Search Results

Search found 6636 results on 266 pages for 'jdbc driver'.

Page 186/266 | < Previous Page | 182 183 184 185 186 187 188 189 190 191 192 193  | Next Page >

  • GeForce 9600GT support for dual monitor setup

    - by Theo
    I have a NVIDIA GeForce 9600 GT (point of view, link) on an Asus M2V-MX motherboard. The card has one DVI, HDMI and S-Video output. The graphics card does not seem to support dual monitors: the driver control panel for the graphics card does not detect a second monitor that is attached via S-Video (which leads me to believe that it doesn't support dual monitors with DVI and the other connections). Would it be possible to use a VGA/DVI splitter to attach two monitors to the single DVI output on the graphics card? Would this allow for a dual monitor setup, or only mirroring? How do I know if the graphic card supports this? With this particular motherboard, would it be possible to use the onboard video for another monitor?

    Read the article

  • Why is this LTO4 Tape-drive not working

    - by Tim Haegele
    # modprobe mptsas # dmesg [ 4274.796796] scsi target7:0:0: mptsas: ioc1: delete device: fw_channel 0, fw_id 0, phy 0, sas_addr 0x50050763124b29ac [ 4274.939579] mptsas 0000:01:00.0: PCI INT A disabled [ 4280.934531] Fusion MPT SAS Host driver 3.04.12 [ 4280.934552] mptsas 0000:01:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 4280.934692] mptbase: ioc2: Initiating bringup [ 4281.490183] ioc2: LSISAS1064E B3: Capabilities={Initiator} [ 4281.490203] mptsas 0000:01:00.0: setting latency timer to 64 [ 4293.555274] scsi8 : ioc2: LSISAS1064E B3, FwRev=011e0000h, Ports=1, MaxQ=277, IRQ=16 [ 4293.574906] mptsas: ioc2: attaching ssp device: fw_channel 0, fw_id 0, phy 0, sas_addr 0x50050763124b29ac [ 4293.576471] scsi 8:0:0:0: Sequential-Access IBM ULTRIUM-HH4 B6W1 PQ: 0 ANSI: 6 [ 4293.578549] st 8:0:0:0: Attached scsi tape st0 [ 4293.578550] st 8:0:0:0: st0: try direct i/o: yes (alignment 512 B) [ 4293.578577] st 8:0:0:0: Attached scsi generic sg5 type 1 # mt -f /dev/st0 status mt -f /dev/st0 status mt: /dev/st0: rmtopen failed: Input/output error # dd if=/dev/zero of=/dev/nst0 bs=1024 count=10 dd: opening `/dev/nst0': Input/output error I am running debian squeeze 2.6.32-5-amd64 #1 SMP Sun May 6 04:00:17 UTC 2012 x86_64 GNU/Linux Server is Fujitsu TX140 with Controller Symbios Logic SAS1064ET PCI-Express Fusion-MPT SAS Tape+Hardware is new.

    Read the article

  • WHEA_UNCORRECTABLE_ERROR BSOD - what is wrong?

    - by Arcane
    Hello I have a problem with my PC getting the WHEA_UNCORRECTABLE_ERROR bsod. It is a few months old pc. I am not overclocking or changing anything in bios, but sometimes (this is my third time) I get this bsod out of nowhere. This last time I was just watching some stream on twitch when the pc suddenly crashed. I have everything up to date in windows update and every other driver as well. Everything in Open hardware Monitor seems ok. Right now as of 10 min after the crash, the CPU temp is at 38°C, fans are at 1400RPM I am using Windows 8.1 Pro 64b. Here are my spec: Intel i5-4570 CPU @ 3.20GHz, Kingston HyperX 8GB DDR3 1600 XMP, GeForce GTX 660 with 340.52 drivers, Corsair VS450 power supply, Gigabyte GA-H87-HD3 you can see the BSOD dump here: https://www.dropbox.com/s/88i1q2nnqnpzux1/082514-29656-01.dmp?dl=0 Can anybody tell me what is wrong?

    Read the article

  • Print server not being recognized after switching router and upgrading to 64 bit

    - by picardo
    I recently upgraded Windows 7 from 32 bit to 64 bit. I also switched my router from a very old model of Netgear to TP-Link. Before these updates, I had been using a USB print server by IOGear. After the updates, I took care to reinstall the drivers for both the print server and the printer, and picked the option to install a printer via TCP/IP, but no matter what I did, the driver software couldn't locate the print server on my network. I hit refresh, restarted my machine, turned off the firewalls and tried again. Still nothing. I'm at my wit's end. What else is left to try? Edit: More info. The print server is connected to the router via LAN line. The computer is connected to the router with a wireless connection.

    Read the article

  • Could not synchronize database state with session

    - by user359427
    Hello all, I'm having trouble trying to persist an entity which ID is a generated value. This entity (A), at persistence time, has to persist in cascade another entity(B). The relationship within A and B is OneToMany, and the property related in B is part of a composite key. I'm using Eclipse, JBOSS Runtime, JPA/Hibernate Here is my code: Entity A: @Entity public class Cambios implements Serializable { private static final long serialVersionUID = 1L; @SequenceGenerator(name="CAMBIOS_GEN",sequenceName="CAMBIOS_SEQ",allocationSize=1) @Id @GeneratedValue(strategy=GenerationType.SEQUENCE, generator="CAMBIOS_GEN") @Column(name="ID_CAMBIO") private Long idCambio; //bi-directional many-to-one association to ObjetosCambio @OneToMany(cascade={CascadeType.PERSIST},mappedBy="cambios") private List<ObjetosCambio> objetosCambioList; public Cambios() { } ... } Entity B: @Entity @Table(name="OBJETOS_CAMBIO") public class ObjetosCambio implements Serializable { private static final long serialVersionUID = 1L; @EmbeddedId private ObjetosCambioPK id; //bi-directional many-to-one association to Cambios @ManyToOne @JoinColumn(name="ID_CAMBIO", insertable=false, updatable=false) private Cambios cambios; //bi-directional many-to-one association to Objetos @ManyToOne @JoinColumn(name="ID_OBJETO", insertable=false, updatable=false) private Objetos objetos; public ObjetosCambio() { } ... Entity B PK: @Embeddable public class ObjetosCambioPK implements Serializable { //default serial version id, required for serializable classes. private static final long serialVersionUID = 1L; @Column(name="ID_OBJETO") private Long idObjeto; @Column(name="ID_CAMBIO") private Long idCambio; public ObjetosCambioPK() { } Client: public String generarCambio(){ ServiceLocator serviceLocator = null; try { serviceLocator = serviceLocator.getInstance(); FachadaLocal tcLocal; tcLocal = (FachadaLocal)serviceLocator.getFacadeService("java:comp/env/negocio/Fachada"); Cambios cambio = new Cambios(); Iterator it = objetosLocal.iterator(); //OBJETOSLOCAL IS ALREADY POPULATED OUTSIDE OF THIS METHOD List<ObjetosCambio> ocList = new ArrayList(); while (it.hasNext()){ Objetos objeto = (Objetos)it.next(); ObjetosCambio objetosCambio = new ObjetosCambio(); objetosCambio.setCambios(cambio); //AT THIS TIME THIS "CAMBIO" DOES NOT HAVE ITS ID, ITS SUPPOSED TO BE GENERATED AT PERSISTENCE TIME ObjetosCambioPK ocPK = new ObjetosCambioPK(); ocPK.setIdObjeto(objeto.getIdObjeto()); objetosCambio.setId(ocPK); ocList.add(objetosCambio); } cambio.setObjetosCambioList(ocList); tcLocal.persistEntity(cambio); return "exito"; } catch (NamingException e) { // TODO e.printStackTrace(); } return null; } ERROR: 15:23:25,717 WARN [JDBCExceptionReporter] SQL Error: 1400, SQLState: 23000 15:23:25,717 ERROR [JDBCExceptionReporter] ORA-01400: no se puede realizar una inserción NULL en ("CDC"."OBJETOS_CAMBIO"."ID_CAMBIO") 15:23:25,717 WARN [JDBCExceptionReporter] SQL Error: 1400, SQLState: 23000 15:23:25,717 ERROR [JDBCExceptionReporter] ORA-01400: no se puede realizar una inserción NULL en ("CDC"."OBJETOS_CAMBIO"."ID_CAMBIO") 15:23:25,717 ERROR [AbstractFlushingEventListener] Could not synchronize database state with session org.hibernate.exception.ConstraintViolationException: Could not execute JDBC batch update at org.hibernate.exception.SQLStateConverter.convert(SQLStateConverter.java:94) at org.hibernate.exception.JDBCExceptionHelper.convert(JDBCExceptionHelper.java:66) at org.hibernate.jdbc.AbstractBatcher.executeBatch(AbstractBatcher.java:275) at org.hibernate.engine.ActionQueue.executeActions(ActionQueue.java:266) at org.hibernate.engine.ActionQueue.executeActions(ActionQueue.java:167) at org.hibernate.event.def.AbstractFlushingEventListener.performExecutions(AbstractFlushingEventListener.java:321) at org.hibernate.event.def.DefaultFlushEventListener.onFlush(DefaultFlushEventListener.java:50) at org.hibernate.impl.SessionImpl.flush(SessionImpl.java:1027) at org.hibernate.impl.SessionImpl.managedFlush(SessionImpl.java:365) at org.hibernate.ejb.AbstractEntityManagerImpl$1.beforeCompletion(AbstractEntityManagerImpl.java:504) at com.arjuna.ats.internal.jta.resources.arjunacore.SynchronizationImple.beforeCompletion(SynchronizationImple.java:101) at com.arjuna.ats.arjuna.coordinator.TwoPhaseCoordinator.beforeCompletion(TwoPhaseCoordinator.java:269) at com.arjuna.ats.arjuna.coordinator.TwoPhaseCoordinator.end(TwoPhaseCoordinator.java:89) at com.arjuna.ats.arjuna.AtomicAction.commit(AtomicAction.java:177) at com.arjuna.ats.internal.jta.transaction.arjunacore.TransactionImple.commitAndDisassociate(TransactionImple.java:1423) at com.arjuna.ats.internal.jta.transaction.arjunacore.BaseTransaction.commit(BaseTransaction.java:137) at com.arjuna.ats.jbossatx.BaseTransactionManagerDelegate.commit(BaseTransactionManagerDelegate.java:75) at org.jboss.aspects.tx.TxPolicy.endTransaction(TxPolicy.java:170) at org.jboss.aspects.tx.TxPolicy.invokeInOurTx(TxPolicy.java:87) at org.jboss.aspects.tx.TxInterceptor$Required.invoke(TxInterceptor.java:190) at org.jboss.aop.joinpoint.MethodInvocation.invokeNext(MethodInvocation.java:102) at org.jboss.aspects.tx.TxPropagationInterceptor.invoke(TxPropagationInterceptor.java:76) at org.jboss.aop.joinpoint.MethodInvocation.invokeNext(MethodInvocation.java:102) at org.jboss.ejb3.tx.NullInterceptor.invoke(NullInterceptor.java:42) at org.jboss.aop.joinpoint.MethodInvocation.invokeNext(MethodInvocation.java:102) at org.jboss.ejb3.security.Ejb3AuthenticationInterceptorv2.invoke(Ejb3AuthenticationInterceptorv2.java:186) at org.jboss.aop.joinpoint.MethodInvocation.invokeNext(MethodInvocation.java:102) at org.jboss.ejb3.ENCPropagationInterceptor.invoke(ENCPropagationInterceptor.java:41) at org.jboss.aop.joinpoint.MethodInvocation.invokeNext(MethodInvocation.java:102) at org.jboss.ejb3.BlockContainerShutdownInterceptor.invoke(BlockContainerShutdownInterceptor.java:67) at org.jboss.aop.joinpoint.MethodInvocation.invokeNext(MethodInvocation.java:102) at org.jboss.aspects.currentinvocation.CurrentInvocationInterceptor.invoke(CurrentInvocationInterceptor.java:67) at org.jboss.aop.joinpoint.MethodInvocation.invokeNext(MethodInvocation.java:102) at org.jboss.ejb3.session.SessionSpecContainer.invoke(SessionSpecContainer.java:176) at org.jboss.ejb3.session.SessionSpecContainer.invoke(SessionSpecContainer.java:216) at org.jboss.ejb3.proxy.impl.handler.session.SessionProxyInvocationHandlerBase.invoke(SessionProxyInvocationHandlerBase.java:207) at org.jboss.ejb3.proxy.impl.handler.session.SessionProxyInvocationHandlerBase.invoke(SessionProxyInvocationHandlerBase.java:164) at $Proxy298.persistEntity(Unknown Source) at backing.SolicitudCambio.generarCambio(SolicitudCambio.java:521) at sun.reflect.NativeMethodAccessorImpl.invoke0(Native Method) at sun.reflect.NativeMethodAccessorImpl.invoke(Unknown Source) at sun.reflect.DelegatingMethodAccessorImpl.invoke(Unknown Source) at java.lang.reflect.Method.invoke(Unknown Source) at com.sun.faces.el.MethodBindingImpl.invoke(MethodBindingImpl.java:146) at com.sun.faces.application.ActionListenerImpl.processAction(ActionListenerImpl.java:92) at javax.faces.component.UICommand.broadcast(UICommand.java:332) at javax.faces.component.UIViewRoot.broadcastEvents(UIViewRoot.java:287) at javax.faces.component.UIViewRoot.processApplication(UIViewRoot.java:401) at com.sun.faces.lifecycle.InvokeApplicationPhase.execute(InvokeApplicationPhase.java:95) at com.sun.faces.lifecycle.LifecycleImpl.phase(LifecycleImpl.java:245) at com.sun.faces.lifecycle.LifecycleImpl.execute(LifecycleImpl.java:110) at javax.faces.webapp.FacesServlet.service(FacesServlet.java:213) at org.apache.catalina.core.ApplicationFilterChain.internalDoFilter(ApplicationFilterChain.java:290) at org.apache.catalina.core.ApplicationFilterChain.doFilter(ApplicationFilterChain.java:206) at org.apache.myfaces.webapp.filter.ExtensionsFilter.doFilter(ExtensionsFilter.java:301) at org.apache.catalina.core.ApplicationFilterChain.internalDoFilter(ApplicationFilterChain.java:235) at org.apache.catalina.core.ApplicationFilterChain.doFilter(ApplicationFilterChain.java:206) at org.jboss.web.tomcat.filters.ReplyHeaderFilter.doFilter(ReplyHeaderFilter.java:96) at org.apache.catalina.core.ApplicationFilterChain.internalDoFilter(ApplicationFilterChain.java:235) at org.apache.catalina.core.ApplicationFilterChain.doFilter(ApplicationFilterChain.java:206) at org.apache.catalina.core.StandardWrapperValve.invoke(StandardWrapperValve.java:235) at org.apache.catalina.core.StandardContextValve.invoke(StandardContextValve.java:191) at org.jboss.web.tomcat.security.SecurityAssociationValve.invoke(SecurityAssociationValve.java:190) at org.jboss.web.tomcat.security.JaccContextValve.invoke(JaccContextValve.java:92) at org.jboss.web.tomcat.security.SecurityContextEstablishmentValve.process(SecurityContextEstablishmentValve.java:126) at org.jboss.web.tomcat.security.SecurityContextEstablishmentValve.invoke(SecurityContextEstablishmentValve.java:70) at org.apache.catalina.core.StandardHostValve.invoke(StandardHostValve.java:127) at org.apache.catalina.valves.ErrorReportValve.invoke(ErrorReportValve.java:102) at org.jboss.web.tomcat.service.jca.CachedConnectionValve.invoke(CachedConnectionValve.java:158) at org.apache.catalina.core.StandardEngineValve.invoke(StandardEngineValve.java:109) at org.apache.catalina.connector.CoyoteAdapter.service(CoyoteAdapter.java:330) at org.apache.coyote.http11.Http11Processor.process(Http11Processor.java:829) at org.apache.coyote.http11.Http11Protocol$Http11ConnectionHandler.process(Http11Protocol.java:598) at org.apache.tomcat.util.net.JIoEndpoint$Worker.run(JIoEndpoint.java:447) at java.lang.Thread.run(Unknown Source) Caused by: java.sql.BatchUpdateException: ORA-01400: no se puede realizar una inserción NULL en ("CDC"."OBJETOS_CAMBIO"."ID_CAMBIO") Thanks in advance! JM.-

    Read the article

  • Can't set 1280x1024 on Ubuntu with Nvidia Geforce 8400 GS

    - by torbengb
    Ubuntu doesn't offer 1280x1024 but that's what my monitor has -- I want to set that resolution but need help doing so. Ubuntu offers 1360x768, 1152x864, 1024x768 when using the Nvidia driver version 180. This is Ubuntu 9.04 installed as "Wubi" through Windows, I believe it's the amd64 version. Google gave me this precise explanation which is complete latin to me; I'm a Windows guy and not familiar with Terminal. These SU questions also don't provide answers, hence this new question. I hope you can help, and I will provide additional info if required.

    Read the article

  • WinXP How to Tunnel LPT over USB

    - by Michael Pruitt
    I have a windows program that accesses a device connected to a LPT (1-3) 25 pin port. The communication is bidirectional, and I suspected the control lines are also accessed directly. I would like to migrate the device to a machine that does not have a LPT port. I saw the dos2usb software, but that takes the output (from a DOS program) and 'prints' it formatted for a specific printer. I need a raw LPT connection, and a cable that provides access to all the control signals. I do have a USB to 36-pin Centronics that may have the extra signals. I use it with a vinyl cutter that doesn't like most of the USB dongles. It comes up as USB001. Would adding and sharing a generic printer, then mapping LPT1 to the share get me closer? Would that work for a parallel port scanner? My preferred solution is a USB cable with a driver that will map it to LPT1, LPT2, or LPT3.

    Read the article

  • Lenovo DVD Drive Disabled After Windows 7 Install

    - by David Lacher
    Upgraded hard drive in Lenovo T61P; decided to start fresh with Windows 7 Pro. Windows installed, so DVD drive was working. All of a sudden, driver is not recognized. Device is "HL-DT-ST DVDRAM GSA-U10N ATA Device". It appears on device manager but with the yellow tag; have tried uninstalling, searching for drivers, everything I can think of. Cannot even start over with Windows 7 installation disk because disk spins but then stops and My Computer does not recognize the drive. Help please. thank you. David Lacher

    Read the article

  • How to tell X.org to reload input device module?

    - by Vi
    When X.org boots up, Synaptics touchpad works well. But when I remove the module it falls back to /dev/input/mice and don't use normal driver even when touchpad is available again. Xorg.0.log: ... (II) XINPUT: Adding extended input device "Synaptics Touchpad" (type: TOUCHPAD) (--) Synaptics Touchpad: touchpad found # { rmmod psmouse && echo mem /sys/power/state && modprobe psmouse; } (WW) : No Device specified, looking for one... (II) : Setting Device option to "/dev/input/mice" ... How to tell X.org to try it's InputDevice again (without restarting X server)? P.S. rmmod psmouse is needed to prevent crashing of Acer Extensa 5220 when resuming from suspend-to-ram. Update: Found answer myself: Doing xinput set-int-prop "Synaptics Touchpad" "Device Enabled" 8 1 after reloading the kernel module reloads touchpad. Now suspend-to-ram works OK.

    Read the article

  • How to tell X.org to reload input device module? (Working around suspend-to-ram crash on Acer laptop

    - by Vi
    When X.org boots up, Synaptics touchpad works well. But when I remove the module it falls back to /dev/input/mice and don't use normal driver even when touchpad is available again. Xorg.0.log: ... (II) XINPUT: Adding extended input device "Synaptics Touchpad" (type: TOUCHPAD) (--) Synaptics Touchpad: touchpad found # { rmmod psmouse && echo mem /sys/power/state && modprobe psmouse; } (WW) : No Device specified, looking for one... (II) : Setting Device option to "/dev/input/mice" ... How to tell X.org to try it's InputDevice again (without restarting X server)? P.S. rmmod psmouse is needed to prevent crashing of Acer Extensa 5220 when resuming from suspend-to-ram. Update: Found answer myself: Doing xinput set-int-prop "Synaptics Touchpad" "Device Enabled" 8 1 after reloading the kernel module reloads touchpad. Now suspend-to-ram works OK.

    Read the article

  • Cant connect to MySQL server from Java application

    - by RN
    This is on VPS\Centos server. The MySQL server is pre configured. I am running the Java application on Tomcat My Java web application is not able to connect to the MySQL server. I get an error - "Caused by: java.net.ConnectException: Connection refused" I suspect this to be a configuration problem rather than a coding problem- hence I have posted this on ServerFault And yes, The same web-app is able to connect to MySQL on a different linux box This is the URL that I provided to my Java application (note- it assumes default port) url = "jdbc:mysql://localhost/pickupgames" My first suspicion was that I am running on a non-default port So I tried to find the port where mySQL server is running I tried every trick mentioned in http://serverfault.com/questions/116100/how-to-check-what-port-mysql-is-running-on But no luck ! SHOW GLOBAL VARIABLES LIKE 'PORT'; This shows port 0 netstat -tlnp doesn't show mysql at all /etc/my.cnf It has no port entry telnet localhost 3306 Doesn't connect And in case you are wondering if mysql server is running at all or not It is And I know for sure, because I have been able to login using the mysql command Also # ps -ef|grep 'mysql' root 31839 27662 0 00:49 pts/3 00:00:00 grep mysql root 32452 1 0 Apr02 ? 00:00:00 /bin/sh /usr/bin/mysqld_safe --skip-grant-tables --skip-networking mysql 32504 32452 0 Apr02 ? 00:00:06 /usr/libexec/mysqld --basedir=/usr --datadir=/var/lib/mysql --user=mysql --pid-file=/var/run/mysqld/mysqld.pid --skip-external-locking --socket=/var/lib/mysql/mysql.sock --skip-grant-tables --skip-networking Please note the --skip-networking parameter Does this have something to do with the issue ? Any explanation why I cant connect to mysql server on port 3306 by telnet? Or why it docent show up under netstat? Any suggestion on whet I should try next ?

    Read the article

  • Lenovo DVD Drive Disabled After Windows 7 Install

    - by David Lacher
    Upgraded hard drive in Lenovo T61P; decided to start fresh with Windows 7 Pro. Windows installed, so DVD drive was working. All of a sudden, driver is not recognized. Device is "HL-DT-ST DVDRAM GSA-U10N ATA Device". It appears on device manager but with the yellow tag; have tried uninstalling, searching for drivers, everything I can think of. Cannot even start over with Windows 7 installation disk because disk spins but then stops and My Computer does not recognize the drive. Help please. thank you. David Lacher

    Read the article

  • Windows-Server-2003 setup on Dell-PowerEdge R310 is hanging [closed]

    - by Robert Rose
    Possible Duplicate: Problems installing OS on Dell PowerEdge R410 I am trying to configure a Dell PowerEdge R310 server with Windows Server 2003. I've already configured the two hard drives as RAID1. The HD controller is PERC H700 Integrated and Adapter. Trying to stay with Windows Server 2003 on this fairly new server to save on cost and keep the configuration the same as my old server, which has been running like a champ for five years. Problem: During the OS installation, after everything has been copied from the installation CD, the installation hangs at a window labeled 'Windows Setup' with the message 'Setup is starting Windows' at the bottom. I'm wondering if this is a driver problem and if so, where can I get the drivers for the R310 or where can I get the media for the latest version of Windows Server 2003 which may include the necessary drivers? Will certainly appreciate some help here.

    Read the article

  • eSATA hotswap using Jmicron JMB363 controller

    - by Stephen
    I have tried both IDE and AHCI modes in the BIOS. Also tried many different driver revisions. I can't seem to hot swap an external SATA drive. I can use the wizard to safely remove it, but reconnecting doesn't do anything unless I reboot. I use a thermaltake dock, and I would like to swap in my backup drive sometimes to do images (they take all day over USB). I can reboot, but I'd like to use hot swap. The controller is a Jmicron JMB363. I'm using the latest BIOS on my motherboard, as well.

    Read the article

  • How to debug xsane "no devices available" error on 64 bit Ubuntu 10.04

    - by BD at Rivenhill
    I have a Brother MFC-J615W printer/scanner and I wish to use the scanning feature across a network with a computer running 64-bit Ubuntu 10.04. I have installed the drivers from the Brother website and followed all of the instructions, and printing works fine, but xsane (installed from repositories) produces a popup with the message "no devices available" on startup. I recently had success with a similar approach when installing drivers for a Brother MFC-495CW on 32-bit Unbuntu 9.10, so I am aware of issues such as requiring root access if the driver permissions are not set correctly, but running xsane as root does not solve this problem. Are there any tools available to debug this problem further or does anyone have advice on how to proceed?

    Read the article

  • NIC models for HVM guests in Xen 4.0

    - by Jed Daniels
    Is there a list of NIC models that I should use with various HVM guests in Xen 4.0? Is there even a list of possible choices for the model=field? I'm planning on running both Windows and FreeBSD guests on the particular Xen box that I'm configuring now, and ideally I'd like a setting that can work on both of them and get me gigabit speeds without a lot of extra hassle loading special drivers (similar to VMware's e1000 NIC option). Any suggestions? The vif line I'm currently using in my config is: vif = [ 'type=ioemu,bridge=eth0,model=ne2k_pci,script=vif-ovs' ] This works in my Windows XP SP3 VM, but is only recognized as a 10Mbit interface. Changing to model=e1000 or model=i82557b resulted in Windows not being able to find a driver for the NIC.

    Read the article

  • List all devices of system

    - by pareshverma91
    In my understanding linux can list only those devices which it can understand, i.e. for which the drivers have been installed. I think lspci is the command for that. But how can one figure out if there exists some device in the system for which the drivers are not installed and perhaps some hint about what that device is for and what driver would suffice for it. I would like to know this info so as to be able to recompile my linux kernel to a minimum and would like to avoid a hit and trial approach.

    Read the article

  • Horizontal scrolling not working in Windows 7 running on MBP using Boot Camp

    - by Rubicon
    Is there a way to enable horizontal scrolling on Windows installed on a bootcamp partition of MBP 13" Core 2 Duo, using a trackpad? I had a look into the Boot Camp Control panel settings, but could not find a setting that suggested this. I used the Boot Camp drivers that came with the MBP in the Mac OS X Install disk. The vertical scroll is working fine, and the horizontal scroll works fine in the Mac world of things, so the hardware is fine. I think maybe there might be an additional install for a driver that we may have to install? Or any update? Thanks in advance for all your help. :)

    Read the article

  • Why do my speakers get distorted randomly on Windows 7?

    - by Daniel Fischer
    I have a studio monitor setup. I have 2 KRK 6's and a Focusrite Firewire Pro 24. Every few hours my speakers sound distorted and my solution has been go to sound levels Properties of Saffire Audio Device Advanced Default Format Toggle to 16 bit then back to 24bit. Why does it screw up every few hours? Sometimes one speaker doesn't output too and this same process resets it but that's more rare. Is this a OS issue or Focusrite Driver Issue?

    Read the article

  • NIC interface names in /proc/interrupts

    - by Gallus
    When I look at /proc/interrupts: $ cat /proc/interrupts CPU0 CPU1 (...) 12: 4 0 IO-APIC-edge i8042 14: 145 65310875 IO-APIC-edge ide0 50: 0 0 IO-APIC-level uhci_hcd:usb5, Intel ICH7 58: 5388 7983508 IO-APIC-level libata 169: 812427252 1236572641 IO-APIC-level skge, eth1 217: 6 0 IO-APIC-level ehci_hcd:usb1, uhci_hcd:usb2 225: 0 0 IO-APIC-level uhci_hcd:usb3 233: 60 3108720778 IO-APIC-level uhci_hcd:usb4, skge I can see two skge and one eth1 entries. All of them are the network cards. Because of the general name "skge" (which is the name of the network driver of the card) I can't easily reocognize, which NIC occupies which interrupt. How to make linux use more descriptive names in the entries? Or: Is there any alternative way to obtain INT information instead of /proc/interrupt? My final goal is to manipulate smp_affinities of the NICs.

    Read the article

  • HP Color LaserJet 2605dn color alignment issue

    - by robertvt
    We have a HP Color LaserJet 2605dn at work that recently lost its mind. The red and blue colors are offset from where they should be and producing a rather trippy 3D look. I've performed a manual calibration through the menus and poked at just about everything I could find. These toner cartridges are not new (as you can see they're about 50% used) but only just recently started this problem. They were working great up until this error appeared. It happens on mac, pc, and via the printer menu printouts so I don't think it's a driver problem. The printer has been restarted and reset and is running the newest firmware. Anyone have any ideas? Here's a pic http://img16.imageshack.us/img16/9984/photoon20090914at1149.jpg

    Read the article

  • Delay between printing via lp in opensuse

    - by adamweeks
    I am experiencing a 10-15 second delay when printing multiple documents to a barcode printer in opensuse. I have had the same setup on other systems with older versions of opensuse without any issue. The setup is as follows: The print queue is setup as a "generic with driver Raw Queue". The files being sent down to the printers are simple text files with the lp command: lp -dprinter1 /path/file The printer is a JetDirect compatible device (Intermec brand) with a standard 9100 port socket setup. If I send a multi-page document to the printer, it will print nonstop the multiple pages. If I send 2 or more text files down via separate "lp" commands, the delay will be there between each printout. I've tried multiple different printers and they all experience the same issue.

    Read the article

  • No sound on Debian unstable Intel Corporation 82801JD/DO (ICH10 Family) HD Audio Controller

    - by Dave Roger
    I have no sound on my Debian unstable. # cat /etc/issue Debian GNU/Linux squeeze/sid # lspci |grep -i audio 00:1b.0 Audio device: Intel Corporation 82801JD/DO (ICH10 Family) HD Audio Controller (rev 02) # lsmod | grep -i snd snd_hda_codec_realtek 235506 1 snd_hda_intel 19907 0 snd_hda_codec 54244 2 snd_hda_codec_realtek,snd_hda_intel snd_hwdep 5380 1 snd_hda_codec snd_pcm_oss 32591 0 snd_mixer_oss 12606 1 snd_pcm_oss snd_pcm 60471 3 snd_hda_intel,snd_hda_codec,snd_pcm_oss snd_seq_midi 4400 0 snd_rawmidi 15515 1 snd_seq_midi snd_seq_midi_event 4628 1 snd_seq_midi snd_seq 42881 2 snd_seq_midi,snd_seq_midi_event snd_timer 15582 2 snd_pcm,snd_seq snd_seq_device 4493 3 snd_seq_midi,snd_rawmidi,snd_seq snd 46446 11 snd_hda_codec_realtek,snd_hda_intel,snd_hda_codec,snd_hwdep,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_rawmidi,snd_seq,snd_timer,snd_seq_device soundcore 4598 1 snd snd_page_alloc 6249 2 snd_hda_intel,snd_pcm # cat /proc/asound/version Advanced Linux Sound Architecture Driver Version 1.0.21. # uname -r 2.6.32-5-amd64

    Read the article

  • no display on tv when connecting pc via hdmi in win7

    - by Kane
    The system of pc is win7 32bit, the video card is ATI 4670. The tv is philips 74xx series. And the monitor is Dell 19' that connect with pc via VGA. The tv can receive the singal and show the pictures when booting the pc(bios self checking, the logo of windows 7), however the tv says there is no signal after the win7 login window shows. I have installed the latest CCC and driver of ATI video card. Does anyone have idea for it?

    Read the article

  • Can't get Intel drivers for ASUS P6T Deluxe

    - by Alex K
    Hi everybody, A few days back my Win7 Ultimate started bugging me to install the RAID drivers for my ASUS P6T Delux. Fine, I'm all for having up to date drivers even for stuff I don't use. The problem is that the drivers I download from both ASUS support site here and the ones I get directly from Intel (can't post the second link, since I have less than 10 rep, but it's the first hit for "Intel(R) Matrix Storage Manager Driver" on google) say that my system does not meet the minimum system requirements. Impossible, I would think, what with it having the X58 chipset and the Windows version is supported one. Has anyone encountered something like this before? Any clues on how to solve this would be much appreciated. Thanks!

    Read the article

< Previous Page | 182 183 184 185 186 187 188 189 190 191 192 193  | Next Page >