Search Results

Search found 19557 results on 783 pages for 'networking programming'.

Page 201/783 | < Previous Page | 197 198 199 200 201 202 203 204 205 206 207 208  | Next Page >

• Vista laptop won't connect to airport extreme

  - by Hutch

  Our previous router died, and to replace it I procured an apple airport extreme. My mac, my wrt54gs (with ddwrt acting as a bridge) and a linux machine have had no problem connecting to the wireless. None of the wired clients are having a problem obviously. The problem is one of my roommates can not connect. That's not strictly true. He can connect to the network, and will, infact, get a dhcp lease. However he cannot get any packets out. Can't ping the router, can't access any web sites, nothing. However he's fine if we switch to an unsecured network. Which is obviously not acceptable. The airport only allows for 'wpa/wpa2 personal' and 'wpa2 personal' (and of course the enterprise versions there of) I keep reading about this problem in multiple spots on the web, but never see any actual answers... Anyway the laptop: hp/compaq cq50-215nr vista home premium wireess card: atheros 5007 airport is simultaneos dualband II

  Read the article

• How can I connect to AS/400 through TN5250?

  - by Swati Sarkar

  How will I find out my iseries server name? I checked through "nslookup" it gives one ip address & I tried to connect TN5250 session to cconnect but could not connect. from dos command line c:\nslookup default server : unknown ip address : 192.168.50.119 Then I tried ping with this IP address - it's giving reply from the above IP address Then I have given this id in TN5250 session, but says can not create a connection to the AS/400.

  Read the article

• LAN speeds and firewall/switch connections

  - by microchasm

  I have a small network with about ten users. All workstations flow into a Dell PowerConnect 3424 which then has a single link to a SonicWALL firewall and from there to a cable modem. More important than internet connectivity is speed between machines (specifically a Windows Server box on the LAN which everyone uses simultaneously). I believe the 3424 has gigabit connections, but they look like they're for stacking. Is there a way to test the speeds on the LAN to see where the speeds are at? Is there any low-hanging fruit insofar as increasing speeds?

  Read the article

• How do I share a complete XP disk so it can be seen from a Windows 7 system?

  - by Ian Ringrose

  This should be easier! (both computers can see the internet etc so I know the network it’s self is working) I have a normal home network with a Windows XP machine on it and the new Windows 7 (64 bit) machine. So I can transfer the files to the new Windows 7 machine, I wish to share the complete disk (and all files) from the Windows XP machine and access them from the Windows 7 machine. Is there a step by step set of instructions for doing this anywhere? So fare I have: put both computers into the same workgroup put the windows 7 machine into work network mode so it can see the XP machine in the work group shared the XP disk as read only But when I try to access a lot of the folders on the XP disks, I am told I am not allowed to access them. (I was not asked for any passwords by the windows 7 machine when I accessed the XP machine. The XP machine just has its default account with no password set on it)

  Read the article

• Windows XP does not list WPA wireless networks

  - by Tomalak

  What can be the reason that Windows XP does not show WPA-encrypted wireless networks? The laptop I have problems with is an older model (Toshiba Satellite Pro 6100) with Windows XP SP3 on it, fresh install. The wireless network card in it is an Agere product that lists as "Toshiba Wireless LAN Mini PCI Card". The networks showed up perfectly before I first tried to connect to one (it was set to WPA2). The connection failed (the card supports WPA only), then something must have happend and Windows hides these networks now. A manually configured WPA setup via Windows' own wizard works, I'm using it right now. The network just won't show up in the list of available network on its own. I suspect that XP incorrectly set a flag somewhere that this network card does not support WPA. Is there such a flag, and if so, how can I change it back?

  Read the article

• Transient network dropout for Xen DomU's

  - by Stephen C

  We've got a CentOS server running a cluster of virtuals. Occasionally the cluster's internal network drops out for a minute or so ... and then comes back. The problem is somehow related to the actual network traffic, but it is not a simple load issue. (The system is generally lightly loaded, and the problem occurs irrespective of actual load.) The setup: CentOS 5.6 on Dom0, various CentOS on the DomU's Hardware - a Dell R710 with a BroadCom NextXpress 2 NIC (sigh) using the latest drivers for the NIC from BroadCom Xen configured to use network-bridge and vif-bridge Some iptable tweaks to route an unrelated port to one of the virtuals. The system has one externally visible IP address, and Dom0 runs an Apache httpd configured with a number of virtual hosts each of which reverse proxies to web servers running on the virtuals. (The virtuals have to be NAT'ed, primarily because we don't have enough allocated public IP addresses.) The symptoms: Works fine most of the time. When someone tries to UPLOAD a large file to one virtuals, the internal network drops out ... for all virtuals: The Dom0 httpd sees a network timeout talking to the backend server on the virtual and reports a 502. A previously established ssh connection from Dom0 to any of the DomU's freezes. Our monitoring shows ping failures for traffic between virtuals. The Xen consoles to the DomU's do not freeze. No log messages in any log files that I can see, on either Dom0 or the DomU's ... apart from the Dom0 httpd logs. After a minute or so, the problem clears by itself. This is 100% reproducible. What we've tried: Downloading, building and installing the latest BNX2 driver on Dom0 Turning off MSI on the NIC - adding "options bnx2 disable_msi=1" to /etc/modprobe.conf Turning off tcp segmentation offload - "ethtool -K eth0 tso off". Sacrificing a black rooster at midnight. I've exhausted all my options apart from switching to KVM ... or slaughtering more roosters. Any suggestions?

  Read the article

• How much packet loss is normal?

  - by Fabian

  I started monitoring our network using SmokePing. Users occasionally complain about bad network connections, but the problems went away after some minutes usually. I now wanted to get some more quantitative information about those problems. SmokePing regularly pings servers inside our network, in a connected network and outside hosts. I only have a limited amount of control over our internal network and none at all for the connection to the outside and to the second network. I now see quite often (2-4 times a day) that packets to the second network and the outside are dropped. Most of the times it is 1-2 packets out of 20, sometimes more. Inside our internal network no packets are dropped. Is this an expected amount of packet loss, or does it indicate that something is wrong? I'm mainly wondering if I should bother the university IT department about it, or if I should just accept it as it is.

  Read the article

• /etc/hosts.deny ignored in Ubuntu 14.04

  - by Matt

  I have Apache2 running on Ubuntu 14.04LTS. To begin securing network access to the machine, I want to start by blocking everything, then make specific allow statements for specific subnets to browse to sites hosted in Apache. The Ubuntu Server is installed with no packages selected during install, the only packages added after install are: apt-get update; apt-get install apache2, php5 (with additional php5-modules), openssh-server, mysql-client Following are my /etc/hosts.deny & /etc/hosts.allow settings: /etc/hosts.deny ALL:ALL /etc/hosts.allow has no allow entries at all. I would expect all network protocols to be denied. The symptom is that I can still web browse to sites hosted on the Apache web server even though there is a deny all statement in /etc/hosts.deny The system was rebooted after the deny entry was added. Why would /etc/hosts.deny with ALL:ALL be ignored and allow http browsing to sites hosted on the apache web server?

  Read the article

• How can I configure multiple default gateways on a CISCO Router?

  - by Spirit

  Does any one knows a way to configure a cisco router with multiple gateways - multiple gateways of last resort? I've tried adding a gateway of last resort twice (with different metric) but only one is shown: Router(config)# ip route 0.0.0.0 0.0.0.0 2.2.2.2 10 Router(config)# ip route 0.0.0.0 0.0.0.0 3.3.3.3 100 And the show ip route output was: Router# show ip route Gateway of last resort is 2.2.2.2 to network 0.0.0.0 2.0.0.0/24 is subnetted, 1 subnets C 2.2.2.0 is directly connected, FastEthernet0/0 3.0.0.0/24 is subnetted, 1 subnets C 3.3.3.0 is directly connected, FastEthernet0/1 32.0.0.0/30 is subnetted, 1 subnets C 32.2.2.0 is directly connected, Serial0/2/0 S* 0.0.0.0/0 [10/0] via 2.2.2.2 The point is that i cannot see the other route with higher distance metric? Anyone has a sugestion? I mean will this config work if the link on 2.2.2.2 fails? Will the router choose the other network 3.3.3.3, if the link 2.2.2.2 fails?

  Read the article

• Why don't mails show up in the recipient's mailspool?

  - by Jason

  I have postfix dovecot running with local email system on thunderbird. I have two users on by ubuntu, mailuser 1 and mailuser 2 whom i added to thunderbird. Everything went fine, except the users dont have anything on their inbox on thunderbird and sent mails dont get through. Im using maildir as well. Checking /var/log/mail.log reveals this This what is happining: Restarting postfix and dovecot and then sending mail from one user to another user... I believe this line is the problem May 30 18:31:55 postfix/smtpd[12804]: disconnect from localhost[127.0.0.1] Why is it not connecting ? What could be wrong ? /var/log/mail.log May 30 18:30:21 dovecot: imap: Warning: Killed with signal 15 (by pid=1 uid=0 code=kill) May 30 18:30:21 dovecot: master: Warning: Killed with signal 15 (by pid=1 uid=0 code=kill) May 30 18:30:21 dovecot: imap: Server shutting down. in=467 out=475 May 30 18:30:21 dovecot: config: Warning: Killed with signal 15 (by pid=1 uid=0 code=kill) May 30 18:30:21 dovecot: log: Warning: Killed with signal 15 (by pid=1 uid=0 code=kill) May 30 18:30:21 dovecot: anvil: Warning: Killed with signal 15 (by pid=1 uid=0 code=kill) May 30 18:30:21 dovecot: master: Dovecot v2.2.9 starting up (core dumps disabled) May 30 18:30:54 dovecot: imap-login: Login: user=<mailuser2>, method=PLAIN, rip=::1, lip=::1, mpid=12638, TLS, session=<xUfQkaD66gAAAAAAAAAAAAAAAAAAAAAB> May 30 18:31:04 postfix/master[12245]: terminating on signal 15 May 30 18:31:04 postfix/master[12795]: daemon started -- version 2.11.0, configuration /etc/postfix May 30 18:31:55 postfix/postscreen[12803]: CONNECT from [127.0.0.1]:33668 to [127.0.0.1]:25 May 30 18:31:55 postfix/postscreen[12803]: WHITELISTED [127.0.0.1]:33668 May 30 18:31:55 postfix/smtpd[12804]: connect from localhost[127.0.0.1] May 30 18:31:55 postfix/smtpd[12804]: 1ED7120EB9: client=localhost[127.0.0.1] May 30 18:31:55 postfix/cleanup[12809]: 1ED7120EB9: message-id=<[email protected]> May 30 18:31:55 postfix/qmgr[12799]: 1ED7120EB9: from=<[email protected]>, size=546, nrcpt=1 (queue active) May 30 18:31:55 postfix/local[12810]: 1ED7120EB9: to=<mailuser2@mysitecom>, relay=local, delay=0.03, delays=0.02/0.01/0/0, dsn=2.0.0, status=sent (delivered to maildir) May 30 18:31:55 postfix/qmgr[12799]: 1ED7120EB9: removed May 30 18:31:55 postfix/smtpd[12804]: disconnect from localhost[127.0.0.1] May 30 18:31:55 dovecot: imap-login: Login: user=<mailuser1>, method=PLAIN, rip=127.0.0.1, lip=127.0.0.1, mpid=12814, TLS, session=<sD9plaD6PgB/AAAB> This is my postfix main.cf See /usr/share/postfix/main.cf.dist for a commented, more complete version # Debian specific: Specifying a file name will cause the first # line of that file to be used as the name. The Debian default # is /etc/mailname. #myorigin = /etc/mailname smtpd_banner = $myhostname ESMTP $mail_name (Ubuntu) biff = no # appending .domain is the MUA's job. append_dot_mydomain = no # Uncomment the next line to generate "delayed mail" warnings #delay_warning_time = 4h readme_directory = no # TLS parameters smtpd_tls_cert_file=/etc/ssl/certs/ssl-cert-snakeoil.pem smtpd_tls_key_file=/etc/ssl/private/ssl-cert-snakeoil.key smtpd_use_tls=yes smtpd_tls_session_cache_database = btree:${data_directory}/smtpd_scache smtp_tls_session_cache_database = btree:${data_directory}/smtp_scache # See /usr/share/doc/postfix/TLS_README.gz in the postfix-doc package for # information on enabling SSL in the smtp client. smtpd_relay_restrictions = permit_mynetworks permit_sasl_authenticated defer_unauth_destination myhostname = server mydomain = mysite.com alias_maps = hash:/etc/aliases alias_database = hash:/etc/aliases myorigin = $mydomain mydestination = mysite.com #relayhost = smtp.192.168.10.1.com mynetworks = 127.0.0.0/8 [::ffff:127.0.0.0]/104 [::1]/128 192.168.10.0/24 mailbox_size_limit = 0 recipient_delimiter = + inet_interfaces = all home_mailbox = Maildir / mailbox_command= All ports are listening tcp 0 0 *:imaps *:* LISTEN tcp 0 0 *:submission *:* LISTEN tcp 0 0 *:imap2 *:* LISTEN tcp 0 0 s148134.s148134.:domain *:* LISTEN tcp 0 0 192.168.56.101:domain *:* LISTEN tcp 0 0 10.0.2.15:domain *:* LISTEN tcp 0 0 localhost:domain *:* LISTEN tcp 0 0 *:ssh *:* LISTEN tcp 0 0 *:smtp *:* LISTEN tcp 0 0 localhost:953 *:* LISTEN tcp6 0 0 [::]:imaps [::]:* LISTEN tcp6 0 0 [::]:submission [::]:* LISTEN tcp6 0 0 [::]:imap2 [::]:* LISTEN tcp6 0 0 [::]:domain [::]:* LISTEN tcp6 0 0 [::]:ssh [::]:* LISTEN tcp6 0 0 [::]:smtp [::]:* LISTEN tcp6 0 0 localhost:953 [::]:* LISTEN

  Read the article

• Can't connect to domain computers until reboot

  - by thealliedhacker

  I have a domain with about 300 Windows 7 and XP machines, with the domain controllers running Server 2003. Sometimes, I lose the ability to communicate/authenticate with some of the machines until I reboot my computer. This also happens from other computers and regardless of user account and operating system. In other words, say I'm on ComputerA, and I can't connect to ComputerX. I can go to ComputerB and connect to ComputerX, but ComputerB may not be able to connect to ComputerY. If you reboot ComputerA, then it will be able to connect to ComputerX again. Here are some messages from various utilities: sc: [SC] OpenSCManager FAILED 1722: The RPC server is unavailable. mmc (compmgmt.msc): Computer (computer name) cannot be managed. The network path was not found. explorer (\\computer): Windows cannot access \\(computer name). ping: Packets: Sent = 4, Received = 4, Lost = 0 (0% loss) / Average = 1ms

  Read the article

• Windows route two logical networks on one NIC

  - by John Oxley

  I have a Windows 2003 server which has one NIC with two networks configured on it. There are two logical networks sharing the same layer 2 domain. How do I configure the server to route traffic between the two logical networks?

  Read the article

• localhost name error with linux machines

  - by coderex

  Hi, CASE 1: I have a Ubuntu machine with name midhun.local I can access this in http://midhun.local/svn ... But its can't access from other machines(both Windows and Linux) through this host name. But it works with http://192.168.1.192/svn CASE 2: I have a another machine(windows) having the host-name myname:555 In this case i can access https://myname:555/svn from other windows machines with the same URL. But if am trying to access from the a Linux machine it will not work with the same URL instead of that https://192.1.168.111:555/svn will work. How can I solve the problem. I need to access via the same name from cross domain. How is it possible in LAN Thanks in advance!!

  Read the article

• Latency in TCP/IP-over-Ethernet networks

  - by aix

  What resources (books, Web pages etc) exist out there that: explain the causes of latency in TCP/IP-over-Ethernet networks; mention tools for looking out for things that cause latency (e.g. certain entries in netstat -s); suggest ways to tweak the Linux TCP stack to reduce TCP latency (Nagle, socket buffers etc). The closest I am aware of is this document, but it's rather brief. Alternatively, you're welcome to answer the above questions directly.

  Read the article

• Wirelss card not being detected in backtrack 5

  - by Jesse Nelson

  I just installed backtrack 5 and I am unable to detect my wireless card. iwconfig doesn't list my interface. I can see that the hardware is present in lspci -vnn (see below) but I can't get the interface detected. I have tried to reinstall the compat-wireless package but I get errors during the build (see below) I have done a ton of researching and I keep hitting a brick wall, mostly because the wiki for backtrack is down and I can't find any good resources. Does anyone know how to fix the issue? Also, does anyone no how I can scan the hardware to determine what NIC is assigning my interface? If I can figure out the interface name I think I can set it up manually by putting up the link and using wireless-tools to manually configure the connection, this is what I had to do in arch on my mac. As stated the wiki for backtrack is down and I can't find any help on the issue. I tried to do the full kernel upgrade suggested in my software update but after the update was complete and I logged back in I had a new log in manager and the only thing I was able to log into was window managers. However, after this update my wireless was working fine. Please help I am new to Linux and the wiki is down, I have nowhere else to turn. Forgot to mention I am using the KDE version, not Gnome. Thanks in advance for any help or support. Attempt at make: root@bt:/usr/src/compat-wireless-3.3-rc1-2# make /usr/src/compat-wireless-3.3-rc1-2/config.mk:254: "WARNING: CONFIG_CFG80211_WEXT will be deactivated or not working because kernel was compiled with CONFIG_WIRELESS_EXT=n. Tools using wext interface like iwconfig will not work. To activate it build your kernel e.g. with CONFIG_LIBIPW=m." make -C /lib/modules/2.6.38/build M=/usr/src/compat-wireless-3.3-rc1-2 modules make: *** /lib/modules/2.6.38/build: No such file or directory. Stop. make: *** [modules] Error 2 lspci output: root@bt:/usr/src/compat-wireless-3.3-rc1-2# lspci -vnn -i net lspci: I/O error at net, line 0 root@bt:/usr/src/compat-wireless-3.3-rc1-2# lspci -vnn 02:00.0 Network controller [0280]: Atheros Communications Inc. Device [168c:0032] (rev ff) (prog-if ff) !!! Unknown header type 7f ( This is the problem but I can't find the solution) Kernel modules: ath9k iwconfig output: root@bt:/usr/src/compat-wireless-3.3-rc1-2# iwconfig lo no wireless extensions. eth0 no wireless extensions.

  Read the article

• Why is it a bad idea to use multiple NAT layers or is it?

  - by iamrohitbanga

  The computer network of an organization has a NAT with 192.168/16 IP address range. There is a department with a server that has an IP address 192.168.x.y and this server handles hosts of this department with another NAT with the IP address range 172.16/16. Thus there are 2 layers of NAT. Why don't they have subnetting instead. This would allow easy routing. I feel multiple layers of NAT can cause performance losses. Could you please help me compare the two design strategies.

  Read the article

• CentOS/Apache killing connections

  - by fin1te

  Getting a really strange error. Basically, whenever I browse to my server (http://[ip_address] or http://[hostname]), it doesn't load, and my active SSH connection drops out. I installed CentOS 5.5, and then httpd and PHP 5.3. No other applications where installed, so I can't imagine it's something else causing it. I also reinstalled CentOS 5.5 again, completely fresh, the only thing I did to it was yum install httpd, and it still caused this issue. I've changed nothing in the config or anything else. Driving me mad, has anyone heard of this? It's really frustrating since everytime I attempt to debug this issue, I get kicked off SSH and have to log back in. Theres nothing in the Apache error logs, and nothing in the access log recording my attempt. Also, the result from uname - Linux [hostname] 2.6.35.4-rscloud #8 SMP Mon Sep 20 15:54:33 UTC 2010 x86_64 x86_64 x86_64 GNU/Linux Thank you

  Read the article

• Dnsmasq offering IP via DHCP, but nobody is accepting

  - by Matt

  As clients connect the logs light up with DHCPDISCOVER(wlan0) and DHCPOFFER(wlan0) but the IPs being offered are not being accepted. Currently dnsmasq offers IPs on eth1 which works flawlessly. It seems to be just wlan0 that poses this problem for me today. ifconfig of wlan0: wlan0 Link encap:Ethernet HWaddr aa:aa:aa:aa:aa:aa inet addr:10.0.0.2 Bcast:10.255.255.255 Mask:255.0.0.0 inet6 addr: fe80::baa3:86ff:fe70:796a/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:1609 errors:0 dropped:0 overruns:0 frame:0 TX packets:1268 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:308739 (301.5 KiB) TX bytes:319185 (311.7 KiB)

  Read the article

• Can I get simple name resolution on the local network without DNS, on a Mac?

  - by tim

  I've got Mantis running on a Linux VM with a Win2k8 server host. I installed Samba with the following configuration: [global] workgroup = COMPANY netbios name = MANTIS security = share Now on all our windows machines people can simple go to http://mantis, rather than http://172.16.0.20. However, this doesn't appear to work on the Mac machines. Any ideas how I can sort this without changing anything on the Windows server?

  Read the article

• How to use a home network patch panel?

  - by Torben Gundtofte-Bruun

  I'm planning a home network in a house that's not built yet. One recommendation is to add network sockets in various rooms and have them all end in a central place, where it all connects using a network switch. So far so good. Another recommendation says to not connect everything directly to the switch, but to a patch panel which in turn is connected to the switch. I'm unsure why this is good. Is there any practical advantage of using a patch panel if you're not planning to re-wire things very often? How does a patch panel actually work? Let's say it has 24 ports. Does it have another 24 ports on the backside that go to the switch, or what? Wikipedia isn't helpful on this. Clarification: I am planning to run network cables through conduits inside the walls and terminated with network sockets in the wall (as opposed to having just conduits and long regular network cables that have a normal plug in each end). Going by RedGrittyBrick's answer, a patch panel is nearly unavoidable in that case.

  Read the article

• Where are Wireless Profiles stored in Ubuntu

  - by LonnieBest

  Where does Ubuntu store profiles that allow it to remember the credentials to private wireless networks that it has previously authenticate to and used? I just replaced my Uncle's hard drive with a new one and installed Ubuntu 10.04 on it (he had Ubuntu 9.10 on his old hard drive. He is at my house right now, and I want him to be able to access his private wireless network when he gets home. Usually, when I upgrade Ubuntu, I have his /home directory on another partition, so his wireless profile to his own network persists. However, right now, I'm trying to figure out which .folder I need to copy from his /home/user folder on the old hard drive, to the new hard drive, so that he will be able to have wireless Internet when he gets home. Does anyone know with certainty, exactly which folder I need to copy to the new hard drive to achieve this?

  Read the article

• Windows 7, Printer is unavailable until PC reboot

  - by Cjs

  We are having a problem that I haven't seen before and can find no answers to online. A desktop running Windows 7 is unable to print using network printers. When the user tries, no matter what printer it is, he get's the following message when using Microsoft Office applications: "Current printer is unavailable. Select another printer." When the end user uses Outlook we get the message: "Printing is not available. There are no printers installed. You can select and configure a printer in Windows Control Panel." Now here is the confusing part, if we reboot the pc it works fine for a little while and then goes back to the same old same old. The printers are working fine for every other user as well so I believe it is the user's machine. If anyone has any ideas please let me know. Edit: I'd like to add in that some people were having luck disabling snmp for the printers. Restarting the print spooler doesn't seem to do anything.

  Read the article

• Monitor network traffic on a per-app basis in OS X?

  - by dougoftheabaci

  Title says it all. I'm looking for an app for OS X that will tell me what applications are using the network and what their in/out is. I can get most of the way there with LittleSnitch but it's the bandwidth part that it fails at. The only app I've come across that comes close is "Rubbernet" and while it does look like it would probably do what I want, it's very expensive (more than LittleSnitch) and doesn't look like it gets regular feature updates. Any recommendations?

  Read the article

• Network monitoring solution

  - by Hellfrost

  Hello Serverfault ! I have a big distributed system I need to monitor. Background: My system is comprised of two servers, concentrating and controlling the system. Each server is connected to a set of devices (some custom kind of RF controllers, doesnt matter to my question), each device connects to a network switch, and eventually all devices talk to the servers, the protocol between the servers and the devices is UDP, usually the packets are very small, but there are really a LOT of packets. the network is also somewhat complex, and is deployed on a large area physically. i'll have 150-300 of these devices, each generating up to 100+ packets per second, and several network switches, perhaps on 2 different subnets. Question I'm looking for some solution that will allow me to monitor all this mess, how many packets are sent, where, how do they move through the network, bandwidth utilization, throughput, stuff like that. what would you recommend to achieve this? BTW Playing nice with windows is a requirement.

  Read the article

• Waht are the best proxy servers for Mikrotik router?

  - by niren

  I want to setup proxy server for my Mikrotik router. There is inbuilt web-proxy for Mikrotik router but I can extend this upto transparent proxy(kind of proxy server) only. We need High anonymity proxy so that we can hide our LAN static IPs(we don't have private IP) from outside Intruder/hackers. And also I know I can setup NAT rule to hide our IP(only private IP not public/static IP) as per this link, but I cann't hide static/public IP. Essentially I want to hide our Public/Static IP (there is static/public IP for all systems in our company) from outside Internet. To achieve this I guess I need other software apart from Mikrotik router gateway setup. can anyone suggest me Is there any other software to achieve my requirement? I know about squid proxy but am not sure whether It can hide our static/public IP. Note: we have assigned public/Static IP to all systems of our company since we have rights to access our company's system from anywhere by dedicated laptop(given by our company with more security) through VPN connection.

  Read the article

< Previous Page | 197 198 199 200 201 202 203 204 205 206 207 208  | Next Page >