Search Results

Search found 8760 results on 351 pages for 'enhanced for loop'.

Page 184/351 | < Previous Page | 180 181 182 183 184 185 186 187 188 189 190 191  | Next Page >

• CPU fan turns on and off repeatedly without booting

  - by rnso

  My PC has suddenly stopped starting up. On checking with case open, the CPU fan starts running when the power is turned on, but it stops after about 2-3 seconds, restarts again after about 2-3 seconds and the loop is repeated. There is no beep and nothing appears on the screen. On searching the internet, I found there could be several reasons for this. I tried removing hard-disk, CD drive, tightening connections etc but of no avial. I also tried using a new power supply but the response is the same. Where could be the problem and how can it be solved? Thanks in advance.

  Read the article

• Need to use wusa to stop endless rebooting on R2

  - by Jack

  I installed 3 updates, which after rebooting resulted in a reboot loop, never going past the "configuring your computer for windows" stage. Last known good configuration, safe mode etc make no difference (as expected). I have no system restore images available. I used dism to uninstall one of the updates, but the other two appear to be MSP patches, and so I cannot use dism to uninstall them. From what I have been reading it appears I must use wusa, however wusa does not seem to be included in WinRE. Does anyone have a suggestion of how I can access wusa to uninstall these updates, and hopefully reverse this problem?

  Read the article

• Puppet causes endless restarts of CUPS (how does one prevent this)

  - by Purfideas

  Hi! It makes sense, and is in fact suggested on this site, to have a critical file change trigger a service restart with puppet meta-parameters (such as notify or subscribe). For example: ## file definition for printers.conf file { "/etc/cups/printers.conf": [snip], source => "puppet:///module/etc/cups/printers.conf" } ## service definition for sshd service { 'cups': ensure => running, subscribe => File['/etc/cups/printers.conf'] } But in the case of CUPS, this triggers and endless loop of restarts; the logic works like this: Change puppetmaster's version of /etc/cups/printers.conf puppetmaster pushes new version to client, triggering cups restart cupsd restart insists on putting its own time stamp at the top of printers.conf, 'Written by cupsd...' This change will be seen as out of date, so after runinterval, we return to (1). Is there a way to suppress cupsd's need to time stamp the file? Or is there a puppet trick that could help here? Thanks!

  Read the article

• Dynamic Subdomains

  - by crash

  On my new site I want to have dynamic subdomains. I'm trying to make it so that the subdomains use the same web root as the main domain, all under a single CodeIgniter installation. For example, subdomain.example.com would lead to example.com/subdomain, which is actually example.com/index.php/subdomain. I've already the DNS, virtual hosts set up but I"m getting caught up on the .htaccess. The effect of the linked htaccess is that when navigating to any subdomain, it gets caught up in an infinite loop. (Error log after one request.) It's the same effect for www., which should just resolve to the main domain.

  Read the article

• Where is IIS7 redirect occuring?

  - by neildeadman

  I have a site that is set up in IIS7 and is working (although I don't understand how). The binding is www.mysite.fr on port 80. In the root of the site there are no files but several folders. The site loads fine but I don't understand how it is loading? If I go to https://www.mysite.fr/ it redirects to https://www.mysite.fr/fr/ which redirects back to https://www.mysite.fr/ So we end up in an endless loop which fails. Using fiddler it is a 301 redirect but I have no idea where this is set! I guess it might be in the website code but as I don't know which file is loaded first, I don't know where to look! Any ideas?? All other sites are working fine...

  Read the article

• mod_rewrite directory path to deeper directory

  - by DA.

  I don't usually work with LAMP and am a bit stumped getting a site working locally. The site is set up to be used via localhost: 1) http://localhost/mysite However, the way the site files are physically on the server the root is located as such: 2) /var/www/mysite/trunk/site I'm trying to figure out a way where I could type #1 but have apache actually looking for the files in #2 so that all of the asset/page links in the web application work. Is mod_rewrite the solution? If so, I'm stumped on the syntax. I have this but it won't work (due, I assume, to it causing an infinite loop) RewriteRule ^mysite/ mysite/trunk/site I have a hunch I need to sprinkle on some regex?

  Read the article

• Nginx redirect one domain to another

  - by Bob

  Hello, I have two domain's set up on my server. Domain 1 is configured with google apps so that mail.domain1.com goes to google's mail. However, I would like domain1.com to redirect to domain2.com. Currently in my nginx.conf file I had server { listen 80; server_name domain2.com .domain1.com; rewrite ^/(.*) http://domain2.com permanent; root /home/demo/apps/cjl/public; passenger_enabled on; rails_spawn_method smart; } When I did this Firefox popped up a "Redirect not configured correctly" error and said that it thought that the redirect would create a never ending loop. I'm wondering how to set this up and any help would be appreciated. Thank you!

  Read the article

• Wamp virtualhost with supporting of remote access

  - by Farid

  To cut the long story short, I've setup a Wamp server with local virtual host for domain like sample.dev, now I've bind my static IP and port 80 to my Apache and asked the client to make some changes in his hosts file and add x.x.x.x sample.dev , I've also configured my httpd virtual host like this : <VirtualHost *:80> ServerAlias sample.dev DocumentRoot 'webroot_directory' </VirtualHost> Client can reach to my web server using the direct access by ip address, but when he tries using the sample domain looks like he gets in to some infinite loop. The firewall is off too. What would be the problem?! Thanks.

  Read the article

• How to enjoy DVD on Apple iPad

  - by user44251

  I believe many people spent a sleepless night yesterday waiting for the new Apple Tablet to come, just a few days ago or perhaps longer I noticed fierce debate about it, its name, size, capacity, processor, main features, price etc. And now, they can take a long breath with the new Apple Tablet named iPad officially released on 28, January, 2010 (Beijing Time). But I know a new battle just begins. iPad, sounds somewhat like iPod and it really shares some similarities in terms of shape like smart, light and portable. It has a 9.7-inch, LED-backlit, IPS display with a remarkable precise Multi-Touch screen. And yet, at just 1.5 lbs and 0.5 inches thin, it's easy to carry and use everywhere. It can greatly facilitates your experience with the web, emails, photos and videos. Right now, it can run almost 140.000 of the apps on the Apple store. It can even run the apps you have downloaded for your iPhone or iPod touch. But so far, I haven't seen any possibility that it can work with DVD, probability there is no built-in DVD-ROM or DVD player which can play DVD directly. As Apple iPad states, the video formats supported are MPEG-4 (MP4, M4V), H.264, MOV etc and audio formats accepted are AAC, Proteceted AAC, MP3, AIFF and WAV etc, those are formats that are commonly used with iMac. This could really a hard nut to crack if you want to watch your favourite DVD on this magic Apple iPad. But don't worry, there is still way out, you just need a few steps for ripping and importing DVD movies to Apple iPad with a simple application DVD to iPad converter What's on DVD to iPad Converter for Mac DVD to iPad converter for Mac is a powerful and professional application designed for the newly released Apple iPad which can rip, convert your DVD contents to Apple iPad compatible MPEG-4 (MP4, M4V), H.264, MOV etc, and other popular file formats like AVI, WMV, MPG, MKV, VOB, 3GP, FLV etc can also be converted so that you can put on your portable devices like iPod, iPhone, iRiver, BlackBerry etc. Besides, it can also extract audio from DVD videos and save as MP3, AIFF, AAC, WAV etc. Mac DVD to iPad converter has also been enhanced that can run both on PowerPC and Intel (Snow Leopard included). It can offer versatile editing features which allows you to make your own DVD videos. For example, you can cut your DVD to whatever length you like by Trim, crop off unwanted parts from DVD clips by Crop, add special effect like Gray, Emboss and Old film to make your videos more artistic. Besides, its built-in merging feature and batch mode allows you to join several DVD clips into a single one and do batch conversion. And more features can be expected if you afford a few minutes to try.

  Read the article

• Is it possible to dynamically adjust the priority of outgoing emails?

  - by davethegr8

  This is more of a theoretical question, but is it possible to dynamically, and on an ongoing basis, adjust the priority of emails in the mail queue? For example, for all mail, set it's priority (p) to 1 (meaning send immediately). If N emails in the last M share similar or identical content, adjust the priority of this email such that it's priority is in the range [0..1] so that p is equal to 1 - N/M and other email can get sent before the similar/identical stuff. Or, if you have another idea or standard what is it? Some background: Someone put a mail() call in an infinite loop... And now we have to wait for the mail queue to catch up before anyone can send or receive mail again.

  Read the article

• How can I enforce directory space limits in a OpenVPZ system?

  - by George

  The title says it all. I have some programs on a server (centos4-openvz) that use a directory as temp directory - but pay no attention to the size it grows. I want to enforcee a limit, like this folder cannot exceed 300mb. I would use quota but OpenVZ does not support loop devices to mount a file as such. Any other solutions? (apart from scripting a periodic delete of files in the directory). Editing the application's code to implement such a functionality is not entirely out of the question - if it can be done easily and no other ways exist.. Its written in cpp - but I don't know how to implement it.

  Read the article

• How can I perform a ping every X minuts and check the response time?

  - by Profete162

  I am currently working in a big company and we have serious latency issues. This is happening in a process control system, and is unacceptable (Open a valve sometimes take 2 minuts before command start) The Network team seems very lazy and I want to check when they say "everything alright on the network". So, I want to create a loop that ping the server and write the result in a text file. I am not a batch expert, but do you think this code is correct to use? @ECHO OFF :LOOPSTART time /T ping xxx.xx.x.x -t >> filename.txt sleep -m 3000 GOTO LOOPSTART

  Read the article

• How would you measure the amount of atmospheric dust in a server room?

  - by Tom O'Connor

  We've been advised by our tape library vendor that one of the reasons we might be seeing lots of errors is if our server room is particularly dusty. It doesn't look dusty, but that's not to say it's not there. We've got an environment sensor cluster which measures Temperature, Airflow and Relative Humidity. I should probably point out that the low-hanging fruit solution I came up with is to use Sellotape (scotch tape) in a loop, one side stuck to the server cabinet, the other side free-hanging. I've also put a couple of other tape loops by the exit and intake fans of the hardware (not blocking airflow, naturally). How can we (electronically, ideally) measure dust levels?

  Read the article

• Mounting LVM2 volume with XFS filesystem

  - by Chris

  Unfortunately I'm not able to access the data on my NAS anymore. I can't figure out why this is the case as I haven't changed anything. So I plugged one of the harddisks in my computer to access the data. What I did: kpartx -a /dev/sdc Now I should be able to access /dev/mapper/vg001-lv001 When trying to mount it I get: sudo mount -t xfs /dev/mapper/vg001-lv001 /home/user/mnt mount: /dev/mapper/vg001-lv001: can't read superblock Now I did a parted -l which gave me Modell: Linux device-mapper (linear) (dm) Festplatte /dev/mapper/vg001-lv001: 498GB Sektorgröße (logisch/physisch): 512B/512B Partitionstabelle: loop Number Begin End Size Filesystem Flags 1 0,00B 498GB 498GB xfs Does anybody have a solution how to recover the data?

  Read the article

• On Ubuntu, how to design a monitor to run a process when a file is written to a directory?

  - by J G

  I want to run a process when a file is written to a directory on Ubuntu. I understand I can write a monitor to do this. (ie not an event based trigger but a 'monitor'). To implement this - other than writing a for loop of infinite duration in C that polls the directory - what steps would you take to implement this? What steps would you take to implement a monitor on Ubuntu that runs a process (another application) when a file is written to a directory? (The reason that you'd do this is the that process writing the file is under a limited set of permissions (eg tomcat6) but the executed process (an existing software package) needs root (ie to run a process in a chroot jail))

  Read the article

• Offline installer for .net 3.5 sp1 not working

  - by Tim Tom

  I download a big file of .Net 3.5 SP1 from http://download.microsoft.com/download/2/0/e/20e90413-712f-438c-988e-fdaa79a8ac3d/dotnetfx35.exe Now when I try to install it on Windows Server 2012, I get the following screenshot: What the?? When will the microsoft learn? Now this is a loop. When I try to install from Server Manager, I get installation cannot be done. It needs installation disk. Does that mean I can't install at all without the installation disk in presence?

  Read the article

• looping .mpeg dump

  - by Matt Cook

  Need to dump an MPEG2 file in a loop, either to stdout or a named pipe. This works: $ { while : ; do cat myLoop.mpg; done; } | vlc - This works on a text file containing "1234\n": $ mkfifo myPipe $ cat test.txt > myPipe & < myPipe tee -a myPipe | cat - (it correctly loops, outputting "1234" on every line). Why does the following NOT work? $ cat myLoop.mpg > myPipe & < myPipe tee -a myPipe | vlc myPipe I'm primarily interested in re-writing the first statement to remove the improper "cat myLoop.mpg" statement. Will be inputting into VLC, or into FFMPEG and then piped into VLC.

  Read the article

• MS Excel Vba/Macro equivalent in LibreCalc or OpenOfficeCalc

  - by ReggieCL

  is there an equivalent macro/vba in libre calc that does this routine; - Read/open xls files in a path and do a batch import/copy of read sheets and merge it with the current open workbook. Here's the vba I used in MS Excel. Thanks in advance Sub Consolidate_Sheets() 'Folder Path to read the xlsx files from Path = "F:\WIP2\Below 25\" filename = Dir(Path & "*.xlsx") Do While filename <> "" Workbooks.Open filename:=Path & filename, ReadOnly:=True For Each sheet In ActiveWorkbook.Sheets 'import/copy sheets from to read xlsx files sheet.Copy After:=ThisWorkbook.Sheets(1) Next sheet Workbooks(filename).Close filename = Dir() Loop End Sub

  Read the article

• User account automatically filling up with dead.letter file

  - by jeroen

  I have one user account on a server with about 400 accounts that is filling up automatically. The dead.letter file in the users home directory automatically grows until the account is full (about 10 - 40 Mb per day). The user is using Microsoft Outlook to send and receive mail. What can be causing this and how can I avoid it from happening? Right now I have an emergency cron-job to delete the file but I would like "real" solution. Edit: The server version is Red Hat Enterprise Linux ES release 4 (Nahant Update 4) Edit 2: It seems mainly spam and I see different mailer headings (from php to Outlook Express) and a frequent appearing header is [email protected].loop Update: I have asked the hosting provider where I use that dedicated server to look into the problem as well, as it's their Control Panel that could be a cause of the problem.

  Read the article

• Powershell and DfsrConfigurationFromAD - how to check all servers are updated?

  - by user57792

  I have two Win2012R2 servers (SERVER1 and SERVER2) that uses DFS Replication for keeping a couple of folders synchronized. Using the following Powershell-script that i run on SERVER1 I disconnect it from the group: Set-DfsrConnection -GroupName "Group1" -SourceComputerName "SERVER1" -DestinationComputerName "SERVER2" -DisableConnection $True; And to update both the servers with the configuration I run the command: Update-DfsrConfigurationFromAD -ComputerName "SERVER1","SERVER2" Now the question is, how can check on SERVER1 that SERVER2 has gotten the updated information from the AD so that I can be sure that the connection has been disabled? Usually it takes around 10-30 seconds after the Update-DfsrConfigurationFromAD command has been run before the DFS Management on SERVER2 gets updated but I need some kind of a "check and sleep loop" in my code. I've tried checking event logs and using Invoke-Command {Get-DfsrConnection} from PM-SERVER01 but nothing seems to work.

  Read the article

• Logical and Physical network topologies

  - by t.thielemans

  I'm trying to understand the difference between logical and physical topologies but it's a bit confusing to me. Cisco states these as logical topologies, but from my understanding these should be physical topologies? This is what I understand so far: Physical PtP: desktop directly connected to a desktop Multiaccess: several desktops connected to a medium with access to each other (Cisco Ring image, how should I view this in a live situation?) Ring: several desktops directly connected to each other creating a loop? Logical PtP: two desktops (virtually) connected to each other with intermediairy devices in between MultiAccess: (don't have a clue) Ring: (don't have a clue) Could anyone help me out and perhaps explain the difference a bit more detailed? Online I can't find any useful topics. I am using the Cisco Network Fundamentals book.

  Read the article

• Adding a MySQL StoredProcedure causes not responding state

  - by Omie

  I'm on Windows 7 ultimate 32bit + xampp 1.7.2 [MySQL v5.1.37] This is my stored procedure : delimiter // CREATE PROCEDURE updatePoints(IN parentid INT(5),IN userid INT(5)) DECLARE chpoints INT(5); BEGIN SELECT points INTO chpoints FROM quiz_challenges WHERE id = parentid; UPDATE quiz_users SET points = points + chpoints WHERE forumid=userid; END; // delimiter ; At first it was showing error 1064 while creating stored procedure. I added delimiters part and when I tried running the query from phpmyadmin, Firefox went into not responding state. After that I started Internet Explorer and tried opening my pages which use the same database, it worked fine. However, I tried opening phpmyadmin and IE went into not responding state as well. I restarted both servers. Later restarted PC. Tried again but its same behavior. So whats wrong with this tiny little code ? Am I missing something which might be causing infinite loop ? Thanks

  Read the article

• Does Apache 2.2 (windows) have any default bandwidth limit?

  - by igino manfre'

  I'm running Apache on a server in cloud (Windows server 2008 R2 on VMware, 1 Gbps of BW, http://95.110.164.61 ). I'm streaming many live DVB MPEG Transport Stream, precompressed in loop, (not flash) generated by VLC on port 640xx and then reverse proxied by Apache on port 80. The server's firewall is open for VLC and Apache on all ports. Above 1.5 Mbps the reproduction is affected by continous stop & go. Please note that if you request a stream generated by VLC directly at http://95.110.164.61:64087/mpg2_6.4 you see a correct stream, while if you request http://95.110.164.61/mpg2_6.4 you do not. I know that Flash streaming Server uses Apache to stream on port 80 (and it works). I'm not an expert with Apache, can anyone tell me if any "special" module is required to increase the bandwidth?

  Read the article

• Need to move a debian server from i686 to x86_64 architecture

  - by user64204

  I have a debian server that I need to move from one hosting provider to another. I don't really know how the old server was setup, all I know is that it's running a Ruby on Rails application with a lot of custom libraries installed and that I should prepare myself for a painful migration. Old server: -os: debian 5.0.9 -used disk space: 3.2GB -architecture: i686 New server: -os: debian 5.0.9 -free disk space: 10GB -architecture: x86_64 As you can see the problem is that the servers are running different architectures. Q: Is there anyway I could somehow migrate the old to the new server in a few steps (or am I just dreaming I could) ? I was thinking maybe I could: -get list of packages and gems installed on old server and use for loop to install them all on the new -copy the disk content from old to new server while excluding what is architecture-specific (the problem is that I don't really know what to exclude).

  Read the article

• Iterating over resources in puppet templates

  - by daveg

  So I've got a puppet manifest, with multiple resources class foo { Custom::Resource {'resource1': attr1 => 'val1', attr2 => 'val2', } Custom::Resource {'resource2': attr1 => 'val3', attr2 => 'val4', } Custom::Resource {'resource3': attr1 => 'val5', attr2 => 'val6', } } If I wanted to loop over the Custom::Resource resource names in an .erb template that are defined in class foo, how do I access them? So if I wanted to write out a template that looked like this: ThisLine = resource1 ThisLine = resource2 ThisLine = resource3

  Read the article

< Previous Page | 180 181 182 183 184 185 186 187 188 189 190 191  | Next Page >