Search Results

Search found 10515 results on 421 pages for 'automatically'.

Page 200/421 | < Previous Page | 196 197 198 199 200 201 202 203 204 205 206 207  | Next Page >

• Multi Gateway and Backup Routing on a cisco router

  - by user64880

  Hi all, I have a 2611 Cisco Router with only one Fastethernet port Now I have two internet gateways. I want to config my router as when primary routing fails second routing automatically start to route all my packets. When I set 2 IP route command in my router then I check I see it work well but when peer IP on primary routing is down it can not change to second routing until I remove first route command.In the following I write my setting. How can I set it? interface FastEthernet0/0 ip address 81.12.21.100 255.255.255.248 secondary ip address 62.220.97.14 255.255.255.252 ip route 0.0.0.0 0.0.0.0 62.220.97.13 ip route 0.0.0.0 0.0.0.0 81.12.21.97 100 Cheer, Kamal

  Read the article

• How likely can my data be recovered after Windows CHKDSK performed on a degraded RAID 5 array?

  - by chrisling106

  Hello there, We have a RAID 5 setup with 3 SATA disks, #2 went down as reported on the pre-POST screen. Unfortunately, for some reason out of my control, the system was rebooted with a degraded RAID :-O Windows XP (64-bit) loaded, CHKDSK ran automatically and done its recovery! From that point onwards, the following error prompts every time even in Safe Mode: lsass.exe - The endpoint format is invalid I took those 3 disks to the data recovery expert and need to wait at least 2-4 days for results. There are 2 VMs on multiple files stored in this RAID 5 array, and there's no backup! Sorry, I just inherited the system from an ex-staff who has left the company 2 months before I joined. How likely the data can be recovered?

  Read the article

• Is there a way to bundle pdf tiles to a Kindle friendly file?

  - by Maciej Swic

  I'm downloading PDF approach plates from Navigraph, and i have a folder per airport with files named after their corresponding approach / departure etc. Now I'd like to take such a folder with a bunch of PDF files, automatically generate an index and combine them to a single .mobi file that i can send to my Kindle. The index created can be very simple and consist of the file name (without the extension). Tapping an index item should jump to the correct page for that chart. I know there is a host of apps that combine comic book jpg's to ebooks, but is there anything that does the above please?

  Read the article

• How can I get black window borders in Windows 8?

  - by sean e

  In Windows 8, when I go into Control Panel\Appearance and Personalization\Personalization\Window Color and Appearance the amount of control over window colors is greatly reduced as compared to Windows 7. The color controls do not allow you to make Window borders display in black. Is there some other way to set the window border color in Windows 8? Edit 1: Clearly the standard way does not work in Windows 8. The question is, is there another way? Perhaps through the registry for example? Edit 2: I tried copying the values in HKEY_CURRENT_USER\Software\Microsoft\Windows\DWM from my Win7 system to the Win8 system without success (killing the 2 DWM processes after each change - they are automatically restarted and do use the new values).

  Read the article

• Auto-resize images in Opera

  - by Nick

  Is there a setting that I can configure to automatically scale large images like Firefox does? I'm using Opera 10.53, and when I open a large image in a new tab, it is not scaled at all. I'm on a laptop, so it is hard to view, and when I am viewing multiple images, it is tedious to scale each image down to 20% or whatever fits it best. I found this thread, and for a fleeting moment thought I had found the answer, but apparently not. They just told the poster to manually resize. Thanks.

  Read the article

• Force a Windows 7 user to change password when it has expired

  - by Joshua King

  Is it possible to force users (on Windows 7 PCs) to change their password once it has expired? Currently our users get notifications that their passwords will expire in 7, 3, 2 and 1 days but once the password has expired they are still able to log into their machines with the expired password. Most of our users ignore the warnings and don't change their password until we tell them they have to (when they ring Help Desk asking why their email and intranet isn't working). From memory, Windows XP machines would show a message at login that the password had expired and then offer the change password screen. Is it possible to do the same thing under Win7? Similar to how if you set a user's account to "must change password at next login" it gives the change password screen automatically.

  Read the article

• Optimum number of threads while multitasking

  - by Gun Deniz

  I know similar questions have been asked but I think my case is a little bit diffrent. Let's say I have a computer with 8 cores and infinite memory with a Linux OS. I have a calculation software called Gaussian that can take advantage of multithreading. So I set its thread count to 8 for a single calculation for maximum speed. However I really can't decide what to do when I need to do run for instance 8 calculations simultaneously. In that case should I set the thread count to 1(total 8 threads spawned in 8 processes) or keep it 8(total 64 threads spawned in 8 processes) for each job? Does it really matter much? A related question is does the OS automatically does the core-parking to diffrent cores for each thread?

  Read the article

• How to kick Jawbone ICON off iPhone to use with Mac

  - by SeniorShizzle

  I've got a Jawbone ICON, which is paired to my PS3, my Macbook Air, and my iPhone 4. Most of the time I'm using it with my Macbook with A2DP. The problem is that when I turn it on, my iPhone automatically connects to it, and hogs the A2DP profile, so then my Mac can't connect to the thing at all. I sort of like this behavior, so my best solution would be if there was some way to "kick" the ICONs connection to my iPhone from my Mac. It's really difficult because I use it alot with my Mac and my iPhone, so I can't delete one of the profiles, and I need to use A2DP on both devices. What are your suggestions on ways to fix this?

  Read the article

• Add a hook to run when NetworkManager connects

  - by rplevy

  What would be a good way to make a script run every time my computer connects to the network in Ubuntu? Would I somehow use dbus to do this? Background: when I'm on the train I run a short Perl script to click a button on the splash page. That way I can immediately use the internet without having to manually visit a pointless website. My script is a near-perfect solution, but it would be perfect if it could run automatically any time I connect to the network.

  Read the article

• How to color highlight text in a black/white document easily

  - by Lateron

  I am editing a 96 chapter book. The text is in normal black letters on a white background. What I want to be able to do is: I want to have any changes or additions automatically shown in another (per-selected) color. Without having to a)high lite a word or phrase to be changed or added and then b)going to the toolbar and clicking on the font color In other words I want the original color of the text to remain as it is and any additions or changes to be visible in another color without having to use the toolbar. Can this be done? I use OpenOffice or Word 2007 in Windows 7.

  Read the article

• PDF Encrypted, Hidden Watermark

  - by Dave Jarvis

  Background Using LaTeX to write a book. When a user purchases the book, the PDF will be generated automatically. Problem The PDF should have a watermark that includes the person's name and contact information. Question What software meets the following criteria: Applies encrypted, undetectable watermarks to a PDF Open Source Platform independent (Linux, Windows) Fast (marks a 200 page PDF in under 1 second) Batch processing (exclusively command-line driven) Collusion-attack resistant Non-fragile (e.g., PDF - EPS - PDF still contains the watermark) Well documented (shows example usages) Ideas & Resources Some thoughts and findings: Natural language processing (NLP) watermarks. Apply steganography on a randomly selected image. http://openstego.sourceforge.net/cmdline.html The problem with NLP is that grammatical errors can be introduced. The problem with steganography is that the images are sourced from an image cache, and so recreating that cache with watermarked images will impart a delay when generating the PDF (I could just delete one image from the cache, but that's not an elegant solution). Thank you!

  Read the article

• Norton Backup "Failed to Restore"

  - by Teknophilia

  I recently had one of my computers (XP) die on me. I had it's files set to automatically backup to another PC's HD using Norton. I've tried using Norton restore on the second computer to try and restore some files (word documents, pictures), but when I try to do this, I get a dialog box saying that it "Failed to Restore". When I click to continue, it shows a list of the files I tried to restore, along with a status indicator for each file (which says "invalid file"). Any ideas?

  Read the article

• Google "not selecting" many of the links on my site

  - by Loki

  Since a few days I noticed that Google wasn't indexing any of the pages on my site anymore. When I checked the indexingstatus-page I noticed the following: As you can see the "not selected"-line is going thru the roof! The information on google's help pages is very limited: https://support.google.com/webmasters/bin/answer.py?hl=nl&answer=139066 I run a free downloads-site which is automatically updated. I don't have duplicate content (except that sometimes descriptions of software is similar over an older version of the software) and my URL's are all forwarded to the www.-variant from within Wordpress. So the canonical-part that Google mentions in their Help-file, isn't the problem. Any ideas what could be causing this and how to solve it?

  Read the article

• How to set up a staging apt repository to securely manage upgrades

  - by andreash

  Hello, I would like to be able to run automatic apt-get upgrade (once per hour) on our servers (Ubuntu 10.04), so that I don't have to do it manually on all of them (about 15). However, for production machines, that's not a good idea ... So here's my idea: Set up a local repository for all 'approved' updates for critical packages. I would then push updated packages from upstream to our local repo after I tested them, and all servers could automatically (apt-cron?) upgrade from this repository. So my question is this: How do I configure apt on the clients so that they use the local repository only for all packages which exist on the local repository, and the upstream one for all other packages? Does this actually make sense? Or am I missing something? Anyways, thanks for your insight! Andreas.

  Read the article

• Foremost custom file type not accepted by -t argument

  - by Channel72

  I'm trying to recover a deleted file on an ext3 file system using the foremost utility. The file I want to recover is a hpp C++ source code file. However, foremost does not automatically support the hpp file extension, so I have to add it to the config file. So, following the instructions on the man page, I add the following line to the config file: hpp n 50000 include include ASCII Then I run foremost as follows: $foremost -v -T -t hpp -i /dev/md0 -o /home/recover/ Instead of doing anything, it just displays the help message. If I change the hpp to htm or jpg, it works. So apparently foremost isn't accepting the custom file type I added into the config file. But I've looked over this dozens of times now, and I can't see what I'm doing wrong. I'm following the instructions exactly. Why doesn't foremost recognize the new file type I added to the config file?

  Read the article

• Make Exchange 2007 use the correct SSL certificate

  - by Neil

  I have an SBS 2008 server contososerver.contosodomain.local which is externally accessible with the domain remote.contoso.com and an SSL certificate for the external domain which we installed using the SBS 2008 wizard. This works great for OWA because IIS serves the remote.contoso.com certificate. I also want to turn on external POP3/IMAP4/SMTP however when I try, I get served the internal certificate that SBS generated automatically (using its internal CA) which has the alternate names remote.contoso.com, contososerver.contosodomain.local and contososerver. I tried removing this certificate from Exchange but it won't let me because it needs it for its internal receive connector. So how do I tell Exchange 2007 to use the real certificate for external POP3/IMAP4/SMTP?

  Read the article

• Allow users to view Word documents only and not be able to edit, copy or save them.

  - by Alexander

  Hello In a traditional Windows Server 2003 environment with AD, we have shared a folder for our policy documents (MS Word). These documents get edited/updated now and then by the administrator(principal of college). Users only have read-only access to the folder, but they can still save-as and then change the content. Sharepoint is a possible solution but not easy to implement. We also thought of using a CMS on Linux and installing Joomla to let users only view the docs with a document management system... but is it possible to automatically retrieve the policy folder on the network and convert or put it in a format that users can only view and not copy? We also thought of saving the docs to secure pdf format but the principal wants an automated system. Basically she just wants to work in Word and the policies must be available to staff members on the network. Any ideas? Much appreciated.

  Read the article

• Stop jucheck from running

  - by Ken

  I've installed Java on Windows Vista, and every day I get a Vista security warning asking me if I want to run "jucheck". Apparently this is the Java automatic updater. Well, I don't want it to run on its own, ever. I cancel it, and quit it. I right-click on the taskbar and unclick "Check for Updates Automatically", and then click "Never Check", and "Apply". And yet, it never remembers this setting. If I come back to the "Java Control Panel" right after clicking "OK", the very same box is checked again, all on its own. Is there some way to kill jucheck once and for all? If I simply delete jucheck.exe, will Java (other than the automatic check) still work, and will manual updates still work, and will it stop even trying to update every morning?

  Read the article

• Two-page view in Word, shouldn't the first page be on the right?

  - by Cylindric

  Greetings Superusers, I'm putting together a lengthy document in Word, and it's going to be printed and bound duplex. I've put page-numbers "outside" etc, and all is pretty. The problem is, in the "Two Pages" view, it puts p1 on the left, then p2 on the right, then p3 below on the left, and p4 on the right. p1 p2 p3 p4 p5 p6 Shouldn't this be slightly different though? When I get to print it, p1 is on the right, not the left, so the preview should go p1 p2 p3 p4 p5 p6 Because when I "open" the book, it's pages 2 and 3 that are side-by-side. This makes layout tweaking confusing, because it's not instantly obvious which pages will be "visible" to the reader at the same time together. Have I missed something? I can't just put a blank page first, because that would bugger up the printing, as the printer automatically duplexes and binds etc. (Office 2008, by the way)

  Read the article

• Problems with webcam

  - by Murtaza

  My friend is using Windows 8.1, and he has a webcam. He says it is working very well even without installing drivers. Webcam is A4tech - PK-331F. I asked for this webcam for use. I plugged in the webcam, and Windows detected it and installed drivers automatically. Then I opened Skype to check the webcam. I got a message from Skype that said, "Your webcam has microphone." When I clicked over it, it directed me to sound settings where it showed that the webcam microphone was working. I went to video settings, but the webcam wasn't listed there. As you can see in the image, the webcam is not listed. It is listed in Device Manager but isn't listed in Skype. I am using Windows 7 Professional. Any idea why this is happening?

  Read the article

• Dual-WAN router

  - by aix

  I am looking for a router that would fit the following requirements: Two WAN interfaces: the primary is PPPoE, the secondary will link to a GigE port on another router (a 100Mbps link will suffice); Two (ideally four) GigE LAN ports; No requirement for a firewall; No requirement for Wi-Fi; Inexpensive. The plan for the two WAN interfaces is as follows. All outbound traffic will go to the primary, with exceptions based on destination IP/subnet or possibly on src+dest IPs/subnets. Such exceptions should be routed to the secondary. It would be very nice if, should the primary go down, the secondary would automatically take over for all outbound traffic. I am reasonably sure that I can put something together based on dd-wrt. However, I'd like to hear from you what alternatives are out there (especially something easier to set up for my use case, even if it means paying more for the hardware.)

  Read the article

• Amavis / Atermime - Dynamic Email Signatures (Disclaimers)

  - by Frank

  I am running a basic iredmail install with amavis, postfix, dovecot. I want to use the declaimer feature to automatically append a disclaimer (in our case a signature). The reasoning for this is that clients (ipad, outlook, etc) don’t have to be configured with signature settings, and that we have corporate control over the actual signatures that are posted. Instead of: '[email protected]' => 'boss.domain.com.txt' I am trying to get to %mailbox + ‘@’ + %domain => %mailbox + “.” + %domain + ‘.txt’ This way we can simply use a script to generate the .txt / .htm signature files using just mysql / php. THANKS IN ADVANCE

  Read the article

• Use Windows Briefcase from the command line

  - by Daniel

  I have a thumb drive on which I take many of my files with me. I would like to synchronize it with my computer automatically when I connect it. I currently have a script run every time I connect it so that I can do the many things that need to be done when it connects (check for updates to the portable applications, etc.). I want my synchronization utility to: Detect conflicts work correctly when I move files or change the folder structure tell the difference between a file that was deleted on one side and a file that was added on the other work from the command line or at least have a command that will open up a window provide a confirmation screen before doing anything The Windows Briefcase does all of these except the command line. Is there any program that does all of these, or is there a way to synchronize the briefcase from the command line?

  Read the article

• Move icons around freely in Windows 7

  - by Eikern

  I just installed a pre-RTM build of Windows 7 that I downloaded from Microsoft, so this may have changed in the RTM version, but I do not think so. (EDIT: Same thing in the released version.) In Windows Vista, XP and older you could move icons around freely within a folder, rearranging them like I wanted them -- even though it was automatically ordering the position of them. So I could move a file starting with 'B' down below 'M'. I know this is kind of 'wrong', but is this possible? Thanks.

  Read the article

• How to choose my own filename format for subscribed podcast files?

  - by meomaxy

  I subscribe to several podcasts where the filenames of the downloaded mp3 files have no particular pattern to them. When I copy the directory of accumulated mp3 files into my mp3 player, the files play in alphabetical order. What I really want is to play the files chronologically by release date. I currently use iTunes on Windows XP to download the files. What I do now is manually rename the files, adding the date in YYYYMMDD format to the start of each filename so that an alphabetical listing of files will correspond to their chronological order when I listen to them later in PocketTunes on my Palm Centro. Is there some way to get the release date into the filename automatically? If so, I could automate or possibly skip the file renaming step. I would switch from iTunes to something else if that would solve my problem. The file creation time on my local disk isn't a reliable indicator because sometimes I download a few days worth of content at one time, and the files don't necessarily get downloaded in chronological order.

  Read the article

< Previous Page | 196 197 198 199 200 201 202 203 204 205 206 207  | Next Page >