Search Results

Search found 4572 results on 183 pages for 'dual monitors'.

Page 173/183 | < Previous Page | 169 170 171 172 173 174 175 176 177 178 179 180  | Next Page >

• Intermittent internet access on a flat network - Router is connected

  - by Naveed

  I’m looking for some help with network settings. I’ve just started a new job (non-IT!) and we have problems with our office network. I’m the most IT literate in the organisation (15 permanent employees) and so have been dealing with IT issues. Our main bit of software is web-based so we need constant web access but it sometimes goes down for between 20 minutes and 3 hours despite everything seemingly working fine. It’s a flat network with wireless APs, BT Business Broadband 8Mbit connection and that’s about it. We have no servers and no standard settings and staff are encouraged to bring in their own laptops and connect! The network basically exists to provide internet access and that’s it. We also have students accessing the wireless (and I know there’s a whole list of access and content issues etc but right now we just need internet access stabilised). This is what we have: Building 1 Cisco SLM-224P 24-port PoE 10/100 switch with 2 gigabit ports 3 x ZyXEL NWA-3160 wireless APs Samsung OfficeServ 7100 phone server which borrows the building’s wiring Building 2 Netgear GS605-UK 5-port 10/100/1000 switch 1 x ZyXEL NWA-3160 wireless AP 1 x BT Business Hub – 2wire BT2700hgv – is the DHCP server We have 2 link cables between the buildings. One connects the two switches on a gigabit port. The second (oddly) connects the switch in building 2 to the OfficeServ server in building 1. When the internet goes down I can still access the router through a wireless connection. I can also ping websites and get a response. Firefox just says “Cannot connect” etc. The system then heals itself when it feels like it. (Sorry if this is asking too much but) These are my immediate questions… Why would browser-based internet go down? I don’t know enough about protocols etc but I can try to standardise settings. The WAPs have a DNS server setting and I don’t know whether it should be “None” or “From DHCP”. What should be the DHCP server? The router or the Cisco switch? Or something else?! Would there be any problem in connecting the second link from switch to switch? Is that good practice? Is it worth swapping the Netgear GS605 with either a Cisco SG200-08 or Netgear GS108T-200? Is it worth upgrading the router to, for instance, a Cisco RV042G Dual Gigabit router which would also act as a switch? Or is it better to have a separate router and switch in Building 2?

  Read the article

• Why do I have multiple drives in my backup system image?

  - by bebop

  I have a drive which has 2 partitions. One is where the OS is installed, the other is a data (but not libraries) drive. When I try and create a backup using the built in tool, it wants to include both partitions in the system image. Why does it do this? If I move the os to a separate drive will I be able to back up just this data? Edit: To be more clear. I have 4 disks in the machine. 1 disc has 2 partitions. These are c: and e:, the other disks are d: f: and h:. The OS is installed on c: and libraries are stored on h:. The libraries are already backed up using crashplan, but I want to create a system image so I can easily restore the machine, if it either dies or if I get a SSD drive. When I choose backup (either through the wizard or if I open it through control panel) and check (or click) create a system image it automatically adds both c: and e: to the list of drives that will be backed up, and I cannot change this, the checkboxes to unselect are greyed out. I would like to know why it automatically adds e: to the list (but not h:, where the libraries are) and if I can change some setting so whatever files it has on e: that it thinks need to be backed up as part of the system image are moved to c:. How can I determine what they are? Is it because c: and e: are partitions of the same disk? If I move c: tro a different disk will that mean I only have to back up c:? Thanks Edit 2: I have viewed all files including hidden and system ones on both drives and it seems that I have a suspicous hidden e:\boot\ folder. I think that I might have installed the OS as a VHD at first then installed a seperate version straight on the disk, having dual boot for a while, then used EasyBCD to remove the VHD boot and file. Might this be what is causing my issue? How might I go about removing this? is it safe to just delete the boot folder?

  Read the article

• Lenovo Ideapad Y480 can't reinstall windows?

  - by elegantonyx

  Alright, so here's the deal... For a while, I wanted to mess with Linux. I don't know why, but I wanted to. So, what I did was use WUBI and install Ubuntu. Because of some unknown reason (Intel Rapid Start? Half the drivers being on a Lenovo-installed SSD [separate from the main hard drive]?) it wouldn't dual boot. So, I decided to use Linux Mint instead, and install it in a partition. Since Windows 7 Home Premium won't make partitions any more if you have a certain number already, I just shrank my system drive and left empty space for the installer to claim. When I installed Mint, it worked, but left my Windows 7 installation unable to boot and eventually it corrupted. I tried to use a system repair disc I burned earlier but it didn't find the Windows installation, so I assume the partition corrupted. I used this link:http://www.pcworld.com/article/248995/how_to_install_windows_7_without_the_disc.html to try and reinstall Windows. What happened was that originally it said that the partition I was trying to reinstall from had been locked down by the OEM (Lenovo). So, I went into GParted, wiped EVERYTHING, and selected 'Construct new Boot record' or whatever that function is, and now the error is: "Setup was unable to create a new system partition or locate an existing system partition. See the setup log files for more information." Does anyone know how to see the log files? Can anyone help? This system is a month old but the warranty only covers hardware failures, and I would need to pay around USD$60 for them to fix it. Please help. Any ideas? this is my main machine... Extra information: I have at my disposal: System Repair Disc (Burned myself) Windows 7 Home Premium 64 bit SP1 installation disk (burned from the pcworld links) Gparted Live CD Linux Mint 13 live cd A system backup (from the morning before this catastrophe) made using the Windows Backup and Restore. I put it on an external drive...that should be safe for now.

  Read the article

• Windows Service HTTPListener Memory Issue

  - by crawshaws

  Hi all, Im a complete novice to the "best practices" etc of writing in any code. I tend to just write it an if it works, why fix it. Well, this way of working is landing me in some hot water. I am writing a simple windows service to server a single webpage. (This service will be incorperated in to another project which monitors the services and some folders on a group of servers.) My problem is that whenever a request is recieved, the memory usage jumps up by a few K per request and keeps qoing up on every request. Now ive found that by putting GC.Collect in the mix it stops at a certain number but im sure its not meant to be used this way. I was wondering if i am missing something or not doing something i should to free up memory. Here is the code: Public Class SimpleWebService : Inherits ServiceBase 'Set the values for the different event log types. Public Const EVENT_ERROR As Integer = 1 Public Const EVENT_WARNING As Integer = 2 Public Const EVENT_INFORMATION As Integer = 4 Public listenerThread As Thread Dim HTTPListner As HttpListener Dim blnKeepAlive As Boolean = True Shared Sub Main() Dim ServicesToRun As ServiceBase() ServicesToRun = New ServiceBase() {New SimpleWebService()} ServiceBase.Run(ServicesToRun) End Sub Protected Overrides Sub OnStart(ByVal args As String()) If Not HttpListener.IsSupported Then CreateEventLogEntry("Windows XP SP2, Server 2003, or higher is required to " & "use the HttpListener class.") Me.Stop() End If Try listenerThread = New Thread(AddressOf ListenForConnections) listenerThread.Start() Catch ex As Exception CreateEventLogEntry(ex.Message) End Try End Sub Protected Overrides Sub OnStop() blnKeepAlive = False End Sub Private Sub CreateEventLogEntry(ByRef strEventContent As String) Dim sSource As String Dim sLog As String sSource = "Service1" sLog = "Application" If Not EventLog.SourceExists(sSource) Then EventLog.CreateEventSource(sSource, sLog) End If Dim ELog As New EventLog(sLog, ".", sSource) ELog.WriteEntry(strEventContent) End Sub Public Sub ListenForConnections() HTTPListner = New HttpListener HTTPListner.Prefixes.Add("http://*:1986/") HTTPListner.Start() Do While blnKeepAlive Dim ctx As HttpListenerContext = HTTPListner.GetContext() Dim HandlerThread As Thread = New Thread(AddressOf ProcessRequest) HandlerThread.Start(ctx) HandlerThread = Nothing Loop HTTPListner.Stop() End Sub Private Sub ProcessRequest(ByVal ctx As HttpListenerContext) Dim sb As StringBuilder = New StringBuilder sb.Append("<html><body><h1>Test My Service</h1>") sb.Append("</body></html>") Dim buffer() As Byte = Encoding.UTF8.GetBytes(sb.ToString) ctx.Response.ContentLength64 = buffer.Length ctx.Response.OutputStream.Write(buffer, 0, buffer.Length) ctx.Response.OutputStream.Close() ctx.Response.Close() sb = Nothing buffer = Nothing ctx = Nothing 'This line seems to keep the mem leak down 'System.GC.Collect() End Sub End Class Please feel free to critisise and tear the code apart but please BE KIND. I have admitted I dont tend to follow the best practice when it comes to coding.

  Read the article

• Ubuntu Newbie Needs Assistance!!

  - by Steve Greene

  New Ubuntu User Needs Help!- version 9.10 does not communicate with laptop Hello folks, Several days ago, I installed Ubuntu 9.10 onto my Acer Aspire 3100 laptop, running it alongside Widows Vista as a dual-bootable system. Creation of the Ubuntu boot CD went fine, and the installation onto my hard drive was flawless. Ubuntu opens and behaves as I would expect, except for one little problem. For reasons unknown to me, Ubuntu is not communicating with my laptop's networking hardware, and I have no internet connectivity, even when sitting directly under the wireless router at the local library (literally), which puts out a wickedly-fast signal that my Windows Vista OS auto-detects and immediately connects to. Up in the right side of the Ubuntu desktop, I click on the network icon and it does not show a wireless connection at all, even though I am only a few feet from the router. At home, where I use a dialup modem, I also see no means of getting online. My modem is an HDAUDIO Soft Data Fax Modem with Smart CP,manufactured by CXT (Conexant Systems Inc., file version 4.0.13.0, and the driver version is 7.58.0.0). I desparately wish to convert to Ubuntu. I used Mac for ten years, and then Windows for ten years. Now, after 20 years, I want to live out my days as an open-source Ubuntu fanatic. I am ready to give the old status quo the boot! I am an advanced computer user, but I am not a programmer. I seek a solution that is user-friendly for normal people, something equivalent to a driver that I can easily install or activate that will allow Ubuntu to see my hardware and get me connected. Can anyone help me over this hopefully-little glitch so that I can move on in total Ubuntu bliss? My processor is a Mobile AMD Sempron Processor 3500+ at 1.80 GHz, 1.50 GB RAM, and a 32-bit Operating System. I am running Windows Vista Home Basic, Service Pack 2. My current email is [email protected] if you have a workable solution that does not require programmer status to implement. Surely this must be a simple fix that I simply am overlooking, but being the new guy on the block, I have yet to be enlightened. Thanks for your help in coming up to speed!! Steve Wanna' be Ubuntu Fanatic "If you're not living on the edge, you're taking up too much space."

  Read the article

• networking tunnel adapter connections?

  - by Karthik Balaguru

  I understand that Tunnel Adapter LAN is for encapsulating IPv6 packets with an IPv4 header so that they can be sent across an IPv4 network. Few queries popped up in my mind based on this :- If i do 'ipconfig', Apart from ethernet adapter LAN details, I get a series of statments as below - Tunnel adapter Local Area Connection* 6 Tunnel adapter Local Area Connection* 7 Tunnel adapter Local Area Connection* 12 Tunnel adapter Local Area Connection* 13 Tunnel adapter Local Area Connection* 14 Tunnel adapter Local Area Connection* 15 Tunnel adapter Local Area Connection* 16 Except for the *16, all the other Tunnel Adapter Local Area Connections show Media Disconnected. Why is the numbering for the Tunnel adapter LAN not sequential? It is like 6, 7, 12, 13, 14, 15, 16. A strange numbering scheme! I tried to figure it out by thinking of some arithmetic series. But, it does not seem to fit in. There is a huge gap between 7 and 12. Any ideas? What is the need for so many Tunnel Adapter LAN connections? Can you tell me a scenario that requires all of those ? I did ipconfig /all to get more information. From the listing, I understand that: 16, 15, 14, 12 are Microsoft 6to4 Adapters 13, 6 are isatap Adapters 7 is Teredo Tunneling Pseudo-interface I understand that the above are for automatic tunneling so that the tunnel endpoints are determined automatically by the routing infrastructure. 6to4 is recommended by RFC3056 for automatic tunneling that uses protocol 41 for encapsulation. It is typically used when an end-user wants to connect to the IPv6 Internet using their existing IPv4 connection. Teredo is an automatic tunneling technique that uses UDP encapsulation across multiple NATs. That is, It is to grant IPv6 connectivity to nodes that are located behind IPv6-unaware NAT devices ISATAP treats the IPv4 network as a virtual IPv6 local link, with mappings from each IPv4 address to a link-local IPv6 address. That is to transmit IPv6 packets between dual-stack nodes on top of an IPv4 network. That is, to put in simple words, ISATAP is an intra-site mechanism, while the 6to4 and Teredo are for inter-site tunnelling mechanisms. It seems that Teredo should alone enabled by default in Vista, But my system does not show it to be enabled by default. Interestingly, it shows a 6to4 tunnel adapter (Tunnel adapter LAN connection 16) to be enabled by default? Any specific reasons for it? If i do ipconfig /all, why is only one Teredo present while four 6to4 are present ? I searched the internet for answers to the above queries, but I am unable to find clear answers.

  Read the article

• Facing Memory Leaks in AES Encryption Method.

  - by Mubashar Ahmad

  Can anyone please identify is there any possible memory leaks in following code. I have tried with .Net Memory Profiler and it says "CreateEncryptor" and some other functions are leaving unmanaged memory leaks as I have confirmed this using Performance Monitors. but there are already dispose, clear, close calls are placed wherever possible please advise me accordingly. its a been urgent. public static string Encrypt(string plainText, string key) { //Set up the encryption objects byte[] encryptedBytes = null; using (AesCryptoServiceProvider acsp = GetProvider(Encoding.UTF8.GetBytes(key))) { byte[] sourceBytes = Encoding.UTF8.GetBytes(plainText); using (ICryptoTransform ictE = acsp.CreateEncryptor()) { //Set up stream to contain the encryption using (MemoryStream msS = new MemoryStream()) { //Perform the encrpytion, storing output into the stream using (CryptoStream csS = new CryptoStream(msS, ictE, CryptoStreamMode.Write)) { csS.Write(sourceBytes, 0, sourceBytes.Length); csS.FlushFinalBlock(); //sourceBytes are now encrypted as an array of secure bytes encryptedBytes = msS.ToArray(); //.ToArray() is important, don't mess with the buffer csS.Close(); } msS.Close(); } } acsp.Clear(); } //return the encrypted bytes as a BASE64 encoded string return Convert.ToBase64String(encryptedBytes); } private static AesCryptoServiceProvider GetProvider(byte[] key) { AesCryptoServiceProvider result = new AesCryptoServiceProvider(); result.BlockSize = 128; result.KeySize = 256; result.Mode = CipherMode.CBC; result.Padding = PaddingMode.PKCS7; result.GenerateIV(); result.IV = new byte[] { 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 }; byte[] RealKey = GetKey(key, result); result.Key = RealKey; // result.IV = RealKey; return result; } private static byte[] GetKey(byte[] suggestedKey, SymmetricAlgorithm p) { byte[] kRaw = suggestedKey; List<byte> kList = new List<byte>(); for (int i = 0; i < p.LegalKeySizes[0].MaxSize; i += 8) { kList.Add(kRaw[(i / 8) % kRaw.Length]); } byte[] k = kList.ToArray(); return k; }

  Read the article

• Optimal setup for ASUS P6X58D Premium BIOS (no OC)?

  - by rumtscho

  Normally, I'd trust the mainboard manufacturer to choose the best options as defaults. But I had trouble with the board, because even with Quick Boot enabled, it booted twice as slowly as a Pentium 4 Celeron. Then I changed lots of options at once (most of them weren't explained in the manual, just mentioned with a single sentence) and the boot time is only marginally worse than the Pentium 4 (54 sec against 46 sec from button to pw entering screen). Now I don't know if I have turned something off which should have stayed on. I guess I even won't be able to boot from a CD now, because even though it is present in the boot sequence, I took off a timeout I think it needs to check whether there is a disk in the drive. The second reason is that I don't have an internal HDD, only a SSD. I forgot my sources blush but I am under the impression that today's BIOS and OS options are geared toward booting from a HDD, which is often less than optimal when one boots from a SSD, especially when there are functions which cause avoidable writing cycles, as a SSD wears out after too many writing cycles. Most of the things I've read concern the OS, but there are some BIOS-relevant options too. I am especially confused about the disk mode. The board supports AHCI, IDE-simulation and RAID, but of the different articles I've read, there is a proponent for each and no clear arguments for any. So can one tell me which options are important in general and which are important for a SSD-only system? I don't want to overclock the CPU, so you don't have to say anything about this (yes I know the board is meant for OC:)). I am thinking of overclocking the RAM, since they sold me 1600er heatsinked modules which are running at 1066 now, but I'm not sure yet about that. The rest of the system: i7-930, Intel X25-m G2, 6 GB RAM, GTS 250, some no-name Blue-ray ROM. 2 external HDDs over USB 2.0. Lots of other USB-connected hardware (12 devices I think), no SATA 3 drives (will disabling the controller have an impact on performance?), no LAN, only WiFi. Lucid Lynx 64 bit, no dual boot, no virtual installations. The main uses of the system are: managing and playing/showing all the media stored on the external disks, lots of image manipulation, some video editing, a bit of (non-demanding) gaming, rarely development. Lots of Internet surfing too, but this shouldn't have much impact on performance.

  Read the article

• Do you still limit line length in code?

  - by Noldorin

  This is a matter on which I would like to gauge the opinion of the community: Do you still limit the length of lines of code to a fixed maximum? This was certainly a convention of the past for many languages; one would typically cap the number of characters per line to a value such as 80 (and more recnetly 100 or 120 I believe). As far as I understand, the primary reasons for limiting line length are: Readability - You don't have to scroll over horizontally when you want to see the end of some lines. Printing - Admittedly (at least in my experience), most code that you are working on does not get printed out on paper, but by limiting the number of characters you can insure that formatting doesn't get messed up when printed. Past editors (?) - Not sure about this one, but I suspect that at some point in the distant past of programming, (at least some) text editors may have been based on a fixed-width buffer. I'm sure there are points that I am still missing out, so feel free to add to these... Now, when I tend to observe C or C# code nowadays, I often see a number of different styles, the main ones being: Line length capped to 80, 100, or even 120 characters. As far as I understand, 80 is the traditional length, but the longer ones of 100 and 120 have appeared because of the widespread use of high resolutions and widescreen monitors nowadays. No line length capping at all. This tends to be pretty horrible to read, and I don't see it too often, though it's certainly not too rare either. Inconsistent capping of line length. The length of some lines are limited to a fixed maximum (or even a maximum that changes depending on the file/location in code), while others (possibly comments) are not at all. My personal preference here (at least recently) has been to cap the line length to 100 in the Visual Studio editor. This means that in a decently sized window (on a non-widescreen monitor), the ends of lines are still fully visible. I can however see a few disadvantages in this, especially when you end up writing code that's indented 3 or 4 levels and then having to include a long string literal - though I often take this as a sign to refactor my code! In particular, I am curious what the C and C# coders (or anyone who uses Visual Studio for that matter) think about this point, though I would be interested in hearing anyone's thoughts on the subject. Edit Thanks for the all answers - I appreciate the variety of opinions here, all presenting sound reasons. Consensus does seem to be tipping in the direction of always (or almost always) limit the line length. Interestingly, it seems to be in various coding standards to limit the line length. Judging by some of the answers, both the Python and Google CPP guidelines set the limit at 80 chars. I haven't seen anything similar regarding C# or VB.NET, but I would be curious to see if there are ones anywhere.

  Read the article

• TcpListener is queuing connections faster than I can clear them

  - by Matthew Brindley

  As I understand it, TcpListener will queue connections once you call Start(). Each time you call AcceptTcpClient (or BeginAcceptTcpClient), it will dequeue one item from the queue. If we load test our TcpListener app by sending 1,000 connections to it at once, the queue builds far faster than we can clear it, leading (eventually) to timeouts from the client because it didn't get a response because its connection was still in the queue. However, the server doesn't appear to be under much pressure, our app isn't consuming much CPU time and the other monitored resources on the machine aren't breaking a sweat. It feels like we're not running efficiently enough right now. We're calling BeginAcceptTcpListener and then immediately handing over to a ThreadPool thread to actually do the work, then calling BeginAcceptTcpClient again. The work involved doesn't seem to put any pressure on the machine, it's basically just a 3 second sleep followed by a dictionary lookup and then a 100 byte write to the TcpClient's stream. Here's the TcpListener code we're using: // Thread signal. private static ManualResetEvent tcpClientConnected = new ManualResetEvent(false); public void DoBeginAcceptTcpClient(TcpListener listener) { // Set the event to nonsignaled state. tcpClientConnected.Reset(); listener.BeginAcceptTcpClient( new AsyncCallback(DoAcceptTcpClientCallback), listener); // Wait for signal tcpClientConnected.WaitOne(); } public void DoAcceptTcpClientCallback(IAsyncResult ar) { // Get the listener that handles the client request, and the TcpClient TcpListener listener = (TcpListener)ar.AsyncState; TcpClient client = listener.EndAcceptTcpClient(ar); if (inProduction) ThreadPool.QueueUserWorkItem(state => HandleTcpRequest(client, serverCertificate)); // With SSL else ThreadPool.QueueUserWorkItem(state => HandleTcpRequest(client)); // Without SSL // Signal the calling thread to continue. tcpClientConnected.Set(); } public void Start() { currentHandledRequests = 0; tcpListener = new TcpListener(IPAddress.Any, 10000); try { tcpListener.Start(); while (true) DoBeginAcceptTcpClient(tcpListener); } catch (SocketException) { // The TcpListener is shutting down, exit gracefully CheckBuffer(); return; } } I'm assuming the answer will be related to using Sockets instead of TcpListener, or at least using TcpListener.AcceptSocket, but I wondered how we'd go about doing that? One idea we had was to call AcceptTcpClient and immediately Enqueue the TcpClient into one of multiple Queue<TcpClient> objects. That way, we could poll those queues on separate threads (one queue per thread), without running into monitors that might block the thread while waiting for other Dequeue operations. Each queue thread could then use ThreadPool.QueueUserWorkItem to have the work done in a ThreadPool thread and then move onto dequeuing the next TcpClient in its queue. Would you recommend this approach, or is our problem that we're using TcpListener and no amount of rapid dequeueing is going to fix that?

  Read the article

• Windows 7 The boot selection failed because a required device is inaccessible 0xc000000f

  - by piratejackus

  I have a problem with my Windows 7, hardware : Acer 3820TG Operating Systems : Windows 7 and Ubuntu 10.04 dual Case: When I try to boot my windows 7 I see an error: "Window failed to start. A recent hardware or software change might be the cause. To fix the problem: 1.Insert.... 2. .... ... status : 0xc000000f info : The boot selection failed because a required device is inaccessible .... " I can't exactly remember what were my last actions on Windows. I already searched this error and applied the proposed solutions, I created a repair USB (because I don't have a CD-ROM nor a Windows 7 CD) such as; -repair operating system :it says it cannot repair it -checking disk (chkdsk D: /f /r) : it checks the disk without a problem or error and it takes pretty long (more than a hour). But when I restart, still the same error. -I didn't create a restore point so I pass this option -I don't have a system image -I tried to run windows recovery (I have a recovery partition) but there are just two options: 1- Format the operating system but retain user data (copies the files under users to c\backup folder, but when I searched deeper I found that there are some people who already tried this option and couldn't find their user files under backup directory). Plus, I have unfortunately just one partition D (it is a fault I know) because I use always Ubuntu. So this is not applicable in my situation 2- Format entire system (Windows). I keep my valuable data in windows but not in user folder. I was reaching them from Windows. -I tried to repair windows boot by: bootrec /fixMBR bootrec /fixBoot bootrec /rebuildBCD I lost all grub menu, and reinstalled it. - ubuntuforums.org/showthread.php?t=1014708&page=29 nothing changed, same error. I created a thread in microsoft forums - http://social.answers.microsoft.com/Forums/en-US/w7install/thread/69517faf-850a-45fd- 8195-6d4ed831f805 but I couldn't find a solution. Before I run chkdsk from usb repair disk I couldn't able to mount Windows (NTFS) partition from Ubuntu, I was getting "couldn't mount file system, error code 2". I tried to fix ntfs partition from ubuntu and got "segmentation fault". I also created a thread on ubuntuforums for this mount problem: - http://ubuntuforums.org/showthread.php?t=1606427 So, after chkdsk, I could enable to mount windows partition but all I see in this partition is chkdsk logs, no any other data. Now, I don't think I lost my data because I don't get any filesystem errors, just the boot section, but this log files under windows partition makes me afraid. I see that Microsoft developers don't have a solution yet for this error. If you need any information to get more idea I can give, maybe I miss some points or it could be complicated. Thanks in advance.

  Read the article

• Vagrant - Failed login, ssh not set up

  - by motleydev

  This question is two fold because somewhere in my attempts to solve the problem, I created a new one. First: I was trying to vagrant up using a Vagranfile based on the standard hashicorp/precise32 box. Everything worked up until default: SSH auth method: private key where it would eventually time out. Enabling gui in the Vagrantfile showed that the machine never actually logs in. I can use the standard user/pass and log in from that point but the vagrant up process still remains at that prior status. Here's where my understanding might be a little dim. I've tried setting auth method from the insecure_pass_key to my root ~/.ssh/id_rsa or whichever one I wanted to use. I'm not entirely sure where to put a copy of the public key or my authorized keys file. I've got a .vagrant.d folder in my user dir (I'm on OSX) which seems to contain the box images. I've got a .vagrant folder in my directory with the Vagrantfile which seems to contain the specific machine I am building off of. I've tried pouring over the docs and forums but I seem to be missing a key concept here. And Now: After a host of tips/tricks such as rolling back by VirtualBox install, uninstalling/reinstalling Vagrant and VritualBox several times, when I try to run vagrant ssh-config with a Vagrantfile based on the same hashicorp/precise32 it says that the box is not enabled for SSH. Specifically, this error: The provider for this Vagrant-managed machine is reporting that it is not yet ready for SSH. Depending on your provider this can carry different meanings. Make sure your machine is created and running and try again. Additionally, check the output of `vagrant status` to verify that the machine is in the state that you expect. If you continue to get this error message, please view the documentation for the provider you're using. So now I am slightly up a creek. Any help would be appreciated if not just clarifying a concept. Some pertinent info: I'm on OSX Maverics Due to the fact I'm running a dual HD system with system files on one HD and user files on another, my permissions are a little wonky and VBoxManage will only let me run commands via Sudo - not sure if it's pertinent - but maybe. I have no idea what I'm doing. That part is perhaps more important.

  Read the article

• networking tunnel adapter connections?

  - by Karthik Balaguru

  I understand that Tunnel Adapter LAN is for encapsulating IPv6 packets with an IPv4 header so that they can be sent across an IPv4 network. Few queries popped up in my mind based on this :- If i do 'ipconfig', Apart from ethernet adapter LAN details, I get a series of statments as below - Tunnel adapter Local Area Connection* 6 Tunnel adapter Local Area Connection* 7 Tunnel adapter Local Area Connection* 12 Tunnel adapter Local Area Connection* 13 Tunnel adapter Local Area Connection* 14 Tunnel adapter Local Area Connection* 15 Tunnel adapter Local Area Connection* 16 Except for the *16, all the other Tunnel Adapter Local Area Connections show Media Disconnected. Why is the numbering for the Tunnel adapter LAN not sequential? It is like 6, 7, 12, 13, 14, 15, 16. A strange numbering scheme! I tried to figure it out by thinking of some arithmetic series. But, it does not seem to fit in. There is a huge gap between 7 and 12. Any ideas? What is the need for so many Tunnel Adapter LAN connections? Can you tell me a scenario that requires all of those ? I did ipconfig /all to get more information. From the listing, I understand that: 16, 15, 14, 12 are Microsoft 6to4 Adapters 13, 6 are isatap Adapters 7 is Teredo Tunneling Pseudo-interface I understand that the above are for automatic tunneling so that the tunnel endpoints are determined automatically by the routing infrastructure. 6to4 is recommended by RFC3056 for automatic tunneling that uses protocol 41 for encapsulation. It is typically used when an end-user wants to connect to the IPv6 Internet using their existing IPv4 connection. Teredo is an automatic tunneling technique that uses UDP encapsulation across multiple NATs. That is, It is to grant IPv6 connectivity to nodes that are located behind IPv6-unaware NAT devices ISATAP treats the IPv4 network as a virtual IPv6 local link, with mappings from each IPv4 address to a link-local IPv6 address. That is to transmit IPv6 packets between dual-stack nodes on top of an IPv4 network. That is, to put in simple words, ISATAP is an intra-site mechanism, while the 6to4 and Teredo are for inter-site tunnelling mechanisms. It seems that Teredo should alone enabled by default in Vista, But my system does not show it to be enabled by default. Interestingly, it shows a 6to4 tunnel adapter (Tunnel adapter LAN connection 16) to be enabled by default? Any specific reasons for it? If i do ipconfig /all, why is only one Teredo present while four 6to4 are present ? I searched the internet for answers to the above queries, but I am unable to find clear answers.

  Read the article

• Disk IO causing high load on Xen/CentOS guest

  - by Peter Lindqvist

  I'm having serious issues with a xen based server, this is on the guest partition. It's a paravirtualized CentOS 5.5. The following numbers are taken from top while copying a large file over the network. If i copy the file another time the speed decreases in relation to load average. So the second time it's half the speed of the first time. It needs some time to cool off after this. Load average slowly decreases until it's once again usable. ls / takes about 30 seconds. top - 13:26:44 up 13 days, 21:44, 2 users, load average: 7.03, 5.08, 3.15 Tasks: 134 total, 2 running, 132 sleeping, 0 stopped, 0 zombie Cpu(s): 0.0%us, 0.1%sy, 0.0%ni, 25.3%id, 74.5%wa, 0.0%hi, 0.0%si, 0.1%st Mem: 1048752k total, 1041460k used, 7292k free, 3116k buffers Swap: 2129912k total, 40k used, 2129872k free, 904740k cached PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND 1506 root 10 -5 0 0 0 S 0.3 0.0 0:03.94 cifsd 1 root 15 0 2172 644 556 S 0.0 0.1 0:00.08 init Meanwhile the host is ~0.5 load avg and steady over time. ~50% wait Server hardware is dual xeon, 3gb ram, 170gb scsi 320 10k rpm, and shouldn't have any problems with copying files over the network. disk = [ "tap:aio:/vm/dev01.img,xvda,w" ] I also get these in the log INFO: task syslogd:1350 blocked for more than 120 seconds. "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. syslogd D 00062E4F 2208 1350 1 1353 1312 (NOTLB) c0ef0ed0 00000286 6e71a411 00062e4f c0ef0f18 00000009 c0f20000 6e738bfd 00062e4f 0001e7ec c0f2010c c181a724 c1abd200 00000000 ffffffff c0ef0ecc c041a180 00000000 c0ef0ed8 c03d6a50 00000000 00000000 c03d6a00 00000000 Call Trace: [<c041a180>] __wake_up+0x2a/0x3d [<ee06a1ea>] log_wait_commit+0x80/0xc7 [jbd] [<c043128b>] autoremove_wake_function+0x0/0x2d [<ee065661>] journal_stop+0x195/0x1ba [jbd] [<c0490a32>] __writeback_single_inode+0x1a3/0x2af [<c04568ea>] do_writepages+0x2b/0x32 [<c045239b>] __filemap_fdatawrite_range+0x66/0x72 [<c04910ce>] sync_inode+0x19/0x24 [<ee09b007>] ext3_sync_file+0xaf/0xc4 [ext3] [<c047426f>] do_fsync+0x41/0x83 [<c04742ce>] __do_fsync+0x1d/0x2b [<c0405413>] syscall_call+0x7/0xb ======================= I have tried disabling irqbalanced as suggested here but it does not seem to make any difference.

  Read the article

• Why is my new Phenom II 965 BE not significantly faster than my old Athlon 64 X2 4600+?

  - by Software Monkey

  I recently rebuilt my 5 year old computer. I upgraded all core components, in particular from an Athlon 64 X2 4600+ at 2.4 GHz with DDR2 800 to a Phenom II 965 BE (quad core) at 3.6 GHz with DDR3 1333 (actually 1600, but testing consistently detected memory errors at 1600). The motherboard is also much newer and better. The HDD's (x3), DVD writer and card reader are the same. The BIOS memory config is auto-everything except the base timing which I overrode to 1T instead of 2T. The BIOS CPU multiplier is slightly over-clocked to 3.6 GHz from the stock 3.4 GHz. I noticed compiling Java is slower than I expected. As it happens I have some (single-threaded) Java pattern-matching code which is CPU and memory bound and for which I have performance numbers recorded on a number of hardware platforms, including my old system. So I did a test run on the new equipment and was stunned to find that the numbers are only slightly better than my old system, about 25%. The data set it is operating on is a 148,975 character array, which should easily fit in caches, but in any event the new CPU has larger caches all around. The system was, of course, otherwise idle for the test and the test run is a timed 10 seconds to eliminate scheduling anomalies. A long while ago, when I upgraded only memory from DD2 667 to DDR2 800 there was no change in performance of this test, which subjectively supports that the test cycle does not need to (significantly) access main memory, but yes it is creating and garbage collecting a large number of objects in the process of this test (low millions of matches are found for the pattern set). I am about 99.999% certain the code hasn't changed since I last ran it on 2009-03-17 - but I can't easily retest the old hardware, because it is currently in pieces on my work-bench waiting to be built into a new computer for my kids. Note that Windows (XP) reports a CPU speed of 795 MHz unless I have some thing running. With stuff running it seems to jump all over the place each time I use ALT-Pause to display the system properties, everywhere from 795 MHz to 3.4 Ghz. So why might my shiny new hardware under-performing so badly? EDIT: The old memory was Mushkin DDR2 800 with timings set for auto which should have been 5-5-5-12. The new memory is Corsair DDR3 1600, running at 1333 with timings also auto which are 9-9-9-21. In both cases they are a paired set of dual channel DIMMs. I was waiting to ensure my system was stable before tweaking with memory timings.

  Read the article

• JNDI Datasource Problem on Tomcat 6, Hibernate

  - by Asuman AKYILDIZ

  Hello; I am using Tomcat 6 as application server, Struts-Hibernate and MyEclipse 6.0. My application uses JDBC driver but I should modify it to use JNDI Datasource. I followed steps as described in tomcat 6.0 howto tutorial. I defined my resource in tomcatconf: <Resource name="jdbc/ats" global="jdbc/ats" auth="Container" type="javax.sql.DataSource" driverClassName="oracle.jdbc.OracleDriver" url="jdbc:oracle:thin:@//localhost:1521/MISDEV" username="TEST" password="TEST" maxActive="20" maxIdle="10" maxWait="-1" validationQuery="SELECT 1 from dual" removeAbandoned="true" removeAbandonedTimeout="30" logAbandoned="false"/> I gave reference in my application web.xml: <resource-ref> <description>Oracle Datasource example</description> <res-ref-name>jdbc/ats</res-ref-name> <res-type>javax.sql.DataSource</res-type> <res-auth>Container</res-auth> </resource-ref> And I defined datasource-dialect in my hibernate-cfg.xml <property name="connection.datasource">java:comp/env/jdbc/ats</property> <property name="dialect">org.hibernate.dialect.Oracle9Dialect</property> But when I create hibernate session, it can not open the connection: 09:18:11,322 ERROR JDBCExceptionReporter:72 - Connections could not be acquired from the underlying database! org.hibernate.exception.GenericJDBCException: Cannot open connection I also tried to set the properties at runtime: Configuration configuration = new Configuration(); configuration.setProperty("hibernate.dialect", "org.hibernate.dialect.Oracle9Dialect"); //configuration.setProperty("hibernate.connection.datasource", "java:comp/env/jdbc/ats"); configuration.setProperty("hibernate.current_session_context_class", "thread"); configuration.setProperty("hibernate.connection.provider_class", "org.hibernate.connection.C3P0ConnectionProvider"); configuration.setProperty("hibernate.show_sql", "true"); sessionFactory = configuration.configure().buildSessionFactory(); It does not open connection again. But, when I use JDBC driver it works: Configuration configuration = new Configuration(); configuration.setProperty("hibernate.dialect", "org.hibernate.dialect.Oracle9Dialect"); //configuration.setProperty("hibernate.connection.datasource", "java:comp/env/jdbc/ats"); configuration.setProperty("hibernate.connection.url", "jdbc:oracle:thin:@//localhost:1521/MISDEV"); configuration.setProperty("hibernate.connection.username", "test"); configuration.setProperty("hibernate.connection.password", "test"); configuration.setProperty("hibernate.connection.driver_class", "oracle.jdbc.OracleDriver"); configuration.setProperty("hibernate.transaction.factory_class", "org.hibernate.transaction.JDBCTransactionFactory"); configuration.setProperty("hibernate.current_session_context_class", "thread"); configuration.setProperty("hibernate.connection.provider_class", "org.hibernate.connection.C3P0ConnectionProvider"); configuration.setProperty("hibernate.show_sql", "true"); sessionFactory = configuration.configure().buildSessionFactory(); I have been searching for 3 days and no success. What may be de problem?

  Read the article

• 64-bit linux kernel only seeing 3 of 4GB after upgrade...

  - by Blaine

  Hey everyone. I am running Ubuntu 9.04 64-bit on my macbook. I had 2GB of ram before, and everything ran great. I just upgraded to 2x2GB (4GB), but my system only sees 3GB of it. OS X, which I am dual booting, sees all 4GB. Also, my video performance is incredibly lacking. Before the upgrade my compiz benchmark was full at 80fps, and now it is at 22fps with very choppy window dragging. Has anyone ever heard of this on a 64-bit kernel? I just don't quite understand what could be the issue. 10$ uname -a Linux macbook 2.6.28-15-generic #49-Ubuntu SMP Tue Aug 18 19:25:34 UTC 2009 x86_64 GNU/Linux $ free -m total used free shared buffers cached Mem: 2953 1031 1921 0 114 427 -/+ buffers/cache: 489 2463 Swap: 7812 0 7812 9$ lsmod Module Size Used by i915 77960 2 drm 123232 3 i915 binfmt_misc 18572 1 ppdev 16904 0 btusb 21784 2 bridge 63776 0 stp 11140 1 bridge bnep 22912 2 vboxnetadp 109356 0 vboxnetflt 116972 0 vboxdrv 1721612 1 vboxnetflt uvcvideo 69640 0 compat_ioctl32 18304 1 uvcvideo videodev 45184 2 uvcvideo,compat_ioctl32 v4l1_compat 23940 2 uvcvideo,videodev lp 19588 0 parport 49584 2 ppdev,lp snd_hda_intel 557492 3 snd_pcm_oss 52352 0 snd_mixer_oss 24960 1 snd_pcm_oss snd_pcm 99464 2 snd_hda_intel,snd_pcm_oss arc4 10240 2 snd_seq_dummy 11524 0 ecb 11392 2 snd_seq_oss 41984 0 snd_seq_midi 15744 0 snd_rawmidi 33920 1 snd_seq_midi snd_seq_midi_event 16512 2 snd_seq_oss,snd_seq_midi snd_seq 66272 6 snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_seq_midi_event ath9k 310584 0 snd_timer 34064 2 snd_pcm,snd_seq snd_seq_device 16276 5 snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_rawmidi,snd_seq mac80211 251528 1 ath9k iTCO_wdt 21712 0 iTCO_vendor_support 12420 1 iTCO_wdt joydev 20992 0 video 29204 0 snd 78920 15 snd_hda_intel,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_seq_oss,snd_rawmidi,snd_seq,snd_timer,snd_seq_device applesmc 37700 0 output 11648 1 video soundcore 16800 1 snd pcspkr 11136 0 cfg80211 43680 1 mac80211 appletouch 19972 0 isight_firmware 11520 0 input_polldev 12688 1 applesmc intel_agp 39408 1 snd_page_alloc 18704 2 snd_hda_intel,snd_pcm led_class 13064 2 ath9k,applesmc hid_apple 15872 0 usbhid 47040 0 ohci1394 42164 0 ieee1394 108288 1 ohci1394 sky2 63364 0 fbcon 49792 0 tileblit 11264 1 fbcon font 17024 1 fbcon bitblit 14464 1 fbcon softcursor 10368 1 bitblit Some information from dmesg: [ 795.820163] ACPI: EC: GPE storm detected, transactions will use polling mode [ 1762.709516] [drm:i915_getparam] *ERROR* Unknown parameter 6 [ 1763.078130] [drm:i915_getparam] *ERROR* Unknown parameter 6 [ 2362.760889] [drm:i915_getparam] *ERROR* Unknown parameter 6 [ 2416.352084] ACPI: EC: missing confirmations, switch off interrupt mode. [ 3718.721095] [drm:i915_getparam] *ERROR* Unknown parameter 6 [ 3719.108914] [drm:i915_getparam] *ERROR* Unknown parameter 6 [ 4318.773266] [drm:i915_getparam] *ERROR* Unknown parameter 6 [ 9513.813066] CE: hpet increasing min_delta_ns to 15000 nsec [ 9693.815684] npviewer.bin[6736]

  Read the article

• lacp, cicso 3550, 3560, help with configuration

  - by Flamewires

  Hey all this is a repost from a question I asked on the cisco forums but never got a useful reply. Hey I'm trying to convert the FreeBSD servers at work to dual-gig lagg links from regular gigabit links. Our production servers are on a 3560. I have a small test environment on a 3550. I have achieved fail-over, but am having troubles achieving the speed increase. All servers are running gig intel (em) cards. The configs for the servers are: BSDServer: #!/bin/sh #bring up both interfaces ifconfig em0 up media 1000baseTX mediaopt full-duplex ifconfig em1 up media 1000baseTX mediaopt full-duplex #create the lagg interface ifconfig lagg0 create #set lagg0's protocol to lacp, add both cards to the interface, #and assign it em1's ip/netmask ifconfig lagg0 laggproto lacp laggport em0 laggport em1 ***.***.***.*** netmask 255.255.255.0 The switches are configured as follows: #clear out old junk no int Po1 default int range GigabitEthernet 0/15 - 16 # config ports interface range GigabitEthernet 0/15 - 16 description lagg-test switchport duplex full speed 1000 switchport access vlan 192 spanning-tree portfast channel-group 1 mode active channel-protocol lacp **** switchport trunk encapsulation dot1q **** no shutdown exit interface Port-channel 1 description lagginterface switchport access vlan 192 exit port-channel load-balance src-mac end obviously change 1000's to 100's and GigabitEthernet to FastEthernet for the 3550's config, as that switch has 100Mbit speed ports. With this config on the 3550, I get failover and 92Mbits/sec speed on both links, simultaneously, connecting to 2 hosts.(tested with iperf) Success. However this is only with the "switchport trunk encapsulation dot1q" line. First, I do not understand why I need this, I thought it was only for connecting switches. Is there some other setting which this turns on that is actually responsible for the speed increase? Second, This config does not work on the 3560. I get failover, but not the speed increase. Speeds drop from gig/sec to 500Mbit/sec when I make 2 simultaneous connections to the server with or without the encapsulation line. I should mention that both switches are using source-mac load balancing. In my test I am using Iperf. I have the server(lagg box) setup as the server(iperf -s), and the client computers are client(iperf -c server-ip-address), so the source mac(and IP) are different for both connections. Any ideas/corrections/questions would be helpful, as the gig switches are what I actually need the lagg links on. Ask if you need more information.

  Read the article

• No login prompt displayed after updating Ubuntu 10.04, broken gdm

  - by cliff

  So here's what happens: I updated my system the other day, was prompted for a reboot for the update to complete but was in the middle of working so I delayed it until after I was done. I reboot and it's broken :(. It appears to boot normally, with the following exceptions: The purple Ubuntu load screen no longer displays (though it did for the first couple of times I tried to get in). I hear the login prompt sound, but no login prompt appears. Nor is it simply "invisible" - pressing enter, typing my password, and pressing enter again do nothing. Normally my Bluetooth mouse is functional at this point, but it is not. GRUB displays recovery options for my current kernel, and for an older one (2.6.32-24). Trying to boot into .32-24 gives me an error saying "udevadm can't do something while udev is not configured". So I try solutions listed here: http://superuser.com/questions/195786/ubuntu-update-went-wrong-pc-doesnt-boot-how-can-i-repair-it Nothing I tried seemed to work, and after further Googling my hunch is that it's a problem with gdm. Please correct me if I'm wrong, I don't know all that much about how Linux/Ubuntu systems work just yet. Things I'm able to do: Boot to a live CD Ctrl-Alt-F2 after that login sound plays brings me to a console login, which I can successfully do (it's how I tried the solutions above). This works only under the current kernel. A hack I'd be willing to explore is removing the login prompt from the console, but I'd prefer to "simply" fix what's wrong. Like that guy, I need to repair the system rather than reinstall. System: Dell Inspiron 1525 Core 2 Duo Proprietary Driver for Broadcom 43xx wireless Dual-boot with Windows 7 (which is how I'm posting this, unfortunately I only have this machine and any experimenting requires constant reboots into Windows/brokenbuntu) Last package installed was Moonlight, but it appeared to install properly. Kernel: 2.6.32-25 Edit: After working with Karl's suggestions, it seems that the problem is with gdm. Error exit status 245 when attempting to sudo apt-get install --reinstall gdm, also an error processing gdm when running sudo apt-get -f install. How do I reinstall or repair gdm so that I can get back into my machine?

  Read the article

• Why might one host be unable to access the Internet, when it can ping the router and when all other hosts can?

  - by user1444233

  I have a Draytek Vigor 2830n. It's kicking out a 192.168.3.0 LAN. It performs load-balancing across dual-WAN ports, although I've turned off the second WAN to simplify testing. There are many hosts on the LAN. All IPs are allocated through DHCP, most freely allocated from the pool, but one or two are bound to NIC MAC addresses. All hosts can access the Internet, save one. That host (192.168.3.100 or 'dot100' for short) gets allocated an IP address (and the right gateway address, DNS server addresses, subnet etc.) dot100 can ping itself. It can ping the gateway, and access the latter's web interface via port 80. It's responsive and loss-free (sustained ping over a couple of minutes reports no data loss). Yet, for some reason that evades me, dot100 can't ping an external IP address or domain name. I suspect it's never been able to, because it was getting some Internet access from a second adaptor (different subnet), but that's now been turned off, which exposed the problem. In dot100, I've tried: two operating systems (Windows 8 and Knoppix), to rule out anti-virus programs etc. two physical adaptors two cables, on each adaptor two IPs (e.g. .100 and .103 assigned by Mac and .26 from the pool) both dynamic and assigned (MAC-bound) DHCP-allocated IPs but none of this experiments yielded any variation in the result. dot100 is a crucial host. It's a file server for the network, so I need it to be reliably allocated a consistent IP. Can anyone offer a potential solution or a way forward with the analysis please? My guess My analysis so far leads me to believe it's a router issue. I've checked the web interface very carefully. There are no filters setup in Firewall - General Setup or Filter Setup. I suspect it's a corrupted internal routing table, but the web UI shows this as the Routing table: Key: C - connected, S - static, R - RIP, * - default, ~ - private * 0.0.0.0/ 0.0.0.0 via 62.XX.XX.X WAN1 * 62.XX.XX.X/ 255.255.255.255 via 62.XX.XX.X WAN1 S 82.YY.YYY.YYY/ 255.255.255.255 via 82.YY.YYY.YYY WAN1 C 192.168.1.0/ 255.255.255.0 directly connected WAN2 C~ 192.168.3.0/ 255.255.255.0 directly connected LAN2

  Read the article

• Finding the closest object in proxmity to the mouse Coordinates

  - by Cam

  Hey there, i've been working on a problem for a while now, which involves targeting the closest movieClip in relation to the x y coords of the mouse, I've attached a nice little acompanying graphic. Each mc added to the stage has it's own sub-class (HotSpots) which uses Pythag to measure distance from mouse. At this stage i can determine the closest value from my Main class but can't figure out how to reference it back to the movieclip... hope this makes sense. Below are the two Classes. My Main Class which attachs the mcs, and monitors mouse movement and traces closest value package { import flash.display.*; import flash.text.*; import flash.events.*; public class Main extends MovieClip { var pos:Number = 50; var nodeArray:Array; public function Main(){ nodeArray = []; for(var i:int = 0; i < 4; i++) { var hotSpot_mc:HotSpots = new HotSpots; hotSpot_mc.x += pos; hotSpot_mc.y += pos; addChild(hotSpot_mc); nodeArray.push(hotSpot_mc); // set some pos pos += 70; } stage.addEventListener(MouseEvent.MOUSE_MOVE,updateProxmity) } public function updateProxmity(e:MouseEvent):void { var tempArray:Array = new Array(); for(var i:int = 0; i < 4; i++) { this['tf'+[i]].text = String(nodeArray[i].dist); tempArray.push(nodeArray[i].dist); } tempArray.sort(Array.NUMERIC); var minValue:int = tempArray[0]; trace(minValue) } } } My HotSpots Class package { import flash.display.MovieClip; import flash.events.Event; import flash.text.TextField; public class HotSpots extends MovieClip { public var XSide:Number; public var YSide:Number; public var dist:Number = 0; public function HotSpots() { addEventListener(Event.ENTER_FRAME, textUp); } public function textUp(event:Event):void { XSide = this.x - MovieClip(root).mouseX; YSide = this.y - MovieClip(root).mouseY; dist = Math.round((Math.sqrt(XSide*XSide + YSide*YSide))); } } } thanks in advance

  Read the article

• Why is the server performance so poor? What can be done to improve the speed of the server?

  - by fslsyed

  Very slow processing using Windows Server2008 R2 Standard with Service Pack One. Situation: Read a text file using the text data to populate a series of MS Sql tables. The converted data is used to generate monthly PDF invoice files; the PDF files are saved directly to the hard drive. The application is multi-threading with one thread used for the text conversion and three threads for PDF invoice generation. The text conversion is occurring concurrently with the invoice generation. Application Software: C# using Microsoft Visual Studio 2010 Ultimate. Crystal Report Writer 2011 with runtime 13_0_3 64 bit version. Targeted platform is x64; also tested as x86, and Any CPU with similar results. Microsoft .NET Framework 4.0. Microsoft Sql 2008 Issue: The software is running very slowly. The conversion of the text file is approximately six hundred fifty records per second and generation of the PDF files is approximately twelve invoices per minute. The text file to be converted is six hundred Meg with seven thousand invoices to be generated. The software was installed on three different machines from the same distribution files. The same text file was converted on each machine. The user executing the application was an administrator on each machine. The only variances were the machine and operating system. The configurations are as follows: Server: Operating System: Windows Server2008 R2 Standard 64-bit (6.1, Build7601) SP1 Service Pack: System Manufacturer: IBM System Model: System x3550 M3-[7944AC1]- BIOS: Default System BIOS Processor: Intel® Xeon® CPU E5620@ 2.4GHz (16 CPUs) Memory: 16384MB Notebook: Operating System: Windows 7 Home Premium Standard 64-bit (6.1, Build7601) System Manufacturer: Hewlett-Packard System Model: HP Pavilion dv7 Notebook PC BIOS: Default System BIOS Processor: AMD Phenom II N640 Dual-Core Processor 2.9GHz (2 CPUs) Memory: 6144MB Desktop: Operating System: Windows 7 Professional 64-bit (6.1, Build7601) SP1 System Manufacturer: Dell Inc. System Model: OptiPlex 960 BIOS: Phoenix ROM BIOS PLUS Version 1.10 A11 Processor: Intel Core™2 Quad CPU Q9650 @3.00GHZ (4 CPUs) Memory: 16384MB Processing results per machine: The applications were executed seven times with the averages being displayed below. Machine Text Records Invoices Generated Converted Per Minute Per Minute Server (1) 650 12 Notebook 980 17 Desktop 2,100 45 (1) The server is dedicated to execution of this application; no additional applications are being executed. Question: Why is the server performance so poor? What can be done to improve the speed of the server?

  Read the article

• DirectShow EVR resizing window problem

  - by Daniel

  So I've been looking into the world of media playback for windows and I've started making a C# Media Player using DirectShow. I started off using the VRM-7 windowed video renderer and it was brilliant except it had a couple of small problems (multi monitors, fullscreen). But after some research I found that it's deprecated and I should be using VRM9. So I changed it to use VRM9 windowless then found out that was an old post rofl _< so finally I'm using Vista/Win7 (or XP .net 3) Enhanced Video Renderer (EVR) which is apparently the most up to date Microsoft video renderer and has all the flashy performance/quality things added to it. (tbh I haven't noticed any difference but maybe I need a blue-ray or HQ video to notice it). With using EVR everything is working fine except resizing the video. Its really laggy/choppy/teary and probably something to do with its frame queueing mechanism. To demonstrate my problem open up windows media player classic. View - Options - Playback - output Chose the "EVR" DirectShow Video renderer Now restart wmp class and play a video, while it's playing click and drag a corner to resize it. You'll notice its horribly laggy. This is the exact same problem i am having. But if you chose "EVR Custom Pres. *" or EVR Sync *" resizing works beautifully! So i tried googling around for anything about EVR resizing issues and how to fix it but i couldn't believe how little i could find. I'm guessing "Custom Pres." stands for "Custom Presenter" which sounds like they made their own. Also you'll notice on the right hand size when you swap between EVR and the other EVR's the Resizer drop down on the right greys out. So basically I wan't to know how I can fix this retarded resizing problem and is there any decent documentation out there? There is a fair bit for VMR7/9 but not much for EVR. I downloaded the DirectX SDK which apparently has samples but it was a waste of 500mb of bandwidth as it had nothing relevant. Perhaps there is some way to force it not queueing up frames if that is the problem? If you want code say the word and I'll paste some in. But it's really quite simple and nothing much happens, i'm convinced it's a problem with the EVR renderer. EDIT: Oh and one other thing, what does VLC use? If you go into vlc options and change the renderer to anything but default, they all suck. So is it using VMR7? Or its own?

  Read the article

• Different files on shared partition?

  - by Matt Robertson

  I am dual-booting Windows 8 and Ubuntu 12.04. My partition scheme looks like this: /dev/sda1 - Windows 8 (nfts) /dev/sda2 - Ubuntu / (ext4) /dev/sda3 - Ubuntu home (ext4) /dev/sda5 - swap /dev/sda6 - Shared data partition (exfat) (First off, yes I do have exfat libraries installed on Ubuntu) I created some PNG images in Windows and saved them on my shared partition. From Ubuntu, I edited the images in GIMP and saved them (replacing the ones on the shared partition). When I boot into Windows, the files appear unchanged - exactly like they did before I edited them from Ubuntu. I even added a folder and deleted some other files, but none of these changes exist in Windows. When I boot into Ubuntu, all of the changes are still there. It is as if Windows is caching the old file structure... How is this possible? Thanks in advance. Edit -- commands output ~~ lsblk NAME MAJ:MIN RM SIZE RO TYPE MOUNTPOINT sda 8:0 0 465.8G 0 disk +-sda1 8:1 0 165.1G 0 part +-sda2 8:2 0 21.3G 0 part / +-sda3 8:3 0 98.9G 0 part /home +-sda4 8:4 0 1K 0 part +-sda5 8:5 0 7.8G 0 part [SWAP] +-sda6 8:6 0 172.7G 0 part /mnt/shared_data ~~ /etc/fstab # <file system> <mount point> <type> <options> <dump> <pass> proc /proc proc nodev,noexec,nosuid 0 0 # /dev/sda2 UUID=8f700f65-b5c7-4afc-a6fb-8f9271e0fb5e / ext4 errors=remount-ro 0 1 # /dev/sda3 UUID=f0d688b7-22bd-4fa7-bc1b-a594af2933fa /home ext4 defaults 0 2 # /dev/sda5 UUID=3bc2399b-5deb-4f04-924b-d4fc77491997 none swap sw 0 0 # /dev/sda6 UUID=F2DE-BC47 /mnt/shared_data exfat defaults 0 3 ~~ /etc/mtab /dev/sda2 / ext4 rw,errors=remount-ro 0 0 proc /proc proc rw,noexec,nosuid,nodev 0 0 sysfs /sys sysfs rw,noexec,nosuid,nodev 0 0 none /sys/fs/fuse/connections fusectl rw 0 0 none /sys/kernel/debug debugfs rw 0 0 none /sys/kernel/security securityfs rw 0 0 udev /dev devtmpfs rw,mode=0755 0 0 devpts /dev/pts devpts rw,noexec,nosuid,gid=5,mode=0620 0 0 tmpfs /run tmpfs rw,noexec,nosuid,size=10%,mode=0755 0 0 none /run/lock tmpfs rw,noexec,nosuid,nodev,size=5242880 0 0 none /run/shm tmpfs rw,nosuid,nodev 0 0 /dev/sda3 /home ext4 rw 0 0 /dev/sda6 /mnt/shared_data fuseblk rw,nosuid,nodev,allow_other,blksize=4096 0 0 binfmt_misc /proc/sys/fs/binfmt_misc binfmt_misc rw,noexec,nosuid,nodev 0 0 gvfs-fuse-daemon /home/matt/.gvfs fuse.gvfs-fuse-daemon rw,nosuid,nodev,user=matt 0 0

  Read the article

• Direct show video renderers suck?

  - by Daniel

  So I've been looking into the world of media playback for windows and I've started making a C# Media Player using DirectShow. I started off using the VRM-7 windowed video renderer and it was brilliant except it had a couple of small problems (multi monitors, fullscreen). But after some research I found that it's deprecated and I should be using VRM9. So I changed it to use VRM9 windowless then found out that was an old post rofl _< so finally I'm using Vista/Win7 (or XP .net 3) Enhanced Video Renderer (EVR) which is apparently the most up to date Microsoft video renderer and has all the flashy performance/quality things added to it. (tbh I haven't noticed any difference but maybe I need a blue-ray or HQ video to notice it). With using EVR everything is working fine except resizing the video. Its really laggy/choppy/teary and problem something to do with its frame queueing mechanism. To demonstrate my problem open up windows media player classic. View - Options - Playback - output Chose the "EVR" DirectShow Video renderer Now restart wmp class and play a video, while it's playing click and drag a corner to resize it. You'll notice its horribly laggy. This is the exact same problem i am having. But if you chose "EVR Custom Pres. *" or EVR Sync *" resizing works beautifully! So i tried googling around for anything about EVR resizing issues and how to fix it but i couldn't believe how little i could find. I'm guessing "Custom Pres." stands for "Custom Presenter" which sounds like they made their own. Also you'll notice on the right hand size when you swap between EVR and the other EVR's the Resizer drop down on the right greys out. So basically I wan't to know how I can fix this retarded resizing problem and is there any decent documentation out there? There is a fair bit for VMR7/9 but not much for EVR. I downloaded the DirectX SDK which apparently has samples but it was a waste of 500mb of bandwidth as it had nothing relevant. Perhaps there is some way to force it not queueing up frames if that is the problem? If you want code say the word and I'll paste some in. But it's really quite simple and nothing much happens, i'm convinced it's a problem with the EVR renderer. EDIT: Oh and one other thing, what does VLC use? If you go into vlc options and change the renderer to anything but default, they all suck. So is it using VMR7? Or its own?

  Read the article

< Previous Page | 169 170 171 172 173 174 175 176 177 178 179 180  | Next Page >