Search Results

Search found 6363 results on 255 pages for 'buford speed'.

Page 199/255 | < Previous Page | 195 196 197 198 199 200 201 202 203 204 205 206  | Next Page >

• Copying windows home server backup offsite

  - by Simon

  What ways are there to copy a windows home server backup to an offsite location? I'm talking specifically (and only) about the automated backup of my entire machine, and not the shared network folders. I am 90% working away from home on my laptop which has a 640GB drive so the shared folders are essentially useless to me. I backup every night, but if my house burns down or broken into the I'm in serious serious trouble ! I'm really looking for some alternative way to back up my entire machine - which much not interfere with the reliability or speed by which my WHS backs up my laptop every night. Either a way to 'export' a complete machine backup from the server, or recommendations on non-conflicting software I can backup to a 1TB drive at work are what I'm looking for. Note: I believe that WHS uses its own completely proprietary backup and doesn't use things like any 'backup bit' or 'archive bit'. I just dont want to install some other backup software that will conflict. PS I'm now running Windows 7 and just realized that I should probably check out the backup functionality it gives me. I assume that won't conflict right! Edit: Thanks for the hosted solutions. I'd also appreciate ways to backup to an 'offsite' location that I control - like my office vs. my home. The hosted solutions I think will be too slow or expensive for my needs.

  Read the article

• Could hybrid SSD + HDD be made with fixed internal partitions?

  - by Aaron

  I was pretty close to getting Seagate's Momentus XT but have been scared off by the many problems reported on forums and feedback sites, especially in Mac Book Pros. So I'm waiting for mk 2 with some extra flash and better reliablilty I'm assuming will come out this year. What would suit me better though is a 32+500 hybrid drive where I have more control over what is on the flash drive and what is on the disk drive. So there are 2 physical partitions within the one 2.5" hard drive enclosure which use different media internally (32GB for core files and 500GB for data and multimedia). The partitions would be locked so they can't be changed. - Or even better, the disk driver just makes them appear as two disks to the OS that share the same bus... Perhaps it's ok if the bios just sees the first drive until the OS is loaded. Is either of it technically possible? Obviously difficult to market outside of the enthusiast market. The SSD memory modules can be pretty small right, so they could even make them a card that plugs into a secondary connection on the enclosure. That would be good for computer builders as well as for upgrading and recoverability. Then future operating systems could recognise these system SSD drives and automatically install the OS + swap files on it. While placing document libraries on the larger data drive. While in the longer term HDD will probably disapear there will always be a trade off between speed, storage size and expense.

  Read the article

• Internet Troubles - PPPoE vs PPPoA?

  - by AkkA

  I have been having some internet troubles at home (ADSL2+ connection in Australia). We get random drop-outs from the authentication connection. It will keep the connection to the DSL service, but we lose authentication and either have to restart the router/modem (its combined, a Belkin one, not sure on model number) or unplug the phone cable, wait about 30 seconds and plug it in again. I've called the ISP (Telstra) a few times, but they only offer limited support when we dont use their supported hardware. Apparently something had happened on their side, they checked the box again (at least it sounded that simple), and told me it would be fine. It wasnt. I've replaced all the filters around the house, but that didnt help either. We do live a little bit away from the exchange (get a sync speed of about 3000/900), so I thought it could be due to line noise but that hasnt helped. Telstra allow both PPPoE and PPPoA connections (which I'm configuring through my router, dont have software on the PC side). I've been running PPPoA the whole time, would it make any difference changing it to PPPoE? If not, are there any other theories as to why we would be experiencing these drop-outs? It has been fine for at least 12 months, then suddenly started about 2 months ago.

  Read the article

• What are the replacement options for an IDE hard disk for a DOS based system?

  - by dummzeuch

  I have got a few "embedded" systems running MSDOS 6.2 which boot from and store data to IDE hard disks. Since these drives are nearing their end of life, the question arises how we can replace them. The requirements are: DOS must be able to install and boot from these drives. They must be able to sustain heavy (mostly) write access. If possible, they should be able to survive moderate vibrations (not too bad since the current hard disks have survived several years of that) I considered the following options so far: other ide hard drives: Unfortunately modern IDE drives are too large so DOS cannot boot from them even if I create small partitions. Older IDE drives are just that: old, so they are probably not the most reliable ones any more. SSDs: There are a few SSDs with IDE interface available. I have not yet tried them. Does anybody have any experience with them? They look like the ideal replacement provided that DOS can boot from them and that writing speed does not deteriorate too much (the old hard disks are no race cars either). Compact Flash: There are adapters for using CF with IDE controllers and they work fine. DOS can boot from them and they have no problems at all with vibrations. What I am not sure about is their durability. DOS uses FAT so some very few sectors are written every time the medium is being written to. IDE to SATA converters: I have no idea whether they are any good. Has anybody tried them? It might be an option to use one of these to connect an SATA SSD to the system. Are there any alternatives that I have missed? (We are working on replacing these systems, but it will still take a few years.)

  Read the article

• Caching/preloading files on Linux into RAM

  - by Andrioid

  I have a rather old server that has 4GB of RAM and it is pretty much serving the same files all day, but it is doing so from the hard drive while 3GBs of RAM are "free". Anyone who has ever tried running a ram-drive can witness that It's awesome in terms of speed. The memory usage of this system is usually never higher than 1GB/4GB so I want to know if there is a way to use that extra memory for something good. Is it possible to tell the filesystem to always serve certain files out of RAM? Are there any other methods I can use to improve file reading capabilities by use of RAM? More specifically, I am not looking for a 'hack' here. I want file system calls to serve the files from RAM without needing to create a ram-drive and copy the files there manually. Or at least a script that does this for me. Possible applications here are: Web servers with static files that get read alot Application servers with large libraries Desktop computers with too much RAM Any ideas? Edit: Found this very informative: The Linux Page Cache and pdflush As Zan pointed out, the memory isn't actually free. What I mean is that it's not being used by applications and I want to control what should be cached in memory.

  Read the article

• UW-IMAP server, high load for one user

  - by Bruce Garlock

  We have been experiencing a very strange anomaly, with one specific user with our UW-IMAP server. We have about 75 users using the server, and one particular user, who is in about the middle as far as used storage keeps having issues with slow speed. Most of our users all use Thunderbird 2, or Thunderbird 3. Mostly 2, because of the performance issues we have had with 3. This user was on 3, and I downgraded him to 2. The performance has gotten better, but according to the imapd processes on the server, his username is using the most CPU % and CPU time. I've already done all the usual T/S'ing: Started profile from scratch, compacted folders, re-indexed, newer faster computer, etc.. Still, this users' imapd process is always using the most CPU on the server. For troubleshooting, we setup another user which has more usage, folders, etc.. than he does, but we don't see the users process taking up most of the CPU with the imapd process. So, it almost sounds like a particular email may be the culprit, but how can we find it, if thats the problem? This has been going on for a while, and he is a management person, so his patience is about to end. Does anyone have any ideas?

  Read the article

• Wired to wireless bridge in Linux

  - by adrianmcmenamin

  I am attempting to set up my Raspberry Pi as a bridge (but I think this is not a question specific to the hardware) - using Debian wheezy. I have a hostapd.conf: (some details changed for security)... interface=wlan0 bridge=br0 driver=nl80211 auth_algs=1 macaddr_acl=0 ignore_broadcast_ssid=0 logger_syslog=-1 logger_syslog_level=0 hw_mode=g ssid=MY_SSID channel=11 wep_default_key=0 wep_key0=MY_KEY wpa=0 (yes, I know WEP is no good) And this in /etc/network/interfaces auto lo iface lo inet loopback iface eth0 inet dhcp allow-hotplug wlan0 iface wlan0 inet manual wpa-roam /etc/wpa_supplicant/wpa_supplicant.conf iface default inet dhcp auto br0 iface br0 inet dhcp bridge-ports eth0 wlan0 Everything seems to come up ok, but I cannot associate with the bridged wireless connection - even though the flashing lights on the USB stick suggest packets are being exchanged. I have read somewhere that not all cards/devices will run in hostap mode - they won't pass packets in one direction: is that right? (The info was a bit old)- this my card: [ 3.663245] usb 1-1.3.1: new high-speed USB device number 5 using dwc_otg [ 3.794187] usb 1-1.3.1: New USB device found, idVendor=0cf3, idProduct=9271 [ 3.804321] usb 1-1.3.1: New USB device strings: Mfr=16, Product=32, SerialNumber=48 [ 3.816994] usb 1-1.3.1: Product: USB2.0 WLAN [ 3.823790] usb 1-1.3.1: Manufacturer: ATHEROS [ 3.830645] usb 1-1.3.1: SerialNumber: 12345 So, what have I got wrong here?

  Read the article

• VPN sharing on Mac OS X 10.5 machine

  - by Jens

  I have a rather weird problem. I want to share a VPN connection that has been established by my Mac OS X 10.5 computer with another machine in my network. This is what I did: In the /etc/hostcongig file on the main computer I added the line: IPFORWARDING=-YES- I assigned a fixed IP address to my computer (192.168.178.30), a fixed one to the other machine (192.168.178.60) and my computer's IP address as gateway on the other machine. I connected to my VPN using the internal Mac OS X VPN client (PPTP connection) I run this script: #!/bin/sh natd -same_ports -use_sockets -unregistered_only -dynamic -interface ppp0 -clamp_mss ipfw -f flush ipfw add divert natd ip from any to any via ppp0 ipfw add pass all from any to any sysctl -w net.inet.ip.forwarding=1 Source: Using (and sharing) a VPN connection on your Mac Now everthing works smootly, however speed is an issue. I get 1,8 MBit/s on my main machine and only 0,3 - 0,6 MBit/s on the other one. My question: What could possibly be wrong? Do I have to tweak MTU settings, is there any packet inspection ongoing that needs time....? Any help appreciated!

  Read the article

• Using wildcard domains to serve images without http blocking

  - by iopener

  I read that browsers sometimes block waiting for multiple images from the same host, and I'm trying to do everything I can to speed up page load times. One caveat: I need to serve files over HTTPS. Any opinions about whether this is feasible: Setup a wildcard cert for *.domain.com. Whenever I need an image, generate an number based on a hash mod 5 of the filename, and append it to an 'img' subdomain (eg img1.domain.com, img4.domain.com, img3.domain.com, etc.); the hash will make any filename always use the same subdomain, and therefore the browser should be able to cache the images Configure a dynamic virtualhost record to point all img#. subdomains to /var/www/img I am looking for feedback about this plan. My concerns are: Will I get warnings when my page has https:// links to multiple subdomains? Is the dynamic virtualhost record I'm talking about even possible? Considering the amount of processing this would require, is it likely to even produce any kind of overall benefit? I'm probably averaging a half-dozen images per page, with only half being changed on each page refresh. Thanks in advance for you feedback.

  Read the article

• Accessing clearcase view drive from virtual machine is slow

  - by PermanentGuest

  I have a windows XP virtual machine running under a Windows XP host. On the host : On the host clearcase 7.1.1.2 is installed. I have a dynamic view mapped onto some drive. The view has certain VOB/directory structure where my application DLLs from the nightly build and config files are stored. I run my application on the host machine which uses the DLLs and config files from the VOB and everything runs smooth. Now I want to move this set-up to a virtual machine. On the guest : I'm running the guest with a vm-player. I don't want to install clear-case on this as I don't want to expose this machine onto the network. The network setting in the guest is 'host-only'. I have mapped the host's clearcase view drive as a shared folder and I'm able to access this drive from the virtual machine. Also, the application is running. However, the problem is that the access of the clearcase drive from the virtual machine is very slow. I can experience this from the windows explorer. Due to this, the starting of my application takes several seconds in the virtual machine while on the guest it comes up pretty fast. My question is : Is there any way to speed up the performance? I have managed to copy some of the DLLs which don't change frequently to the virtual machine to improve the performance. However, there are still lot of DLLs which have to be taken from the clearcase drive as they change frequently. VMplayer version is : VM Player 3.0.1 build-227600 Both guest and host is : Windows XP service pack 3 Host clearcase is : clearcase 7.1.1.2

  Read the article

• Nginx + WordPress + HHVM: Why isn't Batcache working? Would Varnish help even more?

  - by javipas

  I've heard great things about HHVM, so I've setup a copy of WordPress blog (on another domain) with Nginx (with the Pagespeed module) and HHVM. Right now the benefits are obvious: on the same config, load times are between two and three times faster. I'm trying to speed up things a little bit, and I've also installed Memcached and Batcache. I've installed the memcached package, copied object-cache.php (Pastebin) onto the root folder of the WordPress blog, and after that I've installed the Batcache plugin and copied the advanced-cache.php (Pastebin) file onto the wp-content folder. Also, I've included the line define('WP_CACHE', true); in the wp-config.php file. It seems it doesn't work, though. If I quickly reload the page several times Batcache should show the cached page, but it doesn't. It's easy to check that by reloading (Cmd+R on Chrome on OS X) the page several times and then viewing the page's code. Under the <head> section I should see some batcache stats, but they aren't there. I wonder if someone could give me some hint on this. On a side note, I don't know if I could add some other component in order to help the performance be even better. I'm thing about Varnish, but I'm not sure if it's just useless and it's just another way to the same I'm currently doing. Any other component there? (I'll test CDN for images, minifying js, etc and some other tricks as well, but I'm talking from the server perspective).

  Read the article

• explanation of RAM specs, and what do I need for a Gaming rig

  - by ewok

  I am looking into upgrading my custom built PC's RAM. I use the machine mostly for gaming, but I don't really know a ton about RAM, so I wanted to ask a few questions. The research I've done tells me there is a negligible increase in speed for anything above 1600 MHz. is this true or is it worth the extra money to go higher? Other than drawing more power from the PSU, is there any real difference in performance with different voltages (1.5V vs 1.65V)? most of the kits I've found in the 2x4 1600 range have a CAS latency of 9 and timing of 9-9-9-24. For a significant increase in price (usually about 1.5x), I can get either 8 or 7 and lower timing. Is it worth the cost? What I am looking for here is someone to give a good explanation of what the different specs represent, and how that relates to the performance of the machine. Specifically, I'm looking for what specs I need to focus on for a good gaming rig. I am NOT looking for a "buy this, it's the best RAM" without an explanation of why. The information will be much more valuable as it will allow me to make my own informed decision. As they say, give a man a fish, he'll eat for a day. teach a man to fish, and he'll eat for the rest of his life.

  Read the article

• Poor write performance on Debian server running NFS with 22TB exported JFS filesystem

  - by user143546

  I am currently running a debian server that is exporting a large JFS filesystem (22TB) over NFS (nfs-kernel-server.) When attempting to write to the NFS share, the performance is very poor. The 22TB disk is sitting on a NAS mounted using iSCSI. It will bust for a moment near expected line speed, and then sit idle for several seconds. Very little traffic measured in the low kb/sec. The wait peeks on write. When reading from the NFS mount, the system operates at expected speeds (11MB/sec). The issue does not occur when using SFTP, rsync, or local coping (non-nfs). The issue persists between stable and testing releases. On the same machine I have a 14TB ext4 filesystem using the exact same export configuration that does not share the issue. This share is not in regular use and thus not consuming resources. NFS Server: cat /etc/exports /data2 10.1.20.86(rw,no_subtree_check,async,all_squash) cat /sys/block/sdb/queue/scheduler noop [deadline] cfq cat /etc/default/nfs-kernel-server RPCNFSDCOUNT=8 RPCNFSDPRIORITY=0 RPCMOUNTDOPTS=--manage-gids NEED_SVCGSSD= RPCSVCGSSDOPTS= NFS Client: cat /etc/fstab 10.1.20.100:/data2 /root/incoming nfs rw,noatime,soft,intr,noacl 0 2 cat /sys/block/sdb/queue/scheduler noop [deadline] cfq cat /proc/mounts 10.1.20.100:/data2/ /root/incoming nfs4 rw,noatime,vers=4,rsize=262144,wsize=262144,namlen=255,soft,proto=tcp,port=0,timeo=600,retrans=2,sec=sys,clientaddr=10.1.20.86,minorversion=0,addr=10.1.20.100 0 0 This problem has me pretty stumped. Any help would be greatly welcomed. Thanks.

  Read the article

• Router vs switch in a LAN [closed]

  - by servernewbie

  If I have a LAN and and connect it with a switch, I understand it uses a CAM table to route packets in layer 2 (by saving mac to port relations). So far all good. However, when using a router for a LAN (ONLY for a LAN, not to connect it to "the outside" WAN/internet/etc) I get a bit confused as to how it internally processes packets. I would first split this into two router scenarios: Router with buit-in switch In this scenario, I would expect that it will act exactly as a switch with a CAM table internally. This would probably benefit a bit in speed (guessing here?) compared to the next option. Router without built-in switch Here is where I get confused. If hostA wants to send a packet to hostB, it will ARP to find hostB's MAC address and send it there. Now, if we had a switch (above scenario) this would be easy. But how does it work now in a router WITHOUT a switch? If I would guess, hostA would send an Ethernet frame with hostB's MAC address to the line. The router would fetch the packet (even though the router has another MAC address, it would still fetch this packet even if it only contains hostB's MAC address). It would strip the Ethernet frame header and check the IP, and then check its own internal ARP table again for the MAC address. Now, this would seem like a waste of resources compared to a router with a built-in switch. But maybe it does not work like that at all. Does it also contain a CAM table? If that would be true, what would then the difference between these two routers really be?

  Read the article

• Apache2: Limit simultaneous requests & throttle bandwidth per IP/client?

  - by xentek

  I want to limit simultaneous requests & throttle bandwidth per IP/Client on a single apache vhost. In other words, I want to ensure that this site, which hosts large media files, doesn't get hammered by someone trying to download everything all at once (just happened the other night). I'd like to limit the outgoing transfer speed overall for this site, as well as limit the number of connections a single IP can make to the server to a sane default (i.e. within normal browser limits for multiple requests so page loads aren't effected too much). Bonus points if I can actually scope it to file types (i.e. leave web files alone, but apply these rules to just the media files). We're running Ubuntu 9.04 on all the servers, and have two apache/php servers being load balanced via Round Robin by a squid proxy server. MySQL is running on its own box as well. We've got plenty of bandwidth to give them, so I don't really want overall caps, but just want to throttle the amount of memory/CPU it takes to serve this site. There other sites on these servers that we don't want to apply these rules too, just want to keep this one from hogging all the resources. Let me know if you need more info! Thanks in advance for your suggestions!

  Read the article

• ssh works fine when using public interface, but slow when using private interface

  - by Kevin M

  My Linux(UbuntuEEE) to Linux(CentOS) ssh takes a long time to log in(~15 seconds) when using the private interface, but not when using the public one. I have a Linux box acting as my router. As such, it has multiple interfaces(75.xxx.xxx.xxx, 192.168.1.1). I can ssh in from the internal interface(192.168.1.65 to .1), but it will take a while. I can ssh into the public address, and it goes quickly(~1 second). I have another box that I can ssh into the inside interface from and it goes quickly. iptables is set to accept packets coming into the interface immediately. sshd's UseDNS is normally on; I get the same problem if I turn it off and restart sshd. I normally use public-key authentication; I have done a mv ~/.ssh/ ~/ssh/ and it will ask me for a password after going slowly. After logging in(using either interface), speed is quick. ssh client version(via ssh -v):OpenSSH_4.7p1 Debian-8ubuntu1.2, OpenSSL 0.9.8g 19 Oct 2007 ssh server version(via rpm -qv openssh_server):openssh-server-4.3p2-29.el5

  Read the article

• Weird glitches on Intel iGPU

  - by FrederikVds

  I have a weird problem that I can't manage to describe in one word, so I'm having trouble searching for a solution. My monitors sometimes go black for a tenth of a second. Other times, they show the image shifted a few centimeters to the left or to the right. This happens on both of my monitors, but not necessarily at the same time. I would say it happens about once a minute, unless under heavy load, in which case it can happen every second or so. Interestingly, heavy CPU/memory usage can also cause this, not just heavy GPU usage. This only happens when they are both at 1920x1080, not when one of them, or both, are at a lower resolution. It also happens when they are in mirrored mode instead of extended desktop mode. My GPU is obviously not at full clock speed most of the time: this happens at 350 MHz as well as at 1200 MHz. So it doesn't seem like a matter of too little performance. I'm not seeing any traditional artefacts, even when I use MSI Kombustor, only this kind of full-screen glitches. CPU stressing software isn't reporting any issues either. I'm thinking maybe the connection between my CPU and my PCH isn't fast enough, but I can't find anyone with the same problem to confirm that. I'd rather not invest in a discrete GPU without being certain it will fix something. Does anyone know how to search for this, or even better, does anyone have a solution? My full specs are below. Thanks in advance! Specs: ASUS P8Z77-M Intel Core i5-3570K (with Intel HD 4000 Graphics) 2x4 GB AMD Performance Edition memory Corsair Force 3 Series Rev. B 120GB SSD Maxtor 200GB HD Lite-On DVD-RW Antec 350 Watt PSU 64-bit Windows 7 Professional 2x Iiyama ProLite E2208HDS display

  Read the article

• Can't mount Linux usb disk. It just create /dev/sg device but no /dev/sd

  - by MTilsted

  I have a Corsair R60 ssd disk which is a disk with both sata and usb connectors. But the usb thing seems to be a bit non-standard, or maybe its just my fedora linux. When I insert the disk using a usb cabel to a running Fedora 14 linux system, a device called /dev/sg3 is added but that is all. No new /dev/sd* device is created so I can't mount the disk. If I look at cat /proc/scsi/sg/device_strs I get ATA Hitachi HTS54321 FB2O HL-DT-ST DVDRAM GSA-T50N RP05 Seagate Desktop 0130 Corsair CSSD-R60GB2 So the disk is there. (The last entry) but my linux will for some reason not see it as a usb hard disk. When I insert other usb disks they work fine. It is only this specific disk which causes problems. I have tried on 3 different computers with the same result. A hint to the problem may be that if I add the disk to a windows system(With usb) the disk is called "A fixed disk" and not a portable disk as expected. The disk works fine with linux If i connect it with the sata cabel, but I would really like to have it working with usb too. (To mount it on computers without sata). Added: I did try to mount /dev/sg3 but mount say that its not a block device. (File say Its a character special device). Added output from dmesg: [ 97.454073] usb 7-1: USB disconnect, address 2 [ 105.913055] hub 2-0:1.0: unable to enumerate USB device on port 3 [ 107.048054] usb 2-3: new high speed USB device using ehci_hcd and address 5 [ 107.162900] usb 2-3: New USB device found, idVendor=1b1c, idProduct=1ab8 [ 107.162903] usb 2-3: New USB device strings: Mfr=1, Product=2, SerialNumber=5 [ 107.162906] usb 2-3: Product: CSSD-R60GB2 [ 107.162908] usb 2-3: Manufacturer: Corsair [ 107.162910] usb 2-3: SerialNumber: 10111441000000990069 [ 107.167651] scsi7 : usb-storage 2-3:1.0 [ 108.195543] scsi 7:0:0:0: Direct-Access Corsair CSSD-R60GB2 PQ: 1 ANSI: 0 [ 108.197732] scsi 7:0:0:0: Attached scsi generic sg3 type 0

  Read the article

• sysbench memory test on ec2 small instance

  - by caribio

  I'm seeing a problem with sysbench memory test (the default version that's compiled in). This is on Ubuntu Maverick, sysbench installed via apt-get install sysbench. Running the same thing on Ubuntu @ Rackspace worked just as expected. While the CPU and I/O tests worked fine on EC2 servers, the memory test just runs without doing anything (notice the 0M in the test results). The instance used was the publicly available 'stock' Ubuntu image with no changes to it: ./ec2-run-instances ami-ccf405a5 --instance-type m1.small --region us-east-1 --key mykey Supplying more arguments (such as: --memory-block-size=1K --memory-total-size=102400M) didn't help. What am I doing wrong? Thanks. sysbench --num-threads=4 --test=memory run sysbench 0.4.12: multi-threaded system evaluation benchmark Running the test with following options: Number of threads: 4 Doing memory operations speed test Memory block size: 1K Memory transfer size: 0M Memory operations type: write Memory scope type: global Threads started! Done. Operations performed: 0 ( 0.00 ops/sec) 0.00 MB transferred (0.00 MB/sec) Test execution summary: total time: 0.0003s total number of events: 0 total time taken by event execution: 0.0000 per-request statistics: min: 18446744073709.55ms avg: 0.00ms max: 0.00ms Threads fairness: events (avg/stddev): 0.0000/0.00 execution time (avg/stddev): 0.0000/0.00

  Read the article

• Netgear CG3000D new Modem/Router - Random High Ping

  - by justin.chmura

  Cox just recently came out and looked at my internet and decided that the modem I had was causing high latency issue. The speed was fine but the ping would spike to around 100 and over when gaming or putting a load more than browsing on the line. After they replaced it, it seems like I get better latency, but when it spikes, I get upwards of over 300 ping with like 500 jitter. I figured I would hit the serverfault universe before sending another email to Cox. I opted not to do the Cox setup as it was an extra $20 which I thought would have just setup the wireless (which I can handle). Is it a setting or something that I missed that needs to be setup? The firmware for the CG3000D is awful and not fun to use. I did change some hidden settings on the RgServices.asp page (I'll attach a screenshot). I've also heard that the Router/Modem combos are awful and that I should go back and just ask for a modem stand-alone. Any input is helpful. All screenshots: http://imgur.com/a/JX6qu#0

  Read the article

• Server 2008 RAID 5 Write Speeds

  - by Solipsism

  I recently configured a RAID 5 partition in Server 2008 with 4 RAID 5 disks. These disks are connected through a SATA expansion card that uses PCIe. This morning, I checked and they had finally finished synchronizing, and so I tried to do some speed tests. Copying off the disks started pretty much fine - speeds began at 125MB/s, then trailed down to about 70MB/s, which I found odd but not worrying. Writing TO the disks however is a completely different story. I attempted to copy some of my VM host ISOs onto the disks (~2-4 GB apiece) and this resulted in speeds of approximately 10MB/s. I tried copying both from a local disk (connected directly to the motherboard) and from another server ththe gigabit network and results were the same. I checked the performance monitor while transferring the files and the only thing that stuck out was that my memory hard faults shot up to 6,000 per minute (spiking around 200/s) by explorer.exe. The system is running 2GB of DDR667 ECC RAM and a quad-core 2.3GHz opteron. Is there anything I can do to fix this performance issue (buy more RAM? move the drives to a faster box?, etc) or am I just screwed so long as I stick to windows.

  Read the article

• xen + debian network after upgrade squeeze to wheeze

  - by rush

  I've got a Debian + Xen server. After a system upgrade to the stable version the network doesn't come up after boot. Every time after reboot I need to bring it up manually. The network configuration was not changed during upgrade. Here is /etc/network/interfaces: auto lo iface lo inet loopback auto eth0 iface eth0 inet static address 11.22.33.44 netmask 255.255.255.0 gateway 11.22.33.1 nameserver 8.8.8.8 After boot ip r shows no route and eth0 has no ip address. Manually ip and route setup goes fine and network starts working. Messages from dmesg about network I've found (looks like nothing interesting) [ 3.894401] ACPI: Fan [FAN3] (off) [ 3.894444] ACPI: Fan [FAN4] (off) [ 4.178348] e1000e 0000:00:19.0: eth0: (PCI Express:2.5GT/s:Width x1) 00:1e:67:14:66:c9 [ 4.178351] e1000e 0000:00:19.0: eth0: Intel(R) PRO/1000 Network Connection [ 4.178392] e1000e 0000:00:19.0: eth0: MAC: 10, PHY: 11, PBA No: 0100FF-0FF [ 4.178413] e1000e 0000:02:00.0: Disabling ASPM L0s L1 [ 4.178432] xen: registering gsi 16 triggering 0 polarity 1 -- [ 4.223667] ata5: DUMMY [ 4.223668] ata6: DUMMY [ 4.289153] e1000e 0000:02:00.0: eth1: (PCI Express:2.5GT/s:Width x1) 00:1e:67:14:66:c8 [ 4.289155] e1000e 0000:02:00.0: eth1: Intel(R) PRO/1000 Network Connection [ 4.289245] e1000e 0000:02:00.0: eth1: MAC: 3, PHY: 8, PBA No: 1000FF-0FF [ 4.506908] usb 1-1: new high-speed USB device number 2 using ehci_hcd [ 4.542920] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300) -- [ 10.362999] EXT4-fs (dm-23): mounted filesystem with ordered data mode. Opts: (null) [ 10.419103] EXT4-fs (dm-3): mounted filesystem with ordered data mode. Opts: (null) [ 10.988255] ADDRCONF(NETDEV_UP): eth1: link is not ready [ 13.175533] Event-channel device installed. [ 13.287555] XENBUS: Unable to read cpu state -- [ 13.288670] XENBUS: Unable to read cpu state [ 13.965939] Bridge firewalling registered [ 14.134048] e1000e: eth1 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: Rx/Tx [ 14.283862] ADDRCONF(NETDEV_UP): peth0: link is not ready [ 14.284543] ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready [ 17.800627] e1000e: peth0 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: Rx/Tx [ 17.801377] ADDRCONF(NETDEV_CHANGE): peth0: link becomes ready [ 18.307278] device peth0 entered promiscuous mode [ 24.538899] eth1: no IPv6 routers present [ 28.570902] peth0: no IPv6 routers present I've upgraded two servers and I've such behaviour on two of them. How to fix this and get network starts automatically on boot?

  Read the article

• Is there an objective way to measure slowness of PC/WINDOWS?

  - by ekms

  We've a lot of users that usually complain about that his PC is "slow". (we use win XP). We usually check startup programs, virus, fragmentation, disk health and common problems that causes slowness (Symantec AV drops disk to 1mb/s , or a seagate HD firmware error in certain models), but in those cases the slowness is pretty evident. In other hand, the most common is the user complaining about his pc but for us looks OK, even in 6 years old desktops. People sometimes even complains about his new quad core desktops speed!!! So, we are asking if there's a way to OBJECTIVELY check that a computer didn't dropped its performance, compared with similar ones o previous measures, specially for work use (I don't think that 3dmark benchmark o similar may help). The only thing that I found that was useful is HDTune, but it only check hard disk performance. Basically, what we want is something that enable us to say to our users "see? your PC is as slow as was three years ago! stop complaining! Is all in your head!"

  Read the article

• Network switches for LAN party

  - by guywhoneedsahand

  I am working on setting up the network for a small LAN party (less than 16 people). Most of them do not have wireless cards in their rigs, so I need to set up some way for everyone to a) play LAN games and b) access the internet. The LAN party will probably take place in my basement, where I have enough space. However, the basement is not wired up with the router which is actually on the floor above. I make a cantenna a while back that can boost the wireless performance of my computer significantly. How can I use this to provide internet and LAN to guests? My hope was that I could use a switch like this http://www.newegg.com/Product/Product.aspx?Item=N82E16833181166 for the LAN - but how can I give people access to the internet? Is there such thing as a network extender / 16-port switch? Obviously, the internet performance doesn't need to be super stellar, because the games will be using LAN - so I am looking to provide some usable internet for web browsing, and very high speed LAN for games. Thanks!

  Read the article

• How to verify system using right GPU, after system reset [duplicate]

  - by Antoros

  This question already has an answer here: Is my mobile AMD card being used? 2 answers OS: Windows 8 CPU: Intel® Core™ i7 Processor 3635QM GPU 1 : Intel HD Graphics 4000 GPU 2 : AMD Radeon™ HD 8870M other info: System Spects Problem: im unsure that CCC is using AMD card instead of Intel's, i have encountered several issues since updating to 8.1 and i don't know what to do What happened: Installed 8.1 patch first day After 1 minute of use, BBSOD, windows never loaded again System restore wouldnt recognize 8.0 restore points i did a system reset to windows 8 since the laptop was only 3 weeks old System Broke, it did restore to factory BUT kept the registry almost intact, i had to install almost everything again, since the factory drivers where working with the updated one's registry and several problems CCC Broke too <- What i've already done Installing new drivers on top of old ones didnt work, so i used AMD uninstaller first Uninstalled and Re-installed Intel's HD Graphics Driver Tried to install mobile center, but AMD told me that it wasnt compatible (even if thats the only driver that they provide via their page as seen Here) Tried to use Auto-Detect, couldnt install driver because card was disabled because it didnt have the drivers... (see what they did here?) Had to use a workaround with Samsung Update, the driver didnt appear as download so had to use search and downloaded the driver manually. Now the graphic card appears on device manager and catalyst but as 8800 series (not exact model), and cant check the card with neither dxdiag/GPU-z/HWMonitor when right-clicking on CCC only Intel card appears launching a game and using as "high performance" would speed it up a little but i cant be sure How to verify its working properly? HWMonitor wont show AMD card even when set to high performance Latest GPU-Z wont work because a problem with Intel's, and legacy ones wont either what can I do now? I don't even know if I fixed my problem or not, and i also want to to use Adobe Premier with it, and its locked (the option to run it with the amd card not intels) Edit: now it seems to work, but cant change the setting for adobe Premiere and other programs that i Need to

  Read the article

< Previous Page | 195 196 197 198 199 200 201 202 203 204 205 206  | Next Page >