Search Results

Search found 7742 results on 310 pages for 'continuous learning'.

Page 182/310 | < Previous Page | 178 179 180 181 182 183 184 185 186 187 188 189  | Next Page >

• Failure to obtain IP with ARP over Wi-Fi with personal Wi-Fi router in client mode

  - by axk

  I'm trying to connect a Samsung TV to the Internet using a TL-MR3020 personal wireless router in client mode. The TV fails to connect to the network. It sees the ethernet cable connected though. Here's my network topology: Here's what I've captured with Wireshark filtering for ARP (eth.type == 0x0806): It appears the TV fails to get the IP of the gateway (DSL modem/router) for some reason. One thing I've noticed is that the source MAC for the ARP requests coming from the TV is the MAC of the Portable wireless router (that is cd:89:00), not the TV itself and the modem sends the responses to that MAC (I'm not an expert and don't know if its okay or it may make the TV fail to get the requested IP). Also I'm able to ping the TV from the DSL router (through the telnet interface) and the router has an entry in its MAC table for the TV's IP with the Portable wireless router's MAC (that is cd:89:00). If I'm able to ping the TV I suppose it should know the router's MAC to respond to the ping, but then why these continuous ARP requests... I've also tried to connect my desktop trough this Portable wireless router the same way I'm trying to connect the TV and it works fine, I can set the DSL Modem's IP as the default gateway on the desktop's NIC and connect to the Internet. The TV can connect to the Internet when connected to the DSL Router with a wired connection. Any suggestions on what may be the cause of the problem / how to further debug it are welcome. Thanks!

  Read the article

• Anyway to backup nginx before recompiling

  - by JM4

  I am looking to install the HttpGeoipModule for NGINX but learning I have to recompile the entire thing from source in order to do so. I have a new Media Temple DV 4.0 server and that comes with nginx v 1.3.0 stock and have never had to recompile from source before and a bit nervous to make changes without being able to revert to a previous state in the event something messes up (that and the fact it is affecting a live server so no idea what downtime is). My plan was to copy all the existing modules used (nginx -V to list them all and copy the modules already compiled). Then rebuild from source with the copied info above and including the ./configure --with-http_geoip_module reference. Is is possible to backup the existing nginx configuration in the event something goes wrong?

  Read the article

• CC.NET + SVN : Server certificate issue

  - by MSI

  I am trying to setup Continuous Integration in our office. Being a puny little developer I am facing this supposedly infamous problem: " Source control operation failed: svn: OPTIONS of 'https://trunkURL': Server certificate verification failed: issuer is not trusted" So I tried the following solution - Run CC.NET service (server running as win service) using a domain account (rather than default LOCAL SYSTEMS) and accept cert permanently using command prompt under that user by using svn log/list on the repo. Doesn't help :(. I am getting the following from my artifact/log files(or dashboard) ThoughtWorks.CruiseControl.Core.CruiseControlException: Source control operation failed: svn: OPTIONS of 'https://TrunkURL': Server certificate verification failed: issuer is not trusted (https://ServerAdd) . Process command: E:\(svn.exe Path) log https://TrunkURL -r "{2010-11-08T02:12:20Z}:{2010-11-08T02:13:21Z}" --verbose --xml --no-auth-cache --non-interactive at ThoughtWorks.CruiseControl.Core.Sourcecontrol.ProcessSourceControl.Execute(ProcessInfo processInfo) at ThoughtWorks.CruiseControl.Core.Sourcecontrol.Svn.GetModifications(IIntegrationResult from, IIntegrationResult to) at ThoughtWorks.CruiseControl.Core.Sourcecontrol.QuietPeriod.GetModificationsWithLogging(ISourceControl sc, IIntegrationResult from, IIntegrationResult to) at ThoughtWorks.CruiseControl.Core.Sourcecontrol.QuietPeriod.GetModifications(ISourceControl sourceControl, IIntegrationResult lastBuild, IIntegrationResult thisBuild) at ThoughtWorks.CruiseControl.Core.IntegrationRunner.GetModifications(IIntegrationResult from, IIntegrationResult to) at ThoughtWorks.CruiseControl.Core.IntegrationRunner.Integrate(IntegrationRequest request) We are using VisualSVN Server and CC.NET for this adventure. Tips, suggestions will be highly appreciated. Thanks

  Read the article

• Practical tips when transitioning to xmonad?

  - by meder

  I like the idea and concept of xmonad, however I still keep going back to gnome after an hour or so. This feels like when I first tried to learn vim, but I've gotten past the learning curve point and can't live without vim nowadays. I'm sure the time will come for xmonad too, but I was wondering if current xmonad users can provide transitional tips? FYI, I'm on dual monitors ( 19 inch and 17 inch ). Example of an issue I'm having while in this "transitional" stage: How do you manage keeping the browser and other programs that are most commonly used in full screen mode, since by default I think it opens up in a small tile that takes up a portion of the screen? Do you just shortcut it to make it open full screen, or do you actually not maximize it? Or are there advanced methods through preferences in the conf file, making certain programs take up X space?

  Read the article

• Small business VPN solution

  - by Crash893

  I've been looking for a while but I'd like to to implement a vpn solution for anywhere from 1-5 employees at a time (possibly 10 in a year or so) edit: Basically I would like outside users to fire up a client or open a web page and be able to access things inside the company network (share drives / printers/ webapps /etc) I've looked at Astaro Gateway but im not sure if that's the right tool for the job. I know "best" is a subjective term so i would like to break it into to different suggestions 1) what is the cheapest solution given the criteria above 2) what solution will result in the least amount of headaches from the point of view of maintenance and learning curve.

  Read the article

• Set up a root server using Ubuntu and Virtualization

  - by Daniel Völkerts

  Hello, I'd like to setup a fresh root server and install a linux based virtualization on it. My thoughts are on: Intel VTs Hardware Ubuntu 9.10 KVM based virt. The access to the root server will only be SSH for Administration. Has anybody done this before, what was your glues discovered in the daily use? My requirements are: very secure, so the root server only has ssh to the dom-0 and minimalistic ports for the guest (e.g. http/s). good monitoring of host/guest (my idea is to using zabbix for it) easy and fast administration (how are the command line tools working for you? cryptiv? high learning curve?) I'm pleased to learn from your suggestions. Regards, Daniel Völkerts

  Read the article

• Converge Voice and Data networks using Sonicwall

  - by skinneejoe

  We are looking to converge VOIP and Data traffic onto a single wire so that our client's VOIP phones pass data through to the users computer. We are specing out a new Sonicwall NSA appliance to handle routing functions and layer 2 switches to manage VLANS. Not a huge network, medium sized. What should I know about converging the networks onto a single wire? Obviously I'll want to prioritize voice traffic, is this handled solely in the Sonicwall with QoS configurations or do the layer 2 switches need to be configured differently? Any other pitfalls I should be aware of, or any good resources for learning more?

  Read the article

• Should I keep my ex-employer's data?

  - by Jurily

  Following my brief reign as System Monkey, I am now faced with a dilemma: I did successfully create a backup and a test VM, both on my laptop, as no computer at work had enough free disk space. I didn't delete the backup yet, as it's still the only one of its kind in the company's history. The original is running on a hard drive in continuous use since 2006. There is now only one person left at the company, who knows what a backup is, and they're unlikely to hire someone else, for reasons very closely related to my departure. Last time I tried to talk to them about the importance of backups, they thought I was threatening them. Should I keep it? Pros: I get to save people from their own stupidity (the unofficial sysadmin motto, as far as I know) I get to say "I told you so" when they come begging for help, and feel good about it I get to say nice things about myself on my next job interview Nice clean conscience Bonus rep with the appropriate deities Cons: Legal problems: even if I do help them out with it, they might just sue me for keeping it anyway, although given the circumstances I think I have a good case Legal problems: given the nature of the job and their security, if something leaks, I'm a likely target for retaliation Legal problems: whatever else I didn't think about I need more space for porn. Legal problems. What would you do?

  Read the article

• Web application design with distributed servers

  - by Bonn

  I want to build a web application/server with this structure: main-server sub-server transaction-server (create, update, delete) view-server (view, search) authentication-server documents-server reporting-server library-server e-learning-server The main-server acts as host server for sub-server. I can add many sub-servers and connect it to main-server (via plug-play interface maybe), then it can begin querying data from another sub-servers (which has been connected to the main-server). The sub-servers can be anywhere as long as connected to internet. The main-server can manage all sub-servers which are connected to it (query data, setting permission between sub-servers, etc). The purpose is simple, the web application will be huge as the company grows, so I want to distribute it into small connected plug-able servers. My question is, does the structure above already have a standardized method? or are there any different views? what are the technologies needed? I need a lot of researches before the execution plan begin. thanks a lot.

  Read the article

• how to diagnose a hard system seizure? Dell+Ubuntu

  - by rob

  I've got Ubuntu 9.10 on a Dell Vostro 420 desktop, a little over a year old, which I use for plain vanilla work stuff (email, web, terminal, text editor). Every now and then, at totally random times, it completely freezes on me. Hard. Mouse and keyboard stop working, cursor stops blinking, clock stops moving. All I can do is hold down the power button on the front of the box to shut it off. Sometimes it happens after several months of continuous uptime; sometimes it happens a few minutes after a reboot, while all I've done is open a terminal to look at log files, or maybe firefox to do a google search. Each time, there is nothing at all in /var/log/messages at the time of the crash. This makes it seem like a hardware problem, and indeed a few months ago I opened the box and wiggled everything and the problem went away for a while. But now it's back. I went in and checked everything, took out each RAM card and reseated. No luck. I ran all the system diagnostics (the long version) and everything passed with flying colors. Something is messed up in this box, but without any useful logs or failed tests, how in the world am I going to find it? And of course, Dell's not gonna help me cause I went and replaced Windows with Ubuntu. What steps would you take next to track down this problem?

  Read the article

• GUI frontend for octave on Linux

  - by Homunculus Reticulli

  I recently installed Octave on my Ubuntu 10.0.4 LTS box. Out of the box, this is a console only app. This makes the learning curve a bit steeper than what I would like it to be, and I am looking for a GUI frontend that looks more like Matlab. I have seen a few project (QtOctave etc), but most of them seem either discontinued, no longer under active development, or are no longer free. Can anyone recommend a good open source/free GUI for Octave on Linux? Preferably, one that is as close as possible to Matlab's GUI.

  Read the article

• Minimum Requirements for (open) Solaris?

  - by Electrons_Ahoy

  I'm thinking about knocking together a Solaris box at home to act as a combination server and learning exercise. What are the minimum hardware specs I can throw at it such that it'll be actually usable? I'd be cobbling the machine together from a stack of various x86 PC spares/leftovers. Does anyone have experience with Solaris at the lower end of the spectrum? The Sun site, for example, claims it'll run with as little as 255 megs of ram, but is it worth the exercise with less than a gig? Will my old Pentium II 450 cut the mustard? (I'm willing to throw a couple of bucks at pricewatch/mwave/newegg on this, but if I need to build a better rig than my main PC, I may not bother.)

  Read the article

• Looking at desktop virtualization, but some users need 3D support. Is HP Remote Graphics a viable solution?

  - by Ryan Thompson

  My company is looking at desktop virtualization, and are planning to move all of the desktop compute resources into the server room or data center, and provide users with thin clients for access. In most cases, a simple VNC or Remote Desktop solution is adequate, but some users are running visualizations that require 3D capability--something that VNC and Remote Desktop cannot support. Rather than making an exception and providing desktop machines for these users, complicating out rollout and future operations, we are considering adding servers with GPUs, and using HP's Remote Graphics to provide access from the thin client. The demo version appears to work acceptably, but there is a bit of a learning curve, it's not clear how well it would work for multiple simultaneous sessions, and it's not clear if it would be a good solution to apply to non-3D sessions. If possible, as with the hardware, we want to deploy a single software solution instead of a mishmash. If anyone has had experience managing a large installation of HP Remote Graphics, I would appreciate any feedback you can provide.

  Read the article

• What is the correct root file to import to aptana from an xampp folder/existing web app or git repository?

  - by gaff

  Very noob question - all of this is new to me - not really sure how to get started. Overview: I'm taking over an existing wep project that has been developed in aptana and deployed in xampp setup - I also have access to Git repository on local directory. I want to import the web application into aptana, run it and begin updating/editing - bit of steep learning curve for me What is the best way to import? And what should I import? What should it look like in aptanan? I tried importing what I think is the root file from the git folder ("existing folder as new project")- it contains things like css, doc, img and js. This looks right to me - but might not be. Thanks, Gaff

  Read the article

• Sharepoint Central Administration stuck / high CPU usage

  - by johnnyb10

  I'm using WSS 3 and I recently added a new web application to my SharePoint Server. After adding it, I wasn't able to open the Central Administration site. I also noticed that there was a w3wp.exe error (Event ID 1000) in the Event Viewer. The situation now is that the w3wp.exe process is hovering around 50% CPU usage continuously. I installed a program called IIS Peek, and it shows continuous GET requests on the Central Administration site; this happens even if I stop the Central Administration site in IIS. The IP addresses identified in the GET request is my workstation, which is what I used to attempt to access Central Administration after I created the new web application. Can someone explain what's going on and how I might fix it? It seems as if my computer tried to access Central Administration and then it hung, but the page requests that were happening at the time are somehow continuing over and over again. So my two problems are the inability to access Central Administration, and the CPU Usage of w3wp.exe, which I'm assuming are two symptoms of the same problem. I'd like to know if there's anything I can do besides restarting IIS, because we have clients accessing other sites on this server. Thanks.

  Read the article

• Resolving host names to their domain name in an internal BIND domain

  - by Adam Plumb

  I'm setting up a domain on my home network for learning purposes, using BIND on CentOS to act as the name server. I've got the name server up and running as type master for my internal domain (plumbnicoll.family), and can do forward and reverse lookups from other computers in my LAN. For example, host office2.plumbnicoll.family correctly returns office2.plumbnicoll.family has address 192.168.1.3. What I'd like is to be able to resolve just office2 to its address, without needing to put .plumbnicoll.family at the end. Is this possible, or even desirable to do? I'm running a mixed environment at home with both Linux and Windows computers.

  Read the article

• Media Center is sending duplicate #'s when changing channels

  - by Robert

  I recently switched from cable to DirecTV (satellite). I went through the "Set up TV signal" in Media Center, and I went through the manual setup of the remote as it didn't recognize the DirecTV remote. All seemed okay, except sometimes (often - about 1/2 the time) when I select a channel in Media Center's guide it sends 5527 instead of 527 or 5446 instead of 546 - so it doesn't change the channel correctly. (I see the numbers show up on the TV screen before the channel changes.) I tried re-learning the remote, but the problem is still there. (Media Center is changing channels through the IR Blaster attached to the front of the DirecTV box.)

  Read the article

• how to start with unmanaged vps?

  - by GaVrA

  Hello! I have a managed VPS, so whatever i need i can just ask my support, and they will do it for me. Now i plan to migrate to unmanaged VPS, so i need some guides, tips on how and where to start learning. I will have more specific questions once i start using it, but now i just need some general answers about this topic. Thanks. Update: Ok, i have decided to go for unmanaged VPS with cPanel. OS is CentOS-5. I contacted support only for some small(i think) things like creating new account in whm, some database importing, installing new software(rare)... What i will be using is apache, php, mysql. I think i will be able to cope with upgrading to new versions, so the thing that interests me the most is security i guess.

  Read the article

• How to allow an internal server accept remote connections not through RD Gateway

  - by Matt Ahrens

  So, I help administrate a collection of servers running various windows server environments. We have a RD Gateway server, properly configured, to gatekeep for us. It does not have the other servers listed in it's server farm category, though. I just added a refurbished server for a non-profit development environment that is sharing the rack space and port. I would like this server to be accessible via remote connection, but not require RD gateway certification (I cannot add the users for this development server to our gateway since they do not work for the organization hosting the rack.) Is there any way for me to add this dev. server as an exception to which servers should require RD Gateway clearance, or otherwise let users bypass RD gateway credentials for this one machine? Thanks, and let me know if I am misinformed on how RD gateway works or anything. I am still learning.

  Read the article

• Windows VPN always disconnects after < 3 minutes, only from my network

  - by hemp

  First, this problem has existed for almost two years. Until serverfault was born, I pretty much gave up on solving it - but now, hope is reborn! I've set up a Windows 2003 server as a domain controller and VPN server at a remote office. I am able to connect to and work over the VPN from every windows client I've tried, including XP, Vista, and Windows 7 without issue, from at least five different networks (corporate and home, domain and non.) It works fine from all of them. However, whenever I connect from clients on my home network, the connection drops (silently) after 3 minutes or less. After a short while, it will eventually tell me the connection has dropped and attempt to redial/reconnect (if I've configured the client that way.) If I reconnect, the connection will re-establish and appear to work correctly, but again will silently drop, this time after a seemingly shorter time period. These are not intermittent drops. It happens every single time, in exactly the same way. The only variable is how long the connection survives. It doesn't matter what type of traffic I send. I can sit idle, send continuous pings, RDP, transfer files, all of that at once - it makes no difference. The result is always the same. Connected for a few minutes, then silent death. Since I doubt anyone has experienced this exact situation, what steps can I take to troubleshoot my evanescing VPN?

  Read the article

• Is it possible to have zsh+keychain+tmux not ask for keys?

  - by Wayne Werner

  I'm using tmux and zsh, and I've recently been learning about ssh-agent and keychain. From the manpage for zsh, it says that it will source .zlogin only if the shell is, well, a login shell. Following advice I read, I stuck keychain --clear in my .zlogin, which worked perfectly. When I logged into the box I had to unlock my key. However, each time I create a new window in tmux, it clears/makes me re-add my key. This is a little annoying... but I can understand it if, in fact, each new tmux window is a login window. I haven't been able to find much help outside of the manpages on this topic. So is each new tmux window a login shell, or is there any way that I can make it not clear my keys only when I create a tmux window?

  Read the article

• Which CMS for a mobile app? No HTML, just XML or JSON

  - by Sascha

  I am a newbie in content management systems. I would need a CMS that can transfer content by XML or JSON to a client. It is ok if the CMS can also manage HTML websites, but the priority is on the data transfer over a web service. Which is the best CMS to use here? I want to avoid spending endless hours learning all the big CMS systems just to find out that they don't support this feature or that it's badly integrated. Thanks.

  Read the article

• php programming

  - by HARSHA

  Hi, i am learning php,i downloded the xampp.and Apache server,Mysql are running properly in Xampp Control panel. I tried with a simple program that is hello world,i created a new folder in htdocs, and i saved my program in that new folder with .php extention. But when i run the program then is showing a error as follows ------ Object not found! The requested URL was not found on this server. If you entered the URL manually please check your spelling and try again. If you think this is a server error, please contact the webmaster. Error 404 localhost 18-5-2010 11:51:44 Apache/2.2.14 (Win32) DAV/2 mod_ssl/2.2.14 OpenSSL/0.9.8l mod_autoindex_color PHP/5.3.1 mod_apreq2-20090110/2.7.1 mod_perl/2.0.4 Perl/v5.10.1

  Read the article

• Can't find a wireless access point's IP address after changing router IP/LAN settings

  - by flagg19

  I have a modem/router, Netgear DG834, and a wireless access point (AP), Netgear WG602. The AP is directly connected to the router. My old working configuration was: Router IP address : 192.168.0.1 Access point IP address: 192.168.0.10 My new configuration is: Router IP address : 192.168.1.1 Access point IP address: ???.???.???.??? I changed my router's IP address/LAN settings to set up a VPN with another Netgear router that had the same LAN configuration. The wireless network is still up and perfectly working, but I can't find the AP's IP address. I've tried broadcast ping but the AP won't respond. I looked at the router "attached devices", but it's not there. I've played around with Nmap and arp request but the AP is totally invisible. I can fix it by resetting it to factory settings, but I'm very interested in learning more about this problem. I'm also interested in network security and this fact of having an invisible AP well, it's something I'd like to understand.

  Read the article

• What are the minimum required modules to run WordPress

  - by Mister IT Guru

  Recently a 'consultant' came in to talk to bean counters at my place of employment, with regards to being more efficient with our IT infrastructure. They suggested to be more efficient we should only load the Apache modules that are required on our web servers. (This is just 1 of 1Ks of suggestions). The Bean Counters are very excited, and prepared for me to spend the time to investigate this avenue of cost cutting. I don't mind this mundane exercise, I see it as a learning experience! I guess this leads me to the actual question: How can I determine the minimum required apache modules for a PHP based application without actually going through the code, or plain old trial and error?

  Read the article

< Previous Page | 178 179 180 181 182 183 184 185 186 187 188 189  | Next Page >