Search Results

Search found 5670 results on 227 pages for 'zend router'.

Page 175/227 | < Previous Page | 171 172 173 174 175 176 177 178 179 180 181 182  | Next Page >

• Gre Tunnel Cisco Linux traffic forwarding

  - by mezgani

  I setup a gre tunnel a cisco router and a Linux machine, the tunnel interface in the Linux box named pic. Well i have to forward traffic coming from cisco through the Linux box. the rules i've set in the Linux box is described as follow: echo "1" /proc/sys/net/ipv4/ip_forward iptables -A INPUT -p 47 -j ACCEPT iptables -A FORWARD -i ppp0 -j ACCEPT iptables -A FORWARD -i pic -o ppp0 -m state --state ESTABLISHED,RELATED -j ACCEPT iptables -A FORWARD -i ppp0 -o pic -m state --state ESTABLISHED,RELATED -j ACCEPT iptables -A FORWARD -m state --state ESTABLISHED,RELATED -j ACCEPT iptables -t nat -A POSTROUTING -o ppp0 -j MASQUERADE I see the traffic coming from tunnel and forwarded to internet but no reply from sent packet. May i miss something like a routing rule.

  Read the article

• SMTP Server Times Out for 1 of 2 ISPs

  - by Jonathan Sampson

  For months I've been using a 5g sprint card for my laptop to check email. I have gmail, and three other accounts all configured in Thunderbird. Recently, I got AT&T internet service at my house and I discovered that I cannot send email when connected to my home service. I can receive just fine, but I can't send. If I plugin my 5g card, I can sent/receive with no problems. At home I'm connected wirelessly through a router. What could be causing this interruption? I even tried pinging my smtp server only to see it timeout when connected via AT&T. If more details are needed, I'll be happy to share.

  Read the article

• QoS - split bandwidth across all IPs during high load

  - by Matthew Iselin

  We have a Linux-based router which is currently working fairly well, but our network only has a 1.5 mbps incoming connection. The network is small, but during high load periods some systems can end up dominating the bandwidth. For example, a client downloading a file can easily saturate the connection leaving everyone else with barely any access to the outside world. Naturally, I'd like to fix this. I believe a combination of iptables rules and tc is in order, but I have no idea how to go about distributing the bandwidth evenly across the clients. It would be nice if there was a way to divide the bandwidth only across clients that are actually utilising the connection as well, rather than hard limit each connection to (bandwidth / number of clients).

  Read the article

• Excel 2003 opening files on network

  - by Luke

  The network is laid out with an XP Pro computer as the server hosting files, then 3 XP computers connecting to it for filesharing, all on it's own router. One computer can open .xls files no problem, and she runs Office XP. The other two computers run Office 2003, and cannot open any shared files by double-clicking them, or by selecting File-Open in Excel. If the file gets copied to the local computer, it opens instantly. I have tried disabling the AV on all computers, disabling the Windows firewall, and doublechecking permissions on the server. I have also tried disabling DDE, but that doesn't help at all, just like Tools-Options-unticking Ignore other applications. Any ideas? This apparently started a couple days ago

  Read the article

• Using ethernet cables?

  - by Farhad Yusufali

  I have an HDTV which supports internet connectivity through an ethernet port or wirelessly (but this requires an additional wireless USB adapter, which I don't have). I also have a blue ray player than supports internet connectivity through an ethernet port or wirelessly (natively - no other devices are needed). I want to connect my TV to the internet but my router is too far away. My blueray player however is already connected wirelessly. If I connected my TV to my Blueray player via ethernet, would my TV be able to connect to the internet? To clarify: Wireless Signal - Blue Ray Player - Ethernet Cable - TV Would this work?

  Read the article

• setup Mac Book Wifi interface as Wifi hotspot using specific DHCP option

  - by srjohnhuang

  I want to using my Mac Book as an access point. Besides that I also need to configure its DHCP server to not provide DNS info. For example, Mac Books AP's ssid is "MacBookHotspot". While my iPhone connected to "MacBookHotspot", I want the Wifi info displayed my iPhone would be looked like: IP ADDRESS DHCP(tab) IP Address 192.168.0.1 Subnet Mask 255.255.255.0 Router 192.168.0.254 DNS Search Domains Client ID (key point: DNS filed is blank) Does anyone have any good suggestion? Thanks!

  Read the article

• Cable Internet connectivity Problem?

  - by LightHeaded

  I just got Internet cable from Time Warner/ EarthLink. For some reason I tried everything that Time Warner and Earthlink techs told me to do but nothing seems to work. I still can't connect to the Internet. For some reason they think it's the IPv4 address since it begins with 169. I did everything the told me to 8 times, but they both give me the run around tell me it's the other's fault. How can I fix this once and for all? I have no router. I use cable to connect to the Internet. Windows Vista Cable broadband.

  Read the article

• deploy LAMP config to new boxes with low/no effort

  - by user1444233

  I'm spending a lot of time setting up new Centos 6 instances. I use a VCS (Subversion) for most of the config files and all of the webapp source files (Github), but even with excellent package managers (like yum, npm, easy_install, etc.) it still takes time. I'd like to get to the point where I could try out a new potential web host by just signing up for an account, logging in and automatically sucking my standardised config onto the box. I know there are a set of tools that can help: Puppet Chef Vagrant and a set of services that sell solutions: [Jumpbox] http://www.jumpbox.com/ [BitNami Cloud] http://bitnami.org/cloud I don't mind investing time in learning a new tool, but as a no-budget start-up, I'm keen to keep monthly costs down. My biggest concern is that time spent on the server config is time away from the codebase, and that's where I think my team and I should be investing our energy, at least until we get funded and scale up a bit. I'd be grateful of some recommendations for which way to jump on config: stick with SSH and manual deploys, at least until you get big. bite the bullet and learn [say] puppet. You may only use it 8-10 times, but it pays to have such an easy tunable server bootstrap. don't bother, just pay the $100/month for a standard config service. It'll cost you $1000/year, but you should focus on the code. Other questions in this domain I use quite a complex stack (Drupal, Zend Server, MySQL, PHP, MongoDB, Python, django), but are there standard(ish) setups that include these or that I could build upon more quickly? Are the configs optimised for small, medium, large VPS (1GB, 4GB, 16GB)? How secure are they?

  Read the article

• Why are they putting "processors" on hard drives?

  - by Celeritas

  What does it mean when they have a processor on the hard drive, how does it work, and what benfit does it have? I don't understand - the CPU is the processor and the hard drive transfers it's contents to RAM. Do have additional processors, preprocess the data some how? Here's some examples Western Digital WD Black WD1002FAEX 1TB "Dual processor speed" NETGEAR ReadyNAS 312 2-Bay Diskless Network Attached Storage "Dual-core Intel 2.1GHz processor and 2GB on-board memory" and routers now have processors too, why's that nescecary? I guess it sort of makes sense - some logic needs to happen for the packets to be read in to know which ports to send them out on, but why did old routers not need them? Example or wireless router with processor: "Dual-core processor"

  Read the article

• Always a path to the internet even in Windows SBS is off

  - by Mark

  Hello all, is it possible to have a configuration in a Windows 2003 SBS environment where in the event that the SBS box crashed/turned off/ or is being worked on that there can still exist a path to the internet for domain users and visitors to still use? I would like to have the standalone router issue DHCP IPs. The primary DNS would point to the SBS, the secondary wouuld point to the ISP DNS Server. My theory was that if someone was using the internet and the SBS box went down they wouldn't be able to access the network shares but still be able to use the internet. (We are moving everything into the clouds with Google Apps Non-Profit) Does this seem like a reasonable configuration? Or are they're pitfalls that I will fall into? Thanks Mark

  Read the article

• RRAS server 2003 one nic vpn encrypted

  - by Daniel Woodhead

  Hi All, I have a a machine installed with Server 2003 standard on it. It is behind a standard adsl router. I have setup RRAS access on it with under the custom setting and selected just vpn as the machine only has one nic installed. I can connect to the server and it all works fine. I'm just wondering where the settings are to say that it is data encrypted. I know in xp when setting up a vpn you can check the option to encrypt the data, but doing this in server 2003 there isn't the option so thought i would try and use rras. The main reason that i want to do this is that xp only allows one connection at a time. Dan

  Read the article

• Windows 7 port Forwarding Issue

  - by Elliot

  I can't get port forwarding to work now that I am using windows 7 (64-bit). I am using a wireless connection (no wired connection available). I have the ports forwarded (IP has been double checked, router settings are confirmed), there is an exception for all of the programs in question in windows firewall, and in the resource monitor windows lists the ports as available, not restricted, and yet when I either use a specific program (ie utorrent, DC++, Command & Conquer 3) or check using firefox, the port reads as closed. How do I get the port forwarding to work?

  Read the article

• One external IP 2 servers

  - by Stanley

  Currently there is one external IP pointing to a Window Web Server. Now wish to add a Linux web server. Wish to know if the following setup is ok : 119.xxx.xxx.xxx points to Window Web Server 119.xxx.xxx.xxx/Linux_Server points to the new additional Linux Server. If the above scheme is ok, then how should it be done. (In terms of where the router should be placed and configured etc). If the above scheme is unusual or not workable please suggest best practice scheme. Hope somebody knowledgable could help ...

  Read the article

• Can't access internet using a domain joined computer outside the domain environment

  - by Mike Walsh

  We had an unused box at work so took it home. It had been joined to the domain and hasn't been unjoined. When I try to use it at home (logging in with a local admin account) I can't seem to access internet pages. It gets correct IP and gateway for the local network and correct DNS servers for the home ADSL connection. I can happily ping the home router (which doesn't have any tricky firewall settings). Can't seem to ping outside, get any DNS to resolve, or (obviously) get any web pages. Is there some problem here with this having been joined to the domain?

  Read the article

• DSL connection dropping when starting game

  - by bootoo

  New connection set up last week - have called tech support, signal fine, sending out tech guy tomorrow - however i cant make sense of this using Vista, 2wire connection 6mb ATT conn, wireless, i can browse website, stream video from my PC wirelessly to my xbox, watch Hulu in high res, connection seems fine I load up World of Warcraft, i select Enter World and without fail my 2wire modem 'DSL' light goes red, my internet light goes out, im no longer connected, then after 10 or 15 seconds it works again, but game has kicked me Noticed the same thing on opening or closing Utorrent as well No other phones/devices plugged into the phone jacks in the apartment - why would joining a game cause my DSL to drop? i can only guess it throws a bunch of information to the server when i hit 'enter world' and that causes an issue that shuts my connection down or my router hates me - all help appreciated

  Read the article

• Thinking of Powerline adapters for networking

  - by Henderson McCoy

  will powerline work as good as wifi I am now in a large house (renting a room) and the router is in the front of the house and I am in the back. Don't know if wifi will have the range and stability so I am looking at all the alternatives from running a long cable to powerline. looks like a powerline adapter set will cost about $50 http://www.bestbuy.com/site/Actiontec---500-Mbps-Powerline-Home-Theater-Network-Adapter-Kit/5215483.p?id=1218625358741&skuId=5215483 has anyone use these or other powerline adapters? how is powerlines speed? Are they more stable then wifi? powerline cost is good i am just currious about the performance

  Read the article

• Public IP Routing over Private GRE tunnel

  - by Paul

  I have a GRE tunnel configured between two linux boxes. The tunnel works fine. I can ping from each host the other private ip. Head privateip: 10.0.0.1 publicip: 8.8.8.8 Tail privateip: 10.0.0.2 publicip: 7.7.7.7 The public IP on Tail has the network block 9.9.9.0/23 statically routed over the 7.7.7.7 interface. The idea is to make the 9.9.9.0/23 ips work on servers on the 8.8.8.8 network. I configure the tail host to route the /23 block. I mounted a 9.9 IP on the head server. I can ping the 9.9 ip from the tail to the head. I can't ping the 9.9 ip from the public internet. I think I need to add some other routes because of gateway issues, but I can't seem to wrap my mind around it (not a router guy, just beating my way through something that I have never done before and vaguely understand) --danks

  Read the article

• Why do the IP addresses randomly change?

  - by GiddyUpHorsey

  I have a network with the following: Cable modem with static IP address Router Desktop - Win 7 VM Host - VMware ESXi 4.0 A couple of VM Guests - Windows Every now and then my Win 7 PC is unable to access some of the VMs. When I ping the VMs by their domain name their IP address shows up as the IP address of the cable modem. Sometimes I can fix it by running ipconfig /flushdns. The IP address will reset back to what it was supposed to be, but occasionally it wont work. Why does this happen and how can I fix it?

  Read the article

• FTP timeout only the first time

  - by user1474681

  I'm using PureFTPd on MacOSX (Snow Leopard, not server version). When trying to access the FTP account from the outside via dyndns (e.g. using https://www.wormly.com/test_ftp_server) the connection always times out the FIRST time. When I try AGAIN in the next few seconds it works. What is this about? I have forwarded the ports to my apple router and tried disabling the OSX firewall as well. Thanks for any advice. Dennis

  Read the article

• IIS 7 URL rewrite rule

  - by Andrew

  Hello, guys! We have here to web servers behind a router - one IIS and one Tomcat (on different machines / IP addresses). The domain is pointing to out external IP, which is forwarded to IIS (internal IP 192.168.1.10 for example). I'm trying to do the following: when [www.]ourdomain.com is entered the default web site on IIS have to be loaded (this part is ok), but when test.ourdomain.com is entered I want to redirect this request to another web server (192.168.1.11 for example). I created a site "test" on IIS and it is displayed when test.ourdomain.com is entered. Then I tried to redirect it with following rule: Requested URL matches the pattern: * (using wildcards) Condition: {HTTP_HOST} matches test.ourdomain.com Action type: Rewrite Rewrite URL: http://192.168.1.11/{R:0} but when I try to load test.ourdomain.com now I get IIS's error 404 page. Obviously I'm wrong :-) How can I do such a redirect?

  Read the article

• Mac OS X: network disabled because security breach

  - by fireeyedboy

  Dear all, I just recieved a message on my Mac OS X system telling me (loosely translated from Dutch): "The network has been temporarily disabled because the network's security was breached." (It's a wireless WPA2-PSK secured network BTW) I looked in the logs of my router (a Zyxel P-2602HW-D1A) only to see a few (outbound) "syn flood TCP ATTACK" logs, but those were from like a week ago, other than that nothing. What tools on Mac OS X do I have to analyse this security breach occurence? Are there some security logs on Mac OS X that I can inspect? What other measurements should I take? And how serious should I take this warning from Mac OS X? System: Macbook Pro Intel Core 2 Duo 2.2 Ghz OS: Mac OS X 10.5.8 Network: wireless WPA2-PSK Relevant software: Parallels Desktop with Windows XP (was open, but stopped at the time) Other systems on my network: Windows XP SP3 desktop (was running at the time) If you need any more info, don't hestitate to ask. Thanks in advance.

  Read the article

• How to access internet from 2 laptops with data card plugged-in in one of the machine?

  - by learnerforever

  Hi, I have 2 laptops - one running Windows XP and other running Vista. Both have wifi card.I have one Reliance broadband data card. I want to be able to access internet on both the machines simultaneously using this one data card. Please help. I think, there would be many many ways to do it. I do have some linksys router but any simple quick way without any extra hardware? like we could set up p2p or WLAN between these 2 machines, because both have wifi card so we shouldn't compulsorily need any extra hardware(?) I am fine with connecting data card to either of the machines. Thanks,

  Read the article

• How to access internet from 2 laptops with data card plugged-in in one of the machine?

  - by learnerforever

  Hi, I have 2 laptops - one running Windows XP and other running Vista. Both have wifi card.I have one Reliance broadband data card. I want to be able to access internet on both the machines simultaneously using this one data card. Please help. I think, there would be many many ways to do it. I do have some linksys router but any simple quick way without any extra hardware? like we could set up p2p or WLAN between these 2 machines, because both have wifi card so we shouldn't compulsorily need any extra hardware(?) I am fine with connecting data card to either of the machines. Thanks,

  Read the article

• Securing data sent to an unencrypted WiFi AP

  - by David Parunakian

  The business plan of a project I'm involved in assumes selling certain WiFi-enabled devices to end users. All these devices originally have an unencrypted connection and a standard SSID. The problem is that although the user can connect to it and set both a new SSID and a WPA passphrase, these are being sent to the AP in plain text and thus can be intercepted by anyone nearby with a sniffer. What's the best solution to this problem, and why? Initially set up an encrypted wireless network at the device and supply the user with a printed passphrase Buy an SSL certificate for the AP's default IP address or local domain name (the APs aren't supposed to work as a router and have a captive portal & dnsmasq installed, so all of them can pretend to be myunit.example.com, as far as I understand) Something different Thank you.

  Read the article

• Confirm disk is broken when it passes all diagnostics

  - by Halfgaar

  I have a system with a potentially broken disk, but the disk passes all manner of diagnostics. I have been unable to confirm that the disk is broken. What are my options? I could just replace the disk, but because this situation is very similar to another more severe situation I have (long story), I'd like to actually make a proper diagnosis as opposed to randomly binning hardware. The issue and history is this: I had a Debian Linux PC (500 MHz P3) acting as router, nagios and munin. It crashed every couple of weeks. No logs or dmesg could be obtained (because it's an old Compaq that only boots when you configure it as keyboardless, making connecting a keyboard later, once it's booted, impossible). At the time, I just replaced the computer with another Compaq (P4 2.4 GHz) because I thought the hardware was faulty. However, it still crashed every couple of weeks. the difference is that on this computer, I can still SSH into it. It gives all kinds of errors on hda. I'd like to confirm that the disk is broken, but nothing I do confirms this: SMART error logs shows no errors. Normally when a disk starts acting up, SMART my pass, but it still records a read-error in the error log. SMART self-test (smartctl -t long /dev/sda) completes without errors. re-allocated sector count (a tell-tale parameter) has been 31 all its life, even when the disk was still in use in my desktop PC years ago, and it still is. The figure never changed. dd if=/dev/sda of=/dev/null bs=4096 passes with flying colors. What else can I do to assess the health of the drive? Again, this is not about making this router fully functional again, this is a disk forensic question, because it just so happens that I have another server that potentially has the same problem, and knowing the answer to this will possibly help me greatly. For the record, below are logs and such. This is the smartctl -a output: smartctl 5.40 2010-07-12 r3124 [i686-pc-linux-gnu] (local build) Copyright (C) 2002-10 by Bruce Allen, http://smartmontools.sourceforge.net === START OF INFORMATION SECTION === Model Family: Seagate Barracuda 7200.7 and 7200.7 Plus family Device Model: ST3120026A Serial Number: 5JT1CLQM Firmware Version: 3.06 User Capacity: 120,034,123,776 bytes Device is: In smartctl database [for details use: -P show] ATA Version is: 6 ATA Standard is: ATA/ATAPI-6 T13 1410D revision 2 Local Time is: Mon Jul 1 21:18:33 2013 CEST SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 24) The self-test routine was aborted by the host. Total time to complete Offline data collection: ( 430) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. No General Purpose Logging support. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 85) minutes. SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x000f 050 046 006 Pre-fail Always - 47766662 3 Spin_Up_Time 0x0003 097 096 000 Pre-fail Always - 0 4 Start_Stop_Count 0x0032 100 100 020 Old_age Always - 10 5 Reallocated_Sector_Ct 0x0033 100 100 036 Pre-fail Always - 31 7 Seek_Error_Rate 0x000f 084 060 030 Pre-fail Always - 820305 9 Power_On_Hours 0x0032 048 048 000 Old_age Always - 46373 10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0 12 Power_Cycle_Count 0x0032 100 100 020 Old_age Always - 605 194 Temperature_Celsius 0x0022 036 065 000 Old_age Always - 36 195 Hardware_ECC_Recovered 0x001a 050 046 000 Old_age Always - 47766662 197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 0 198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline - 0 199 UDMA_CRC_Error_Count 0x003e 200 196 000 Old_age Always - 6 200 Multi_Zone_Error_Rate 0x0000 100 253 000 Old_age Offline - 0 202 Data_Address_Mark_Errs 0x0032 100 253 000 Old_age Always - 0 SMART Error Log Version: 1 No Errors Logged SMART Self-test log structure revision number 1 Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Extended offline Aborted by host 80% 46361 - # 2 Extended offline Completed without error 00% 46358 - # 3 Short offline Completed without error 00% 12046 - # 4 Extended offline Completed without error 00% 10472 - # 5 Short offline Completed without error 00% 10471 - # 6 Short offline Completed without error 00% 10471 - # 7 Short offline Completed without error 00% 6770 - # 8 Extended offline Aborted by host 90% 5958 - # 9 Extended offline Aborted by host 90% 5951 - #10 Short offline Completed without error 00% 5024 - #11 Extended offline Aborted by host 80% 5024 - #12 Short offline Completed without error 00% 3697 - #13 Short offline Completed without error 00% 237 - #14 Short offline Completed without error 00% 145 - #15 Short offline Completed without error 00% 69 - #16 Extended offline Completed without error 00% 68 - #17 Short offline Completed without error 00% 66 - #18 Short offline Completed without error 00% 49 - #19 Short offline Completed without error 00% 29 - #20 Short offline Completed without error 00% 29 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. And this is the dmesg error when it has crashed (which repeats for a bunch of different sectors): [1755091.211136] sd 0:0:0:0: [sda] Unhandled error code [1755091.211144] sd 0:0:0:0: [sda] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK [1755091.211151] sd 0:0:0:0: [sda] CDB: Read(10): 28 00 08 fe ad 38 00 00 08 00 [1755091.211166] end_request: I/O error, dev sda, sector 150908216

  Read the article

< Previous Page | 171 172 173 174 175 176 177 178 179 180 181 182  | Next Page >