heads, 63 sectors/track, 121601 cylinders, total 1953525168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00093cab Device Boot Start End Blocks Id System /dev/sda1 2048 1953519615 976758784 7 HPFS/NTFS/exFAT Disk /dev/sdb: 750.2 GB, 750156374016 bytes 255 heads, 63 sectors/track, 91201 cylinders, total 1465149168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x000e8d9b Device Boot Start End Blocks Id System /dev/sdb1 * 2048 206847 102400 7 HPFS/NTFS/exFAT /dev/sdb2 206848 392378768 196085960+ 7 HPFS/NTFS/exFAT /dev/sdb3 392380414 1465147391 536383489 5 Extended /dev/sdb5 1456762880 1465147391 4192256 82 Linux swap / Solaris /dev/sdb6 392380416 1448374271 527996928 83 Linux /dev/sdb7 1448376320 1456758783 4191232 82 Linux swap / Solaris Partition table entries are not in disk order $ cat /etc/fstab # <file system> <mount point> <type> <options> <dump> <pass> UUID=77039a2a-83d4-47a1-8a8c-a2ec4e4dfd0e / ext4 defaults 0 1 UUID=F6549CC4549C88CF /media/Elements ntfs-3g users 0 0 $ sudo blkid /dev/sda1: LABEL="Elements" UUID="F6549CC4549C88CF" TYPE="ntfs" /dev/sdb1: LABEL="System Reserved" UUID="5CDE130FDE12E156" TYPE="ntfs" /dev/sdb2: UUID="A2B24EACB24E852F" TYPE="ntfs" /dev/sdb6: UUID="77039a2a-83d4-47a1-8a8c-a2ec4e4dfd0e" TYPE="ext4" $ sudo blkid -c /dev/null (appears to be exactly the same as above) /dev/sda1: LABEL="Elements" UUID="F6549CC4549C88CF" TYPE="ntfs" /dev/sdb1: LABEL="System Reserved" UUID="5CDE130FDE12E156" TYPE="ntfs" /dev/sdb2: UUID="A2B24EACB24E852F" TYPE="ntfs" /dev/sdb6: UUID="77039a2a-83d4-47a1-8a8c-a2ec4e4dfd0e" TYPE="ext4" $ mount /dev/sdb6 on / type ext4 (rw) proc on /proc type proc (rw,noexec,nosuid,nodev) sysfs on /sys type sysfs (rw,noexec,nosuid,nodev) none on /sys/fs/fuse/connections type fusectl (rw) none on /sys/kernel/debug type debugfs (rw) none on /sys/kernel/security type securityfs (rw) udev on /dev type devtmpfs (rw,mode=0755) devpts on /dev/pts type devpts (rw,noexec,nosuid,gid=5,mode=0620) tmpfs on /run type tmpfs (rw,noexec,nosuid,size=10%,mode=0755) none on /run/lock type tmpfs (rw,noexec,nosuid,nodev,size=5242880) none on /run/shm type tmpfs (rw,nosuid,nodev) /dev/sda1 on /media/Elements type fuseblk (rw,noexec,nosuid,nodev,allow_other,blksize=4096) binfmt_misc on /proc/sys/fs/binfmt_misc type binfmt_misc (rw,noexec,nosuid,nodev) /home/solderblob/.Private on /home/solderblob type ecryptfs (ecryptfs_check_dev_ruid,ecryptfs_cipher=aes,ecryptfs_key_bytes=16,ecryptfs_unlink_sigs,ecryptfs_sig=76a47b0175afa48d,ecryptfs_fnek_sig=391b2d8b155215f7) gvfs-fuse-daemon on /home/solderblob/.gvfs type fuse.gvfs-fuse-daemon (rw,nosuid,nodev,user=solderblob) /dev/sdb2 on /media/A2B24EACB24E852F type fuseblk (rw,nosuid,nodev,allow_other,default_permissions,blksize=4096) /dev/sdb1 on /media/System Reserved type fuseblk (rw,nosuid,nodev,allow_other,default_permissions,blksize=4096) $ ls -a . A2B24EACB24E852F Ubuntu 12.04.1 LTS amd64 .. Elements System Reserved $ cat /proc/mounts rootfs / rootfs rw 0 0 sysfs /sys sysfs rw,nosuid,nodev,noexec,relatime 0 0 proc /proc proc rw,nosuid,nodev,noexec,relatime 0 0 udev /dev devtmpfs rw,relatime,size=2013000k,nr_inodes=503250,mode=755 0 0 devpts /dev/pts devpts rw,nosuid,noexec,relatime,gid=5,mode=620,ptmxmode=000 0 0 tmpfs /run tmpfs rw,nosuid,relatime,size=809872k,mode=755 0 0 /dev/disk/by-uuid/77039a2a-83d4-47a1-8a8c-a2ec4e4dfd0e / ext4 rw,relatime,user_xattr,acl,barrier=1,data=ordered 0 0 none /sys/fs/fuse/connections fusectl rw,relatime 0 0 none /sys/kernel/debug debugfs rw,relatime 0 0 none /sys/kernel/security securityfs rw,relatime 0 0 none /run/lock tmpfs rw,nosuid,nodev,noexec,relatime,size=5120k 0 0 none /run/shm tmpfs rw,nosuid,nodev,relatime 0 0 /dev/sda1 /media/Elements fuseblk rw,nosuid,nodev,noexec,relatime,user_id=0,group_id=0,allow_other,blksize=4096 0 0 binfmt_misc /proc/sys/fs/binfmt_misc binfmt_misc rw,nosuid,nodev,noexec,relatime 0 0 /home/solderblob/.Private /home/solderblob ecryptfs rw,relatime,ecryptfs_fnek_sig=391b2d8b155215f7,ecryptfs_sig=76a47b0175afa48d,ecryptfs_cipher=aes,ecryptfs_key_bytes=16,ecryptfs_unlink_sigs 0 0 gvfs-fuse-daemon /home/solderblob/.gvfs fuse.gvfs-fuse-daemon rw,nosuid,nodev,relatime,user_id=1000,group_id=1000 0 0 /dev/sdb2 /media/A2B24EACB24E852F fuseblk rw,nosuid,nodev,relatime,user_id=0,group_id=0,default_permissions,allow_other,blksize=4096 0 0 /dev/sdb1 /media/System\040Reserved fuseblk rw,nosuid,nodev,relatime,user_id=0,group_id=0,default_permissions,allow_other,blksize=4096 0 0 gvfs-fuse-daemon /root/.gvfs fuse.gvfs-fuse-daemon rw,nosuid,nodev,relatime,user_id=0,group_id=0 0 0 $ fsck fsck from util-linux 2.20.1 e2fsck 1.42 (29-Nov-2011) /dev/sdb6 is mounted. WARNING!!! The filesystem is mounted. If you continue you ***WILL*** cause ***SEVERE*** filesystem damage. Do you really want to continue<n>? no check aborted.

  Read the article

• Troubleshooting major performance issue: Is culprit Intel RST, Hard drive, or something else?

  - by Sean Killeen

  The Setup I have the following components that come into play in this situation: ASUS P8Z68 V/PRO motherboard a RAID1 configuration (1x 1TB drive, 1 x 2TB drive -- I explain below), accelerated with an SSD using Intel's RST software, and 1 TB drive standing by as a spare. Core i7 2600k 32 GB RAM Windows 8.1 This box was designed to be beast, and until just recently, was very good at being just that. What's Happening The system has slowed to a crawl whenever it touches the disk. Things appear to work at normal speed when dealing with memory. For example, typing this is fine, but saving it to disk from notepad gave me a 5-7 second pause when clicking save. The disks appear to be at 100% all the time (e.g. the light on the disk access on the PC is solidly on -- not even any flashing) In ProcExp it appears that the disk is barely being utilized at all: Intel RST reports that everything is fine: Other Details Prior to this happening, RST had reported that my drives were failing (one went bad, one was throwing SMART events). This made sense; they were at the tail end of their warranty and the PC is on almost all the time. I RMA'd the drives via Seagate. In the meantime, I'd purchased a 2TB drive because I didn't realize that the 1TB drives were under warranty. I figured I'd replace the other 1 TB drive with another 2 TB when it died but then discovered the warranty. AFAIK, I haven't done any major updates since 8.1 and it worked fine after those. Question(s) How can I troubleshoot this? What is the best way to try to figure out why disks are being maxed out despite the OS reporting barely any disk usage and that everything is OK? Given the failures, etc. that I describe above, is it possible that the problem could be the I/O on the motherboard itself? If so, how would I even be able to diagnose it? I'm betting the drives that Seagate gave me are refurbished (didn't think to look; that's dumb). Is it possible that the same model drive, refurbished, could somehow cause this? In terms of how RAID1 works, is it possible that one drive is "falling behind" somehow, and that the RAID1 is constantly trying to fix the mirroring? If so, this seems like Intel RST would report on it, but I wanted to consider it as an option.

  Read the article

• How to Create a bootable Ubuntu USB flash drive from terminal

  - by Avinash Raj

  Is there any possibility to create a Ubuntu USB flash drive from terminal without using any third-party applications like YUMI,Unetbootin,etc. I tried to create a bootable ubuntu flash drive with dd method, sudo umount /dev/sdb sudo dd if=/path/to/ubuntu.iso of=/dev/sdb bs=1M It create files on the USB disk,but when i try to boot the usb disk it says Operating System Not Found error. Any help will be appreciated!

  Read the article

• MySQL Memory usage

  - by Rob Stevenson-Leggett

  Our MySQL server seems to be using a lot of memory. I've tried looking for slow queries and queries with no index and have halved the peak CPU usage and Apache memory usage but the MySQL memory stays constantly at 2.2GB (~51% of available memory on the server). Here's the graph from Plesk. Running top in the SSH window shows the same figures. Does anyone have any ideas on why the memory usage is constant like this and not peaks and troughs with usage of the app? Here's the output of the MySQL Tuning Primer script: -- MYSQL PERFORMANCE TUNING PRIMER -- - By: Matthew Montgomery - MySQL Version 5.0.77-log x86_64 Uptime = 1 days 14 hrs 4 min 21 sec Avg. qps = 22 Total Questions = 3059456 Threads Connected = 13 Warning: Server has not been running for at least 48hrs. It may not be safe to use these recommendations To find out more information on how each of these runtime variables effects performance visit: http://dev.mysql.com/doc/refman/5.0/en/server-system-variables.html Visit http://www.mysql.com/products/enterprise/advisors.html for info about MySQL's Enterprise Monitoring and Advisory Service SLOW QUERIES The slow query log is enabled. Current long_query_time = 1 sec. You have 6 out of 3059477 that take longer than 1 sec. to complete Your long_query_time seems to be fine BINARY UPDATE LOG The binary update log is NOT enabled. You will not be able to do point in time recovery See http://dev.mysql.com/doc/refman/5.0/en/point-in-time-recovery.html WORKER THREADS Current thread_cache_size = 0 Current threads_cached = 0 Current threads_per_sec = 2 Historic threads_per_sec = 0 Threads created per/sec are overrunning threads cached You should raise thread_cache_size MAX CONNECTIONS Current max_connections = 100 Current threads_connected = 14 Historic max_used_connections = 20 The number of used connections is 20% of the configured maximum. Your max_connections variable seems to be fine. INNODB STATUS Current InnoDB index space = 6 M Current InnoDB data space = 18 M Current InnoDB buffer pool free = 0 % Current innodb_buffer_pool_size = 8 M Depending on how much space your innodb indexes take up it may be safe to increase this value to up to 2 / 3 of total system memory MEMORY USAGE Max Memory Ever Allocated : 2.07 G Configured Max Per-thread Buffers : 274 M Configured Max Global Buffers : 2.01 G Configured Max Memory Limit : 2.28 G Physical Memory : 3.84 G Max memory limit seem to be within acceptable norms KEY BUFFER Current MyISAM index space = 4 M Current key_buffer_size = 7 M Key cache miss rate is 1 : 40 Key buffer free ratio = 81 % Your key_buffer_size seems to be fine QUERY CACHE Query cache is supported but not enabled Perhaps you should set the query_cache_size SORT OPERATIONS Current sort_buffer_size = 2 M Current read_rnd_buffer_size = 256 K Sort buffer seems to be fine JOINS Current join_buffer_size = 132.00 K You have had 16 queries where a join could not use an index properly You should enable "log-queries-not-using-indexes" Then look for non indexed joins in the slow query log. If you are unable to optimize your queries you may want to increase your join_buffer_size to accommodate larger joins in one pass. Note! This script will still suggest raising the join_buffer_size when ANY joins not using indexes are found. OPEN FILES LIMIT Current open_files_limit = 1024 files The open_files_limit should typically be set to at least 2x-3x that of table_cache if you have heavy MyISAM usage. Your open_files_limit value seems to be fine TABLE CACHE Current table_cache value = 64 tables You have a total of 426 tables You have 64 open tables. Current table_cache hit rate is 1% , while 100% of your table cache is in use You should probably increase your table_cache TEMP TABLES Current max_heap_table_size = 16 M Current tmp_table_size = 32 M Of 15134 temp tables, 9% were created on disk Effective in-memory tmp_table_size is limited to max_heap_table_size. Created disk tmp tables ratio seems fine TABLE SCANS Current read_buffer_size = 128 K Current table scan ratio = 2915 : 1 read_buffer_size seems to be fine TABLE LOCKING Current Lock Wait ratio = 1 : 142213 Your table locking seems to be fine The app is a facebook game with about 50-100 concurrent users. Thanks, Rob

  Read the article

• execute script with sudo after login

  - by Kalamalka Kid

  i need to execute the following commands AFTER login. sudo hdparm -y /dev/disk/by-uuid/443AFBAD7FE50945 sudo hdparm -y /dev/disk/by-uuid/7ABB49654B799D40 (trying to edit rc.local does not work nor does using hdparm.conf because as soon as I log in the disks start up again). I have tried numerous things like bash files and autossh entries in the startup applications with no luck because sudo is involved.

  Read the article

• The WaitForAll Roadshow

  - by adweigert

  OK, so I took for granted some imaginative uses of WaitForAll but lacking that, here is how I am using. First, I have a nice little class called Parallel that allows me to spin together a list of tasks (actions) and then use WaitForAll, so here it is, WaitForAll's 15 minutes of fame ... First Parallel that allows me to spin together several Action delegates to execute, well in parallel.   public static class Parallel { public static ParallelQuery Task(Action action) { return new Action[] { action }.AsParallel(); } public static ParallelQuery> Task(Action action) { return new Action[] { action }.AsParallel(); } public static ParallelQuery Task(this ParallelQuery actions, Action action) { var list = new List(actions); list.Add(action); return list.AsParallel(); } public static ParallelQuery> Task(this ParallelQuery> actions, Action action) { var list = new List>(actions); list.Add(action); return list.AsParallel(); } }   Next, this is an example usage from an app I'm working on that just is rendering some basic computer information via WMI and performance counters. The WMI calls can be expensive given the distance and link speed of some of the computers it will be trying to communicate with. This is the actual MVC action from my controller to return the data for an individual computer.  public PartialViewResult Detail(string computerName) { var computer = this.Computers.Get(computerName); var perf = Factory.GetInstance(); var detail = new ComputerDetailViewModel() { Computer = computer }; try { var work = Parallel .Task(delegate { // Win32_ComputerSystem var key = computer.Name + "_Win32_ComputerSystem"; var system = this.Cache.Get(key); if (system == null) { using (var impersonation = computer.ImpersonateElevatedIdentity()) { system = computer.GetWmiContext().GetInstances().Single(); } this.Cache.Set(key, system); } detail.TotalMemory = system.TotalPhysicalMemory; detail.Manufacturer = system.Manufacturer; detail.Model = system.Model; detail.NumberOfProcessors = system.NumberOfProcessors; }) .Task(delegate { // Win32_OperatingSystem var key = computer.Name + "_Win32_OperatingSystem"; var os = this.Cache.Get(key); if (os == null) { using (var impersonation = computer.ImpersonateElevatedIdentity()) { os = computer.GetWmiContext().GetInstances().Single(); } this.Cache.Set(key, os); } detail.OperatingSystem = os.Caption; detail.OSVersion = os.Version; }) // Performance Counters .Task(delegate { using (var impersonation = computer.ImpersonateElevatedIdentity()) { detail.AvailableBytes = perf.GetSample(computer, "Memory", "Available Bytes"); } }) .Task(delegate { using (var impersonation = computer.ImpersonateElevatedIdentity()) { detail.TotalProcessorUtilization = perf.GetValue(computer, "Processor", "% Processor Time", "_Total"); } }).WithExecutionMode(ParallelExecutionMode.ForceParallelism); if (!work.WaitForAll(TimeSpan.FromSeconds(15), task => task())) { return PartialView("Timeout"); } } catch (Exception ex) { this.LogException(ex); return PartialView("Error.ascx"); } return PartialView(detail); }

  Read the article

• Free RAM disappears - Memory leak?

  - by Izzy

  On a fresh started system, free reports about 1.5G used RAM (8G RAM alltogether, Ubuntu 12.04 with lightdm and plasma desktop, one konsole window started). Having the apps running I use, it still consumes not more than 2G. However, having the system running for a couple of days, more and more of my free RAM disappears -- without showing up in the list of used apps: while smem --pie=name reports less than 20% used (and 80% being available), everything else says differently. free -m for example reports on about day 7: total used free shared buffers cached Mem: 7459 7013 446 0 178 997 -/+ buffers/cache: 5836 1623 Swap: 9536 296 9240 (so you can see, it's not the buffers or the cache). Today this finally ended with the system crashing completely: the windows manager being gone, apps "hanging in the air" (frameless) -- and a popup notifying me about "too many open files". Syslog reports: kernel: [856738.020829] VFS: file-max limit 752838 reached So I closed those applications I was able to close, and killed X using Ctrl-Alt-backspace. X tried to come up again after that with failsafeX, but was unable to do so as it could no longer detect its configuration. So I switched to a console using Ctrl-Alt-F2, captured all information I could think of (vmstat, free, smem, proc/meminfo, lsof, ps aux), and finally rebooted. X again came up with failsafeX; this time I told it to "recover from my backed-up configuration", then switched to a console and successfully used startx to bring up the graphical environment. I have no real clue to what is causing this issue -- though it must have to do either with X itself, or with some user processes running on X -- as after killing X, free -m output looked like this: total used free shared buffers cached Mem: 7459 2677 4781 0 62 419 -/+ buffers/cache: 2195 5263 Swap: 9536 59 9477 (~3.5GB being freed) -- to compare with the output after a fresh start: total used free shared buffers cached Mem: 7459 1483 5975 0 63 730 -/+ buffers/cache: 689 6769 Swap: 9536 0 9536 Two more helpful outputs are provided by memstat -u. Shortly before the crash: User Count Swap USS PSS RSS mail 1 0 200 207 616 whoopsie 1 764 740 817 2300 colord 1 3200 836 894 2156 root 62 70404 352996 382260 569920 izzy 80 177508 1465416 1519266 1851840 After having X killed: User Count Swap USS PSS RSS mail 1 0 184 188 356 izzy 1 1400 708 739 1080 whoopsie 1 848 668 826 1772 colord 1 3204 804 888 1728 root 62 54876 131708 149950 267860 And after a restart, back in X: User Count Swap USS PSS RSS mail 1 0 212 217 628 whoopsie 1 0 1536 1880 5096 colord 1 0 3740 4217 7936 root 54 0 148668 180911 345132 izzy 47 0 370928 437562 915056 Edit: Just added two graphs from my monitoring system. Interesting to see: everytime when there's a "jump" in memory consumption, CPU peaks as well. Just found this right now -- and it reminds me of another indicator pointing to X itself: Often when returning to my machine and unlocking the screen, I found something doing heavvy work on my CPU. Checking with top, it always turned out to be /usr/bin/X :0 -auth /var/run/lightdm/root/:0 -nolisten tcp vt7 -novtswitch -background none. So after this long explanation, finally my questions: What could be the possible causes? How can I better identify involved processes/applications? What steps could be taken to avoid this behaviour -- short from rebooting the machine all X days? I was running 8.04 (Hardy) for about 5 years on my old machine, never having experienced the like (always more than 100 days uptime, before rebooting for e.g. kernel updates). This now is a complete new machine with a fresh install of 8.04. In case it matters, some specs: AMD A4-3400 APU with Radeon(tm) HD Graphics, using the open-source ati/radeon driver (so no fglrx installed), 8GB RAM, WDC WD1002FAEX-0 hdd (1TB), Asus F1A75-V Evo mainboard. Ubuntu 12.04 64-bit with KDE4/Plasma. Apps usually open more or less permanently include Evolution, Firefox, konsole (with Midnight Commander running inside, about 4 tabs), and LibreOffice -- plus occasionally Calibre, Gimp and Moneyplex (banking software I'm already using for almost 20 years now, in a version which did fine on Hardy).

  Read the article

• How to create an EFI System Partition?

  - by Alex Popov

  TL; DR How do I create an EFI system partition from scratch? How do I put the EFI firmware on it onces it is created? Long version I hava Toshiba T430 laptop. I received it with Windows 7 installed (but I think originally it has shipped with Windows 8). I installed Ubuntu on it, but deleted some partitions on the disk so that I ended up wiping out the Windows and only having Ubuntu. Among the deleted partitions was the EFI System partition. I discovered that Ubuntu now boots in Legacy mode (and not UEFI). I am trying to follow this guide on converting my Ubuntu installation from Legacy to UEFI. The problem - since there is no EFI partition whenever I choose from BIOS to boot using UEFI I cannot boot. That counts not only for the harddrive, but usb and DVD as well. I think this is logical - it expects an EFI partition and since it can't find it, it cannot continue booting futher, be it from HDD or DVD. So how do I recreate the EFI partition? The guide above says: Creating an EFI partition If you are manually partitioning your disk in the Ubuntu installer, you need to make sure you have an EFI partition set up. If your disk already contains an EFI partition (eg if your computer had Windows8 preinstalled), it can be used for Ubuntu too. Do not format it. It is strongly recommended to have only 1 EFI partition per disk. An EFI partition can be created via a recent version of GParted (the Gparted version included in the 12.04 disk is OK), and must have the following attributes: Mount point: /boot/efi (remark: no need to set this mount point when using the manual partitioning, the Ubuntu installer will detect it automatically) Size: minimum 100Mib. 200MiB recommended. Type: FAT32 Other: needs a "boot" flag. I had some trouble creating this partition: I boot from a live Ubuntu DVD, open GParted, create a 200MB partition and format it to FAT32. In GParted I cannot set the mount point and thus cannot set the bootflag. I didn't set the mount point in /etc/fstab since it's a live CD and fstab looked quite differently from what I expected compared to a normal boot. Anyway, I just didn't know what values to set. I booted again via the live DVD and then chose to install Ubuntu. I then created a partition with the mentioned criteria - mount point, 200MB, FAT32, boot flag. However, I continue to have this problem and I suppose it's because on that partition there is no EFI firmware, it's just an empty partition, which is suitable to have EFI firmware. So again, how do I create an EFI partition, which has the EFI software, so that the laptop can once again boot in UEFI mode?

  Read the article

• xen-create-image does not create inird or initramfs image and domU does not starts with system image

  - by user219372

  I have Fedora 19 as Dom0. To create image I run # xen-create-image --hostname=debian-wheezy --memory=512Mb --dhcp --size=20Gb --swap=512Mb --dir=/xen --arch=amd64 --dist=wheezy After generation finished I start vm and see: # xl create /etc/xen/debian-wheezy.cfg Parsing config from /etc/xen/debian-wheezy.cfg libxl: error: libxl_dom.c:409:libxl__build_pv: xc_dom_ramdisk_file failed: No such file or directory libxl: error: libxl_create.c:919:domcreate_rebuild_done: cannot (re-)build domain: -3 In the /etc/xen/debian-wheezy.cfg i have # # Kernel + memory size # kernel = '/boot/vmlinuz-3.11.2-201.fc19.x86_64' ramdisk = '/boot/initrd.img-3.11.2-201.fc19.x86_64' and ls -1 /boot/*201* shows /boot/config-3.11.2-201.fc19.x86_64 /boot/initramfs-3.11.2-201.fc19.x86_64.img /boot/System.map-3.11.2-201.fc19.x86_64 /boot/vmlinuz-3.11.2-201.fc19.x86_64 Then if I fix ramdisk directive in .cfg file to /boot/initramfs-3.11.2-201.fc19.x86_64.img vm will start but os inside will not boot. In a tail of xl console I get [ OK ] Reached target Basic System. dracut-initqueue[130]: Warning: Could not boot. dracut-initqueue[130]: Warning: /dev/disk/by-uuid/085883ad-73ca-45cc-8bc5-e6249f869b26 does not exist dracut-initqueue[130]: Warning: /dev/fedora/root does not exist dracut-initqueue[130]: Warning: /dev/fedora/swap does not exist dracut-initqueue[130]: Warning: /dev/mapper/fedora-root does not exist dracut-initqueue[130]: Warning: /dev/mapper/fedora-swap does not exist dracut-initqueue[130]: Warning: /dev/xvda2 does not exist Starting Dracut Emergency Shell... Warning: /dev/disk/by-uuid/085883ad-73ca-45cc-8bc5-e6249f869b26 does not exist Warning: /dev/fedora/root does not exist Warning: /dev/fedora/swap does not exist Warning: /dev/mapper/fedora-root does not exist Warning: /dev/mapper/fedora-swap does not exist Warning: /dev/xvda2 does not exist Generating "/run/initramfs/sosreport.txt" Entering emergency mode. Exit the shell to continue. Type "journalctl" to view system logs. You might want to save "/run/initramfs/sosreport.txt" to a USB stick or /boot after mounting them and attach it to a bug report. dracut:/# .img files in /xen/domains/debian-wheezy exists and listed in disk section of debian-wheezy.cfg So what should i do? Update: I've found that xl does not mount images. In debian-wheezy.cfg I have that: root = '/dev/xvda2 ro' disk = [ 'file:/xen/domains/debian-wheezy/disk.img,xvda2,w', 'file:/xen/domains/debian-wheeze/swap.img,xvda1,w', ] And there is no /dev/xvda* or /dev/sda* or /dev/hda* files in VM.

  Read the article

• Eclipse Indigo very slow on Kubuntu 12.04

  - by herom

  hello fellow ubuntu users! I have a really big problem with my Eclipse Indigo running on Kubuntu 12.04 32bit, Dell Vostro 3500, Intel(R) Core(TM) i5 CPU M480 @ 2.67 (as cat /proc/cpuinfo said). It has 4GB RAM. cat /proc/cpuinfo brings up the following: processor : 0 vendor_id : GenuineIntel cpu family : 6 model : 37 model name : Intel(R) Core(TM) i5 CPU M 480 @ 2.67GHz stepping : 5 microcode : 0x2 cpu MHz : 1197.000 cache size : 3072 KB physical id : 0 siblings : 4 core id : 0 cpu cores : 2 apicid : 0 initial apicid : 0 fdiv_bug : no hlt_bug : no f00f_bug : no coma_bug : no fpu : yes fpu_exception : yes cpuid level : 11 wp : yes flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm pbe nx rdtscp lm constant_tsc arch_perfmon pebs bts xtopology nonstop_tsc aperfmperf pni dtes64 monitor ds_cpl vmx est tm2 ssse3 cx16 xtpr pdcm pcid sse4_1 sse4_2 popcnt lahf_lm ida arat dts tpr_shadow vnmi flexpriority ept vpid bogomips : 5319.85 clflush size : 64 cache_alignment : 64 address sizes : 36 bits physical, 48 bits virtual power management: processor : 1 vendor_id : GenuineIntel cpu family : 6 model : 37 model name : Intel(R) Core(TM) i5 CPU M 480 @ 2.67GHz stepping : 5 microcode : 0x2 cpu MHz : 1197.000 cache size : 3072 KB physical id : 0 siblings : 4 core id : 2 cpu cores : 2 apicid : 4 initial apicid : 4 fdiv_bug : no hlt_bug : no f00f_bug : no coma_bug : no fpu : yes fpu_exception : yes cpuid level : 11 wp : yes flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm pbe nx rdtscp lm constant_tsc arch_perfmon pebs bts xtopology nonstop_tsc aperfmperf pni dtes64 monitor ds_cpl vmx est tm2 ssse3 cx16 xtpr pdcm pcid sse4_1 sse4_2 popcnt lahf_lm ida arat dts tpr_shadow vnmi flexpriority ept vpid bogomips : 5319.88 clflush size : 64 cache_alignment : 64 address sizes : 36 bits physical, 48 bits virtual power management: processor : 2 vendor_id : GenuineIntel cpu family : 6 model : 37 model name : Intel(R) Core(TM) i5 CPU M 480 @ 2.67GHz stepping : 5 microcode : 0x2 cpu MHz : 1197.000 cache size : 3072 KB physical id : 0 siblings : 4 core id : 0 cpu cores : 2 apicid : 1 initial apicid : 1 fdiv_bug : no hlt_bug : no f00f_bug : no coma_bug : no fpu : yes fpu_exception : yes cpuid level : 11 wp : yes flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm pbe nx rdtscp lm constant_tsc arch_perfmon pebs bts xtopology nonstop_tsc aperfmperf pni dtes64 monitor ds_cpl vmx est tm2 ssse3 cx16 xtpr pdcm pcid sse4_1 sse4_2 popcnt lahf_lm ida arat dts tpr_shadow vnmi flexpriority ept vpid bogomips : 5319.88 clflush size : 64 cache_alignment : 64 address sizes : 36 bits physical, 48 bits virtual power management: processor : 3 vendor_id : GenuineIntel cpu family : 6 model : 37 model name : Intel(R) Core(TM) i5 CPU M 480 @ 2.67GHz stepping : 5 microcode : 0x2 cpu MHz : 1197.000 cache size : 3072 KB physical id : 0 siblings : 4 core id : 2 cpu cores : 2 apicid : 5 initial apicid : 5 fdiv_bug : no hlt_bug : no f00f_bug : no coma_bug : no fpu : yes fpu_exception : yes cpuid level : 11 wp : yes flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm pbe nx rdtscp lm constant_tsc arch_perfmon pebs bts xtopology nonstop_tsc aperfmperf pni dtes64 monitor ds_cpl vmx est tm2 ssse3 cx16 xtpr pdcm pcid sse4_1 sse4_2 popcnt lahf_lm ida arat dts tpr_shadow vnmi flexpriority ept vpid bogomips : 5319.88 clflush size : 64 cache_alignment : 64 address sizes : 36 bits physical, 48 bits virtual power management: java -version brings the following: java version "1.7.0_04" Java(TM) SE Runtime Environment (build 1.7.0_04-b20) Java HotSpot(TM) Server VM (build 23.0-b21, mixed mode) it's the Oracle Java, not OpenJDK. I try to develop an Android application for GoogleTV and Eclipse is this slow, that it can't follow my typing (extreme lagging!!), but this issue makes it almost impossible! here is my eclipse.ini file: -startup plugins/org.eclipse.equinox.launcher_1.2.0.v20110502.jar --launcher.library plugins/org.eclipse.equinox.launcher.gtk.linux.x86_1.1.100.v20110505 -product org.eclipse.epp.package.java.product --launcher.defaultAction openFile -showsplash org.eclipse.platform --launcher.XXMaxPermSize 512m --launcher.defaultAction openFile -vmargs -Dosgi.requiredJavaVersion=1.5 -Declipse.p2.unsignedPolicy=allow -Xms256m -Xmx512m -Xss4m -XX:PermSize=128m -XX:MaxPermSize=384m -XX:CompileThreshold=5 -XX:MaxGCPauseMillis=10 -XX:MaxHeapFreeRatio=70 -XX:+CMSIncrementalPacing -XX:+UnlockExperimentalVMOptions -XX:+UseG1GC -XX:+UseFastAccessorMethods -XX:ReservedCodeCacheSize=64m -Dcom.sun.management.jmxremote has anybody faced the same problems? can anybody help me on this problem? it's really urgent as I'm sitting here at my company and am not able to do anything productive...

  Read the article

< Previous Page | 167 168 169 170 171 172 173 174 175 176 177 178  | Next Page >