Search Results

Search found 6834 results on 274 pages for 'dojo require'.

Page 195/274 | < Previous Page | 191 192 193 194 195 196 197 198 199 200 201 202  | Next Page >

• Packet flooding while configuring a Debian L2TP/IPSec client?

  - by Joseph B.

  I'm currently at my wits end trying to configure an L2TP over IPSec VPN connection on my Debian using openswan and xl2tp box connecting to a server of unknown configuration. I've managed to successfully establish the connection and everything appears to be working well until I attempt to set the VPN connection as my default route, at which point I see a massive flood of packets simultaneously being transmitted (on the tune of ~1.5 GB in about 2min) until the server drops my connection. Prior to this network traffic on all my interfaces is minimal. According to iftop the majority of this traffic appears to be coming out of port 12, although I can't seem to figure out how to finger a specific process. If I instead just route traffic destined for 74.0.0.0/8 through it I'm able to access Google's servers through the VPN without issue. My xl2tp.conf file is: [lac vpn-nl] lns = example.vpn.com name = myusername pppoptfile = /etc/ppp/options.l2tpd.client My options.l2tpd.client file is: ipcp-accept-local ipcp-accept-remote refuse-eap require-mschap-v2 noccp noauth idle 1800 mtu 1410 mru 1410 usepeerdns lock name myusername password mypassword connect-delay 5000 And my routing table looks like: Destination Gateway Genmask Flags Metric Ref Use Iface 10.5.2.1 * 255.255.255.255 UH 0 0 0 ppp0 10.0.50.0 * 255.255.255.0 U 0 0 0 eth0 10.50.0.0 * 255.255.0.0 U 0 0 0 eth0 10.0.0.0 * 255.255.0.0 U 0 0 0 eth0 192.168.0.0 * 255.255.0.0 U 0 0 0 eth0 loopback * 255.0.0.0 U 0 0 0 lo default * 0.0.0.0 U 0 0 0 ppp0 I'm seeing absolutely nothing in auth.log and syslog during this time and can't seem to find any other log files it might be writing to. Any suggestions would be appreciated!

  Read the article

• Large scale file replication with an option to "unsubscribe" from a replicated file on a given machine

  - by Alexander Gladysh

  I have a 100+ GB files per day incoming on one machine. (File size is arbitrary and can be adjusted as needed.) I have several other machines that do some work on these files. I need to reliably deliver each incoming file to the worker machines. A worker machine should be able to free its HDD from a file once it is done working with it. It is preferable that a file would be uploaded to the worker only once and then processed in place, and then deleted, without copying somewhere else — to minimize already high HDD load. (Worker itself requires quite a bit of bandwidth.) Please advise a solution that is not based on Java. None of existing replication solutions that I've seen can do the "free HDD from the file once processed" stuff — but maybe I'm missing something... A preferable solution should work with files (from the POV of our business logic code), not require the business logic to connect to some queue or other. (Internally the solution may use whatever technology it needs to — except Java.)

  Read the article

• Apache directory access with virtual host

  - by alexeygaidamaka

  I have a virtual host with a configuration like that. When i'm trying to get into foobar.com/dir providing valid username/password pair i get 403 forbidden page instead of that directory contents. www.foobar.com/dir has 777 rights, .httpaswd is chmoded 644. But i can't figure out why i am still not seeing contents. Please, give me a hint. ServerAdmin webmaster@localhost ServerName www.foobar.com ServerAlias www.foobar.com DocumentRoot /var/www/foobar <Directory /> Options FollowSymLinks AllowOverride All </Directory> <Directory /var/www/foobar> Options -Indexes FollowSymLinks AllowOverride All Order allow,deny allow from all </Directory> ScriptAlias /cgi-bin/ /usr/lib/cgi-bin/ <Directory "/usr/lib/cgi-bin"> AllowOverride None Options +ExecCGI -MultiViews +SymLinksIfOwnerMatch Order allow,deny Allow from all </Directory> <Directory /var/www/foobar/dir> AllowOverride AuthConfig AuthName "Authorize yourself, please!" AuthType Basic AuthUserFile /etc/apache2/.htpasswd AuthGroupFile /dev/null Allow from All Order Allow,Deny Require valid-user

  Read the article

• Latitude D600 USB port problem

  - by Moab

  Both USB ports stopped communicating on my D600, they have power, my optical mouse still lights up, no device works on the ports, everything is fine in Device manager in Dual boot XP and W7. Checked the bios, not much in there for USB. No usb device shows up when I use the F12 boot device menu either, so it must be some hardware issue. I have another hard drive with Ubuntu on it, popped it in and USB does not communicate with it either. Appears to have 5v but no communication, any Ideas besides another motherboard or USB card for the pcmcia slot (these don't work to well from my research)? I mostly use them for mass storage devices and pcmcia slots don't supply enough power for these devices. Thanks to all who answer with last ditch efforts. I hate to give up on it, its been good to me and still runs rather well for its vintage. EDIT: I did inspect the ports with a flashlight and did a partial disassembly of the laptop in an attempt to check the solder joints, but would require complete motherboard removal to see them, that is where I stopped. .

  Read the article

• How to (properly) back up a live QEMU/KVM VM?

  - by Roman

  I'm currently engineering a backup solution for KVM VM's as an additional measure to traditional backups. Unfortunately, all currently (August 2013) existing solutions I came across so far either: do not ensure a consistent backup of the VM (losing RAM state, creating a dirty image, or other things), or require lengthy downtime (complete VM shutdown while backing up). I'm aware of QEMU/libvirt's functionality of taking snapshots, however, it's not yet usable since: image-internal snapshots present you with an ever-changing image file, resulting in a likely dirty backup (assuming one uses qcow2 images at all). one cannot yet merge a currently active external snapshot into the original backing image ("blockcommit"). Out of the above reasons, I'm now implementing a script that: Saves the VM's state and halts it Sets up a devicemapper snapshot(s) where the VM's disk images and state reside Resumes the VM Mount the snapshot(s) of step 2. Backs up the VM's disk and state (configuration for convenience) Merges back the snapshot(s). If I got everything right, this will take consistent backups of VM's with only seconds (if at all, since 1-3 is fast, possibly sub-second) of downtime. Of course, when restoring, the VM will be way in the past, but at least giving me the option of an orderly shutdown/reboot. Am I missing something with this solution? Or has someone indeed already implemented this?

  Read the article

• Cisco IOS ACL: Don't permit incoming connections just because they are from port 80

  - by cjavapro

  I am going much based on my memory and I may not be correct on all of this. On a Cisco 851 (IOS) that uses a BVI or a bridge-route (the servers on the inside are configured with static and public IP addresses). I would apply two access lists (both end with deny ip any any log) on FastEthernet4 (the WAN port). There would be one for FA4 in and another for FA4 out. FA4 out would have a line like access-list 110 permit 98.76.54.0 0.0.0.255 gt 1023 any eq http I think this means from 98.76.54.* with a from port of at least 1024 can connect to any other machine with a destination port 80. So, then I have to allow the response to the HTTP connection. FA4 in would have a line like access-list 120 permit any eq http 98.76.54.0 0.0.0.255 gt 1023 Now the problem with that is that anybody on the outside can set their from port to port 80 and then connect to any inside port that is at least 1024. How do we prevent this and require the incoming data to be a response to the outgoing data.

  Read the article

• Outlook 2007 panes keep moving when changing resolution

  - by SilverbackNet

  This problem is really bugging one of our users ever since he got a larger monitor. Now that the monitor has a different resolution than his laptop, every time he unplugs it to go home, the three Outlook panes get all jumbled up. The navigation is huge, the list is shoved over, and the reading pane is almost smushed out of existence, the the opposite when he comes back in and the reading pane fills the screen. He's sick of adjusting it every day. He always runs it maximized, for maximum reading area. Keeping the application within a 1024x768 window wouldn't really be an option for him. Is there any way built into Outlook to automatically adjust pane sizes when the resolution changes? If not, is there a third-party app that can help, or a way to script the changes into the registry somehow? (I can do running the script whenever the screen state changes.) If this is fixed in 2010 I might be able to convince the other admin that this is a good enough reason to allow it (which will require a new beta version of our archiving software).

  Read the article

• linux shutdown hang with wifi cifs mounts

  - by Sirex

  Since fedora 15 (and now with 16) it seems that wireless clients take a long while to shutdown when they have network filesystems mounted at shutdown time. I've pushed out a cifs mount via puppet, and all clients have it, including those on wireless. If say a laptop is on a wired connection it shuts down just fine, but if its on the wifi at the time (and no wired connection) it'll hang at the fedora f logo. I'm not sure if its indefinite or just a really long while, but ill give it a test when i shut this machine down in a second. Needless to say its pretty annoying, so is there a way of causing the machine to shutdown even if network connectivity has been lost at unmount time, -- or an official way to reorder events so the wireless card is kept up until after the unmount happens during the shut down process (short of writing a custom script for shutdowns which is a bit of a kludge) ? It does this on multiple machines, and all started doing it when we went from fedora 14 to 15. It was such an obvious issue i'd kind of assumed someone must have reported it or there was an easy fix, but i've not discovered anything yet. Additional info: I can confirm that manually unmounting the mounts then shutting down (sudo shutdown or the xfce shutdown button) will shutdown just fine, it only hangs if the mounts are still mounted The puppet config that sets the mount looks like this (now with the _netdev entry that is indeed pushed to clients successfully, but makes no difference): file { "/mnt/share": ensure = directory,} mount { "/mnt/share": atboot = true, ensure = mounted, remounts = false, fstype = cifs, device = "//srv/share", options = "user,gid=shareusers,uid=${user},file_mode=0700,dir_mode=0700,credentials=/root/.smbcreds,_netdev", require = [ File["/mnt/share"], Group["shareusers"] ], } }

  Read the article

• Ngins wont send POST to fastcgi backend, but GET works fine?

  - by xyld

  Not sure why, but it is happy sending a GET to the fastcgi backend (Mercurial hgwebdir in this case), but simply resorts to the filesystem if the request is a POST. Relevant parts of nginx.conf: location / { root /var/www/htdocs/; index index.html; autoindex on; } location /hg { fastcgi_pass unix:/var/run/hg-fastcgi.socket; include fastcgi_params; if ($request_uri ~ ^/hg([^?#]*)) { set $rewritten_uri $1; } limit_except GET { allow all; deny all; auth_basic "hg secured repos"; auth_basic_user_file /var/trac.htpasswd; } fastcgi_param SCRIPT_NAME "/hg"; fastcgi_param PATH_INFO $rewritten_uri; # for authentication fastcgi_param AUTH_USER $remote_user; fastcgi_param REMOTE_USER $remote_user; #fastcgi_pass_header Authorization; #fastcgi_intercept_errors on; } GET's work fine, but POST delivers this error to the error_log: 2010/05/17 14:12:27 [error] 18736#0: *1601 open() "/usr/html/hg/test" failed (2: No such file or directory), client: XX.XX.XX.XX, server: domain.com, request: "POST /hg/test HTTP/1.1", host: "domain.com" What could possibly be the issue? I'm trying to allow read-only access via GET's to the page, but require authorization when using hg push to the same url which sends a POST request.

  Read the article

• Nokia E75 Mail for Exchange

  - by Sebastian

  Hi, I have a SBS2003 runing Exchange Server 2003 SP2. My OWA has a godaddy certificate valid for 3 years to come installed. HTTPS works fine for OWA. The certificate has also been copied into the Nokia E95 I am trying to syncronize my Nokia E75 via Mail for Exchange to my mail account on the Exchange server. These are the steps i use: Menu Email New Start Select Internet Gateway Than i enter the details: [email protected] I select company email Mail for Exchange In the domain menu i enter : mydomain In the username/password menu i enter : myusername/mypassword In the server menu i enter : mail.mydomain.com (where the DNS resolves into the server's IP address) In the secure access i select : Internet / Secure / 443 NOTE : port 443 has been opened on my SBOX and forwarded to the exchange server. On IIS default website properties directory security secure communications edit the "Require Secure Channel SSL" is enabled. However, when i try to sync my phone i get the following error code: * Mail for Exch permissions illegal. Check permission configuration. * The phone log gives the following information : Username or Password Illegal. Correct Username and/or Password in the profile options. I've tried speaking with the Phone service support but they cannot identify the problem. Any help will be much apreciated.

  Read the article

• Creating a private wiki

  - by Hand-E-Food

  I want to create a simple, private wiki, but am really struggling to find what I need. I require the following features: Private wiki. Only I will read or write it. Some formatting capability: headings, bold, italic, bullets, block quotes Wiki Viewer for Windows 7. If it comes with an editor, I need to be able to hide it. Page Editor for Windows 7. Page Editor for iPhone. Synchronize by cloud but available offline in Windows. So far, my research has led me to Markdown language. I can easily edit this as plain text using Notepad++ for Windows and Elements for iPhone. I can sync these files through Dropbox and have them available offline. What I can't find is a suitable viewer for Windows. I'd prefer to steer away from using HTML due to its verbose formatting codes. Can anyone recommend a solution for me? If need be, I'll happy to make a small one-off payment for software.

  Read the article

• Intel HD Graphics vs NVIDIA Quadro FX 380 PCI-E

  - by Michael

  I recently purchased an Acer Veriton which has an i5-650 processor, Windows 7 Pro (64 bit) and Intel HD Graphics listed as the video card. I also purchased a PNY nVIDIA Quadro FX 380 PCI-E card for improved picture and home video viewing and editing. I have already replaced the original 300 wattt power supply to a 430 watt Antec Truepower I had on hand and boosted the RAM to 8 gigs from the original 4. Question 1) Am I getting any improvement in visual quality or system speed with the Quadro or is it a waste of money and I should just save up to buy a bigger video card? This card was on sale for $115. If I am getting improvement then I need to ask another question. Question 2) Instructions for the Quadro installation are as follows... 1--Uninstall the existing VGA driver. -Remove the existing Display Driver via "Add or Remove Porgrams". -Shut down your computer. 2--Remove your Existing Graphics Board (or Disable Integrated 3D Graphics Controller). skipping instructions on how to remove existing graphics board -Systems with integrated (also know as on-board) 3D graphics may require you to disable the integrated 3D graphics system. Consult the owners or vendor manual that came with your PC on how to properly do this. So is the Intel HD Graphics considered a 3D graphics controller? If so should I just contact Acer or can anyone give me instructions? Thanks in advance for any help.

  Read the article

• linux: per-process monitor, every 10 minutes, with history access

  - by Inbar Rose

  I really didn't know a better way to ask my question, hence you get a horribly named question. I will explain what i want to do, maybe that will help you help me. I would like to have my linux machine continuously monitor (every 10 minutes) all the processes on my machine. The information from each process that I require is the name, CPU usage, allocated (virtual) memory, and resident (ram) memory. If these periodic reports were to be looked at, they would look something like this: PROCESS CPU RAM VIRTUAL name1 % MB MB name2 % MB MB ...etc..etc These reports should be stored in such a way that I can access them at a later date by giving a date/time scope (range). For instance, if I want to see the history of my processes from 12:00:00 1.12.12 till 12:00:00 2.12.12 I can - and it should give me the history of the processes for every 10 minutes between those date/time borders. The format of the return is not important, that will be handled by a script anyway and can be modified into anything I need. I have looked into a few things so far, but have not found something that clearly meets my needs. Among the things i searched: sar, free(1), top(1).. and a few other things. It should be a simple issue, i can already see all this information by simply looking at my htop, but i need only a tool that will gather the desired fields for me for each processes every 10 minutes, and then also let me extract slices of that data based on date/time scopes (ranges). note: I have limited experience with linux, so please give detailed information. note2: The desired output will be something like this (after receiving the desired range) CPU USAGE BY PROCESS: proc_nameA 1,2,2,2,2,2...... numbers represent % usage every 10 minutes... proc_nameB 4,3,3,6,1,2...... The same idea with the other information.

  Read the article

• Remotely port forward/launch process or a client-less remote desktop app?

  - by DC177E

  I have an XP box running Logmein at a remote location behind a linksys router, which was running well for a whole of four days, until we had a power failure. Our ISP gave us a new IP, the machine restarted, and logmein did not autorun (or, at least, it did not automatically sign in), and our service (which may or may not be a Minecraft server with non-backed-up save files) also did not run upon startup. Logmein does not register the new IP (it still displays the old one). I have a DDNS updater service, so I do know the new dynamic address. I have tried using the built in XP remote desktop service, but, as with almost all non-cloud-based remote desktop services, it requires a port forward. Thus, I would appreciate it if anyone has any ideas as to: A: Any way of accessing our router remotely to forward the remote desktop port. I've seen the Remote Management option (forwarding the setup page to port 8080), but I do not have it enabled. I've tried UPnP, but again, the setup page for our router is not forwarded. B: Any way of remotely launching a process that does not require port forwarding (or uses ports 255XX, 18XXX, or 9000.), such as a remote console service built into XP. I realize this is a near impossibility. C: A Way to remotely start logmein, and sign in, which is likely a definite impossibility. Sorry if this is too specific for Stackexchange, or if I've put it into the wrong section (is SuperUser the correct place for this?). Ideas would, again be much appreciated, as shot-in-the-dark-like this may be.

  Read the article

• How large is the performance loss for a 64-bit VirtualBox guest running on a 32-bit host?

  - by IllvilJa

  I have a 64-bit Virtualbox guest running Gentoo Linux (amd64) and it is currently hosted on a 32-bit Gentoo laptop. I've noticed that the performance of the VM is very slow compared to the performance of the 32-bit host itself. Also when I compare with another 32-bit Linux VM running on the same host, performance is significantly less on the 64-bit VM. I know that running a 64-bit VM on a 32-bit host does incur some performance penalties for the VM, but does anyone have any deeper knowledge of how large a penalty one might expect in this scenario, roughly speaking? Is a 10% slowdown something to expect, or should it be a slowdown in the 90% range (running at 1/10 the normal speed)? Or to phrase it in another way: would it be reasonable to expect that the performance improvement for the 64-bit VM increases so much that it is worth reinstalling the host machine to run 64-bit Gentoo instead? I'm currently seriously considering that upgrade, but am curious about other peoples experience of the current scenario. I am aware that the host OS will require more RAM when running in 64-bit, but that's OK for me. Also, I do know that one usually don't run a 64-bit VM on a 32-bit server (I'm surprised I even got the VM started in the first place) but things turned out that way when I tried to future proof the VM I was setting up and decided to make it 64-bit anyway.

  Read the article

• All computers on network get stuck waiting for some sites indefinetely

  - by zacaj

  This happens across three computers, running windows 7 and Ubuntu, firefox, opera, and chrome (all latest versions). I am connected to the internet through a Verizon wireless usb modem. When I try to open some web pages they will never finish loading (and usually never even show anything). The status bar at the bottom of the browser will display "Waiting for X" The servers it gets stuck on include: platform.twitter.com s7.addthis.com connect.facebook.net ajax.googleapis.com 2mdn.net Ive been getting away with just blocking them in AdBlock up until now, however the last two have been causing problems. There are some sites which require googleapis.com to load correctly, and some that wont ever load unless its blocked. eBay requires access to 2mdn.net to load pictures. On top of this its getting really annoying having to update AdBlock across all these computers whenever a new site pops up. I'm hoping there's some easier way to fix this? The different sites causing the freeze indicate to me that it's either a problem on my end (somehow?) or some server side software that got updated with a new bug?

  Read the article

• Remote offscreen rendering

  - by redmoskito

  My research lab recently added a server that has a beefy NVIDIA graphics card, which we would like to use to do scientific computations. Since it isn't a workstation, we'll have to run our jobs remotely, over an ssh connection. Most of our applications require doing opengl rendering to an offscreen buffer, then doing image analysis on the result in CUDA. My initial investigation suggests that X11 forwarding is a bad idea, because opengl rendering will occur on the client machine (or rather the X11 server--what a confusing naming convention!) and will suffer network bottlenecks when sending our massive textures. We will never need to display the output, so it seems like X11 forwarding shouldn't be necessary, but Opengl needs the $DISPLAY to be set to something valid or our applications won't run. I'm sure render farms exist that do this, but how is it accomplished? I think this is probably a simple X11 configuration issue, but I'm too unfamiliar with it to know where to start. We're running Ubuntu server 10.04, with no gdm, gnome, etc installed. However, xserver-xorg package is installed.

  Read the article

• How do i play nicely with MS SQL/SQL Server 2008

  - by acidzombie24

  Big problem. I have nearly given up. I am trying to port my prototype to use MS SQL so it will work on a server once i get it (the server will be SQL Server 2008, shared, i dont know any more info). So i tried to connect to SQL Server via visual studios IDE and had no luck. I enabled TCP and named pipes and restarted the service (and computer) with still no luck. I remembered about mdf files so i made that after an obstacle of not being able to make the connect string require i figure out visual studio has it in its properties and successfully connected with that. Then i had a problem with nested transactions. After not being able to figure out how to check i wondered if i can configure it to allow it somehow. I always thought all of MS were the same except for limitations but sql server seems to support nested transactions so theres no point trying to work around the problem with .mdf files since i wont need them and really just used it to port the base of my sql code and to check if syntax is correct. I tried installing SQL Server Management Studio since people mentioned it several times (as a solution or at least help). When installing it on windows 7 it says it may not be compatible. After running it, it launched SQL Server Installation Center (64-bit) which doesnt seem to be the same thing as i dont see a way to modify any of my server (networking) configurations or edit user permissions, etc. I am clueless what to do next. Does anyone have any ideas? I'm posting here bc i think my problem is more configurations and sql server then programming.

  Read the article

• Allowing Sharepoint to relay email through Exchange

  - by dunxd

  I have written a Sharepoint 2007 web part that sends a field from a form to a specified email address. I have got the form working as I require, but at present it can only send to internal email addresses. Sharepoint's email functions use SMTP to send to our Exchange 2003 server, but because our Exchange server is configured to prevent relaying, if the To: address is not at a local domain, it won't deliver the mail. I don't want to open up our Exchange server to be a completely open relay. What I want is to allow my Sharepoint servers to send mail to addresses outside our domain. The following seem possible: Allow all mail sent from one of the Sharepoint servers to be relayed Allow all mail from a web application pool account to be relayed (I am not sure that the application pool authenticates to the SMTP server though) A combination of the two Can anyone advise on the best way of doing this? Is setting up a dedicated SMTP server on the Exchange server (not a separate physical server) the right way of going about this? EDIT: Note this is for Exchange 2003. There is a post on setting this up in Exchange 2007 which appears to have recognised the frequent requirement to do what I need. It doesn't give much detail on 2003 though. Can anyone expand?

  Read the article

• How does one debug Windows network share authentication?

  - by ajs410

  I have machine0 with 32-bit Vista, logged in as a domain user, running a VMWare image of 32-bit Vista, logged in as a local user, with the VM set to bridge the network. From an administrator account (called admin) within the VM, I try to access the hidden C$ share on machine0 (i.e. start - run - "\\machine0\C$\"). I get no prompts for credentials. Worse, machine0 has an admin account (different password), and machine0\admin gets locked out when VM\admin tries to access the network share. I get a message several seconds later, which feels like a cached credential failure leading to the lockout. I have checked several places for cached credentials; net use, Stored Usernames and Passwords, mapped shares. I rebooted (both machine0 and VM) to make sure the session was clear of any cached credentials. I can force net use to use my domain credentials when accessing machine0, and then I can see the share. I can also see shares that do not require credentials. I decided to try another machine on the network (machine1), 64-bit Vista, local user. This machine has no lockout policy, and after several seconds (feels like failed cached credentials again) it prompts me for credentials. After I enter them, it re-prompts me, saying "logon unsuccessful" (tried my domain credentials, and also machine1\admin's). Which is bogus, because I proceed to log on with remote desktop using the machine1\admin credentials. I have tried this on another machine (machine2, 64-bit Vista), running a copy of the same 32-bit VM, and I don't remember having this problem. machine0 has a fingerprint reader...could that try storing passwords and interfere? Are there any places I'm missing where there could be cached credentials? Is there a way to see what credentials are flying around when I try to connect?

  Read the article

• Loading the preview function of AUCTeX 11.86 on macports Emacs-app 23.2.1 port.

  - by Sarah

  I've installed Emacs-app 23.2.1 via MacPorts and I'm trying to install AUCTeX 11.86 so that it will work on this installation. I've run the following configure line for AUCTeX and that seems to work. ./configure --with-emacs=/Applications/MacPorts/Emacs.app/Contents/MacOS/Emacs --with-lispdir=/Applications/MacPorts/Emacs.app/Contents/Resources/site-lisp/ --with-texmf-dir=/usr/local/texlive/2010basic/texmf-local/ make and make install seem to work, and I've added the following line to my init.el (require 'tex-site) as per the installation instructions. However, when I open a TeX file, the Preview menu does not show up (although the LaTeX menu does.) The following are some of my tests: M-x load-library RET preview-latex RET doesn't seem to do anything. M-x load-library RET preview RET brings up the Preview menu. Is it safe to somehow add the load-library preview to my init.el? Or do I risk mucking up something? I'm new to Emacs and primarily trying to learn it because of the AUCTeX preview features, but I don't feel very safe in this environment yet.

  Read the article

• optimal folder structure for storing 100k files on a USB drive

  - by cherouvim

  I need to store 100k files (around 40GB) in a USB drive. Each file has a unique int id (e.g 45000). Option one is to put all files in a single folder: root/ root/1.pdf root/2.pdf root/3.pdf ... root/567.pdf root/568.pdf root/569.pdf ... root/10001.pdf root/10002.pdf root/10003.pdf ... root/99998.pdf root/99999.pdf root/100000.pdf Option two is to create a [1-9][0-9]* folder hierarchy based on that id: root/ root/1/file.pdf root/2/file.pdf root/3/file.pdf ... root/5/6/7/file.pdf root/5/6/8/file.pdf root/5/6/9/file.pdf ... root/1/0/0/0/1/file.pdf root/1/0/0/0/2/file.pdf root/1/0/0/0/3/file.pdf ... root/9/9/9/9/8/file.pdf root/9/9/9/9/9/file.pdf root/1/0/0/0/0/0/file.pdf Which option will scale better? I can understand that the second option will require tons of folders but each folder will at most contain 10 folders and 1 file. Maintenance will not be an issue since everything will be controlled by an application. Note that this is a USB drive on linux and based on the above I'd also like to know whether I should go with FAT32 or NTFS.

  Read the article

• Optimize Apache performance

  - by Phliplip

  I'm looking for ways to optimize our current web server hosted in-house. I'm trying to supply as much relevant information below. Please let me know if you would require additional information in order to assist. Server is running 1 single website, which is an online pizza ordering platform built on Zend Framework (ver1). On traffic stats from the last month aprox 6.000 pageloads per day, concentrated mainly around dinnertime. Around 1500 loads/hour peaks in that period. We recently upgraded from a 2/2mbit aDSL-line to 100/100mbit fiber, and we still have performance issues at dinner time. We assumed the 2mbit was the issue. Website is pretty snappy in low-load periods. Hardware CPU: Intel(R) Xeon(R) CPU 5160 @ 3.00GHz (3000.13-MHz K8-class CPU) Mem: 328M Active, 4427M Inact, 891M Wired, 244M Cache, 623M Buf, 33M Free Swap: 16G Total, 468K Used, 16G Free (6GB physical, 16GB swap) Filesystem Type Size Used Avail Capacity Mounted on /dev/ad7s1a ufs 4.8G 768M 3.7G 17% / devfs devfs 1.0K 1.0K 0B 100% /dev /dev/ad7s1g ufs 176G 5.2G 157G 3% /home /dev/ad7s1e ufs 4.8G 2.8M 4.5G 0% /tmp /dev/ad7s1f ufs 19G 3.5G 14G 19% /usr /dev/ad7s1d ufs 4.8G 550M 3.9G 12% /var Server OS FreeBSD 8.2-RELEASE Software apache-2.2.17 php5-5.3.8 mysql-server-5.5 Apache footprint (example, taken from # top) 31140 www 1 45 0 377M 41588K lockf 2 0:00 0.00% httpd 31122 www 1 44 0 375M 35416K lockf 2 0:00 0.00% httpd 31109 www 1 44 0 375M 38188K lockf 2 0:00 0.00% httpd 31113 www 1 44 0 375M 35188K lockf 2 0:00 0.00% httpd Apache is using the prefork MPM, APC (Alternative PHP Cache). SSL module is loaded, but not utilized (as in don't really work, thus not used). There is a file containing settings for MPM modules, but as i see it's not included in the httpd.conf file, the include line is commented out. Thus i would guess that the prefork MPM is working of default values too. Here are some other Apache conf values that i found - which are included in https.conf Timeout 300 KeepAlive On MaxKeepAliveRequests 100 KeepAliveTimeout 5 UseCanonicalName Off HostnameLookups Off

  Read the article

• Is there such a thing as a file hosted container which deduplicates data held within?

  - by Mallow

  Background I have backups of a website which stores all of it's data into a single file. This file is several gigs large and I have many different backups of this file. Most of the data within is mostly the same plus whatever was added or changed to it. I want to keep all the concurrent backups I've made through the years in case I find a horrible surprise of data corruption along the line. However storing a 10gig file every month gets expensive. Seeking Solution I've often thought about different ways of alleviating this problem. One thought that comes up very often combines the idea of a duplicating file system which doesn't require it's own partitioned volume on a hard drive. Something like what truecrypt does, what it calls, "file hosted containers" which when using the truecrypt program allows you to mount and dismount that volume as a regular hard drive. Question Is there a virtual hard drive mounter which uses file-based container which uses data deduplicaiton file system? (This question is a little awkward to put into words, if you have a better idea on how to ask this question please feel free to help out.)

  Read the article

• How to deploy new instances of the same application (on 1 server) automatically?

  - by Intru

  I'm working on a SaaS application where each customer runs its own version of the application. All the application instances currently run on a single server. This works quite well for us (we need less resources in total). The application doesn't use a lot of resources, so even a small VPS would be overkill (and more expensive). Adding a new customer is currently quite a bit of work: Create a user that is allowed to ssh Create a new MySQL database and user Create a virtual host for the application Log in with the new user, do a git checkout of the application (in the right location) Create tables in the new database, and add some init data Add some cron jobs Create a first user that can log in Add this new instance to capistrano What would be the best way to automate these tasks? Are the applications that can (given proper configuration) do this? Ideally this should be usable for a sales-person (so something web-based). I could write a (bash) script that does most of these tasks, and then maybe add a small web-based wrapper where someone could provider the domain/default user information. Of course, this would also require a delete-script, since some customers will eventually leave, which means that you need a list of all existing customers/instances.

  Read the article

< Previous Page | 191 192 193 194 195 196 197 198 199 200 201 202  | Next Page >