Search Results

Search found 10789 results on 432 pages for 'cpu upgrade'.

Page 182/432 | < Previous Page | 178 179 180 181 182 183 184 185 186 187 188 189  | Next Page >

  • What could cause a huge packet loss in Ubuntu 9.10, for both wired and wireless?

    - by xzenox
    I was previously using 9.04 fine (and in fact, I am posting this from my old 9.04 live cd). I tested the following install steps in a virtualbox vm prior to following the sames ones to upgrade my laptop: Download/burn ubuntu minimal cd (12mb one) Install ubuntu minimal sudo apt-get update sudo apt-get upgrade sudo apt-get ubuntu-desktop ubuntu-standard In the VM worked fine and I found myself with a working 9.10 ubuntu, network worked fine and I was able to test my backups and DropBox without a hitch (host was 9.04). When I followed the same steps on my laptop, everything worked up to after 9.10 being installed and working. As far as I can tell, everything besides eth0/wireless works. For some reason, I am unable to access the internet. Ping reports that over 99% of packets get lost (over an hour or so of pinging). This means for example that if I try hard enough, I can load a webpage but only at the cost of much patience... This happens both for a wired and wireless connection to my wrt310n (updated with latest firmware). At first I thought that it could be related to the ipv6 issues ppl have been experiencing however even after disabling ipv6 at the kernel level (through grub), I still get the issue. I do not think this is related to DNS issues or the likes since even when I ping my ISP's gateway IP, I have the same amount of packet loss. No DNS resolving should be required there. Access to my router works peachy with no packet loss there. I've tried different MTU values but to no avail. Note that this issue affects every web-enabled application: firefox, ping, synaptic, etc. The same hardware/router combo works with 9.04 but not with 9.10. In fact, when I did: sudo apt-get ubuntu-desktop ubuntu-standard after 9.10 minimal was installed, it downloaded over 400mb of packages without a hitch so my guess is that one of those packages either in ubuntu-desktop or ubuntu-standard is causing havok. Thoughts?

    Read the article

  • cPanel web servers mounting home partition to a NAS or SAN

    - by Scott
    I currently have 2 cPanel web servers that are little 1RU dual cpu quad core xeons. They have a lot of resources for processing and handling web requests, and never exceed more than 10% cpu usage. They also have plenty of RAM. The problem is though that they both have RAID 1 160Gb SAS hard disk drives in them that are 75% full, and growing by the day. I didnt think that the amount of disk usage would be so high, but due to the nature of the sites hosted, this has become an issue. The easy fix would be just to upgrade the hard drives to something bigger (probably not of the SAS variety), but I am thinking of keeping the current machines as "processing servers" and buying a central "storage server" with about 12TB of storage. The /home/ partition on each of the 1RU servers would be mounted to a NAS or SAN point on this central storage server. My questions are: - Has anyone got a cPanel setup where they mount /home/ to a NAS or SAN elsewhere? If so, can you provide details as to what you did and how it went :) - Any recommendations on networking? Is gigabit ethernet enough? Is TCP/IP going to be a noticable performance problem? Anyone used a TOE key? - Anyone benchmarked or had any performance issues with SAN over NAS? Any help greatly appreciated. Scott

    Read the article

  • Running Windows Update inside Windowx XP Mode

    - by Noam Gal
    I am working on a Win 7 Ultimate machine, and was using XP for some development tasks (for compatibility checks). Everything worked like a charm on the XP, including updates. Two days ago I had to switch computer (mainly a new motherboard/cpu), and I had just stuck my old HD inside the newer case. Win 7 worked like a charm - installed all the new drivers, identified everything automatically, no sweat. The trouble started when I tried running my old XP mode - it won't launch, complaining about the cpu change. I figured it's not a big deal, and I deleted the VM, and re-ran XP mode. It told me it can't find it, and offered to create a new one, just what I wanted. I had finished setting up the new XP mode VM, and it seems to work just fine. Got it to use the host network adapter, so I can surf from "inside". But I can't get Windows Update to run. Whenever I click on the "Custom" button on the WU site, after a short while, I get the [Error number: 0x80072EFD] page. I tried several solution from around the web for it (clearing some cache and restarting the wuauserv, even a microsoft fix-it run), but still nothing seems to work. Anyone here has any new tip for me? Thanks.

    Read the article

  • IPMI sdr entity 8 (memory module) only showing 3 records?

    - by thinice
    I've got two Dell PE R710's - A has a single socket and 3 DIMMs in one bank B has both sockets and 6 (2 banks @ 3 DIMMs) filled The output from "ipmitool sdr entity 8" confuses me - according to the OpenIPMI documentation these are supposed to represent DIMM slots. Output from A (1 CPU, 3 DIMMS, 1 bank.): ~#: ipmitool sdr entity 8 Temp | 0Ah | ok | 8.1 | 27 degrees C Temp | 0Bh | ns | 8.1 | Disabled Temp | 0Ch | ucr | 8.1 | 52 degrees C Output from B (2 CPUs, 3 DIMMS in both banks, 6 total): ~#: ipmitool sdr entity 8 Temp | 0Ah | ok | 8.1 | 26 degrees C Temp | 0Bh | ok | 8.1 | 25 degrees C Temp | 0Ch | ucr | 8.1 | 51 degrees C Now, I'm starting to think this output isn't DIMMS themselves, but maybe a sensor for each bank and something else? (Otherwise, shouldn't I see 6 readings for the one with both banks active?) The CPU's aren't near 50 deg C, so I doubt the significantly higher reading is due to proximity - Is anyone able to explain what I'm seeing? Does the output from my ipmitool sdr entity 8 -v here on pastebin seem to hint at different sensors? The sensor naming conventions are poor - seems like a dell thing. Here is output from racadm racdump

    Read the article

  • java.lang.OutOfMemoryError: unable to create new native thread

    - by Brad
    I consistently get this exception when trying to run my Junit tests on my mac: java.lang.OutOfMemoryError: unable to create new native thread at java.lang.Thread.start0(Native Method) at java.lang.Thread.start(Thread.java:658) at java.util.concurrent.ThreadPoolExecutor.addIfUnderMaximumPoolSize(ThreadPoolExecutor.java:727) at java.util.concurrent.ThreadPoolExecutor.execute(ThreadPoolExecutor.java:657) at java.util.concurrent.AbstractExecutorService.submit(AbstractExecutorService.java:92) at com.google.appengine.tools.development.ApiProxyLocalImpl$PrivilegedApiAction.run(ApiProxyLocalImpl.java:197) at com.google.appengine.tools.development.ApiProxyLocalImpl$PrivilegedApiAction.run(ApiProxyLocalImpl.java:184) at java.security.AccessController.doPrivileged(Native Method) at com.google.appengine.tools.development.ApiProxyLocalImpl.doAsyncCall(ApiProxyLocalImpl.java:172) at com.google.appengine.tools.development.ApiProxyLocalImpl.makeAsyncCall(ApiProxyLocalImpl.java:138) The same set of unit tests pass perfectly fine on ubuntu and windows. Some information about my system resources on the mac: $ ulimit -a core file size (blocks, -c) 0 data seg size (kbytes, -d) unlimited file size (blocks, -f) unlimited max locked memory (kbytes, -l) unlimited max memory size (kbytes, -m) unlimited open files (-n) 1024 pipe size (512 bytes, -p) 1 stack size (kbytes, -s) 8192 cpu time (seconds, -t) unlimited max user processes (-u) 266 virtual memory (kbytes, -v) unlimited $ java -version java version "1.6.0_24" Java(TM) SE Runtime Environment (build 1.6.0_24-b07-334-10M3326) Java HotSpot(TM) 64-Bit Server VM (build 19.1-b02-334, mixed mode) The reason I dont think this is an application issue is because the same tests pass in different environments. I have tried setting heap to 1024m, 512m and setting the stack to 64k and 128k (and each of these combinations) with no luck. My open files was originally 256 and I have bumped this to 1024. I have been googling around for a bit and all posts say to decrease heap size and increase stack size but that doesnt seem to help. Anyone have anymore ideas? EDIT: Here are is some environment information on my ubuntu box: $ ulimit -a core file size (blocks, -c) 0 data seg size (kbytes, -d) unlimited scheduling priority (-e) 20 file size (blocks, -f) unlimited pending signals (-i) 16382 max locked memory (kbytes, -l) 64 max memory size (kbytes, -m) unlimited open files (-n) 1024 pipe size (512 bytes, -p) 8 POSIX message queues (bytes, -q) 819200 real-time priority (-r) 0 stack size (kbytes, -s) 8192 cpu time (seconds, -t) unlimited max user processes (-u) unlimited virtual memory (kbytes, -v) unlimited file locks (-x) unlimited $ java -version java version "1.6.0_24" Java(TM) SE Runtime Environment (build 1.6.0_24-b07) Java HotSpot(TM) 64-Bit Server VM (build 19.1-b02, mixed mode)

    Read the article

  • Squid proxy in cent os often disconnected with error : tunnelConnectTimeout(): tunnelState->servers is NULL

    - by Ela
    I am having very often internet disconnection problem with Squid proxy service. My server config; OS: CentOS release 6.3 (Final) model name : Intel(R) Core(TM) i7-2600 CPU @ 3.40GHz cpu MHz : 1600.000 My Local systems IP range:192.168.2.x Server IP: 192.168.2.11 Also this server is configured with lamp for development,Samba SMB file service manager and No svn currently. So i see maximum possibility is this squid proxy since this is where it stops to connect and am sure when i restart the server net started working so something wrong with this squid service only. And this server is connected with local 14 other windows machines and basically serves as a central development node. I am able to resolve it by restarting the server fully some time or sometimes by restarting the squid proxy which is totally killing our development. I have attached my cache log file here for the error info. Cache log file Sample error log: 2013/07/01 13:25:38| tunnelConnectTimeout(): tunnelState->servers is NULL 2013/07/01 13:25:41| tunnelConnectTimeout(): tunnelState->servers is NULL 2013/07/01 13:25:41| tunnelConnectTimeout(): tunnelState->servers is NULL 2013/07/01 13:25:50| clientProcessRequest: Invalid Request 2013/07/01 13:26:05| tunnelConnectTimeout(): tunnelState->servers is NULL Some help can make our lives easier, Thanks in advance.

    Read the article

  • Setup for a live (low-latency) audio video broadcast over Wi-Fi?

    - by Majal Mirasol
    The Upgrade We are capturing audio (from mixer) and video (from a camera) from a main auditorium and passing it to separate rooms within the building. We used to have done this via manual audio/video cables and wires. We wanted to "upgrade" the system and wirelessly broadcast the stream via Wi-Fi. The Problem In our current setup (Wirecast running on A10 on a Wireless-N network), we have the problem of delay. Our streams are delayed from a minute up to five minutes on the clients (laptop/iPad/Android). This had not been a problem from the previous wired connections. Since the wireless network is local, we thought that a delay of less than a second should be achievable. Our Question And so it goes. Anybody there who has any experience for a setup that has both low latency and at the same time user-friendly to clients streaming in the program? Any recommendations would be highly appreciated. (Our current setup in on Windows 7, but setup on a dedicated Linux box is preferred, if achievable.)

    Read the article

  • Explorer.exe not starting after login on Windows Server 2003 (Terminal Services and console)

    - by Pepperoni Icecream
    When users login to a Windows Server 2003 R2 running Terminal Services they have a blank desktop. Upon inspection, explorer.exe is not running. When I login as administrator, using either RDP or to the console, I am having the same issue. I can pull up the taskman and start explorer.exe manually. I have another Terminal Server setup exactly the same way (same apps, settings, GPO, etc . . .) the only difference is we deployed Symantec Endpoint Client 11.0.5 on Friday. For some reason the working Terminal Server is still on 11.0.4, but the suspect server received the 11.0.5 client upgrade. I checked the eventviewer for any relevant explorer.exe entries to no avail. It seems that if SEP is preventing explorer.exe from starting at login it would do the same for the domain admin starting explorer.exe from the taskman. I disabled the SEP client and services on the server and issued smc -stop and tried logging in again. Still no explorer.exe. So I'm not sure if the client upgrade is relevant but it is worth mentioning since that was the last system change. The 2 servers are members of a NLB group. I took the bad terminal server out of the group until the issue is resolved. Actually stopped the host using NLB manager Any help is appreciated.

    Read the article

  • IIS 6 + ASP.NET web service - DW20 and stackoverflow exception

    - by pcampbell
    Consider an ASP.NET SOAP web service that starts up fine, but craters hard when receiving its first hit. Please note that this is deployment works in the Test environment, but not in the PreProd environment. Both are Windows 2003 SP3 + IIS 6 + ASP.NET 3.5. All up-to-date. The behaviour that we're seeing is: restart the site & app pool the app pool is configured to run under Network Service. browsing to the .asmx and .wsdl responds normally, as expected. send a normal well-formed SOAP request / normal payload to the web service 100% CPU usage after 5 seconds, the page request / site returns "Service Unavailable" no entry is created in the IIS log file (i.e. c:\windows\system32\logfiles\W3C-foo) the app pool ends up being stopped The processes that hit the CPU hard are dw20.exe. I am unsure why Dr Watson is involved here. Event Log shows an ASP.NET Runtime error: Task Manager: Event log text: EventType clr20r3, P1 w3wp.exe, P2 6.0.3790.3959, P3 45d6968e, P4 errormanagement, P5 1.0.0.0, P6 4b86a13f, P7 24, P8 0, P9 system.stackoverflowexception, P10 NIL. Questions Any thoughts on what this system.stackoverflow exception might be? Given that the code is the same between environments, might it be a payload problem? Could it be a configuration issue? You can see the name of my .NET assembly there in the exception message: "ErrorManagement"

    Read the article

  • lm-sensors - always returns 32 degrees (celsius) for temperature

    - by mopoke
    On my VIA EPIA motherboard (using VIA VT8231 ISA bridge), I get strange output for the lm-sensors temperature reading. It always returns 32 degrees (celsius). I have previously had correct output for temperature (my munin graphs show temperatures typically in the range of 50 to 60 degrees. I've tried uninstalling (and purging) the lm-sensors package, have re-run sensors-detect a number of times and rebooted but nothing seems to change the output. I am running Ubuntu Karmic Koala (9.10). Anyone got any bright ideas on what I might have missed? uname -a: Linux george 2.6.31-16-386 #53-Ubuntu SMP Tue Dec 8 06:39:34 UTC 2009 i686 GNU/Linux cpuinfo: processor : 0 vendor_id : CentaurHauls cpu family : 6 model : 7 model name : VIA Samuel 2 stepping : 3 cpu MHz : 399.000 cache size : 64 KB fdiv_bug : no hlt_bug : no f00f_bug : no coma_bug : no fpu : yes fpu_exception : yes cpuid level : 1 wp : yes flags : fpu de tsc msr cx8 mtrr pge mmx 3dnow up bogomips : 800.04 clflush size : 32 power management: lspci: 00:00.0 Host bridge: VIA Technologies, Inc. VT8601 [Apollo ProMedia] (rev 05) 00:01.0 PCI bridge: VIA Technologies, Inc. VT8601 [Apollo ProMedia AGP] 00:11.0 ISA bridge: VIA Technologies, Inc. VT8231 [PCI-to-ISA Bridge] (rev 10) 00:11.1 IDE interface: VIA Technologies, Inc. VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE (rev 06) 00:11.2 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 1e) 00:11.3 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 1e) 00:11.4 Bridge: VIA Technologies, Inc. VT8235 ACPI (rev 10) 00:11.5 Multimedia audio controller: VIA Technologies, Inc. VT82C686 AC97 Audio Controller (rev 40) 00:12.0 Ethernet controller: VIA Technologies, Inc. VT6102 [Rhine-II] (rev 51) 01:00.0 VGA compatible controller: Trident Microsystems CyberBlade/i1 (rev 6a) sensors: acpitz-virtual-0 Adapter: Virtual device temp1: +32.0°C (crit = +60.0°C)

    Read the article

  • No OS will boot, all freeze

    - by Gyan
    This is for a computer with the following configuration: Asus P5KPL-AM/PS motherboard Pentium D 820 (dual core 2.8 GHz) 1 x 2 GB DDR2-800 Transcend RAM 1 SATA2 Samsung 160 GB HDD 1 PATA LG CD/DVD Writer PS/2 generic Keyboard USB Razer mouse The computer was working fine till a month ago with a Hitachi HDD in place of the Samsung. But that drive died and I sent it in for warranty replacement. Since then and till last week, the computer had not been turned on. I then got hold of a spare but XPSP2-loaded Samsung drive from another computer and decided to get this computer temporarily running. However, when I tried to boot into XP, it didn't load. It got stuck at the first graphical screen. When trying Safe Mode, the file list would be updated up to diskio.sys and then freeze. If I tried to boot Kubuntu off a CD, I would get past the first menu, but then get stuck at the subsequent graphical interface in the loading process. A similar thing happend with a friend's Windows XP-on-a-pen-drive. I switched the RAM into the other slot, but no luck. Then I booted the Ultimate Boot CD and ran Memtest86+ and a couple of the bundled CPU stress tests but these detected no errors. Some searching on the Internet brought up the notion of the CPU failing to switch from "real" to "protected mode". I'm hoping to get a fix on what the problem is and what I can do about it. Edit: I've flashed to the latest BIOS, but that doesn't help. Also, Knoppix LiveCD also freezes. I notice that the LED in my mouse goes off at the time of freeze, but trying to boot without the mouse connected produces the same result.

    Read the article

  • JVM system time runs faster than HP UNIX OS system time

    - by winston
    Hello I have the following output from a simple debug jsp: Weblogic Startup Since: Friday, October 19, 2012, 08:36:12 AM Database Current Time: Wednesday, December 12, 2012, 11:43:44 AM Weblogic JVM Current Time: Wednesday, December 12, 2012, 11:45:38 AM Line 1 was a recorded variable during WebLogic webapp startup. Line 2 was output from database query select sysdate from dual; Line 3 was output from java code new Date() I have checked from shell date command that line 2 output conforms with OS time. The output of line 3 was mysterious. I don't know how it comes from Java VM. On another machine with same setting, the same jsp output like this: Weblogic Startup Since: Tuesday, December 11, 2012, 02:29:06 PM Database Current Time: Wednesday, December 12, 2012, 11:51:48 AM Weblogic JVM Current Time: Wednesday, December 12, 2012, 11:51:50 AM Another machine: Weblogic Startup Since: Monday, December 10, 2012, 05:00:34 PM Database Current Time: Wednesday, December 12, 2012, 11:52:03 AM Weblogic JVM Current Time: Wednesday, December 12, 2012, 11:52:07 AM Findings: the pattern shows that the longer Weblogic startup, the larger the discrepancy of OS time with JVM time. Anybody could help on HP JVM? On HP UNIX, NTP was done daily. Anyway here comes the server versions: HP-UX machinex B.11.31 U ia64 2426956366 unlimited-user license java version "1.6.0.04" Java(TM) SE Runtime Environment (build 1.6.0.04-jinteg_28_apr_2009_04_46-b00) Java HotSpot(TM) Server VM (build 11.3-b02-jre1.6.0.04-rc2, mixed mode) WebLogic Server Version: 10.3.2.0 Java properties java.runtime.name=Java(TM) SE Runtime Environment java.runtime.version=1.6.0.04-jinteg_28_apr_2009_04_46-b00 java.vendor=Hewlett-Packard Co. java.vendor.url=http\://www.hp.com/go/Java java.version=1.6.0.04 java.vm.name=Java HotSpot(TM) 64-Bit Server VM java.vm.info=mixed mode java.vm.specification.vendor=Sun Microsystems Inc. java.vm.vendor="Hewlett-Packard Company" sun.arch.data.model=64 sun.cpu.endian=big sun.cpu.isalist=ia64r0 sun.io.unicode.encoding=UnicodeBig sun.java.launcher=SUN_STANDARD sun.jnu.encoding=8859_1 sun.management.compiler=HotSpot 64-Bit Server Compiler sun.os.patch.level=unknown os.name=HP-UX os.version=B.11.31

    Read the article

  • X11 performance problem after upgrading from Centos3 to Centos5 with an ATI Rage XL

    - by Marcelo Santos
    After upgrading a computer from Centos3 to Centos5 an application that does a lot of scrolling took a very high performance hit. top tells me that X is using a lot of CPU and that was not happening before. The machine has an ATI Rage XL with 8MB and X is using the ati driver as there is no proprietary ATI driver for this board on linux. The xorg.conf: Section "Device" Identifier "Videocard0" Driver "ati" EndSection Section "Screen" Identifier "Screen0" Device "Videocard0" DefaultDepth 24 SubSection "Display" Viewport 0 0 Depth 24 Modes "1024x768" "800x600" "640x480" EndSubSection EndSection Section "DRI" Group 0 Mode 0666 EndSection A similar machine that still has Centos3 installed is able to start DRI on the X server while this one is not, this is the Xorg.0.log for the Centos5 machine: drmOpenDevice: node name is /dev/dri/card0 drmOpenDevice: open result is -1, (No such device or address) drmOpenDevice: open result is -1, (No such device or address) drmOpenDevice: Open failed drmOpenDevice: node name is /dev/dri/card0 drmOpenDevice: open result is -1, (No such device or address) drmOpenDevice: open result is -1, (No such device or address) drmOpenDevice: Open failed [drm] failed to load kernel module "mach64" (II) ATI(0): [drm] drmOpen failed (EE) ATI(0): [dri] DRIScreenInit Failed (II) ATI(0): Largest offscreen areas (with overlaps): (II) ATI(0): 1024 x 1279 rectangle at 0,768 (II) ATI(0): 768 x 1280 rectangle at 0,768 (II) ATI(0): Using XFree86 Acceleration Architecture (XAA) Screen to screen bit blits Solid filled rectangles 8x8 mono pattern filled rectangles Indirect CPU to Screen color expansion Solid Lines Offscreen Pixmaps Setting up tile and stipple cache: 32 128x128 slots 10 256x256 slots (==) ATI(0): Backing store disabled (==) ATI(0): Silken mouse enabled (II) ATI(0): Direct rendering disabled (==) RandR enabled I also tried using EXA instead of XAA and setting: Option "AccelMethod" "XAA" Option "XAANoOffscreenPixmaps" "true" uname -a Linux sir5.erg.inpe.br 2.6.18-128.7.1.el5 #1 SMP Mon Aug 24 08:20:55 EDT 2009 i686 i686 i386 GNU/Linux rpm -qa | grep xorg-x11-server xorg-x11-server-utils-7.1-4.fc6 xorg-x11-server-sdk-1.1.1-48.52.el5 xorg-x11-server-Xvfb-1.1.1-48.52.el5 xorg-x11-server-Xnest-1.1.1-48.52.el5 xorg-x11-server-Xorg-1.1.1-48.52.el5 The drmOpenDevice error continues when using the suggested Option "AIGLX" "true".

    Read the article

  • Ubuntu 13.04 to 13.10: Filesystem check or mount failed [migrated]

    - by SamHuckaby
    I attempted to upgrade from Ubuntu 13.04 to 13.10 today, and mid upgrade the system started flaking out, and eventually locked up entirely. I was forced to restart the computer, and am now unable to get the computer to boot up at all. When I boot currently, it takes me to the GRUB menu, and I can choose to boot normally, or boot in an older version. I have tried several things, which I list below, but no matter what, when I try to finish booting into Ubuntu, I receive the following error: Filesystem check or mount failed. A maintenance shell will now be started. CONTROL-D will terminate this shell and continue booting after re-trying filesystems. Any further errors will be ignored root@ubuntu-computername:~# I have fun fsck -f and everything appears correct, no errors are reported. and it passes all 5 checks. If I run fdisk -l then I get the following information: Disk /dev/sda: 320.1 GB, 320072933376 bytes 255 heads, 63 sectors/track, 38913 cylinders, total 625142448 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 4096 bytes / 4096 bytes Disk identifier: 0x00010824 Device Boot Start End Blocks Id System /dev/sda1 * 2048 608456703 304227328 83 Linux /dev/sda2 608458750 625141759 8341505 5 Extended Partition 2 does not start on physical sector boundary. /dev/sda5 608458752 625141759 8341504 82 Linux swap / Solaris Disk /dev/sdb: 320.1 GB, 320072933376 bytes 255 heads, 63 sectors/track, 38913 cylinders, total 625142448 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 4096 bytes I/O size (minimum/optimal): 4096 bytes / 4096 bytes Disk identifier: 0x0fb4b7e8 Device Boot Start End Blocks Id System /dev/sdb1 8192 625139711 312565760 7 HPFS/NTFS/exFAT I am considering just installing a new OS on the other disk, that currently has nothing on it, and then just attempting to scrape my data off the old disk (thankfully I didn't encrypt the files). Really my question is this: Can I salvage this Ubuntu install, or should I give up and just reinstall?

    Read the article

  • /etc/security/limits.conf for setting program limits in Linux

    - by Flavius Akerele
    I have the following inside /etc/security/limits.conf (I have specified root separately because * will not include it.) user2 - core unlimited * - core 0 root - core 0 * - rss 512000 root - rss 512000 * - nproc 100 root - nproc 100 * - maxlogins 1 root - maxlogins 1 I run a program as user2 (./programname) but /proc/3498/limits says cores are disabled: Limit Soft Limit Hard Limit Units Max cpu time unlimited unlimited seconds Max file size unlimited unlimited bytes Max data size unlimited unlimited bytes Max stack size 8388608 unlimited bytes Max core file size 0 0 bytes Max resident set 524288000 524288000 bytes Max processes 100 100 processes Max open files 1024 1024 files Max locked memory 65536 65536 bytes Max address space unlimited unlimited bytes Max file locks unlimited unlimited locks Max pending signals 14001 14001 signals Max msgqueue size 819200 819200 bytes Max nice priority 0 0 Max realtime priority 0 0 Max realtime timeout unlimited unlimited us Both ulimit -Sa and ulimit -Ha output that cores are disabled: core file size (blocks, -c) 0 data seg size (kbytes, -d) unlimited scheduling priority (-e) 0 file size (blocks, -f) unlimited pending signals (-i) 14001 max locked memory (kbytes, -l) 64 max memory size (kbytes, -m) 512000 open files (-n) 1024 pipe size (512 bytes, -p) 8 POSIX message queues (bytes, -q) 819200 real-time priority (-r) 0 stack size (kbytes, -s) unlimited cpu time (seconds, -t) unlimited max user processes (-u) 100 virtual memory (kbytes, -v) unlimited file locks (-x) unlimited Why are cores disabled ?

    Read the article

  • Opening an existing process

    - by Grasper
    I am using Eclipse in Linux through a remote connection (xrdp). My internet got disconnected, so I got disconnected from the server while eclipse was running. Now I logged in again, and I do the "top" command I can see that eclipse is running and still under my user name. Is there some way I can bring that process back into my view (I do not want to kill it because I am in the middle of checking in a large swath of code)? It doesnt show up on the bottom panel after I logged in again. Here is the "top" output: /home/mclouti% top top - 08:32:31 up 43 days, 13:06, 29 users, load average: 0.56, 0.79, 0.82 Tasks: 447 total, 1 running, 446 sleeping, 0 stopped, 0 zombie Cpu(s): 6.0%us, 0.7%sy, 0.0%ni, 92.1%id, 1.1%wa, 0.1%hi, 0.1%si, 0.0%st Mem: 3107364k total, 2975852k used, 131512k free, 35756k buffers Swap: 2031608k total, 59860k used, 1971748k free, 817816k cached PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND 13415 mclouti 15 0 964m 333m 31m S 21.2 11.0 83:12.96 eclipse 16040 mclouti 15 0 2608 1348 888 R 0.7 0.0 0:00.12 top 31395 mclouti 15 0 29072 20m 8524 S 0.7 0.7 611:08.08 Xvnc 2583 root 20 0 898m 2652 1056 S 0.3 0.1 139:26.82 automount 28990 postgres 15 0 13564 868 304 S 0.3 0.0 26:33.36 postgres 28995 postgres 16 0 13808 1248 300 S 0.3 0.0 6:54.95 postgres 31440 mclouti 15 0 3072 1592 1036 S 0.3 0.1 6:01.54 gam_server 1 root 15 0 2072 524 496 S 0.0 0.0 0:03.00 init 2 root RT -5 0 0 0 S 0.0 0.0 0:04.53 migration/0 3 root 34 19 0 0 0 S 0.0 0.0 0:00.04 ksoftirqd/0 4 root RT -5 0 0 0 S 0.0 0.0 0:00.00 watchdog/0 5 root RT -5 0 0 0 S 0.0 0.0 0:01.72 migration/1 6 root 34 19 0 0 0 S 0.0 0.0 0:00.07 ksoftirqd/1 7 root RT -5 0 0 0 S 0.0 0.0 0:00.00 watchdog/1 8 root RT -5 0 0 0 S 0.0 0.0 0:04.33 migration/2 9 root 34 19 0 0 0 S 0.0 0.0 0:00.05 ksoftirqd/2

    Read the article

  • Creating basic, redundant gigE or IB storage network for Xen?

    - by StaringSkyward
    With only a modest budget, I want to move my 4 xen servers over to network storage -either NFS or iSCSI which will be determined based on how well it performs when we test it (we need good throughput and it must continue to work through link and switch failure tests). We may add another couple of xen servers at some point when this is done. I don't know much about the design and operation of storage networks, so would really appreciate some hints from those with experience. The budget is around $3,800 excluding the storage appliance. I am currently thinking these are my options to remain on budget: 1) Go for used infiniband hardware and aim for 10gb performance. 2) Stick with gig ethernet and buy some new switches (cisco or procurve) to create a storage-only ethernet LAN. Upgrade to 10gigE later but try to use hardware capable of it where possible to reduce upgrade costs. I have seen used, warrantied infiniband switches at reasonable prices (presumably because big companies are converging on 10gbit ethernet?) and the promise of cheap 10gb is attractive. I know nothing about IB, so here come the questions: Can I buy 2 x switches and have multiple HBAs in my xen and storage nodes to get redundancy and increased performance without complexity or expensive management software costs? If so, can you point me to some examples? Do NFS and iSCSI work just the same regardless? Is IB a sensible choice or could/should I use ethernet or FC on the same budget - I'm keen not to get boxed into a corner for future upgrades, however. For the storage I am likely to build a storage server using nexentastor with the intention that I can later add more disks, SSDs and add another server to provide a failover option at the storage level. An HP LeftHand starter SAN is also under consideration, too. Thanks in advance.

    Read the article

  • HP Pavillion DV6500 recovery disk failure

    - by Scott W
    I recently attempted to re-install Windows Vista on an HP Pavillion DV6500 using the factory recovery DVD's, but encountered a strange problem. When the recovery disk attempted to reformat the hard disk, it failed at 22%. The error message provided was not very informative, just the error code "0x400110020000 1005". A google search turned up some people with a similar problem who asserted that HP has been know to ship corrupted recovery DVDs. The recovery disk did manage to reformat the the recovery partition before failing though, so recovering from the partition is no longer an option. It would be possible to reinstall from an off-the-shelf retail copy of Vista and then pull the drivers from HP's website, but I don't have access to a copy of Vista, and it would really be outrageous to have to purchase a new OS when I have a perfectly valid license already. Thought about biting the bullet and upgrading to Windows 7, but my understanding is that without Vista installed I'd be unable to use the upgrade version, and be forced to purchase the more expensive non-upgrade retail copy (!). Can anyone suggest a possible solution to this Catch-22? I've run out of ideas.

    Read the article

  • AWS Linux EC2: yum won't run with plugins

    - by Patrick
    Short Version: yum commands on my Amazon Linux EC2 AMI only work with --noplugins. Long Version: A couple of days ago, I ran yum update at the behest of the SSH Login MoTD telling me I had updates to install. About midway through the update (specifically while updating the kernel), the update abruptly ended (79 of 138 items completed). The website I host on EC2 got weird for a few minutes, but eventually seemed to stabilize back out (maybe EC2 restarted itself?), and I didn't have further issues (other than MySQL started running out of memory, but I think that's probably unrelated to this). Today, I went to install gcc-c++ (with yum install gcc-c++). When I did, I got the following message: Loaded plugins: priorities, security, update-motd, upgrade-helper Config error: Command "updateinfo" already defined and I get that for any command I can think to run using yum. However, If I throw in the --noplugins flag, then magically it seems to work. To be clear, when I installed a different package a week ago, it worked totally correctly, so the yum update is the only thing I can think of that changed. I could find nothing on Google with regard to "updateinfo" already defined (with and without quotes). I tried running yum update --noplugins which spit out a message telling me that I should have run yum-complete-transaction instead, but proceeded to try to update something on its own. When that completed, I tried yum-complete-transaction but that gave me a message about the transactions not lining up correctly, so it removed the old transaction (Probably since I should have completed the first transaction before trying to update again, if I had known). Based on the SF question "Linux EC2 Broken Yum", I've also tried yum clean all --noplugins (fails the same with plugins) which just gives me Cleaning repos: amzn-main amzn-updates rpmforge Cleaning up everything I also tried package-cleanup --problems Loaded plugins: priorities, update-motd, upgrade-helper No Problems Found and package-cleanup --dupes Gives a lot of dupes, so I pasted them here: http://pastebin.com/VVFQEkTT instead of inline. At this point, I'm not sure what else there even is to check.

    Read the article

  • What is the latest on Microsoft Expressoin Studio licensing?

    - by DanM
    In the past, there's been an issue with Microsoft not allowing you to deactivate an Expression Studio key. Basically, you get two keys per license. If you assign both keys (say one to a desktop and one to a laptop), then you upgrade to a new machine (say you replace your laptop or upgrade some of the hardware), you have to buy a new copy of Expression Studio ($600 for Ultimate). This seems ludicrous to me, and I'm wondering if anyone knows if this policy is still in place. I can't seem to find a EULA online anywhere, so I don't know where to find this information. I know my laptop is due for replacement soon, and I want to know if I'm going to have to sink $600 into a software product I already purchased. For background, please refer to this thread on the Microsoft Expression forums: http://social.expression.microsoft.com/Forums/en-US/general/thread/da5587bc-b098-4c6a-9a56-af3608d940d0 Note that this thread is locked. Microsoft doesn't seem to want people to discuss this. This is one reason I'm posting here rather than on that site.

    Read the article

  • SBS 2011 Essentials and too many new Mac users

    - by Harry Muscle
    We currently have about 15 users on a Windows SBS 2011 Essentials Server. I've just been informed that we plan to bring aboard about 15 more users that will be using Macs. We'll be using a Mac Server to manage the 15 new Macs, however, I'm looking for advice on how to best set this all up. Ideally I would just add the 15 new Mac users to Active Directory and setup the Mac Server to authenticate against AD, unfortunately the SBS 2011 Essentials Server has a limit of 25 users, so adding these new users to AD won't work unless we upgrade the Windows server (which I'd rather avoid since it's a lot of work and a lot of money). That leaves the option of creating user accounts for these 15 Mac users on the Mac Server only. The problem that this creates though is how do I share files been Mac users and Windows users since they are now using different systems for network authentication. Any advice (short of upgrade to SBS Standard) is highly appreciated. Thanks, Harry P.S. We don't run Exchange or anything else on our server ... it's mainly used for file sharing and enforcing security via group policies.

    Read the article

  • Poor SSL performance with vsftpd

    - by petrus
    I'm trying to tweak vsftpd to achieve maximum performance for my usage: I have only one or two clients that connect to the server. File size is between ~15MB and 1GB. Typical transfer batch represent between 1 and 2GB of data. For testing purposes, I'm using a tmpfs on both sides (thus eliminating any disks bottleneck) with a single 1GB file. When SSL is disabled, performance is good, with a transfer rate at ~120MB/s (reaching the limits of gigabit networking). With SSL enabled only for control traffic (and not data traffic), performance drops at about 112MB/s, which is still within the acceptable limits. However, when SSL is enabled for data flows, the transfer speed drops dramatically: 6.7MB/s using 3DES & SHA (ssl_ciphers=DES-CBC3-SHA in vsftpd.conf) 16MB/s using DES & SHA (ssl_ciphers=DES-CBC-SHA) I didn't tested other ciphers, but from what I can see from the CPU usage during the transfer, it seems that vsftpd is only using a single cpu/core per client. While this can fit for large ftp sites with hundreds of clients, I'd like to avoid this behavior and use more ressources on the server. On a side note, if you have any ideas regarding other openssl ciphers...

    Read the article

  • Official end of support date for Internet Explorer 6 on Windows XP

    - by scunliffe
    If I read the docs on Windows Service Pack support policies, and the specific Internet Explorer lifecycle support page as well as the Wikipedia page I've deduced that: IE6 support ends/ended at: Windows 2000 Ended (date unknown) Windows XP SP0 (RTM) Ended Home: 30-Aug-2003 Pro: 30-Sep-2004 SP1 Ended Home: 11-Jul-2004 Pro: 11-Jul-2004 SP2 Home: 13-Jul-2010 Pro: 13-Jul-2010 SP3 (released: April 21, 2008) Home: ??? Pro: ??? What isn't clear is the Windows XP SP3 scenario. In "human" terms, when is the end of support for IE6 on Windows XP SP3? e.g. if there is never a Windows XP SP4... or heaven forbid, an SP4 is released. I realize this doesn't force people to upgrade etc. however I'm trying to get a "semi" official word on when IE6 moves into the "not supported" category. I'm not interested in philosophical answers e.g. "big enterprise won't upgrade but they will expect support into 2017" stuff... I just want the "clear answer" in terms of official Microsoft support.

    Read the article

  • Will Intel be releasing anymore 6-core processors soon?

    - by jasondavis
    I am about to start buying parts every week for as long as it takes me to build the best PC I can build. I am looking at the Intel i7-920 processor right now because it is about 250$ and it is a quad-core processor based on the x58 chipset I believe. From what I have read so far, intel is coming out with some 6-core processors soon that will also use the x58 chipset and will allow me to use the same motherboard and memory/ram to upgrade to a 6-core. This sounds really good to me right now. I just read that the new 6-core processor. The Core i7-980X (extreme edition) was just released which is the first 6-core processor but it is supposed to be around $1,000 so I will probably just get the i7-920 for now and then upgrade to the 6-core version when the price goes down. The motherboard I am looking at getting the GIGABYTE GA-X58A-UD5 which is around $280 at newegg.com So that is my basic plan SO far. I have not purchased any parts yet. I am just wanting to ask if this sounds like a good idea or if I should wait longer if I am wanting to eventually have a 6-core processor. Does anyone know if Intel is planning on releasing any other 6-core processor in addition to the Core i7-980X in the near future? I just want to make sure I am buying the best setup for my money if I am going all out on it, thanks for any tips/advice.

    Read the article

  • centos TCP/IP connection very slow

    - by yuli chika
    I have a VSP (centos6.1 64bit) with 4gb ram. It always runs well, but in recent few days, the server become slowly. open a small css file need 22 seconds(2kb). tested in home/office/phone with (IE,chrome,safari,firefox). see in firebug networking DNS Lookup ?4?ms Connecting ?21.18?s Sending 1?ms Waiting ?115?ms Receiving ?9?ms The connection cost 21.18 seconds I have checked all the log file, there have no error. top commond, still have free memory. top - 00:23:15 up 8 days, 3:57, 1 user, load average: 3.60, 3.42, 3.83 Tasks: 221 total, 4 running, 217 sleeping, 0 stopped, 0 zombie Cpu(s): 19.3%us, 3.2%sy, 0.0%ni, 76.1%id, 1.4%wa, 0.0%hi, 0.0%si, 0.0%st Mem: 4194304k total, 3247724k used, 946580k free, 0k buffers Swap: 0k total, 0k used, 0k free, 0k cached PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND 32357 mysql 15 0 3710m 835m 6268 S 34.5 20.4 39:14.40 mysqld 9780 apache 15 0 442m 59m 12m S 33.2 1.4 0:05.69 httpd 9842 apache 15 0 403m 26m 10m S 16.9 0.7 0:01.23 httpd 9847 apache 15 0 412m 45m 22m R 15.3 1.1 0:01.00 httpd 9834 apache 15 0 426m 46m 11m R 13.0 1.1 0:02.22 httpd 9891 apache 15 0 407m 43m 19m S 8.0 1.1 0:00.33 httpd 9845 apache 15 0 414m 51m 24m S 6.0 1.3 0:01.53 httpd 9827 apache 15 0 402m 28m 11m S 3.3 0.7 0:02.69 httpd 9768 apache 16 0 414m 51m 24m S 3.0 1.3 0:06.51 httpd 9889 root 15 0 211m 12m 8160 S 2.7 0.3 0:00.32 php 9702 apache 15 0 415m 55m 26m S 1.7 1.4 0:10.67 httpd 9844 apache 15 0 413m 47m 21m S 1.7 1.2 0:01.21 httpd 9697 apache 15 0 414m 51m 24m S 1.3 1.3 0:11.05 httpd 9778 apache 15 0 414m 53m 25m S 1.3 1.3 0:05.38 httpd 9772 apache 15 0 414m 51m 23m R 0.7 1.3 0:05.04 httpd 9823 apache 15 0 415m 50m 23m S 0.7 1.2 0:03.97 httpd 9837 apache 15 0 402m 27m 11m S 0.3 0.7 0:01.04 httpd Then, how to check where is the problem and fixed it? I haven't change and config files in these days. Thanks.

    Read the article

< Previous Page | 178 179 180 181 182 183 184 185 186 187 188 189  | Next Page >