Search Results

Search found 17688 results on 708 pages for 'protect computer'.

Page 187/708 | < Previous Page | 183 184 185 186 187 188 189 190 191 192 193 194  | Next Page >

  • Best usage for a laptop being used as a desktop without removable batteries

    - by Senseful
    After reading the information on http://batteryuniversity.com, I realize that one of the best ways to permanently damage a lithium ion battery is to use the battery at a high temperature while it's fully charged. This is exactly what happens when you use the computer as if it were a desktop computer, since leaving it plugged in will keep the battery at 100% and using the computer will heat up the battery. This is why it's recommend to remove the battery from your laptop if you are using it is this scenario. My question is what would you do if the laptop doesn't have removable batteries (e.g. a MacBook Pro)? Should I use some kind of charge cycle such as: charge to 80%, unplug the power chord, use the laptop until it reaches 20%, then repeat the cycle by charging to 80% again? If so, which values should I use instead of 80% and 20%? (I think charging to 80% is better than 100% because of the damage that a hot battery at 100% can do, but I just made the figure 80% up, and I'm sure there's a better number to strive for which is backed by science.) I've read many of the articles on batteryuniversity.com, but couldn't find anything pertaining to this. Update: What about doing something like charge (or discharge) it to 50%, then plug it in and turn on settings which use the battery as much as possible (e.g. brightness all the way up, wi-fi on, etc.), in order to try to maintain the battery at 50% (i.e. the rate it is charging is the same as it is discharging). This will probably heat up the battery, but would make it so you don't need to constantly plug and unplug the laptop. The one bad thing is that you are taking up more charge cycles which would decrease the battery life, thus I'm not sure this is a good idea.

    Read the article

  • Why we can change our IP address?

    - by iamstupid
    I across some websites that offer change of our IP addresses. It says, we can surf net anonymously, including changing our IP address and location. Most of the softwares are not free, so I have not try it out yet. But my question is, so, IP addresses will no longer be unique or valid for identify which computer were sending/request the information? I though only the ISP can determine our IP, so we can change our IP from some commercial softwares huh? Case: If I change my IP address, I go to a website which is supposed to be banned by my country, will the ISP let me pass the check and I will be able to browse the website which should be blocked? another question: From what I know, if we want to go to certain website, here is the flow: My Computer = ISP = Website = ISP = My computer I am not sure, if its the correct flow, but I am sure that, whichever website I want to visit, I need to go through my ISP, isnt it?. So if we change out IP, our ISP will record our new IP or the original(assigned-by-ISP) IP? Sorry for my bad English.

    Read the article

  • Self-connecting printers

    - by Martin Cerny
    Hello, I work as an administrator in a small company using XP Professional on all computers and two servers with Win 2003 Server. Recently a very unusual problam occured one of the computers keeps connecting to all the printers on the network it doesn't matter if it's an administrator or Domain User as soon as somebody logs in the commputer connects all the printers. The printers are either installed on local computers or on the server and shared. There is no log-on script connecting the printers, I install them manualy and none of the other computers shows such behaviour. We have a printer which is installed on two computers and both of them share it (I'm moving it to Server from a small PC which shared it up to now, but some computers still use the old connection), meaning this specific computer connects to one of the printer two times and it can't use either of the connections. How to prevent this self-connecting to all printers (none of the other computers has this problem). If I delte them from the "Printers" folder everything works fine untill I reconnect and the Folder is once again full of all the printers we have. I solved the smaller problem, computer is now capable of printing on all of the printers (it seems there have been some registry issues), after cleaning the registry and reinstalling the printer it seems to work just fine. But the second thing prevails, the computer connects to all the printers in the network (when I remove one/multiple it is reconnected right after the next log-in by any user).

    Read the article

  • Vista won't boot. BSOD: Page fault in nonpaged area

    - by user31576
    Here's the story: I let Windows Update do the updates it wanted to do, then rebooted the computer. The updating process was taking time so I went away. When I came back, my computer was rebooting. It got as far as the Windows logo with the laoding bar. BSOD'd. Rebooted. And I'm stuck in this loop ever since. Looked up on the net, the "Page fault in nonpaged area" seems to be linked to faulty RAM or drivers. So I ran a memory test, it found no error. When I try in safe mode (with promt) I can see a list of drivers being loaded, then I get the same BSOD. I tried to repair using the Vista DVD, it says "nothing to repair". I tried to restore to a previous state, it says "no restore point found". So, my guess is, it's got something to do with the drivers. How can I identify the one causing the BSOD? If you have any other leads, What can I do? By the way, I'm writing from this very computer, running a linux distro I installed after the BSOD loop started. So i guess it's not an hardware issue. I have backed up important data, and will format and reinstall Windows if I must. But I'd like to avoid that. Thanks in advance for any help you can give me.

    Read the article

  • Certificate enrollment request chain not trusted

    - by makerofthings7
    I am working on a MSFT lab for Direct Access, and need to create a Web certificate. The instructions ask be to do the following: On EDGE1, click Start, type mmc, and then press ENTER. Click Yes at the User Account Control prompt. Click File, and then click Add/Remove Snap-ins. Click Certificates, click Add, click Computer account, click Next, select Local computer, click Finish, and then click OK. In the console tree of the Certificates snap-in, open Certificates (Local Computer)\Personal\Certificates. Right-click Certificates, point to All Tasks, and then click Request New Certificate. Click Next twice. On the Request Certificates page, click Web Server, and then click More information is required to enroll for this certificate. On the Subject tab of the Certificate Properties dialog box, in Subject name, for Type, select Common Name. In Value, type edge1.contoso.com, and then click Add. Click OK, click Enroll, and then click Finish. In the details pane of the Certificates snap-in, verify that a new certificate with the name edge1.contoso.com was enrolled with Intended Purposes of Server Authentication. Right-click the certificate, and then click Properties. In Friendly Name, type IP-HTTPS Certificate, and then click OK. Close the console window. If you are prompted to save settings, click No. In production, our company has overridden the Web Server template and it doesn't seem to be issuing certificates with the full CA chain. When I look at the issued certificate properties then both tiers of the 2 tier CA hierarchy are missing. How can I fix this? I'm not sure where to look outside the GUI.

    Read the article

  • Insertion of rows without changing formulas on anohter sheets

    - by julie
    I have two separate spreadsheets which feed each other (one person completes the main one so all others autofill). I have set up formulas so it autofills but when I insert new lines into the main spreadsheet the other spreadsheet takes information from the wrong line, even though the new data was put in the place of the old data. (The new inserted lines were put in where the data was before). can anyone help me to "protect" the formulas from movement? I will appreciate any help.

    Read the article

  • How to kill tasks in Windows 7 when even Task Manager won't open or respond?

    - by endolith
    Occasionally one of my computers will get so bogged down that everything locks up, Ctrl+Alt+Del doesn't work, Task Manager won't open, or they work, but are opening so slowly that it will take hours or days to shut down other processes and regain control of the computer, etc. Is there a way to, for instance, force Task Manager to be highest priority so it always opens immediately with Ctrl+Shift+Esc even when some other process/driver is hogging the CPU? Is there some other program that can run in the background and open immediately like this? This question isn't about fixing "underlying problems". No matter how much memory you have, it's still possible for a rogue process to eat it all up and lock up the computer in page fault thrashing, hog the CPU, etc. This question is about how to take back control of the computer when that happens. Basically when these kind of lock-ups happen, I want to open some kind of task manager that pauses every other process and allows me to kill one of them, and then let everything resume so I can save my work, etc. Otherwise my only option is to hold down the power button. Antifreeze is supposed to do exactly what i want, pausing all other applications and starting a task manager to kill the offender, but in my testing, it actually does neither.

    Read the article

  • Excel 2010 Delete Rows with Locked Cells

    - by Roger
    I have a spreadsheet that has formulas that I want to lock, once the information in the row is completed, i.e. there is a discharge date, I want the end-user to be able to delete the row and insert it into another worksheet. I do not want to use VBA, I was successful in sequencing the protection steps, but now can not repeat the process. There has to be a way to use the protect sheet "delete rows" check box and locked cells together to enable this process

    Read the article

  • MacBook Air Keeps dropping Wi-Fi

    - by Robert Patrick
    So my MacBook Air keeps dropping Wi-Fi for some reason. It happens ONLY on my home network, and ONLY to my computer. I'm using a Linksys WRT54G router. I'm the only Mac on the network. Every other Wi-Fi network is perfectly fine, and every other computer on this network is fine. Many things can happen. It could say it's connected, but not be able to access the internet (whether it tells me that there's no internet access or not). It may just drop Wi-Fi altogether, and refuse to connect. Generally, if I unplug the router and plug it back in, it's all good. It also works if I restart my computer. This happens multiple times a day. Yesterday I did everything I know to get it to connect (restart router many times, restart my MacBook), and nothing worked. Eventually it just magically worked. How can I stop this from happening? We got a notice from Comcast a while ago saying that a bot called DNS Changer was detected on one or more machines on the network. I'm assuming that this can't be me, right?

    Read the article

  • Lenovo System Update Breaks Windows Live

    - by wolfvilleian
    Hey everyone, I've been racking my brain (and fingers from typing) trying to solve this issue to no avail. I have a Lenovo computer and I install their system update tool to install all my missing drivers. However after this tool is installed Windows Live 2011 breaks, it will no longer sign in giving error number 8e5e0247 all the solutions online haven't helped. It appears that a language setting somewhere gets set to en_ms, and I'm en_ca. My computer is running Windows 7 x64. When i try to sign onto messenger it gives an error that (with some research) means your locale or language is not supported, I've searched my computer for any reference to en_ms but find none. Also a few other things seem to have broken, When a UAC box comes up it is no longer able to identify the publisher of anything, and also the indexing service does not work (I'm not sure if the indexing issue is related, but the UAC issue happened right after installation), I had this issue before but I don't remember how I fixed it, I believe it had something to do with environmental variables. When it goes to sign in it gets as far as the "Loading contacts" then stops and goes back to the sign in screen. Has anyone seen this before? Thanks

    Read the article

  • Sharing svn reposities between web servers

    - by Luke
    I have my subversion hosting set up to be accessed through Apache web server. Everything runs fine. Now I'd like to add another web server to distribute the load between two web servers. Is it save to have my svn repositories accessed by two web servers at the same time? Does the normal fsfs subversion repository type protect me enough or do I need to switch to Berkely DB for this sort of thing?

    Read the article

  • How to restart boot Windows 7 after upgrading to a SSHD on SONY VAIO with recovery discs?

    - by Boris Okun
    The original HDD on my Sony VAIO still works, but has a damaged sector 0 and I was constantly prompted to replace the HDD because of the imminent failure. I created recovery discs as instructed, used a USB external HDD for complete back up (including Windows image back up). After installing the SSHD and using recovery discs to upload Windows and boot, I am getting the Windows welcome screen. Right after that, I'm getting the following message: Windows couldn't complete the installation. To install Windows on this computer, restart the installation. I have tried repeating the process many times all kinds of different ways and I still receive the same message. Also, when I tried to change to partitioning as the other option offered, I get the message: Windows Setup could not configure Windows to run on this computer's hardware. All troubleshooting for hardware and PCU came out solid. I tried to load the image back up from the external drive, but can't load the driver. The computer doesn't see it. Does anyone have a clue or has encountered something similar?

    Read the article

  • Client unable to access OWA website after temporarily changing SSL certificate on the server

    - by Lorenz Meyer
    I have the following issue: One client computer (Windows XP) cannot access the OWA website. All other client computers can (Except another one in the same remote office). How this happened: I temporarily changed the SSL certificate on the Exchange Server yesterday. After a few minutes, I reverted back, an now the same certificate that was installed for years is back again. During these few minutes, they were in OWA on this computer and got a certificate error. What exactly happens: Internet Explorer displays the error Internet Explorer cannot display the webpage, Firefox displays The connection was reset and Crome shows This webpage is not available. The connection to ... was interrupted. What I already did to try to get this working: Restart the client computer Restart the exchange server Deleted Internet Explorer browsing history In IE, Internet Options, tab Content, under Certificates deletes SSL cache Restored Internet Explorer to the default parameters I looked into certmgr.msc, but did not find a certificate related to the issue What could I do else to narrow down the origin of this problem (or better: resolve it) ? Can you give any advice ?

    Read the article

  • Windows 7 - All Icons Missing, Explorer Progress Bar Never Finishes, Libraries Gone

    - by Alex
    since yesterday i've had three issues which all arose at the same time. windows 7 x64, i7 2.8ghz 12gb ddr3 1 - my libraries, favorites, drives are missing...basically the entire sidebar is gone. http://i.imgur.com/m8pRQ.png. yet when i open a dialog, my libraries and drives are back to normal ONLY for the dialog. i tried Restore Default Libraries. it works one time, but when i open libraries again i go back to the empty mess. restarting the computer temporarily fixes the problem. 2 - in the explorer window that's showing libraries, when i navigate to a certain folder i get an unending progress bar (the kind that turns the address bar green). yesterday when the problem started, i was saving a file to this folder. the program writing the file crashed during the write and i believe that's what caused the problem. i have sugarsync backing up that folder and when i restarted the computer sugarsync informed me that its database was corrupted, so i had to uninstall and reinstall the software. 3 - icons are missing. the Rebuild Icon Cache did not fix this. http://i.imgur.com/r9pgo.png restarting the computer temporarily fixes these problems, but when i open the directory with the initial write problem, everything stops working. edit: i should note that i did a chkdsk /f and it repaired problems. i also did the thing that verifies then restores windows files (can't remember the command now), which reported that everything was normal.

    Read the article

  • Fedora installed in Legacy mode, how to make it work in UEFI?

    - by TryntaLearn
    I am trying to install a linux distribution on my new laptop. It's an MSI GE40 which comes preinstalled with windows 8. It's a UEFI machine. I have tried installing Ubuntu and Fedora with limited success. I've tried: running it in UEFI, UEFI with CSM mode, with secureboot enabled, ... with secureboot disabeled, ... with secureboot enabled but in user mode. I have had no success with any of these methods. With Ubuntu the grub loader shows up, but when I pick 'try ubuntu', or 'install ubuntu', it's just a blank screen(I've been using liveusb's btw). With Fedora, it'll show me the next screen on which it says 'binary authorised by vendor certificate' or 'Secure boot not enabled' and then stop doing anything. The closest thing to success I reached was switching to legacy mode to install Ubuntu, in which case I was able to get to the ubunutu installer but it wouldn't recognize windows 8 on my computer, so instead of continuing on I rebooted, and removed the USB pendrive to find my computer couldn't find windows 8. After a little dicking about I got it to find windows 8 again. Any ideas on how I should go about trying to install a distro on my computer? UPDATE:- So I ended up installing fedora using Legacy mode. To use both it and Windows at boot, I manually enter automatic repair so I can get to my UEFI settings and switch boot mode to UEFI to boot windows 8. I guess my question needs to be modified as to how do I get all of this to work in UEFI mode, so I can dual boot via selection through a bootloader, and not by repeatedly switching boot mode.

    Read the article

  • Office 2003 Service Pack 3- Not able to install

    - by kabirrao
    I am trying to install Office 2003 SP3 on a windows 2003 EE server (used as a terminal server) which already have office 2003 SP2. I am getting an error that says "Update can not be applied". Below are the eventviewer entries for Application: _ Event Type: Warning Event Source: MsiInstaller Event Category: None Event ID: 1015 Date: 1-2-2010 Time: 5:51:22 User: Domain\domainadmin Computer: TER01 Description: Failed to connect to server. Error: 0x800401F0 For more information, see Help and Support Center at http://go.microsoft.com/fwlink/events.asp. _ Event Type: Information Event Source: MsiInstaller Event Category: None Event ID: 11708 Date: 1-2-2010 Time: 5:52:23 User: Domain\domainadmin Computer: TER01 Description: Product: Microsoft Office Professional Edition 2003 -- Installation failed. For more information, see Help and Support Center at http://go.microsoft.com/fwlink/events.asp. Data: 0000: 7b 39 30 31 31 30 34 30 {9011040 0008: 39 2d 36 30 30 30 2d 31 9-6000-1 0010: 31 44 33 2d 38 43 46 45 1D3-8CFE 0018: 2d 30 31 35 30 30 34 38 -0150048 0020: 33 38 33 43 39 7d 383C9} _ Event Type: Information Event Source: McLogEvent Event Category: None Event ID: 257 Date: 1-2-2010 Time: 5:52:23 User: NT AUTHORITY\SYSTEM Computer: TER01 Description: Would be blocked by access protection rule (rule is in warn-only mode) (Common Standard Protection:Prevent common programs from running files from the Temp folder).

    Read the article

  • Trouble in Team Viewer VPN Connection

    - by Sumit Pal
    I have completed initial vpn connection setup. It has connected. I have tested with ping and it is ok. My problem is, when I want to start file transfer in VPN it asks for username & password. So what is the user name? I have tried giving Computer-Name/User-Name. I have found my Computer Name by going to Control Panel/System/ & clicking 'Computer Name' tab & username from user accounts or it is shown when I login in windows account (Please correct me if the above procedure is wrong). But what is the password? I have tried giving the account password but it always give 'The username or password is incorrect.' My Question: How to find the username & password? For Information: a) I have Team Viewer 7 installed in one Windows XP PC & one Windows 8 PC. I like to create a secure connection between these two PCs. b) The two PCs are connected in the same local network via a router. Please ask if you need additional information.

    Read the article

  • Driver denied access to PCI card

    - by Corin
    Alright, I asked this on StackOverflow (here) and they suggested trying ServerFault to get help on permissions. So here's the deal. We designed a custom PCI card and wrote the driver for it. It's been working for years without problems but now we encountered one particular installation were it doesn't work. The problem is that we cannot connect to the PCI to begin communication with it. We tried replacing the card and had the same problem. We had the motherboard replaced thinking the PCI slots were bad. That didn't help either. We tried the cards in a different computer and they all worked. So it seemed to be something specific to the computer. The Windows Device Manager indicates the device is working properly and seems to have all the correct driver info. We now have this troublesome computer back at the office for testing. With the help of some extra debug info in the driver we determined that we cannot connect because access is denied. Sounds like a permissions issue to me. I should note that we are logged into the system as a local administrator. So what configuration option in Windows can prevent access to a device?

    Read the article

  • Work from home on an iPad?

    - by Alex Basson
    The situation: My wife has a 13" MacBook Pro that she uses for email, Facebook, web surfing, and working from home. I'm about to buy us our first iPad. My wife's brother's computer just went belly-up, and she's contemplating giving him her MacBook and just using the iPad. The question is whether or not this is possible or realistic. Obviously, the iPad is well-suited for the email/web/Facebook tasks, but the working-from-home thing is an absolute must -- if the iPad can't handle that, it's a deal-breaker. For my wife, working from home means two things: Accessing her workplace computer's Windows Vista desktop, which she currently does via Remote Desktop. Editing Office documents locally, which she currently syncs via Dropbox. Being able to edit documents locally is important, because sometimes she will download documents and edit them when she doesn't have network access (e.g. on the subway). I'm more than happy to get a keyboard dock for her, so typing won't be an issue. Are there any iPad apps she can use to access her work computer and edit her work files? Thanks for any suggestions!

    Read the article

  • Linux tools to choose suitable Cisco ASA 5500

    - by linuxcore
    I have a linux webhosting server which affects a high DDOS. I want to use Cisco ASA 5500 Series Adaptive Security Appliances to protect the linux server from this DDOS. I know there are many factors should you know before you choose the suitable hardware firewall like the amount of this DDOS and pps ..etc Please suggest a linux tools to measure those factors and to help me collect the required informations ( pps - amount of DDOS - concurrent connections and other factors ) Regards,

    Read the article

  • File locked / read-only

    - by oshirowanen
    On a networked computer, I have a file which is coming up as read-only because someone else has it open. This is not true. This is a file stored locally on the computer and it is not being used by anyone else. I can login to the same computer using a different user, and the file opens up fine. I just get the issue with a particular user account. Other than deleting theses account/profile and creating it again, how can I unlock this file? Double clicking on this file gives me a message saying The file is locked for editing by another user, or the file (or the folder in which it is located,) is marked as read-only, or you specified that you wanted to open this file read-only. I don't think the folder is locked, because I can use other files in that folder fine, it's just 1 particular file which is causing this issue. I know that only 1 user is using this file as the file is on his c: and the same file works fine if he logs off to allow another user to log in.

    Read the article

  • Why are my Windows 7 updates continuously failing?

    - by Chris C.
    I'm an advanced level user here with an odd issue. I have two Windows Updates that are failing to install, every single time. I'm getting a mysterious "Code 1" error on both updates, an error for which I'm having difficulty finding a solution. The updates in question are: Security Update for Microsoft Visual C++ 2008 Service Pack 1 Redistributable Package (KB2538243) System Update Readiness Tool for Windows 7 for x64-based Systems (KB947821) [May 2011] Because these updates are failing, the Shut Down button in my start menu always has the shield icon next to it, indicating that "new" updates will be installed on shut down. But, of course, they'll fail and when the PC is restarted, the shield icon is still there. When checking the update history and viewing the details of the failed updates, I get the following: Security Update for Microsoft Visual C++ 2008 Service Pack 1 Redistributable Package (KB2538243) Installation date: ?6/?29/?2011 3:00 AM Installation status: Failed Error details: Code 1 Update type: Important A security issue has been identified leading to MFC application vulnerability in DLL planting due to MFC not specifying the full path to system/localization DLLs. You can protect your computer by installing this update from Microsoft. After you install this item, you may have to restart your computer. More information: http://go.microsoft.com/fwlink/?LinkId=216803 and: System Update Readiness Tool for Windows 7 for x64-based Systems (KB947821) [May 2011] Installation date: ?6/?28/?2011 3:00 AM Installation status: Failed Error details: Code 1 Update type: Important This tool is being offered because an inconsistency was found in the Windows servicing store which may prevent the successful installation of future updates, service packs, and software. This tool checks your computer for such inconsistencies and tries to resolve issues if found. More information: http://support.microsoft.com/kb/947821 About My System I'm running Windows 7 Home Premium 64-bit. This is a custom PC build and the OS was installed fresh, not an upgrade from a previous version. I've been running this system for about four months. Windows Updates aside, the system is usually quite stable.

    Read the article

  • How I can recover files when the folder shows empty but the files are not deleted?

    - by Borror0
    Yesterday, my laptop caught a virus which caused massive damage. Since them, I have been trying to recover important files before reformatting my computer, a task the virus has not made easy. Restoration points predating the attack have been deleted. Most of my folders show empty. My Start menu is essentially empty, with the exception of Trillian and Mirror's Edge. The same goes for my Desktop, which only has programs which were installed after the attack. Searching for files though my computer is pretty much useless, as it only rarely brings up anything. I suspect most of my files have not been deleted. While my folders show empty, uTorrent still does display them and I can open them from here. Unfortunately, when I select Open Containing Folder, the folder still shows as completely empty even if I'm currently watching a video from that very folder. Further adding evidence to the not-deleted, just-missing theory, the data recovery software I'm using (Restoration) cannot find only find an handful of the missing files. If they were deleted, I could do a forensic recovery to get them back but since they're probably still somewhere on my computer, just out out of my reach, I can't find them. Under those circumstances, is there a way I can recover those files?

    Read the article

< Previous Page | 183 184 185 186 187 188 189 190 191 192 193 194  | Next Page >