Search Results

Search found 5092 results on 204 pages for 'kernel tracker'.

Page 171/204 | < Previous Page | 167 168 169 170 171 172 173 174 175 176 177 178  | Next Page >

• fail2ban log parsing too slow on Raspberry Pi - options? [migrated]

  - by Gordon Morehouse

  I'm running fail2ban on a Raspberry Pi at 950MHz which I cannot overclock further. The Pi is occasionally subject to SYN floods on particular ports. I've set up iptables to throttle the rate of SYNs on the port of interest; when the throttle limits are exceeded, hosts which send SYNs are dropped into the REJECT chain and the particular SYN packet which exceeded the limit is logged. fail2ban then watches for these logged SYNs and, after seeing a few, temporarily bans the host for a short time (this is a transient issue in the app I'm working with). The problem is that the SYN floods can occasionally reach rates which are too fast for fail2ban to keep up with; I'll see 20-40 log messages per second, and eventually fail2ban falls behind and becomes ineffective. To add insult to injury, it continues consuming a LOT of CPU as it tries to catch up. I have verified that DROP chained packets from hosts already banned by fail2ban are not logged, and thus do not add to its load. What are my options here? I have a few ideas, but no clear path forward. Could I make the log-parse regex "easier" so it takes fewer cycles? Would using iptables --log-prefix to put a token near the start of the log message, and/or otherwise simplifying/altering the fail2ban regex help? Here is the current fail2ban config line containing a regex: failregex = kernel:.*?SRC=(?:::f{4,6}:)?(?P<host>[\w\-.^_]+) DST.*?SYN Is there a faster way for fail2ban to watch for the packets exceeding the limits than parsing kern.log? Could fail2ban be run under PyPy instead of CPython with minimal nonstandard wizardry (the OS is Raspbian 7, so, mostly Debian 7)? Is there something better than fail2ban that I could use to watch for the packets which exceed the SYN limits, and after N exceeds in X seconds, temporarily put the offending IP into the iptables DROP bucket, and take it out when the ban timer expires? Again, I'd vastly prefer a solution that uses as much software available in Debian as possible, though I can build Debian packages in a pinch.

  Read the article

• Secondary IP (eth0:0) acts like main server IP

  - by George Tasioulis

  I have a CentOS server, configured with 4 consecutive IPs: eth0 5.x.x.251 eth0:0 5.x.x.252 eth0:1 5.x.x.253 eth0:2 5.x.x.254 The problem is that all traffic goes out to the internet with eth0:0 (5.x.x.252) as the source IP, instead of eth0. # curl ifconfig.me 5.x.x.252 How can I fix this, so that all traffic goes out via eth0, ie my main IP? PS: My server is VPS running on a Xen dom0, the latter being configured in routed mode networking. Thanks in advance! Server configuration # ifconfig eth0 Link encap:Ethernet HWaddr 00:x:x:x:x:AE inet addr:5.x.x.251 Bcast:5.x.x.255 Mask:255.255.255.255 inet6 addr: fe80::x:x:x:x/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:14675569 errors:0 dropped:0 overruns:0 frame:0 TX packets:9463227 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:4122016502 (3.8 GiB) TX bytes:25959110751 (24.1 GiB) Interrupt:23 eth0:0 Link encap:Ethernet HWaddr 00:x:x:x:x:AE inet addr:5.x.x.252 Bcast:5.x.x.255 Mask:255.255.255.224 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Interrupt:23 eth0:1 Link encap:Ethernet HWaddr 00:x:x:x:x:AE inet addr:5.x.x.253 Bcast:5.x.x.255 Mask:255.255.255.224 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Interrupt:23 eth0:2 Link encap:Ethernet HWaddr 00:x:x:x:x:AE inet addr:5.x.x.254 Bcast:5.x.x.255 Mask:255.255.255.224 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Interrupt:23 # cat /etc/hosts 127.0.0.1 localhost.localdomain localhost 5.x.x.251 [fqdn] [hostname] # cat ifcfg-eth0 DEVICE=eth0 BOOTPROTO=static ONBOOT=yes IPADDR=5.x.x.251 NETMASK=255.255.255.224 SCOPE="peer 5.x.y.82" # cat ifcfg-eth0:0 DEVICE=eth0:0 BOOTPROTO=static ONBOOT=yes IPADDR=5.x.x.252 NETMASK=255.255.255.224 # cat route-eth0 ADDRESS0=0.0.0.0 NETMASK0=0.0.0.0 GATEWAY0=5.x.y.82 # netstat -rn Kernel IP routing table Destination Gateway Genmask Flags MSS Window irtt Iface 5.x.y.82 0.0.0.0 255.255.255.255 UH 0 0 0 eth0 5.x.x.224 0.0.0.0 255.255.255.224 U 0 0 0 eth0 169.254.0.0 0.0.0.0 255.255.0.0 U 0 0 0 eth0 0.0.0.0 5.x.y.82 0.0.0.0 UG 0 0 0 eth0

  Read the article

• Get Python to raise MemoryError instead of eating all my disk space

  - by asmeurer

  If I run a Python program with a memory leak, I would normally expect the program to eventually die with MemoryError. But instead, what happens is that all the virtual memory is used until my disk runs out of space. I am running Mac OS X 10.8 on a retina MacBook Pro. My computer generally has between 10GB to 20GB free. Mac OS X is smart enough to not die completely when the disk runs out of space (rather, it gives me a dialog letting me force quit my GUI programs). Is there a way to make Python just die when it runs out of real memory, or some reasonable amount of virtual memory? This is what happens on Linux, as far as I can tell. I guess Mac OS X is more generous than Linux with virtual memory (the fact that I have an SSD might be part of this; I don't know just how smart OS X is with this stuff). Maybe there's a way to tell the Mac OS X kernel to never use so much virtual memory that leaves less than, say, 5 GB free on the hard drive?

  Read the article

• Ubuntu 13.10 on Acer V5-472 with HD 4000

  - by Hyperboreus

  I have an Acer V5-472 with intel HD4000 graphics chipset and a built-in 1366*768 display. I have installed ubuntu 13.10 amd64 in legacy boot mode with an external monitor. Installation showed no problems, I can boot from HDD and log into my system. The internal display doesn't work and I have to use an external monitor. I have tried the following (found in other threads) to no avail: Setting grub option "acpi_backlight=vendor" or "acpi_osi=Linux" or both. Installing the intel HD drivers for Linux from their homepage. Running in circles, screaming and shouting. The internal display lights up (I can change the brightness with Fn-Left and Fn-Right) but that's all. When I boot, I get a purple splash screen and from then only the external monitor works. I read somewhere that this might be a problem with kernel 3.11? Has anybody ubuntu running on an Acer V5-472? Should I change ubuntu version or use 32-bit instead? In general, how can I get the internal display to work? Edit: The settings-display dialogue shows the internal display correctly with supported resolution of 1366.

  Read the article

• multiple ip for a server not reachable

  - by andrewk

  FYI: I've read everything on Serverfault related to this question and have faced a different issue. Simply put, I've got one server (apache2) with couple of sites on it. It currently has 1 ip. I'm trying to assign/add another ip to that server, so I can give each site a different ip for ssl purposes. I am not lucking out. The new ip simply is unreachable, I've pinged it. This is what I've got below, what am I doing wrong. auto lo iface lo inet loopback auto eth0 eth0:0 eth0:1 iface eth0 inet static address 70.116.5.244 netmask 255.255.255.0 gateway 70.116.5.1 #THE NEW IP iface eth0:0 inet static address 26.175.217.102 netmask 255.255.255.0 #PRIVATE IP iface eth0:1 inet static address 192.168.158.88 netmask 255.255.128.0 NOTE: THESE IP'S ARE TWEAKED BUT RELATIVE I've read many questions here 90% similar to this but most actually have the IP respond, not this case. Thanks netstar -r output Kernel IP routing table Destination Gateway Genmask Flags MSS Window irtt Iface default gw-u6.linode.co 0.0.0.0 UG 0 0 0 eth0 70.116.5.0 * 255.255.255.0 U 0 0 0 eth0 26.175.217.0 * 255.255.255.0 U 0 0 0 eth0 192.168.128.0 * 255.255.128.0 U 0 0 0 eth0

  Read the article

• Change the default route without affecting existing TCP connections

  - by Patrick Horn

  Let's say I have two public network addresses on my server: one NAT through an ISP (192.168.99.0/24), and a VPN through a different ISP (192.168.1.0/24), already configured with a per-host route to the VPN server through my ISP. Here is my initial routing table. I am currently routing through my ISP on subnet 192.168.99.0/24. $ route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 0.0.0.0 192.168.99.1 0.0.0.0 UG 0 0 0 eth1 55.66.77.88 192.168.99.1 255.255.255.255 UGH 0 0 0 eth1 192.168.99.0 0.0.0.0 255.255.255.0 U 0 0 0 eth1 192.168.1.0 0.0.0.0 255.255.255.0 U 0 0 0 tap0 Now, I want new TCP connections to switch to my 192.168.1.0/24 so I type the following: $ route add -net 0.0.0.0 gw 192.168.1.1 dev tap0 When I do this, it causes some long-standing TCP connections to hang. Is there a way to I safely change the default interface for new connections, while allowing existing TCP connections to use the old route (i.e. do I need enable some sort of stateful routing table)? I am okay with a solution that only works with established TCP connections, and I don't care how hacky it is. For example, if there is a way to add temporary iptables rules for existing connections to force them over the old route. But there has to be some way to do this. EDIT: Just a note about a simple "route add -host ... " for existing connections: this solution would work if I am fine with leaving a subset of IPs on the old interface. However, in my application, this actually doesn't solve my problem because I want to allow new connections to come on the new interface even if they have the same source IP. I'm now looking at using the "ip route" command to set source-based routing rules.

  Read the article

• Debian amd64 on Dell Studio 540 reboot hangs

  - by Shcheklein

  Hi, I have Dell Studio 540 desktop and Debian Lenny installed on it: 2.6.26-2-amd64 #1 SMP Tue Mar 9 22:29:32 UTC 2010 x86_64 GNU/Linux The problem is that I can't reboot it. It just hangs after "Will now restart" message. I've already tried: reboot=b, reboot=a, reboot=h kernel options. Nothing helps. Additional info (I can provide any other information): dmidecode System Information Manufacturer: Dell Inc. Product Name: Studio 540 lspci 00:00.0 Host bridge: Intel Corporation 4 Series Chipset DRAM Controller (rev 03) 00:02.0 VGA compatible controller: Intel Corporation 4 Series Chipset Integrated Graphics Controller (rev 03) 00:02.1 Display controller: Intel Corporation 4 Series Chipset Integrated Graphics Controller (rev 03) 00:1a.0 USB Controller: Intel Corporation 82801JI (ICH10 Family) USB UHCI Controller #4 00:1a.1 USB Controller: Intel Corporation 82801JI (ICH10 Family) USB UHCI Controller #5 00:1a.2 USB Controller: Intel Corporation 82801JI (ICH10 Family) USB UHCI Controller #6 00:1a.7 USB Controller: Intel Corporation 82801JI (ICH10 Family) USB2 EHCI Controller #2 00:1b.0 Audio device: Intel Corporation 82801JI (ICH10 Family) HD Audio Controller 00:1c.0 PCI bridge: Intel Corporation 82801JI (ICH10 Family) PCI Express Port 1 00:1c.2 PCI bridge: Intel Corporation 82801JI (ICH10 Family) PCI Express Port 3 00:1c.5 PCI bridge: Intel Corporation 82801JI (ICH10 Family) PCI Express Port 6 00:1d.0 USB Controller: Intel Corporation 82801JI (ICH10 Family) USB UHCI Controller #1 00:1d.1 USB Controller: Intel Corporation 82801JI (ICH10 Family) USB UHCI Controller #2 00:1d.2 USB Controller: Intel Corporation 82801JI (ICH10 Family) USB UHCI Controller #3 00:1d.7 USB Controller: Intel Corporation 82801JI (ICH10 Family) USB2 EHCI Controller #1 00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev 90) 00:1f.0 ISA bridge: Intel Corporation 82801JIR (ICH10R) LPC Interface Controller 00:1f.2 IDE interface: Intel Corporation 82801JI (ICH10 Family) 4 port SATA IDE Controller 00:1f.3 SMBus: Intel Corporation 82801JI (ICH10 Family) SMBus Controller 00:1f.5 IDE interface: Intel Corporation 82801JI (ICH10 Family) 2 port SATA IDE Controller 02:00.0 FireWire (IEEE 1394): JMicron Technologies, Inc. Device 2380 03:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 02)

  Read the article

• Setting up Windows SBS 2008 network on Xen

  - by samyboy

  I'm trying to install a Windows SBS 2008 server in a Xen environment. The OS is booting fine. Unfortunately I can't figure out how to set up the network settings. Dom0 is a Debian Lenny hosting around 10 virtual servers. Here are the settings I'm using in the hosted Windows SBS: IP address: 10.20.0.8 Network mask: 255.255.0.0 Gateway: 10.20.0.1 Note that during the installation stage, Windows set the net mask at 255.255.255.0 without letting me choose. Gross. Windows SBS tells me I have a "limited connection". I can't ping the gateway nor any other IP except localhost and it's own IP (10.20.0.8). Here is the Xen config file: kernel = '/usr/lib/xen-3.2-1/boot/hvmloader' builder = 'hvm' memory = '4096' device_model='/usr/lib/xen-3.2-1/bin/qemu-dm' acpi=1 apic=1 pae=1 vcpus=1 name = 'winexchange' # Disks disk = [ 'phy:/dev/wnghosts/exchange-disk,ioemu:hda,w', 'file:/mnt/freespace/ISO/DVD1_Installation.iso,ioemu:hdc:cdrom,r' ] # Networking vif = [ 'mac=00:16:3E:0A:D0:1B, type=ioemu, bridge=xenbr0'] # video stdvga=0 serial='pty' ne2000=0 # Behaviour boot='c' sdl=0 # VNC vfb = [ 'type=vnc' ] vnc=1 vncdisplay=1 vncunused=1 usbdevice='tablet' This config is working with others Windows XP domU's. I tried to change the ne2000 values with 0 and 1 with no effect. I am far from having good Windows administration skills so I guess I definitely need some help on this case. Thanks.

  Read the article

• Blocking 'good' bots in nginx with multiple conditions for certain off-limits URL's where humans can go

  - by Glenn Plas

  After 2 days of searching/trying/failing I decided to post this here, I haven't found any example of someone doing the same nor what I tried seems to be working OK. I'm trying to send a 403 to bots not respecting the robots.txt file (even after downloading it several times). Specifically Googlebot. It will support the following robots.txt definition. User-agent: * Disallow: /*/*/page/ The intent is to allow Google to browse whatever they can find on the site but return a 403 for the following type of request. Googlebot seems to keep on nesting these links eternally adding paging block after block: my_domain.com:80 - 66.x.67.x - - [25/Apr/2012:11:13:54 +0200] "GET /2011/06/ page/3/?/page/2//page/3//page/2//page/3//page/2//page/2//page/4//page/4//pag e/1/&wpmp_switcher=desktop HTTP/1.1" 403 135 "-" "Mozilla/5.0 (compatible; G ooglebot/2.1; +http://www.google.com/bot.html)" It's a wordpress site btw. I don't want those pages to show up, even though after the robots.txt info got through, they stopped for a while only to begin crawling again later. It just never stops .... I do want real people to see this. As you can see, google get a 403 but when I try this myself in a browser I get a 404 back. I want browsers to pass. root@my_domain:# nginx -V nginx version: nginx/1.2.0 I tried different approaches, using a map and plain old nono if's and they both act the same: (under http section) map $http_user_agent $is_bot { default 0; ~crawl|Googlebot|Slurp|spider|bingbot|tracker|click|parser|spider 1; } (under the server section) location ~ /(\d+)/(\d+)/page/ { if ($is_bot) { return 403; # Please respect the robots.txt file ! } } I recently had to polish up my Apache skills for a client where I did about the same thing like this : # Block real Engines , not respecting robots.txt but allowing correct calls to pass # Google RewriteCond %{HTTP_USER_AGENT} ^Mozilla/5\.0\ \(compatible;\ Googlebot/2\.[01];\ \+http://www\.google\.com/bot\.html\)$ [NC,OR] # Bing RewriteCond %{HTTP_USER_AGENT} ^Mozilla/5\.0\ \(compatible;\ bingbot/2\.[01];\ \+http://www\.bing\.com/bingbot\.htm\)$ [NC,OR] # msnbot RewriteCond %{HTTP_USER_AGENT} ^msnbot-media/1\.[01]\ \(\+http://search\.msn\.com/msnbot\.htm\)$ [NC,OR] # Slurp RewriteCond %{HTTP_USER_AGENT} ^Mozilla/5\.0\ \(compatible;\ Yahoo!\ Slurp;\ http://help\.yahoo\.com/help/us/ysearch/slurp\)$ [NC] # block all page searches, the rest may pass RewriteCond %{REQUEST_URI} ^(/[0-9]{4}/[0-9]{2}/page/) [OR] # or with the wpmp_switcher=mobile parameter set RewriteCond %{QUERY_STRING} wpmp_switcher=mobile # ISSUE 403 / SERVE ERRORDOCUMENT RewriteRule .* - [F,L] # End if match This does a bit more than I asked nginx to do but it's about the same principle, I'm having a hard time figuring this out for nginx. So my question would be, why would nginx serve my browser a 404 ? Why isn't it passing, The regex isn't matching for my UA: "Mozilla/5.0 (X11; Linux x86_64) AppleWebKit/536.5 (KHTML, like Gecko) Chrome/19.0.1084.30 Safari/536.5" There are tons of example to block based on UA alone, and that's easy. It also looks like the matchin location is final, e.g. it's not 'falling' through for regular user, I'm pretty certain that this has some correlation with the 404 I get in the browser. As a cherry on top of things, I also want google to disregard the parameter wpmp_switcher=mobile , wpmp_switcher=desktop is fine but I just don't want the same content being crawled multiple times. Even though I ended up adding wpmp_switcher=mobile via the google webmaster tools pages (requiring me to sign up ....). that also stopped for a while but today they are back spidering the mobile sections. So in short, I need to find a way for nginx to enforce the robots.txt definitions. Can someone shell out a few minutes of their lives and push me in the right direction please ? I really appreciate ANY response that makes me think harder ;-)

  Read the article

• WRTU54G-TM router with 3rd party firmware; Can custom firmware include stock binary portions?

  - by dlamblin

  I've been doing a lot of reading online about the Linksys WRTU54G-TM router model that I now own. It seems getting a custom firmware onto it is not a problem. But no one is talking about retaining the Voip features (yet). So far they're all disappointed that it's not a SIP machine and used GSM over IPSec. Personally I don't care about using it with non-t-mobile. If I take the original firmware, shouldn't I be able to extract it, and it's SquashFS image, and then move all of the t-mobile specific binaries for enabling the calling features over to a custom firmware installation (maybe OpenWRT)? You might ask why, and the reason is, that if I do this I could retain my calling features, which I do want, and ssh to the router and use it to run additional software, as any OpenWRT router could do. Does anyone know if this can be done, and how the firmware's binaries could be gotten at and installed correctly? Update I have found someone working on 3rd party WRTU54G-TM firmware. I am still interested in my second part of the questions, that is can't the stock firmware images be pulled apart and have the close-source, if any, binary kernel modules moved into another more flexible custom firmware?

  Read the article

• Picking a linux compatible motherboard

  - by Chris

  Last time I bought a new computer (I build them myself) I got a motherboard that had really poor linux support for a long time. Specifically the audio. I had to wait months before the kernel supported the on board audio chipset. That is exactly the situation I'm trying to avoid this time around. I have some specific questions about "server motherboards" actually. I looked at a few models of server motherboards by intel, and some random models on newegg. I wasn't able to see much of a difference from regular desktop motherboard other than most had two sockets, and support for much more ram. These boards seem more popular with Linux users. Why? AMD and Intel both have server CPUs as well. Some question, what's the difference? To make this question more concrete, I was looking at this this motherboard. The main questions about it that I can't answer are: Can I get a motherboard without on board raid and audio? I wanted to get a hardware raid controller and a PCI audio card. I thought a server motherboard would be cheaper and not have these "extras", since who wants an audio card on a server? Where can I found out about Linux support for the components on this board? "Intel ICH10R", "Realtek ALC889", "Marvell 88E8056" I'm buying this computer to work as a Linux desktop for a lot of compiling, coding and audio/video work, but I don't want to rule out the possibility of installing windows and playing some games at one point. (even if the last game I got has been sitting in its box unopened for almost a year). Is it a good idea to buy a "server motherboard" and play games on it, or are desktop boards better value for this? The ultimate solution for me would be a motherboard that had GPL divers for onboard LAN, a single CPU socket, lots of PCI express and PCI. USB 3.0, and no fancy hard disk controllers since I'll be getting a separate one.

  Read the article

• USB Mouse and Keyboard not working in Linux 4 Tegra

  - by Sijo

  I am a new person in Tegra Linux development. I have Tamontem NG Evaluation board with Tegra 3 Chip. I installed L4T sample file system from NVIDIA tegra Resources (https://developer.nvidia.com/linux-tegra) and installed the file system as described in the documentation provided in NVIDIA site. Already these was an SD card with L4T running. i dont want to change the boot loader. So I copied the boot.scr.uimg to root (/) folder and uImage to boot(/boot/) and it starts booting from the existing SD card. After that while booting, some errors occurred in some Bluetooth devices (there is no bluetooth device in the board). So I disabled Bluetooth by giving the following command sudo mv /etc/init/bluetooth.conf /etc/init/bluetooth.conf.noexec Now the problem is that mouse and keyboard are not working. So i cannot login. Even though i installed desktop, the mouse and keyboard are not working. But mouse and keyboard are enumerating. lsusb command is showing the USB mouse and keyboard. The installed file system is Ubuntu 13.04. Linux Kernel version is 3.1 What to do. Please help.Thanks in Advance.

  Read the article

• Which linux distributions offer seamless support for UEFI and an LVM root out of the box?

  - by Jannik Jochem

  My new ultrabook (an Asus UX32VD) requires UEFI in order to boot from the internal harddisk. I use an LVM partition which contains my root fs and dual-boot Windows 8. I somehow managed to get this working on Sabayon Linux, however the overall process was pretty painful, and system upgrades keep breaking my configuration because everything depends on a hand-configured kernel and a hand-crafted GRUB2 configuration. This causes a lot of hassle and distractions for me, so I am considering to switch to a different distribution. However, I cannot find any concrete resources that precisely document the state of UEFI support in the popular distributions. As an example, the length of the Ubuntu wiki page on UEFI suggests that installing on UEFI systems is a non-trivial process, and this AskUbuntu thread on encrypted LVM on UEFI systems suggests that LVM might also be a problem. I know that this question seems somewhat open-ended, so I'll formulate concrete questions: Are there any Linux distributions with an installer that supports installing to an LVM root in a UEFI boot setting where Windows 8 is dual-booted? Which distributions support UEFI without having to jump through hoops in order to bootstrap into a UEFI-booted system or requiring manual configuration of the boot manager?

  Read the article

• How can I use two Internet connections in Ubuntu?

  - by Martin

  My goal is to be able to do something like this: curl google.com --interface ppp0 curl google.com --interface p2p2 ppp0 is a DSL connection, and p2p2 is a separate direct Internet connection. Currently I can only get one of these to work at a time. When I enable one, the other one stops working. /etc/network/interfaces: # The loopback network interface auto lo iface lo inet loopback # DSL auto p2p1 iface p2p1 inet manual auto dsl-provider iface dsl-provider inet ppp pre-up /sbin/ifconfig p2p1 up # line maintained by pppoeconf provider dsl-provider # DIRECT auto p2p2 iface p2p2 inet dhcp ifconfig: lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:65536 Metric:1 p2p1 Link encap:Ethernet inet6 addr: fe80::20a:ebff:fe21:99c6/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 p2p2 Link encap:Ethernet inet addr:192.168.1.101 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::20a:ebff:fe17:1249/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 ppp0 Link encap:Point-to-Point Protocol inet addr:53.193.231.167 P-t-P:53.193.224.1 Mask:255.255.255.255 UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1492 Metric:1 route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 0.0.0.0 0.0.0.0 0.0.0.0 U 0 0 0 ppp0 10.0.10.0 0.0.0.0 255.255.255.0 U 0 0 0 eth2 53.193.224.1 0.0.0.0 255.255.255.255 UH 0 0 0 ppp0 192.168.1.0 0.0.0.0 255.255.255.0 U 0 0 0 p2p2 By default, only ppp0 works. If I run "route add default gw 192.168.1.1 p2p2" then I can use p2p2 but ppp0 stops working. If I then run "route add default gw 53.193.224.1 ppp0" then I can use ppp0 again but p2p2 stops working. What can I do to be able to use both interfaces selectively?

  Read the article

• What could cause a huge packet loss in Ubuntu 9.10, for both wired and wireless?

  - by xzenox

  I was previously using 9.04 fine (and in fact, I am posting this from my old 9.04 live cd). I tested the following install steps in a virtualbox vm prior to following the sames ones to upgrade my laptop: Download/burn ubuntu minimal cd (12mb one) Install ubuntu minimal sudo apt-get update sudo apt-get upgrade sudo apt-get ubuntu-desktop ubuntu-standard In the VM worked fine and I found myself with a working 9.10 ubuntu, network worked fine and I was able to test my backups and DropBox without a hitch (host was 9.04). When I followed the same steps on my laptop, everything worked up to after 9.10 being installed and working. As far as I can tell, everything besides eth0/wireless works. For some reason, I am unable to access the internet. Ping reports that over 99% of packets get lost (over an hour or so of pinging). This means for example that if I try hard enough, I can load a webpage but only at the cost of much patience... This happens both for a wired and wireless connection to my wrt310n (updated with latest firmware). At first I thought that it could be related to the ipv6 issues ppl have been experiencing however even after disabling ipv6 at the kernel level (through grub), I still get the issue. I do not think this is related to DNS issues or the likes since even when I ping my ISP's gateway IP, I have the same amount of packet loss. No DNS resolving should be required there. Access to my router works peachy with no packet loss there. I've tried different MTU values but to no avail. Note that this issue affects every web-enabled application: firefox, ping, synaptic, etc. The same hardware/router combo works with 9.04 but not with 9.10. In fact, when I did: sudo apt-get ubuntu-desktop ubuntu-standard after 9.10 minimal was installed, it downloaded over 400mb of packages without a hitch so my guess is that one of those packages either in ubuntu-desktop or ubuntu-standard is causing havok. Thoughts?

  Read the article

• Unicenter Software Delivery 4 not able to connect to MS SQL 2000 Database after W2003 SP2 upgrade

  - by grub

  Hello Everyone Yesterday I installed the Windows Server 2003 Service Pack 2 on a Windows Server 2003 which has Unicenter Software Delivery 4 installed. Prior to the installation I disabled every CA service on the server (Brightstor, SDO , RCO, TNG) and the MS SQL 2000 service. After the installation of the SP2 I enabled the services again but the Unicenter Service is not able to connect to the MS SQL 2000 Database anymore. The database itself is up and running and I can connect to it with the Enterprise Manager. A dbcc checkdb doesnt return any errors on the Unicenter database. The Unicenter service throws the following error messages during startup: IM[1] 27/05 10:38:31,272 Installation Manager in init phase IM[1] 27/05 10:38:31,694 Process IM(L) - [004152] failed to open database SDDATA. dbopen() call failed. IM[1] 27/05 10:38:31,694 sqls error details: IM[1] 27/05 10:38:31,694 (null) IM[1] 27/05 10:38:32,069 ##EXCEPTION## TableError T@:PS_SQLS\isam_db.cxx:744. IM[1] 27/05 10:38:32,069 ##EXCEPTION## TableError C@:TaskmgrL\ASMTML.CXX:596. IM[1] 27/05 10:38:32,069 ##EXCEPTION## ErrorCode: 4711 in SDDATA:Isam::Isam. Process IM(L) - [004152] failed to open database SDDATA. dbopen() call failed. IM[1] 27/05 10:38:32,069 sqls error details: IM[1] 27/05 10:38:32,069 (null) IM[1] 27/05 10:38:32,069 returned 0. IM[1] 27/05 10:38:32,084 Persistent Storage could not be opened. Error cause is found in the ASM Event Log. Restart Task Manager. IM[1] 27/05 10:38:32,084 Failed to open database. IM[1] 27/05 10:38:32,084 Installation Manager ends> If I check the Unicenter configutation with *chkmib_l* the tool throws an exception and creates a small dump file. An Exception Occurred: Time: 27/05 09:49:38,928 Reason: ChkMIB_l.exe caused an UNKNOWN_EXCEPTION in module kernel32.dll at 7C82001B:77E4BEE7 Registers: EAX=0012F908 EBX=00000000 ECX=00000000 EDX=02410004 ESI=0012F998 EDI=0012F998 EBP=0012F958 ESP=0012F904 EIP=77E4BEE7 FLG=00000206 CS =7C82001B DS =B90023 SS =120023 ES =120023 FS =7C82003B GS =3F0000 Call Stack: 7C82001B:77E4BEE7 (0xE06D7363 0x00000001 0x00000003 0x0012F98C) kernel32.dll 7C82001B:77BB3259 (0x0012F9B8 0x2B017C50 0x2B024404 0x00B68C98) MSVCRT.dll 7C82001B:2B010C42 (0x00020003 0x010C00FE 0x003F0190 0x00B69050) PS.dll << SOFTWARE DELIVERY INSTANCE INFO >> TRIGGER 0(1) instances: JCE 0(1) instances: TM 0(1) instances: IM 0(1) instances: DM 0(1) instances: DPU 0(71) instances: NATF 0(1) instances: MIBCONV 0(0) instances: API 0(4) instances: DTSFT 0(0) instances: TNGPOP 0(0) instances: DGATE 0(0) instances: << FLUSHING MEMORY TRACES >> << STOP FLUSHING MEMORY TRACES >> I compared the configuration of the SDO service and the system configuration with another server on which the Windows Server 2003 SP2 is installed and SDO is working. The configuration is the same and the same driver and software versions are used. Do you have any idea what causes the connection issue? Should I deinstall the unicenter service and make a fresh installation on the server or should I remove the Windows Server 2003 SP2? I don't want to remove the SP2 because it's a requirement for WSUS3 SP2 and I really don't want to know how many possible exploits are possible in such an old system ;-) Thank you very much and have a nice day. Below you can find more detailed information about the system and the SDO service. psinfo output (system information) System information for \\CZZAAS1003: Uptime: 0 days 14 hours 38 minutes 50 seconds Kernel version: Microsoft Windows Server 2003, Multiprocessor Free Product type: Standard Edition Product version: 5.2 Service pack: 2 Kernel build number: 3790 Install date: 23.9.2004, 11:16:11s IE version: 6.0000 System root: C:\WINDOWS Processors: 2 Processor speed: 2.3 GHz Processor type: Intel(R) Xeon(TM) CPU Physical memory: 1024 MB Video driver: RAGE XL PCI Family (Microsoft Corporation) sdver output (Unicenter Software delivery version) Unicenter Software Delivery 4.0 SP1 I2 ENU [2901] Copyright 2004 Computer Associates International, Incorporated ms sql 2000 version and odbc driver version MS SQL 2000 Server Standard Edition Product Version: 8.00.760 (SP3) ODBC Driver: SQL Server - Version 2000.86.3959.00 complete Unicenter Software delivery service log file TRIGGER[1] 27/05 10:38:28,366 SD Trigger Agent has started NATF[1] 27/05 10:38:28,928 Initiation phase finished IM[1] 27/05 10:38:31,272 Installation Manager in init phase IM[1] 27/05 10:38:31,694 Process IM(L) - [004152] failed to open database SDDATA. dbopen() call failed. IM[1] 27/05 10:38:31,694 sqls error details: IM[1] 27/05 10:38:31,694 (null) IM[1] 27/05 10:38:32,069 ##EXCEPTION## TableError T@:PS_SQLS\isam_db.cxx:744. IM[1] 27/05 10:38:32,069 ##EXCEPTION## TableError C@:TaskmgrL\ASMTML.CXX:596. IM[1] 27/05 10:38:32,069 ##EXCEPTION## ErrorCode: 4711 in SDDATA:Isam::Isam. Process IM(L) - [004152] failed to open database SDDATA. dbopen() call failed. IM[1] 27/05 10:38:32,069 sqls error details: IM[1] 27/05 10:38:32,069 (null) IM[1] 27/05 10:38:32,069 returned 0. IM[1] 27/05 10:38:32,084 Persistent Storage could not be opened. Error cause is found in the ASM Event Log. Restart Task Manager. IM[1] 27/05 10:38:32,084 Failed to open database. IM[1] 27/05 10:38:32,084 Installation Manager ends TM[1] 27/05 10:38:32,116 Task Manager in init phase TM[1] 27/05 10:38:32,334 Process TM(L) - [006132] failed to open database SDDATA. dbopen() call failed. TM[1] 27/05 10:38:32,334 sqls error details: TM[1] 27/05 10:38:32,334 (null) TM[1] 27/05 10:38:32,381 ##EXCEPTION## TableError T@:PS_SQLS\isam_db.cxx:744. TM[1] 27/05 10:38:32,381 ##EXCEPTION## TableError C@:TaskmgrL\ASMTML.CXX:596. TM[1] 27/05 10:38:32,381 ##EXCEPTION## ErrorCode: 4711 in SDDATA:Isam::Isam. Process TM(L) - [006132] failed to open database SDDATA. dbopen() call failed. TM[1] 27/05 10:38:32,381 sqls error details: TM[1] 27/05 10:38:32,381 (null) TM[1] 27/05 10:38:32,381 returned 0. TM[1] 27/05 10:38:32,381 Persistent Storage could not be opened. Error cause is found in the ASM Event Log. Restart Task Manager. TM[1] 27/05 10:38:32,381 Failed to open database. TM[1] 27/05 10:38:32,381 Task Manager ends DM[1] 27/05 10:38:33,272 Dialogue Manager is now active API[1] 27/05 10:38:34,397 API Server Process in init phase API[1] 27/05 10:38:34,397 API - SDNLS_Init API[1] 27/05 10:38:34,397 API - connectEM API[1] 27/05 10:38:34,412 API - apiServ.init DM[1] 27/05 10:38:34,678 **AND** 1 Agents triggered API[1] 27/05 10:38:34,709 Process API(L) - [005680] failed to open database SDDATA. dbopen() call failed. API[1] 27/05 10:38:34,709 sqls error details: API[1] 27/05 10:38:34,709 (null) API[1] 27/05 10:38:34,756 ##EXCEPTION## TableError T@:PS_SQLS\isam_db.cxx:744. API[1] 27/05 10:38:34,756 ##EXCEPTION## TableError C@:MainAPIL\APISERVL.CXX:246. API[1] 27/05 10:38:34,756 ##EXCEPTION## ErrorCode: 4711 in SDDATA:Isam::Isam. Process API(L) - [005680] failed to open database SDDATA. dbopen() call failed. API[1] 27/05 10:38:34,756 sqls error details: API[1] 27/05 10:38:34,756 (null) API[1] 27/05 10:38:34,756 returned 0. API[1] 27/05 10:38:34,756 Open of the database failed. API[1] 27/05 10:38:34,756 API - apiServ.init complete API[1] 27/05 10:38:34,756 API - start_APIServer DM[1] 27/05 10:38:34,803 CZZAAR1037 DPU[1:CZZAAR1037] 27/05 10:38:35,772 DPU in init phase DPU[1:CZZAAR1037] 27/05 10:38:36,100 >> GetManagerData DPU[1:CZZAAR1037] 27/05 10:38:36,287 >> SetCompInfo DPU[1:CZZAAR1037] 27/05 10:38:36,334 >> GetContainerList DPU[1:CZZAAR1037] 27/05 10:38:36,350 getJobState 3 from 5b6ad DPU[1:CZZAAR1037] 27/05 10:38:36,350 getJobState 3 from 5b6ad DPU[1:CZZAAR1037] 27/05 10:38:36,350 getJobState 3 from 5b6b7 DPU[1:CZZAAR1037] 27/05 10:38:36,350 getJobState 3 from 5b6b7 DPU[1:CZZAAR1037] 27/05 10:38:36,350 getJobState 3 from 5b6c1 DPU[1:CZZAAR1037] 27/05 10:38:36,350 getJobState 3 from 5b6c1 DPU[1:CZZAAR1037] 27/05 10:38:36,366 getJobState 3 from 5b6cb DPU[1:CZZAAR1037] 27/05 10:38:36,366 getJobState 3 from 5b6cb DPU[1:CZZAAR1037] 27/05 10:38:36,366 getJobState 3 from 5b6f9 DPU[1:CZZAAR1037] 27/05 10:38:36,366 getJobState 3 from 5b6f9 DPU[1:CZZAAR1037] 27/05 10:38:36,366 getJobState 3 from 5b71a DPU[1:CZZAAR1037] 27/05 10:38:36,366 getJobState 3 from 5b71a DPU[1:CZZAAR1037] 27/05 10:38:36,366 getJobState 3 from 5b724 DPU[1:CZZAAR1037] 27/05 10:38:36,381 getJobState 3 from 5b724 DPU[1:CZZAAR1037] 27/05 10:38:36,397 getJobState 3 from 5b72e DPU[1:CZZAAR1037] 27/05 10:38:36,397 getJobState 3 from 5b72e DPU[1:CZZAAR1037] 27/05 10:38:36,397 getJobState 3 from 5b738 DPU[1:CZZAAR1037] 27/05 10:38:36,397 getJobState 3 from 5b738 DPU[1:CZZAAR1037] 27/05 10:38:36,397 getJobState 3 from 5b742 DPU[1:CZZAAR1037] 27/05 10:38:36,397 getJobState 3 from 5b742 DPU[1:CZZAAR1037] 27/05 10:38:36,397 getJobState 3 from 5b74c DPU[1:CZZAAR1037] 27/05 10:38:36,397 getJobState 3 from 5b74c DPU[1:CZZAAR1037] 27/05 10:38:36,397 getJobState 3 from 5b756 DPU[1:CZZAAR1037] 27/05 10:38:36,397 getJobState 3 from 5b756 DPU[1:CZZAAR1037] 27/05 10:38:36,397 getJobState 3 from 5b78a DPU[1:CZZAAR1037] 27/05 10:38:36,397 getJobState 3 from 5b78a DPU[1:CZZAAR1037] 27/05 10:38:36,397 getJobState 3 from 5b7af DPU[1:CZZAAR1037] 27/05 10:38:36,397 getJobState 3 from 5b7af DPU[1:CZZAAR1037] 27/05 10:38:36,522 >> SetCompAttr DPU[1:CZZAAR1037] 27/05 10:38:36,569 >> SetDetected DPU[1:CZZAAR1037] 27/05 10:38:36,584 disconnect DPU[1:CZZAAR1037] 27/05 10:38:36,584 getJobState 3 from 5b6ad DPU[1:CZZAAR1037] 27/05 10:38:36,584 getJobState 3 from 5b6b7 DPU[1:CZZAAR1037] 27/05 10:38:36,584 getJobState 3 from 5b6c1 DPU[1:CZZAAR1037] 27/05 10:38:36,584 getJobState 3 from 5b6cb DPU[1:CZZAAR1037] 27/05 10:38:36,584 getJobState 3 from 5b6f9 DPU[1:CZZAAR1037] 27/05 10:38:36,584 getJobState 3 from 5b71a DPU[1:CZZAAR1037] 27/05 10:38:36,584 getJobState 3 from 5b724 DPU[1:CZZAAR1037] 27/05 10:38:36,584 getJobState 3 from 5b72e DPU[1:CZZAAR1037] 27/05 10:38:36,584 getJobState 3 from 5b738 DPU[1:CZZAAR1037] 27/05 10:38:36,584 getJobState 3 from 5b742 DPU[1:CZZAAR1037] 27/05 10:38:36,584 getJobState 3 from 5b74c DPU[1:CZZAAR1037] 27/05 10:38:36,584 getJobState 3 from 5b756 DPU[1:CZZAAR1037] 27/05 10:38:36,584 getJobState 3 from 5b78a DPU[1:CZZAAR1037] 27/05 10:38:36,584 getJobState 3 from 5b7af DPU[1:CZZAAR1037] 27/05 10:38:36,584 DPU ends DM[1] 27/05 10:38:38,006 **AND** 0 Agents triggered JCE[1] 27/05 10:38:38,053 JCE starts DM[1] 27/05 10:38:38,287 CZZAAS1003 DPU[2:CZZAAS1003] 27/05 10:38:38,412 DPU in init phase DPU[2:CZZAAS1003] 27/05 10:38:38,647 >> GetManagerData DPU[2:CZZAAS1003] 27/05 10:38:38,756 >> SetCompInfo DPU[2:CZZAAS1003] 27/05 10:38:38,787 >> GetContainerList DM[1] 27/05 10:38:38,850 **AND** 1 Agents triggered DM[1] 27/05 10:38:38,928 CZZAAR1124 DPU[3:CZZAAR1124] 27/05 10:38:39,053 DPU in init phase DPU[3:CZZAAR1124] 27/05 10:38:39,272 >> GetManagerData DM[1] 27/05 10:38:39,334 **AND** 1 Agents triggered DPU[3:CZZAAR1124] 27/05 10:38:39,381 >> SetCompInfo DPU[3:CZZAAR1124] 27/05 10:38:39,412 >> GetContainerList DM[1] 27/05 10:38:39,412 CZZAAR1125 DPU[3:CZZAAR1124] 27/05 10:38:39,428 getJobState 3 from 5b88e DPU[3:CZZAAR1124] 27/05 10:38:39,428 getJobState 3 from 5b88e DPU[2:CZZAAS1003] 27/05 10:38:39,491 >> SetCompAttr DPU[3:CZZAAR1124] 27/05 10:38:39,522 >> SetCompAttr DPU[4:CZZAAR1125] 27/05 10:38:39,522 DPU in init phase DPU[3:CZZAAR1124] 27/05 10:38:39,584 >> SetDetected DPU[2:CZZAAS1003] 27/05 10:38:39,584 >> SetDetected DPU[3:CZZAAR1124] 27/05 10:38:39,584 disconnect DPU[3:CZZAAR1124] 27/05 10:38:39,600 getJobState 3 from 5b88e DPU[3:CZZAAR1124] 27/05 10:38:39,600 DPU ends DPU[2:CZZAAS1003] 27/05 10:38:39,631 disconnect DPU[2:CZZAAS1003] 27/05 10:38:39,631 DPU ends DPU[4:CZZAAR1125] 27/05 10:38:39,756 >> GetManagerData DPU[4:CZZAAR1125] 27/05 10:38:39,850 >> SetCompInfo DPU[4:CZZAAR1125] 27/05 10:38:39,881 >> GetContainerList DPU[4:CZZAAR1125] 27/05 10:38:39,897 getJobState 3 from 5b8a9 DPU[4:CZZAAR1125] 27/05 10:38:39,897 getJobState 3 from 5b8a9 DPU[4:CZZAAR1125] 27/05 10:38:39,991 >> SetCompAttr DPU[4:CZZAAR1125] 27/05 10:38:40,100 >> SetDetected DPU[4:CZZAAR1125] 27/05 10:38:40,116 disconnect DPU[4:CZZAAR1125] 27/05 10:38:40,116 getJobState 3 from 5b8a9 DPU[4:CZZAAR1125] 27/05 10:38:40,116 DPU ends DM[1] 27/05 10:38:40,741 **AND** 0 Agents triggered JCE[1] 27/05 10:38:42,756 JCE ends DM[1] 27/05 10:38:47,475 **AND** 0 Agents triggered DM[1] 27/05 10:38:54,241 **AND** 0 Agents triggered

  Read the article

• Debian/OVH: How to configure multiple Failover IP on the same Xen (Debian) Virtual Machine?

  - by D.S.

  I have a problem on a Xen virtual machine (running latest Debian), when I try to configure a second failover IP address. OVH reports that my IP is misconfigured and they complaint they receive a massive quantity of ARP packets from this IPs, so they are going to block my IP unless I fix this issue. I suspect there's a routing issue, but I don't know (and can't find any useful info on the provider's website, and their support doesn't provide me a valid solution, just bounce me to their online - useless - guides). My /etc/network/interfaces look like this: # The loopback network interface auto lo iface lo inet loopback # The primary network interface auto eth0 iface eth0 inet static address AAA.AAA.AAA.AAA netmask 255.255.255.255 broadcast AAA.AAA.AAA.AAA post-up route add 000.000.000.254 dev eth0 post-up route add default default gw 000.000.000.254 dev eth0 # Secondary NIC auto eth0:0 iface eth0:0 inet static address BBB.BBB.BBB.BBB netmask 255.255.255.255 broadcast BBB.BBB.BBB.BBB And the routing table is: Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 000.000.000.254 0.0.0.0 255.255.255.255 UH 0 0 0 eth0 0.0.0.0 000.000.000.254 0.0.0.0 UG 0 0 0 eth0 In these examples (true IP addresses are replaced by fake ones, guess why :)), 000.000.000.000 is my main server's IP address (dom0), 000.000.000.254 is the default gateway OVH recommends, AAA.AAA.AAA.AAA is the first IP Failover and BBB.BBB.BBB.BBB is the second one. I need both AAA.AAA.AAA.AAA and BBB.BBB.BBB.BBB to be publicly reachable from Internet and point to my domU, and to be able to access Internet from inside the virtual machine (domU). I am using eth0 and eth0:0 because due to OVH support, I have to assign both IPs to the same MAC address and then create a virtual eth0:0 interface for the second IP. Any suggestion? What am I doing wrong? How can I stop OVH complaining about ARP flood? Many thanks in advance, DS

  Read the article

• Synergy, OSX client, Windows 7 server - No mouse on client

  - by Majenko

  I have the following Synergy setup: +------------++------------++------------++------------+ | Mac || Win 7 || Ubuntu 1 || Ubuntu 2 | |c ||s ||c ||c | +------------++------------++------------++------------+ Mac: OS/X Tiger 10.4.11 (G3) Win 7: Windows 7 Ultimate x64 Ubuntu 1 & Ubuntu 2: Desktop 10.10 Now, everything works nicely between the Win7 server and the two Ubuntu machines. What doesn't work is the Mac. I am running the very latest Synergy (1.4.2, downloaded last night). As far as the Mac is concerned everything should be working fine: Synergy 1.4.2 Client on Darwin 8.11.0 Darwin Kernel Version 8.11.0: Wed Oct 10 18:26:00 PDT 2007; root:xnu-792.24.17~1/RELEASE_PPC Power Macintosh Unable to connect to pasteboard. Clipboard sharing disabled. 2011-03-22 09:32:56.725 synergyc[406] Can't register screen saver connection 'com.apple.ScreenSaverDaemon' started client connecting to '192.168.0.202': 192.168.0.202:24800 connected to server entering screen leaving screen entering screen leaving screen But it's just not interacting with the display at all (mouse doesn't move, keyboard does nothing). I have tried running ktrace on synergyc and examining the dump, and the only clue I found was that it was trying to interact with the AccessibilityAPI which was disabled at first. Enabling Accessibility has had no effect whatsoever (it has only stopped the failure to open /var/db/.AccessibilityAPIEnabled in the ktrace dump) Anyone managed to get this to work in OS/X Tiger yet? I used to run the server on OS/X and have the windows / unix machines as clients, but as my Windows is now a laptop I'd like that to be the server.

  Read the article

• ipv6 : why ndp resolves to global scope address?

  - by Julien

  I'm facing a strange ipv6 behavior and I don't know how to solve it because I'm not familiar with ipv6. Maybe this behavior is normal. I hope that you will help me. ( I'm running under debian 6.0.9 with a custom kernel 3.2.58 ) machine A is "2a00:7d30:edf6:100::1" wants to ping machine B, which is "2a00:7d30:edf6:100::10". Both are on the same segment. machine A asks for the address of machine B and I don't understand why machine B gives its global scope address instead of the local scope one ? 10:59:02.082785 IP6 2a00:7d30:edf6:100::1 ff02::1:ff00:10: ICMP6, neighbor solicitation, who has 2a00:7d30:edf6:100::10, length 32 10:59:02.082821 IP6 2a00:7d30:edf6:100::10 2a00:7d30:edf6:100::1: ICMP6, neighbor advertisement, tgt is 2a00:7d30:edf6:100::10, length 32 after that machine A pings the global scope address of machine B and it works fine : 10:59:02.082927 IP6 2a00:7d30:edf6:100::1 2a00:7d30:edf6:100::10: ICMP6, echo request, seq 1, length 64 10:59:02.082960 IP6 2a00:7d30:edf6:100::10 2a00:7d30:edf6:100::1: ICMP6, echo reply, seq 1, length 64 Thank you for you help best regards Julien

  Read the article

• Issue booting Linux Mint from Live CD?

  - by Vee

  I had Windows 8 and Linux Mint 15 dual booted on my laptop. When I first installed Linux, I wasn't able to load into because the grub would not show. To fix this, I used boot-repair from a Live CD. This time, I updated to Windows 8.1 and it showed a watermark telling me my secure boot wasn't configured properly. I then went and enabled secure boot (BIOS) and I believe it was after that that the Grub would not show once again. I tried to boot from a Linux CD again but when I try, it gives me the following errors: error: failure reading sector 0x0 from 'hd1' error: you need to load the kernel first. Press any key to continue... Before, it was giving me an error with sector 0x6d200 or something instead of 0x0. I am completely unsure of what to do. I do not know what other details to give except that this my have happened after I enabled secure boot, and I actually clicked reset to default setting so I am unsure if any other settings were changed in the BIOS menu.

  Read the article

• Interpreting and using the Asterisk "timing test" command

  - by zigg

  Timing is very important for certain kinds of applications in Asterisk. If DAHDI is the timing source, the dahdi_test command can be used to check the timing provided by the DAHDI kernel module. If dahdi_test returns exclusively measurements above 99.975%, the DAHDI timing source is generally considered good. Since Asterisk 1.6, new timing sources have become available, such as pthread and timerfd. The accuracy of these timing sources seems to be measurable with the Asterisk CLI timing test command: localhost*CLI> timing test Attempting to test a timer with 50 ticks per second. Using the 'timerfd' timing module for this test. It has been 1000 milliseconds, and we got 50 timer ticks My concern is that timing 50 ticks seems to be a considerably less stressful test than dahdi_test's 8192 samples in 8000 ms, particularly since just about every system I've tried it on, virtual or otherwise, can handle it. I can ask timing test to ramp it up to what I think are dahdi_test's standards: localhost*CLI> timing test 1024 Attempting to test a timer with 1024 ticks per second. Using the 'timerfd' timing module for this test. It has been 1000 milliseconds, and we got 1024 timer ticks This will indeed break down a bit depending on the system I'm using, usually with a decrease in timer ticks. But I'm not sure whether this is useful to stress it to this level. Is there authoritative guidance on using and interpreting the timing test command to insure that a given Asterisk system has a timing source that will work well?

  Read the article

• Accidentally mounted a ReiserFS drive as MBR on my windows box - how do I recover?

  - by Ryan

  I had a WD Netcenter with a 160GB drive that kept dropping off the network. I opened up the enclosure and removed the hard drive, connected to a Windows box without knowing the drive used ReiserFS.... When mounting on the Windows box, I chose "MBR" as filesystem. 70GB of data corrupted: 90% of data is word documents, excel spreadsheets, and jpg's - all mission critical. Attempted recovery on Linux box (ubuntu) using TestDisk: I could see the container, but couldn't get anything out – according to TestDisk this was because I chose "none" as filesystem. Attempted recovery using Nucleus Kernel Recovery for windows: 98% of what was recovered is incomplete and/or unusable. I need to know if a way exists to recover or rebuild original ReiserFS MBR, or what tools/techniques might give me the best results in recovering the data. Found a Windows version of TestDisk and I ran it yesterday - here are the results: TestDisk 6.14-WIP, Data Recovery Utility, May 2012 Christophe GRENIER <[email protected]> http://www.cgsecurity.org Disk /dev/sda - 160 GB / 149 GiB - CHS 19457 255 63 The harddisk (160 GB / 149 GiB) seems too small! (< 519 GB / 483 GiB) Check the harddisk size: HD jumpers settings, BIOS detection... The following partitions can't be recovered: Partition Start End Size in sectors > ReiserFS 3.6 62 241 8 19458 0 18 311581568 ReiserFS 3.6 62 248 55 19458 8 2 311581568 ReiserFS 3.6 62 254 37 19458 13 47 311581568 ReiserFS 3.6 63 6 28 19458 20 38 311581568 ReiserFS 3.6 63 13 11 19458 27 21 311581568 ReiserFS 3.6 63 21 43 19458 35 53 311581568 ReiserFS 3.6 63 27 41 19458 41 51 311581568 ReiserFS 3.6 63 37 35 19458 51 45 311581568 ReiserFS 3.6 63 54 20 19458 68 30 311581568 ReiserFS 3.6 63 76 26 19458 90 36 311581568

  Read the article

• Updating modules on VPS hosted under OpenVZ

  - by tertle

  Been trying to install OpenVPN on a VPS but come into a few problems when trying to start the openvpn server: Service deferred error: IPTablesServiceBase: failed to run iptables-restore [status=1]: ['FATAL: Could not load /lib/modules/2.6.18-028stab070.14/modules.dep: No such file or directory', 'FATAL: Could not load /lib/modules/2.6.18-028stab070.14/modules.dep: No such file or directory', 'iptables-restore: line 46 failed']: internet/base:1175,internet/base:752,internet/process:45,internet/process:306,internet/_baseprocess:48,internet/process:775,internet/_baseprocess:60,svc/pp:116,svc/svcnotify:26,internet/defer:238,internet/defer:307,internet/defer:323,sagent/ipts:105,sagent/ipts:39,util/error:52,util/error:32 service failed to start due to unresolved dependencies: set(['user', 'iptables_openvpn']) service failed to start due to unresolved dependencies: set(['user', 'iptables_openvpn']) service failed to start due to unresolved dependencies: set(['iptables_openvpn']) Anyway so after a bit of playing around and some advice, I found that the Linux kernel and modules don't match on my server. uname -r returns 2.6.18-028stab070.14 and ls /lib/modules returns 2.6.18-028stab070.7 The server is running OpenVZ and my container uses Ubuntu 9.10. So my question is, is it possible for me to update my modules on a VPS and if so how would I do this, or is this something I'll need to try get my host to do? Thanks in advance.

  Read the article

• Windows 7 network performance tuning for LAN

  - by Hubert Kario

  I want to tune Windows 7 TCP stack for speed in a LAN environment. Bit of background info: I've got a Citrix XenServer set up with Windows 2008R2, Windows 7 and Debian Lenny with Citrix kernel, Windows machines have Tools installed the iperf server process is running on different host, also Debian Lenny. The servers are otherwise idle, tests were repeated few times to confirm results. While testing with iperf 2008R2 can achieve around 600-700Mbps with no tuning what so ever but I can't find any guide or set of parameters that will make Windows 7 achieve anything over 150Mbps with no change in TCP window size using -w parameter to iperf. I tried using netsh autotuining to disabled, experimental, normal and highlyrestricted - no change. Changing congestionprovider doesn't do anything, just as rss and chimney. Setting all the available settings to same values as on Windows 2008R2 host doesn't help. To summarize: Windows 2008R2 default settings: 600-700Mbps Debian, default settings: 600Mbps Windows 7 default settings: 120Mbps Windows 7 default, iperf -w 65536: 400-500Mbps While the missing 400Mbps in performance I blame on crappy Realtek NIC in the XenServer host (I can do ~980Mbps from my laptop to the iperf server) it doesn't explain why Windows 7 can't achieve good performance without manually tuning window size at the application level. So, how to tune Windows 7?

  Read the article

• Files on ext4 on Drobo with corrupt, zero-ed out blocks

  - by Patrick

  I have a 2TB ext4 file system (Ubuntu running Linux kernel 2.6.31-22-server x86_64). This file system is the second drive on a Drobo box plugged in via USB. We've not had problems on the first drive (Drobo limits drive size to 2TB due to some OS limitations, so if you have more space than that it appears as two separate drives). I am sharing this files with Samba (smbd 3.4.0) with a mix of Windows and Linux workstations. Recently we've been experiencing some data corruption in multiple files. In many cases I have an un-corrupt original file stored on one of the workstations. These are binary files of various formats, (e.g. SQLite, but others as well). I used "split" to split a corrupt and uncorrupt file into 4096 byte chunks (this is the block size of the ext4 file system). I then ran md5sum on pairs of chunks and discovered that the chunks matched in many cases and in every case where they did not match, the corrupt chunk was a solid chunk of zeroes (620f0b67a91f7f74151bc5be745b7110 for what it's worth). I'm trying to track down a culprit but am a bit at a loss. I don't believe Samba is at fault since I'm using it without issue on the first drive exported by the Drobo. What can I do to narrow this down and find out what's going on?

  Read the article

< Previous Page | 167 168 169 170 171 172 173 174 175 176 177 178  | Next Page >