Search Results

Search found 21884 results on 876 pages for 'external address'.

Page 2/876 | < Previous Page | 1 2 3 4 5 6 7 8 9 10 11 12  | Next Page >

  • "The daemon is being inhibited" error message when mounting volumes on a partitioned external HD [closed]

    - by Todd
    I'm having a great deal of difficulty with an external hard drive. I'm currently running a dual boot system (XP Service Pack 3 and Ubuntu 11.04 Natty Narwahl) on a Dell Inspiron B120. I'm trying to set up a new 80 GB Hitachi external HD. Using GParted, I formatted the drive and set up the partitions. The partitioning scheme is as follows 10GB NTFS Primary, 2GB Linux-Swap Primary, 50GB FAT32 Primary, 12GB Unallocated. After applying those changes, I went into Disk Utility and the HD appears along with the correct partitions. When I try to mount the volumes for partitions 1 and 3, I get a pop-up stating: Error Mounting Volume An error occurred while performing an operation on "Home" (Partition 3 of HTS548080m9AT00): The daemon is being inhibited. When I try to to check the filesystem I get a pop-up stating: Error Checking filesystem on volume An error occurred while performing an operation on "Home" (Partition 3 of HTS548080m9AT00): The daemon is being inhibited. Throughout the time that I'm attempting to troubleshoot the problem, the external drive light is on and blinking. With my frustration hitting a boiling point, I try to shut down the drive and remove it so that I can plug in a different external HD that works PERFECTLY. However, when I try to shut down and safely remove the drive, I get a pop-up stating: Error Detaching Drive An error occurred while performing an operation on "80GB Hard Disk" (HTS548080m9AT00): The daemon is being inhibited. Can anyone tell me what I'm doing wrong? I'm a newbie and not that skilled with terminal commands, so please dumb it down for me if you request specific command output.

    Read the article

  • Difficulty Mounting Volumes on a Partitioned External HD

    - by Todd
    I'm having a great deal of difficulty with an external hard drive. I'm currently running a dual boot system (XP Service Pack 3 and Ubuntu 11.04 Natty Narwahl) on a Dell Inspiron B120. I'm trying to set up a new 80 GB Hitachi external HD. Using GParted, I formatted the drive and set up the partitions. The partitioning scheme is as follows 10GB NTFS Primary, 2GB Linux-Swap Primary, 50GB FAT32 Primary, 12GB Unallocated. After applying those changes, I went into Disk Utility and the HD appears along with the correct partitions. When I try to mount the volumes for partitions 1 and 3, I get a pop-up stating: Error Mounting Volume An error occurred while performing an operation on "Home" (Partition 3 of HTS548080m9AT00): The daemon is being inhibited. When I try to to check the filesystem I get a pop-up stating: Error Checking filesystem on volume An error occurred while performing an operation on "Home" (Partition 3 of HTS548080m9AT00): The daemon is being inhibited. Throughout the time that I'm attempting to troubleshoot the problem, the external drive light is on and blinking. With my frustration hitting a boiling point, I try to shut down the drive and remove it so that I can plug in a different external HD that works PERFECTLY. However, when I try to shut down and safely remove the drive, I get a pop-up stating: Error Detaching Drive An error occurred while performing an operation on "80GB Hard Disk" (HTS548080m9AT00): The daemon is being inhibited. Can anyone tell me what I'm doing wrong? I'm a newbie and not that skilled with terminal commands, so please dumb it down for me if you request specific command output.

    Read the article

  • external display in Ubuntu 13.04

    - by thuc2009
    I have had a look on series of similar topics but I could not find a right answer. Currently, I bought laptop Dell latitude E6530 and installed Ubuntu 13.04 (64 bit) alongside with Windows 7 (I could not get rid of it because of some special programs for work). Ubuntu worked well, however, it did not detect the external displays (Dell 23" and Dell 19") no matter I plugged them before or after booting. Edited: I connected my laptop to those external displays through a laptop dock. I went to Settings- Display, the displays were there, but when I enabled them, Ubuntu logged off automatically. No external display was detected. In addition, the laptop screen sometimes was detected as Dell 23" I got an advice from similar topic that nvidia driver should be updated to version 313 or 319. I upgraded driver and the unity launcher disappeared, main display resolution turned to 640*480 and none of external displays was detected. I tried to use additional drivers, but when I turned it on, it told me that there was no driver to be used. Could some one tell me what should I do ? Edited : options vmwgfx enable_fbdev=1

    Read the article

  • Using External Monitor with Laptop Monitor as separate monitors

    - by user14623
    I am trying to use 32"LCD monitor with my ubuntu 10.10 installation. I am trying to use my laptop screen and external monitor at the same time but having two separate desktops. I also want to use my laptop with 1280x800 resolution and external one with 1920 x 1080 using VGA. However, ubuntu sees my external LCD as a CRT and provide 13....x... resolution at the best not above. My graphics card driver is Nvidia 270.... driver. Is ubuntu capable of using two monitors separately or should i give up? Thank you

    Read the article

  • Can't copy from hfs+ external

    - by Janine
    I've spent days and days trying to figure this out, but still can't. I think I've read every article on this and tried all there is to try, and I still can't copy any file from my mac-formatted hfs+ external drive. Sorry if there's still an article I've missed.. I have disabled journaling and tried all the hfsprogs commands I could find, but still whenever I click on a folder on the external and try to copy it to my home directory, I get this: "The folder xxx cannot be handled because you don't have permission to read its content." I then found an article about inoring this by copying files through the Terminal. When trying to run the sudo cp -r command in the Terminal with my external drive path, I always get 'no such file or directory'.. Does anyone have another suggestion for me? Thanks in advance!

    Read the article

  • Can't mount external hard drive

    - by tezza
    i have a problem accessing the data on my external hard drive. I recently did a fresh install but mistakenly left my external hard drive plugged in. When I tried to access the data on the external HDD, it says "no files" but recognizes that there is 290 GiB of data on it. The HDD is 350GB big. I checked the drive with Disk Utility and it showed that the hard drive had a bootable flag. So, in the edit partition, I unchecked this bootablity. Now it won't mount in Ubuntu and now my XP can't recognize it at all, whereas I could access the data on the XP machine before. In disk utility, it doesn't give me the option to check the bootable box in again and I can't access the data on XP either. Any ideas on how to fix it?

    Read the article

  • Error mounting an external HDD

    - by Slash
    I want to mount an external HDD.I have tried many things but still no success.When i try to mount it from Disk Utility i get this error: Error mounting: mount exited with exit code 1: helper failed with: Unprivileged user can not mount NTFS block devices using the external FUSE library. Either mount the volume as root, or rebuild NTFS-3G with integrated FUSE support and make it setuid root. Please see more information at tuxera.com/community/ntfs-3g-faq/#unprivileged

    Read the article

  • Icons of external devices not appearing on Desktop in 12.04

    - by harisibrahimkv
    In 10.04 and all, when a pen drive or as for that matter, when any external devices are connected, their icons are shown on the desktop and nautilus pops up automatically too. But in my 12.04 Gnome classic, when I connect an external device, nothing happens. I have to open nautilus manually and then click on the icon in the left panel to access the folder of the device. Is there any way to rectify this and restore the old trait as in 10.04?

    Read the article

  • Using events in an external swf to load a new external swf

    - by wdense51
    Hi I'm trying to get an external swf to load when the flv content of another external swf finishes playing. I've only been using actiosncript 3 for about a week and I've got to this point from tutorials, so my knowledge is limited. This is what I've got so far: Code for External swf (with flv content): import fl.video.FLVPlayback; import fl.video.VideoEvent; motionClip.playPauseButton = player; motionClip.seekBar = seeker; motionClip.addEventListener(VideoEvent.COMPLETE, goNext); function goNext(e:VideoEvent):void { nextFrame(); } And this is the code for the main file: var Xpos:Number=110; var Ypos:Number=110; var swf_MC:MovieClip = new MovieClip(); var loader:Loader = new Loader(); var defaultSWF:URLRequest = new URLRequest("arch_reel.swf"); addChild (swf_MC); swf_MC.x=Xpos swf_MC.y=Ypos loader.load(defaultSWF); swf_MC.addChild(loader); //Btns Universal Function function btnClick(event:MouseEvent):void{ SoundMixer.stopAll(); swf_MC.removeChild(loader); var newSWFRequest:URLRequest = new URLRequest("motion.swf"); loader.load(newSWFRequest); swf_MC.addChild(loader); } function returnSWF(event:Event):void{ swf_MC.removeChild(loader); loader.load(defaultSWF); swf_MC.addChild(loader); } //Btn Listeners motion.addEventListener(MouseEvent.CLICK,btnClick); swf_MC.addEventListener(swf_MC.motionClip.Event.COMPLETE,swf_MC.motionClip.eventClip, returnSWF); I'm starting to get an understanding of how all of this works, but it's all to new to me at the moment, so I'm sure I've approached it from the wrong angle. Any help would be fantastic, as I've been trying at this for a few days now. Thanks

    Read the article

  • eeePC 1001HA/1101HA max resolution when connected to external display?

    - by Marco Demaio
    Hello, I would like to buy a new Eee PC 1001HA or 1101HA. I know the max display resolution is: 1024x600 for eeePC 1001 and 1366x768 for eeePC 1101 But what's the max resolution of the graphic board when connecting these two types of eeePC to an external LCD monitor??? Let's say the external LCD monitor supports a full HD resolution of 1920x1080, are these eeePC graphic boards able to go up to such resolution??? It's really incredible to me, how such a useful information is missing everywhere on every ASUS website. Eee PC are very well suited to be connected to external monitor, so I can't believe how difficult is to find out this information. I downloaded aldo the manual, but it's not in there too. So I was hoping somone has got one and knows the answer. Thanks!

    Read the article

  • Windows Server 2008: specifying the default IP address when NIC has multiple addresses

    - by Cédric Boivin
    I have a Windows Server which has ~10 IP addresses statically bound. The problem is I don't know how to specify the default IP address. Sometimes when I assign a new address to the NIC, the default IP address changes with the last IP entered in the advanced IP configuration on the NIC. This has the effect (since I use NAT) that the outgoing public IP changes too. Even though this problem is currently on Windows Server 2008 How can you set the default IP address on a NIC when it has multiple IP addresses bound? There is more explication on my probleme. Here is the ipconfig DHCP Enabled. . . . . . . . . . . : No Autoconfiguration Enabled . . . . : Yes IPv4 Address. . . . . . . . . . . : 192.168.99.49(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.0 IPv4 Address. . . . . . . . . . . : 192.168.99.51(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.0 IPv4 Address. . . . . . . . . . . : 192.168.99.52(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.0 IPv4 Address. . . . . . . . . . . : 192.168.99.53(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.0 IPv4 Address. . . . . . . . . . . : 192.168.99.54(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.0 IPv4 Address. . . . . . . . . . . : 192.168.99.55(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.0 IPv4 Address. . . . . . . . . . . : 192.168.99.56(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.0 IPv4 Address. . . . . . . . . . . : 192.168.99.57(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.0 IPv4 Address. . . . . . . . . . . : 192.168.99.58(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.0 IPv4 Address. . . . . . . . . . . : 192.168.99.59(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.0 IPv4 Address. . . . . . . . . . . : 192.168.99.60(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.0 IPv4 Address. . . . . . . . . . . : 192.168.99.61(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.0 IPv4 Address. . . . . . . . . . . : 192.168.99.62(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.0 IPv4 Address. . . . . . . . . . . : 192.168.99.64(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.0 IPv4 Address. . . . . . . . . . . : 192.168.99.65(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.0 IPv4 Address. . . . . . . . . . . : 192.168.99.66(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.0 IPv4 Address. . . . . . . . . . . : 192.168.99.67(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.0 IPv4 Address. . . . . . . . . . . : 192.168.99.68(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.0 IPv4 Address. . . . . . . . . . . : 192.168.99.70(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.0 IPv4 Address. . . . . . . . . . . : 192.168.99.71(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.0 IPv4 Address. . . . . . . . . . . : 192.168.99.100(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.0 IPv4 Address. . . . . . . . . . . : 192.168.99.108(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.0 IPv4 Address. . . . . . . . . . . : 192.168.99.109(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.0 IPv4 Address. . . . . . . . . . . : 192.168.99.112(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.0 IPv4 Address. . . . . . . . . . . : 192.168.99.63(Duplicate) Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : 192.168.99.1 If i do a pathping there is the answer, the first up is the 99.49, also if my default ip is 99.100 Tracing route to www.l.google.com [72.14.204.99] over a maximum of 30 hops: 0 Machine [192.168.99.49] There is the routing table on the machine Network Destination Netmask Gateway Interface Metric 0.0.0.0 0.0.0.0 192.168.99.1 192.168.99.49 261 10.10.10.0 255.255.255.0 On-link 10.10.10.10 261 10.10.10.10 255.255.255.255 On-link 10.10.10.10 261 10.10.10.255 255.255.255.255 On-link 10.10.10.10 261 192.168.99.0 255.255.255.0 On-link 192.168.99.49 261 192.168.99.49 255.255.255.255 On-link 192.168.99.49 261 192.168.99.51 255.255.255.255 On-link 192.168.99.49 261 192.168.99.52 255.255.255.255 On-link 192.168.99.49 261 192.168.99.53 255.255.255.255 On-link 192.168.99.49 261 192.168.99.54 255.255.255.255 On-link 192.168.99.49 261 192.168.99.55 255.255.255.255 On-link 192.168.99.49 261 192.168.99.56 255.255.255.255 On-link 192.168.99.49 261 192.168.99.57 255.255.255.255 On-link 192.168.99.49 261 192.168.99.58 255.255.255.255 On-link 192.168.99.49 261 192.168.99.59 255.255.255.255 On-link 192.168.99.49 261 192.168.99.60 255.255.255.255 On-link 192.168.99.49 261 192.168.99.61 255.255.255.255 On-link 192.168.99.49 261 192.168.99.62 255.255.255.255 On-link 192.168.99.49 261 192.168.99.64 255.255.255.255 On-link 192.168.99.49 261 192.168.99.65 255.255.255.255 On-link 192.168.99.49 261 192.168.99.66 255.255.255.255 On-link 192.168.99.49 261 192.168.99.67 255.255.255.255 On-link 192.168.99.49 261 192.168.99.68 255.255.255.255 On-link 192.168.99.49 261 192.168.99.70 255.255.255.255 On-link 192.168.99.49 261 192.168.99.71 255.255.255.255 On-link 192.168.99.49 261 192.168.99.100 255.255.255.255 On-link 192.168.99.49 261 192.168.99.108 255.255.255.255 On-link 192.168.99.49 261 192.168.99.109 255.255.255.255 On-link 192.168.99.49 261 192.168.99.112 255.255.255.255 On-link 192.168.99.49 261 192.168.99.255 255.255.255.255 On-link 192.168.99.49 261 224.0.0.0 240.0.0.0 On-link 192.168.99.49 261 224.0.0.0 240.0.0.0 On-link 10.10.10.10 261 255.255.255.255 255.255.255.255 On-link 192.168.99.49 261 255.255.255.255 255.255.255.255 On-link 10.10.10.10 261 How i can be sure the ip use in the image ( suppose to be the default ip address ) will be use by my server as the default address ?

    Read the article

  • How to distinguish a NY "queens-style" street address from a ranged address, and an address with a u

    - by feroze
    I need to distinguish between a Queens style address, from a valid ranged address, and an address with a unit#. For eg: Queens style: 123-125 Some Street, NY Ranged Address: 6414-6418 37th Ln SE, Olympia, WA 98503 Address with unit#: 1990-A Gildersleeve Ave, Bronx, NY. In the case of #3, A is a unit# at street address 1990. THe unit# might be a number as well, for eg: 1990-12. A ranged address identifies a range of addresses on a street, and not a unique deliverable address. So, the question is, is there an easy way to identify the Queens style address from the other cases?

    Read the article

  • Can't boot Ubuntu 12.04 from external Hard Drive using Mac

    - by Catgirl the Crazy
    Recently, I upgraded the RAM and hard drive on my Early 2008 Macbook to improve the performance. Rather than throw away the old hard drive, I bought an enclosure for it to turn it into an external hard drive, and, since all the data was migrated to my new drive, I decided to install Ubuntu on it for funsies (note: I am a near-total Ubuntu n00b). My first attempt to install Ubuntu didn't work (it gave me errors about not being able to find the BIOS or something), but my second attempt finished successfully (can't remember what, if anything, I did different). However, when I plug the external drive into my Macbook, it gives me a message saying it can't read the disk. Moreover, when I go into the Startup Manager (i.e.: what you get when you turn on the Macbook while holding the option key), the external drive is not one of the available startup disks. I thought this might be because I have an older Macbook, so I tried booting it with my mom's Late 2011 Macbook, and got the same results. Then I tried booting it through my dad's Dell laptop that runs Windows 7, and that time it worked. This is really counter intuitive to me, since the hard drive originally came from a Macbook, so if anything you'd think it would be less compatible with the Windows laptop than the Macbook. In case it helps, here's a link to a picture of how I set up the partition table while doing the install (not shown there is the fact that I checked the "Format?" box next to the /boot partition, since it gave me a warning when I tried to continue the installation without doing so) Anyone have any clue at all? If it helps, the hard drive I'm using is a 120GB 5400-rpm Serial ATA hard disk drive.

    Read the article

  • How can I set external monitor as default?

    - by iJeeves
    I have connected an external monitor to my laptop through HDMI. Currently either my Desktop is getting extended to the external monitor (with native resolution) or low resolution on both when I choose "Same Image in both". How can I ensure that the external monitor is used by default and the laptop monitor just blanks. I generated the xorg.conf file by doing: X -configure The following is the content of xorg.conf.new file generated in my user folder. Should I copy this anywhere? Should I edit the contents? Section "ServerLayout" Identifier "X.org Configured" Screen 0 "Screen0" 0 0 InputDevice "Mouse0" "CorePointer" InputDevice "Keyboard0" "CoreKeyboard" EndSection Section "Files" ModulePath "/usr/lib/xorg/modules" FontPath "/usr/share/fonts/X11/misc" FontPath "/usr/share/fonts/X11/cyrillic" FontPath "/usr/share/fonts/X11/100dpi/:unscaled" FontPath "/usr/share/fonts/X11/75dpi/:unscaled" FontPath "/usr/share/fonts/X11/Type1" FontPath "/usr/share/fonts/X11/100dpi" FontPath "/usr/share/fonts/X11/75dpi" FontPath "/var/lib/defoma/x-ttcidfont-conf.d/dirs/TrueType" FontPath "built-ins" EndSection Section "Module" Load "glx" Load "dri2" Load "record" Load "extmod" Load "dbe" Load "dri" EndSection Section "InputDevice" Identifier "Keyboard0" Driver "kbd" EndSection Section "InputDevice" Identifier "Mouse0" Driver "mouse" Option "Protocol" "auto" Option "Device" "/dev/input/mice" Option "ZAxisMapping" "4 5 6 7" EndSection Section "Monitor" Identifier "Monitor0" VendorName "Monitor Vendor" ModelName "Monitor Model" EndSection Section "Device" ### Available Driver options are:- ### Values: : integer, : float, : "True"/"False", ### : "String", : " Hz/kHz/MHz", ### : "%" ### [arg]: arg optional #Option "NoAccel" # [] #Option "SWcursor" # [] #Option "ColorKey" # #Option "CacheLines" # #Option "Dac6Bit" # [] #Option "DRI" # [] #Option "NoDDC" # [] #Option "ShowCache" # [] #Option "XvMCSurfaces" # #Option "PageFlip" # [] Identifier "Card0" Driver "intel" BusID "PCI:0:2:0" EndSection Section "Screen" Identifier "Screen0" Device "Card0" Monitor "Monitor0" SubSection "Display" Viewport 0 0 Depth 1 EndSubSection SubSection "Display" Viewport 0 0 Depth 4 EndSubSection SubSection "Display" Viewport 0 0 Depth 8 EndSubSection SubSection "Display" Viewport 0 0 Depth 15 EndSubSection SubSection "Display" Viewport 0 0 Depth 16 EndSubSection SubSection "Display" Viewport 0 0 Depth 24 EndSubSection EndSection

    Read the article

  • Boot problems w/ External HDD

    - by JeremyT
    I'm having a problem with booting a live image off of a USB Hard Drive. I used Startup Disk Creator to make an Ubuntu 11.10 live image on a partition on my external so that I can use it on various computers. I set it up with ~4GB of persistent data So far I've tried it on two computers. One, a Dell, will boot to my external but it loads the select boot device very slowly. It hangs on a screen with an underscore for up to 5 minutes until it allows me to select which drive I want to boot from. After that, it works great. However, on my primary computer it doesn't work at all. It's an Acer from 2009 and it won't even recognize the drive. I don't see it anywhere in BIOS or the select boot disk list. The light on the external will come on at boot just fine so I know it's powering it at this time. Both computers worked perfectly with my 4GB flash drive that I had partitioned half and half (1st half FAT32 and second Ubuntu 11.10 live)

    Read the article

  • Dell M4600 with nVidia Quadro 2000M hangs on boot when external monitor is connected

    - by vladeta
    I have a problem with my fresh installed Ubuntu 12.04 LTS on my Dell M4600: nVidia quadro 2000M i7-2860 16GB ram 128GB SSD Dell/Samsung 750GB HDD IPS RGB laptop display When it is connected via DP++ to the external Dell U2311H monitor, it hangs on boot or when wakening from suspend. If I detach the DP cable it boots normally. I have tried all combinations that I have found, as adding to grub: "no splash", "boot=pci", "acpi=off", etc... I have also changed in nVidia X settings that external monitor is the primary one and also tried to delete monitor.xml file. There is no change it hangs each time after grub. It starts to load daemons then both screens are blank and then completely hangs with beep sound. What I discovered is if I detach the cable and wait for about 2 sec after grub starts booting and then physically connect DP cable while the Ubuntu is still booting everything works normally and I have a picture on my external screen while the laptop screen is off, just as I wanted. Do you maybe know how to solve this issue? Thank You.

    Read the article

  • Restoring backup with Deja Dup from external HD

    - by widgg
    So, here's the problem that I have with restoring. First, I backed up like everything. So I had place on the external HD for only one copy. I had to reinstall everything, but I didn't worry because I had a backup. But now, restoring doesn't work and it starts to be annoying. So, I right click "Restore missing files...". Then I have the popup window from Deja Dup asking where is the backup. So, I select the external HD and either put nothing in "folder" or just put ".". Thinking that it should be the base to look for backups. In both cases, after a while scanning, I get: The Volume "Filesystem root" has only 139.7mb disk space remaining. But my partition "/home" has 799.6Gb free. Also, I just want to restore some files, I don't need all of them. On my external HD, there's a file called: duplicity-full.20120514T220834Z.manifest. A text file. In it, I can see that everything is partitions in files of 52mb. So, small files are in one archive while very large files are split in multiple one. But I can see the exact list of file that I have. So, I'm guessing that my backup is intact. What am I doing wrong ? Is possible that it failes, even to list all the files, because I don't have enough space left on my ExtHD ? Why can't duplicity used another location to do that ?

    Read the article

  • ubuntu 12.04 LTS hangs on boot when external monitor is connected

    - by vladeta
    I have a problem with my fresh installed Ubuntu 12.04 LTS on my Dell M4600: nVidia quadro 2000M i7-2860 16GB ram 128GB SSD Dell/Samsung 750GB HDD IPS RGB laptop display When it is connected via DP++ to the external Dell U2311H monitor, it hangs on boot or when wakening from suspend. If I detach the DP cable it boots normally. I have tried all combinations that I have found, as adding to grub: "no splash", "boot=pci", "acpi=off", etc... I have also changed in nVidia X settings that external monitor is the primary one and also tried to delete monitor.xml file. There is no change it hangs each time after grub. It starts to load daemons then both screens are blank and then completely hangs with beep sound. What I discovered is if I detach the cable and wait for about 2 sec after grub starts booting and then physically connect DP cable while the Ubuntu is still booting everything works normally and I have a picture on my external screen while the laptop screen is off, just as I wanted. Do you maybe know how to solve this issue? Thank You.

    Read the article

  • External SWF to External SWF Timeline Communication, Flash, AS2

    - by jecca411
    Flash CS4, AS2 I have made an interactive tour. It can be seen here: http://www.92YTribeca.org/Tour click on the bottom image Each of the 4 sections are external swf and loaded on level 1. I want a button on one swf (floorplan) to load another swf (facility rentals) AND pinpoint a specific frame on the swf's timeline. I have tried many different ways, all end up loading the swf at the first frame and ignore the rest of the code talking about the timeline. I know I could split this swf up into more external swfs and get the result I want, but I would rather use code if I can. Is what I want to do possible? If so, how do I write the code? Thanks!

    Read the article

  • The Differences between MAC Address and Network Layer Address

    A Mac address is a fixed number associated with a NICs onboard memory. It is initially assigned at the factory. The MAC address is broken up into 2 parts. The first part is the Block id which is six digit sequences that is unique to each vender. The second section is the device id which is created and assigned by the manufacture. A Network layer address is different because there format based on the type of protocol and network used. Also, there unique id is based on a hierarchal addressing theme on subsets of data  and narrowing it down. Just like in an address you can narrow down your house, for example: Florida, Boca Raton, 33428, SW 53th street states that you live in Florida. You also live in the area located in Florida called Boca Raton and you are also in the area of 33428 which is located in Boca Raton. Finally you live on SW 8th street which is in the area of 33428 which is located in Boca Raton which is also located in Florida.

    Read the article

  • General Address Parser for Freeform Text

    - by Daemonic
    We have a program that displays map data (think Google Maps, but with much more interactivity and custom layers for our clients). We allow navigation via a set of combo boxes that prefill certain fields with a bunch of data (ie: Country: Canada, the Province field is filled in. Select Ontario, and a list of Counties/Regions is filled in. Select a county/region, and a city is filled in, etc...). While this guarantees accurate addresses, it's a pain for the users if they don't know where a street address or a city are located (ie, which county/region is kitchener in?). So we are looking at trying to do an address parser with a freeform text field. The user could enter something like this (similar to Google Maps, Bing Maps, etc...): 22 Main St, Kitchener, On And we could compartmentalize it into sections and do lookups on the data and get to the point they are looking for (or suggest alternatives). The problem with this is that how do we properly compartmentalize information? How do we break up the sections and find possible matches? I'm guessing we wouldn't be guaranteed that the user would enter data in a format we always expected (obviously). A follow up to this would be how to present the data if we don't find an exact match (or find multiple exact matches... two cities with the same street name in different counties, for example). We have a ton of data available in the mapping data (mapinfo tab format mostly). So we can do quick scans of street names, cities, states, etc. But I'm not sure about the best way to go about approaching this problem. Sure, using Google Maps would be nice, bue most of our clients are in closed in networks where outside access is not usually allowed and most aren't willing to rely on google maps (since it doesn't contain as much information as they need, such as custom map layers). They could, obviously, go to google and get the proper location then move to our software, but this would time consuming and speed of the process can be quite important.

    Read the article

  • Mail.app doesn't detect sender in Address Book

    - by CoreSandello
    Hi there. I don't understand, how does 'smart addresses' in Mail.app work. Recently I mentioned, that for some emails I don't see person's full name in 'From' column. I started to dig into this behavior and found out, that I have few contacts in my Address Book, that are not recognized by Mail.app. Here how it looks: I have a person in Address Book with filled email entry and filled first/last name (localized). I have an incoming email from that person (from email specified in Address Book), but first/last name in the email itself doesn't match with ones specified in Address Book (e. g. 'From' field in email looks like 'John [work] <[email protected]>' while Address Book entry is 'John Smith' (localized, in Russian)). And Mail.app doesn't recognize that this mail is originating from that person in Address Book: if I click on 'From' field, it suggests to me to add sender to Address Book, while for others' emails I have 'Show in Address Book' menu entry (especially for ones with full localized name in 'From' field). I'm wondering, is that behavior correct or I'm missing something? I'm using Snow Leopard & Mail 4.0; my system language set to English, if that matters. I'd like to have some clarifications on that Mail.app behavior: whenever it fixable or not (and if it's fixable, I'd like to see a fix). By the way, is it possible to match sender's address against Address Book entry in filter rules or not? That would be great, if I can create rules like 'move all mail from that person to that folder' without specifying exact source address. Thanks, Ivan.

    Read the article

  • Mail.app doesn't detect sender in Address Book

    - by CoreSandello
    I don't understand, how does 'smart addresses' in Mail.app work. Recently I mentioned, that for some emails I don't see person's full name in 'From' column. I started to dig into this behavior and found out, that I have few contacts in my Address Book, that are not recognized by Mail.app. Here how it looks: I have a person in Address Book with filled email entry and filled first/last name (localized). I have an incoming email from that person (from email specified in Address Book), but first/last name in the email itself doesn't match with ones specified in Address Book (e. g. 'From' field in email looks like 'John [work] <[email protected]>' while Address Book entry is 'John Smith' (localized, in Russian)). And Mail.app doesn't recognize that this mail is originating from that person in Address Book: if I click on 'From' field, it suggests to me to add sender to Address Book, while for others' emails I have 'Show in Address Book' menu entry (especially for ones with full localized name in 'From' field). I'm wondering, is that behavior correct or I'm missing something? I'm using Snow Leopard & Mail 4.0; my system language set to English, if that matters. I'd like to have some clarifications on that Mail.app behavior: whenever it fixable or not (and if it's fixable, I'd like to see a fix). By the way, is it possible to match sender's address against Address Book entry in filter rules or not? That would be great, if I can create rules like 'move all mail from that person to that folder' without specifying exact source address. Thanks, Ivan.

    Read the article

  • Performance cost of running Ubuntu from external hard drive

    - by dandan78
    A friend just complained to me about Ubuntu being slow. Although I've noticed a certain lack of snappiness with Linux vs Windows in the past, I really can't say I've had much to grumble about with the recent distributions of Ubuntu. That said, his objections seem much worse than the ones I used to have and I know that his current setup is significantly more powerful than my laptop. And then it turned out he is running Ubuntu off an external HDD hooked up via USB2.0. The HD enclosure is USB3.0 but apparently he can't manage to get it to boot on USB3.0 so he switched to one of the USB2.0 ports or whatever and that works, albeit not very well. Now I would expect USB to add some overhead to communication between the computer and the HDD; SATA is after all designed to get the maximum out of a hard drive, whereas USB is, well, universal. What are your expreriences with booting off external HDDs? Edit: Does anybody know just how much of a slowdown can be expected?

    Read the article

  • Video stutter when using external drive

    - by psion
    When using boxee to play video files off of an external western digital 1TB drive formatted NTFS, I notice a slight stutter in the video every 5-10 seconds. When using mplayer, it doesn't stutter as often, but it still stutters occasionally. If I play the video off of the local sata drive, it plays fine even in boxee. I use this computer as my HTPC and I just switched from windows to linux on it. In windows, I never had any sort of stutter playing movies from the drive. I am using the latest intel graphics drivers (for the intel GMA 950) root@eee-htpc:/home/htpc# grep wd /etc/mtab /dev/sdb1 /mnt/wd2 fuseblk rw,nosuid,nodev,allow_other,blksize=512 0 0 I notice that despite trying to use ntfs or ntfs-3g, ubuntu uses ntfs-fuse which I've heard is slower. /dev/sdb1: Timing buffered disk reads: 80 MB in 3.07 seconds = 26.08 MB/sec root@eee-htpc:/mnt/wd2# dd if=/dev/zero of=./120mb bs=1024 count=120000 root@eee-htpc:/mnt/wd2# time mv ./120mb /home/htpc real 0m2.095s user 0m0.016s sys 0m0.736s Even though fuse has a reputation for being slow, it should easily be fast enough for playing standard definition video files. So why the video stutter? edit: The issue seems to be overhead cpu usage from either playing off of a usb device or ntfs/fuse. Watching CPU usage with top, local files use 10-40% CPU. Watching the same video on the external formatted ntfs, it spikes to 170% (over 100% because of hyperthreading). To me it seems like it must be overhead from the fuse driver, though I don't know if it has more or less overhead than ntfs-3g. It's a EEEBox B202 that has an atom 270, so not exactly the most powerful out there. edit2: I believe the solution would be to use non-fuse drivers or different fuse drivers. so far I have not been able to. edit3: I've probably edited this more times than I should, but as an update I have upgraded ntfs drivers to ntfs-3g 2010.8.8 external FUSE 28 - Third Generation NTFS Driver using the following PPA - ppa:x3lectric/team-iquik-releases. When first opening a video file in boxee that's on ntfs there's still the same amount of lag. After a few minutes of video, the lag seems to go away and the cpu usage comes down to 10-40%. Every so often though, it begins to stutter again. Also, if I skip ahead/back in the file, it begins to stutter a lot.

    Read the article

< Previous Page | 1 2 3 4 5 6 7 8 9 10 11 12  | Next Page >