Search Results

Search found 415 results on 17 pages for 'fdisk'.

Page 2/17 | < Previous Page | 1 2 3 4 5 6 7 8 9 10 11 12  | Next Page >

• format/build raid 5 with one 4k drive, three 512b

  - by skidawgz

  I have 4 WD 1TB drives which I want to 4x1TB Raid5. I am not sure what course of action to take next. How do I configure my 4th drive (sde) to align with the rest? Will this affect performance? I rcv this msg (which brings me here to ask these question): The device presents a logical sector size that is smaller than the physical sector size. Aligning to a physical sector (or optimal I/O) size boundary is recommended, or performance may be impacted. fdisk -l shows: Disk /dev/sdb: 1000.2 GB, 1000204886016 bytes 81 heads, 63 sectors/track, 382818 cylinders, total 1953525168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0xf324ba09 Device Boot Start End Blocks Id System /dev/sdb1 2048 1953525167 976761560 fd Linux raid autodetect Disk /dev/sdc: 1000.2 GB, 1000204886016 bytes 81 heads, 63 sectors/track, 382818 cylinders, total 1953525168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x38bcc1f0 Device Boot Start End Blocks Id System /dev/sdc1 2048 1953525167 976761560 fd Linux raid autodetect Disk /dev/sdd: 1000.2 GB, 1000204886016 bytes 81 heads, 63 sectors/track, 382818 cylinders, total 1953525168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x570f77e7 Device Boot Start End Blocks Id System /dev/sdd1 2048 1953525167 976761560 fd Linux raid autodetect Disk /dev/sde: 1000.2 GB, 1000204886016 bytes 255 heads, 63 sectors/track, 121601 cylinders, total 1953525168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 4096 bytes I/O size (minimum/optimal): 4096 bytes / 4096 bytes Disk identifier: 0xeb665e7b Device Boot Start End Blocks Id System

  Read the article

• Some info about SD card patitions after the use of the dd statment and some oiters doubts?

  - by AndreaNobili

  I am not very experienced using Linux and I have the following situation that cause me some doubts. I have wrote RaspBian (the RaspBerry linux distribution) on an SD card using Ubuntu dd statment: sudo dd if=2014-01-07-wheezy-raspbian.img of=/dev/sdb bs=1024 So if now I perform the fdisk -l statment I obtain that I have 2 partitions related to my SD card, that are the followins: Dispositivo Boot Start End Blocks Id System /dev/sdb1 8192 122879 57344 c W95 FAT32 (LBA) /dev/sdb2 122880 5785599 2831360 83 Linux And now the first doubt: the dd statment create on the SD card two partitions: 1) /dev/sdb1 that is a litle FAT32 partition (what it means (LBA)?) 2) /dev/sdb2 that is a larger Linux ext3 partition Ok...the doubt is: why it also create to me a FAT32 partition and not only a Linux ext3 partition? Ok...if I go into my computer resource I can see a device (related to my SD card) into the devices list that contains some RaspBian file, following a screenshot: And if I see the property of this device I obtain this: So, looking at the previous screenshot it seems to me that this is the small FAT32 partition, and now I have the followings doubts: If it is the smallest FAT32 partition, what contains? The RaspBian boot or what? Why, in the devices list, I have only the FAT32 partition and not also the Linux one (/dev/sdb2), to see it have I to mount it? how? Tnx

  Read the article

• How to create NTFS partition in Linux to install Windows 7 from USB?

  - by Michal Stefanow

  I messed up with my computer and need help. Generally: install Windows 7 from USB. Problem: "setup was unable to create a new system partition" When first attempt to install Windows 7 failed I tried Linux live USB, installed distro to HDD, and erased all the existing partitions. Current state (fdisk -l): [writing from other computer so no copy and paste] /dev/sda1 305GB Linux /dev/sda2 7GB Extended /dev/sda5 7GB Linux Swam / Solaris To create a new, NTFS partition: fdisk /dev/sda n (for new) p (for primary) 3 (for partintion number) "No free sectors available" All the HDD was formatted couple of minutes before so there is a lot of free space but how to resize a parition? I cannot find an option for resizing in man fdisk. Some people say I should use gparted but my distro doesn't not contain this package. And my distro doesn't support wireless drivers so I have serious problems with downloading stuff. I tried also using cfdisk but any command results in: "cfdisk bad primary partition 1 partition ends in the final partial cylinder" I tried also removing partition 1 and then creating a new one (so there is no "no free sectors"). I'm receiving a warning: "Re-reading the partition table failed with error 16: Device or resource busy. The kernel still uses the old table. The new table will be used at the next reboot." After restating: "grub rescue, no known filesystem" It may indicate that some changes have been made BUT when running Windows 7 installed some another error: "Windows cannot be installed to Disk 0 Partition 1" More detailed: "Windows cannot be installed to this hard disk space. Windows must be installed to a partition formatted as NTFS." So formatting drive using Windows 7 installer BUT this time yet another error: "Setup was unable to create a new system partition or locate an existing system partition. See the setup log files for more information" Apparently I cannot access logs (how?) and I am back to drawing board with my live USB (this time showing partition as HPFS/NTFS). Any suggestions how to install Windows 7? Should I reinstall Linux to HDD, erase existing partitions once again, and use Parted rather than gparted (parted is included in the distro). Or maybe should I create another bootable USB such as PartedMagic to painlessly create partitions? I just want to install Windows 7 from USB, my laptop is semi-operational and I am ready to receive some help regarding fdisk and creating NTFS partitions. UPDATE: I did as suggested (removed all the partitions) and tried to install in unallocated space. Tried to create a new partition and format it. Same error: "setup was unable to create a new system partition" Came to the conclusion it may have something to do with TrueCrypt I have recently installed. Right now trying to FIX MBR (as I haven't got possibility to create rescue disc without optical drive)

  Read the article

• Start Anew with my USB stick

  - by Asaf

  This story starts with me taking my USB stick to work and unplugging it by accident in the middle of a file transfer. The USB stopped working completely, now I have Linux Ubuntu on my Laptop at home So I tried messing around with Gparted and Fdisk and all it did Was making my USB stick be partition less and 8 MB instead of 2GB So instead of creating more havoc, I ask kindly for help. I tried going to fdisk /dev/sdb and inside there were no partitions, added a new one but that didn't really do anything, /dev/sdb1 was none-existent..

  Read the article

• What is the difference between the Linux and Linux LVM partition type?

  - by ujjain

  Fdisk shows multiple partition types. What is the difference between choosing 83) Linux and 8e) Linux LVM? Choosing 83) Linux also works fine for using LVM, even creating a physical volume on /dev/sdb without a partition table works. Does picking a partition type in fdisk really matter? What is the difference in picking Linux or Linux LVM as partition type? [root@tst-01 ~]# fdisk /dev/sdb WARNING: DOS-compatible mode is deprecated. It's strongly recommended to switch off the mode (command 'c') and change display units to sectors (command 'u'). Command (m for help): l 0 Empty 24 NEC DOS 81 Minix / old Lin bf Solaris 1 FAT12 39 Plan 9 82 Linux swap / So c1 DRDOS/sec (FAT- 2 XENIX root 3c PartitionMagic 83 Linux c4 DRDOS/sec (FAT- 3 XENIX usr 40 Venix 80286 84 OS/2 hidden C: c6 DRDOS/sec (FAT- 4 FAT16 <32M 41 PPC PReP Boot 85 Linux extended c7 Syrinx 5 Extended 42 SFS 86 NTFS volume set da Non-FS data 6 FAT16 4d QNX4.x 87 NTFS volume set db CP/M / CTOS / . 7 HPFS/NTFS 4e QNX4.x 2nd part 88 Linux plaintext de Dell Utility 8 AIX 4f QNX4.x 3rd part 8e Linux LVM df BootIt 9 AIX bootable 50 OnTrack DM 93 Amoeba e1 DOS access a OS/2 Boot Manag 51 OnTrack DM6 Aux 94 Amoeba BBT e3 DOS R/O b W95 FAT32 52 CP/M 9f BSD/OS e4 SpeedStor c W95 FAT32 (LBA) 53 OnTrack DM6 Aux a0 IBM Thinkpad hi eb BeOS fs e W95 FAT16 (LBA) 54 OnTrackDM6 a5 FreeBSD ee GPT f W95 Ext'd (LBA) 55 EZ-Drive a6 OpenBSD ef EFI (FAT-12/16/ 10 OPUS 56 Golden Bow a7 NeXTSTEP f0 Linux/PA-RISC b 11 Hidden FAT12 5c Priam Edisk a8 Darwin UFS f1 SpeedStor 12 Compaq diagnost 61 SpeedStor a9 NetBSD f4 SpeedStor 14 Hidden FAT16 <3 63 GNU HURD or Sys ab Darwin boot f2 DOS secondary 16 Hidden FAT16 64 Novell Netware af HFS / HFS+ fb VMware VMFS 17 Hidden HPFS/NTF 65 Novell Netware b7 BSDI fs fc VMware VMKCORE 18 AST SmartSleep 70 DiskSecure Mult b8 BSDI swap fd Linux raid auto 1b Hidden W95 FAT3 75 PC/IX bb Boot Wizard hid fe LANstep 1c Hidden W95 FAT3 80 Old Minix be Solaris boot ff BBT 1e Hidden W95 FAT1 Command (m for help):

  Read the article

• cannot format a fat filesystem, getting error "Both FATs appear to be corrupt. Giving up."

  - by Nilesh

  i am trying format an FAT (or FAT32) file system on my ubuntu system, but i am not able to format the device, each time i am getting the error "Both FATs appear to be corrupt. Giving up." i have tried all options like sudo dosfsck -t -a -w /dev/sdc1 sudo dosfsck -w -r -l -a -v -t /dev/sdc1 but each time the same message comes, can any one guide me how to recover the filesystem, also i don't mind losing data of this drive as this is an external pen drive. Also, can u pl suggest of some method other then booting from a CD with software like GPARTED or something like that.

  Read the article

• which drive do I mount

  - by Crash893

  I have a system hdd then two raid1 hard drives I see that sda1 is the system drive but when i do a fdisk -l I get the following results so which of the following do i need to mount to get the "raid" drive and not the individual hdd? root@Mxxxx-PDC:/etc/samba# fdisk -l Disk /dev/sda: 251.0 GB, 251000193024 bytes 255 heads, 63 sectors/track, 30515 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Disk identifier: 0x000762dc Device Boot Start End Blocks Id System /dev/sda1 * 1 30328 243609628+ 83 Linux /dev/sda2 30329 30515 1502077+ 5 Extended /dev/sda5 30329 30515 1502046 82 Linux swap / Solaris Disk /dev/sdb: 400.0 GB, 400088457216 bytes 255 heads, 63 sectors/track, 48641 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Disk identifier: 0x00000000 Device Boot Start End Blocks Id System /dev/sdb1 1 48641 390708801 83 Linux Disk /dev/sdc: 250.0 GB, 250059350016 bytes 255 heads, 63 sectors/track, 30401 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Disk identifier: 0x0009f4b2 Device Boot Start End Blocks Id System /dev/sdc1 * 1 255 2048256 fd Linux raid autodetect /dev/sdc2 256 30401 242147745 fd Linux raid autodetect Disk /dev/sdd: 250.0 GB, 250059350016 bytes 255 heads, 63 sectors/track, 30401 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Disk identifier: 0x000b7f4c Device Boot Start End Blocks Id System /dev/sdd1 * 1 255 2048256 fd Linux raid autodetect /dev/sdd2 256 30401 242147745 fd Linux raid autodetect

  Read the article

• Create XFS volume on /dev/sg* device

  - by cpt.Buggy

  Now I have couple of Supermicro 24x2Tb SATA servers and I have now idea how to get access to disks. I need to create XFS volume on each of them but really don't know how to do it, because fdisk doesn't see them. # sg_scan -i /dev/sg0: scsi0 channel=0 id=0 lun=0 [em] ATA ST3250318AS CC38 [rmb=0 cmdq=0 pqual=0 pdev=0x0] /dev/sg1: scsi1 channel=0 id=0 lun=0 [em] ATA ST3250318AS CC38 [rmb=0 cmdq=0 pqual=0 pdev=0x0] /dev/sg2: scsi6 channel=1 id=8 lun=0 [em] Hitachi HDS722020ALA330 JKAO [rmb=0 cmdq=1 pqual=1 pdev=0x0] ... ... ... /dev/sg25: scsi6 channel=1 id=31 lun=0 [em] Hitachi HDS722020ALA330 JKAO [rmb=0 cmdq=1 pqual=1 pdev=0x0] /dev/sg26: scsi6 channel=3 id=0 lun=0 [em] LSILOGIC SASX36 A.1 7017 [rmb=0 cmdq=1 pqual=0 pdev=0xd] # sg_map /dev/sg0 /dev/sda /dev/sg1 /dev/sdb /dev/sg2 .. ... ... /dev/sg25 /dev/sg26 I can't use fdisk and mkfs, what should I do?

  Read the article

• why does the partition start on sector 2048 instead of 63

  - by gcb

  I had two drives partitioned the same and running 2 raid partitions on each. One died and I replaced it under warranty for the same model. While trying to partition it, the first partition can only start on sector 2048, instead of 63 that was before. Driver have different geometry as previous and remaining ones. (Fewer heads/more cylinders) old drive: $ sudo fdisk -c -u -l /dev/sdb Disk /dev/sdb: 2000.4 GB, 2000398934016 bytes 255 heads, 63 sectors/track, 243201 cylinders, total 3907029168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x000aa189 Device Boot Start End Blocks Id System /dev/sdb1 * 63 174080339 87040138+ 83 Linux /dev/sdb2 174080340 182482334 4200997+ 82 Linux swap / Solaris /dev/sdb3 182482335 3907024064 1862270865 fd Linux raid autodetect remanufactured drive received from warranty: $ sudo fdisk -c -u -l /dev/sda Disk /dev/sda: 2000.4 GB, 2000398934016 bytes 81 heads, 63 sectors/track, 765633 cylinders, total 3907029168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x000d0b5d Device Boot Start End Blocks Id System /dev/sda1 2048 ... why is that?

  Read the article

• external USB HD doesn't show up on 'sudo fdisk -l' on one Ubuntu, shows up on another (both 'precise')

  - by Menelaos

  I have a 1.5TB WD external USB HDD and two Ubuntu systems, both 'precise'. When I plug the disk on system A it doesn't show up on the output of sudo fdisk -l nor is it automatically mounted (note that that wasn't always the case - it used to appear in the past). When I plug it on system B (again Ubuntu precise) it shows up when I do a sudo fdisk -l (output appended at the end) and mounts automatically just fine. What does this discrepancy point to and what kind of diagnostics should I run / tools I should use to troubleshoot the problem? I followed the suggestion I received to do a sudo tail -f /var/log/syslog and the output is the following when I plug, unplug and replug the USB cable on System A: Sep 14 23:27:09 thorin mtp-probe: checking bus 2, device 3: "/sys/devices/pci0000:00/0000:00:13.2/usb2/2-2" Sep 14 23:27:09 thorin mtp-probe: bus: 2, device: 3 was not an MTP device Sep 14 23:28:01 thorin kernel: [ 338.994295] usb 2-2: USB disconnect, device number 3 Sep 14 23:28:04 thorin kernel: [ 341.808139] usb 2-2: new high-speed USB device number 4 using ehci_hcd Sep 14 23:28:04 thorin mtp-probe: checking bus 2, device 4: "/sys/devices/pci0000:00/0000:00:13.2/usb2/2-2" Sep 14 23:28:04 thorin mtp-probe: bus: 2, device: 4 was not an MTP device Sep 14 23:29:54 thorin AptDaemon: INFO: Quitting due to inactivity Sep 14 23:29:54 thorin AptDaemon: INFO: Quitting was requested (I guess the last two message are irrelevant). Output of sudo fdisk -l on System B $ sudo fdisk -l Disk /dev/sda: 1500.3 GB, 1500301910016 bytes 255 heads, 63 sectors/track, 182401 cylinders, total 2930277168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00070db4 Device Boot Start End Blocks Id System /dev/sda1 * 2048 2905114623 1452556288 83 Linux /dev/sda2 2905116670 2930276351 12579841 5 Extended /dev/sda5 2905116672 2930276351 12579840 82 Linux swap / Solaris Disk /dev/sdb: 250.1 GB, 250059350016 bytes 255 heads, 63 sectors/track, 30401 cylinders, total 488397168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x9c849c84 Device Boot Start End Blocks Id System /dev/sdb1 * 63 488375999 244187968+ 7 HPFS/NTFS/exFAT Disk /dev/sdg: 1500.3 GB, 1500299395072 bytes 255 heads, 63 sectors/track, 182401 cylinders, total 2930272256 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x0003e17f Device Boot Start End Blocks Id System /dev/sdg1 2048 2930272255 1465135104 7 HPFS/NTFS/exFAT

  Read the article

• Extending hard disk size after hard drive regrow without losing data

  - by Albert Widjaja

  Hi All, I wonder if this is possible to extend or regrow the Linux hard disk partition from 8 GB to 20 GB without losing the existing data on the partition ? at the moment this Ubuntu Linux is deployed on top of VMware and I've just regrow the hard drive from 8 GB into 20 GB but can't see the effect immediately. can anyone suggest how to do this without losing the data ? and I found some strange error message when i do the fdisk -l ?

  Read the article

• LVM Extend... not sure the filesystem

  - by Dan

  I would like to extend my LVM partition. First I did lvextend -L +100G /dev/server/home Now I still have to extend the filesystem. The tutorials tell me to use resize2fs, but that only works for ext2 and ext3. I'm not even sure what filesystem I have... fdisk /dev/server/home/ doesn't work... how do I know what kind of filesystem I have on my lvm partition?

  Read the article

• How can I set the disk partition alignment using linux tools?

  - by alexandrul

  After reading Disk Partition Alignment Best Practices for SQL Server, I just want to give those advices a try, but on my linux test server. What are the required parameters in order to set the partition offset (for fdisk if possible, or any other partitioning tool available on a linux live cd)?

  Read the article

• Linux partitioning problem

  - by Claudiu

  I am using cfdisk to repartition my hdd as from OS install I only got 1 big partition a swap. I wanted to resize the big partition to 1 GB /boot and use the rest of the space for an extended partition. After I do cfdisk, I recheck the partitions with fdisk -l and I get these: Disk /dev/sda: 320 GB, 320070320640 bytes 255 heads, 63 sectors/track, 38913 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Device Boot Start End Blocks Id System /dev/sda3 1 38455 308881755 f Extended LBA Warning: Partition 3 does not end on cylinder boundary. /dev/sda2 38455 38698 1951897 82 Linux swap /dev/sda1 * 38699 38913 311349654 83 Linux My problem is the Warning message, I think I know the cause, I think its because of sda1 Blocks size. How could that be soo big if Start and End interval is small?

  Read the article

• Why can't windows see mmcblk0p3? [closed]

  - by jacknad

  The partition is created on the embedded linux target like this # n - new # p - partition # 3 - partition 3 # 66 - starting cylinder # <blank> - maximum size for the ending cylinder # t - set file system type # 3 - partition 3 # c - set to windows vfat # w - write partition table and exit echo -e "n\np\n3\n66\n\nt\n3\nc\nw" | fdisk /dev/mmcblk0 The file system is then formatted on the embedded linux target as MS-DOS like this # -n volume-name # -F FAT-size mkfs.vfat -n DB -F 32 /dev/mmcblk0p3 A linux host can mount and access files in mmcblk0p3 without issue. Why can't windows? Edit: Although the default number of FATS is 2 I tried adding -f 2 [number-of-FATs] since this is actually being done by busybox on an embedded platform but this didn't help. I understand the Linux MS-DOS file system does not support more than 2 FATs but there are only 2 on this target (the boot is also FAT which is visible), along with and EXT3 (on p2) for the root file system.

  Read the article

• Fedora 17 - Dropping into debug shell after attempted partitioning

  - by i.h4d35

  So I tried creating a new partition on Fedora 17 using fdisk as follows: Command (m for help): n Command action e extended p primary partition (1-4) p Partition number (1-4): 1 First cylinder (2048-823215039, default 2048): Using default value 2048 Last cylinder or +size or +sizeM or +sizeK (1-9039, default 9039): +15G Once this was done,instead of formatting the partition I created, I ran the partprobe command to write the changes to the partition table. On rebooting the computer, it drops to the debug shell and gives me the error as follows: dracut warning:unable to process initqueue dracut warning:/dev/disk/by-uuid/vg_mymachine does not exist dropping to debug shell dracut:/# While trying to run fsck on the said partition from the debug shell, it says "etc/fstab not found" and inside /etc I see a fstab.empty file. Is it now possible to retrieve what I have from the computer? Any help would be appreciated. Thanks in advance Edit: I've also tried the following steps for additional troubleshooting: I tried to boot using the Fedora disk and tried the rescue mode - says no Linux partition detected. I tried to create an fstab file by combining the entries from blkid and the /etc/mtab file and using the UUIDs from the mtab file - It didn't work. As soon as I rebooted the machine, it promptly dropped me in to the debug shell and the fstab file which i created wansn't there anymore in /etc (part of this solution)

  Read the article

• Is my OCZ SSD aligned correctly? (Linux)

  - by Barney Gumble

  I have an OCZ Agility 2 SSD with 40 GB of space. I use it as a system drive in Debian Linux (Squeeze) and in my opinion it's really fast. But I've read a lot on aligning partitions and file systems... And I'm not sure if I succeeded in aligning the partitions correctly. Maybe the SSD could be even faster?? ;-) I use ext4 and here is the output of fdisk -cul: Disk /dev/sda: 40.0 GB, 40018599936 bytes 255 heads, 63 sectors/track, 4865 cylinders, total 78161328 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: [...] Device Boot Start End Blocks Id System /dev/sda1 * 2048 73242623 36620288 83 Linux /dev/sda2 73244670 78159871 2457601 5 Extended /dev/sda5 73244672 78159871 2457600 82 Linux swap / Solaris My partitions were created just by the Debian Squeeze setup assistant. So I didn't care about the details of partitioning. But now I think maybe the installer didn't align it correctly? Actually, 2048 looks good to me (better than odd values like 63 or something like that) but I've no idea... ;-) Help plz! According to some "SSD Alignment Calculator" I found on the web, the OCZ SSDs have a NAND Erase Block Size of 512kB and their NAND Page Size is 4kB. 2048 is divisible by 4 and 512. So are the partitions aligned correctly?

  Read the article

• Recover harddrive data

  - by gameshints

  I have a dell laptop that recently "died" (It would get the blue screen of death upon starting) and the hard drive would make a weird cyclic clicking noises. I wanted to see if I could use some tools on my linux machine to recover the data, so I plugged it into there. If I run "fdisk" I get: Disk /dev/sdb: 20.0 GB, 20003880960 bytes 64 heads, 32 sectors/track, 19077 cylinders Units = cylinders of 2048 * 512 = 1048576 bytes Disk identifier: 0x64651a0a Disk /dev/sdb doesn't contain a valid partition table Fine, the partition table is messed up. However if I run "testdisk" in attempt to fix the table, it freezes at this point, making the same cyclical clicking noises: Disk /dev/sdb - 20 GB / 18 GiB - CHS 19078 64 32 Analyse cylinder 158/19077: 00% I don't really care about the hard drive working again, and just the data, so I ran "gpart" to figure out where the partitions used to be. I got this: dev(/dev/sdb) mss(512) chs(19077/64/32)(LBA) #s(39069696) size(19077mb) * Warning: strange partition table magic 0x2A55. Primary partition(1) type: 222(0xDE)(UNKNOWN) size: 15mb #s(31429) s(63-31491) chs: (0/1/1)-(3/126/63)d (0/1/32)-(15/24/4)r hex: 00 01 01 00 DE 7E 3F 03 3F 00 00 00 C5 7A 00 00 Primary partition(2) type: 007(0x07)(OS/2 HPFS, NTFS, QNX or Advanced UNIX) (BOOT) size: 19021mb #s(38956987) s(31492-38988478) chs: (4/0/1)-(895/126/63)d (15/24/5)-(19037/21/31)r hex: 80 00 01 04 07 7E FF 7F 04 7B 00 00 BB 6F 52 02 So I tried to mount just to the old NTFS partition, but got an error: sudo mount -o loop,ro,offset=16123904 -t ntfs /dev/sdb /mnt/usb NTFS signature is missing. Ugh. Okay. But then I tried to get a raw data dump by running dd if=/dev/sdb of=/home/erik/brokenhd skip=31492 count=38956987 But the file got up to 59885568 bytes, and made the same cyclical clicking noises. Obviously there is a bad sector, but I don't know what to do about it! The data is still there... if I view that 57MB file in textpad... I can see raw data from files. How can I get my data back? Thanks for any suggestions, Solution: I was able to recover about 90% of my data: Froze harddrive in freezer Used Ddrescue to make a copy of the drive Since Ddrescue wasn't able to get enough of my drive to use testdisk to recover my partitions/file system, I ended up using photorec to recover most of my files

  Read the article

• Partition Label Problem after DD Image

  - by bobby

  After imaging a 100GB hard drive into an image file with dd, I dd'd the image to a larger hdd After boot get mkrootdev: label / not found I have gone in with finnix and relabeled the partition to the same label with e2label and still have problems. Has anyone resolved this before?

  Read the article

• Reread partition table without rebooting?

  - by Teddy

  Sometimes, when resizing or otherwise mucking about with partitions on a disk, cfdisk will say: Wrote partition table, but re-read table failed. Reboot to update table. (This also happens with other partitioning tools, so I'm thinking this is a Linux issue rather than a cfdisk issue.) Why is this, and why does it only happens sometimes, and what can I do to avoid it? Note: Please assume that none of the partitions I am actually editing are opened, mounted or otherwise in use. Update: cfdisk uses ioctl(fd, BLKRRPART, NULL) to tell Linux to reread the partition table. Two of the other tools recommended so far (hdparm -z DEVICE, sfdisk -R DEVICE) does exactly the same thing. The partprobe DEVICE command, on the other hand, seems to use a new ioctl called BLKPG, which might be better; I don't know. (It also falls back on BLKRRPART if BLKPG fails.) BLKPG seems to be a "this partition has changed; here is the new size" operation, and it looked like partprobe called it individually on all the partitions on the device passed, so it should work if the individual partitions are unused. However, I have not had the opportunity to try it.

  Read the article

• Why does Ubuntu 13.10 not detect my Win7 partition?

  - by goutham

  I'm trying to install Ubuntu 13.10 alongside Windows 7 on my DELL INSPIRON 14z 5423 laptop and I'm new to all of this. I'm using the Ubuntu 13.10 64-bit ISO burned onto a CD. The first time I tried to install it, Ubuntu said it did not detect any other OS, which meant I only had 4 options: Erase disk and install Ubuntu (I don't want to do this) Encrypt new Ubuntu. Use LVM. Something else. If I choose the Something else option, it brings me to the partition menu and says that I have 1 disk with free space of (500Gb), but that's not true because I have Windows 7. I restarted the laptop several times and booted the CD again and I got exactly the same as I did previously. How do fix this problem and install Ubuntu alongside Windows 7? After executing "sudo fdisk -l" command in terminal ubuntu@ubuntu:~$ sudo fdisk -l WARNING: GPT (GUID Partition Table) detected on '/dev/sda'! The util fdisk doesn't support GPT. Use GNU Parted. Disk /dev/sda: 500.1 GB, 500107862016 bytes 255 heads, 63 sectors/track, 60801 cylinders, total 976773168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 4096 bytes I/O size (minimum/optimal): 4096 bytes / 4096 bytes Disk identifier: 0xd2b811c5 Device Boot Start End Blocks Id System /dev/sda1 * 2048 206847 102400 7 HPFS/NTFS/exFAT /dev/sda2 206848 314574847 157184000 7 HPFS/NTFS/exFAT /dev/sda3 314574848 629147647 157286400 7 HPFS/NTFS/exFAT /dev/sda4 629147648 976771071 173811712 7 HPFS/NTFS/exFAT After removing one partition I executed command once again ubuntu@ubuntu:~$ sudo fdisk -l WARNING: GPT (GUID Partition Table) detected on '/dev/sda'! The util fdisk doesn't support GPT. Use GNU Parted. Disk /dev/sda: 500.1 GB, 500107862016 bytes 255 heads, 63 sectors/track, 60801 cylinders, total 976773168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 4096 bytes I/O size (minimum/optimal): 4096 bytes / 4096 bytes Disk identifier: 0xd2b811c5 Device Boot Start End Blocks Id System /dev/sda1 * 2048 206847 102400 7 HPFS/NTFS/exFAT /dev/sda2 206848 629145599 314469376 7 HPFS/NTFS/exFAT /dev/sda3 629147648 976771071 173811712 7 HPFS/NTFS/exFAT

  Read the article

• Linux not picking up new partition correctly on emc pseudo device

  - by James

  Hi We have a database server running oracle rac. We were recently running out of space on the main LUN that it is attached to. I created a new 100GB LUN and concatenated this onto the existing LUN creating a new MetaLUN. After some messing I managed to get linux to recognise the new space. I then created a new partition in on the pseudo device, to use the new space. Previously when I have done this on other system the next step is to create an ASM disk on the new partition and add this disk to the oracle disk group. This however fails. I am aware of various issues with ASM and powerpath, but I don't think this is the issue here. As on while investigating the issue I discovered that one of the underlying logical device is not reflecting the size change. See below; Powermt displays all of the underlying logical units [root@XXXXX~]# powermt display dev=emcpowerd Pseudo name=emcpowerd CLARiiON ID=CKM00091500009 [VFRAC2] Logical device ID=6006016030312200787502866C65DE11 [LUN 30] state=alive; policy=CLAROpt; priority=0; queued-IOs=0 Owner: default=SP A, current=SP A Array failover mode: 1 ============================================================================== ---------------- Host --------------- - Stor - -- I/O Path - -- Stats --- ### HW Path I/O Paths Interf. Mode State Q-IOs Errors ============================================================================== 3 qla2xxx sde SP A0 active alive 0 0 3 qla2xxx sdj SP B0 active alive 0 0 4 qla2xxx sdo SP A1 active alive 0 0 4 qla2xxx sdt SP B1 active alive 0 0 Fdisk on the pseudo device shows correct space. [root@XXXXX ~]# fdisk -l /dev/emcpowerd Disk /dev/emcpowerd: 429.4 GB, 429496729600 bytes 255 heads, 63 sectors/track, 52216 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Device Boot Start End Blocks Id System /dev/emcpowerd1 1 39162 314568733+ 83 Linux /dev/emcpowerd2 39163 52216 104856255 83 Linux fdisk on one of the logical units is wrong [root@XXXXX~]# fdisk -l /dev/sde Disk /dev/sde: 322.1 GB, 322122547200 bytes 255 heads, 63 sectors/track, 39162 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Device Boot Start End Blocks Id System /dev/sde1 1 39162 314568733+ 83 Linux /dev/sde2 39163 52216 104856255 83 Linux fdisk on the rest of the units is fine [root@XXXXX ~]# fdisk -l /dev/sdj Disk /dev/sdj: 429.4 GB, 429496729600 bytes 255 heads, 63 sectors/track, 52216 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Device Boot Start End Blocks Id System /dev/sdj1 1 39162 314568733+ 83 Linux /dev/sdj2 39163 52216 104856255 83 Linux Also when I created the the partition linux did not create the any entries in the /dev directory for the second partition so I created these manually [root@XXXXX dev]# mknod sde2 b 8 66 [root@XXXXX dev]# ls -al sd[ejot]? brw-r----- 1 root disk 8, 65 Dec 29 14:20 sde1 brw-r--r-- 1 root disk 8, 66 Apr 8 20:31 sde2 brw-r----- 1 root disk 8, 145 Dec 29 14:19 sdj1 brw-r--r-- 1 root disk 8, 146 Apr 8 20:33 sdj2 brw-r----- 1 root disk 8, 225 Apr 6 23:12 sdo1 brw-r--r-- 1 root disk 8, 226 Apr 8 20:33 sdo2 brw-r----- 1 root disk 65, 49 Dec 29 14:19 sdt1 brw-r--r-- 1 root disk 65, 50 Apr 8 20:33 sdt2 This is a production server that we cannot easily reboot. Any ideas would be much appreciated. J

  Read the article

• How do I mount a "DiskSecure Multiboot" partition?

  - by ????

  For a hard drive that has 4 or 5 partitions, I was able to mount one of them using Ubuntu LiveCD: sudo mount /dev/sda1 /mnt but is there a way to mount to the other partitions? (if using sudo fdisk -l, it only shows /dev/sda) GParted's snapshot is: Right now, the fdisk info is as follows: ubuntu@ubuntu:~$ sudo fdisk -l /dev/sda Disk /dev/sda: 320.1 GB, 320072933376 bytes 255 heads, 63 sectors/track, 38913 cylinders, total 625142448 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x1aca8ea5 Device Boot Start End Blocks Id System /dev/sda1 284993226 350602558 32804666+ 7 HPFS/NTFS/exFAT and then ubuntu@ubuntu:/mnt$ sudo fdisk -l /dev/sda1 Disk /dev/sda1: 33.6 GB, 33591978496 bytes 255 heads, 63 sectors/track, 4083 cylinders, total 65609333 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x2052474d This doesn't look like a partition table Probably you selected the wrong device. Device Boot Start End Blocks Id System /dev/sda1p1 ? 6579571 1924427647 958924038+ 70 DiskSecure Multi-Boot /dev/sda1p2 ? 1953251627 3771827541 909287957+ 43 Unknown /dev/sda1p3 ? 225735265 225735274 5 72 Unknown /dev/sda1p4 2642411520 2642463409 25945 0 Empty Partition table entries are not in disk order Per @lgarzo's request, parted info is: ubuntu@ubuntu:/mnt$ sudo parted /dev/sda print Model: ATA ST3320820AS (scsi) Disk /dev/sda: 320GB Sector size (logical/physical): 512B/512B Partition Table: msdos Number Start End Size Type File system Flags 1 146GB 180GB 33.6GB primary ntfs boot The command sudo mount /dev/sda1p2 /mnt won't work.

  Read the article

• How does Google Chrome know my Firefox history if I never imported it?

  - by fdisk

  I have Firefox and Google Chrome installed in the same machine (Linux). It happens when I type something in Chrome Omnibox it suggests pages I have already visited in Firefox. I have never connected the accounts of both browsers I have never imported information from one browser to other I have never visited the suggested pages in Chrome The keyword I type in the omnibox is vague and there is no way it could guess the suggestion without having access to the Firefox history. i.e.: i type "ir" in Chrome and it suggests me the same Iron Maiden lyrics page I have browse before in Firefox. Thanks

  Read the article

• How to rescue from an SD (SDHC) card that I can't reformat (possible hardware failure)

  - by sbwoodside

  I have a transcend 16GB SDHC card and a lot of photos on it that I'd like to recover. When I plug it into the SD card reader, it takes a while for the Mac to even recognize that there's a disk present, and it shows up as 1.07GB with geometry 520/64/63 (according to fdisk). First I tried file recovery: PhotoRec: no files are found (the images are in CR2 format and I'm using testdisk-6.14-WIP which claims to recognize that format under TIF) dd / ddrescue: they create a 1.07GB image, same problem as above TestDisk: doesn't find any partitions to recover I found a source saying that the correct geometry for this type of SD Card is Heads 255, Sectors/Track 63, Cylinders 1953, so I tried manually setting that geometry in PhotoRec/TestDisk. No improvement. Next I tried formatting the disk with fdisk. After writing and quitting, I ran fdisk again and it reported that the new format hadn't been saved on the disk. I also tried resetting the format/partitions with TestDisk and that failed also. The fdisk log is below. I don't really care about the card, I've already ordered a new SanDisk card. But I'd like to get the data off. Maybe, is there any way to force dd or some other tool to create an image of the disk based on the original geometry and not on what the card "thinks" its geometry is? Or am I missing something?

  Read the article

< Previous Page | 1 2 3 4 5 6 7 8 9 10 11 12  | Next Page >