Search Results

Search found 29860 results on 1195 pages for 'write speed'.

Page 180/1195 | < Previous Page | 176 177 178 179 180 181 182 183 184 185 186 187  | Next Page >

• External USB drive is failing

  - by dma_k

  I have an external USB 2.0 drive WD My Book Mirror Edition, running in RAID 1 (mirroring) mode. A while ago the hard drive started to fail: it stops responding (directories are not listed returning an error after a big timeout). Sometimes it works for weeks before a failure, sometimes – few hours. Small write operations (like removing few files or editing a small file) do not harm, but when copying large files to the drive over the network, or creating the archive locally, the kernel dumps. Also interesting to note that once kernel has failed, Linux does not want to reboot normally (reboot hangs); when Linux box is shutdown with power button, WD drive does not go to sleep mode (as it usually does): leds continue to run, pressing and holding the "shutdown" button on drive's back panel does not do anything; only unplugging the power cord helps. Here goes the boot log: Aug 16 00:32:21 kernel: [ 1.514106] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver Aug 16 00:32:21 kernel: [ 1.657738] ehci_hcd 0000:00:1d.7: PCI INT A -> GSI 23 (level, low) -> IRQ 23 Aug 16 00:32:21 kernel: [ 1.673747] ehci_hcd 0000:00:1d.7: setting latency timer to 64 Aug 16 00:32:21 kernel: [ 1.673751] ehci_hcd 0000:00:1d.7: EHCI Host Controller Aug 16 00:32:21 kernel: [ 1.725224] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1 Aug 16 00:32:21 kernel: [ 1.741647] ehci_hcd 0000:00:1d.7: using broken periodic workaround Aug 16 00:32:21 kernel: [ 1.761790] ehci_hcd 0000:00:1d.7: cache line size of 32 is not supported Aug 16 00:32:21 kernel: [ 1.761873] ehci_hcd 0000:00:1d.7: irq 23, io mem 0xfdfff000 Aug 16 00:32:21 kernel: [ 1.796043] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00 Aug 16 00:32:21 kernel: [ 1.879069] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 Aug 16 00:32:21 kernel: [ 1.895446] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 Aug 16 00:32:21 kernel: [ 1.911796] usb usb1: Product: EHCI Host Controller Aug 16 00:32:21 kernel: [ 1.928015] usb usb1: Manufacturer: Linux 2.6.32-5-686 ehci_hcd Aug 16 00:32:21 kernel: [ 1.944331] usb usb1: SerialNumber: 0000:00:1d.7 Aug 16 00:32:21 kernel: [ 1.961285] usb usb1: configuration #1 chosen from 1 choice Aug 16 00:32:21 kernel: [ 1.994412] hub 1-0:1.0: USB hub found Aug 16 00:32:21 kernel: [ 2.010864] hub 1-0:1.0: 8 ports detected Aug 16 00:32:21 kernel: [ 2.085939] uhci_hcd: USB Universal Host Controller Interface driver Aug 16 00:32:21 kernel: [ 2.191945] uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23 Aug 16 00:32:21 kernel: [ 2.226029] uhci_hcd 0000:00:1d.0: setting latency timer to 64 Aug 16 00:32:21 kernel: [ 2.226034] uhci_hcd 0000:00:1d.0: UHCI Host Controller Aug 16 00:32:21 kernel: [ 2.243237] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2 Aug 16 00:32:21 kernel: [ 2.260390] uhci_hcd 0000:00:1d.0: irq 23, io base 0x0000fe00 Aug 16 00:32:21 kernel: [ 2.277517] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001 Aug 16 00:32:21 kernel: [ 2.294815] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 Aug 16 00:32:21 kernel: [ 2.312173] usb usb2: Product: UHCI Host Controller Aug 16 00:32:21 kernel: [ 2.329534] usb usb2: Manufacturer: Linux 2.6.32-5-686 uhci_hcd Aug 16 00:32:21 kernel: [ 2.346828] usb usb2: SerialNumber: 0000:00:1d.0 Aug 16 00:32:21 kernel: [ 2.412989] usb usb2: configuration #1 chosen from 1 choice Aug 16 00:32:21 kernel: [ 2.430651] usb 1-2: new high speed USB device using ehci_hcd and address 2 Aug 16 00:32:21 kernel: [ 2.449046] hub 2-0:1.0: USB hub found Aug 16 00:32:21 kernel: [ 2.466514] hub 2-0:1.0: 2 ports detected Aug 16 00:32:21 kernel: [ 2.484639] uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19 Aug 16 00:32:21 kernel: [ 2.537750] uhci_hcd 0000:00:1d.1: setting latency timer to 64 Aug 16 00:32:21 kernel: [ 2.537756] uhci_hcd 0000:00:1d.1: UHCI Host Controller Aug 16 00:32:21 kernel: [ 2.555085] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3 Aug 16 00:32:21 kernel: [ 2.572231] uhci_hcd 0000:00:1d.1: irq 19, io base 0x0000fd00 Aug 16 00:32:21 kernel: [ 2.589593] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001 Aug 16 00:32:21 kernel: [ 2.606869] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1 Aug 16 00:32:21 kernel: [ 2.624134] usb usb3: Product: UHCI Host Controller Aug 16 00:32:21 kernel: [ 2.641329] usb usb3: Manufacturer: Linux 2.6.32-5-686 uhci_hcd Aug 16 00:32:21 kernel: [ 2.658505] usb usb3: SerialNumber: 0000:00:1d.1 Aug 16 00:32:21 kernel: [ 2.675843] usb usb3: configuration #1 chosen from 1 choice Aug 16 00:32:21 kernel: [ 2.692864] hub 3-0:1.0: USB hub found Aug 16 00:32:21 kernel: [ 2.709651] hub 3-0:1.0: 2 ports detected Aug 16 00:32:21 kernel: [ 2.727378] uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18 Aug 16 00:32:21 kernel: [ 2.768252] uhci_hcd 0000:00:1d.2: setting latency timer to 64 Aug 16 00:32:21 kernel: [ 2.768258] uhci_hcd 0000:00:1d.2: UHCI Host Controller Aug 16 00:32:21 kernel: [ 2.806679] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4 Aug 16 00:32:21 kernel: [ 2.824117] uhci_hcd 0000:00:1d.2: irq 18, io base 0x0000fc00 Aug 16 00:32:21 kernel: [ 2.841405] usb 1-2: New USB device found, idVendor=1058, idProduct=1104 Aug 16 00:32:21 kernel: [ 2.858448] usb 1-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3 Aug 16 00:32:21 kernel: [ 2.875347] usb 1-2: Product: My Book Aug 16 00:32:21 kernel: [ 2.892113] usb 1-2: Manufacturer: Western Digital Aug 16 00:32:21 kernel: [ 2.908915] usb 1-2: SerialNumber: 575532553130303530353538 Aug 16 00:32:21 kernel: [ 2.943242] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001 Aug 16 00:32:21 kernel: [ 2.960405] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1 Aug 16 00:32:21 kernel: [ 2.977615] usb usb4: Product: UHCI Host Controller Aug 16 00:32:21 kernel: [ 2.994687] usb usb4: Manufacturer: Linux 2.6.32-5-686 uhci_hcd Aug 16 00:32:21 kernel: [ 3.011711] usb usb4: SerialNumber: 0000:00:1d.2 Aug 16 00:32:21 kernel: [ 3.029589] usb usb4: configuration #1 chosen from 1 choice Aug 16 00:32:21 kernel: [ 3.082027] sd 2:0:0:0: [sda] Attached SCSI disk Aug 16 00:32:21 kernel: [ 3.103953] usb 1-2: configuration #1 chosen from 1 choice Aug 16 00:32:21 kernel: [ 3.122625] hub 4-0:1.0: USB hub found Aug 16 00:32:21 kernel: [ 3.140484] hub 4-0:1.0: 2 ports detected Aug 16 00:32:21 kernel: [ 3.161680] uhci_hcd 0000:00:1d.3: PCI INT D -> GSI 16 (level, low) -> IRQ 16 Aug 16 00:32:21 kernel: [ 3.181257] uhci_hcd 0000:00:1d.3: setting latency timer to 64 Aug 16 00:32:21 kernel: [ 3.181263] uhci_hcd 0000:00:1d.3: UHCI Host Controller Aug 16 00:32:21 kernel: [ 3.198614] uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 5 Aug 16 00:32:21 kernel: [ 3.216012] uhci_hcd 0000:00:1d.3: irq 16, io base 0x0000fb00 Aug 16 00:32:21 kernel: [ 3.249877] Uniform CD-ROM driver Revision: 3.20 Aug 16 00:32:21 kernel: [ 3.267765] usb usb5: New USB device found, idVendor=1d6b, idProduct=0001 Aug 16 00:32:21 kernel: [ 3.284947] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1 Aug 16 00:32:21 kernel: [ 3.302023] usb usb5: Product: UHCI Host Controller Aug 16 00:32:21 kernel: [ 3.319215] usb usb5: Manufacturer: Linux 2.6.32-5-686 uhci_hcd Aug 16 00:32:21 kernel: [ 3.336298] usb usb5: SerialNumber: 0000:00:1d.3 Aug 16 00:32:21 kernel: [ 3.368377] Initializing USB Mass Storage driver... Aug 16 00:32:21 kernel: [ 3.390652] usbcore: registered new interface driver hiddev Aug 16 00:32:21 kernel: [ 3.408109] scsi4 : SCSI emulation for USB Mass Storage devices Aug 16 00:32:21 kernel: [ 3.425281] sr 0:0:1:0: Attached scsi CD-ROM sr0 Aug 16 00:32:21 kernel: [ 3.438978] sr 0:0:1:0: Attached scsi generic sg0 type 5 Aug 16 00:32:21 kernel: [ 3.456328] usbcore: registered new interface driver usb-storage Aug 16 00:32:21 kernel: [ 3.474564] usb-storage: device found at 2 Aug 16 00:32:21 kernel: [ 3.474567] usb-storage: waiting for device to settle before scanning Aug 16 00:32:21 kernel: [ 3.475320] sd 2:0:0:0: Attached scsi generic sg1 type 0 Aug 16 00:32:21 kernel: [ 3.492587] USB Mass Storage support registered. Aug 16 00:32:21 kernel: [ 3.510930] usb usb5: configuration #1 chosen from 1 choice Aug 16 00:32:21 kernel: [ 3.531076] hub 5-0:1.0: USB hub found Aug 16 00:32:21 kernel: [ 3.548399] hub 5-0:1.0: 2 ports detected Aug 16 00:32:21 kernel: [ 3.591743] input: Western Digital My Book as /devices/pci0000:00/0000:00:1d.7/usb1/1-2/1-2:1.1/input/input2 Aug 16 00:32:21 kernel: [ 3.609515] generic-usb 0003:1058:1104.0001: input,hidraw0: USB HID v1.11 Device [Western Digital My Book] on usb-0000:00:1d.7-2/input1 Aug 16 00:32:21 kernel: [ 3.627466] usbcore: registered new interface driver usbhid Aug 16 00:32:21 kernel: [ 8.581664] usb-storage: device scan complete Aug 16 00:32:21 kernel: [ 8.624270] scsi 4:0:0:0: Direct-Access WD My Book 1008 PQ: 0 ANSI: 4 Aug 16 00:32:21 kernel: [ 8.655135] scsi 4:0:0:1: Enclosure WD My Book Device 1008 PQ: 0 ANSI: 4 Aug 16 00:32:21 kernel: [ 8.675393] sd 4:0:0:0: Attached scsi generic sg2 type 0 Aug 16 00:32:21 kernel: [ 8.698669] scsi 4:0:0:1: Attached scsi generic sg3 type 13 Aug 16 00:32:21 kernel: [ 8.723370] sd 4:0:0:0: [sdb] 1953513472 512-byte logical blocks: (1.00 TB/931 GiB) Aug 16 00:32:21 kernel: [ 8.750477] sd 4:0:0:0: [sdb] Write Protect is off Aug 16 00:32:21 kernel: [ 8.769411] sd 4:0:0:0: [sdb] Mode Sense: 10 00 00 00 Aug 16 00:32:21 kernel: [ 8.769414] sd 4:0:0:0: [sdb] Assuming drive cache: write through Aug 16 00:32:21 kernel: [ 8.822971] sd 4:0:0:0: [sdb] Assuming drive cache: write through Aug 16 00:32:21 kernel: [ 8.841978] sdb: sdb1 Aug 16 00:32:21 kernel: [ 8.905580] sd 4:0:0:0: [sdb] Assuming drive cache: write through Aug 16 00:32:21 kernel: [ 8.924173] sd 4:0:0:0: [sdb] Attached SCSI disk Aug 16 00:32:21 kernel: [ 11.600492] XFS mounting filesystem sdb1 Aug 16 00:32:21 kernel: [ 12.222948] Ending clean XFS mount for filesystem: sdb1 After a while the following appears in a log: Aug 16 09:30:56 kernel: [32359.112029] usb 1-2: reset high speed USB device using ehci_hcd and address 2 Aug 16 09:31:59 kernel: [32422.112035] usb 1-2: reset high speed USB device using ehci_hcd and address 2 Aug 16 09:33:00 kernel: [32483.112029] usb 1-2: reset high speed USB device using ehci_hcd and address 2 And then it is followed by few kernel dumps, which I think, are not good: Aug 16 09:33:40 kernel: [32520.428027] INFO: task xfssyncd:1002 blocked for more than 120 seconds. Aug 16 09:33:40 kernel: [32520.462689] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. Aug 16 09:33:40 kernel: [32520.497422] xfssyncd D c3d84a60 0 1002 2 0x00000000 Aug 16 09:33:40 kernel: [32520.532117] f6c9aa80 00000046 c1132742 c3d84a60 00000286 c1418100 c1418100 00000000 Aug 16 09:33:40 kernel: [32520.566867] f6c9ac3c c2808100 00000000 f653b18b 00001d76 00000001 f6c9aa80 c3c3f0e0 Aug 16 09:33:40 kernel: [32520.601343] 08e59242 f6c9ac3c 2e41392b 00000000 08e59242 00000000 c3f7fb48 0067385a Aug 16 09:33:40 kernel: [32520.635533] Call Trace: Aug 16 09:33:40 kernel: [32520.668991] [<c1132742>] ? cfq_set_request+0x0/0x290 Aug 16 09:33:40 kernel: [32520.702804] [<c126b532>] ? io_schedule+0x5f/0x98 Aug 16 09:33:40 kernel: [32520.736555] [<c1128be0>] ? get_request_wait+0xcb/0x146 Aug 16 09:33:40 kernel: [32520.770360] [<c10437ba>] ? autoremove_wake_function+0x0/0x2d Aug 16 09:33:40 kernel: [32520.804110] [<c112907c>] ? __make_request+0x2cc/0x3d9 Aug 16 09:33:40 kernel: [32520.837713] [<c1128230>] ? blk_peek_request+0x135/0x143 Aug 16 09:33:40 kernel: [32520.871265] [<f8582987>] ? scsi_dispatch_cmd+0x185/0x1e5 [scsi_mod] Aug 16 09:33:40 kernel: [32520.904407] [<c1127cf1>] ? generic_make_request+0x266/0x2b4 Aug 16 09:33:40 kernel: [32520.937007] [<c10cf821>] ? bvec_alloc_bs+0x95/0xaf Aug 16 09:33:40 kernel: [32520.969033] [<c1127dfb>] ? submit_bio+0xbc/0xd6 Aug 16 09:33:40 kernel: [32521.000485] [<c10cffd1>] ? bio_add_page+0x28/0x2e Aug 16 09:33:40 kernel: [32521.031403] [<f8918d38>] ? _xfs_buf_ioapply+0x206/0x22b [xfs] Aug 16 09:33:40 kernel: [32521.061888] [<f89197bd>] ? xfs_buf_iorequest+0x38/0x60 [xfs] Aug 16 09:33:40 kernel: [32521.091845] [<f8907230>] ? xlog_bdstrat_cb+0x16/0x3d [xfs] Aug 16 09:33:40 kernel: [32521.121222] [<f8905781>] ? XFS_bwrite+0x32/0x64 [xfs] Aug 16 09:33:40 kernel: [32521.150007] [<f89059be>] ? xlog_sync+0x20b/0x311 [xfs] Aug 16 09:33:40 kernel: [32521.178214] [<f89112fc>] ? xfs_trans_ail_tail+0x12/0x27 [xfs] Aug 16 09:33:40 kernel: [32521.205914] [<f8906261>] ? xlog_state_sync_all+0xa2/0x141 [xfs] Aug 16 09:33:40 kernel: [32521.233074] [<f8906611>] ? _xfs_log_force+0x51/0x68 [xfs] Aug 16 09:33:40 kernel: [32521.259664] [<c103abaf>] ? process_timeout+0x0/0x5 Aug 16 09:33:40 kernel: [32521.285662] [<f8906636>] ? xfs_log_force+0xe/0x27 [xfs] Aug 16 09:33:40 kernel: [32521.311171] [<f89202df>] ? xfs_sync_worker+0x17/0x5c [xfs] Aug 16 09:33:40 kernel: [32521.336117] [<f891fbb7>] ? xfssyncd+0x134/0x17d [xfs] Aug 16 09:33:40 kernel: [32521.360498] [<f891fa83>] ? xfssyncd+0x0/0x17d [xfs] Aug 16 09:33:40 kernel: [32521.384211] [<c1043588>] ? kthread+0x61/0x66 Aug 16 09:33:40 kernel: [32521.407890] [<c1043527>] ? kthread+0x0/0x66 Aug 16 09:33:40 kernel: [32521.430876] [<c1003d47>] ? kernel_thread_helper+0x7/0x10 Aug 16 09:33:40 kernel: [32521.453394] INFO: task flush-8:16:12945 blocked for more than 120 seconds. Aug 16 09:33:40 kernel: [32521.476116] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. Aug 16 09:33:40 kernel: [32521.498579] flush-8:16 D 00000000 0 12945 2 0x00000000 Aug 16 09:33:40 kernel: [32521.520649] f4e4d540 00000046 e412e940 00000000 00000002 c1418100 c1418100 c14136ac Aug 16 09:33:40 kernel: [32521.542426] f4e4d6fc c2808100 00000000 00000000 000008b4 00000001 f4e4d540 c3c3f0e0 Aug 16 09:33:40 kernel: [32521.563745] 02e905a8 f4e4d6fc 007a5399 00000000 02e905a8 00000000 f4e2db48 00670b98 Aug 16 09:33:40 kernel: [32521.585077] Call Trace: Aug 16 09:33:40 kernel: [32521.605790] [<c126b532>] ? io_schedule+0x5f/0x98 Aug 16 09:33:40 kernel: [32521.626184] [<c1128be0>] ? get_request_wait+0xcb/0x146 Aug 16 09:33:40 kernel: [32521.646133] [<c10437ba>] ? autoremove_wake_function+0x0/0x2d Aug 16 09:33:40 kernel: [32521.665659] [<c112907c>] ? __make_request+0x2cc/0x3d9 Aug 16 09:33:40 kernel: [32521.684716] [<f891796e>] ? xfs_convert_page+0x30a/0x331 [xfs] Aug 16 09:33:40 kernel: [32521.703366] [<c1127cf1>] ? generic_make_request+0x266/0x2b4 Aug 16 09:33:40 kernel: [32521.721644] [<c10cf821>] ? bvec_alloc_bs+0x95/0xaf Aug 16 09:33:40 kernel: [32521.739465] [<c1127dfb>] ? submit_bio+0xbc/0xd6 Aug 16 09:33:40 kernel: [32521.756896] [<c10cfa45>] ? bio_alloc_bioset+0x7b/0xba Aug 16 09:33:40 kernel: [32521.774046] [<f8917af0>] ? xfs_submit_ioend_bio+0x3b/0x44 [xfs] Aug 16 09:33:40 kernel: [32521.790694] [<f8917ba3>] ? xfs_submit_ioend+0xaa/0xc4 [xfs] Aug 16 09:33:40 kernel: [32521.806736] [<f891817d>] ? xfs_page_state_convert+0x5c0/0x61c [xfs] Aug 16 09:33:40 kernel: [32521.822859] [<c113705b>] ? __lookup_tag+0x8e/0xee Aug 16 09:33:40 kernel: [32521.838958] [<f891840d>] ? xfs_vm_writepage+0x91/0xc4 [xfs] Aug 16 09:33:40 kernel: [32521.855039] [<c108bbcc>] ? __writepage+0x8/0x22 Aug 16 09:33:40 kernel: [32521.871067] [<c108c17b>] ? write_cache_pages+0x1af/0x29f Aug 16 09:33:40 kernel: [32521.886616] [<c108bbc4>] ? __writepage+0x0/0x22 Aug 16 09:33:40 kernel: [32521.901593] [<c108c285>] ? generic_writepages+0x1a/0x21 Aug 16 09:33:40 kernel: [32521.916455] [<f8918338>] ? xfs_vm_writepages+0x0/0x38 [xfs] Aug 16 09:33:40 kernel: [32521.931484] [<c108c2a5>] ? do_writepages+0x19/0x25 Aug 16 09:33:40 kernel: [32521.946648] [<c10c80d9>] ? writeback_single_inode+0xc7/0x273 Aug 16 09:33:40 kernel: [32521.961675] [<c10c8c44>] ? writeback_inodes_wb+0x3dd/0x49c Aug 16 09:33:40 kernel: [32521.976831] [<c10c8e18>] ? wb_writeback+0x115/0x178 Aug 16 09:33:40 kernel: [32521.991778] [<c10c901f>] ? wb_do_writeback+0x121/0x131 Aug 16 09:33:40 kernel: [32522.006538] [<c103abaf>] ? process_timeout+0x0/0x5 Aug 16 09:33:40 kernel: [32522.021091] [<c10c9050>] ? bdi_writeback_task+0x21/0x89 Aug 16 09:33:40 kernel: [32522.035493] [<c10979e5>] ? bdi_start_fn+0x59/0xa4 Aug 16 09:33:40 kernel: [32522.049765] [<c109798c>] ? bdi_start_fn+0x0/0xa4 Aug 16 09:33:40 kernel: [32522.063792] [<c1043588>] ? kthread+0x61/0x66 Aug 16 09:33:40 kernel: [32522.077612] [<c1043527>] ? kthread+0x0/0x66 Aug 16 09:33:40 kernel: [32522.091260] [<c1003d47>] ? kernel_thread_helper+0x7/0x10 Aug 16 09:33:40 kernel: [32522.104966] INFO: task smartctl:13098 blocked for more than 120 seconds. Aug 16 09:33:40 kernel: [32522.118883] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. Aug 16 09:33:40 kernel: [32522.133012] smartctl D 00000020 0 13098 13097 0x00000000 Aug 16 09:33:40 kernel: [32522.147221] e50b9540 00000086 c11d28a8 00000020 00000770 c1418100 c1418100 c14136ac Aug 16 09:33:40 kernel: [32522.161720] e50b96fc c2808100 00000000 e53e8800 00000000 00000020 c3cec000 c13886c0 Aug 16 09:33:40 kernel: [32522.176217] f99dab68 e50b96fc 007a4f1e 00000001 c4082f24 c4082ed8 00000001 c3c3f0e0 Aug 16 09:33:40 kernel: [32522.190737] Call Trace: Aug 16 09:33:40 kernel: [32522.205038] [<c11d28a8>] ? __netdev_alloc_skb+0x14/0x2d Aug 16 09:33:40 kernel: [32522.219605] [<c126b799>] ? schedule_timeout+0x20/0xb0 Aug 16 09:33:40 kernel: [32522.234144] [<c112820d>] ? blk_peek_request+0x112/0x143 Aug 16 09:33:40 kernel: [32522.248649] [<f85873b6>] ? scsi_request_fn+0x3c1/0x47a [scsi_mod] Aug 16 09:33:40 kernel: [32522.263233] [<c103aba8>] ? del_timer+0x55/0x5c Aug 16 09:33:40 kernel: [32522.277773] [<c126b6a2>] ? wait_for_common+0xa4/0x100 Aug 16 09:33:40 kernel: [32522.292342] [<c102cd8d>] ? default_wake_function+0x0/0x8 Aug 16 09:33:40 kernel: [32522.306958] [<c112b3d1>] ? blk_execute_rq+0x8b/0xb2 Aug 16 09:33:40 kernel: [32522.321569] [<c112b2ac>] ? blk_end_sync_rq+0x0/0x23 Aug 16 09:33:40 kernel: [32522.336070] [<c112b58b>] ? blk_recount_segments+0x13/0x20 Aug 16 09:33:40 kernel: [32522.350583] [<c1127307>] ? blk_rq_bio_prep+0x44/0x74 Aug 16 09:33:40 kernel: [32522.365059] [<c112b0b2>] ? blk_rq_map_kern+0xc5/0xee Aug 16 09:33:40 kernel: [32522.379439] [<c112e2a5>] ? sg_scsi_ioctl+0x221/0x2aa Aug 16 09:33:40 kernel: [32522.393801] [<c112e672>] ? scsi_cmd_ioctl+0x344/0x39a Aug 16 09:33:40 kernel: [32522.408140] [<c1024c87>] ? update_curr+0x106/0x1b3 Aug 16 09:33:40 kernel: [32522.422566] [<c1024c87>] ? update_curr+0x106/0x1b3 Aug 16 09:33:40 kernel: [32522.436832] [<f87676aa>] ? sd_ioctl+0x90/0xb5 [sd_mod] Aug 16 09:33:40 kernel: [32522.451228] [<c112c35f>] ? __blkdev_driver_ioctl+0x53/0x63 Aug 16 09:33:40 kernel: [32522.465689] [<c112cbbf>] ? blkdev_ioctl+0x850/0x891 Aug 16 09:33:40 kernel: [32522.479982] [<c1020474>] ? __wake_up_common+0x34/0x59 Aug 16 09:33:40 kernel: [32522.494138] [<c10244cd>] ? complete+0x28/0x36 Aug 16 09:33:40 kernel: [32522.507986] [<c1086c64>] ? find_get_page+0x1f/0x81 Aug 16 09:33:40 kernel: [32522.521671] [<c10abed5>] ? add_partial+0xe/0x40 Aug 16 09:33:40 kernel: [32522.535285] [<c1086e68>] ? lock_page+0x8/0x1d Aug 16 09:33:40 kernel: [32522.548797] [<c1087432>] ? filemap_fault+0xb5/0x2e6 Aug 16 09:33:40 kernel: [32522.562141] [<c109941c>] ? __do_fault+0x381/0x3b1 Aug 16 09:33:40 kernel: [32522.575441] [<c10d0c30>] ? block_ioctl+0x27/0x2c Aug 16 09:33:40 kernel: [32522.588708] [<c10d0c09>] ? block_ioctl+0x0/0x2c Aug 16 09:33:40 kernel: [32522.601858] [<c10bcd78>] ? vfs_ioctl+0x1c/0x5f Aug 16 09:33:40 kernel: [32522.614917] [<c10bd30c>] ? do_vfs_ioctl+0x4aa/0x4e5 Aug 16 09:33:40 kernel: [32522.627961] [<c10350db>] ? __do_softirq+0x115/0x151 Aug 16 09:33:40 kernel: [32522.640901] [<c126e270>] ? do_page_fault+0x2f1/0x307 Aug 16 09:33:40 kernel: [32522.653803] [<c10bd388>] ? sys_ioctl+0x41/0x58 Aug 16 09:33:40 kernel: [32522.666674] [<c10030fb>] ? sysenter_do_call+0x12/0x28 Then again few messages reset high speed USB device using ehci_hcd and address 2. I have browsed and read similar error reports here and there and I tried: I have upgraded the kernel from v2.6.26-2 to 2.6.32-5, which has not solved the problem. They say, this might a cable problem. I have tried to replace the USB-to-miniUSB cable (that connects external drive with computer) with another one. No changes. Somebody suggests to try another USB port. I have only 4 external USB ports, tried another one with no success. They say to try uhci_hcd. I have unmounted the device, unloaded ehci_hcd and mounted again. The difference was that now in log I get reset full speed USB device using uhci_hcd and address 2 and similar kernel dumps after a while. They say to echo 128 > /sys/block/sdb/device/max_sectors. I tried it with ehci_hcd with no success (note: I have issued this command after the drive was mounted but before using it actively). I have lauched smartmond and checking periodically the output of smartctl: drive temperature is OK, number of bad sectors and uncorrectable errors is 0. Nothing suspicious is reported by S.M.A.R.T. except maybe the following: Aug 16 12:40:12 kernel: [43715.314566] program smartctl is using a deprecated SCSI ioctl, please convert it to SG_IO Aug 16 12:40:13 kernel: [43715.705622] program smartctl is using a deprecated SCSI ioctl, please convert it to SG_IO Of course, I have not tried all combinations of above. But unfortunately, I am run out of cardinal ideas. If anybody can advice something specific about the problem, you are very welcome.

  Read the article

• How to Loop through LINQ results (VB.NET)

  - by rockinthesixstring

  I've got some code to try and loop through LINQ results, but it doesn't seem to be working. HERE'S THE CODE Public Sub ProcessRequest(ByVal context As System.Web.HttpContext) Implements System.Web.IHttpHandler.ProcessRequest ' the page contenttype is plain text' HttpContext.Current.Response.ContentType = "text/plain" ' store the querystring as a variable' Dim qs As Nullable(Of Integer) = Integer.TryParse(HttpContext.Current.Request.QueryString("ID"), Nothing) ' use the RegionsDataContext' Using RegionDC As New DAL.RegionsDataContext 'create a (q)uery variable' Dim q As Object ' if the querystring PID is not blank' ' then we want to return results based on the PID' If Not qs Is Nothing Then ' that fit within the Parent ID' q = (From r In RegionDC.bt_Regions _ Where r.PID = qs _ Select r.Region).ToArray ' now we loop through the array' ' and write out the ressults' For Each item As DAL.bt_Region In q HttpContext.Current.Response.Write(item.Region & vbCrLf) Next End If End Using End Sub HERE'S THE ERROR Public member 'Region' on type 'String' not found. Description: An unhandled exception occurred during the execution of the current web request. Please review the stack trace for more information about the error and where it originated in the code. Exception Details: System.MissingMemberException: Public member 'Region' on type 'String' not found. Source Error: Line 33: ' and write out the ressults Line 34: For Each item In q Line 35: HttpContext.Current.Response.Write(item.Region & vbCrLf) Line 36: Next Line 37: Source File: E:\Projects\businesstrader\App_Code\Handlers\RegionsAutoComplete.vb Line: 35 Stack Trace: [MissingMemberException: Public member 'Region' on type 'String' not found.] Microsoft.VisualBasic.CompilerServices.Container.GetMembers(String& MemberName, Boolean ReportErrors) +509081 Microsoft.VisualBasic.CompilerServices.NewLateBinding.LateGet(Object Instance, Type Type, String MemberName, Object[] Arguments, String[] ArgumentNames, Type[] TypeArguments, Boolean[] CopyBack) +222 BT.Handlers.RegionsAutoComplete.ProcessRequest(HttpContext context) in E:\Projects\businesstrader\App_Code\Handlers\RegionsAutoComplete.vb:35 System.Web.CallHandlerExecutionStep.System.Web.HttpApplication.IExecutionStep.Execute() +181 System.Web.HttpApplication.ExecuteStep(IExecutionStep step, Boolean& completedSynchronously) +75 Can anyone tell me what I'm doing wrong?

  Read the article

• port forwarding? [closed]

  - by Nrew

  Possible Duplicate: Configure Modem for Bittorrent downloads any guides on portforwarding? I want to speed up my torrent downloads

  Read the article

• DDR3 10600 memory running at 533mhz

  - by Elger

  I bought a second hand hp dl160 g6 a year ago with 48GB configured in it. I discovered checking with cpu-z and doublechecked with speccy the memory runs at only 533Mhz. I checked the configuration with the HP memory configurator and the banks are populated correctly for max performance. There are 12 banks populated with micron and hynix memory of 4gb, all capable of running 1333mhz. What could me wrong here? C:\Users\Administrator>wmic Memorychip get manufacturer, partnumber, speed, seri alnumber, devicelocator, banklabel BankLabel DeviceLocator Manufacturer PartNumber SerialNumber Speed BANK0 PROC 1 DIMM 3A Micron 36JSZF51272PZ1G4F C5DF65D7 1333 BANK1 PROC 1 DIMM 2D Micron 36JSZF51272PY1G4D 951565E0 1333 BANK3 PROC 1 DIMM 6B Micron 36JSZF51272PZ1G4F 3F3160D6 1333 BANK4 PROC 1 DIMM 5E Hyundai HMT151R7BFR4C-H9 E28A3014 1333 BANK6 PROC 1 DIMM 9C Micron 36JSZF51272PZ1G4F 26DF7E1A 1333 BANK7 PROC 1 DIMM 8F Micron 36JSZF51272PZ1G4G 77FC67D7 1333 BANK9 PROC 2 DIMM 3A Hyundai HMT151R7BFR4C-H9 FB763433 1333 BANK10 PROC 2 DIMM 2D Hyundai HMT151R7BFR4C-H9 E18AA014 1333 BANK12 PROC 2 DIMM 6B Hyundai HMT151R7BFR4C-H9 DF8A1014 1333 BANK13 PROC 2 DIMM 5E Hyundai HMT151R7BFR4C-H9 6968511A 1333 BANK15 PROC 2 DIMM 9C Hyundai HMT151R7BFR4C-H9 F28A7014 1333 BANK16 PROC 2 DIMM 8F Micron 36JSZF51272PZ1G4G 76FC67D7 1333

  Read the article

• Load Average runaway

  - by mewrei

  Is there any way to chase down lockups and runaway load averages? Every so often (pretty randomly) I'll get my load average spike up over 5 usually to around 10-15 and sometimes as high as 75 (dual core machine), and cause my system to lock for an indeterminate amount of time. The only thing I can possibly chase it to is using nVidia fakeraid (RAID-1) with JFS on top of that for my /home partition. Also I noticed that when my load averages spike, the power management system doesn't step up my processor speed from 1.6 to its maximum 2.13Ghz clock speed (not sure if this makes a huge difference with this problem). Any ideas?

  Read the article

• Packet loss rate with iperf and tcpdump

  - by stefita

  I tested a line for its link quality with iperf. The measured speed (UDP port 9005) was 96Mbps, which is fine, because both servers are connected with 100Mbps to the internet. On the other hand the datagram loss rate was shown to be 3.3-3.7%, which I found a little too much. Using a high-speed transfer protocol I recorded the packets on both sides with tcpdump. Than I calculated the packet loss - average 0.25%. Have anyone an explanation, where this big difference may be coming from? What is an acceptable packet loss in your opinion?

  Read the article

• Indy 10 - IdSMTP.Send() hangs when sending messages from GMail account

  - by LukLed

  I am trying to send an e-mail using gmail account (Delphi 7, Indy 10) with these settings: TIdSmtp: Port = 587; UseTLS := utUseExplicitTLS; TIdSSLIOHandlerSocketOpenSSL: SSLOptions.Method := sslvTLSv1; Everything seems to be set ok. I get this response: Resolving hostname smtp.gmail.com. Connecting to 74.125.77.109. SSL status: "before/connect initialization" SSL status: "before/connect initialization" SSL status: "SSLv3 write client hello A" SSL status: "SSLv3 read server hello A" SSL status: "SSLv3 read server certificate A" SSL status: "SSLv3 read server done A" SSL status: "SSLv3 write client key exchange A" SSL status: "SSLv3 write change cipher spec A" SSL status: "SSLv3 write finished A" SSL status: "SSLv3 flush data" SSL status: "SSLv3 read finished A" SSL status: "SSL negotiation finished successfully" SSL status: "SSL negotiation finished successfully" Cipher: name = RC4-MD5; description = RC4-MD5 SSLv3 Kx=RSA Au=RSA Enc=RC4(128) Mac=MD5 ; bits = 128; version = TLSv1/SSLv3; And then it hangs and doesn't finish. E-mail is not sent. What can be the problem?

  Read the article

• Command-line: What is this machine ?

  - by lindenb

  Hi all, is there a standard command-line for linux answering a description of the server (model, number of cores(?), speed(?)...)? Thanks, Pierre

  Read the article

• ASP Classic page quit working

  - by justSteve

  I've had a set of legacy pages running on my IIS7 server for at least a year. Sometime last week something changed and now this line: Response.Write CStr(myRS(0).name) & "=" & Cstr(myRS(0).value) which used to return nothing more exciting than the string: 'Updated=true' (the sproc processing input params, stores them to a table, checks for errors and when that's all done returns a success code by executing this statement: select 'true' as [Updated] Now my pageside error handler is being involved and offers: myError=Error from /logQuizScore.asp Error source: Microsoft VBScript runtime error Error number: 13 Error description: Type mismatch Important to note that all lots of pages use the same framework - same db, same coding format, connecitonstrings and (so far as I can tell) all others are working. Troubleshot to this point: The call to the stored procedure is working correctly (stuff is stored to the given table). The output from the stored procedure is working correctly (i can execute a direct call with the given parameters and stuff works. I can see profiler calling and passing. I can replace all code with 'select 'true' as updated' and the error is the same. everything up to the response.write statement above is correct. So something changed how ADO renders that particular recordset. So i try: Response.Write myRS.Item.count and get: Error number: 424 Error description: Object required The recordset object seems not to be instantiating but the command object _did execute. Repeat - lots of other pages just the same basic logic to hit other sprocs without a problem. full code snippet set cmd1 = Server.CreateObject("ADODB.Command") cmd1.ActiveConnection = MM_cnCompliance4_STRING cmd1.CommandText = "dbo._usp_UserAnswers_INSERT" ... cmd1.CommandType = 4 cmd1.CommandTimeout = 0 cmd1.Prepared = true set myRS = cmd1.Execute Response.Write CStr(myRS(0).name) & "=" & Cstr(myRS(0).value)

  Read the article

• How to Process Lambda Expressions Passed as Argument Into Method - C# .NET 3.5

  - by Sunday Ironfoot

  My knowledge of Lambda expressions is a bit shaky, while I can write code that uses Lambda expressions (aka LINQ), I'm trying to write my own method that takes a few arguments that are of type Lambda Expression. Background: I'm trying to write a method that returns a Tree Collection of objects of type TreeItem from literally ANY other object type. I have the following so far: public class TreeItem { public string Id { get; set; } public string Text { get; set; } public TreeItem Parent { get; protected set; } public IList<TreeItem> Children { get { // Implementation that returns custom TreeItemCollection type } } public static IList<TreeItem> GetTreeFromObject<T>(IList<T> items, Expression<Func<T, string>> id, Expression<Func<T, string>> text, Expression<Func<T, IList<T>>> childProperty) where T : class { foreach (T item in items) { // Errrm!?? What do I do now? } return null; } } ...which can be called via... IList<TreeItem> treeItems = TreeItem.GetTreeFromObject<Category>( categories, c => c.Id, c => c.Name, c => c.ChildCategories); I could replace the Expressions with string values, and just use reflection, but I'm trying to avoid this as I want to make it strongly typed. My reasons for doing this is that I have a control that accepts a List of type TreeItem, whereas I have dozens of different types that are all in a tree like structure, and don't want to write seperate conversion methods for each type (trying to adhere to the DRY principle). Am I going about this the right way? Is there a better way of doing this perhaps?

  Read the article

• Is my PC Good enough [closed]

  - by Moinak Nath

  I'm getting a new laptop this Christmas and I was wondering if it's good enough for what I do. I'll be playing games like Need for Speed: Most Wanted (2012) and other NFS games. Also silent hunter and flight sim. I also browse the internet download stuff like, watch movies occasionally type documents with word, edit videos, and transfer files. To be more specific is the hdd big enough? is the ram big enough? Is the graphics card good? is the cpu speed enough, and is Windows windows 8 good for all these things. i also video chat so these are the specs 2.2 Ghz Intel Pentium B960 Dual Core 4 GB RAM 320 GB HDD Intel HD Graphics 720p Webcam 4 USB Ports (2 USB 3.0 @ 2 USB 2.0) HDMI Port It Is a Lenovo IdeaPad This is the one im Looking at http://www.bestbuy.com/site/Lenovo+-+IdeaPad+15.6%26%2334%3B+Laptop+-+4GB+Memory+-+320GB+Hard+Drive+-+Black/6851264.p?id=1218809260330&skuId=6851264#tab=specifications

  Read the article

• How to find cause and of the SocketException with message that an established connection was aborted

  - by cdpnet

  Hi All, I know the similar question may have been asked many times, but I want to represent the behavior I'm seeing and find if somebody can help predict the cause of this. I am writing a windows service which connects to other windows service over TCP. There are 100 user entities of this, and 5 connections per each. These users perform their tasks using their individual connections. The application goes on withough seeing this problem for 1 or 2 days. Or sometimes show the problem right after starting (-rarely). The best run I had was like 4 to 5 days without showing this exception. And after that application died or I had to stop it for various reasons. I want to know what can be causing this? Here is the stacktrace. System.IO.IOException: Unable to write data to the transport connection: An established connection was aborted by the software in your host machine. ---> System.Net.Sockets.SocketException: An established connection was aborted by the software in your host machine at System.Net.Sockets.Socket.Send(Byte[] buffer, Int32 offset, Int32 size, SocketFlags socketFlags) at System.Net.Sockets.NetworkStream.Write(Byte[] buffer, Int32 offset, Int32 size) --- End of inner exception stack trace --- at System.Net.Sockets.NetworkStream.Write(Byte[] buffer, Int32 offset, Int32 size) at System.Net.Security._SslStream.StartWriting(Byte[] buffer, Int32 offset, Int32 count, AsyncProtocolRequest asyncRequest) at System.Net.Security._SslStream.ProcessWrite(Byte[] buffer, Int32 offset, Int32 count, AsyncProtocolRequest asyncRequest) at System.Net.Security.SslStream.Write(Byte[] buffer, Int32 offset, Int32 count)

  Read the article

• SMO restore of SQL database doesn't overwrite

  - by Tom H.

  I'm trying to restore a database from a backup file using SMO. If the database does not already exist then it works fine. However, if the database already exists then I get no errors, but the database is not overwritten. The "restore" process still takes just as long, so it looks like it's working and doing a restore, but in the end the database has not changed. I'm doing this in Powershell using SMO. The code is a bit long, but I've included it below. You'll notice that I do set $restore.ReplaceDatabase = $true. Also, I use a try-catch block and report on any errors (I hope), but none are returned. Any obvious mistakes? Is it possible that I'm not reporting some error and it's being hidden from me? Thanks for any help or advice that you can give! function Invoke-SqlRestore { param( [string]$backup_file_name, [string]$server_name, [string]$database_name, [switch]$norecovery=$false ) # Get a new connection to the server [Microsoft.SqlServer.Management.Smo.Server]$server = New-SMOconnection -server_name $server_name Write-Host "Starting restore to $database_name on $server_name." Try { $backup_device = New-Object("Microsoft.SqlServer.Management.Smo.BackupDeviceItem") ($backup_file_name, "File") # Get local paths to the Database and Log file locations If ($server.Settings.DefaultFile.Length -eq 0) {$database_path = $server.Information.MasterDBPath } Else { $database_path = $server.Settings.DefaultFile} If ($server.Settings.DefaultLog.Length -eq 0 ) {$database_log_path = $server.Information.MasterDBLogPath } Else { $database_log_path = $server.Settings.DefaultLog} # Load up the Restore object settings $restore = New-Object Microsoft.SqlServer.Management.Smo.Restore $restore.Action = 'Database' $restore.Database = $database_name $restore.ReplaceDatabase = $true if ($norecovery.IsPresent) { $restore.NoRecovery = $true } Else { $restore.Norecovery = $false } $restore.Devices.Add($backup_device) # Get information from the backup file $restore_details = $restore.ReadBackupHeader($server) $data_files = $restore.ReadFileList($server) # Restore all backup files ForEach ($data_row in $data_files) { $logical_name = $data_row.LogicalName $physical_name = Get-FileName -path $data_row.PhysicalName $restore_data = New-Object("Microsoft.SqlServer.Management.Smo.RelocateFile") $restore_data.LogicalFileName = $logical_name if ($data_row.Type -eq "D") { # Restore Data file $restore_data.PhysicalFileName = $database_path + "\" + $physical_name } Else { # Restore Log file $restore_data.PhysicalFileName = $database_log_path + "\" + $physical_name } [Void]$restore.RelocateFiles.Add($restore_data) } $restore.SqlRestore($server) # If there are two files, assume the next is a Log if ($restore_details.Rows.Count -gt 1) { $restore.Action = [Microsoft.SqlServer.Management.Smo.RestoreActionType]::Log $restore.FileNumber = 2 $restore.SqlRestore($server) } } Catch { $ex = $_.Exception Write-Output $ex.message $ex = $ex.InnerException while ($ex.InnerException) { Write-Output $ex.InnerException.message $ex = $ex.InnerException } Throw $ex } Finally { $server.ConnectionContext.Disconnect() } Write-Host "Restore ended without any errors." }

  Read the article

• For what sort of workload can a Core i7-920 be faster than a i7-860?

  - by netvope

  Core i7-860 has a slightly higher clock speed (2.8 vs 2.66 GHz) Core i7-920 has QPI and tri-channel DDR3 (vs DMI and dual-channel)

  Read the article

• jQuery document.ready + Asp.Net ContentPlaceholder cause Visual Studio intellisence problems

  - by Konstantin

  Hi! I want to execute JavaScript when document is ready without much syntax overhead. The idea is to use Site.Master and ContentPlaceholder: <script type="text/javascript"> $(document).ready(function () { <asp:ContentPlaceHolder ID="OnReadyScript" runat="server" /> }); </script> and in inherited pages just write plain code: <asp:Content ID="Content3" ContentPlaceHolderID="OnReadyScript" runat="server"> $("#Login").focus(); </asp:Content> It works fine but Visual Studio complains and gives warnings. Warning in master page is Expected expression at the line <asp:ContentPlaceHolder. In inherited pages warning is Could not find 'OnReadyScript' in the current master page or pages. I tried using Writer.Write in master page to render script tag and wrapping code: <% Writer.Write(@"<script type=""text/javascript"">$(document).ready(function () {"); %> <asp:ContentPlaceHolder ID="OnReadyScrit" runat="server" /> <% Writer.Write(@"});"); %> but page rendering terminates after opening script tag is rendered. Html basically ends with <script type="text/javascript"> How can I make it work?

  Read the article

• Java / Groovy Socket - Detecting the socket being closed in a non-blocking way

  - by John Arrowwood

  I'm trying to create a small HTTP proxy that can re-write the request/headers as needed to suit my requirements. If one already exists, please, point me to it. Otherwise... I've written something that ALMOST works. It can do the proxy function, but not the re-write (yet). Problem is, I can't detect when the remote socket has been closed down without doing a blocking read. It is CRITICAL for the functionality of this thing that it be able to detect the socket being closed without blocking. I have SCOURED the Java API documentation, and I can't find ANY indication that it is even possible. Here's what I have: while ( this.inbound.isConnected() && this.outbound.isConnected() ) { try { while ( ( available = readFromClient.available() ) != 0 ) { if ( available > 1024 ) available = 1024 bytesRead = readFromClient.read( buffer, 0, available ) writeToServer.write( buffer, 0, bytesRead ) } while ( ( available = readFromServer.available() ) != 0 ) { if ( available > 1024 ) available = 1024 bytesRead = readFromServer.read( buffer, 0, available ) writeToClient.write( buffer, 0, bytesRead ) } } catch (e) { print e } println "Connected: " + this.inbound.isConnected() println "Bound: " + this.inbound.isBound() println "InputShutdown: " + this.inbound.isInputShutdown() println "OutputShutdown: " + this.inbound.isOutputShutdown() print "\n"; Thread.sleep( 10 ) } The tests for the socket being closed never indicate that the socket was closed. And, as I mentioned, I can't find ANY examples of how to detect the 'END OF FILE' condition on the stream without doing a blocking read. There HAS to be a way. Does anyone here know what it is?

  Read the article

• SWI-Prolog as an embedded application in VS2008 C++

  - by H.J. Miri

  I have a C++ application (prog.sln) which is my main program and I want to use Prolog as an embedded logic server (hanoi.pl) int main(int argc, char** argv) { putenv( "SWI_HOME_DIR=C:\\Program Files\\pl" ); argv[0] = "libpl.dll"; argv[1] = "-x"; argv[2] = "hanoi.pl"; argv[3] = NULL; PL_initialise(argc, argv); { fid_t fid = PL_open_foreign_frame(); predicate_t pred = PL_predicate( "hanoi", 1, "user" ); int rval = PL_call_predicate( NULL, PL_Q_NORMAL, pred, 3 ); qid_t qid = PL_open_query( NULL, PL_Q_NORMAL, pred, 3 ); while ( PL_next_solution(qid) ) return qid; PL_close_query(qid); PL_close_foreign_frame(fid); system("PAUSE"); } return 1; system("PAUSE"); } Here is my Prolog source code: :- use_module( library(shlib) ). hanoi( N ):- move( N, left, center, right ). move( 0, _, _, _ ):- !. move( N, A, B, C ):- M is N-1, move( M, A, C, B ), inform( A, B ), move( M, C, B, A ). inform( X, Y ):- write( 'move a disk from ' ), write( X ), write( ' to ' ), write( Y ), nl. I type at the command: plld -o hanoi prog.sln hanoi.pl But it doesn't compile. When I run my C++ app, it says: Undefined procedure: hanoi/1 What is missing/wrong in my code or at the prompt that prevents my C++ app from consulting Prolog? Appreciate any help/pointer.

  Read the article

• Understanding WordProcessingML tags and avoid unnecessary tags

  - by rithanyalaxmi

  Hi, I am using MS Word API to generate .docx which contains the data fetched from DB, in which i am applying the respective styles, fonts, symbols, etc. If the data fetched from the DB is quite huge, then there is a problem in displaying those data in the .docx file. I found that internally MS Word 2007 will write some content through tags which may not be needed to display the data. Hence i am figuring out what are the necessary MS Word tags needed when converting into a .xml file. So that i can avoid unnecessary tags and build only the respective tags which are needed to display the data. Hence i am planning to write my own .xml with the MS Word tags which are needed, than generating a .XML from .docx file My queries are:- 1) Whether it is right that the MS Word will generate some tags which may not be needed during the conversion of .docx to document.xml? That makes it heavy? If so what are the tags , so that i can avoid them when write by own .xml file. 2) Please send links to understand about the MS Word tags and its advantages, which tags are needed and which are not ? 3) Whether my approach to write a new .xml similar to document.xml (.docx conversion) is worthy one to go forward so that i can build the .xml with the tags i needed , so that i can improve the performance of the data display? Please shed some light into it and thanks in advance.. Thanks, Rithu

  Read the article

• How does one calculate voltages for overclocking?

  - by TardisGuy

  So, all I know is voltage and clock have something to do with each other. Unstable if too low voltage Too high voltage, and too much heat. or higher voltage + lower clock may heat less than that voltage at higher clock. The reason why im asking is because if I can learn how the power vs speed works, Then i might be able to project some kind of thermal curve to find out where my perfect overclock might be (without 50 burn-ins) But, as is apparent im sure. I have no idea what im talking about. If anyone can help me learn more about this; throw me a page, a macro, whathaveyou I will bow before your awesomeness and... Mail you a phantom hand written thank you letter. Some clarification Rev 1 What im trying to learn: is how much power a cpu is using with measurements (Core Voltage) vs (Clock speed) - It would answer the question: Would a 1.4v core @ 4.0Ghz use as much power as a 1.4v core @ 3.0Ghz?

  Read the article

• What is the recommended coding style for PowerShell?

  - by stej

  Is there any recommended coding style how to write PowerShell scripts? It's not about how to structure the code (how many functions, if to use module, ...). It's about 'how to write the code so that it is readable'. In programming languages there are some recommended coding styles (what to indent, how to indent - spaces/tabs, where to make new line, where to put braces,...), but I haven't seen any suggestion for PowerShell. What I'm interested particularly in: How to write parameters function New-XYZItem ( [string] $ItemName , [scriptblock] $definition ) { ... (I see that it's more like 'V1' syntax) or function New-PSClass { param([string] $ClassName ,[scriptblock] $definition )... or (why to add empty attribute?) function New-PSClass { param([Parameter()][string] $ClassName ,[Parameter()][scriptblock] $definition )... or (other formatting I saw maybe in Jaykul's code) function New-PSClass { param( [Parameter()] [string] $ClassName , [Parameter()] [scriptblock] $definition )... or ..? How to write complex pipeline Get-SomeData -param1 abc -param2 xyz | % { $temp1 = $_ 1..100 | % { Process-somehow $temp1 $_ } } | % { Process-Again $_ } | Sort-Object -desc or (name of cmdlet on new line) Get-SomeData -param1 abc -param2 xyz | % { $temp1 = $_ 1..100 | % { Process-somehow $temp1 $_ } } | % { Process-Again $_ } | Sort-Object -desc | and what if there are -begin -process -end params? how to make it the most readable? Get-SomeData -param1 abc -param2 xyz | % -begin { init } -process { Process-somehow2 ... } -end { Process-somehow3 ... } | % -begin { } .... or Get-SomeData -param1 abc -param2 xyz | % ` -begin { init } ` -process { Process-somehow2 ... } ` -end { Process-somehow3 ... } | % -begin { } .... the indentitation is important here and what element is put on new line as well. I have covered only questions that come on my mind very frequently. There are some others, but I'd like to keep this SO question 'short'. Any other suggestions are welcome.

  Read the article

• mnesia primary key

  - by maryjanne

  Hi I have two tables one notes and one tag and I want to make the id from notes primary key to use it in the tag table, but I don't know where I do wrong. My notes id is generate from another table counter, with the function dirty_update_counter. My function for the id_notes from tag looks like this: Fun = fun() -> mnesia:write(#tag{ id_note =0}) end, mnesia:transaction(Fun). generate_Oid(TableName) when is_atom(TableName) -> F = fun() -> [Oid] = mnesia:read(tag, TableName, write), NewId = Oid#tag.id_note+1, New = Oid#tag{id_note = NewId}, mnesia:write(New), NewId end, mnesia:transaction(F). insert_n(N) when is_record(N, note) -> F = fun() -> {atomic, Id} = generate_Oid(note), New = N#note{id = Id}, mnesia:write(New), New end, mnesia:transaction(F). find_n(Id) when is_integer(Id) -> {atomic, [N]} = mnesia:transaction(fun() -> mnesia:read({note, Id}) end), N. But this function don't increment my field id_note from the table tag, despite the fact that in my note table, my id field is incremented from counter table. Thanks in advance for any help.

  Read the article

• PLT Scheme Memory

  - by Eric

  So I need some help with implementing a Make-memory program using Scheme. I need two messages 'write and 'read. So it would be like (mymem 'write 34 -116) and (mymem 'read 99) right? and (define mymem (make-memory 100)).....How would I implement this in scheme? using an Alist???I need some help coding it. I have this code which makes make-memory a procedure and when you run mymem you get ((99.0)) and what i need to do is recur this so i get an alist with dotted pairs to ((0.0)). So any suggestions on how to code this?? Does anyone have any ideas what I could do to recur and make messages Write and read?? (define make-memory (lambda (n) (letrec ((mem '()) (dump (display mem))) (lambda () (if (= n 0) (cons (cons n 0) mem) mem) (cons (cons (- n 1) 0) mem)) (lambda (msg loc val) (cond ((equal? msg 'read) (display (cons n val))(set! n (- n 1))) ((equal? msg 'write) (set! mem (cons val loc)) (set! n (- n 1)) (display mem))))))) (define mymem (make-memory 100)) Yes this is an assignment but I wrote this code. I just need some help or direction. And yes I do know about variable-length argument lists.

  Read the article

• Should I use 802.11n with a 15 Mbps ISP (Comcast Cable)?

  - by stackoverflowuser2010

  I currently own a LinkSys-WRT54GL 802.11a/b/g wireless router, and my ISP is Comcast Cable providing me with 15 Mbps (that's bits per second, I believe) download speed. I am wondering if there is any benefit with using an 802.11n wireless router to access the Internet? The maximum theoretical speed of the WRT54GL router is 54 Mbps (802.11g), which is faster than the 15 Mbps provided by my ISP. I know that 802.11n has a max bandwidth of 300 Mbps, and it would help for intra-house transfers, such as streaming video from one computer to another. But is there any benefit to 802.11n for Internet activity, such as web browswing, gaming, and streaming video from Netflix?

  Read the article

• how to escape “@” in the username when logging in through FTPES with curl?

  - by user62367

  $ curl -T "index.html" -k --ftp-ssl -u "[email protected]" MYDOMAIN.COM Enter host password for user '[email protected]': % Total % Received % Xferd Average Speed Time Time Time Current Dload Upload Total Spent Left Speed 0 57173 0 0 0 0 0 0 --:--:-- 0:00:01 --:--:-- 0 <!DOCTYPE HTML PUBLIC "-//IETF//DTD HTML 2.0//EN"> <html><head> <title>405 Method Not Allowed</title> </head><body> <h1>Method Not Allowed</h1> <p>The requested method PUT is not allowed for the URL /index.html.</p> <hr> <address>Apache/2.2.16 Server at MYDOMAIN.COM Port 80</address> </body></html> 100 57480 100 307 100 57173 284 52902 0:00:01 0:00:01 --:--:-- 53633 can someone help me? Also posted on Stack Overflow

  Read the article

• Open source Distributed computing tool

  - by Prasenjit Chatterjee

  I want to set up distributed computing on my Local Area Network consisting a bunch of PCs. Say for the time being each one has the same OS - Windows 7. Is there any opensource tool available so that I can share the resources of these PCs over the LAN and increase the speed of my applications and the memory space. I know that if its a graphics intensive application then, it is not very practical, because the speed of LAN is much slower than Graphics processors. But I only want to share general applications, some basic softwares, Programming language IDEs etc. Can anyone shed some light on it? Thanks in Advance..

  Read the article

< Previous Page | 176 177 178 179 180 181 182 183 184 185 186 187  | Next Page >