Search Results

Search found 7850 results on 314 pages for 'except'.

Page 201/314 | < Previous Page | 197 198 199 200 201 202 203 204 205 206 207 208  | Next Page >

• Windows XP corrupts registry every several hours

  - by Ilya Kazakevich

  There is a Dell XPS 400 with Windows Media Center installer. It is installed on RAID (Intel Matrix Storage) which is built-in chipset south bridge. Raid has two 150 Gb WDC drivers connected as mirror. All drivers and updates are installed( sp3 and so on). A week ago PC changed its video mode to 256 colors (like VESA mode) and after several moments I got BSOD: c000021a: 0xc0000005 Doctor watson did not create dump although it is installed as default debugger. After reboot it said that config file is missing or corrupted. So, I boot to recovery console and found that registry file (config) is so small. I've replaced it with one from recovery point and windows booted sucessfully. But after about 3 hrs -- it has crashed again in the same wat! I look in event viewer: is said that Explorer.exe failed to open \global??\DLIAFS. I look in winobj, and found that it is a device. I made "deny from everyone" for this device ACL, and after several hours my windows crashed. I restored registry, boot again and there was no error about DLIAFS. I did full chkdsk and it did not found anything bad. But I found event about error paging to \Harddrive1\D. I do not have pagefile there, but I thought I should check my disk again. Unfortunatelly I cannt use smart tools for RAID, but I downloaded latest software from Intel (it can do the same things like RAID bios can but from windows). It verified my disks, found some errors, fix them, than I rebooted. And it crashed again. I am lost. What (except kernel debugging) could be done here? Thanks

  Read the article

• Windows XP corrupts registry every several hours

  - by Ilya Kazakevich

  There is a Dell XPS 400 with Windows Media Center installer. It is installed on RAID (Intel Matrix Storage) which is built-in chipset south bridge. Raid has two 150 Gb WDC drivers connected as mirror. All drivers and updates are installed( sp3 and so on). A week ago PC changed its video mode to 256 colors (like VESA mode) and after several moments I got BSOD: c000021a: 0xc0000005 Doctor watson did not create dump although it is installed as default debugger. After reboot it said that config file is missing or corrupted. So, I boot to recovery console and found that registry file (config) is so small. I've replaced it with one from recovery point and windows booted sucessfully. But after about 3 hrs -- it has crashed again in the same wat! I look in event viewer: is said that Explorer.exe failed to open \global??\DLIAFS. I look in winobj, and found that it is a device. I made "deny from everyone" for this device ACL, and after several hours my windows crashed. I restored registry, boot again and there was no error about DLIAFS. I did full chkdsk and it did not found anything bad. But I found event about error paging to \Harddrive1\D. I do not have pagefile there, but I thought I should check my disk again. Unfortunatelly I cannt use smart tools for RAID, but I downloaded latest software from Intel (it can do the same things like RAID bios can but from windows). It verified my disks, found some errors, fix them, than I rebooted. And it crashed again. I am lost. What (except kernel debugging) could be done here? Thanks

  Read the article

• Cannot login to ISCSI Target - hangs after sending login details

  - by Frank

  I have an ISCSI target volume, to which i am trying to connect using CentOS Linux server. Everything works fine, but cannot its stuck at login. Here are the steps i am performing: [root@neon ~]# iscsiadm -m node -l iscsiadm: could not read session targetname: 5 iscsiadm: could not find session info for session20 iscsiadm: could not read session targetname: 5 iscsiadm: could not find session info for session21 iscsiadm: could not read session targetname: 5 iscsiadm: could not find session info for session22 iscsiadm: could not read session targetname: 5 iscsiadm: could not find session info for session23 iscsiadm: could not read session targetname: 5 iscsiadm: could not find session info for session30 iscsiadm: could not read session targetname: 5 iscsiadm: could not find session info for session31 iscsiadm: could not read session targetname: 5 iscsiadm: could not find session info for session78 iscsiadm: could not read session targetname: 5 iscsiadm: could not find session info for session79 iscsiadm: could not read session targetname: 5 iscsiadm: could not find session info for session80 iscsiadm: could not read session targetname: 5 iscsiadm: could not find session info for session81 Logging in to [iface: eql.eth2, target: iqn.2001-05.com.equallogic:0-8a0906-ab4764e0b-55ed2ef5cf350a66-neon105, portal: 10.10.1.1,3260] (multiple) After this step, its stucks, waits for some time and then gives this output: Logging in to [iface: iface1, target: iqn.2001-05.com.equallogic:0-8a0906-ab4764e0b-55ed2ef5cf350a66-neon105, portal: 10.10.1.1,3260] (multiple) iscsiadm: Could not login to [iface: eql.eth2, target: iqn.2001-05.com.equallogic:0-8a0906-ab4764e0b-55ed2ef5cf350a66-neon105, portal: 10.10.1.1,3260]. My iscsi.conf is this: node.startup = automatic node.session.timeo.replacement_timeout = 15 # default 120; RedHat recommended node.conn[0].timeo.login_timeout = 15 node.conn[0].timeo.logout_timeout = 15 node.conn[0].timeo.noop_out_interval = 5 node.conn[0].timeo.noop_out_timeout = 5 node.session.err_timeo.abort_timeout = 15 node.session.err_timeo.lu_reset_timeout = 20 node.session.initial_login_retry_max = 8 # default 8; Dell recommended node.session.cmds_max = 1024 # default 128; Equallogic recommended node.session.queue_depth = 32 # default 32; Equallogic recommended node.session.iscsi.InitialR2T = No node.session.iscsi.ImmediateData = Yes node.session.iscsi.FirstBurstLength = 262144 node.session.iscsi.MaxBurstLength = 16776192 node.conn[0].iscsi.MaxRecvDataSegmentLength = 262144 discovery.sendtargets.iscsi.MaxRecvDataSegmentLength = 32768 node.conn[0].iscsi.HeaderDigest = None node.session.iscsi.FastAbort = Yes Also, in access control, i have given full access to Any IP, Any CHAP user and fixed iscsi initiator name. With same access level, all other volumes on rest of servers are working, except this one.

  Read the article

• Windows Task Scheduler fails at sending e-mail

  - by Marki

  The error is 2147746321. I can see in the mailserver log that it tries, but the connection gets closed. Wed 2012-10-10 15:55:25: Session 990590; child 1 Wed 2012-10-10 15:55:25: Accepting SMTP connection from [x:49161] to [y:25] Wed 2012-10-10 15:55:25: --> 220 Mdaemon; Wed, 10 Oct 2012 15:55:25 +0200 Wed 2012-10-10 15:55:25: <-- EHLO x Wed 2012-10-10 15:55:25: --> 250-Hello x, pleased to meet you Wed 2012-10-10 15:55:25: --> 250-VRFY Wed 2012-10-10 15:55:25: --> 250-EXPN Wed 2012-10-10 15:55:25: --> 250-ETRN Wed 2012-10-10 15:55:25: --> 250-AUTH LOGIN Wed 2012-10-10 15:55:25: --> 250-8BITMIME Wed 2012-10-10 15:55:25: --> 250 SIZE 20971000 Wed 2012-10-10 15:55:25: <-- AUTH LOGIN Wed 2012-10-10 15:55:25: --> 334 VX...... Wed 2012-10-10 15:55:25: Connection closed Wed 2012-10-10 15:55:25: SMTP session terminated (Bytes in/out: 26/212) Googling does not reveal much except that it indeed "doesn't work" and Exchange pops up all over the place. This is no Exchange server. I just want a plain and straight SMTP connection to work. How? (I have tried running the task as normal user and as system account, no difference.)

  Read the article

• Some clients cannot connect to Server 2008 R2 VPN

  - by Robl

  Hi all, Have a server 2008 r2 setup as a VPN server. We have created a windows group to control access to the VPN called vpn-users. Clients are all Windows 7 Pro. This all seems to work fine except some users cannot connect to the VPN! For example I try to logon to the VPN from a client and get an error saying the server refused the connect due to a policy in place. Specifically authentication type! Fine I think. So i drop that user into the vpn-users group created for this and try again and hey presto the user can now logon! Great. Now try this with another user. But this time I get the same error even though I have dropped them into the vpn-users group!! So does anyone have any idea why this works for some users and not for others?? I have tried moving the user from certain OU's in AD to others, copying the account, taking the user out of the vpn-users group and then back in but get the same error each time. Any thoughts anyone?

  Read the article

• Remote assistance from Remote Desktop sessions: unable to control

  - by syneticon-dj

  Since Remote Control (aka Session Shadowing) is gone for good in Server 2012 Remote Desktop Session hosts, I am looking for a replacement to support users in a cross-domain environment. Since Remote Assistance is supposed to work for Remote Desktop Sessions as well, I tried leveraging that for support purposes by enabling unsolicited remote assistance for all Remote Desktop Session Hosts via Group Policy. All seems to be working well except that the "expert" seems to be unable to actually excercise any mouse or keyboard control when the remote assistance session has been initiated from a Remote Desktop session itself. Mouse clicks and keyboard strokes from the "expert" session (Server 2012) seem to simply be ignored even after the assisted user has acknowledged the request for control. I would like to see this working through RD sessions for the support staff due to a number of reasons: not every support agent would have the appropriate client system version to support users on a specific terminal server (e.g. an agent might have a Windows Vista or Windows 7 station and thus be unable to offer assistance to users on Server 2012 RDSHs) a support agent would not necessarily have a station which is a member of the specific destination domain (mainly due to the reason that more than a single domain's users are supported) what am I missing?

  Read the article

• DNS issue for internal website routing internet connection from remote location

  - by Michael Paul

  I have an issue that I could use some help with. Our company has a main location and a remote location. Previously, the remote location was connected to the main location through an internet connection VPN tunnel. The connection was pitifully slow at 1.5Mbps, so we upgraded it with a 75Mbps direct link. That meant the remote location lost it's internet access, so we routed their access through the main office internet connection. Everything works perfect except for one thing. The website we host is not accessible from the remote location unless the IP address is used. If I do NSLOOKUP on our website address from a machine connected to the main location network, it resolves correctly to the inside IP address. However, if I do the same from a remote location machine, it resolves to the website's outside IP address. Our internal DNS server(s) have a pointer and CNAME records set up, and everything was working perfectly before the connection was upgraded. In addition, the remote location has a domain controller, DNS server and DHCP server to service these requests at the remote location and prevent these requests from getting routed back and forth over the link. So I think was it happening is that for some reason the DNS server at the remote location is not resolving our website name correctly and passing the requests on to the routers, which then push the request out to the internet DNS system. That resolves the name to our external IP. This is purely a DNS issue, everything else works just fine. I am just stumped on this one. Any ideas on how to fix this? Edit: I forgot to mention that at the remote side of the link is a Cisco ASA-5505 and at the main office there is a Cisco ASA-5510. The link is connected between these 2 devices and the routing is handled in the 5510. Thanks, Michael

  Read the article

• Unable to Access Certain Websites

  - by codejoust

  Through a local network, all computers except one ubuntu machine can access 1. Adobe.com 2. Icann.org 3. Apache.org 4. Example.com. The ubuntu machine returns (in firefox): "Though the site seems valid, the browser was unable to establish a connection." Furthermore, when I traceroute those websites using the ubuntu machine, they all return ubuntu.local, and it ends there: (traceroute to icann.org (192.0.32.7), 30 hops max, 40 byte packets 1 ubuntu.local (192.168.1.105) 3000.791 ms !H 3000.808 ms !H 3000.814 ms !H I've checked the hosts file, and there isn't anything in there, and I have an apache server there so if it was redirected to localhost, I'd probably see the localhost webroot page. Thanks in advance! user@ubuntu:~$ netstat -nr Kernel IP routing table Destination Gateway Genmask Flags MSS Window irtt Iface 169.254.0.0 0.0.0.0 255.255.0.0 U 0 0 0 eth1 192.0.0.0 0.0.0.0 255.0.0.0 U 0 0 0 eth1 0.0.0.0 192.168.1.1 0.0.0.0 UG 0 0 0 eth1 The Ubuntu Machine is one of six on the network. I'm using opendns for dns, so I do think that should be a problem.

  Read the article

• Can I have damaged a CPU ?

  - by Pascal

  Hey guys, This is a question I asked on Anantech forums, but I just discovered this community and think this question would fit right in. Here goes: I built a PC around a Q9550 1 1/2 years ago (MoBo is an Asus P5Q deluxe). Specs give 2.83GHz, OC'ed it to 3.40 GHZ without any problem (or so I thought) till 2 months ago. Cooling is provided by stock Intel Fan... 2 Months ago, I began to see random crashes, bios saying CPU overheat error... PC would reboot at OC'ed speed without any problem. Since last saturday and a few more crashes, PC won't reboot at 3.40 GHz, and even at stock speed (2.83 GHz), I got core temperatures of (60 C idle, 95 C under load) on the first two cores. This is the 4 core temperatures I am talking about, not the T-CPU which obvioulsy is lower. Fan is running at a steady 2000 RPM. Questions for you : 1. Is 2000 RPM the normal speed of the Intel fan or is my fan somehow broken (which could explain the overheating). In this case, any recommendation for a good fan for OCing ? 2. Hypothesis I fear is the right one: can the CPU have been slowly damaged over time by this OCing, meaning there is nothing much to do except waiting for it to die ? (As a side note, I am surprised that the 9550 is still around 300 $CDN here... Thought it would have been cheaper with all those i3/i5/i7 around). Any help or advice would be more than welcome...

  Read the article

• sharing a folder between linux and windows over the internet

  - by valya

  Hello Currently my job is to make websites with Django. I use many things like virtualenv, PIL, etc. The problem is, I can't stand Linux on my desktop. I like it on servers, It's greate to use it over the SSH. But for desktop? No way. But for the development Linux is quite essential. Of course almost everything is ported to Windows, but it's not as simple to use as in Linux. For example, Windows shell is awful in comparison with Linux. So I've tried Cygwin, but it's too damn slow. Every time django dev server reloads, it tooks almost 20-30 seconds. In comparison, then using "native" python on Windows or Linux, it reloads instantly. Even worse, Cygwin makes all my system very slow. I've been thinking about it and have thought up a way to go. I can share a folder with my application with some Linux box. The devserver and everything will run on that box, while I'll be happy editing files and running the browser on my Windows 7. SSH shell is much quickier and handy than Cygwin. Currently there are no Linux boxes in my home network (except for my android phone :) but I have several VDS boxes with Debian. So, how do I share a Windows folder with VDS box? I can't rely on my desktop IP but I can rely on the VDS's one. I need sharing to be as quick as possible (well, 2-3 seconds ping is OK) and "native" for both systems, so I could use a folder like a normal folder in both Windows and Linux.

  Read the article

• PHP memory_limit local value does not match php.ini value

  - by Buttle Butkus

  CentOS system. Summary: changed memory_limit in master and local php.ini and yet no change in the local value for a particular virtual host. Trying to improve performance, I set the memory_limit to 1024M in /etc/php.ini phpinfo() shows Master and Local values for other virtual hosts on the server as 1024M. Changing the value in /etc/php.ini changes all values, except one. One site is stuck with a local value of 256M. I thought I found the problem: there is a php.ini file (which I didn't know about) in that site's root, and it had memory_limit = 256M I changed it to 1024M. Problem solved? No. And now I don't know where to look. Obviously, I've restarted apache (/etc/init.d/httpd restart), and that usually does the trick. I also turned off APC cache, though I don't think it would cache ini files. And finally, I tried adding this to the virtual host in httpd.conf: php_value memory_limit 536870912 (yes, that would be 5 GB) And that had no effect whatsoever. What else could be the problem? Thanks.

  Read the article

• How can I restore "Open With" context menu item in Windows 7?

  - by Izzy Helianthus

  I tried various way to fix this problem but ended up with a dead end. My problem would be the missing "Open With" context menu items (or subitems?). It did not appear even though I hovered it for a minutes or two. Below is a screenshot of the respective right-click menu. Note: The only problem with "Open With" is at the right-click menu (as well as FILE menu). Edited: The "Open With" context submenu that only accessible at the top, while the typical right click menu doesn't work. Repaste from Comment. I don't think it's involved with any windows files because other user in the same computer doesn't affected at all. I can see the "Open With" context submenu. I believe this must have involved with current user's registry. It happens to all files (any file types, except folder). I can only use Open With by clicking at the file and select it manually at the top of Explorer window. (Refer to the link for the screenshot)

  Read the article

• HAproxy with MySQL Master-Master Replication incredibly slow

  - by Yayap

  I have two MySQL servers in multi-master mode, with an HAproxy machine for simple load balancing/redundancy. When I am connected to one of the servers directly and try to update about 100,000 entries, it is completed including replication in about half a minute. When connecting through the proxy it takes usually over three whole minutes. Is it normal to have that type of latency? Is something amiss with my proxy configuration (included below)? This is getting really frustrating as I assumed the proxy would do some sort of load balancing, or at least have little to no overhead. #--------------------------------------------------------------------- # Example configuration for a possible web application. See the # full configuration options online. # # http://haproxy.1wt.eu/download/1.4/doc/configuration.txt # #--------------------------------------------------------------------- #--------------------------------------------------------------------- # Global settings #--------------------------------------------------------------------- global # to have these messages end up in /var/log/haproxy.log you will # need to: # # 1) configure syslog to accept network log events. This is done # by adding the '-r' option to the SYSLOGD_OPTIONS in # /etc/sysconfig/syslog # # 2) configure local2 events to go to the /var/log/haproxy.log # file. A line like the following can be added to # /etc/sysconfig/syslog # # local2.* /var/log/haproxy.log # log 127.0.0.1 local2 # chroot /var/lib/haproxy # pidfile /var/run/haproxy.pid maxconn 4096 user haproxy group haproxy daemon #debug #quiet # turn on stats unix socket stats socket /var/lib/haproxy/stats #--------------------------------------------------------------------- # common defaults that all the 'listen' and 'backend' sections will # use if not designated in their block #--------------------------------------------------------------------- defaults mode tcp log global #option tcplog option dontlognull option tcp-smart-accept option tcp-smart-connect #option http-server-close #option forwardfor except 127.0.0.0/8 #option redispatch retries 3 #timeout http-request 10s #timeout queue 1m timeout connect 400 timeout client 500 timeout server 300 #timeout http-keep-alive 10s #timeout check 10s maxconn 2000 listen mysql-cluster 0.0.0.0:3306 mode tcp balance roundrobin option tcpka option httpchk server db01 192.168.15.118:3306 weight 1 inter 1s rise 1 fall 1 server db02 192.168.15.119:3306 weight 1 inter 1s rise 1 fall 1

  Read the article

• Verizon 4G LTE vs. a LAN

  - by n8wrl

  I have been having quite a bit of trouble getting my new Verizon 4G-LTE service running on a Windows 7 desktop. My desktop is on a LAN here at home with two other PC's. We all share printers, files, media, etc. Until yesterday, we also shared a Verizon 3G modem via a NetGear 3G broadband WAP. That isn't compatible with the 4G so now I am just trying to get the 4G modem working directly connected to one of the desktops. After some USB wrangling, it seems to work. Except, every 7-10 minutes the connection would drop. After some time on the phone with a very nice Verizon technician, it seems to be staying up - it's been up for 20 minutes now. He told me that my LAN was causing the 4G to drop. That traffic on my LAN, even though it is not destined for the internet (ICS not working yet) was causing the cell tower to detect an 'IP change' and a 'security violation' in my modem and drop my connection. Is this Verizon's way of forbidding more than one computer to share a modem? I have my computer running now without a LAN connection and the 4G is still up. But this isn't practical. Has anyone heard of this?

  Read the article

• Why can't I boot in to Windows Recovery Environment to fix my HDD or salvage my data?

  - by Kevin

  I've been trying to get in to WindowsRE to salvage the files on my Sony Vaio laptop after it failed to load Vista (it finally, consistently displays "Error loading operating system" after months of such intermittent failures, usually rectified via restarts or utilizing Startup Repair or CHKDSK from WindowsRE) . The problem is, after successfully accessing it once after this failure (and many times before over the course of the laptop's life), I can no longer get it to load. During the last successful access (right after the failure), I ran startup repair, which itself failed and notified me that the boot sector was corrupt. I attempted to head in to Sony's proprietary recovery tools menu, which is accessible from WindowsRE when it is loaded from the recovery partition or recovery disk, however it hung. I have since been unable to access the recovery environment after restarting, using any of these methods: Access via the recovery partition (pressing F10 on boot) Access via recovery DVD (created using the same computer when it was healthy) Access via a Windows Vista installation DVD All three methods produce the same results: The computer acknowledges the boot attempt The computer successfully gets passed the "Windows is loading files" screen The computer successfully gets passed the Windows loading screen The computer then stalls at a black screen, while showing HDD activity (via indicator light). After a few minutes, the HDD activity ceases, and after a few more minutes, the over sized cursor that is utilized in WindowsRE appears on the black screen. The actual recovery environment, however, never appears, even after leaving the computer in such a state overnight. What is fustrating is that other bootable utilities, such as SeaTools for DOS and MemTest, boot up and run fine. In running perfectly normally, MemTest was able to produce a plethora of errors utilizing my RAM. I'm inclined to believe the RAM's faultiness may causing the WindowsRE booting to fail. Would this be a valid assumption? If I'm not mistaken, booting from external media utilizes the RAM, so such a reason is plausible, assuming my knowledge of bootloading is correct. Other than that, I can't figure out any reason why all the bootable utilities except WindowsRE run fine. Does anyone know what the problem is, or could be? Any solutions?

  Read the article

• Problems with synaptic touchpad

  - by penlite

  The "enhanced" features of the synaptics touchpad (ie scroll, pinch zoom) on my windows 7 64 bit dell studio 17 only work intermittently. This was an issue with the original OEM driver and also with the new driver from synaptics - please do not suggest that i update, reinstall, install as administrator, check or jiggle the driver - if i hear that one more time i will freak out. I have researched this for days and appears to be a common problem without a solution (many suggestions to update the driver though -argh). Dell and synaptics have not been helpful. I have checked that syntpehn.exe and syntphelper.exe are running (sometimes the UAC seems to block syntpehn.exe from running at startup). When the touchpad fails i can still use it to control the pointer and access the synaptics settings although some of the options are disabled (greyed out or simply unresponsive). It is the only pointing device i have installed - i had a logitech trackball attached but have uninstalled all software and drivers (including hidden devices) as per synaptic. It is also the only device using IRQ 12. Any help would be greatly appreciated except "update the driver".

  Read the article

• How to calculate RAM value on performance per dollar spent

  - by Stucko

  Hi, I'm trying to make decisions on buying a new PC. I have most specifications (processor/graphic card/hard disk) pin-downed except for RAM. I am wondering what is the best RAM configuration for the amount of money I'm spending. As the question of best is subjective, I'd like to know how would I calculate the value of RAM sticks sold. 1.(sample)The value of amount of memory: 1) CORSAIR PC1333 D3 2GB = costs $80 2) CORSAIR PC1333 D3 4GB = costs $190 would it be better to buy 2 of item 1) instead of 1 of item 2) ?? Although I would normally choose to have 1 of 2) as the difference is only (190-(80*2)) = 30 as I would save 1 DIMM slot, What I need is the value per amount: 1) 80/ 2 = $40 per 1GB 2) 190/ 4 = $47.5 per 1GB 2. The value of frequency: 1) CORSAIR PC1333 4GB = costs 190 2) CORSAIR PC1600C7 4GB = costs 325 Im not even sure of the denominator ... $ per 1 ghz speed? 3. The value of latency: 1) CORSAIR CMP1600C8 8-8-8-24 2GBx3 (triple channel) = costs 589 2) CORSAIR CMP1600C7D 7-7-7-20 2GBx3 (triple channel) = costs 880 Im not even sure of the denominator ... $ per 1 ghz speed? Just for your information i'd like to get the best out of the money im going to spend to put on a 6 DIMM slot i7core motherboard.

  Read the article

• What parts of a motherboard age, and how can I choose one with the longest possible life?

  - by Robert Harvey

  I have a home-built computer that's probably about four years old. I realize this probably seems ancient to some folks, but computers have no moving parts (except the fans), so theoretically they should last a long time, if I still have software to run on them. A few weeks ago, it began blue-screening and freezing up, with various error messages. It almost always happened about five minutes after startup. I assumed that the video card was overheating, since the cheap little fan on the heatsink died, so I replaced it. Long story short, after upgrading the video drivers a couple of times and performing some other troubleshooting, I remembered that the last time this happened, I took out the memory SIMS and cleaned the contacts with a gum eraser, so I did that again (noting that the SATA cables were very close to the chips on the SIMS). I re-routed the cables and reinstalled the SIMS. So far, so good; the machine has been trouble-free since. But blue-screens are distressing; I never know what bits are being chewed up in my OS installation when something like this happens. So I'm wondering if I'm choosing my components properly. If it matters, it's an Intel D915GAG motherboard and Corsair memory, but what I'm wondering is, should I be looking for certain characteristics when I choose these parts for my next computer, so that I can avoid this problem in my next build?

  Read the article

• Mercurial internal Setup on Windows 7 - Exception happened during processing of request from ...

  - by Sad0w1nL1ght

  Hy, i have 1 central repository and many locals. On my machine i have local and a central repository too. I can make clone/commit/update/push/pull very easy between the local and central repository on my local machine. but when i want to make a clone from another machine it gets an error. listening at http://MyLocalMachine:8000/ (bound to *:8000) ---------------------------------------- Exception happened during processing of request from ('192.168.0.194', 49319) Traceback (most recent call last): File "SocketServer.pyc", line 558, in process_request_thread File "SocketServer.pyc", line 320, in finish_request File "mercurial\hgweb\server.pyc", line 47, in __init__ File "SocketServer.pyc", line 615, in __init__ File "BaseHTTPServer.pyc", line 329, in handle File "BaseHTTPServer.pyc", line 323, in handle_one_request File "mercurial\hgweb\server.pyc", line 79, in do_GET File "mercurial\hgweb\server.pyc", line 70, in do_POST File "mercurial\hgweb\server.pyc", line 63, in do_write File "mercurial\hgweb\server.pyc", line 127, in do_hgweb File "mercurial\hgweb\hgweb_mod.pyc", line 86, in __call__ File "mercurial\hgweb\hgweb_mod.pyc", line 118, in run_wsgi ErrorResponse ---------------------------------------- The command line wich started the central repo: hg serve -R TT -n TTZoli The command from remote machine for cloning: hg clone --pull http://MyLocalMachine:8000/TT Config for the central repo: [ui] username = MyLocalUserName username = test <[email protected]> with this user i'm trying to acces the central repo [web] push_ssl = false Config for the remote repo: [ui] username = test <[email protected]> [web] push_ssl = false I'm not sure if it's relevant,my firewall is turned off on both machines, and the files in /hg folder are not versioned on the server, except hgignore. Could you please suggest some ideas? What could be the problem? Thanks in advance!

  Read the article

• Merge changes in Microsoft Word documents

  - by Álvaro G. Vicario

  I'm using Microsoft Word 2002 to maintain some documentation. The documents are stored in a version control repository (Subversion) together with the source code it documents. My Subversion client (TortoiseSVN) comes with a little VBA script that allows to leverage the built-in revisions feature when merging different branches. In other words, when I want to copy changes from one document to another, Word compares both documents (source and target) and builds a third document that has the contents of the source doc tagged as revisions, so I can then review differences one by one and confirm or discard changes. While this is handy, it also means that making a single change to the source document forces me to review all the differences between both documents and discard all of them except the only actual change. My questions is... Do you know about an application or plug-in that's able to find the differences between two Word documents and apply those differences to a third document? (I know 2002 is very old but that's what my company gives me; I'm open to solutions that use newer versions though.)

  Read the article

• Why is my filesystem being mounted read-only in linux?

  - by Tim

  I am trying to set up a small linux system based on Gentoo on a VirtualBox machine, as a step towards deploying the same system onto a low-spec Single Board Computer. For some reason, my filesystem is being mounted read-only. In my /etc/fstab, I have: /dev/sda1 / ext3 defaults 0 0 none /proc proc defaults 0 0 none /sys sysfs defaults 0 0 none /dev/shm tmpfs defaults 0 0 However, once booted /proc/mounts shows rootfs / rootfs rw 0 0 /dev/root / ext3 ro,relatime,errors=continue,barrier=0,data=writeback 0 0 proc /proc proc rw,nosuid,nodev,noexec,relatime 0 0 sysfs /sys sysfs rw,nosuid,nodev,noexec,relatime 0 0 udev /dev tmpfs rw,nosuid,relatime,size=10240k,mode=755 0 0 devpts /dev/pts devpts rw,nosuid,noexec,relatime,gid=5,mode=620 0 0 none /dev/shm tmpfs rw,relatime 0 0 usbfs /proc/bus/usb usbfs rw,nosuid,noexec,relatime,devgid=85,devmode=664 0 0 binfmt_misc /proc/sys/fs/binfmt_misc binfmt_misc rw,nosuid,nodev,noexec,relatime 0 0 (the above may contain errors: there's no practical way to copy and paste) The partition at /dev/hda1 is clearly being mounted OK, since I can read all the data, but it's not being mounted as described in fstab. How might I go about diagnosing / resolving this? Edit: I can remount with mount -o remount,rw / and it works as expected, except that /proc/mounts reports /dev/root mounted at / rather than /dev/sda1 as I'd expect. If I try to remount with mount -a I get mount: none already mounted or /sys busy mount: according to mtab, sysfs is already mounted on /sys Edit 2: I resolved the problem with mount -a (the same error was occuring during startup, it turned out) by changing the sysfs and proc lines to proc /proc proc [...] sysfs /sys sysfs [...] Now mount -a doesn't complain, but it doesn't result in a read-write root partition. mount -o remount / does cause the root partition to be remounted, however.

  Read the article

• Linksys wireless router will not hardware reset.

  - by Jack M.

  Hello, all. I'm unable to make my router perform a hardware reset, and I cannot understand why. All was working well, except that my iPhone could not connect to the wireless. I found that the router was only allowing AES encryption on WPA2 Personal mode, so I upgraded the firmware. I updated the firmware to Ver.1.06.1, and everything went screwy. The router is no longer showing up in the WiFi list (as Linksys, or its previous network name). Wiring into the router gives me an IP address from my ISP (24.121.121.XXX). Attempting to do a hardware reset, but the power light never starts flashing and the router does not seem to reboot. My machine wired in is still online with no interruption in WoW. Pulling the power cord to force a reset returns it to the same state. I even went so far as to pull up my previous IP address (from DynDNS) and try to connect to that, but it wont even ping. What I'm trying to find out is: Did the new firmware fry the thing, or is there some way to fix this? Thanks in advance for any help.

  Read the article

• VirtualBox: Can't get Bridged Networking to work (Win7 host)

  - by MikeTheTall

  I'm trying to set up a virtual LAMP server, including sharing files between the guest OS (Ubuntu Server) and the host OS (Windows 7) using samba. I think my problem is that I can't get Bridged (or Host-Only) networking to work in VirtualBox. I can boot the Linux VM just fine with NAT, but then can't access any services on it directly (except after port-forwarding port 80)(my understanding is that port-forwarding works because I'm not running a web server on the host OS, and therefore it can forward traffic to the unused port 80). I don't think that port-forwarding samba traffic (from the host to the guest) will work since I think that the host OS is using those ports. When I turn off NAT and turn bridged networking on I get an error. The VM fails to boot, with a dialog popping up (title: VirtualBox - Error) that says "Failed to open a session for the virtual machine UbuntuServer. Configuration error: Failed to get MAC address (VERR_CFGM_VALUE_NOT_FOUND). I'm hoping that once this is resolved then samba will work ok :) Any advice on this would be great (how to fix it would be wonderful, next steps for troubleshooting would be great, too :) )

  Read the article

• Parsing text files

  - by d03boy

  I encountered a situation tonight where I wanted to parse a text file. I had a very, very long word list that contained English words delimited by lines. I wanted to get rid of every word (or line) that was longer than 7 characters. This would be simple in Linux but I can't seem to find a simple solution in WindowsXP. I tried using Notepad++ regular expression search but that was a huge failure. I tried using the expression .{6,} without finding any matches. I'm really at a loss because I thought this sort of thing would be extremely easy and there would be tons of tools to accomplish a task like this. It seems like Notepad++ supports every other feature in the world except the very basic ones that seem the most obvious. Another one of my goals was to put some code before and after the word on each line. aardvark apple azolio would turn into INSERT INTO Words (word) VALUES ('aardvark'); INSERT INTO Words (word) VALUES ('apple'); INSERT INTO Words (word) VALUES ('azolio'); What suggestions/tools/tips do you have to accomplish tasks similar to this in WindowsXP?

  Read the article

• certificate working on IP but not on URL

  - by Stephan

  I asked this question on stackoverflow, and I've been suggested to repost it here. I have a problem accessing my site (on https) with IEMobile 9 (WP 7.5). It says it's got problem with the certificate, as if it wasn't valid. Everything works on any other browser or platform I tested (android (several phones and a galaxy tab with stock browser, firefox, opera, dolphin), iOS (iphone and ipad with safari and chrome), an old nokia with symbian, windows 7, linux and mac). To try to solve this I saved the certificate (.cer) on the server and accessed it from the phone browser. It always complained except when I accessed it through the server IP (192.168.xx.xx). At that point it (said it) installed correctly the certificate. If then I try to access the index.html still using the IP all works fine and it doesn't complain about the certificate. If, though, I try to access the index using the actual URL (blah.myblah.com), it complains again about the certificate, as if it wasn't installed! It isn't a problem of DNS, cause that's up and serving the right ip, and the phone is correctly setup to use it. The certificate is signed by geotrust/rapidssl for *.myblah.com.

  Read the article

< Previous Page | 197 198 199 200 201 202 203 204 205 206 207 208  | Next Page >