Search Results

Search found 13401 results on 537 pages for 'external monitor'.

Page 2/537 | < Previous Page | 1 2 3 4 5 6 7 8 9 10 11 12  | Next Page >

• My external monitor flickers when using with Vista, but not with XP/Linux

  - by satish

  I bought a new Dell Monitor ST 2410 model (24 inch). It works great when I connect my XP laptop to it or my Linux box. But when I connect it to my HP Laptop (Dv 6000 series) which has Vista on it. The monitor flickers a lot. Tried out all modes/frequencies but didn't help me. Any ideas?

  Read the article

• Amazing Secret Monitor (How-To Trick)

  - by Akemi Iwaya

  If you have an extra monitor sitting around and love the idea of making it a bit more unique, then this monitor hack may be the perfect ‘trick’ to use for your next DIY project. Here is extra footage compiled during the making of the video above that you can enjoy watching. Amazing Secret Monitor! (How To) [YouTube] Amazing Secret Monitor – (Extra Footage) [YouTube]     

  Read the article

• Keeping monitor Dell desk monitor 'connected' to dell studio 15 laptop?

  - by Jerry

  First of all, I am new to Ubuntu 10.04 but it is love at first sight and the only windows I will see again are in my house and car! Each time I disconnect my Dell Studio 15 from my Dell 36" monitor, I have to reconnect through the System/Monitor protocol. Question: Is there a way to set it up so once I slide my laptop under the stand, reconnect monitor cable, 3 usb's and press start that the Monitor screen will go 'live' without having to start all over?

  Read the article

• WM_NCHITTEST and secondary monitor to left of primary monitor

  - by AlanKley

  The described setup with 2nd monitor to left of primary causes WM_NCHITTEST to send negative values which is apparently not supported according to this post. I have a custom control written in win32 that is like a Group control. It has a small clickable area. No MOUSE events are coming to my control when the window containing the custom control lies on a second monitor to the left of the primary monitor. SPY++ shows WM_NCHITTEST messages but no Mouse messages. When window is moved to primary monitor or secondary monitor is positioned to right of primary (all points are positive) then everything works fine. Below is how the WM_NCHITTEST is handled in my custom control. In general I need it to return HTTRANSPARENT so as not to obscure other controls placed inside of it. Anybody have any suggestions what funky coordinate translation I need to do and what to return in response to WM_NCHITTEST to get Mouse messages translated and sent to my control in the case where it is on a 2nd monitor placed to the left of the primary monitor? case WM_NCHITTEST: { POINT Pt = {LOWORD(lP), HIWORD(lP)}; int i; ScreenToClient (hWnd, &Pt); if (PtInRect (&rClickableArea, Pt)) { return(DefWindowProc( hWnd, Msg, wP, lP )); } } lReturn = HTTRANSPARENT; break;

  Read the article

• Laptop screen blank after login when external monitor is not connected

  - by Ramon Suarez

  Ubuntu does not switch back automatically to only monitor present when booting after disconnecting external monitor. Here's a video showing what happens. I get to the login window and everything looks ok, then I type my password, the desktop image shows up and... everything goes blank. It does not happen when I just login as a guest. When possible I work with my laptop connected to an external screen via the VGA port. The problem comes when I boot the computer without that secondary screen connected: The login screen comes out ok. After login the screen goes black, but I can hear the login sound. If I hit ctr + alt + backwards-delete and login again sometimes it is fixed, but not all. If I log in as a different user everything is OK. Then I log in as my user and sometimes it works. To have a screen I have to plug a monitor. Although I have turned on the laptop display with that monitor on, if I reboot it goes blank again after login, even if I turn off the external monitor before turning off the computer. I've managed to get my screen back with my username after going into recovery mode, but only sometimes. Failsafe would not load after second screen asking me what I wanted to do (no mouse to click nor keyboard working). My computer is a LDLC Aurore BB1-i5 -8 -S1. Which is the configuration file that keeps the information about the monitors using Displays under lightgdm and where is it? I guess if I could edit it I may have a chance :) One of the things I tried following a solution in another post was removing my monitors.xml file, but it does not work and I don't know how to create a good one that I could use now. When doing DISPLAY=:0 xrandrI get: Screen 0: minimum 320 x 200, current 320 x 200, maximum 8192 x 8192 LVDS1 connected (normal left inverted right x axis y axis) 1366x768 60.0 + 1360x768 59.8 60.0 1024x768 60.0 800x600 60.3 56.2 640x480 59.9 VGA1 disconnected (normal left inverted right x axis y axis) HDMI1 disconnected (normal left inverted right x axis y axis) DP1 disconnected (normal left inverted right x axis y axis) This is the full dmesg after activating sudo xdiagnoseas Bryce sugested. (If you tell me the relevant parts I will paste them here) When conecting the external monitor, only the external will work, although I can see using Displays that the computer thinks that both are working. I've asked the question in Launchpad but have it keeps on expiring without any feedback. In my opinion Ubuntu should be able to detect automatically that there is no external monitor present and switch to the laptop monitor. There's a similar question here, but it does not apply to my case External monitor set as primary even when disconnected from laptop Update: For clarification, the problem happens only with my user and once I log in. I even get to see the screensaver for about a second, and then it goes blank. Tried Bryce's example (see his answer below), but it did not work. This is the info I get from tty1 with Display=:0 xrandr: – Ramon Suarez Jul 9 at 16:36 Screen 0: minimum 320 x 200, current 320 x 200, maximum 8192 x 8192 LVDS1 connected (normal left inverted right x axis y axis) 1366x768 60.0 + 1360x768 59.8 60.0 1024x768 60.0 800x600 60.3 56.2 640x480 59.9 VGA1 disconnected (normal left inverted right x axis y axis) HDMI1 disconnected (normal left inverted right x axis y axis) DP1 disconnected (normal left inverted right x axis y axis)

  Read the article

• Dell Dell E2009W monitor not detected

  - by Charles

  I have an issue with my monitor. I just installed Ubuntu 11.10, but the monitor that is plugged in doesn't appear anywhere. And by doesn't appear, I mean that in the "Displays" menu, it doesn't even appear as "Unknown", I just have my screen that appears and nothing else. It is connected through VGA, and the monitor is recognized with no problem on Windows 7. It is a Dell monitor. I'm not a pro with Ubuntu, so any help to diagnose the issue would be really helpful (and help me learn how to fix this kind of monitor issue in the future) Thanks !

  Read the article

• External monitor with NO mouse cursor

  - by Csaba Nyerges

  I am using a Fujitsu Siemens Amilo L7310 laptop computer with an external monitor. I'm wishihg to use version 10.04. The problem is, when I plug my laptop into the external monitor with my laptop screen turned either on or off, I do not see the mouse cursor on the external monitor! The mouse cursor is still there, although invisible. If I connect the external monitor to my laptop before swithing both on, the same happens. Is there any solution to make the cursor appear on the monitor?

  Read the article

• Dell monitor not detected (Ubuntu 11.10)

  - by Charles

  I have an issue with my monitor. I just installed Ubuntu 11.10, but the monitor that is plugged in doesn't appear anywhere. And by doesn't appear, I mean that in the "Displays" menu, it doesn't even appear as "Unknown", I just have my screen that appears and nothing else. It is connected through VGA, and the monitor is recognized with no problem on Windows 7. It is a Dell monitor. I'm not a pro with Ubuntu, so any help to diagnose the issue would be really helpful (and help me learn how to fix this kind of monitor issue in the future) Thanks !

  Read the article

• Dual monitor with different resolutions problem

  - by Mackemint

  I'm on an LG R405 with a PM965 chipset and a NVIDIA GeForce Go 8400M GS gaphics card. I'm trying to use an external monitor (Benq senseye3 G2222HDL) through a VGA out port. All was fine when installing except for the screen layouts were flip-flopped (computer defalut setup so external monitor was to the right instead of left). When I moved the secondary monitor to its real position in the setup, I started getting strange problems. I loose representation of large portions of the screen, on both screens, and have to reboot. If I plug the monitor in after rebooting I get more problems than when booting up with the monitor already plugged in, but in both cases I can barely see what I'm doing. Please advice! Regards /M

  Read the article

• Monitor resolution messed up, monitor is unknown.

  - by Kaustubh P

  Is there anyway to reset my monitor? My moitor is using the xorg.conf file. I use 10.04, without any Graphics Card. My monitor is an Acer X193W, with a native resolution of 1440x900. This is my xorg.conf file: Section "Screen" Identifier "Configured Screen Device" Device "Configured Video Device" Monitor "Test" DefaultDepth 16 SubSection "Display" Depth 16 Modes "1440x900_60.00" EndSubSection EndSection #Section "Device" # Identifier "Configured Video Device" # HorizSync # VertRefresh #EndSection I still cant view the native resolution, even when defined in the xorg file. An way I can revert to the default, or delete some files, to make the system detect the monitor again? My last resort is the cvt method, and adding it to the xrandr file. EDIT: I use Intel Drivers. My /proc/fb contains 0 VGA16 VGA

  Read the article

• Dual monitor Unity launcher opening on wrong monitor in 11.10

  - by user26381

  I just upgraded to Oneiric and now the Unity Dash launcher is on my left screen. I really want it on my right screen. But how do I do that? Why do I want the Dash on my right screen? My left screen is a smaller older monitor that I use to read/watch documentation or keep my music player open. I work on my right screen, that is bigger and is a better monitor. I have an Nvidia card and in the nvidia settings it is setup that the right monitor is my primary monitor, but Oneiric doesn't follow this setting anymore. I thought this was a bug, but is seems to be intended behavior... https://bugs.launchpad.net/ubuntu/+source/unity/+bug/742544 Some poster in this thread explains that he "patched it locally", but I have no idea how to do this. Does somebody know how to do this? Or maybe there is another solution?

  Read the article

• Unable to boot ubuntu 11.10 from external usb drive

  - by user45006

  I'm new to Ubuntu (and actually all things Linux) as of this morning, so please excuse any stupid mistakes I may be making. I recently bought an external hard drive for my newly built PC (that is running windows 7 if it matters). I would like to install Ubuntu onto the external drive and boot from there. I downloaded Ubuntu 11.10 and made a bootable cd, unplugged my internal HDDs, plugged in the external drive, installed Ubuntu 11.10 on the external drive via the installer, and replugged in my internal HDDs. Then I set my bios boot order to: Boot from USB-HDD - Boot from Hard Disk - Boot from CD/DVD. Now when I restart I get the message "Starting Operating System..." (or something like that, I forget exactly what it says) that lingers on the screen for a moment and then windows starts. Any idea what the problem may be? ~Relevant info~ BIOS version: Award Software International, Inc. F2, 2/22/2011 Ubuntu Version: 11.10 External Hard Drive: Western Digital My Passport Essential 500GB Portable Hard Drive (Black) ~Things I've already tried~ 1) Unplug internal HDDs so that only external drive was plugged in via usb. Same thing happened only obviously my BIOS could not detect any hard drives besides the external one. When booting received error "Could not detect operating system" 2) Formatted external hard drive and re installed. It didn't make a difference, however interestingly when I booted from cd the ubuntu installer said it detected ubuntu 11.10 on the external hard drive. 3) Within BIOS I've messed around with every boot order combo I could think of both in the "Hard Disk boot order" screen and the "Boot order" screen. I'm a little confused of why there are two screens for this. 4) Held F12 during startup which opens (what I think is) the one time boot screen and it gave me the options "Hard Drive", "cd/dvd", "USB-FDD", "USB-cdrom", "USB-HDD", and "USB-something else I can't remember what it was". I tried all of them, but the same thing as before happened each time. ~References~ I noticed several people on askubuntu have tried to do something similar if not the exact same. In fact, I even found a post that pretty much outlines step by step exactly what I did... only their's worked. /jealous. Linky: Install Ubuntu or Kubuntu on a External USB Drive I'm willing to try a different version of ubuntu - it's not like my heart is set on 11.10, but it's a pain to open my case and unplug my internal hard drives so I'd prefer not to do this unless someone is reasonably confident it'll work. Thank you for all of your help in advance! I'm really looking forward to exploring Ubuntu!

  Read the article

• Dual monitor not working completely in 12.10 after upgrade

  - by Mark Baldridge

  At 12.04, dual monitors worked perfectly. After upgrading to 12.10, the primary monitor works, the second monitor only partly works. I am sure there is some difference between the releases that I have missed setting properly. System settings - Displays show both correctly as Acer 22" monitors at 1680x1050 (16:10). An icon on monitor 2 is present, but elongated; almost an artifact, since other icons on the primary screen are absent, but this one icon is there on th second monitor. Selecting the icons on both screens exist. Painting is weird on monitor 2. Launcher exists and works on both screens, but even with sticky edges off, the cursor stops at the left edge of monitor 2. Clicking on text editor on screen 2 launcer will launch gedit there. If I drag it, it leaves a trail of after images like repaint is failing. If I drive the cursor on the launcher, the help tags like "LibreOffice Writer" appear, but stay on screen unless I drag the active gedit window over them. Then part of the help bubbles are overwritten, leaving behind after images of the gedit window on screen. What is really fascinating is that the System settings - Displays is now ignoring monitor selection, after allowing it earlier. Just before this, the help popup which said "Select a monitor to change its properties; drag to rearrange its placement" actually let me do that. Maybe a trick of where I grab the edge of the monitor in the Displays setting. I just found a working handle. When I drag monitor 1 to the right of monitor 2, "Apply" and confirm, both monitors work normally (although the right monitor lets the cursor slide off the right edge onto the left edge of monitor 1 - which sounds correct). Painting of windows does not leave an after image. However, success is only temporary. The setting survives the reboot, but painting on the left monitor, now monitor 2, now replicates the issues from before. The after image of the gedit window and the small window for "Are you sure you want to close all programs and restart the computer?" are still on monitor 2 (on the left now), even though they are not real windows, nor do they have processes behind them. Curiously, in Displays, the "green" monitor on the left in the display window is matched by the right monitor color in the monitor upper left corner. Probably makes sense as the one on the right is now monitor 1. If I repeat the "drag the left monitor to the right of the right monitor on the "Displays" window, things are oriented properly, with no display artifacts as I drag windows around either screen. Also the description bubbles that pop up are overwritten on both screens, so none of those artifacts either. This goodness does not survive a reboot, however. Have not tried logging out and back in. All of this after positing that the motherboard VGA and HDMI ports could have been the issue. So, I installed an e-GeForce 7600 GT Dual DVI (I know the web thinks it is not DVI, but VGA, but the connectors are DVI). No change to the weird behavior. The good parts continue to work, the weirdness also works, and swapping monitor positions seems to cure the issue. So, is there a setting I have missed? Given "swapping" monitor 1 and 2 on the System Settings... - Displays makes it work, just not across boot, I suspect so.

  Read the article

• Multi Monitor Setup Problems

  - by Shamballa

  I have Ubuntu 10.04 LTS - the Lucid Lynx. I have until recently been using a nVida Graphics card (NVIDIA GeForce 9800 GT) with two monitors attached, this all worked fine and dandy. A couple of days ago I bought two new identical LCD monitors for a multi monitor setup and two ATI graphics cards (ATI Sapphire Radeon HD5450). NOTE *All monitors work fine in Windows XP, 2k, Vista and 7 After I had booted into Ubuntu only one display came on, that I kind of expected anyway, then I removed the driver for the nVidia card and downloaded the ATI version which gave me the ATI Catalyst Control Center - in that only two of the displays were showing the third was disabled and showing unknown driver. I enabled the third monitor that stated "Unkown Driver" and had to reboot, upon reboot none of the displays work. I restarted and booted up into recovery mode and from now that is only what I can get into using a failsafe driver. It seems according to the log that a server is already active for Display 0 and I have to remove /tmp/.X0-lock and start again. This is what the log file is saying: Fatal Server Error Server is already active for display 0 if this server is no longer running, remove /tmp/.X0-lock and start again. (WW) xf86 closeconsole: KDSETMODE failed: Bad file descriptor (WW) xf86 closeconsole: VT_GETMODE failed: Bad file descriptor (WW) xf86 closeconsole: VT_GETSTATE failed: Bad file descriptor ddxSigGiveUp: closing log I have tried looking at my xorg.config file but unfortunately I have not really got a clue as to how it "should" be - I have tried regenerating it using this command from a terminal: sudo dpkg-reconfigure -phigh xserver-xorg but that had no effect so I am currently stuck in failsafe driver mode but two monitors are active but are mirroring each other. I hope that this is not to long - looking back I have been going on a bit! but I am just trying to explain as much as I can... I have asked this on Linuxquestions but nobody seems to know either or at least I have not had any responses. Could some kind soul please help explain what I can do from here? I would be eternally grateful. Chris * Update * Removing xorg.conf does nothing other than allowing me to use only two monitors - using the command: sudo aticonfig --initial generates the xorg.conf file below: but does not work either - I just get two monitors... Section "ServerLayout" Identifier "aticonfig Layout" Screen 0 "aticonfig-Screen[0]-0" 0 0 EndSection Section "Files" EndSection Section "Module" EndSection Section "Monitor" Identifier "aticonfig-Monitor[0]-0" Option "VendorName" "ATI Proprietary Driver" Option "ModelName" "Generic Autodetecting Monitor" Option "DPMS" "true" EndSection Section "Device" Identifier "aticonfig-Device[0]-0" Driver "fglrx" BusID "PCI:1:0:0" EndSection Section "Screen" Identifier "aticonfig-Screen[0]-0" Device "aticonfig-Device[0]-0" Monitor "aticonfig-Monitor[0]-0" DefaultDepth 24 SubSection "Display" Viewport 0 0 Depth 24 EndSubSection EndSection I have tried using this command from a thread on the Ubuntu Forums with a question similar to mine: sudo aticonfig --initial=dual-head --adapter=all Generated xorg.conf file Section "ServerLayout" Identifier "aticonfig Layout" Screen 0 "aticonfig-Screen[0]-0" 0 0 Screen "aticonfig-Screen[0]-1" RightOf "aticonfig-Screen[0]-0" Screen "aticonfig-Screen[1]-0" RightOf "aticonfig-Screen[0]-1" Screen "aticonfig-Screen[1]-1" RightOf "aticonfig-Screen[1]-0" EndSection Section "Files" EndSection Section "Module" EndSection Section "Monitor" Identifier "aticonfig-Monitor[0]-0" Option "VendorName" "ATI Proprietary Driver" Option "ModelName" "Generic Autodetecting Monitor" Option "DPMS" "true" EndSection Section "Monitor" Identifier "aticonfig-Monitor[0]-1" Option "VendorName" "ATI Proprietary Driver" Option "ModelName" "Generic Autodetecting Monitor" Option "DPMS" "true" EndSection Section "Monitor" Identifier "aticonfig-Monitor[1]-0" Option "VendorName" "ATI Proprietary Driver" Option "ModelName" "Generic Autodetecting Monitor" Option "DPMS" "true" EndSection Section "Monitor" Identifier "aticonfig-Monitor[1]-1" Option "VendorName" "ATI Proprietary Driver" Option "ModelName" "Generic Autodetecting Monitor" Option "DPMS" "true" EndSection Section "Device" Identifier "aticonfig-Device[0]-0" Driver "fglrx" BusID "PCI:1:0:0" EndSection Section "Device" Identifier "aticonfig-Device[0]-1" Driver "fglrx" BusID "PCI:1:0:0" Screen 1 EndSection Section "Device" Identifier "aticonfig-Device[1]-0" Driver "fglrx" BusID "PCI:2:0:0" EndSection Section "Device" Identifier "aticonfig-Device[1]-1" Driver "fglrx" BusID "PCI:2:0:0" Screen 1 EndSection Section "Screen" Identifier "aticonfig-Screen[0]-0" Device "aticonfig-Device[0]-0" Monitor "aticonfig-Monitor[0]-0" DefaultDepth 24 SubSection "Display" Viewport 0 0 Depth 24 EndSubSection EndSection Section "Screen" Identifier "aticonfig-Screen[0]-1" Device "aticonfig-Device[0]-1" Monitor "aticonfig-Monitor[0]-1" DefaultDepth 24 SubSection "Display" Viewport 0 0 Depth 24 EndSubSection EndSection Section "Screen" Identifier "aticonfig-Screen[1]-0" Device "aticonfig-Device[1]-0" Monitor "aticonfig-Monitor[1]-0" DefaultDepth 24 SubSection "Display" Viewport 0 0 Depth 24 EndSubSection EndSection Section "Screen" Identifier "aticonfig-Screen[1]-1" Device "aticonfig-Device[1]-1" Monitor "aticonfig-Monitor[1]-1" DefaultDepth 24 SubSection "Display" Viewport 0 0 Depth 24 EndSubSection EndSection This upon reboot renders ALL monitors blank and I have to go into recovery mode and use a failsafe driver. This is so much harder than I thought it would be, I don't think Ubuntu likes ATI for multi (3) monitors or maybe the other way around. Can anyone help still?

  Read the article

• Could not apply the stored configuration for the monitor

  - by dellphi

  I'm using Nvidia 7300 gt and monitor-Acer V173w, on 64 bit Ubuntu 10.04. Compiz and Emerald went well, but at the time of entry into the GUI, I always receive the message : "Could not apply the stored configuration for the monitor, could not find a suitable configuration of screens" Why do I always receive it, and what is wrong with the monitor configuration or pci-e is used? root@dellph1-desktop:/# xrandr Screen 0: minimum 320 x 240, current 1440 x 900, maximum 1440 x 900 default connected 1440x900+0+0 0mm x 0mm 1440x900 50.0* 1024x768 51.0 58.0 59.0 1360x768 52.0 53.0 1152x864 54.0 55.0 56.0 57.0 960x600 60.0 960x540 61.0 896x672 62.0 840x525 63.0 64.0 65.0 66.0 832x624 67.0 800x600 68.0 69.0 70.0 71.0 72.0 73.0 800x512 74.0 720x450 75.0 680x384 76.0 77.0 640x512 78.0 79.0 640x480 80.0 81.0 82.0 83.0 576x432 84.0 85.0 86.0 87.0 512x384 88.0 89.0 90.0 416x312 91.0 400x300 92.0 93.0 94.0 95.0 320x240 96.0 97.0 98.0 root@dellph1-desktop:/# === xorg.conf # nvidia-settings: X configuration file generated by nvidia-settings # nvidia-settings: version 260.19.29 ([email protected]) Wed Dec 8 12:27:27 PST 2010 Section "ServerLayout" Identifier "Layout0" Screen 0 "Screen0" 0 0 InputDevice "Keyboard0" "CoreKeyboard" InputDevice "Mouse0" "CorePointer" Option "Xinerama" "0" EndSection Section "Files" EndSection Section "InputDevice" # generated from default Identifier "Mouse0" Driver "mouse" Option "Protocol" "auto" Option "Device" "/dev/psaux" Option "Emulate3Buttons" "no" Option "ZAxisMapping" "4 5" EndSection Section "InputDevice" # generated from default Identifier "Keyboard0" Driver "kbd" EndSection Section "Monitor" # HorizSync source: xconfig, VertRefresh source: xconfig Identifier "Monitor0" VendorName "Unknown" ModelName "Acer V173W" HorizSync 30.0 - 83.0 VertRefresh 55.0 - 75.0 Option "DPMS" EndSection Section "Device" Identifier "Device0" Driver "nvidia" VendorName "NVIDIA Corporation" BoardName "GeForce 7300 GT" EndSection Section "Screen" # Removed Option "metamodes" " 1440x900_60 +0+0; 1280x1024 +0+0" # Removed Option "metamodes" "1440x900 +0+0" Identifier "Screen0" Device "Device0" Monitor "Monitor0" DefaultDepth 24 Option "TwinView" "0" Option "TwinViewXineramaInfoOrder" "CRT-0" Option "metamodes" "1440x900_75 +0+0; 1440x900 +0+0" SubSection "Display" Depth 24 EndSubSection EndSection

  Read the article

• Advanced System Monitor/Task Manager?

  - by instanceofTom

  When using kubuntu I noticed that the standard task manager/system monitor was a bit more capable than gnome-system-monitor, is there a more advanced system/task monitor for ubuntu that is based on gnome opposed to KDE? Specifically the features from the Kubuntu task manager that I am looking for are the ability to control the I/O priority of individual processes (not just their nice), and the ability to control the I/O scheduling algorithm ( round-robin, FIFO, etc). What are my options?

  Read the article

• Find out monitor make / model

  - by thefragileomen

  My friend has recently bought a second-hand vehicle with an in-car computer and it's wired up to a touchscreen monitor on the dashboard (very impressive!). Now, I've helped him install Ubuntu on it today but we can't establish the make and model of the connected touchscreen monitor to try and source the drivers to make the touchscreen function work. Are there any Linux commands to work out the make / model of an attached monitor? I've tried Google which pointed me towards the /etc/X11 directory but have had no joy with that.

  Read the article

• How to create/extract the EDID for/from a Monitor

  - by Luis Alvarado

  Is it possible to create or extract the Extended Display Identification Data (EDID) for/from a monitor. I have some issues with my monitor with the VGA and HDMI cables and I would like to test if by adding the EDID to the Nvidia Settings it could help in solve this issues. With the VGA cable I get a black out error and with the HDMI I get some EDID errors (bad EDID). So how can I create the EDID or extract it from the monitor by detecting its capabilities.

  Read the article

• monitor height differences & the mouse going off screen

  - by fastmultiplication

  In ubuntu 10.10 I have a dual monitor setup. I have an nVidia graphics card and am using twinview. One of the monitors is 1024 pixels high and the other is 900. In the monitor configuration screen & in real life, I have them set up side by side, 1024 on the left. The result of this is that when I am on the bottom of the left monitor and move the mouse to the right, it goes into the hidden area below the right monitor's visible area. It seems like it would make a lot more sense for it to be bumped up to the bottom of the right monitor - since one almost never wants to move the mouse into an area of the screen that doesn't show up. And, systems I have used before have been set up that way. How can I set this up? I am not interested in lists of window managers for ubuntu; I would like to know the identity of a particular WM or set of steps I can take to solves the particular problem I have outlined above. Thanks! EDIT: I changed to use two seperate X window monitors, and set them up relatively positioned so that just the corner touches and the mouse can cross there, so the difference in heights doesn't matter.

  Read the article

• Accidentally Changed Dual Monitor Setup and don't know how to reset it

  - by user203783

  I have a dual monitor setup with my laptop and an external Asus monitor running under Ubuntu 11.10. When I first started using Ubuntu, it synced both screens. What showed up on my laptop showed up on my eternal monitor. Last night, I accidentally knocked the HDMI cable from its port (not that unusual in the tight space I work in). When I plugged it back in, as usual, the external monitor only displayed my wallpaper. Usually, I just restart Ubuntu and it resets, but last night what I now realize was the display console came up and somehow I changed the setup. Now the two screens show different jobs so to speak. Also, the external monitor doesn't display the ribbon, making switching between Firefox tabs and windows or apps jarring. I write for a living and need to quickly check bits of research, notes or sources while writing and the extra switching between mouse pad and external mouse to get one or the other screen to respond interrupts my work flow. The only technical help I can offer is when the display console popped up, the graphical representation of the screens was that the external screen appeared layered over by about one-quarter of the laptop screen. Again, these were icons. I tried to replicate that after I obviously screwed things up. If someone could help. I would appreciate it. If I have to use terminal, that's fine. I started using computers for writing back when they were green DOS prompts. There's a certain elegance to prompt commands to me. Maybe it's the writer in me. Again, if anyone can help me return my screens to sync under Ubuntu 11.10, I would greatly appreciate it.

  Read the article

• External monitor problems with Asus UX32VD in 12.04

  - by rsilva

  I've posted this video where I show one of the problems I'm facing with my UX32VD in regard of external monitors. As you can see as soon as I plugged the external monitor the laptop screen goes black and the external monitor displays a single color (color changes between red, green and blue). However this does not always happen. For instance if I reboot the laptop with the external monitor already plugged in I get to use it but not the laptop screen. In the Displays settings the laptop screen it's not even listed. Other times it just works. The to screens, without any problems. I tried with other to different external monitor and all this apparently random issues repeat, I even tried using HDMI cable instead. Same random behavior. This question seams to cover one of this issues however the answer did not helped me. I was forced to use the 3.5.2 kernel in order to use the Intel graphics card else the Gallium something was used. Also I've Bumblebee installed.

  Read the article

• Setting up 2 external monitors on a laptop with VGA splitter

  - by mike

  I have a laptop with a graphics card that supports 2 displays. I would like to know the easiest way to set it up so I can close my laptop lid and use 2 external monitors (unique displays). I use it primarily for office applications and video and want a quality, clear picture. The laptop has 1 VGA port and I have 2 24" 1920x1200 monitors that have VGA and DVI ports. So a few questions: Can I just use a VGA splitter? (seen mixed feedback on this) Would it a VGA to 2 DVI splitter give a better picture quality? (if it exists) Would I be better upgrading laptop to one with 2 digital ports ( I just see a lot with VGA and HDMI though) specs: Model: Toshiba Satellite C675-S106 (Windows 7) Graphics Card: Intel HD Graphics 3000 (supports 2 displays) Processor: Intel Core i3-2350M

  Read the article

• Desktop Fun: Dual Monitor Wallpaper Collection Series 2

  - by Asian Angel

  Last month we brought you the first batch of wallpapers geared specifically towards dual monitor setups. Today we present the second offering in our series of dual monitor wallpaper collections. Note: Click on the picture to see the full-size image—these wallpapers vary in size so you may need to crop, stretch, or place them on a colored background in order to best match them to your screen’s resolution. More Dual Monitor Goodness Desktop Fun: Dual Monitor Wallpaper Collection Series 1 Span the same wallpaper across two monitors or use a different wallpaper for each. Dual Monitors: Use a Different Wallpaper on Each Desktop in Windows 7, Vista or XP For more wallpapers be certain to see our great collections in the Desktop Fun section. Latest Features How-To Geek ETC The 20 Best How-To Geek Linux Articles of 2010 The 50 Best How-To Geek Windows Articles of 2010 The 20 Best How-To Geek Explainer Topics for 2010 How to Disable Caps Lock Key in Windows 7 or Vista How to Use the Avira Rescue CD to Clean Your Infected PC The Complete List of iPad Tips, Tricks, and Tutorials Tune Pop Enhances Android Music Notifications Another Busy Night in Gotham City Wallpaper Classic Super Mario Brothers Theme for Chrome and Iron Experimental Firefox Builds Put Tabs on the Title Bar (Available for Download) Android Trojan Found in the Wild Chaos, Panic, and Disorder Wallpaper

  Read the article

• No signal on monitor after plug it to a linux box

  - by yaroot

  I use my old computer as an NAS, so I remove the monitor after I installed linux on it (disconnect vga cable). I use ssh to control the machine and it works fine. Until some day, after kernel/softare upgrade or messing up some configs, I cannot connect to it through ssh, then I have to plug the monitor back, but the monitor says "No input signal". So I have to restart the computer WITH the monitor connected, and the monitor's back! I think the computer/linux kernel doesn't detect the monitor plug-in event. So how can I start my linux box without a monitor, but when it goes wrong I can still plug my monitor (vga) back and use the console. Edit: just one pci-e video card, has dvi, vga, tv/out (s-video) Edit2: Xorg is not running. I just need the console (CTRL+ALT+F1). The problem is, if the machine booted without a monitor connected, it won't give me a pseudo terminal after I attach the vga cable while it's running. Clearly the monitor is not auto detected as usb device. I'm wondering how to let the monitor auto detected.

  Read the article

• Ubuntu not detecting second monitor

  - by Julian Le Saux

  I'm running Ubuntu 12.04 on a Lenovo x61s Thinkpad. As the screen's rather small and I want to do some video editing, I thought I'd plug in a monitor and use that. The monitor is Relisys JM777 (quite old). When I plug it into my other computer, which is running Windows 7, it immediately mirrors the display; but when plugged into the Lenovo the monitor screen remains blank. The graphics card on the Lenovo is a "VGA compatible controller" according to SysInfo. Anybody got any suggestions? I'm quite new to Linux, so simple explanations would be greatly appreciated. The contents of my Xorg.0.log file can be seen at http://paste.ubuntu.com/1009855/ .

  Read the article

< Previous Page | 1 2 3 4 5 6 7 8 9 10 11 12  | Next Page >