Search Results

Search found 52700 results on 2108 pages for 'rounding error'.

Page 1785/2108 | < Previous Page | 1781 1782 1783 1784 1785 1786 1787 1788 1789 1790 1791 1792  | Next Page >

• New SSD, is the MBR broken? DISK BOOT FAILURE

  - by Shevek

  I've been running Windows 7 on a WD 500gb SATA single drive, single partition setup for some time with no issues. I've just installed a new Kingston V Series 64gb SSD and performed a clean install of Win7 to it, deleting the partitions on the 500gb and using that as a data drive. All was well for a few reboots but then I started to get "DISK BOOT FAILURE, INSERT SYSTEM DISK AND PRESS ENTER" messages. If I put the Win7 install DVD back in the drive it boots fine. Tried a clean install again, after replacing SATA cables and swapping SATA ports, with a complete partition wipe of both drives. Again, rebooted fine a few times then back with the "DISK BOOT FAILURE" error. Looked on the web and found some discussions about it so I then started from scratch again. This time I wiped the MBR on both drives using MBRWork, disconnected the 500gb and reinstalled to the SSD. Removed the install DVD and installed all the drivers which involved many reboots, all with no problem. To make sure I also did a few cold boots as well. Reconnected the 500gb, initialised, partitioned and formatted it. Copied data to it and did some more reboots and shutdowns. All was ok. Then out of the blue comes another "DISK BOOT FAILURE" and again, if the Win7 install DVD is in the drive it boots fine. So, is the SSD a bad'un? TIA UPDATE: It was a BIOS issue! I found a hidden away option for HDD boot order, which was separate from the usual HDD/CDRom/FDD boot order option. The WD was set to boot before the SSD... Swapped them round and all is well. Still don't understand how it worked at first though... Thanks Solaris

  Read the article

• DRBD setup problem

  - by cuthieu

  I'm so new to DRBD, please help me fixing the problem below. Enclosed my drbd.conf. Many thanks [root@skonkwerks1 ~]# drbdadm create-md all open(/dev/hdb3) failed: No such file or directory Command 'drbdmeta /dev/drbd0 v08 /dev/hdb3 internal create-md' terminated with exit code 20 drbdsetup exited with code 20 [root@skonkwerks1 ~]# vi /etc/drbd.conf global { usage-count no; } resource repdata { protocol C; startup { wfc-timeout 0; degr-wfc-timeout 120; } disk { on-io-error detach; } # or panic # net { cram-hmac-alg "hdd1"; shared-secret "testing"; } syncer { rate 10M; } on skonkwerks1 { device /dev/drbd0; disk /dev/hdb1; address 172.29.156.1:7788; meta-disk internal; } on skonkwerks2 { device /dev/drbd0; disk /dev/hdb1; address 172.29.156.2:7788; meta-disk internal; } }

  Read the article

• Windows Photo Viewer can't open this picture because you don't have the correct permissions to access the file location

  - by Software Monkey

  My system in Windows 7 and fully up to date with all patches and options (except for Microsoft Silverlight, which I refuse to install). I get this error whenever I try to open an image using Windows Photo Viewer, such as when previewing from Explorer or when opening an image attachment to an email. I have already verified correct permissions to the file and all folders in the path. The strange thing is that every other program I have seems to open the images fine, including "Slideshow" from Windows Explorer. Even more strange, in WPV there is an "Open" menu that lists the other programs for images including GIMP and MS Paint and they open the very file that WPV is complaining about just fine. That should eliminate permissions as being the problem, especially since (logically at least) they are read/write while WPV is read-only. I have even edited and saved the images that WPV does not open. I am out of ideas, and searching for answer on the Web has resulted only in the same tired repitition of some flavor of "take ownership and reset permissions for the entire drive", which I have already done. And which is counter-indicated by the fact that only Windows Photo Viewer seems to have a problem. The one thing which is slightly unusual is that for normal files they are all on a second HDD mounted into C:, however for email attachments the temporary folder is C:\Temp\, which is directly on that drive.

  Read the article

• Use of backreferences in fail2ban filters possible?

  - by Izzy

  From time to time, I see collections of suspect "File not found" errors in my Apache logs, basically using the pattern File does not exist: /var/www/file, referer: http://my.server.com/file In human terms: The file was not found, though it referenced here itself. A clear hacking attempt, as that's hardly possible (and the REQUEST_URIs often enough suggest the same). In my eyes a clear case for fail2ban – if I could get backreferences to work here: failregex = ^%(_apache_error_client)s File does not exist: /var/www(.+), referer: http://.+\1$ (Justin Case: above examples assume the DIRECTORY_ROOT of that webserver being /var/www) I googled for hours, searched the fail2ban wiki up and down – but nowhere I could find a statement concerning backreferences in its filters. Are they not supported, or did I do it the wrong way? Any hints how to make it work (except from "dirty hacks" like first sending the request to another fake url using mod-rewrite, and then catching on that (if anyone is interested, I can elaborate on that approach in an answer), or doing something similar using mod-security)? as an entire log line was requested: [Fri Nov 08 14:57:28 2013] [error] [client 50.67.234.213] File does not exist: /var/www/text/files.htm++++++++++++++++++++++++++Result:+using+proxy+27.34.142.47:9090;+no+post+sending+forms+are+found;, referer: http://www.myserver.com/text/files.htm++++++++++++++++++++++++++Result:+using+proxy+27.34.142.47:9090;+no+post+sending+forms+are+found; (sorry, logs were just switched, so this long candidate was the only one left currently; minor adjustments were made for privacy reasons)

  Read the article

• Need Help getting perl module DBD::mysql installed for bugzilla on RedHat.

  - by Alos Diallo

  Hi everyone I am having some issues getting Bugzilla setup, I have the software on the server and am trying to get the pre-rec's setup. I am using RedHat 4.1.2-42. I have all of the required perl modules save one:DBD::mysql When I try: sudo perl install-module.pl DBD::mysql I get the following response(this is only an excerpt): rm -f blib/arch/auto/DBD/mysql/mysql.so LD_RUN_PATH="/usr/lib64/mysql:/usr/lib64:/lib64" /usr/bin/perl myld gcc -shared -O2 -g -pipe -Wall -Wp,-D_FORTIFY_SOURCE=2 -fexceptions -fstack-protector --param=ssp-buffer-size=4 -m64 -mtune=generic dbdimp.o mysql.o -o blib/arch/auto/DBD/mysql/mysql.so \ -L/usr/lib64/mysql -lmysqlclient -lz -lcrypt -lnsl -lm -L/usr/lib64 -lssl -lcrypto \ /usr/bin/ld: skipping incompatible /usr/lib/libssl.so when searching for -lssl /usr/bin/ld: skipping incompatible /usr/lib/libssl.a when searching for -lssl /usr/bin/ld: cannot find -lssl collect2: ld returned 1 exit status make: * [blib/arch/auto/DBD/mysql/mysql.so] Error 1 /usr/bin/make -- NOT OK Running make test Can't test without successful make Running make install make had returned bad status, install seems impossible I then tried the following: CFLAGS="-I/usr/lib64/mysql:/usr/lib64:/lib64" perl install-module.pl DBD::mysql I get the same result. I have also tried to install it using CPAN but also get the same result. Right now I have DBD-mysql v3.0007 but need (v4.00) Also when I try to install open ssl it says I have the latest version. Does anyone know what I have to do to get this to work? Any help would be greatly appreciated. Thank you

  Read the article

• Apache serving empty gzip with assets produced by Rails Asset Pipeline

  - by PizzaPill

  I followed the steps described on the blogpost The Asset Pipeline, from development to production and tweaked them to my environment. The two important files are: /etc/apache/site-available/example.com <VirtualHost *:80> ServerName example.com ServerAlias www.example.com DocumentRoot "/var/www/sites/example.com/current/public" ErrorLog "/var/log/apache2/example.com-error_log" CustomLog "/var/log/apache2/example.com-access_log" common <Directory "/var/www/sites/example.com/current/public"> Options All AllowOverride All Order allow,deny Allow from all </Directory> <Directory "/var/www/sites/example.com/current/public/assets"> AllowOverride All </Directory> <LocationMatch "^/assets/.*$"> Header unset Last-Modified Header unset ETag FileETag none ExpiresActive On ExpiresDefault "access plus 1 year" </LocationMatch> RewriteEngine On # Remove the www RewriteCond %{HTTP_HOST} ^www.example.com$ [NC] RewriteRule ^(.*)$ http://example.com/$1 [R=301,L] </VirtualHost> /var/www/sites/example.com/shared/assets/.htaccess RewriteEngine on RewriteCond %{HTTP:Accept-Encoding} \b(x-)?gzip\b RewriteCond %{REQUEST_FILENAME}.gz -s RewriteRule ^(.+) $1.gz [L] <FilesMatch \.css\.gz$> ForceType text/css Header set Content-Encoding gzip </FilesMatch> <FilesMatch \.js\.gz$> ForceType text/javascript Header set Content-Encoding gzip </FilesMatch> But apache seems to send empty gzip files because the testsite looses all styles and firebug doesnt find any content for the css files. Altough if I call the assets-path directly I get some gibberish that looks like binary data. If I move the htaccess-file everything is back to normal. How could I find out where/what went wrong or do you have any suggestions what error I made? > apache2 -v System: Server version: Apache/2.2.14 (Ubuntu) Server built: Mar 5 2012 16:42:17 > uname -a Linux node0 2.6.18-028stab094.3 #1 SMP Thu Sep 22 12:47:37 MSD 2011 x86_64 GNU/Linux

  Read the article

• Plone site randomly serving wrong content

  - by Chris Miller

  I have a Plone site that has begun to randomly serve up the wrong content. Any given content suddenly shows something else. Sometimes a JPEG loads a stylesheet instead or a stylesheet loads as a page or a page as an image. The images move around, some times our site logo shows a bullet, or one of the other site images. Fiddler shows the wrong content in the response, the apache logs show the content type of the incorrect file (so if the an image loads in place of a style sheet, apache shows that). We thought mod_proxy was the source of our grief, but we get the problem hitting Zope directly. I never get the wrong content using the Medusa Monitor to repeatedly hit the content. I do see ConflictErrors in the instance.log file, and they seem to be correlated to the problem, but not 100%. ZPublisher.Conflict ConflictError at \path\to\object: database conflict error (oid 0x3586, class BTrees._OIBTree.OIBTree, serial this txn started with blah, serial currently committed blah) (X conflicts (0 unresolved) since startup blah) I pulled that off the web, it's not from our logs, but it's the same message. This may be a red herring, it sounds like those messages are normal. We've updated to the 3.3.5, same problems. I'm at a loss. I'm wondering if there a good way to intercept what is being served? Secondly, is there a way to increase the verbosity of the access log to included the content-type? I've even seen the problem manifest in ZMI. It happens more often when we're authenticated. Sometimes it can take a thousand reloads to see the problem, other times it happens in different ways every time we reload. I believe we've seen this problem for a couple years, but it was very intermittent, a page would show the content of a GIF, then a reload later wouldn't happen for a long time. Now it's a huge problem.

  Read the article

• JVM disappeared on Mac OS X Snow Leopard 10.6.8

  - by weisjohn

  I'm working in Eclipse one night, (also using Android's DDMS from the commandline). The next morning, I open the lid... attempt to run Eclipse and get an error. me$ sudo /Applications/eclipse/eclipse JavaVM: requested Java version ((null)) not available. Using Java at "" instead. JavaVM: Failed to load JVM: /bundle/Libraries/libserver.dylib So I then attempt to find out where my JDKs are pointed: me$ ls -la /System/Library/Frameworks/JavaVM.framework/Versions/ total 64 drwxr-xr-x 12 root wheel 408 Nov 16 10:44 . drwxr-xr-x 12 root wheel 408 Sep 7 09:39 .. lrwxr-xr-x 1 root wheel 5 Sep 7 17:07 1.3 -> 1.3.1 drwxr-xr-x 3 root wheel 102 Dec 2 2009 1.3.1 lrwxr-xr-x 1 root wheel 10 Sep 7 17:07 1.4 -> CurrentJDK lrwxr-xr-x 1 root wheel 10 Sep 7 17:07 1.4.2 -> CurrentJDK lrwxr-xr-x 1 root wheel 10 Sep 7 17:07 1.5 -> CurrentJDK lrwxr-xr-x 1 root wheel 10 Sep 7 17:07 1.5.0 -> CurrentJDK lrwxr-xr-x 1 root wheel 10 Sep 7 17:07 1.6 -> CurrentJDK drwxr-xr-x 9 root wheel 306 Nov 16 10:44 A lrwxr-xr-x 1 root wheel 1 Sep 7 17:07 Current -> A lrwxr-xr-x 1 root wheel 59 Sep 7 17:07 CurrentJDK -> /System/Library/Java/JavaVirtualMachines/1.6.0.jdk/Contents Everything looks normal so far... me$ ls -la /System/Library/Java/JavaVirtualMachines/ total 0 drwxr-xr-x 2 root wheel 68 Nov 16 10:44 . drwxr-xr-x 5 root wheel 170 Nov 16 10:44 .. Apparently, my virtual machines have been deleted or moved? I'll probably be able to just re-install Java, but does anyone have any insight into why this may have happened or how to prevent in the future?

  Read the article

• Installing Windows Management Framework 3.0 basically destroyed WMI, how can I fix it without reinstalling the O.S.?

  - by Massimo

  Related, of course, to this question. Before discovering it was somewhat... dangerous, I installed Windows Management Framework 3.0 on a number of Windows Server 2008 R2 SP1 servers, and WMI got completely trashed on all of them. This is what the WMI namespace looks like on a normal server (this is from Server Manager - Configuration - WMI Control): This is what it looks like after installing WMF 3.0: Yeah. Everything except WMF 3.0's new features is gone. Needless to say, nothing seems to work anymore on those servers. And no, this is not due to some strange installation error, this happened on three servers which were perfectly working before installing WMF 3.0, and on all of them the installation completed succesfully. Admittedly, one of them had a somewhat complex setup (various System Center products and SQL Server instances)... but two of them are just plain standard domain controllers which do nothing else at all. How can I fix this mess without having to reinstall the O.S. on these servers? And why did it happen in the first place?

  Read the article

• Asus K55VM usb 3.0 issue

  - by user2141481

  Good day superusers! I own the above laptop and I found out that there are some unknown and unusual issues with usb 3.0 ports. I haven't noticed anything strange until now. I got a new toshiba usb 3.0 external hdd and when I try to copy larger amount of data from my disk to the external hdd, the OS(windows 7) randomly starts ignoring the external hdd. It doesn't shut it down, it kinda just stops responding but the light on the hdd is still lit. I get an error that the files cannot be copied. I have reinstalled windows 7, installed all drivers(including intel chipset drivers of course) and the issue is still present. It acts normal when copying small amount of data. Also, I heard that some intel chipsets have an issue with usb, something about the connectors not transferring power when the usb device enters some kind of "low power mode" causing the device to stop responding and you need to plug it out and in again. But the thing is, my Intel® Chief River Chipset HM76 is not on the list of affected hardware(not ENTIRELY sure though). If anyone has any idea of what the problem to this might be, I'd be greatful. Edit: The hdd works perfectly fine even for large amounts of data if plugged in the usb 2.0 port!

  Read the article

• Computer does not boot after ram upgrade

  - by Calmarius

  I have a Dell Optiplex GX520 desktop (it's abount 5 yr old) PC with 512 MB DDR2 RAM. Since my computer always swapping I thought I should upgrade my RAM. I bought a Kingmax 2GB DDR2 RAM. But my system does not boot. The status leds are on 2 and 4. The user manual says 'video card failure' wtf? I put back the original module and everything works. I tried many combinations. When I leave the old 512 RAM in and put the 2GB next to it to the other socket my system completes the POST and I'm able to enter the BIOS menu. It says my system has 2.5 GB installed, one 0.5GB and one 2GB in dual asymmetric channel mode. It's seemingly right. Exiting the BIOS setup GRUB loads successfully, but when I try to boot Ubuntu it crashes with kernel panic immediately. Trying to load Windows XP does not get past the loading screen, it crashes with 0x8E stop error. Does this mean the ram I bought is faulty? Or is it just mean that the memory module I bought is too new to be handled my computer? I this case I may exchange the RAM with my friends. No other computer is in my house (my very old box has DDR1 ram, my systers new box has DDR3 ones. I can't plug my memory in neither one.) I'm going to return the RAM to store to replace it with a better one tomorrow. Is there any hope to get this new module work?

  Read the article

• Dell PS/2 Keyboard Stops Working Randomly After Power Disturbance

  - by Kenneth Murphy

  I have a Dell PS/2 keyboard connected to a desktop PC running Slackware 12.2 & Windows XP. After a recent, brief power outage/disturbance at my home, the keyboard has begun to quit working at random times. It has stopped at POST, but not by keyboard error -- I have to press the F1 key to continue booting, and at times the keyboard has already stopped working. Other times, the keyboard will work perfectly for a long time (a day or more) before it finally quits. It has stopped at boot, in Windows XP, and in Slackware. The led lights continue to work regardless. I have tried another PS/2 keyboard and it seems to be immune to this problem. The USB mouse always works. Does anyone have any ideas about how this might have happened? If this is related to the power disturbance that killed the power to the running PC, is it feasible that it would have only fried the keyboard itself (which still works sometimes) and not the PS/2 port nor anything else? I have experienced no other problems since the event.

  Read the article

• Apache2 VirtualHosts 403 Oddity

  - by Carson C.

  I'm sure this is something I should already understand, but I'm finding myself confused. The configs in play add up to this: NameVirtualHost *:80 Listen 80 <VirtualHost *:80> <Directory /> Options FollowSymLinks AllowOverride None Order deny,allow Deny from all </Directory> </VirtualHost> <VirtualHost *:80> ServerAdmin [email protected] ServerName domain.tld ServerAlias *.domain.tld DocumentRoot /var/www/domain.tld <Directory /var/www/domain.tld> Options -Indexes FollowSymLinks MultiViews AllowOverride None Order allow,deny Allow from all </Directory> ErrorLog ${APACHE_LOG_DIR}/error.log LogLevel warn CustomLog ${APACHE_LOG_DIR}/access.log combined </VirtualHost> DNS is working correctly. The issue is, every variant of http://*.domain.tld/ (including http://domain.tld/) works correctly, except http://www.domain.tld/ which throws a 403. The logs state: client denied by server configuration: /etc/apache2/htdocs If I remove the first VirtualHost block from play, everything works as expected including http://www.domain.tld. This leads me to believe that for some reason, Apache is not considering www.domain.tld to match the second VirtualHost block, and is thereby falling back to deny all. This seems wrong. Shouldn't the second block match www.domain.tld? I've been able to resolve this, but I still don't understand why. In my original configs, I was using the real ip address of the server instead of *. Switching all instances to * as shown above made everything work as expected. Does this have something to do with the way browsers request resources?

  Read the article

• Removing/modifying LDAP objectclasses/attributes using olc

  - by Foezjie

  I'm having trouble using openldap's olc to modify a schema without shutting down the server. To test some things out, I made the following schema: objectIdentifier tests orgUlyssisOID:4 objectIdentifier testAttribute tests:1 objectIdentifier testObjectClass tests:2 attributeType ( testAttribute:1 NAME 'attr1' DESC 'attribuut 1' SYNTAX '1.3.6.1.4.1.1466.115.121.1.40' ) attributeType ( testAttribute:2 NAME 'attr2' DESC 'attribuut 2' SUP userPassword SINGLE-VALUE ) objectclass ( testObjectClass:1 NAME 'class1' DESC 'objectclass 1' SUP top STRUCTURAL MUST (attr1 $ attr2 ) ) And added it to a new schema called test. (cn={9}test.ldif in cn=schema). Now I can't seem to figure out how to delete class1 from that schema. I use the following LDIF (and tried lots of variations too, to no avail) dn : cn={9}test,cn=schema,cn=config changetype: modify delete: olcObjectClasses olcObjectClasses: ( testObjectClass:1 NAME 'class1' DESC 'objectclass 1' SUP top STRUCTURAL MUST ( attr1 $ attr2 ) ) Running ldapmodify -x -W -D cn=admin,cn=config -f test.ldif -d 0 gives no output. -d 1 gives this: ldap_create ldap_sasl_bind ldap_send_initial_request ldap_new_connection 1 1 0 ldap_int_open_connection ldap_connect_to_host: TCP localhost:389 ldap_new_socket: 4 ldap_prepare_socket: 4 ldap_connect_to_host: Trying 127.0.0.1:389 ldap_pvt_connect: fd: 4 tm: -1 async: 0 ldap_open_defconn: successful ldap_send_server_request ber_scanf fmt ({it) ber: ber_scanf fmt ({i) ber: ber_flush2: 38 bytes to sd 4 ldap_result ld 0x7f2a8ccf3430 msgid 1 wait4msg ld 0x7f2a8ccf3430 msgid 1 (infinite timeout) wait4msg continue ld 0x7f2a8ccf3430 msgid 1 all 1 ** ld 0x7f2a8ccf3430 Connections: * host: localhost port: 389 (default) refcnt: 2 status: Connected last used: Mon Sep 10 11:29:57 2012 ** ld 0x7f2a8ccf3430 Outstanding Requests: * msgid 1, origid 1, status InProgress outstanding referrals 0, parent count 0 ld 0x7f2a8ccf3430 request count 1 (abandoned 0) ** ld 0x7f2a8ccf3430 Response Queue: Empty ld 0x7f2a8ccf3430 response count 0 ldap_chkResponseList ld 0x7f2a8ccf3430 msgid 1 all 1 ldap_chkResponseList returns ld 0x7f2a8ccf3430 NULL ldap_int_select read1msg: ld 0x7f2a8ccf3430 msgid 1 all 1 ber_get_next ber_get_next: tag 0x30 len 12 contents: read1msg: ld 0x7f2a8ccf3430 msgid 1 message type bind ber_scanf fmt ({eAA) ber: read1msg: ld 0x7f2a8ccf3430 0 new referrals read1msg: mark request completed, ld 0x7f2a8ccf3430 msgid 1 request done: ld 0x7f2a8ccf3430 msgid 1 res_errno: 0, res_error: <>, res_matched: <> ldap_free_request (origid 1, msgid 1) ldap_parse_result ber_scanf fmt ({iAA) ber: ber_scanf fmt (}) ber: ldap_msgfree ldap_free_connection 1 1 ldap_send_unbind ber_flush2: 7 bytes to sd 4 ldap_free_connection: actually freed So no real indication of an error. Where am I doing it wrong? Bonus question: If I have some entries of a certain objectclass, can I modify it (add/remove attributeTypes) without removing the entries? Thanks in advance for all help.

  Read the article

• There are currently no logon servers available

  - by Ian Robinson

  I am running a Windows 7 laptop that is joined to my company's domain. When I installed Windows 7, I created an account for myself, joined to the domain, and it had been working quite well even though I'm physically remote most of the time, and not actually on the network. However, today I created a new local user account (non-admin) for my little brother. While he was using it, he decided he wanted to install a program, because his account is not an admin, he was prompted to enter Administrator credentials to allow the program to make changes to his computer. I entered my credentials, and this is the first time I ran into the error message: There are currently no logon servers available to service the logon request. I tried logging off and loggin back in, rebooting, etc etc, and no matter what, every time I try to authenticate as my "normal" domain account - I get that message. I can no longer access my computer as an administrator. I no longer know how to log in to my machine using any other account aside from my little brother's non-admin account. I don't have any other local accounts created, and the default local admin account was never enabled. I'd appreciate any ideas on how I can recover access to my account. Let me know if I can provide any more information. FYI - This is a similar question but not sure any of the answers help me in my case. http://serverfault.com/questions/71632/there-are-currently-no-logon-servers-available-to-service-the-logon-request

  Read the article

• Can't authorize a server for Amazon RDS

  - by Parris

  We are attempting to slowly migrate a website over to AWS among other things. We decided the first thing to move was the database. We have some dedicated server with a different hosting provider. We only have one IP. I am having trouble authorizing the ip so that the old server can connect to RDS. It simply hangs for a while while using the mysql cli, then responds: ERROR 2003 (HY000): Can't connect to MySQL server on 'db.address.us-east-1.rds.amazonaws.com' (110) It did work on my laptop though. I am not quite sure what is wrong. I have a feeling I don't quite understand CIDR/IP. I simply took the ip address and tacked on /32 at the end. Then I gleaned some information that it also has to do with subnet mask? ifconfig reports: 255.255.255.0 I found a calculator and the IP changed a bit and had /24 at the end. That still didn't work. One other note... perhaps i dont know enough about the differences between OS. The hosting provider is using centOS, while our development machines are all ubuntu. Any insight would be extremely helpful! THANKS :)

  Read the article

• SQL SERVER 2005 with Windows 7 Problems

  - by azamsharp

  First of all I restored the database from other server and now all the stored procedures are named as [azamsharp].[usp_getlatestposts]. I think [azamsharp] is prefixed since it was the user on the original server. Now, on my local machine this does not run. I don't want the [azamsharp] prefix with all the stored procedures. Also, when I right click on the Sproc I cannot even see the properties option. I am running the SQL SERVER 2005 on Windows 7. UPDATE: The weird thing is that if I access the production database from my machine I can see the properties option. So, there is really something wrong with Windows 7 security. UPDATE 2: When I ran the orphan users stored procedure it showed two users "azamsharp" and "dbo1". I fixed the "azamsharp" user but "dbo1" is not getting fixed. When I run the following script: exec sp_change_users_login 'update_one', 'dbo1', 'dbo1' I get the following error: Msg 15291, Level 16, State 1, Procedure sp_change_users_login, Line 131 Terminating this procedure. The Login name 'dbo1' is absent or invalid.

  Read the article

• Deleting "undeletable" files in Vista

  - by Nik Reiman

  I recently upgraded my workstation from XP SP3 to Vista Business, and during the upgrade Windows moved my old C:\Windows directory to C:\Windows.old. I got all of the stuff I needed out of that folder, but there are six "undeletable" files there so I cannot remove it. They are: Windows.old\Program1\Adobe\Reader 9.0\Resource\CMap\Identity-H Windows.old\Program1\Adobe\Reader 9.0\Resource\CMap\Identity-V Windows.old\Program1\Common Files\Adobe\Acrobat\ActiveX\AcroIEHelper.dll Windows.old\Program1\Common Files\Adobe\Acrobat\ActiveX\AcroIEHelperShim.dll Windows.old\Program1\Common Files\Adobe\Acrobat\ActiveX\AcroPDF.dll Windows.old\Program1\Common Files\Adobe\Acrobat\ActiveX\pdfshell.dll Whenever I try to delete the files either through explorer or a command line, I get a permission denied error. I have tried to grant myself full permission on the files, but again, permission denied. I don't even have acrobat installed on my Vista machine, and I uninstalled Adobe updater. However, I still can't manage to get rid of these files. How do I nuke them for good? Edit: I was able to take ownership of the files, but I still can't delete them. Renaming them did not work, as I was denied permission to do that as well. I'll try booting up in safe mode and getting rid of them there. Edit II: Booting up into safe mode did not allow me to delete the files. Bummer.

  Read the article

• Powershell script to delete secondary SMTP addresses of Exchange 2010 Mail Contacts

  - by Zero Subnet

  I have a few thousand Exchange 2010 Mail Contacts who get erroneously assigned internal SMTP addresses by the default recipient policy. I'm trying to use the following command to delete these addresses (keeping the primary SMTP) and disabling the automatic update from recipient policy so the SMTP addresses don't get recreated again. Get-MailContact -OrganizationalUnit "domain.local/OU" -Filter {EmailAddresses -like *@domain.local -and name -notlike "ExchangeUM*"} -ResultSize unlimited -IgnoreDefaultScope | foreach {$contact = $_; $email = $contact.emailaddresses; $email | foreach {if ($_.smtpaddress -like *@domain.local) {$address = $_.smtpaddress; write-host "Removing address" $address "from Contact" $contact.name; Set-Mailcontact -Identity $contact.identity -EmailAddresses @{Remove=$address}; $contact | set-mailcontact -emailaddresspolicyenabled $false} }} I'm getting the following error though: You must provide a value expression on the right-hand side of the '-like' operator. At line:1 char:312 + Get-MailContact -OrganizationalUnit "domain.local/testou" -Filter {EmailAddresses -like "@domain.local" -and name -notlike "ExchangeUM"} -ResultSize unlimited -IgnoreDefaultScope | foreach {$contact = $; $ email = $contact.emailaddresses; $email | foreach {if ($.smtpaddress -like <<<< *@domain.local) {$address = $_.smt paddress; write-host "Removing address" $address "from Contact" $contact.name; Set-Mailcontact -Identity $contact.ident ity -EmailAddresses @{Remove=$address}; $contact }} + CategoryInfo : ParserError: (:) [], ParentContainsErrorRecordException + FullyQualifiedErrorId : ExpectedValueExpression Any help as to how to fix this?

  Read the article

• A lots of Apache processes are using my CPU uses always more than 70%

  - by Barkat Ullah

  I am running a plesk panel in 1and1. I have 120 sites running and all are using pligg cms, each site has 600 visitors per day. Please see the details of my server below: HDD-1000GB RAM-16GB Processor-6 Core I always see a lot of apache processes running in my # top view, so the server seems overloaded. If I can reduce the amount apache processes I think the server will be ok. But I don't know why too many apache processes are running. Please see the link below for the screenshot of my # top view: http://dl.dropbox.com/u/26967109/%23Top-2.jpg Sometimes I saw too many connection error in my plesk control panel, so I added the below line in my [mysqld] section: set-variable=max_connections=416 But I didn't find a solution yet. I have also added maxclients and serverlimit 416 in the config /etc/httpd/conf/httpd.conf But no solution yet. I am researching around more than 7 days but don't get any solution. Please help me to solve the problem. In peak hours my sites are taking too much time to load, but off-peak hour it is ok. Please help me to find out the actual problem.

  Read the article

• PHP cannot connect to MySQL

  - by yogal

  Hello, I recently installed Apache 2 + PHP 5.3.1 + MySQL 5.1.44 on my Windows 7 64bit machine following this guide: http://sleeplessgeek.blogspot.com/2010/01/setting-up-apache-php-mysql-phpmyadmin.html It all went fine, php is working great (even with XDebug) but I cannot connect to mysql server. A simple script I wrote to test connection (yes, root has no pass): $username = "root"; $password = ""; $database = "test"; $hostname = "localhost"; $conn = mysql_connect($hostname, $username, $password) or die("Unable to connect to MySQL Database!!"); It prints this error after 60sec of timeout: Warning: mysql_connect() [function.mysql-connect]: A connection attempt failed because the connected party did not properly respond after a period of time, or established connection failed because connected host has failed to respond. I can connect to mysql using cmdmysql -h localhost -u root Services are working properly. There also seems to be a problem with PhpMyAdmin (using 3.2.5). As soon as I type user and pass the page loads and turns blank (content-lenght in headers is 0 but status code is 302 Found). Looks like something wrong with cookies (my auth method). I hope someone has a clue, it has to be something dumb simple I missed. Thanks in advance.

  Read the article

• WinHttpCertCfg not importing certificate

  - by Ramon Zarazua

  I need to setup a deployment script that imports an SSL certificate that my service uses. I have tried importing with WinHttpCertCfg and with CertMgr to no avail. Here are the command-line arguments I have tried to use with both: winhttpcertcfg.exe -i <certname>.pfx -c LOCAL_MACHINE\My -p <password> -a <user service runs as> and CertMgr.exe -add -all -s -r localMachine -c <cert name> My It seems from what I have investigated that CertMgr does not allow you to import certificates with a password, so I'd rather get winhttpcertcfg working. When I run them I get the following output: WinHttpCertCfg: Microsoft (R) WinHTTP Certificate Configuration Tool Copyright (C) Microsoft Corporation 2001. CertMgr: CertMgr Succeeded However, when I look into the local machine certificates in MMC, try to load them from my service, or list it out through winhttpcertcfg, or even looking at the registry in HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\SystemCertificates\MY\Certificates it is not found. I have tried all of the following: If I install the cert manually (Through CertMgr.msc dialogs) it works. The user installing is running as administrator The user installing has full access on the certificate The tools print out an error when something is wrong (wrong password) Tried it in multiple machines (All of them server 2008 R2) At this point I am officially out of ideas. Thank you.

  Read the article

• Create a wifi hotspot in a place where an authentication is required

  - by SoftTimur

  I live in a residence where Internet is provided via cable. Once the computer is connected to the cable, launching a browser will trigger an authentication, I have a username and password to enter, then the internet will be connected. With a gateway (e.g. Wireless Cable Voice Gateway Model CBVG834G) and 2 cables, two PCs can connect to the Internet with my account at the same time. Now the question is, I don't like the cable, and would like to create a wifi hotspot. It seems realizable with the same gateway. According to the instruction on page 2-4 of the manual: Enter http://192.168.0.1 in the address field of your Internet browser. Log in to the gateway with either of the default user names, MSO or admin... However, while connecting to the Internet successfully via cable and the gateway (e.g. google works), opening 192.168.0.1 oddly gives me an error on the browser: Does anyone know what happened? Is it due to the authentication required by my residence? Is there any other way to build a hotspot of wifi? PS: My system is MAC OS

  Read the article

• Bad Intel DQ965GF motherboard? Fails memtest, but memory is good.

  - by Boden

  I've got a machine with a DQ965GF motherboard. Two days ago it started locking up hard. Ran memtest 3.3, 1.7, and TestMem 4. TestMem just freezes, memtest failed on moving 8 bit inversions. Letting memtest run eventually causes the system to restart. I pulled memory sticks one by one, and then replaced the memory with a couple of known good sticks. No luck. I switched power supplies, didn't help. Swapped video cards just to be safe. No help. When I start the machine I get a single beep before it POSTs. According to the manual, a single beep means: 1 beep - Refresh Error (with nothing on the screen and it is not a video problem) I'm assuming that the motherboard has failed since it's obviously not a RAM or power issue. Do you agree? NOTE: I also tried resetting BIOS defaults, and even flashed the BIOS to the latest version. I also ran the Mersenne Prime Test and the CPU seems to click along just fine. (Tried logging in to superuser with openid but it's not working for me today. Hope this gets through)

  Read the article

• Is there a tool that can test what SSL/TLS cipher suites a particular website offers?

  - by Jeremy Powell

  Is there a tool that can test what SSL/TLS cipher suites a particular website offers? I've tried openssl, but if you examine the output: $ echo -n | openssl s_client -connect www.google.com:443 CONNECTED(00000003) depth=1 /C=ZA/O=Thawte Consulting (Pty) Ltd./CN=Thawte SGC CA verify error:num=20:unable to get local issuer certificate verify return:0 --- Certificate chain 0 s:/C=US/ST=California/L=Mountain View/O=Google Inc/CN=www.google.com i:/C=ZA/O=Thawte Consulting (Pty) Ltd./CN=Thawte SGC CA 1 s:/C=ZA/O=Thawte Consulting (Pty) Ltd./CN=Thawte SGC CA i:/C=US/O=VeriSign, Inc./OU=Class 3 Public Primary Certification Authority --- Server certificate -----BEGIN CERTIFICATE----- MIIDITCCAoqgAwIBAgIQL9+89q6RUm0PmqPfQDQ+mjANBgkqhkiG9w0BAQUFADBM MQswCQYDVQQGEwJaQTElMCMGA1UEChMcVGhhd3RlIENvbnN1bHRpbmcgKFB0eSkg THRkLjEWMBQGA1UEAxMNVGhhd3RlIFNHQyBDQTAeFw0wOTEyMTgwMDAwMDBaFw0x MTEyMTgyMzU5NTlaMGgxCzAJBgNVBAYTAlVTMRMwEQYDVQQIEwpDYWxpZm9ybmlh MRYwFAYDVQQHFA1Nb3VudGFpbiBWaWV3MRMwEQYDVQQKFApHb29nbGUgSW5jMRcw FQYDVQQDFA53d3cuZ29vZ2xlLmNvbTCBnzANBgkqhkiG9w0BAQEFAAOBjQAwgYkC gYEA6PmGD5D6htffvXImttdEAoN4c9kCKO+IRTn7EOh8rqk41XXGOOsKFQebg+jN gtXj9xVoRaELGYW84u+E593y17iYwqG7tcFR39SDAqc9BkJb4SLD3muFXxzW2k6L 05vuuWciKh0R73mkszeK9P4Y/bz5RiNQl/Os/CRGK1w7t0UCAwEAAaOB5zCB5DAM BgNVHRMBAf8EAjAAMDYGA1UdHwQvMC0wK6ApoCeGJWh0dHA6Ly9jcmwudGhhd3Rl LmNvbS9UaGF3dGVTR0NDQS5jcmwwKAYDVR0lBCEwHwYIKwYBBQUHAwEGCCsGAQUF BwMCBglghkgBhvhCBAEwcgYIKwYBBQUHAQEEZjBkMCIGCCsGAQUFBzABhhZodHRw Oi8vb2NzcC50aGF3dGUuY29tMD4GCCsGAQUFBzAChjJodHRwOi8vd3d3LnRoYXd0 ZS5jb20vcmVwb3NpdG9yeS9UaGF3dGVfU0dDX0NBLmNydDANBgkqhkiG9w0BAQUF AAOBgQCfQ89bxFApsb/isJr/aiEdLRLDLE5a+RLizrmCUi3nHX4adpaQedEkUjh5 u2ONgJd8IyAPkU0Wueru9G2Jysa9zCRo1kNbzipYvzwY4OA8Ys+WAi0oR1A04Se6 z5nRUP8pJcA2NhUzUnC+MY+f6H/nEQyNv4SgQhqAibAxWEEHXw== -----END CERTIFICATE----- subject=/C=US/ST=California/L=Mountain View/O=Google Inc/CN=www.google.com issuer=/C=ZA/O=Thawte Consulting (Pty) Ltd./CN=Thawte SGC CA --- No client certificate CA names sent --- SSL handshake has read 1777 bytes and written 316 bytes --- New, TLSv1/SSLv3, Cipher is AES256-SHA Server public key is 1024 bit Compression: NONE Expansion: NONE SSL-Session: Protocol : TLSv1 Cipher : AES256-SHA Session-ID: 748E2B5FEFF9EA065DA2F04A06FBF456502F3E64DF1B4FF054F54817C473270C Session-ID-ctx: Master-Key: C4284AE7D76421F782A822B3780FA9677A726A25E1258160CA30D346D65C5F4049DA3D10A41F3FA4816DD9606197FAE5 Key-Arg : None Start Time: 1266259321 Timeout : 300 (sec) Verify return code: 20 (unable to get local issuer certificate) --- it just shows that the cipher suite is something with AES256-SHA. I know I could grep through the hex dump of the conversation, but I was hoping for something a little more elegant. I would prefer Linux tools, but Windows (or other) would be fine. This question is motivated by the security testing I do for PCI and general penetration testing. Update: GregS points out below that the SSL server picks from the cipher suites of the client. So it seems I would need to test all cipher suites one at a time. I think I can hack something together, but is there a tool that does particularly this?

  Read the article

< Previous Page | 1781 1782 1783 1784 1785 1786 1787 1788 1789 1790 1791 1792  | Next Page >