Search Results

Search found 41561 results on 1663 pages for 'linux command'.

Page 176/1663 | < Previous Page | 172 173 174 175 176 177 178 179 180 181 182 183  | Next Page >

  • It is okay to set MASQUERADE at 2 network interfaces in a Linux server?

    - by Patrick L
    There is a Linux server with 3 network interfaces, eth0, eth1, eth2. IP forwarding has been turn on in this server. eth0 is connected to 10.0.1.0/24. Its IP is 10.0.1.1. eth1 is connected to 172.16.1.0/24. Its IP is 172.16.1.1. Server A can ping router C at 172.16.1.2. eth2 is connected to 192.168.1.0/24. Its IP is 192.168.1.1. Server A can ping server B at 192.168.1.2. Router C is able to route to 172.16.2.0/24 and 172.16.3.0/24. [10.0.1.0/24] | 172.16.2.0/24------| | [C]------172.16.1.0/24------[A]------192.168.1.0/24------[B] 172.16.3.0/24------| We have set MASQUERADE at eth0. When server B (192.168.1.2) connect to 10.0.1.0/24, IP MASQUERADE will happen at eth0. Can we set MASQUERADE at eth1? Is it okay to set MASQUERADE at more than 1 network interfaces in Linux?

    Read the article

  • My linux server takes more than an hour to boot. Suggestions?

    - by jamieb
    I am building a CentOS 5.4 system that boots off a compact flash card using a card reader that emulates an IDE drive. It literally takes about an hour to boot. The ultra-slow part occurs when Grub is loading the kernel. Once that's done, the rest of the boot process only takes about a minute to get to a login prompt. Does anyone have any suggestions? I suspect that it may have to do with UDMA. Everything IDE-related in my BIOS seems to checkout. The read performance hdparm is telling me 1.77 MB/s. Ouch! (But even at that rate, it still shouldn't take an hour to decompress and load the kernel) [root@server ~]# hdparm -tT /dev/hdc /dev/hdc: Timing cached reads: 2444 MB in 2.00 seconds = 1222.04 MB/sec Timing buffered disk reads: 6 MB in 3.39 seconds = 1.77 MB/sec Trying to enable DMA is a no-go though: [root@server ~]# hdparm -d1 /dev/hdc /dev/hdc: setting using_dma to 1 (on) HDIO_SET_DMA failed: Operation not permitted using_dma = 0 (off) Here's some command outputs that might help: System [root@server ~]# uname -a Linux server.localdomain 2.6.18-164.el5xen #1 SMP Thu Sep 3 04:47:32 EDT 2009 i686 i686 i386 GNU/Linux PCI info: [root@server ~]# lspci -v 00:00.0 Host bridge: Intel Corporation 82945G/GZ/P/PL Memory Controller Hub (rev 02) Subsystem: Intel Corporation 82945G/GZ/P/PL Memory Controller Hub Flags: bus master, fast devsel, latency 0 Capabilities: [e0] Vendor Specific Information 00:02.0 VGA compatible controller: Intel Corporation 82945G/GZ Integrated Graphics Controller (rev 02) (prog-if 00 [VGA controller]) Subsystem: Intel Corporation 82945G/GZ Integrated Graphics Controller Flags: bus master, fast devsel, latency 0, IRQ 10 Memory at fdf00000 (32-bit, non-prefetchable) [size=512K] I/O ports at ff00 [size=8] Memory at d0000000 (32-bit, prefetchable) [size=256M] Memory at fdf80000 (32-bit, non-prefetchable) [size=256K] Capabilities: [90] Message Signalled Interrupts: 64bit- Queue=0/0 Enable- Capabilities: [d0] Power Management version 2 00:1d.0 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #1 (rev 01) (prog-if 00 [UHCI]) Subsystem: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #1 Flags: bus master, medium devsel, latency 0, IRQ 16 I/O ports at fe00 [size=32] 00:1d.1 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #2 (rev 01) (prog-if 00 [UHCI]) Subsystem: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #2 Flags: bus master, medium devsel, latency 0, IRQ 17 I/O ports at fd00 [size=32] 00:1d.2 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #3 (rev 01) (prog-if 00 [UHCI]) Subsystem: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #3 Flags: bus master, medium devsel, latency 0, IRQ 18 I/O ports at fc00 [size=32] 00:1d.3 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #4 (rev 01) (prog-if 00 [UHCI]) Subsystem: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #4 Flags: bus master, medium devsel, latency 0, IRQ 19 I/O ports at fb00 [size=32] 00:1d.7 USB Controller: Intel Corporation 82801G (ICH7 Family) USB2 EHCI Controller (rev 01) (prog-if 20 [EHCI]) Subsystem: Intel Corporation 82801G (ICH7 Family) USB2 EHCI Controller Flags: bus master, medium devsel, latency 0, IRQ 16 Memory at fdfff000 (32-bit, non-prefetchable) [size=1K] Capabilities: [50] Power Management version 2 Capabilities: [58] Debug port 00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev e1) (prog-if 01 [Subtractive decode]) Flags: bus master, fast devsel, latency 0 Bus: primary=00, secondary=01, subordinate=01, sec-latency=32 I/O behind bridge: 0000d000-0000dfff Memory behind bridge: fde00000-fdefffff Prefetchable memory behind bridge: 00000000fdd00000-00000000fdd00000 Capabilities: [50] #0d [0000] 00:1f.0 ISA bridge: Intel Corporation 82801GB/GR (ICH7 Family) LPC Interface Bridge (rev 01) Subsystem: Intel Corporation 82801GB/GR (ICH7 Family) LPC Interface Bridge Flags: bus master, medium devsel, latency 0 Capabilities: [e0] Vendor Specific Information 00:1f.2 IDE interface: Intel Corporation 82801GB/GR/GH (ICH7 Family) SATA IDE Controller (rev 01) (prog-if 80 [Master]) Subsystem: Intel Corporation 82801GB/GR/GH (ICH7 Family) SATA IDE Controller Flags: bus master, 66MHz, medium devsel, latency 0, IRQ 17 I/O ports at <unassigned> I/O ports at <unassigned> I/O ports at <unassigned> I/O ports at <unassigned> I/O ports at f800 [size=16] Capabilities: [70] Power Management version 2 00:1f.3 SMBus: Intel Corporation 82801G (ICH7 Family) SMBus Controller (rev 01) Subsystem: Intel Corporation 82801G (ICH7 Family) SMBus Controller Flags: medium devsel, IRQ 17 I/O ports at 0500 [size=32] 01:04.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10) Subsystem: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ Flags: bus master, medium devsel, latency 32, IRQ 18 I/O ports at de00 [size=256] Memory at fdeff000 (32-bit, non-prefetchable) [size=256] Capabilities: [50] Power Management version 2 01:06.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10) Subsystem: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ Flags: bus master, medium devsel, latency 32, IRQ 17 I/O ports at dc00 [size=256] Memory at fdefe000 (32-bit, non-prefetchable) [size=256] Capabilities: [50] Power Management version 2 01:07.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10) Subsystem: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ Flags: bus master, medium devsel, latency 32, IRQ 19 I/O ports at da00 [size=256] Memory at fdefd000 (32-bit, non-prefetchable) [size=256] Capabilities: [50] Power Management version 2 hdparm ouput: [root@server ~]# hdparm /dev/hdc /dev/hdc: multcount = 0 (off) IO_support = 0 (default 16-bit) unmaskirq = 0 (off) using_dma = 0 (off) keepsettings = 0 (off) readonly = 0 (off) readahead = 256 (on) geometry = 8146/16/63, sectors = 8211168, start = 0 [root@server ~]# hdparm -I /dev/hdc /dev/hdc: ATA device, with non-removable media Model Number: InnoDisk Corp. - iCF4000 4GB Serial Number: 20091023AACA70000753 Firmware Revision: 081107 Standards: Supported: 5 Likely used: 6 Configuration: Logical max current cylinders 8146 8146 heads 16 16 sectors/track 63 63 -- CHS current addressable sectors: 8211168 LBA user addressable sectors: 8211168 device size with M = 1024*1024: 4009 MBytes device size with M = 1000*1000: 4204 MBytes (4 GB) Capabilities: LBA, IORDY(can be disabled) Standby timer values: spec'd by Vendor R/W multiple sector transfer: Max = 2 Current = 2 DMA: mdma0 mdma1 mdma2 udma0 udma1 *udma2 udma3 udma4 Cycle time: min=120ns recommended=120ns PIO: pio0 pio1 pio2 pio3 pio4 Cycle time: no flow control=120ns IORDY flow control=120ns Commands/features: Enabled Supported: * Power Management feature set * WRITE_BUFFER command * READ_BUFFER command * NOP cmd * CFA feature set * Mandatory FLUSH_CACHE HW reset results: CBLID- above Vih Device num = 0 CFA power mode 1: enabled and required by some commands Maximum current = 100ma Checksum: correct

    Read the article

  • Linux server apache httpd processes take i/o wait to close to 100% and lock down server

    - by user3682065
    For about 5 days now, and seemingly out of the blue, my linux server has started locking up from time to time. The pattern is always the same as far as I can tell from top and iotop commands around the time it starts happening: One or more httpd processes (usually one) hang and start using up 100% of CPU power, the %wa goes close to 100% and in the iotop I see several httpd processes with 99.99% in the IO column. I'm also running an SVN server on this machine through apache and the one way that I've been consistently able to reproduce this is to do an SVN commit of new files or an SVN update from the repository on this server (I am the only one using this SVN repository). This will always reproduce this scenario successfully, but until very recently I had no problems at all checking in/out of SVN. But sometimes it just happens for no detectable reason at all it seems. So it seems like there is some issue with my Apache that leads it to have processes use up a lot of read/write upon certain triggers. I was wondering if anyone could help me uncover that issue. EDIT: OK now it's happening again: This is top: [root@server ~]# top top - 10:56:54 up 2:59, 5 users, load average: 171.46, 70.35, 27.01 Tasks: 328 total, 2 running, 326 sleeping, 0 stopped, 0 zombie Cpu(s): 1.9%us, 2.0%sy, 0.0%ni, 0.0%id, 96.1%wa, 0.0%hi, 0.0%si, 0.0%st Mem: 2021144k total, 1968192k used, 52952k free, 2500k buffers Swap: 4194288k total, 2938584k used, 1255704k free, 39008k cached PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND 10390 apache 20 0 2774m 936m 6200 D 2.0 47.4 1:52.27 httpd 2149 root 20 0 927m 13m 1040 S 0.7 0.7 1:50.46 namecoind 11 root 20 0 0 0 0 R 0.3 0.0 0:30.10 events/0 23 root 20 0 0 0 0 S 0.3 0.0 0:17.88 kblockd/1 2049 root 20 0 382m 4932 2880 D 0.3 0.2 0:03.67 httpd 2144 root 20 0 1702m 69m 1164 S 0.3 3.5 5:19.68 bitcoind 6325 root 20 0 15164 1100 656 R 0.3 0.1 0:11.09 top 10311 apache 20 0 387m 9496 7320 D 0.3 0.5 0:01.89 httpd 10313 apache 20 0 391m 10m 7364 D 0.3 0.5 0:02.40 httpd 10466 apache 20 0 399m 12m 7392 D 0.3 0.7 0:02.41 httpd 10599 apache 20 0 391m 9324 7340 D 0.3 0.5 0:00.15 httpd 10628 apache 20 0 384m 7620 4052 D 0.3 0.4 0:00.01 httpd 10633 apache 20 0 384m 7048 3504 D 0.3 0.3 0:00.01 httpd 10634 apache 20 0 384m 8012 4048 D 0.3 0.4 0:00.02 httpd 10638 apache 20 0 400m 22m 9.8m D 0.3 1.1 0:01.93 httpd 10640 apache 20 0 385m 8288 4028 D 0.3 0.4 0:00.03 httpd 10641 apache 20 0 401m 21m 6376 D 0.3 1.1 0:01.45 httpd 10759 apache 20 0 385m 8816 3480 D 0.3 0.4 0:01.45 httpd 10773 apache 20 0 384m 8044 3464 D 0.3 0.4 0:00.02 httpd This is an iotop snapshot: Total DISK READ: 5.93 M/s | Total DISK WRITE: 0.00 B/s TID PRIO USER DISK READ DISK WRITE SWAPIN IO> COMMAND 10732 be/4 apache 3.76 K/s 0.00 B/s 0.00 % 58.48 % httpd 876 be/3 root 0.00 B/s 52.68 K/s 0.00 % 52.98 % [jbd2/dm-1-8] 10906 be/4 root 124.17 K/s 0.00 B/s 0.00 % 23.03 % sh -c [ -x /usr/local/psa/admin/sbin/backupmng ] && /usr/local/psa/admin/sbin/backupmng >/dev/null 2>&1 2156 be/4 root 206.94 K/s 0.00 B/s 0.00 % 21.15 % bitcoind 10904 be/4 mysql 0.00 B/s 0.00 B/s 0.00 % 18.94 % mysqld --basedir=/usr --datadir=/var/lib/mysql --user=mysql --log-error=/var/log/mysqld.log --pid-file=/var/run/mysqld/mysqld.pid --socket=/var/lib/mysql/mysql.sock 10773 be/4 apache 7.53 K/s 0.00 B/s 0.00 % 14.77 % httpd 10641 be/4 apache 15.05 K/s 0.00 B/s 0.00 % 11.57 % httpd 10399 be/4 apache 1057.29 K/s 0.00 B/s 43.16 % 10.56 % httpd 10682 be/4 sw-cp-se 158.03 K/s 0.00 B/s 0.00 % 7.45 % sw-engine-cgi -c /usr/local/psa/admin/conf/php.ini -d auto_prepend_file=auth.php3 -u psaadm 10774 be/4 apache 3.76 K/s 0.00 B/s 0.00 % 6.53 % httpd 10624 be/4 apache 0.00 B/s 0.00 B/s 0.00 % 5.53 % httpd 10356 be/4 apache 899.26 K/s 0.00 B/s 35.52 % 4.01 % httpd 10795 be/4 apache 0.00 B/s 0.00 B/s 0.00 % 3.93 % httpd 10804 be/4 apache 7.53 K/s 0.00 B/s 0.00 % 3.08 % httpd 4379 be/4 root 2.89 M/s 0.00 B/s 99.99 % 0.00 % namecoind 10619 be/4 apache 462.80 K/s 0.00 B/s 7.80 % 0.00 % httpd 10636 be/4 apache 3.76 K/s 0.00 B/s 0.00 % 0.00 % httpd 10716 be/4 mysql 105.35 K/s 0.00 B/s 5.92 % 0.00 % mysqld --basedir=/usr --datadir=/var/lib/mysql --user=mysql --log-error=/var/log/mysqld.log --pid-file=/var/run/mysqld/mysqld.pid --socket=/var/lib/mysql/mysql.sock 1988 be/4 root 18.81 K/s 0.00 B/s 0.00 % 0.00 % spamd_full.sock I also ran lsof -p for pid 10390 which was way up top under the top command and this is the bottom line where I can sort of see what request this was and it says CLOSE_WAIT: httpd 10390 apache 34u IPv6 315879 0t0 TCP default-domain.com:https->crawl-66-249-65-91.googlebot.com:42907 (CLOSE_WAIT) I'm still not sure what exactly is causing this all to happen though? I killed that service but %wa and load average remain high, I also stopped mysqld and other services. It really only goes down once I stop httpd altogether, and even then I can't start it without finding remaining hanging httpd processes via "netstat -tulpn", killing those or doing "killall -9 httpd" and after waiting a while for it to cycle through all those then doing /etc/init.d/httpd start

    Read the article

  • How to send AT command in android?

    - by jitendra Kumar
    Hi All, I want to send At command throug my application to modem. Can some one please let me know how to send AT command thr my application?? Do we need Phone object to send AT command??? The ATResponseParser class parses part of the AT command syntax used to communicate with the mobile radio hardware in a mobile handset. This is, in fact, a command syntax very much like the AT command syntax used by modems, a standard described in the 3GPP document number TS 27.007 and related specifications. I ant to send below AT command to Mode. 6.5 Hangup call +CHUP Table 13a: +CHUP action command syntax Command Possible response(s) +CHUP +CHUP=? Please help me. Regards, Jitendra Kumar

    Read the article

  • Get a return value from a screen'd command

    - by AndyMac
    I'm running a process in a screen (on Ubuntu 13.10, if it matters). I can execute a command within that screen with: screen -p 0 -X eval 'stuff \"$command\"\015' I'm not 100% sure what this command is doing to begin with, though it's functioning correctly. The reason behind it is I'm running a Minecraft server (still) and this screens in to the correct screen, and throws the command on the running command line. So that's good, so far. But what I'd like is to be able to run this command with a return value. So for example, if I were to run a "list" command, it'd tell me how many people and who is online, but I need to capture that output and put it somewhere. Anyone know of a way to accomplish this? I can't tell the minecraft server command line to redirect the output somewhere else since it doesn't have direct command line access, so the only way I could do this would be to grab all output of the screen while I'm connected ... but I'm not sure if that's possible.

    Read the article

  • Bricked - tty mode incorrect, terminal disabled, unity broken

    - by user989805
    After installing VirtualBox unity seems to be uninstalled.. Launcher and task bar are missing. I can't access terminal from the normal ctrl alt T command. I tried logging into TTY mode but it says my login is incorrect. I am trying to login with my normal ubuntu username and password. I have searched for solutions but since I dont have terminal or TTY I cant bash out any commands, and I have tried safeboot but the root terminal always says it cant run whatever command I enter. I am really lost and I am trying to avoid a fresh install :( I greatly and genuinely appreciate any help! This is the computer I use for college!

    Read the article

  • Modifying AD Schema permissions from the command line

    - by Ryan Roussel
    Recently while making some changes for a client, I accidently dug myself into a pretty deep hole.  I was trying to explicitly deny a certain user from reading a few group policies including the Default Domain Policy.  When I went in to make the change I accidently denied Authenticated Users rather than the AD user object.  This of course made the GPO inaccessible to all users including any with domain admin rights.  The policy could no longer be modified in the GPMC and worse, changes could not be made through ADSIedit.   The errors I was getting from inside ADSIedit when trying to edit the container looked like this This object has one or more property sheets currently open. Invalid path to object The only solution was to strip Authenticated Users from the container ACL completely in the schema, then re-add it back with the default read and apply rights.  To perform this action, I used a command I had never used before:  DSALCS.exe  It’s part of the DSMOD group of tools.  Since this command interacts with the actual schema, you have to know the full LDAP container or object name.  In this case the GUID of the Default Domain Policy: {31B2F340-016D-11D2-945F-00C04FB984F9}   The actual commands I ran looked like this:   To display the current ACL of the container: c:\>dsacls “cn={31B2F340-016D-11D2-945F-00C04FB984F9},cn=Policies,cn=System, dc=domain,dc=com” /A To strip Authenticated Users from the ACL of the container: c:\>dsacls “cn={31B2F340-016D-11D2-945F-00C04FB984F9},cn=Policies,cn=System, dc=domain,dc=com” /R “NT Authority\Authenticated Users”   For full reference of the DSACLS.EXE command visit: http://support.microsoft.com/kb/281146 Once the Authenticated Users was cleared from the ACL, I was able to use Group Policy Management Console to reassign the default permissions.

    Read the article

  • How to run Repository Creation Utility (RCU) on 64-bit Linux

    - by Kevin Smith
    I was setting up WebCenter Content (WCC) on a new virtual box running 64-bit Linux and ran into a problem when I tried to run the Repository Creation Utility (RCU). I saw this error when trying to start RCU .../rcuHome/jdk/jre/bin/java: /lib/ld-linux.so.2: bad ELF interpreter: No such file or directory I think I remember running into this before and reading something about RCU only being supported on 32-bit Linux. I decided to try and see if I could get it to run on 64-bit Linux. I saw it was using it's own copy of java (.../rcuHome/jdk/jre/bin/java), so I decided to try and get it to use the 64-bit JRockit I had already installed. I edited the rcu script in rcuHome/bin and replaced JRE_DIR=$ORACLE_HOME/jdk/jre with JRE_DIR=/apps/java/jrockit-jdk1.6.0_29-R28.2.2-4.1.0 Sure enough that fixed it. I was able to run RCU and create the WCC schema.

    Read the article

  • Need help fixing a strange path error in bash

    - by Evan
    UPDATE Ok, I found some errors in the path which I think I fixed, but now it's not running in any case - which for some reason I think is a step forward. Thanks for suggesting the following steps, here is their output: user@computer:~$ echo $PATH /usr/share/fsl/bin:/usr/local/sbin:/usr/local/bin:/usr/sbin:/usr/bin:/sbin:/bin:/usr/games:/usr/local/bin:/usr/bin:/bin:/usr/bin/X11:/usr/games:/usr/local/matlab/bin:/usr/local/VoxBo/bin:/usr/local/itt/idl64/bin:/usr/local/afni/bin/:/usr/local/mricron:/usr/lib/voxbo/bin:/home/user/folder:/usr/local/bin:/usr/bin:/bin:/usr/bin/X11/:/usr/games/:/usr/local/matlab/bin:/usr/local/VoxBo/bin/:/usr/local/itt/idl64/bin:/usr/local/afni/bin/:/usr/local/mricron/ user@computer:~$ typeset -p PATH declare -x PATH="/usr/share/fsl/bin:/usr/local/sbin:/usr/local/bin:/usr/sbin:/usr/bin:/sbin:/bin:/usr/games:/usr/local/bin:/usr/bin:/bin:/usr/bin/X11:/usr/games:/usr/local/matlab/bin:/usr/local/VoxBo/bin:/usr/local/itt/idl64/bin:/usr/local/afni/bin/:/usr/local/mricron:/usr/lib/voxbo/bin:/home/user/folder:/usr/local/bin:/usr/bin:/bin:/usr/bin/X11/:/usr/games/:/usr/local/matlab/bin:/usr/local/VoxBo/bin/:/usr/local/itt/idl64/bin:/usr/local/afni/bin/:/usr/local/mricron/" user@computer:~$ type app1 app1 is /home/user/folder/app1 user@computer:~$ type app2 app2 is /home/user/folder/app2 user@computer:~$ app1 bash: /home/user/folder/app1: No such file or directory user@computer:~$ app2 bash: /home/user/folder/app2: No such file or directory user@computer:~$ /home/user/folder/app1 bash: /home/user/folder/app1: No such file or directory user@computer:~$ /home/user/folder/app2 bash: /home/user/folder/app2: No such file or directory user@computer:~$ cd /home/user/folder user@computer:~/folder$ app1 bash: /home/user/folder/app1: No such file or directory user@computer:~/folder$ ./app1 bash: ./app1: No such file or directory user@computer:~/folder$ ./app2 bash: ./app2: No such file or directory user@computer:~/folder$ ls -l total 29384 -rwxr-xr-x 1 user user 14949776 2011-02-03 11:09 app1 -rwxr-xr-x 1 user user 15137300 2011-02-03 11:10 app2 user@computer:~/folder$ Thanks for everyone's input! ORIGINAL QUESTION I have two executable files I downloaded and am trying to add to the path. They are located in /home/user/folder and the specific files are /home/user/folder/app1 /home/user/folder/app2 Both app1 and app2 have the executable flag set to all (user, group, other). I can execute the files if I am in /home/user/folder and I execute these commands ./app1 ./app2 However I can't run them from elsewhere. I added this line to my .profile PATH="$PATH:/home/user/folder" and then sourced the path with . /home/user/.profile and I can see app1 and app2 when I use command completion (pressing tab). However here is what happens when I try to run app1 or app2 with the following commands (the following only shows 'app1' but the same is true of 'app2') user@comp:~$ app1 -bash: app1: command not found user@comp:~$ /home/user/folder/app1 -bash: app1: command not found user@comp:~/folder$ ./app1 (program runs) I'm stumped :), I must have missed something simple. Thanks for your help!!

    Read the article

  • Recover Data Like a Forensics Expert Using an Ubuntu Live CD

    - by Trevor Bekolay
    There are lots of utilities to recover deleted files, but what if you can’t boot up your computer, or the whole drive has been formatted? We’ll show you some tools that will dig deep and recover the most elusive deleted files, or even whole hard drive partitions. We’ve shown you simple ways to recover accidentally deleted files, even a simple method that can be done from an Ubuntu Live CD, but for hard disks that have been heavily corrupted, those methods aren’t going to cut it. In this article, we’ll examine four tools that can recover data from the most messed up hard drives, regardless of whether they were formatted for a Windows, Linux, or Mac computer, or even if the partition table is wiped out entirely. Note: These tools cannot recover data that has been overwritten on a hard disk. Whether a deleted file has been overwritten depends on many factors – the quicker you realize that you want to recover a file, the more likely you will be able to do so. Our setup To show these tools, we’ve set up a small 1 GB hard drive, with half of the space partitioned as ext2, a file system used in Linux, and half the space partitioned as FAT32, a file system used in older Windows systems. We stored ten random pictures on each hard drive. We then wiped the partition table from the hard drive by deleting the partitions in GParted. Is our data lost forever? Installing the tools All of the tools we’re going to use are in Ubuntu’s universe repository. To enable the repository, open Synaptic Package Manager by clicking on System in the top-left, then Administration > Synaptic Package Manager. Click on Settings > Repositories and add a check in the box labelled “Community-maintained Open Source software (universe)”. Click Close, and then in the main Synaptic Package Manager window, click the Reload button. Once the package list has reloaded, and the search index rebuilt, search for and mark for installation one or all of the following packages: testdisk, foremost, and scalpel. Testdisk includes TestDisk, which can recover lost partitions and repair boot sectors, and PhotoRec, which can recover many different types of files from tons of different file systems. Foremost, originally developed by the US Air Force Office of Special Investigations, recovers files based on their headers and other internal structures. Foremost operates on hard drives or drive image files generated by various tools. Finally, scalpel performs the same functions as foremost, but is focused on enhanced performance and lower memory usage. Scalpel may run better if you have an older machine with less RAM. Recover hard drive partitions If you can’t mount your hard drive, then its partition table might be corrupted. Before you start trying to recover your important files, it may be possible to recover one or more partitions on your drive, recovering all of your files with one step. Testdisk is the tool for the job. Start it by opening a terminal (Applications > Accessories > Terminal) and typing in: sudo testdisk If you’d like, you can create a log file, though it won’t affect how much data you recover. Once you make your choice, you’re greeted with a list of the storage media on your machine. You should be able to identify the hard drive you want to recover partitions from by its size and label. TestDisk asks you select the type of partition table to search for. In most cases (ext2/3, NTFS, FAT32, etc.) you should select Intel and press Enter. Highlight Analyse and press enter. In our case, our small hard drive has previously been formatted as NTFS. Amazingly, TestDisk finds this partition, though it is unable to recover it. It also finds the two partitions we just deleted. We are able to change their attributes, or add more partitions, but we’ll just recover them by pressing Enter. If TestDisk hasn’t found all of your partitions, you can try doing a deeper search by selecting that option with the left and right arrow keys. We only had these two partitions, so we’ll recover them by selecting Write and pressing Enter. Testdisk informs us that we will have to reboot. Note: If your Ubuntu Live CD is not persistent, then when you reboot you will have to reinstall any tools that you installed earlier. After restarting, both of our partitions are back to their original states, pictures and all. Recover files of certain types For the following examples, we deleted the 10 pictures from both partitions and then reformatted them. PhotoRec Of the three tools we’ll show, PhotoRec is the most user-friendly, despite being a console-based utility. To start recovering files, open a terminal (Applications > Accessories > Terminal) and type in: sudo photorec To begin, you are asked to select a storage device to search. You should be able to identify the right device by its size and label. Select the right device, and then hit Enter. PhotoRec asks you select the type of partition to search. In most cases (ext2/3, NTFS, FAT, etc.) you should select Intel and press Enter. You are given a list of the partitions on your selected hard drive. If you want to recover all of the files on a partition, then select Search and hit enter. However, this process can be very slow, and in our case we only want to search for pictures files, so instead we use the right arrow key to select File Opt and press Enter. PhotoRec can recover many different types of files, and deselecting each one would take a long time. Instead, we press “s” to clear all of the selections, and then find the appropriate file types – jpg, gif, and png – and select them by pressing the right arrow key. Once we’ve selected these three, we press “b” to save these selections. Press enter to return to the list of hard drive partitions. We want to search both of our partitions, so we highlight “No partition” and “Search” and then press Enter. PhotoRec prompts for a location to store the recovered files. If you have a different healthy hard drive, then we recommend storing the recovered files there. Since we’re not recovering very much, we’ll store it on the Ubuntu Live CD’s desktop. Note: Do not recover files to the hard drive you’re recovering from. PhotoRec is able to recover the 20 pictures from the partitions on our hard drive! A quick look in the recup_dir.1 directory that it creates confirms that PhotoRec has recovered all of our pictures, save for the file names. Foremost Foremost is a command-line program with no interactive interface like PhotoRec, but offers a number of command-line options to get as much data out of your had drive as possible. For a full list of options that can be tweaked via the command line, open up a terminal (Applications > Accessories > Terminal) and type in: foremost –h In our case, the command line options that we are going to use are: -t, a comma-separated list of types of files to search for. In our case, this is “jpeg,png,gif”. -v, enabling verbose-mode, giving us more information about what foremost is doing. -o, the output folder to store recovered files in. In our case, we created a directory called “foremost” on the desktop. -i, the input that will be searched for files. This can be a disk image in several different formats; however, we will use a hard disk, /dev/sda. Our foremost invocation is: sudo foremost –t jpeg,png,gif –o foremost –v –i /dev/sda Your invocation will differ depending on what you’re searching for and where you’re searching for it. Foremost is able to recover 17 of the 20 files stored on the hard drive. Looking at the files, we can confirm that these files were recovered relatively well, though we can see some errors in the thumbnail for 00622449.jpg. Part of this may be due to the ext2 filesystem. Foremost recommends using the –d command-line option for Linux file systems like ext2. We’ll run foremost again, adding the –d command-line option to our foremost invocation: sudo foremost –t jpeg,png,gif –d –o foremost –v –i /dev/sda This time, foremost is able to recover all 20 images! A final look at the pictures reveals that the pictures were recovered with no problems. Scalpel Scalpel is another powerful program that, like Foremost, is heavily configurable. Unlike Foremost, Scalpel requires you to edit a configuration file before attempting any data recovery. Any text editor will do, but we’ll use gedit to change the configuration file. In a terminal window (Applications > Accessories > Terminal), type in: sudo gedit /etc/scalpel/scalpel.conf scalpel.conf contains information about a number of different file types. Scroll through this file and uncomment lines that start with a file type that you want to recover (i.e. remove the “#” character at the start of those lines). Save the file and close it. Return to the terminal window. Scalpel also has a ton of command-line options that can help you search quickly and effectively; however, we’ll just define the input device (/dev/sda) and the output folder (a folder called “scalpel” that we created on the desktop). Our invocation is: sudo scalpel /dev/sda –o scalpel Scalpel is able to recover 18 of our 20 files. A quick look at the files scalpel recovered reveals that most of our files were recovered successfully, though there were some problems (e.g. 00000012.jpg). Conclusion In our quick toy example, TestDisk was able to recover two deleted partitions, and PhotoRec and Foremost were able to recover all 20 deleted images. Scalpel recovered most of the files, but it’s very likely that playing with the command-line options for scalpel would have enabled us to recover all 20 images. These tools are lifesavers when something goes wrong with your hard drive. If your data is on the hard drive somewhere, then one of these tools will track it down! Similar Articles Productive Geek Tips Recover Deleted Files on an NTFS Hard Drive from a Ubuntu Live CDUse an Ubuntu Live CD to Securely Wipe Your PC’s Hard DriveReset Your Ubuntu Password Easily from the Live CDBackup Your Windows Live Writer SettingsAdding extra Repositories on Ubuntu TouchFreeze Alternative in AutoHotkey The Icy Undertow Desktop Windows Home Server – Backup to LAN The Clear & Clean Desktop Use This Bookmarklet to Easily Get Albums Use AutoHotkey to Assign a Hotkey to a Specific Window Latest Software Reviews Tinyhacker Random Tips DVDFab 6 Revo Uninstaller Pro Registry Mechanic 9 for Windows PC Tools Internet Security Suite 2010 Awe inspiring, inter-galactic theme (Win 7) Case Study – How to Optimize Popular Wordpress Sites Restore Hidden Updates in Windows 7 & Vista Iceland an Insurance Job? Find Downloads and Add-ins for Outlook Recycle !

    Read the article

  • Oracle Linux Events in December

    - by Zeynep Koch
    December will be a busy month for Oracle Linux team. We will be showcasing Oracle Linux and Oracle VM in conferences all around the world. Here's a list of December events we will showcase Oracle Linux: Gartner Data Center – North America Oracle will have a session and booth - Register today Dec 3-6, Las Vegas, USA 0 0 1 66 377 Oracle Corporation 3 1 442 14.0 96 Normal 0 false false false EN-US JA X-NONE /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-priority:99; mso-style-parent:""; mso-padding-alt:0in 5.4pt 0in 5.4pt; mso-para-margin:0in; mso-para-margin-bottom:.0001pt; mso-pagination:widow-orphan; font-size:10.0pt; font-family:"Times New Roman";} Oracle Open World Latin America Oracle OpenWorld Latin America December 4–6, Sao Paulo, Brazil 0 0 1 25 145 Oracle Corporation 1 1 169 14.0 96 Normal 0 false false false EN-US JA X-NONE /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-priority:99; mso-style-parent:""; mso-padding-alt:0in 5.4pt 0in 5.4pt; mso-para-margin:0in; mso-para-margin-bottom:.0001pt; mso-pagination:widow-orphan; font-size:10.0pt; font-family:"Times New Roman";} HP Discover EMEA HP Discover – EMEA December 4 – 6, Messe Frankfurt, Germany (Oracle Platinum sponsor) 0 0 1 41 239 Oracle Corporation 1 1 279 14.0 96 Normal 0 false false false EN-US JA X-NONE /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-priority:99; mso-style-parent:""; mso-padding-alt:0in 5.4pt 0in 5.4pt; mso-para-margin:0in; mso-para-margin-bottom:.0001pt; mso-pagination:widow-orphan; font-size:10.0pt; font-family:"Times New Roman";} Oracle Superior Solutions and Cost Savings with Oracle Linux and Oracle VM See Location Details and register Dec 4 Kansas City and Tampa Dec 6 Milwaukee and Miami Dec 11 Washington, DC Dec 13 Raleigh Visit our booth and you can grab an Oracle Linux/Oracle VM DVD Kit and talk to Oracle Linux experts.

    Read the article

  • New Article on OTN: Tips for Securing an Oracle Linux Environment

    - by Lenz Grimmer
    Some time ago, we published Tips for Hardening an Oracle Linux Server on the Oracle Technology Network. This article focused on hardening an Oracle Linux system right after the initial installation, exploring administrative approaches that help to minimize vulnerabilities. This week we issued a second part,Tips for Securing an Oracle Linux Environment, which focuses on the operational part: detecting intrusion attempts, auditing and keeping systems up-to date and protected. If you manage Oracle Linux systems in your environment, check out these articles for some invaluable hints and suggestions on how to improve and maintain security of these servers!

    Read the article

  • How to Combine Rescue Disks to Create the Ultimate Windows Repair Disk

    - by The Geek
    We’ve covered loads of different anti-virus, Linux, and other boot disks that help you repair or recover your system, but why limit yourself to just one? Here’s how to combine your favorite repair disks together to create the ultimate repair toolkit for broken Windows systems—all on a single flash drive. The ones we’ve covered already? Here’s a quick list of all the ways you can recover your system with a rescue disk: How to Use the Avira Rescue CD to Clean Your Infected PC How to Use the BitDefender Rescue CD to Clean Your Infected PC How to Use the Kaspersky Rescue Disk to Clean Your Infected PC Change or Reset Windows Password from a Ubuntu Live CD The 10 Cleverest Ways to Use Linux to Fix Your Windows PC Change Your Forgotten Windows Password with the Linux System Rescue CD Use Ubuntu Live CD to Backup Files from Your Dead Windows Computer If you need to clean up an infected system, we’d absolutely recommend the BitDefender CD, since it’s auto-updating. Best bet? Create your ultimate boot disk with as many of the different utilities as your flash drive can hold Latest Features How-To Geek ETC How To Boot 10 Different Live CDs From 1 USB Flash Drive The 20 Best How-To Geek Linux Articles of 2010 The 50 Best How-To Geek Windows Articles of 2010 The 20 Best How-To Geek Explainer Topics for 2010 How to Disable Caps Lock Key in Windows 7 or Vista How to Use the Avira Rescue CD to Clean Your Infected PC Luigi Installs Any OS on Google’s Cr-48 Notebook DIY iPad Stylus Offers Pen-Based Interaction on the Cheap Serene Blue Ubuntu Wallpaper for Your Desktop Enjoy Old School Style Video Game Fun with Chicken Invaders Hide the Twitter “Litter” in Twitter’s Sidebar Area (Chrome and Iron) Public Domain Day: Reflections on Copyright and the Importance of Public Domain

    Read the article

  • Bash prompt doesn't print until I interact with console again

    - by durron597
    I don't even know where to begin to diagnose this one. Usually, when a command finishes, the prompt prints itself for the next command. However, that is not happening. Hard to explain with words, I'll just use an example: User@Machine:~$ cp /mnt/mountname/directory/textfile.txt . After waiting several seconds (far too long for this operation on a small file) I press Enter, and see: User@Machine:~$ cp /mnt/mountname/directory/textfile.txt . User@Machine:~$ User@Machine:~$ So clearly the operation had finished, but the prompt didn't display... until I pressed enter, and then BOTH prompts instantly displayed. This error does not happen with commands like cd.

    Read the article

  • VISIT ORACLE LINUX PAVILION @ORACLE OPENWORLD

    - by Zeynep Koch
    Back by popular demand, Oracle will again host the Oracle Linux Pavilionat Oracle OpenWorld from October 1-3. The pavilion will be located in the Exhibition Hall at Moscone South, Booth 1033, next to the Oracle DEMOgrounds and Oracle Linux demopods. At the pavilion a select group of ISVs, IHVs, and SIs will showcase their products that have been Oracle Linux- and/or Oracle VM-certified. These certified products enable customer applications to run faster, thereby saving money.Partners exhibiting their solutions in the Oracle Linux Pavilion include: BeyondTrust: context-aware security intelligence for dynamic IT infrastructures such as cloud, mobile, and virtual technologies Centrify: control, secure, and audit access to cross-platform systems, mobile devices, and applications Data Intensity: cloud services and application management Fujitsu: technology platforms, private cloud, services, ubiquitous and device solutions HP: converged cloud, converged infrastructure, application transformation, and information optimization LSI: intelligent solid-state storage solutions for breakthrough database acceleration Mellanox: InfiniBand and Ethernet end-to-end server and storage interconnect solutions and services for data centers Micro Focus: mainframe solutions, application modernization and development tools, software quality tools NetApp: storage and data management QLogic: high performance networking Teleran: BI and data warehouse management solutions for Oracle Exadata Database Machine and Oracle Database Be sure to pick up your free Oracle Linux and Oracle VM DVD Kit if you visit one of these partners. And speaking of free, be sure to stop by for some cool treats, courtesy of sponsor QLogic: Smoothie Bar on Monday, October 1 from 2:30 p.m. - 5:30p.m. Ice Cream Social on Wednesday, October 3 from 1:00 p.m. - 2:00 p.m. We look forward to seeing you at the pavilion.

    Read the article

  • Ubuntu Server available updates

    - by Rapture
    In Ubuntu 11.04 Server when I would log in via ssh it would tell me how many packages are available for updating in the welcome message. After upgrading to 11.10 I no longer get that information. Is there a package I need to install or a config file that needs changing? 11.04 output: Welcome to Ubuntu 11.10 (GNU/Linux 3.0.0-12-generic x86_64) * Documentation: https://help.ubuntu.com/ 32 packages can be updated. 8 updates are security updates. Last login: Mon Nov 21 16:19:01 2011 from han-solo.local 11.10 output: Welcome to Ubuntu 11.10 (GNU/Linux 3.0.0-12-server x86_64) * Documentation: https://help.ubuntu.com/11.10/serverguide/C No mail. Last login: Tue Nov 22 19:07:19 2011 from han-solo.local

    Read the article

  • Linux Mint is Brilliant

    - by Simon Moon
    Most of my blog posts sound way too whiny. I'm not that guy. (Am I?) I've been using SUSE-flavored Linux for personal projects since 2002 (SUSE Linux 8.1). This past weekend, I made the heart-wrenching decision to abandon openSUSE (version 12.1) in favor of Linux Mint (version Maya). OpenSUSE had just become too burdensome. Packages that installed easily on RedHat or Debian always had issues running on top of OpenSUSE. And I never could get the Heroku Toolbelt installed in any kind of usable state.And so, ...I'm beginning again with this enticing young thing -- Mint with the Cinnamon window environment. Delicious. And while I'll always have fond memories of my years with openSUSE, I've got to admit that Mint makes running Linux feel good again. http://blog.linuxmint.com/?p=2031

    Read the article

  • Black screen on login, can get thru decrypt disk and access command line but no GUI

    - by t3lf3c
    Running 12.04 64 bit fresh alternative install, with disk crypto on a new Lenovo laptop Install didn't connect and install modules, even though I had the network cable plugged in and don't have any whacky proxy settings. I had to manually install ubunut-desktop and define sources after initial installation, so this seemed a bit weird (ISO matched MD5 sum though) I unplug the network cable, otherwise I get a black screen that I can do nothing with. So I turn laptop on, I have disk encryption, I type in the password at the Ubuntu decryption GUI then get "set up successfully" message "Waiting for network configuration ..." then "Waiting for up to 60 more seconds for network configuration" At this stage (a) If I wait for it then I get a black screen that I can do nothing with. (b) If I interrupt the process by pressing escape, then I break through to the command line. From the command line, I can go ahead and login, then plug my network cable in to do apt-get commands. As a precaution I do some house keeping which takes a few mins to run: sudo apt-get update sudo apt-get upgrade Running startx to get to the GUI gives: Fatal server errror: no screens found The .Xauthority file is being created in my home directory but it's empty. I review my order and note the system graphics: Intel HD Graphics (WWAN or mSATA capable) So it's weird that I can't get to the Gnome. It looks like drivers aren't working. Is there a way of getting Intel drivers from the command line? Or do you have any other suggestions on what to try next?

    Read the article

  • Oracle Linux Partner Pavilion Spotlight

    - by Ted Davis
    With the first day of Oracle OpenWorld starting in less than a week, we wanted to showcase some of our premier partners exhibiting in the Oracle Linux Partner Pavilion ( Booth #1033) this year. We have Independent Hardware Vendors, Independent Software Vendors and Systems Integrators that show the breadth of support in the Oracle Linux and Oracle VM ecosystem. We'll be highlighting partners all week so feel free to come back check us out. Centrify delivers integrated software and cloud-based solutions that centrally control, secure and audit access to cross-platform systems, mobile devices and applications by leveraging the infrastructure organizations already own. From the data center and into the cloud, more than 4,500 organizations, including 40 percent of the Fortune 50 and more than 60 Federal agencies, rely on Centrify's identity consolidation and privilege management solutions to reduce IT expenses, strengthen security and meet compliance requirements. Visit Centrify at Oracle OpenWorld 2102 for a look at Centrify Suite and see how you can streamline security management on Oracle Linux.  Unify identities across the enterprise and remove the pain and security issues associated with managing local user accounts by leveraging Active Directory Implement a least-privilege security model with flexible, role-based controls that protect privileged operations while still granting users the privileges they need to perform their job Get a central, global view of audited user sessions across your Oracle Linux environment  "Data Intensity's cloud infrastructure leverages Oracle VM and Oracle Linux to provide highly available enterprise application management solutions.  Engineers will be available to answer questions about and demonstrate the technology, including management tools, configuration do's and don'ts, high availability, live migration, integrating the technology with Oracle software, and how the integrated support process works."    Mellanox’s end-to-end InfiniBand and Ethernet server and storage interconnect solutions deliver the highest performance, efficiency and scalability for enterprise, high-performance cloud and web 2.0 applications. Mellanox’s interconnect solutions accelerate Oracle RAC query throughput performance to reach 50Gb/s compared to TCP/IP based competing solutions that cap off at less than 12Gb/s. Mellanox solutions help Oracle’s Exadata to deliver 10X performance boost at 50% Hardware cost making it the world’s leading database appliance. Thanks for reviewing today's Partner spotlight. We will highlight new partners each day this week leading up to Oracle OpenWorld.

    Read the article

  • What commands are needed to install Ubuntu Core?

    - by Oxwivi
    Ubuntu Core's wiki page page contains the instructions to install Ubuntu Core on a target media: Uncompress (do not unpack) rootfs Format target media: at least one partition should be ext2, ext3, or ext4 Unpack Ubuntu Core to ext{2,3,4} partition Install boot-loader Install Linux If the Linux kernel requires modules, add these to /lib/modules/$(uname -r) in the ext{2,3,4} file system Boot the target device Install any additional required software using apt-get But what are the specific commands to do the above? The things I'm specifically confused about are: Uncompressing and unpacking, what's the difference and how do I do them? What package should I install if I want the generic kernel provided in regular Ubuntu installation? I won't be installing any drivers or anything related to kernel other than what's provided in the repos, do I need to worry about manually adding kernel modules? PS I would like to request that all the commands used in the installation process be mentioned in the answer, for the benefit of ones who're completely unfamiliar and myself, should I ever forget.

    Read the article

  • Commercial Gaming, Coming Soon to Linux?

    <b>Linux Magazine:</b> "The inability to play the latest off the shelf commercial games has been a thorn in the side of Linux for a long time. With companies such as Valve starting to embrace other platforms, will that be the catalyst Linux needs to become a first class citizen? "

    Read the article

  • Oracle Linux Pavilion is Back for Oracle OpenWorld

    - by Oracle OpenWorld Blog Team
    By Zeynep Koch Back by popular demand, Oracle will again host the Oracle Linux Pavilion at Oracle OpenWorld from October 1-3. The pavilion will be located in the Exhibition Hall at Moscone South, Booth 1033, next to the Oracle DEMOgrounds and Oracle Linux demopods. At the pavilion a select group of ISVs, IHVs, and SIs will showcase their products that have been Oracle Linux- and/or Oracle VM-certified. These certified products enable customer applications to run faster, thereby saving money.Partners exhibiting their solutions in the Oracle Linux Pavilion include: BeyondTrust: context-aware security intelligence for dynamic IT infrastructures such as cloud, mobile, and virtual technologies Centrify: control, secure, and audit access to cross-platform systems, mobile devices, and applications Data Intensity: cloud services and application management Fujitsu: technology platforms, private cloud, services, ubiquitous and device solutions HP: converged cloud, converged infrastructure, application transformation, and information optimization LSI: intelligent solid-state storage solutions for breakthrough database acceleration Mellanox: InfiniBand and Ethernet end-to-end server and storage interconnect solutions and services for data centers Micro Focus: mainframe solutions, application modernization and development tools, software quality tools NetApp: storage and data management QLogic: high performance networking Teleran: BI and data warehouse management solutions for Oracle Exadata Database Machine and Oracle Database Be sure to pick up your free Oracle Linux and Oracle VM DVD Kit if you visit one of these partners. We look forward to seeing you at the pavilion.

    Read the article

  • Adding a Wine (.exe) file to open/play files in Thunar's 'Custom Actions'

    - by cipricus
    What is the line parameter in Thunar's "custom actions" that would play a music directory in a Wine (.exe) program? I want to put Foobar2000 (and possibly other such applications) in Thunar's Custom Actions (actions that can be added/edited to be used in the context menu to play music folder's content). If I put no command parameter at the end of path, the player opens but there is no play and no files in the play list. If I add any of the listed parameters I get the error unknown commandline parameter: /path.to.file (Giving an answer to this question depends on knowing the CLI command that would have to be added into Thunar - so please look at this question too)

    Read the article

< Previous Page | 172 173 174 175 176 177 178 179 180 181 182 183  | Next Page >