Search Results

Search found 7850 results on 314 pages for 'except'.

Page 200/314 | < Previous Page | 196 197 198 199 200 201 202 203 204 205 206 207  | Next Page >

  • 2nd instance of mysql closes/doesnt start no warnings/errors?

    - by acidzombie24
    I have an external HD and i'd like to run a 2nd mysql instance on it. I used the windows installer to install/configure mysqld as a service on windows7. I took the my.ini from C:\Program Files\MySQL\MySQL Server 5.5\my.ini Then edited the port (client and mysqld), datadir and innodb_data_home_dir. After running this command "C:\Program Files\MySQL\MySQL Server 5.5\bin\mysqld" --defaults-file="f:/dev/my.ini" I found an error which was all about the innodb_data_home_dir directory not existing. After that I ran the command again. Mysqld simply starts up for a second then immediately closes. I see no message in my command prompt. I know this command line args are correct as i see the mysqld service using the same one except a different my.ini path. Also it did tell me about the directory not existing so i know it is reading the new ini file. How do i figure out why this 2nd instance of mysqld is closing? How do i get 2 instance running? I'm using v 5.5

    Read the article

  • OpenSwan (IPSEC) on Fedora 13 with Snow Leopard as a client

    - by sicn
    I recently installed OpenSwan on my Fedora 13 machine. I want to use it to connect with Mac OS X with L2TP over IPSEC, unfortunately I am already stuck on the IPSEC-negotation part. My server is running behind a NATted firewall so my external IP differs from the server's IP. The server has a fixed IP on the network and the same is almost always valid for the clients (they are usually behind a NATted firewall). I installed OpenSwan on Fedora 13 and have following configuration: config setup protostack=netkey nat_traversal=yes virtual_private=%v4:10.0.0.0/8,%v4:192.168.0.0/16,%v4:172.16.0.0/12 oe=off nhelpers=0 conn L2TP-PSK-NAT rightsubnet=vhost:%priv also=L2TP-PSK-noNAT conn L2TP-PSK-noNAT authby=secret pfs=no auto=add keyingtries=3 rekey=no ikelifetime=8h keylife=1h type=transport left=my.servers.external.ip leftprotoport=17/1701 right=%any rightprotoport=17/0 IPSEC starts fine and listens to UDP 500 and 4500. These two ports are opened in the firewall and are forwarded fine to the server. In my /etc/ipsec.secrets file I have my.servers.external.ip %any: "LongAndDifficultPassword" And finally in my sysctl.conf (the redirect-entries are there because OpenSwan was strongly protesting about send/accept_redirects being active) I have net.ipv4.ip_forward = 1 net.ipv4.conf.all.send_redirects = 0 net.ipv4.conf.all.accept_redirects = 0 Running "ipsec verify" gives me "all greens" (except Opportunistic Encryption Support, which is DISABLED), however, when trying to connect my Mac gives me following in the logs: Nov 1 19:30:28 macbook pppd[4904]: pppd 2.4.2 (Apple version 412.3) started by user, uid 1011 Nov 1 19:30:28 macbook pppd[4904]: L2TP connecting to server 'my.servers.ip.address' (my.servers.ip.address)... Nov 1 19:30:28 macbook pppd[4904]: IPSec connection started Nov 1 19:30:28 macbook racoon[4905]: Connecting. Nov 1 19:30:28 macbook racoon[4905]: IKE Packet: transmit success. (Initiator, Main-Mode message 1). Nov 1 19:30:31 macbook racoon[4905]: IKE Packet: transmit success. (Phase1 Retransmit). Nov 1 19:30:38: --- last message repeated 2 times --- Nov 1 19:30:38 macbook pppd[4904]: IPSec connection failed Any ideas at all?

    Read the article

  • why is rdiff-backup not compatible with encfs ---reverse

    - by user330273
    I'm trying to use encfs with rdiff-backup to ensure that my backups to a remote server are encrypted. The easiest way to do this would be to use encfs --reverse - which means encfs will create a virtual encrypted file system, which I can then backup using rdiff-backup. Except that it doesn't work. Rdiff-backup fails every time with an "input/output error" on the encfs virtual filesystem. It seems I'm not the only one with this problem, but no one has said what the problem is: this person reported the same issue, but was just told to use sshfs instead (see below on that); in this question on serverfault, one of the answers just states that "rdiff-backup seems to have trouble accessing the EncFS-reverse filesystem." There's an open bug report on the Debian bug tracker(bug 731413, I can't post the link) on this bug, but it's been open since December 2013 with no response. Does anyone know what the problem actually is? Is there a workaround? I can't use the two most commonly suggested alternatives - sshfs and then running encfs on that, or using Duplicity - as both require a much higher bandwidth connection than I have access to (Duplicity requires regular full backups).

    Read the article

  • Error 550 Mail Relay Message Could Not Be Sent

    - by mraliks
    I'm not sure if this is the right area to ask, but here we go. I have a client who has a couple websites on a Windows server with MailEnable as the mail manager. Any emails being sent from the server work great, except when sending to some domains, the message does not go through due to the following error: 12/13/11 01:15:56 ME-I0026: [86476200E5834227A819E6E63E0EFDA2.MAI] Sending message 12/13/11 01:15:57 ME-IXXXX: [86476200E5834227A819E6E63E0EFDA2.MAI] Remote server returned a response indicating a permanent error. Server Response: (550 Relaying not allowed**) 12/13/11 01:15:57 ME-E0036: [86476200E5834227A819E6E63E0EFDA2.MAI] MAIL FROM command Failed. Can anyone give me some leads on how to correct the settings to allow emails to go through properly? In particular, the emails are not going through to a Network Solutions email account and Network Solutions has not been very helpful thus far. In addition, can a domain's DNS settings affect this error? Currently, the domains are hosted by Network Solutions and use the Network Solutions email service to send/receive email. The server is located with a different company and the Domains' DNS points to it. Which mail related DNS entries are allowed or not allowed in this scenario? Thanks

    Read the article

  • Acer recovering windows vista

    - by Charlie Pigarelli
    My computer history is very long even of my computer has 4 years of life. An year ago I installed Windows 7 on this acer m1610 that had Vista before. My technic left me 2 recovery disc for "acer vista" before updating it to Windows 7. Then the computer had some trouble. The graphic card broke and we decided to use another computer. Yesterday I had the great idea to fuse the two computer to have a better one... So I moved the graphic card of the latter computer to the acer and everything gone well. Then the trouble of speed, it had before, come back. So I decided to reinstall the very first Windows: Vista back again. I booted the computer with those 2 DVD-R my technic left me and at the end of the process it asked me to insert "the backup cd number one or the system disk". I found 2 original Acer "Blank Recovery Disc" DVD-R and tried with those: rejected. Tried with empty DVD-+R: rejected. I tried with CDs: rejected. I don't have any system disc with me. Except for those 2 DVD-R my technic left me. What am I supposed to do now? I even tried with these fantomatic alt+f9/f10 that should start the recovery without any disc... But nothing happened. PS: the installation cannot complete if I do not insert the right disk. (The recovery disc uses Acer eRecovery Management as recovery software.

    Read the article

  • sysctl.conf not running on boot

    - by Brian
    At what point is sysctl.conf supposed to be read during boot, and why might it not be running? I have the following settings which are not being applied when I reboot: net.bridge.bridge-nf-call-arptables = 0 net.bridge.bridge-nf-call-ip6tables = 0 net.bridge.bridge-nf-call-iptables = 0 net.bridge.bridge-nf-filter-pppoe-tagged = 0 net.bridge.bridge-nf-filter-vlan-tagged = 0 fs.nfs.nlm_udpport = 32768 fs.nfs.nlm_tcpport = 32768 The first section is needed for KVM bridging, and the second is to run the NFS lock manager on a known port. However, after booting, these values have not taken effect. If I run sysctl -p, then they do. This wouldn't be a huge issue, except that I can't figure out how to restart the lock manager without rebooting. I would really like to know why sysctl.conf isn't working at boot, but I'd settle for just being able to restart the lock manager. This is on Ubuntu server 10.04.2, kernel 2.6.32-31-server. I know some daemons check the permissions on their config files and refuse to work if they're too permissive, but sysctl.conf is 644 root:root, which I'm pretty sure is the default.

    Read the article

  • Use Mac OS X Server As Development Environment

    - by macinjosh
    I've installed Mac OS X Server 10.6.3 on my laptop to use as my normal OS. I do a lot of web development and thought it would be handy to run OS X Server so I could more easily manage my local development environment (Apache Virtual Hosts, Hostnames for each local site, etc). I'm really enjoying the new setup except for one problem. DNS. My ideal situation would be to add a site (some-site.local) in the Web Service and then go to the DNS Service and add a primary record for the new site. I actually got this working at one point but after a reboot it stopped working! The records look the same as they did before the reboot but the site doesn't come up in Safari. Here is a list of my needs: Need to be able to add new domains at a whim Domains always map to a site on the same box's Web Service Local & External IPs often change It would nice if it worked on any network (i.e. WiFi at the airport or coffee shop) Sites only need to be accessible locally Configuration should stay put even after rebooting I've done some googling and used this as a bit of guide. In the past I've used MAMP and then just a local Apache/PHP/MySQL install with a manually managed hosts file. I'd rather not go back.

    Read the article

  • Exchange 2010: Find Move Request Log after move request completes

    - by gravyface
    EDIT: significantly changed my question here to streamline it a bit. I've gone ahead and used 100 as my corrupted item count and ran it from the Exchange Shell. So the trail of tears continues with my SBS 2003 to 2011 migration: all the mailboxes have moved mailbox store from OLDSERVER to NEWSERVER, with the Local Move Requests completing successfully, except for one. What I'd like to do now is review the previous move request log files: when they were in progress, I could right-click Properties Log View Log File, but now that they're completed, that's not available. Nor can I use: Get-MoveRequestStatistics <user> -includereport | fl MoveReport ...as the move request has now completed and it errors out with "couldn't find a move request that corresponds...". Basically what I'd like to do is present the list of baditems to the user so that they're aware of what items didn't come across and if anything important was lost, be able to check their current OST, an archive.pst, etc. to recover it if possible. If this all needs to be wrapped up in a batch Exchange power shell command to pipe the output to log files on disk somewhere, I'm all ears, and would appreciate it for the next migration we do.

    Read the article

  • Internet Connection not working - USB LAN connection - from particular modem

    - by Paul
    I am trying to fix Internet connection on a friends Dell inspiron 1720 with XP service pack 3. It has an integrated network card that stopped working, after powering down/up the modem still didnt work I brought it back to my place to try a few things ie check cable, update driver etc... still didnt work. So I bought a USB LAN connector. It didnt work straight away but I went to configure the properties and changed the ConnectionType from AutoSense to 100 BaseT 10BaseT Full_Duplex, I basically just tried them all. From my place when connected to my desktop - 10 BaseT and 10BaseT Full_Duplex worked. From my place When connected to their laptop - 10 BaseT and 10BaseT Full_Duplex worked. Happy I went back to my friends house confident it would all work, and it didnt. Brought it back to mine and it did. While there, in Network Connections the connection is there recognized, enabled, 'working properly' it just says not connected. Also there is no led on the USB connector While at mine as above except there is an led on the USB connector and it says connected. Other difference I can think of is they have a cable modem, I'm plugged into the back of a Belkin wireless router - would this make a difference? Any other ideas what to try? (Would getting the model of the cable modem help anyone?) The USB connector is "DM9601 USB to Fast Ethernet"

    Read the article

  • CMS/Wiki to use for a HTML5 video site

    - by Clinton Blackmore
    Greetings. I want to put up a website with instructive screencasts, and allow for people to add comments to them. I would like use the Video for Everybody technique, partly because I dislike Flash and because it helps in a small way to move the web forward [while being backwards compatable]. I recognize that HTML5 is still in draft, and that support for it varies. I do have some hosting space, and can run Perl, PHP, and Ruby on Rails applications, with a MySQL backend. I should mention that part of my working job involves running some web servers, and that I am a programmer by training (with only a limited familiarity with Perl and PHP, and none with Ruby). I should mention why I don't particularly want to go with a video hosting site (like YouTube or Vimeo): Flash Video Resolution and Quality [I'd like to put up 800x600 videos] Videos promote a club that is not stricly non-profit [ie. may fall afoul of Terms of Service] I'm already paying for web hosting, and free video hosting comes with time and bandwidth limits I don't want there to be two locations where you can comment on the video Now, having said all that, I'd be quite comfortable putting up my own HTML pages, except: that's so web 1.0! :) [ie. it does not allow for comments] I also want to do some blogging and possibly put up a wiki; the site will not be entirely screencasts So, can anyone recommend a CMS (or Wiki, or similar application) that I can customise for this purpose?

    Read the article

  • How can I tell SELinux to give vsftpd write access in a specific directory?

    - by Arcturus
    Hello. I've set up vsftpd on my Fedora 12 server, and I'd like to have the following configuration. Each user should have access to: his home directory (/home/USER); the web directory I created for him (/web/USER). To achieve this, I first configured vsftpd to chroot each user to his home directory. Then, I created /web/USER with the correct permissions, and used mount --bind /web/USER /home/USER/Web so that the user may have access to /web/USER through /home/USER/Web. I also turned on the SELinux boolean ftp_home_dir so that vsftpd is allowed to write in users' home directories. This works very well, except that when a user tries to upload or rename a file in /home/USER/Web, SELinux forbids it because the change must also be done to /web/USER, and SELinux doesn't give vsftpd permission to write anything to that directory. I know that I could solve the problem by turning on the SELinux boolean allow_ftpd_full_access, or ftpd_disable_trans. I also tried to use audit2allow to generate a policy, but what it does is generate a policy that gives ftpd write access to directories of type public_content_t; this is equivalent to turning on allow_ftpd_full_access, if I understood it correctly. I'd like to know if it's possible to configure SELinux to allow FTP write access to the specific directory /web/USER and its contents, instead of disabling SELinux's FTP controls entirely.

    Read the article

  • SCCM 2012 Clients no longer detecting

    - by user3685428
    Here is the scenario I had a fully functioning SCCM 2012 site server with the DP, MP, SUP, Application catalog, etc. roles configured and working. There is only one server on this site. Everything was great but i was not happy with SUP, so i decided to create a separate WSUS server and configure Windows Updates through GPOs. That setup worked great as well so i went ahead and removed the SUP role from SCCM and removed the WSUS feature from my SCCM server (they were configured on the same SCCM Server). I did not notice any problems right away. A couple days later i noticed that the OSD deployments were giving errors, and after a couple hours of trying suggestions from Google, i was able to uninstall PXE and make a few changes and reinstall with WDS to get it working again. Again, thought everything was fine and continued on. The last couple days i have noticed that any new machine deployed or installing the Client will show in the SCCM console as "No" Client. The client machines will show connected to a site but the software center shows "IT Organization" instead of our site like the previous clients. The existing clients all seem to be functioning normally. they still receive application distributions and configuration baselines, etc. Reinstalling, uninstalling and reinstalling, repairing does not fix the problems and this happens on all new clients. ClientLocation.log shows it connecting to the correct MP. Nothing odd in any of the logs except for the ClientMessaging.log which repeats continuously this line: <![LOG[Raising event: instance of CCM_CcmHttp_Status { ClientID = "GUID:0450fde3-ab82-41bf-9c33-87a18113744b"; DateTime = "20140528214824.993000+000"; HostName = "SOUNDWAVE.domain.org"; HRESULT = "0x00000000"; ProcessID = 4092; StatusCode = 0; ThreadID = 3720; }; ]LOG]!><time="16:48:24.994+300" date="05-28-2014" component="CcmMessaging" context="" type="1" thread="3720" file="event.cpp:706"> thanks

    Read the article

  • Cisco Catalyst 4500 Policy Based Routing

    - by Logan
    In order to test a new firewall I just set up I'm trying to implement policy based routing on our core switch. I want traffic from certain vlans to be routed to the new firewall while everything else continues being routed through the old firewall. I was trying to use this guide. Everything from that guide works fine except trying to run the "ip policy route-map" command in the interface configuration mode. IOS is telling me that such a command doesn't exist. A "show ip interface vlan" command says that policy routing is disabled. Any ideas? Output of "show ver": Cisco IOS Software, Catalyst 4500 L3 Switch Software (cat4500-IPBASEK9-M), Version 12.2(53)SG, RELEASE SOFTWARE (fc3) Technical Support: http://www.cisco.com/techsupport Copyright (c) 1986-2009 by Cisco Systems, Inc. Compiled Thu 16-Jul-09 19:49 by prod_rel_team Image text-base: 0x10000000, data-base: 0x11D1E3CC ROM: 12.2(31r)SG2 Dagobah Revision 226, Swamp Revision 34 RTTMCB2223-1 uptime is 3 years, 22 weeks, 2 days, 19 hours, 28 minutes Uptime for this control processor is 51 weeks, 2 days, 18 hours, 2 minutes System returned to ROM by power-on System restarted at 19:22:02 UTC Tue Jul 12 2011 System image file is "bootflash:cat4500-ipbasek9-mz.122-53.sg.bin" ... cisco WS-C4510R (MPC8245) processor (revision 4) with 524288K bytes of memory. Processor board ID FOX103703W3 MPC8245 CPU at 400Mhz, Supervisor V Last reset from PowerUp 42 Virtual Ethernet interfaces 244 Gigabit Ethernet interfaces 511K bytes of non-volatile configuration memory. Configuration register is 0x2

    Read the article

  • PC powers off at random times

    - by Timo Huovinen
    Short Version After experiencing some problems with Mobo batteries my PC started to power off at random times, the power off is instant and sudden and does not restart afterwards, need help figuring out the cause. Facts: Powers off when PC is playing games Powers off when PC is idle Powers off when PC is in safe mode Powers off when PC is in BIOS Powers off when PC is booted through a Windows installation USB Replaced the motherboard battery several times Replaced the 650W PSU with a 750W PSU Replaced the RAM Swapped the RAM between slots Re-applied thermal paste to the CPU Checked if the motherboard touches the case Nothing is overclocked PC Specs PC specs: OS: Windows 7 Ultimate SP1 RAM: klingston 1333MHz 4GB stick CPU: AMD Phenom II x4 955 Mobo: Gigabyte 88GMA-UD2H rev 2.2 Motherboard battery: CR2032 3v HDD: 500GB Seagate ST3500418AS ATA Device Graphics: ATI/AMD Radeon HD 6870 Very Long version Around 10 months ago I built a brand new gaming PC. Around 6 months ago it's time setting in windows started resetting to the year 2010. I swapped the Motherboard battery for a new one of the exact same size and shape and voltage, and the problems disappeared...for around 2 weeks. Then the same problem happened again, time gets reset, I swapped the battery again, and the problem was gone for good and everything was great for about 3 months.. then another problem started happening, the PC started to power off suddenly and without warning at completely random times, sometimes the PC works for and hour, sometimes 5 minutes. So I read on the forums that it might be either the PSU or the motherboard Battery or RAM or HDD or the Graphics card or the CPU or the motherboard or the drivers or a Virus or Grounding issues, or something short circuiting, basically it can be anything... I spent some days researching, and decided to remove the possibility of a virus. I reset the CMOS, cleared all BIOS settings and reinstalled windows 7 after a full format of the HDD, but the random power off kept happening. I then disabled the restart on error option in windows and looked at the event log for error events, but they did not help me figure out the problem. Network list service depends on network location awareness the dependency group failed to start Source Kernel Power Event 41 Task Category 63 Source Disk Event ID 11 Task Category None The driver detected a controller error on device disk I took apart the PC, every little piece, re-applied some expensive thermal paste to the CPU, and double checked that none of the pieces are touching the PC case. The problem was gone, the PC no longer powered off randomly I re-attached the graphics card and all was good for 4 months... then the power off problem appeared again, but was happening at high intervals, the PC would shutdown once in 2 days on average, at random points in time, sometimes when it's idle all day long, sometimes when it's running CRYSIS 2. I checked the CPU temperature, because I know that AMD CPU's have a built in protection mechanism that switches off the PC if the CPU gets too hot, and the Temp was 50C system temp, and 45C CPU after running the PC all day long (I did not do tests to see if there are any temperature spikes, don't know how to do them) Originally the PSU that powered the PC was 650Watts and had one 4 pin cable to power the CPU, I replaced it with a new 750Watts PSU which has two 4 pin cables for the CPU, but the problem remained. I removed the graphics card and let the motherboard use the built in one, but the PC kept suddenly powering off at random times. I took apart the PC completely again, and re-applied thermal paste to the CPU, added lots of insulation, and checked for any type of short-circuit possibility again and again, but the problem remained. The problem was like that for some months. I replaced the Battery a couple of times over the time, changed lots of options in windows, and tried everything I could, but it kept powering off, so I stopped using the PC as much as I used to, just living with the random power offs from time to time, until a couple of days ago, when the power off happens almost immediately after powering on the PC. I replaced the RAM with a brand new one, but that did not help. Took apart the PC again, checked for anything anywhere that might cause it, found some small scratches on the very edge of the motherboard to the left of the PCI express x16 slot. This might cause the problem, I thought, but the scratch looks very superficial, not deep at all, and if the scratch did harm the motherboard, wouldn't it cause it to not start at all? And why did it start to power off a while ago, and then suddenly stop powering off? The scratches could not have vanished??? did chkdsk \d but it powered off when it was at 75% I removed the hard disks, the graphics card, while I fiddled with the BIOS settings, and suddenly the PC shut down while I was looking at the BIOS version. This makes me realize, it is not caused by: HDD, Windows, Drivers or the Graphics card I cleared the CMOS again, updated the BIOS from F5 to F6f beta, but that did not help, it might even seem that the PC powers off even sooner. The shutdown even happened to me while I booted through a windows 7 installation USB and was in the repair console. I removed one of the cables powering the CPU, now only one 4pin cable powers it, and it worked for 30mins after doing that, which makes me think that it's the CPU overheating, and because it gets less power, it overheats slower? The things that I am still considering: CPU overheating (does not seem to overheat, maybe false readings?) Motherboard short circuiting (faulty motherboard?) I desperately need some advice in what is faulty, is it a faulty Motherboard or an overheating CPU? or maybe something else? I have been breaking my head over this problem over a span of 6 months. I'm not sure if this is a good place to ask this question, if it is not, then tell me where I can get some experienced help. More info I have also discovered a mysterious piece that seems to have fallen out of the motherboard i119.photobucket.com/albums/o126/yurikolovsky/strangepiece.jpg What is it? Looks like each time that it powers off the datetime gets reset I also found another forum post tomshardware.co.uk/forum/… except I don't have Integrated PeripheralsUSB Keyboard Function option in BIOS :S Comments summary (asked by Random moderator) Q. tell me, if the computer restarts, is it immediately? Does it take a second and then restarts? Do you see (BSOD) or hear (PSU, short circuit) any suspicious when it happens? After reading trough it, it remains the mainboard that is faulty. – JohannesM A. Immediate power off, all the fans stop instantly, all the light turn off instantly, no sound or anything, and it remains off until I turn it back on. Thanks for the feedback, faulty motherboard is what I fear. Q. Try stress-testing the system with Prime95 and see if errors or shutdowns occur when the CPU is under full load. – speakr A. Prime95 heat stress test peaked CPU heat at 60C after 5mins, it powered off after 30mins of testing in the middle of the test with no errors, Prime95 Heat test or the stress-testing with low RAM usage (small or in-place FFTs) do not report errors while testing for 10-60 mins. The power off does not seem like it is affected by Prime95 at all Makes me wonder if it's a CPU or Motherboard issue at all. Q. I had similar random/intermittent problems with my old board. It gave one of a few different symptoms: keyboard and/or mouse would die and/or the RAM wouldn't work and/or it would shut down. It was in bad shape. One problems was that my old PSU had literally burned the connector on it (browned around the pins), another was that a broken lead inside the layers of the PCB would work sometimes if it happened to be hot or if I bent the board—by jamming a hunk of wood behind it. I managed to keep the board alive for several years, but eventually nothing I did would make it work correctly anymore. – Synetech A. I will try that as the last resort, ok? ;) Q. Have you tried a different power cord, surge protector, outlet (on a different circuit). It's worth a shot just to ensure it's not subpar wiring or a week circuit (dips in power may cause shutdown if the PSU can't pull enough juice from the wall). – Kyle A. yes, I attached the PC to an entirely different outlet on a different circuit and the problem persists. After connecting it to a different outlet after starting the PC it gave me 3 long beeps and 1 short one, then the PC immediately proceeded to boot up normally. Q. Re-check your mainboard manual and all PSU connections to your mainboard to be sure that nothing is missing (e.g. 12V ATX 4-pin/6-pin connector). If you can provoke shutdowns with Prime95, then consider buying new hardware -- a stable system should run Prime95 for 24h without any errors. Prime95 mentions errors in the log when they occur and gives a summary after the stress test was stopped manually (e.g. "0 errors, 0 warnings", if all is fine) – speakr A. Re-checked, there are no more PSU connectors that I can physically connect, except the one ATX 4-pin (there are 2 that power the CPU) that I disconnected on purpose, I have reconnected it but the problem persists. Q. With one PC I had a short curcuit. The power button on the front plate had its cables soldered, but not isolated, and the contacts were very close to the metal case. A heavier touch was enough to cause a shutdown. The PC's vibration could be enough – ott-- A. yes, it seems to switch off with even the lightest touch, I switched on the PC, then pulled out the front panel power cable that connects to the motherboard so the power button does not work anymore, after 5 mins of working like that, with the power button completely disconnected, just sitting idle, the PC powered off again, I don't think it's the power button. Q. I wonder if you dare to operate components without the case, that is remove motherboard, power, disk ( just put the motherboard on a wooden desk). Don't bend the adapters when running like that. – ott-- A. yes, I do dare to do that, but only tomorrow, too tired/late right now.

    Read the article

  • MySQL problem with many concurrent connections

    - by user48303
    Hi, here's a sixcore with 32 GB RAM. I've installed MySQL 5.1.47 (backport). Config is nearly standard, except max_connections, which is set to 2000. On the other hand there is PHP5.3/FastCGI on nginx. There is a very simple php application which should be served. NGINX can handle thousands of request parallel on this machine. This application accesses MySQL via mysqli. When using non-persistent connections in mysqli there is a problem when reaching 100 concurrent connections. [error] 14074#0: *296 FastCGI sent in stderr: "PHP Warning: mysqli::mysqli(): [2002] Resource temporarily unavailable (trying to connect via unix:///tmp/mysqld.sock) in /var/www/libs/db.php on line 7 I've no idea to solve this. Connecting via tcp to mysql is terrible slow. The interesting thing is, when using persistent connections (add 'p:' to hostname in mysqli) the first 5000-10000 thousand requests fail with the same error as above until max connections (from webserver, set to 1500) is reached. After the first requests MySQL keeps it 1500 open connections and all is fine, so that I can make my 1500 concurrent requests. Huh? Is it possible, that this is a problem with PHP FastCGI?

    Read the article

  • dns configuration error in plesk

    - by Karthik Malla
    I purchased a domain www.softmail.me at Godaddy.com and tried it DNS and getting lots of errors and finally change my nameservers to my server DNS i.e. NS101.VPSLAND.COM and NS202.VPSLAND.COM and created a domain in my plesk panel (Marked DNS & Mail required). After adding my domain to my plesk panel of my server I opened DNS records of that domain and found DNS records are automatically generated to my needs as following 65.75.241.26 / 24 PTR softmail.me. ftp.softmail.me. CNAME softmail.me. lists.softmail.me. CNAME softmail.me. mail.softmail.me. A 65.75.241.26 mssql.softmail.me. A 65.75.241.26 ns.softmail.me. A 65.75.241.26 sitebuilder.softmail.me. A 65.75.241.26 softmail.me. NS ns.softmail.me. softmail.me. A 65.75.241.26 softmail.me. MX (10) mail.softmail.me. webmail.softmail.me. A 65.75.241.26 www.softmail.me. CNAME softmail.me. Finally I waited for a week for I am unable to use my domain. Also in DNS lookup I cannot find any records to my Server except name servers of VPSland. Do I need to add VPSland namesevers anywhere in Plesk panel? If so where? Can anyone assist me where the mistake is?...

    Read the article

  • Virus / Malware: Explorer window with strange user logged into Hotmail

    - by abel
    I was looking into a PC, the user of which had complained that he couldn't connect to the internet and that the PC was experiencing random restarts. The PC runs WinXP SP3. On examination, I found that the Wireless Zero Configuration service was stopped. I enabled that and the internet was back on(The pc connected through wifi). Then I started firefox and browsed to gmail.com. I did not launch any other program, except for a few explorer windows. It was then I noticed a window had popped up(it was not a pop up). It had the explorer folder icon and instead of explorer folder contents, it showed a hotmail page, with a user named "Homer Stinson" logged in. The titlebar was empty and there were no toolbars. I asked the client whether this was his email id, which he said it was not. I opened task manager, which did not show this explorer window in it's Application tab. I switched back to the 'rogue' window and found that the hotmail settings page was now open, which later changed to the hotmail edit profile page for the same user. I was not clicking anything. Then suddenly the window closed. I checked the autorun locations, fired up a Malwarebytes Anti Malware scan which gave a clean result. The system also had an updated installation of AVG. I don't want a solution for this virus(?) problem. I asked this here because I wanted to know if somebody has come across something similar. What kind of malware can this be? The user had not seen a similar window before and I should have taken screenshots. (PS:Homer Stinson is an imaginary name. I searched for the other real name with some relevant keywords but could not come up with a virus/malware discussion post.) UPDATE: When I checked the PC later a DEP error had popped up closing which restarted the PC.

    Read the article

  • Running multiple sites on a LAMP with secure isolation

    - by David C.
    Hi everybody, I have been administering a few LAMP servers with 2-5 sites on each of them. These are basically owned by the same user/client so there are no security issues except from attacks through vulnerable deamons or scripts. I am builing my own server and would like to start hosting multiple sites. My first concern is... ISOLATION. How can I avoid that a c99 script could deface all the virtual hosts? Also, should I prevent that c99 to be able to write/read the other sites' directories? (It is easy to "cat" a config.php from another site and then get into the mysql database) My server is a VPS with 512M burstable to 1G. Among the free hosting managers, is there any small one which works for my VPS? (which maybe is compatible with the security approach I would like to have) Currently I am not planning to host over 10 sites but I would not accept that a client/hacker could navigate into unwanted directories or, worse, run malicious scripts. FTP management would be fine. I don't want to complicate things with SSH isolation. What is the best practice in this case? Basically, what do hosting companies do to sleep well? :) Thanks very much! David

    Read the article

  • Weird fluctuating time on a XEN linux guest

    - by Vin-G
    I have a weird problem with some servers here at work. We have a few XEN guests who's current time fluctuates. # date;date;date;date;date;date;date Thu Feb 25 16:00:40 PHT 2010 Thu Feb 25 16:00:48 PHT 2010 Thu Feb 25 16:00:40 PHT 2010 Thu Feb 25 16:00:48 PHT 2010 Thu Feb 25 16:00:40 PHT 2010 Thu Feb 25 16:00:48 PHT 2010 Thu Feb 25 16:00:40 PHT 2010 As seen above, the time fluctuates between 16:00:48 and 16:00:40, which is problematic for us since computing for time differences in some of our scripts becomes inaccurate (ex. what should be a few ms differences becomes some few second differences, and even sometimes, negative differences). The problematic servers are linux guests on a XEN host. The time fluctuates on the guest systems, but it is okay in the host itself. I've ruled out ntpd since this happens irregardless of whether ntpd is running or not on the guest systems. Guest is on full virtualisation. The time on both the host and the guest does match except that the time in the guest fluctuates at about a few seconds from the host's time, and the host time does not fluctuate. /proc/sys/xen/independent_wallclock is 0 in the host and does not exist in the guest. Ntpd service was stopped and disabled. Setting independent_wallclock to 1 in the host has no effect (that is, time still fluctuates in the guest). Though I was not able to restart the guest as it is a production server. Might be able to do that over the weekend. Any ideas on what to check and how to resolve this problem?

    Read the article

  • Issue with SSL using HAProxy and Nginx

    - by Ben Chiappetta
    I'm building a highly available site using a multiple HAProxy load balancers, Nginx web serves, and MySQL servers. The site needs to be able to survive load balancer or web servers nodes going offline without any interruption of service to visitors. Currently, I have two boxes running HAProxy sharing a virtual IP using keepalived, which forward to two web servers running Nginx, which then tie into two MySQL boxes using MySQL replication and sharing a virtual IP using heartbeat. Everything is working correctly except for SSL traffic over HAProxy. I'm running version 1.5 dev12 with openssl support compiled in. When I try to navigate to the virtual IP for haproxy over https, I get the message: The plain HTTP request was sent to HTTPS port. Here's my haproxy.cfg so far, which was mainly assembled from other posts: global log 127.0.0.1 local0 log 127.0.0.1 local1 notice # log 127.0.0.1 local0 user haproxy group haproxy daemon maxconn 20000 defaults log global option dontlognull balance leastconn clitimeout 60000 srvtimeout 60000 contimeout 5000 retries 3 option redispatch listen front bind :80 bind :443 ssl crt /etc/pki/tls/certs/cert.pem mode http option http-server-close option forwardfor reqadd X-Forwarded-Proto:\ https if { is_ssl } reqadd X-Proto:\ SSL if { is_ssl } server web01 192.168.25.34 check inter 1s server web02 192.168.25.32 check inter 1s stats enable stats uri /stats stats realm HAProxy\ Statistics stats auth admin:********* Any idea why SSL traffic isn't being passed correctly? Also, any other changes you would recommend? I still need to configure logging, so don't worry about that section. Thanks in advance your help.

    Read the article

  • Issues with creating a snapshot

    - by Andy Welcomer
    Hello everyone, We have a strange issue when attempting to create a snapshot in one of our regional environments. We have 4 VMs, 2 of them have mulitple VMDKs spread onto different datastores. When a snapshot is created, all the VMDKs (except for the first), seem to vanish. If you look at the properties of the VM, the path to the VMDKS points to the datastore where the primary VMDK is, and the file name is some random garbage. If the snapshot is deleted everything returns to normal. Has anyone ever seen this? I'm using ESX3.5 Thank you in advance. Andy ==============UPDATE============== Here is some more information. I just created a test machine with 7 VMDKs. 1 for the OS. and 6 others for data. All of the VMDKs are in seperate datastores. I take a snapshot of the machine, all of the 6 VMDKs loose their reference to the actual VMDK files. The all point to 64KB VMDK files in the datastore where the OS VMDK is located. These 64KB vmdks didn't exist until the snapshot was taken. When the snapshot is deleted, everything goes back to normal.

    Read the article

  • Creating a tar file with checksums included

    - by wazoox
    Here's my problem : I need to archive to tar files a lot ( up to 60 TB) of big files (usually 30 to 40 GB each). I would like to make checksums ( md5, sha1, whatever) of these files before archiving; however not reading every file twice (once for checksumming, twice for tar'ing) is more or less a necessity to achieve a very high archiving performance (LTO-4 wants 120 MB/s sustained, and the backup window is limited). So I'd need some way to read a file, feeding a checksumming tool on one side, and building a tar to tape on the other side, something along : tar cf - files | tee tarfile.tar | md5sum - Except that I don't want the checksum of the whole archive (this sample shell code does just this) but a checksum for each individual file in the archive. I've studied GNU tar, Pax, Star options. I've looked at the source from Archive::Tar. I see no obvious way to achieve this. It looks like I'll have to hand-build something in C or similar to achieve what I need. Perl/Python/etc simply won't cut it performance-wise, and the various tar programs miss the necessary "plugin architecture". Does anyone know of any existing solution to this before I start code-churning ?

    Read the article

  • Unix: Files starting with a dash, -

    - by Svish
    Ok, I have a bunch of files starting with a dash, -. Which is not so good... and I want to rename them. In my particular case I would just like to put a character in front of them. I found the following line that should work, but because of it dash it doesn't: for file in -N*.ext; do mv $file x$file; done If I put an echo in front of the mv I get a bunch of mv -N1.ext x-f1.ext mv -N2.ext x-f2.ext Which is correct, except of course it will think the first filename is options. So when I remove the echo and run it I just get a bunch of mv: illegal option -- N I have tried to change it to for file in -N*.ext; do mv "$file" "x$file"; done but the quotes are just ignored it seems. Tried to use single quotes, but then the variable wasn't expanded... What do I do here? Update: I have now also tried to quote the quotes. Like this: for file in -N*.ext; do mv '"'$file'"' '"'x$file'"'; done And when I echo that, it looks correct, but when I actually run it I just get mv: rename "-N1.ext" to "x-n1.ext":: No such file or directory I have just no clue how to do this now... sigh

    Read the article

  • Windows XP corrupts registry every several hours

    - by Ilya Kazakevich
    There is a Dell XPS 400 with Windows Media Center installer. It is installed on RAID (Intel Matrix Storage) which is built-in chipset south bridge. Raid has two 150 Gb WDC drivers connected as mirror. All drivers and updates are installed( sp3 and so on). A week ago PC changed its video mode to 256 colors (like VESA mode) and after several moments I got BSOD: c000021a: 0xc0000005 Doctor watson did not create dump although it is installed as default debugger. After reboot it said that config file is missing or corrupted. So, I boot to recovery console and found that registry file (config) is so small. I've replaced it with one from recovery point and windows booted sucessfully. But after about 3 hrs -- it has crashed again in the same wat! I look in event viewer: is said that Explorer.exe failed to open \global??\DLIAFS. I look in winobj, and found that it is a device. I made "deny from everyone" for this device ACL, and after several hours my windows crashed. I restored registry, boot again and there was no error about DLIAFS. I did full chkdsk and it did not found anything bad. But I found event about error paging to \Harddrive1\D. I do not have pagefile there, but I thought I should check my disk again. Unfortunatelly I cannt use smart tools for RAID, but I downloaded latest software from Intel (it can do the same things like RAID bios can but from windows). It verified my disks, found some errors, fix them, than I rebooted. And it crashed again. I am lost. What (except kernel debugging) could be done here? Thanks

    Read the article

  • Windows XP corrupts registry every several hours

    - by Ilya Kazakevich
    There is a Dell XPS 400 with Windows Media Center installer. It is installed on RAID (Intel Matrix Storage) which is built-in chipset south bridge. Raid has two 150 Gb WDC drivers connected as mirror. All drivers and updates are installed( sp3 and so on). A week ago PC changed its video mode to 256 colors (like VESA mode) and after several moments I got BSOD: c000021a: 0xc0000005 Doctor watson did not create dump although it is installed as default debugger. After reboot it said that config file is missing or corrupted. So, I boot to recovery console and found that registry file (config) is so small. I've replaced it with one from recovery point and windows booted sucessfully. But after about 3 hrs -- it has crashed again in the same wat! I look in event viewer: is said that Explorer.exe failed to open \global??\DLIAFS. I look in winobj, and found that it is a device. I made "deny from everyone" for this device ACL, and after several hours my windows crashed. I restored registry, boot again and there was no error about DLIAFS. I did full chkdsk and it did not found anything bad. But I found event about error paging to \Harddrive1\D. I do not have pagefile there, but I thought I should check my disk again. Unfortunatelly I cannt use smart tools for RAID, but I downloaded latest software from Intel (it can do the same things like RAID bios can but from windows). It verified my disks, found some errors, fix them, than I rebooted. And it crashed again. I am lost. What (except kernel debugging) could be done here? Thanks

    Read the article

< Previous Page | 196 197 198 199 200 201 202 203 204 205 206 207  | Next Page >