Search Results

Search found 19557 results on 783 pages for 'networking programming'.

Page 176/783 | < Previous Page | 172 173 174 175 176 177 178 179 180 181 182 183  | Next Page >

  • Why is Wifi data transfer is slow?

    - by Ali Azam Rana
    I have a wifi router which was attached with my modem, and the pc was connected to the wifi router through an ethernet cable. Yesterday I moved my modem and router to another room and connected my PC with wifi through an external wifi usb dongle (tp-link tl-w722n). I noticed that the file transfer speed from my cell to PC via wifi is greatly affected. I am not clear why is this happening because although PC is now connected through wifi but the dongle supports more than 54Mbps which is still enough.

    Read the article

  • How can I join two simple home networks together using an ethernet cable?

    - by Ilia Jerebtsov
    I want to join two different home networks together like so: PC A1 PC A2 PC B1 PC B2 \ / \ / Gateway A <----- ethr. cable -----> Gateway B | | ADSL modem A ADSL modem B Both networks are of the basic residential type with identical configuration, with all PCs running Vista/7. The point is to temporarily join two apartments in a building for gaming and file sharing, and the holy grail would be: PCs on network A can access PCs on network B and vice-versa (file shares and gaming). Each network uses its own internet connection. Data between networks shouldn't take a trip through the internet (broadband upload speeds are severely capped) A network's internet access should continue working if the joining cable is disconnected with minimal configuration changes. How closely can this be achieved?

    Read the article

  • Could a HomePlug be used to connect 2 routers?

    - by tigermain
    I have 2 routers that I would like to connect together (they are wireless but dont have an AP mode) could I simply buy a pair of homeplugs and connect them in order for all machines to have complete visibility of each other?! The DHCP will only be enabled on one, so the other will simply be acting as a switch

    Read the article

  • Why do I often have to refresh pages I navigate to once for them (or content in them) to load?

    - by GetOutOfBox
    I have noticed a bizarre pattern when using my PC, that when I open a link to a website, it often will often take a very long time to load, or time out. Sometimes content on the website will be drawn, but again, it seems to get "stuck" for an unusual amount of time before finishing. Most affected is Youtube; almost every time I navigate to a youtube video from another website such as Google, the video will not begin playing, but will instead just display the player controls with a black screen where the video should be and the buffering symbol, usually before displaying an error such as "The video failed to load". The unusual part of this problem is that whenever this happens, refreshing the page always causes it to load almost immediately the second time around, without any problems. Note that I'm not talking about how some browsers will dump whatever has been cached to the "pallet" briefly when the page is refreshed or loading stopped; but that the second time loading the website being faster. I have done my best to rule out some of the obvious causes: My Windows 7 desktop computer is the only device that seems to be affected. I use Firefox on it (latest version, flash updated, etc). My connection has more than enough bandwidth (30 megabits down, 4 up), and I've even tried QoSing all other devices to make sure this isn't happening due to usage spikes. Wireshark is not showing any clearly unusual network activity (i.e frequently dropped packets).

    Read the article

  • Ping server NETBIOS name returns wrong IP and "Destination host unreachable"

    - by music2myear
    Problem server is Windows 2008 R2 VM running on VMWare ESXi 4 host. Single network adapter manually assigned single IP address (192.168.1.11). When I ping the server from any other network computer, it returns 192.168.1.124 and "Destination host unreachable". Yesterday I found a second network adapter assigned to this server with an IP of 169.254... indicating it had no real valid IP. Using the MAC addresses I determined which adapter was not needed/not wanted, and removed it using VMWare systems. This is the network Printer Server and, understandably, nothing is printing right now. I've looked at the solutions here Why was my ping answered by a different IP address than the one pinged? and they aren't applicable to my situation for the following reasons: Output of arp -a on another computer returns the correct IP address (.1.11) assigned to the correct MAC address, the incorrect IP .1.124 is not listed, and the MAC of the network adapter I removed yesterday is not listed at all. I checked out the Microsoft KB article which listed pretty much my exact symptoms ( http://support.microsoft.com/kb/981953 ) and it says to check binding orders and look for hidden adapters. But there are no hidden adapters, and there is only one Network Adapter listed in the Binding Order list. Essentially, I can communicate from the server TO any other network device, but I cannot communicate from any other network device TO the server. Help! UPDATE: Solution found, see this solution for the details.

    Read the article

  • Latency in TCP/IP-over-Ethernet networks

    - by aix
    What resources (books, Web pages etc) would you recommend that: explain the causes of latency in TCP/IP-over-Ethernet networks; mention tools for looking out for things that cause latency (e.g. certain entries in netstat -s); suggest ways to tweak the Linux TCP stack to reduce TCP latency (Nagle, socket buffers etc). The closest I am aware of is this document, but it's rather brief. Alternatively, you're welcome to answer the above questions directly. edit To be clear, the question isn't just about "abnormal" latency, but about latency in general. Additionally, it is specifically about TCP/IP-over-Ethernet and not about other protocols (even if they have better latency characteristics.)

    Read the article

  • Force10 S60 remote management

    - by StaringSkyward
    We've got a Force10 S60 switch to replace an older Cisco. I can't find a way to give the switch itself an IP address on the local VLAN so I can ssh to it. The config guide talks about using either a management interface on a separate management network or dedicating e.g. a gigabit port as a management port with a dedicated IP address. Ideally I would like to do what we do currently with the Cisco switches, which is in effect give the entire switch an IP so it can be reached from any host on the same VLAN without having to use up a physical port on the switch or physically connect the management port to another device. Is this possible with the S60 and if so, how would you give it, say the address 10.0.1.1 in vlan 10 (10.0.1.1/24)? Thanks!!!

    Read the article

  • How to route to a secondary interface on the same physical ethernet?

    - by sjose3612611
    INTERNET<->(wan)BRIDGED_DEVICE(lan)<->ETH_ROUTER<->LAN Problem: Need to access web server on BRIDGED_DEVICE's LAN from INTERNET via ROUTER (BRIDGED_DEVICE's web server cannot be accessed form INTERNET since it has no Public management IP). Cannot configure bridged device. It has a static IP on its LAN to which its web server binds. Attempt: Create a secondary/alias WAN Interface on ETH_ROUTER (e.g Primary: eth0.1 (for internet access) and Secondary: eth0.2 (for accessing web server on BRIDGED_DEVICE), (No VLANs). eth0.1 has a public IP; eth0.2 has a static private IP in the BRIDGED_DEVICE's subnet (e.g 10.0.X.Y). Iptables on ETH_ROUTER: Added a port forward (DNAT) from eth0.1 to eth0.2: iptables -t nat -I PREROUTING -i eth0.1 -p tcp --dport 80 -j DNAT --to-destination 10.0.X.Y iptables -t nat -I POSTROUTING -o eth0.2 -s 10.0.X.0/24 -j MASQUERADE Stateful firewall w/ overall drop policy on FORWARD chain, hence: iptables -I FORWARD -i eth0.1 -d 10.0.X.Y -p tcp --dport 80 -j ACCEPT Can ping from ETH_ROUTER to BRIDGED_DEVICE but unable to reach the web server from Internet. I see packet cont increasing for the DNAT rule but not sure where it disappears in the ETH_ROUTER after that. ETH_ROUTER is the only device that can be configured to achieve this. If familiar with this scenario, please suggest what I may be missing or doing wrong here or suggest techniques to debug?

    Read the article

  • What decent small-office level routers are there

    - by Glenn Slaven
    So let's say I have a network of less than 20 computers including a server that needs to be accessed externally. What router/firewall solutions would you recommend? It can be either hardware or software and would need to be able to do NAT Firewall DMZ Native VPN if possible Some form of network bandwidth monitoring Update: I've accepted the answer I liked but this question probably doesn't have a definitive answer, it would depend on your requirements. Please leave more suggestions with an explanation as to why it works well in your situation.

    Read the article

  • Home-Router: Access internal server using external ip [migrated]

    - by user15863
    If I've got a typical home router -- say a Net Gear -- which has certain ports forwarded to a internal server, is there a way to tweak the router to let me access that internal server using the external IP address from within the same network? Is there a non-enterprise grade router that can handle this type of thing? In case that was strangely worded, let me re-phrase with an example. My external IP is 1.2.3.4. My internal server is 10.4.3.100 Port 1178 is being forwarded from the router to 10.4.3.100. I'd like to be able to be able to hit 10.4.3.100 from an internal ip of 10.4.3.10 by using the external ip of 1.2.3.4. Possible?

    Read the article

  • SMB super slow within LAN between MAC and PC

    - by asdcasdc
    I have a windows desktop which stores all my movies, songs and pictures. I have a mac laptop which I would like to access these files. I don't want to utilize the FTP or SCP protocol because I don't want them to be downloaded to my mac. I want to access them as if they are a network mounted disk. So I tried using the native SMB protocol (available in Finder - Go - Connect to server). I tried dragging a file and dropping it onto my MAC's desktop. Surprisingly, I am only able to transfer at a very slow rate of about 1mb/s. Assuming network connectivity is not a problem, has anyone experienced incredible slowness with SMB? Are there alternative protocols for me to use in this case between PC and MAC?

    Read the article

  • What services does hosts.allow NOT affect?

    - by Jed Daniels
    I know that hosts.allow and host.deny only affect things that are tcpwrappered, but what does this mean in practice? It seems that most people use hosts.allow to handle ssh and nfs blocking, but what other services are typically handled there? And what services AREN'T typically handled there? Edit: ok, I realize I did a terrible job of explaining what I was after. No, I'm not interested in knowing if a particular service can be handled by hosts.allow, I want to know if a service will be handled. For example, if I do an lsof -i, I get a nice list of things that are listening for connections to my box. I want to know which ones will be affected if I go stick an entry into hosts.allow (well, I really want to know which ones won't be affected).

    Read the article

  • "Automatically Connect" option for Mobile Broadband crashes GNOME Shell, how to remove network configurations?

    - by Kush
    I'm using Fedora 15, in GNOME Shell, my mobile broadband connection was working absolutely fine, until I set the connection type to Connect Automatically using nm-connection-manager. Now, when I start the Fedora, the Top panel network icon shows red exclamation symbol and when I click it, instead of showing me available networks' list, it shows only "Network Settings", and when I open it, it shows GNOME 3's new Network Manager app, and it pops out the dialog saying that, "Current network settings service is incompatible with this version". And after a few seconds of log in, the shell freezes and all I can do is log out using Ctrl+Alt+BackSpace. I'm facing this problem since I opened old network manager app using nm-connection-manager in the run dialog, and editing my connection to connect automatically. After logging in to the shell I somehow managed to delete that connection from the same app and created a new one, but the problem still exists. How can I delete all network preferences (by deleting its configuration files from my home directory or something like that) and reset the GNOME 3's network manager to its default state?

    Read the article

  • Verify server performance

    - by George Kesler
    I'm looking for a quick and SIMPLE way to verify that new servers are performing as expected. The most important metric is disk performance, second is network performance. I’m trying to prevent problems caused by misconfiguration of RAID arrays, NIC teaming etc. The solution should work with both physical and virtual servers. I don’t need sophisticated analysis with different workloads, just one set of benchmarks which I would run against a reference server and later compare to new ones. One problem is that most benchmarks are not giving accurate results when running on a VM.

    Read the article

  • Display wireless channels currently in use

    - by DrStalker
    Is there any windows utility to display the wireless channels are currently in use by the available wireless networks? I'd like to be able to see what existing channels are using so I can try to minimize interference on a new access point without a lot of trial and error.

    Read the article

  • Sharing a printer over the net from Windows 7 to Windows Server 2003

    - by Grant Unwin
    Hi, I need to share a printer that is connected to a Windows 7 computer. The windows 7 computer is in another building about an hours drive away. The computer that needs to access the printer is running Windows Server 2008. Ive tried setting the printer as 'shared' for 'everyone' on the Windows 7 PC and accessing it from the server by adding a TCP/IP port to the IP address but the printer just wont add. From googling aparently it may need setting up as a printer server through IIS, but i'm just not sure on the best practice. Any help greatly appreciated. Thanks Grant Unwin

    Read the article

  • Why DELL PowerConnect and Juniper are so rare ? Why do enterprises stick with Cisco ?

    - by Kedare
    Hello ! I have a little question, I'm actually studing IT in France, and when looking on alternative on the very [...] very expensive Cisco equipments, I've found Juniper and DELL PowerConnect pretty attractive on features and price, but I rarely see something else than the classics Cisco/LinkSys, HP Procurve and Netgear.. Why it's so rare to find those switch ? They looks really great but... I've never seen any Juniper or Powerconnect... Why do enterprises stick with the expensive Cisco ? I've tried to find how to buy both, it's quite easy with PowerConnect, everything is on the DELL website, but it looks it's very hard to find Juniper equipments in France :( Thank you !

    Read the article

  • What are the challenges when my enterprise desires to move the processing component of an applicatio

    - by Berkay
    Assume that i have an enterprise accounting application that consists of a front-end interface, a processing tier, and a back-end database. This is an application that contains private business data, and thus is traditionally run in a secure private network environment within the enterprise. What are the challenges that appear when my enterprise desires to move the processing component of this application to a cloud computing data center in order to achieve greater scalability or to reduce IT costs ? Pls note: do i have to make significant changes to my own infrastructure to enable external access to formerly private resources? do i have to modify the application code to handle new network topology ? thanks, if you give your answers in a simple manner, really appreciated.

    Read the article

  • PXE Boot not working

    - by Nishant
    Please explain the error in this screenshot DHCP Setting: This screenshot was taken after powering off the old comp hence he server interface is shown as the wireless card - it becomes 192.168.0.1 when I connect wires and power up the old laptop to boot via PXE. My scenario is simple. An old laptop and a new laptop . A cross over cable ( that I myself made from CAT 6 cable by cutting it and connecting 4 wires as mentioned in some doc). The new laptop ( tftp server ) has a Wirelss Card ( with which I am browsing and writing this ) . And the cable is connected between laptops . TFTP server ( new laptop details ) Windows IP Configuration Ethernet adapter Local Area Connection: Connection-specific DNS Suffix . : Link-local IPv6 Address . . . . . : fe80::f511:3d4a:ca01:122e%16 IPv4 Address. . . . . . . . . . . : 192.168.0.1 Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : 192.168.0.2 Wireless LAN adapter Wireless Network Connection: Connection-specific DNS Suffix . : Achilles Link-local IPv6 Address . . . . . : fe80::99b1:8ae0:9e6c:f300%11 IPv4 Address. . . . . . . . . . . : 192.168.2.3 Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : 192.168.2.1

    Read the article

  • Running docker in VPC and accessing container from another VPC machine

    - by Bogdan Gaza
    I'm having issues while running docker in AWS VPC. Here is my setup: I've got two machines running in VPC: 10.0.100.150 10.0.100.151 both having an elastic IPs assigned to them, both running in the same internet enabled subnet. Let's say I'm running a web server that serves static files in a container on the 10.0.100.150 machine the container: IP: 172.17.0.2 port 8111 is forwarded on the 8111 port on the machine. I'm trying to access the static files from my local machine (or another non-VPC machine also tried an EC2 instance not running in the VPC) and it work flawlessly. If I try to access the files from the other machine (10.0.100.151) it hangs. I'm using wget to pull the files. Tried to debug it with tcpdump and ngrep and that I have seen is that the request reaches the container. If I ngrep on the host machine I see the requests going in but no response going back. If I ngrep on the container I see the requests going in and the response going back. I've tried multiple iptables setups (with postrouting enabled, with manually forwarding ports etc) but no success. Help in any way - even debugging directions would be much appreciated. Thanks!

    Read the article

  • Unable to connect to cable modem when connected to VPN

    - by Spuas
    the scenario is as follows: First I have a cable modem which gives the internet connection. The network is 192.168.0.0/24 and its IP is 192.168.0.1 Second line, I have a router connected to the cable modem. Its "outside" IP is 192.168.0.12. This router creates network 192.168.123.0/24 and its IP there is 192.168.123.254. My computer is wired to the router with IP 192.168.123.126. At this point I am able to access both devices web interfaces by their IPs on a browser (192.168.123.254 for the router and 192.168.0.1 for the cable modem). The problem I have is when I connect to a VPN from the computer. Then I am connected to a second network 10.0.0.0/24 and I get IP 10.0.0.200 (along with 192.168.123.126). I can connect to the router but then I loose connectivity to the cable modem: I cannot acces it through the browser, neither making a ping to it or a tracert. I have tried to add a new route to the windows routes by typing route ADD 192.168.0.1 MASK 255.255.255.0 192.168.123.254 but I cannot access it anyway... Am I missing something on the route adding? Which is the propper way of doing this? Thanks

    Read the article

  • snmptt not translating traps, even with translate_log_trap_oid=1

    - by mbrownnyc
    I am having some trouble configuring snmptt to properly translate snmp traps. The following is a problem: /etc/snmp/snmptt.conf reflects: EVENT fgFmTrapIfChange .1.3.6.1.4.1.12356.101.6.0.1004 "Status Events" Critical FORMAT $* EXEC /usr/local/nagios/libexec/eventhandlers/submit_check_result $r "snmp_traps" 2 "$O: $+*" "$*" SDESC Trap is sent to the managing FortiManager if an interface IP is changed Variables: 1: fnSysSerial 2: ifName 3: fgManIfIp 4: fgManIfMask EDESC when a trap is received, /var/log/messages reflects: Sep 6 12:07:32 SNMPMANAGERHOST snmptrapd[15385]: 2012-09-06 12:07:32 <UNKNOWN> [UDP: [192.168.100.2]:162->[192.168.100.31]]: #012.1.3.6.1.2.1.1.3.0 = Timeticks: (707253943) 81 days, 20:35:39.43 #011.1.3.6.1.6.3.1.1.4.1.0 = OID: .1.3.6.1.4.1.12356.101.6.0.1004 #011.1.3.6.1.4.1.12356.100.1.1.1.0 = STRING: FGTNNNNNNNNN #011.1.3.6.1.2.1.31.1.1.1.1.10 = STRING: internal4 #011.1.3.6.1.4.1.12356.101.6.2.1.0 = IpAddress: 192.168.65.100 #011.1.3.6.1.4.1.12356.101.6.2.2.0 = IpAddress: 255.255.255.0 Sep 6 12:07:37 SNMPMANAGERHOST icinga: EXTERNAL COMMAND: PROCESS_SERVICE_CHECK_RESULT; 192.168.100.2; snmp_traps; 2; enterprises.12356.101.6.0.1004: enterprises.12356.100.1.1.1.0:FGTNNNNNNNNN ifName.10:internal4 enterprises.12356.101.6.2.1.0:192.168.65.100 enterprises.12356.101.6.2.2.0:255.255.255.0 Since the icinga entry reflects the EXEC, it's obvious there is no translations occurring by snmptt. I have verified that translate_log_trap_oid and net_snmp_perl_enable is enabled in snmptt.ini When using --debug=1 to start snmptt, I see the following in the --debugfile: ********** Net-SNMP version 5.05 Perl module enabled ********** The main NET-SNMP version is reported as NET-SNMP version: 5.5. What else can be done to verify that snmptt is configured properly to translate traps? I have run snmptt-net-snmp-test to verify whatever net-snmp-perl version I have installed properly supports translations. The output indicates it does. /root/snmptt_1.3/snmptt-net-snmp-test --best_guess=2 SNMPTT Net-SNMP Test v1.0 (c) 2003 Alex Burger http://snmptt.sourceforge.net MIBS:RFC1213-MIB best_guess: 2 Testing translateObj ******************** Testing: .1.3.6.1.2.1.1.1, long_names=disabled, include_module=disabled Test passed. Result: sysDescr Testing: .1.3.6.1.2.1.1.1, long_names=disabled, include_module=enabled Test passed. Result: RFC1213-MIB::sysDescr Testing: .1.3.6.1.2.1.1.1, long_names=enabled, include_module=disabled Test passed. Result: .iso.org.dod.internet.mgmt.mib-2.system.sysDescr Testing: .1.3.6.1.2.1.1.1, long_names=enabled, include_module=enabled Test passed. Result: RFC1213-MIB::.iso.org.dod.internet.mgmt.mib-2.system.sysDescr Testing: sysDescr, long_names=disabled, include_module=disabled Test passed. Result: .1.3.6.1.2.1.1.1 Testing: RFC1213-MIB::sysDescr, long_names=disabled, include_module=disabled Test passed. Result: .1.3.6.1.2.1.1.1 Testing: system.sysDescr, long_names=disabled, include_module=disabled Test passed. Result: .1.3.6.1.2.1.1.1 Testing: RFC1213-MIB::system.sysDescr, long_names=disabled, include_module=disabled Test passed. Result: .1.3.6.1.2.1.1.1 Testing: .iso.org.dod.internet.mgmt.mib-2.system.sysDescr, long_names=disabled, include_module=disabled Test passed. Result: .1.3.6.1.2.1.1.1 Testing getType *************** Testing: .1.3.6.1.2.1.4.1 Test passed. Result: INTEGER Testing: ipForwarding Test passed. Result: INTEGER Testing Description ******************* Test passed. Result: ------------------------------------------------- The indication of whether this entity is acting as an IP gateway in respect to the forwarding of datagrams received by, but not addressed to, this entity. IP gateways forward datagrams. IP hosts do not (except those source-routed via the host). Note that for some managed nodes, this object may take on only a subset of the values possible. Accordingly, it is appropriate for an agent to return a `badValue' response if a management station attempts to change this object to an inappropriate value. ------------------------------------------------- I have manually gone through the MIB with the definition that's not resolving, and verified that it is properly linking back to the proper resolved definition. It is: FORTINET-FORTIGATE-MIB.txt contains: fgFmTrapIfChange NOTIFICATION-TYPE OBJECTS { fnSysSerial, ifName, fgManIfIp, fgManIfMask } STATUS current DESCRIPTION "Trap is sent to the managing FortiManager if an interface IP is changed" ::= { fgFmTrapPrefix 1004 } fgFmTrapPrefix OBJECT IDENTIFIER ::= { fgMgmt 0 } fgMgmt OBJECT IDENTIFIER ::= { fnFortiGateMib 6 } fnFortiGateMib ::= { fortinet 101 } IMPORTS FnBoolState, FnIndex, fnAdminEntry, fnSysSerial, fortinet FROM FORTINET-CORE-MIB fortinet MODULE-IDENTITY ::= { enterprises 12356 } LOOKS GOOD!!!!! 1.3.6.1.4.1.12356.101.6.0.1004 I've exhausted all the documentation and even posted fruitlessly in the snmptt-users mailing list. I can not prove it is the MIB. Why would snmptt fail to translate traps? Thanks, Matt

    Read the article

< Previous Page | 172 173 174 175 176 177 178 179 180 181 182 183  | Next Page >