Search Results

Search found 19557 results on 783 pages for 'networking programming'.

Page 198/783 | < Previous Page | 194 195 196 197 198 199 200 201 202 203 204 205  | Next Page >

• "Piping" to MPD

  - by oxinabox.ucc.asn.au

  I would like to "Pipe" the output of my local sound card to MPD on a networked music server. Anyone have any suggestions how to go about this? I'm thinking maybe i can make a live MP3 stream? maybe over the web, or over the intranet? (IIRC MPD supported MP3 streams, i've had Internet radio steams going (though I didn't set them up) I'm not very experienced with MPD, or with webcasts

  Read the article

• On VMWare Server, how can I specify which Ethernet port should be the one to be bridged?

  - by DrDavid

  My server has 4 ethernet ports; 1 uses a APIPA address to connect to a DroboElite (that's how they're designed to work), 1 is connected to the LAN, and the other two are unused currently. The issue is that VMWare Server seems to have an affinity to the port that's connected to the Drobo, which means that it can never reach the internet. If I disable the Drobo port, everything works just fine. If I enable the drobo port, nothing works (well, the drobo works, but the virtual machine doesn't ;) ) How can I tell VMWare Server to NOT use the drobo port when I'm bridging the connection?

  Read the article

• How does IPv4 Subnetting Work?

  - by Kyle Brandt

  This is a Canonical Question about IPv4 Subnets How does Subnetting Work, and How do you do it by hand or in your head? Can someone explain both conceptually and with several examples? Server Fault gets lots of subnetting homework questions, so we could use an answer to point them to on Server Fault itself. What is classless routing and why is class-based routing obsolete? If I have a network, how do I figure out how to split it up? If I am given a netmask, how do I know what the network Range is for it? Sometimes there is a slash followed by a number, what is that number? Sometimes there is a subnet mask, but also a wildcard mask, they seem like the same thing but they are different? Someone mentioned something about knowing binary for this? What is NAT (Network Address Translation).

  Read the article

• Cisco Switching Module and HSRP interface Tracking

  - by Kyle Brandt

  When using 4 port switching module where each port is configured to switchport access vlan ##, for HRSP should I track the vlan interface or the FastEthernet interface? interface FastEthernet0/0/0 switchport access vlan 10 interface Vlan10 ip address 12.12.12.1 255.255.255.0 int FastEthernet0/1 ip address 192.168.1.2 255.255.255.0 standyby ip 192.168.128.1 standby track ?? ! FastEthernet 0/0/0 or Vlan 10?

  Read the article

• ProCurve ACL to prevent a subnet from leaving the switch

  - by kce

  I have a single HP ProCurve 2610 in a remote location that is connected in with the rest of the network via SHDSL. There are two Layer-3 networks on this segment. ACLs are setup to deny one subnet (192.0.2.0/24) from ever being able to leave the switch by virtue of being applied to port attached to the upstream connection. The other subnet should be permitted to freely leave the switch. Both subnets are on the same VLAN. Unfortunately SFlow very clearly show broadcast traffic from 192.0.2.0/24 on the upstream connection. ProCurve ACLs are not my strong suit but I feel like I'm missing something very simple here. ip access-list extended "Filter for Camera Network" deny ip 192.0.2.0 0.0.0.255 0.0.0.0 255.255.255.255 log permit ip 0.0.0.0 255.255.255.255 0.0.0.0 255.255.255.255 exit interface 24 name "DSL - UPLINK" access-group "Filter for Camera Network" in exit Unless I am mistaken traffic from 192.0.2.0/24 should be dropped as it crosses the uplink port (int 24) whereas all other traffic will be permited by the following default allow rule. What exactly am I missing here? EDIT: Firstly, why do you have two subnets contained in the same VLAN? Because that's how it was configured by a previous administrator and while it makes conceptual sense that a single subnet is "mapped" to a single VLAN there's no technical constraint that I am aware of that makes this have to be the case. Instead of filtering inbound traffic on your uplink, you should be filtering outbound traffic. The HP2600 series can only filter inbound traffic on interfaces. Should I change my filter to deny any to 192.0.2.0/24?

  Read the article

• Encrypted WiFi with no password?

  - by Ian Boyd

  Is there any standard that allows a WiFi connection to be encrypted, but not require a password? i know that (old, weak) WEP, and newer WPA/WPA2 require a password (i.e. shared secret). Meanwhile my own wireless connections are "open", and therefore unencrypted. There is no technical reason why i can't have an encrypted link that doesn't require the user to enter any password. Such technology exists today (see public key encryption and HTTPS). But does such a standard exist for WiFi? Note: i only want to protect communications, not limit internet access. i get the sense that no such standard exists (since i'm pretty capable with Google), but i'd like it confirmed. Claraification: i want to protect communcations, not limit internet access. That means users are not required to have a password (or its moral equivalent). This means users are not required: to know a password to know a passphrase to enter a CAPTCHA to draw a secret to have a key fob to know a PIN to use a pre-shared key have a pre-shared file to possess a certificate In other words: it has the same accessibility as before, but is now encrypted.

  Read the article

• I want to add a Quality Assurance domain. How do I handle DNS servers?

  - by Tim

  I'm advising a large client on how to isolate their dev and testing from their production. They already have one domain, lets say xyz.net with the active directory domain as "XYZ01". I want to add second domain say QAxyz.net and make its active directory domain "QA01" All development and QA servers would be moved to the QAxyz.net domain, the machines would be part of the QA01 domain. Note: Some of these servers will have the same name as the production servers for testing purposes. I believe we would have separate DNS servers for each domain. If I am logged into the QA01 domain, to access the production domain I would qualify my access like so: \PRODSERVER.xyz.net login: XYZ01\username Do I need to add a forwarder to my QAxyz.net DNS server so that it can see xyz.net? Would I need to do the same to the xyz.net DNS server to see QAxyz.net? I don't know how to advise them in this. Does anyone have any other recommendations to isolationg a QA domain? Many Thanks in advance! Tim

  Read the article

• How to configure 2nd network card for use in VMWare Workstation?

  - by Timo

  Hi all, I am using VMWare Workstation 6.5, connected to my network with a bridged adapter so that the virtual machine OS (Windows XP) has its own IP adress. This just worked out of the box. Now my host machine (Windows Vista) has an additional network card that is directly connected to another computer using a crossover cable (and fixed IP adress 10.1.1.4, while the "main" network connection is using DHCP with IP in the 192.68.0.* range). How can I use that network connection as well in the virtual machine? Do I need to bridge my 2nd network adapter to some VMnetX adapter? Do I need to add a host virtual adapter? I do not know much about networks, and the VMWare network settings really confuse me :-) Thanks, Timo

  Read the article

• dig lookup different from system lookup

  - by simao

  Hello, I am running dd-wrt and I configured it's dns server to resolve a few hosts inside my network. When I use dig to lookup these hosts, they are resolved OK, but when I try to ping those hosts I always receive an unknown host error message. For example: obe:~ simao$ dig dd-wrt ; <<>> DiG 9.6.0-APPLE-P2 <<>> dd-wrt ;; global options: +cmd ;; Got answer: ;; ->>HEADER<<- opcode: QUERY, status: NOERROR, id: 44026 ;; flags: qr aa rd ra; QUERY: 1, ANSWER: 1, AUTHORITY: 0, ADDITIONAL: 0 ;; QUESTION SECTION: ;dd-wrt. IN A ;; ANSWER SECTION: dd-wrt. 0 IN A 192.168.1.1 But then: obe:~ simao$ ping dd-wrt ping: cannot resolve dd-wrt: Unknown host Any ideas? Thanks.

  Read the article

• Virus blocking incoming connections ?

  - by Benoît

  Hello, on my windows 2003 server, all incoming connections are dropped. I can see them getting in using Wireshark, but even a single ping from another computer fails. All locally initiated connection work fine (i'm asking from the server). This server is the DC/DHCP/DNS/File server, so computer clients are in the dark. I've run varius antivirus and removal tools without any luck. The Windows Firewall is disabled. I'm wild-guessing at some virus/worm. How can i check why these incoming ICMP/TCP SYN/etc are dropped ? Anyone has any knowledge about such situations ? Thanks.

  Read the article

• Time-Machine backup over SSH tunnel to NFS mount

  - by BTZ

  I've recently started using a new NAS which runs CentOS 6.2. One of the purposes of the NAS would be to serve as a backup target. Whilst I have been using Apple's Time-Machine for a while and I am very satisfied with it, I'd like to continue using it. Backing up directly to an address in my network is no hassle; all works fine. For security reasons I'd like all my traffic to go through an ssh tunnel to the NAS. This way I can avoid needing to get a VPNserver (for personal reasons). As of NFSv4 the NFS deamon is bound to port 2049, which makes it easy for me to direct all traffic through a ssh tunnel. Tunnel: ssh -f admin@ms -L 2000:localhost:2049 -N Mount: mount -t nfs -o nfsvers=4,rw,proto=tcp,sync,intr,hard,timeo=600,retrans=10,wsize=32768,rsize=32768,port=2000 localhost:/mac_backup /Volumes/backup This works fine for Finder/terminal and throughput is almost equal to direct traffic. (CPU of the NAS does ride high when I reach max bandwidth though) Now the problem: With Time-Machine I can't use the NFS mount point mounted on localhost. TM seems to try to connect to it and then give me a "OSStatus error 65". I also tried using NFSv3 (I correctly forwarded all ports) with no luck. Can anyone shed a light on this and/or give a solution?

  Read the article

• Translating debian network configuration to gentoo

  - by thpetrus

  I just got rid off Debian on my VPS (OpenVZ) and installed Gentoo on it, however it is a plain Gentoo image without further configuration, i.e. no working network. I'm not familiar with Debian and coulnd't figure out how to get the network set up, these are the debian network files /etc/network/interfaces: auto venet0 iface venet0 inet manual up ifconfig venet0 up up ifconfig venet0 127.0.0.2 up route add default dev venet0 down route del default dev venet0 down ifconfig venet0 down iface venet0 inet6 manual up ifconfig venet0 add ipv6addr/128 down ifconfig venet0 del ipv6addr/128 up route -A inet6 add default dev venet0 down route -A inet6 del default dev venet0 auto venet0:0 iface venet0:0 inet static address external_ip netmask 255.255.255.255 auto venet0:1 iface venet0:1 inet static address internal_ip netmask 255.255.255.255 Please note that external_ip, internal_ip and ipv6addr are placeholders. I copied the /etc/resolv.conf, know the gateway_ip and also have another ouput of ifconfig, if necessary. This is what I came up with, /etc/conf.d/net: config_venet0="127.0.0.2 netmask 255.255.255.255 brd 0.0.0.0" config_venet0:0="external_ip netmask 255.255.255.255 brd 0.0.0.0" route_venet0:0="default via gateway_ip" config_venet0:1="internal_ip netmask 255.255.255.255 brd 0.0.0.0" Broadcast IP is taken from ifconfig debian output - however it doesn't work. A symbolic link net.venet0:0 -> net.lo in /etc/init.d/ was created and I added net.venet0:0 to the boot runlevel.

  Read the article

• Managing two internet connections in Windows XP, with different applications using different connections

  - by user932867535

  I have two internet connections, one has limited data but is fast, the other has unlimited data but is slow. What am trying to do is assign the unlimited data connection to the application which is downloading a large file, while surfing the net (using Firefox) with the other, faster connection. I tried connecting both connections, but every time I do that, all the applications just jump from the slower connection to the faster one. Is there any way in which I could achieve what I am looking for?

  Read the article

• How to increase signal/range of your Wi-Fi antenna-less repeater/booster over the network?

  - by kenorb

  I've BT Home Hub in the upper flat (2-3 walls behind) and I'm using WPS Wireless-N Wifi Range Router Repeater Extender in my flat where I'm using my laptop. These are antenna-less devices. Are there any life-hack tricks to increase signal/range of my repeater without buying the new more powerful repeater? I've tried already to move my repeater closer to the ceiling or putting the aluminium foil underneath, but it didn't help. Are there any methods, specific plates or materials which can boost the signal? Specification: Model: WN518W2 Frequency range: 2.4-2.4835GHz Wireless transmit power: 14 ~17 dBm (Typical) Wireless Signal Rates With Automatic Fallback: 11n: Up to 300Mbps(dynamic), 11g: Up to 54Mbps(dynamic), 11b: Up to 11Mbps(dynamic) Modulation Technology: DBPSK, DQPSK, CCK, OFDM, 16-QAM, 64-QAM Receiver Sensitivity: 300M: -68dBm@10% PER / 150M: -68dBm@10% PER / 108M: -68dBm@10% PER / 54M: -68dBm@10% PER / 11M: -85dBm@8% PER / 6M: -88dBm@10% PER / 1M: -90dBm@8% PER Product dimensions: 11 * 6 * 7cm

  Read the article

• 4 - 7 second delay accessing Mysql across the network

  - by Kristiaan

  Hello, our company has recently purchased a new server with the intention of replacing our aging database server. its a full 64bit 2008 enterprise system, i have got the basic server setup and configured and then installed the 64bit version of mysql on the server, this has then been configured to match where possible our existing server as much as it can. however i have noticed that when it was swapped with the production database server our software systems had an increased delay accessing the mysql database this was anything beween 4 - 7 seconds. i have tried disabling TOE, IPv6 and a few other suggested soultions to this but so far cannot find out where this slowdown is coming from. replacing the server with the production one and the delay goes away. in terms of software and hardware the servers are not very identical at all due to one being windows 2003 std with a 32bit server and the new one being windows 2008 enterprise with a 64bit server. thanks Kris

  Read the article

• Does anyone know about nagios plugin that uses nmap and does port checking??

  - by Eedoh

  Hi to all. I need to monitor open and closed ports on dozens of hosts. I've found a Nagios plugin that does what I need, but I would have to use this script through nrpe. Some of the hosts are powered by linux and they all have perl installed. But some of them are Windows machines, and it's not convenient for me to install perl on every one of them. That's why I can not use this plugin. I hope that there's Nagios plugin that uses nmap, or something similar, so it could check ports on every host remotely, without installing plugins on remote hosts, only on server.

  Read the article

• Determining the required depth and specifications for a server cabinet

  - by Bingu Bingme

  I'm trying to understand the considerations ("why") that go into determining the specifications ("what") for a rackmount server cabinet, in order to determine what sort of rack I should purchase for my home use. Since this is for home use, I won't be following certain best practices (eg. hot/cold aisle, not even air conditioning) and may be willing to sacrifice in various areas in order to reduce cost and footprint - but please advise if there are safety concerns or other considerations to note. The most basic specs for a server cabinet are the dimensions (external width x external depth x usable height). Width: commonly 600mm or 800mm (if the use case requires extra clearance around the sides, such as if there is lots of cabling). In my case and most common cases, I'm going to stick with 600mm. Height: Select a sufficiently tall rack to fit my equipment. But how much may I stuff into it? Eg, if there is a 15U rack, can I really populate it with 15U of servers, or should I leave 1U at top and bottom for air circulation? Depth: Racks commonly have external depth of 600mm (network equipment), 800mm, 1000mm, or even longer. I'm trying to see how to fit into the 800mm depth. With reference to http://www.server-racks.com/rack-mount-depth.html, I'm hoping to have the front and rear posts mounted ~ 28.5" (72cm) apart, which would leave only 8cm for front space and rear space. How much rear space (from rear posts to back of rack) do I really need? I won't use cable management arms, so can I mount a 72cm depth server since the power, KVM, network cables won't take up much depth? My most important equipment are all < 60cm depth (4U chassis) and should comfortably fit within the 800mm cabinet. The rest of the equipment are very old 1U servers that range from 65-72cm depth. I might still want to make further use of them, or I might discard them since they are so old. Even if the 72cm servers cannot be powered on in an 800mm rack, I should be able to use them as 1U shelves. But, what server depth can I expect to be able to operate? Or am I forced to upgrade to 1000mm depth racks in order to use any servers deeper than 60cm? With reference to best practices for HP racks, some other specs and installation considerations: There aren't any minimum recommendations for clearance on the sides of the rack. It is recommended to leave 48" front clearance. The 48" front clearance is based on 32" chassis depth, 13" to extend the rack rails and mate the inner/outer rails, and 3" for movement. If I don't use such rails (eg, use shelves instead), it should be sufficient to leave front clearance of chassis depth + 3". It is recommended to leave 30" rear clearance "to provide space for servicing the rack". I'm planning to back the rack into a corner of the room, and wheel it slightly out when I need to access the rear. If the wheeling plan is ok, I still need to know how much rear clearance is required for air circulation and ventilation purposes. Castor wheels and stabilising feet. Since I'm backing the rack into a corner of the room, I'll only be able to set the stabilising feet on the front corners. Thoughts on safety? The rack that I'm considering has front glass doors with side ventilation slits and fully perforated rear doors. I'm hoping this will be a good balance between temperature and noise (only ventilation slits facing out the front, while the rear is facing the walls). Or is the sound of high-rpm fans going to escape through the front slits anyway and destroy my sanity?

  Read the article

• how to change interface ip in ifconfig with /etc/network/interfaces

  - by user2478348

  Hi everybody when modifiying /etc/network/interfaces, saving it and then executing ifconfig i can't see the modification i made..for example here is part of my /etc/network/interfaces: auto wlan1 iface wlan1 inet static address 192.168.0.60 netmask 255.255.255.0 gateway 192.168.0.61 you can see that the IP address of my wlan1 is 192.168.0.60 but when typing ifconfig i have this: wlan1 Link encap:Ethernet HWaddr 00:19:70:0f:c2:9c inet adr:192.168.0.1 Bcast:192.168.0.255 Masque:255.255.255.0 adr inet6: fe80::219:70ff:fe0f:c29c/64 Scope:Lien UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Packets reçus:758 erreurs:0 :0 overruns:0 frame:0 TX packets:610 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 lg file transmission:1000 Octets reçus:73490 (73.4 KB) Octets transmis:127883 (127.8 KB) (the inet adr:192.168.0.1 and not 198.168.0.60)..if someone can help me I'll be very thankful :)

  Read the article

• routing traffic between two network cards through firewall

  - by RubyFreak

  I'm trying to test a network device (firewall) using a Linux box, with two network cards, one interface connected to the WAN zone and another interface to LAN zone. The configuration is similar with that |ETH0| <-> | FW | <-> ETH1 So from both interfaces I'm able to ping the respective firewall interface. But i'm not able to fire something like: ping -I eth0 ip.from.eth1 and to get any answer. Is that possible or should the linux network namespace solution or user level tcp stacks (VMs are out of question)

  Read the article

• How do I keep a bridge enabled on a bonded interface?

  - by jlawer

  I'm working on setting up a pair of CentOS 6.3 servers that will run a couple of KVM vms and have come across a problem setting up a bridge on a bond. I am using Mode 4 (802.3ad) bonding on a pair of stacked Dell Powerconnect 5524 switches connecting to R320 servers. There are 2 links (1 to each switch) that form a Link Aggregation Group (802.3ad / LACP bonding). On top of the bond I have VLAN Tagging. I've verified this is a problem on multiple other bonding modes so it isn't just a mode 4 issue. I am testing what happens when 1 link is dropped (ie switch dies, cable breaks, etc). If I don't have a bridge (for KVM), everything works fine, failover happens as expected. If I have the bridge enabled, it works fine until failover (unplugging a cable). When failover happens /var/log/messages shows the slave link going down, followed within a second by: kernel: br1: port 1(bond0.8) entering disabled state The thing is /proc/net/bonding/bond0 shows the link is up as expected (simply with only 1 slave instead of 2). If I plug the cable back in it recovers and brings the bridge back to an enabled state. I actually have tested this while a ping is occuring and if the timing is right a packet will actually leave the system after the link is lost, but before the disabled message occurs. This disabled state I assumed was STP, but I have disabled STP on the bridge configuration and this issue still occurs. brctl showstp br1 still shows the link as disabled when it is running without a slave. I also switched between the nics in the server (I have 2x Broadcom & 4x intel). It doesn't matter which configuration I have. Does anyone know of a way to force the bridge to stay enabled or why its detecting the bond as disabled, when it isn't?

  Read the article

• Use router as external high powered Wi-Fi adapter

  - by skywinder

  I need a powerful external Wi-Fi adapter for a couple of days. I heard that some types of router support this mode, allowing me to connect the router to my notebook and just use it as an external Wi-Fi interface. Is it possible to connect a router as an external Wi-Fi adapter? How can I determine it? Updated: My purpose is to set the router to monitor mode and check networks around through my notebook to provide better configuration for my network (power, channels, etc). My internal notebook Wi-Fi adapter is too weak for this purpose. Should I use special drivers for that? If yes, can someone describe, step-by-step, how to do it? p.s. I want to use ASUS RT-N56U as an external Wi-Fi adapter on OS X or Ubuntu.

  Read the article

• What does "incoming" and "outgoing" traffic mean?

  - by mgibsonbr

  I've seen many resources explaining how to set up a server's firewall to allow incoming and outgoing traffic on HTTP standard ports (80 and 443), but I can't figure out why I would need either of them. Do I need to unblock both for a "regular" web site to work? For file uploads to work? Are there situations where it would be advisable to unblock one and leave the other blocked? Sorry if that's a basic question, but I couldn't find it explained anywhere (also I'm not a native english speaker). I know in a "regular" web site the client is always the one who initiates a request, so I'm assuming a web server must accept incoming traffic on those ports, and my common sense tells me the server is allowed to send a response without unblocking anything else (otherwise it wouldn't make sense to have two types of rules). Is that correct? But what is an outgoing web (service) traffic, and what would be its use? AFAIK if the server wanted to initiate a connection with another machine, the specific port that matters is the one in the other end (i.e. the destination port would be 80), on its end any free port could be used (the source port would be random). I can open HTTP requests from my server (using wget for instance) without unblocking anything. So I'm assuming my concepts of "incoming" and "outgoing" are wrong somehow.

  Read the article

• Turning on Bluetooth disables wifi on Yoga 2

  - by Yostage

  I have a Lenovo Yoga 2. The moment that I turn on bluetooth, the wifi drops out - I lose connection, and connecting again shows "connection failed". If I turn the bluetooth off, wifi can reestablish fine. I've tried lots of different combinations of drivers for both the wifi and the bluetooth, but no combination has has changed this behavior yet. I've read some speculation that the cards have insufficient shielding, but that seems like kind of a large flaw to ship with. I've tried with a Carbon X1, a Yoga 2 Pro, and a Yoga 2 all next to each other on the desk while running InSSIDer. The X1 and the Y2P don't lose wifi connection when the bluetooth turns on, but the Y2 does immediately. The Y2P and the Y2 are running the same drivers for bluetooth and wifi, and appear to have the same wireless card internally. During the failure state, InSSIDer still sees signal strength for my network, but I cannot connect to it. stats: the card that comes in the laptop is an Intel Wireless-N 7260 Intel Bluetooth driver is at 17.0.1401.422 Intel Wireless driver is at 17.0.2.5 Windows 8.1 x64 Home wifi is a Medialink MWN-WAPR150N

  Read the article

• TCPDump and IPTables DROP by string

  - by Tiffany Walker

  by using tcpdump -nlASX -s 0 -vvv port 80 I get something like: 14:58:55.121160 IP (tos 0x0, ttl 64, id 49764, offset 0, flags [DF], proto TCP (6), length 1480) 206.72.206.58.http > 2.187.196.7.4624: Flags [.], cksum 0x6900 (incorrect -> 0xcd18), seq 1672149449:1672150889, ack 4202197968, win 15340, length 1440 0x0000: 4500 05c8 c264 4000 4006 0f86 ce48 ce3a E....d@[email protected].: 0x0010: 02bb c407 0050 1210 63aa f9c9 fa78 73d0 .....P..c....xs. 0x0020: 5010 3bec 6900 0000 0f29 95cc fac4 2854 P.;.i....)....(T 0x0030: c0e7 3384 e89a 74fa 8d8c a069 f93f fc40 ..3...t....i.?.@ 0x0040: 1561 af61 1cf3 0d9c 3460 aa23 0b54 aac0 .a.a....4`.#.T.. 0x0050: 5090 ced1 b7bf 8857 c476 e1c0 8814 81ed P......W.v...... 0x0060: 9e85 87e8 d693 b637 bd3a 56ef c5fa 77e8 .......7.:V...w. 0x0070: 3035 743a 283e 89c7 ced8 c7c1 cff9 6ca3 05t:(>........l. 0x0080: 5f3f 0162 ebf1 419e c410 7180 7cd0 29e1 _?.b..A...q.|.). 0x0090: fec9 c708 0f01 9b2f a96b 20fe b95a 31cf ......./.k...Z1. 0x00a0: 8166 3612 bac9 4e8d 7087 4974 0063 1270 .f6...N.p.It.c.p What do I pull to use IPTables to block via string. Or is there a better way to block attacks that have something in common? Question is: Can I pick any piece from that IP packet and call it a string? iptables -A INPUT -m string --alog bm --string attack_string -j DROP In other words: In some cases I can ban with TTL=xxx and use that should an attack have the same TTL. Sure it will block some legit packets but if it means keeping the box up it works till the attack goes away but I would like to LEARN how to FIND other common things in a packet to block with IPTables

  Read the article

• Google account gives ERR_SSL_BAD_RECORD_MAC_ALERT errors

  - by Kjensen

  A couple of days ago, I started being unable to connect to accounts.google.com, which handles logins to all kinds of google services. I get this error in Chrome: Error 126 (net::ERR_SSL_BAD_RECORD_MAC_ALERT): Unknown error. In IE I get this: I assume it is the same error, just wrapped up. I run Win8 RTM. On the SAME machine, using the same network card, in a VMWare workstation image running Win7, I am able to connect perfectly. On another of my machines on my network, I am also still able to connect with no problem. My girlfriend uses the same network and has also complained a couple of times about this error (google calendar) - but this is anecdotal, since her technical troubleshooting abilities stop at "xxxx is broken". Her machine runs Win7. ;) I have rebooted, cleared cookies, do not run any antivirus/firewall, have not changed network config. The first 3-4 days after installing Win8, I did not have any problems. I have also searched, and found a hint about enabling SSL2.0 in connection settings, which did not help. Anybody know something about this error and what I can do to fix it?

  Read the article

< Previous Page | 194 195 196 197 198 199 200 201 202 203 204 205  | Next Page >