logical tree - Page 201

Windows Setup could not configure Windows to run on this computer's hardware

- by Hello71

The whole installation goes smoothly up to the point of "Completing installation ...". The monitor changes resolution, after which a standard dialog box pops up saying Windows Setup could not configure Windows to run on this computer's hardware Then, in a few seconds, the whole machine powers down. Trying to restart produces the message: STOP: c000021a {Fatal System Error} 0x00000000 (0xc0000001 0x00100448) OR it boots into Setup and comes up with the message: Windows Setup encountered an unexpected error... (This is not the actual error, just paraphrasing) I tried using the OEM restore instead of a regular install, but it fails with the same error. (Even though it worked before...) General specs: HP Pavilion Elite e9262f Intel Core i5-750 Processor ATI Radeon HD 4650 Hitachi HDT721010SLA360 ATA Device 6GB DDR3 RAM SuperMulti DVD Burner with LightScribe Some built-in Wi-Fi module http://h10025.www1.hp.com/ewfrf/wc/document?docname=c01916917 I've tried disconnecting the wireless card and disabling the built-in Ethernet and Firewire via the BIOS, and replacing the wireless keyboard and mouse with wired USB ones. Didn't work. I've also tried changing the SATA controller settings in the BIOS to RAID, AHCI, and IDE, reinstalling each time I changed. Still not working. I think the reason why it is showing the Fatal System Error is because it didn't finish installing before it errored out and shut down, so the system is left in an inconsistent state. I've tried 3 different copies (including the OEM restore) of Windows 7 now, and they're all failing at the same point, with the same error message. I've tried to install Windows 7 maybe 10 times already, with the exact same error message at the exact same location. Hm... Interestingly, the 32-bit version of Windows 7 works, but the 64-bit version doesn't. Perhaps it was a badly burned disk? Reburning the 64-bit version still comes up with the same error. Here's a picture of the side of the case that clearly says it came with Windows 7 64-bit, along with the model number and CPU. sudo fdisk -l: Disk /dev/sda: 1000.2 GB, 1000204886016 bytes 255 heads, 63 sectors/track, 121601 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x0009896f Device Boot Start End Blocks Id System /dev/sda1 * 1 13 104391 7 HPFS/NTFS /dev/sda2 14 94119 755906445 7 HPFS/NTFS /dev/sda3 119922 121602 13492224 7 HPFS/NTFS /dev/sda4 94120 119922 207257740+ 5 Extended /dev/sda5 119527 119922 3170769 82 Linux swap / Solaris /dev/sda6 107174 119526 99225441 83 Linux /dev/sda7 94120 107173 104856192 7 HPFS/NTFS Partition table entries are not in disk order

Read the article

lighttpd: weird behavior on multiple rewrite rule matches

- by netmikey

I have a 20-rewrite.conf for my php application looking like this: $HTTP["host"] =~ "www.mydomain.com" { url.rewrite-once += ( "^/(img|css)/.*" => "$0", ".*" => "/my_app.php" ) } I want to be able to put the webserver in kind of a "maintenance" mode while I update my application from scm. To do this, my idea was to enable an additional rewrite configuration file before this one. The 16-rewrite-maintenance.conf file looks like this: url.rewrite-once += ( "^/(img|css)/.*" => "$0", ".*" => "/maintenance_app.php" ) Now, on the maintenance page, I have a logo that doesn't get loaded. I get a 404 error. Lighttpd debug says the following: 2012-12-13 20:28:06: (response.c.300) -- splitting Request-URI 2012-12-13 20:28:06: (response.c.301) Request-URI : /img/content/logo.png 2012-12-13 20:28:06: (response.c.302) URI-scheme : http 2012-12-13 20:28:06: (response.c.303) URI-authority: localhost 2012-12-13 20:28:06: (response.c.304) URI-path : /img/content/logo.png 2012-12-13 20:28:06: (response.c.305) URI-query : 2012-12-13 20:28:06: (response.c.300) -- splitting Request-URI 2012-12-13 20:28:06: (response.c.301) Request-URI : /img/content/logo.png, /img/content/logo.png 2012-12-13 20:28:06: (response.c.302) URI-scheme : http 2012-12-13 20:28:06: (response.c.303) URI-authority: localhost 2012-12-13 20:28:06: (response.c.304) URI-path : /img/content/logo.png, /img/content/logo.png 2012-12-13 20:28:06: (response.c.305) URI-query : 2012-12-13 20:28:06: (response.c.349) -- sanatising URI 2012-12-13 20:28:06: (response.c.350) URI-path : /img/content/logo.png, /img/content/logo.png 2012-12-13 20:28:06: (mod_access.c.135) -- mod_access_uri_handler called 2012-12-13 20:28:06: (response.c.470) -- before doc_root 2012-12-13 20:28:06: (response.c.471) Doc-Root : /www 2012-12-13 20:28:06: (response.c.472) Rel-Path : /img/content/logo.png, /img/content/logo.png 2012-12-13 20:28:06: (response.c.473) Path : 2012-12-13 20:28:06: (response.c.521) -- after doc_root 2012-12-13 20:28:06: (response.c.522) Doc-Root : /www 2012-12-13 20:28:06: (response.c.523) Rel-Path : /img/content/logo.png, /img/content/logo.png 2012-12-13 20:28:06: (response.c.524) Path : /www/img/content/logo.png, /img/content/logo.png 2012-12-13 20:28:06: (response.c.541) -- logical -> physical 2012-12-13 20:28:06: (response.c.542) Doc-Root : /www 2012-12-13 20:28:06: (response.c.543) Rel-Path : /img/content/logo.png, /img/content/logo.png 2012-12-13 20:28:06: (response.c.544) Path : /www/img/content/logo.png, /img/content/logo.png 2012-12-13 20:28:06: (response.c.561) -- handling physical path 2012-12-13 20:28:06: (response.c.562) Path : /www/img/content/logo.png, /img/content/logo.png 2012-12-13 20:28:06: (response.c.618) -- file not found 2012-12-13 20:28:06: (response.c.619) Path : /www/img/content/logo.png, /img/content/logo.png Any clue on why lighttpd matches both rules (from my application rewrite config and from my maintenance rewrite config) and concatenates them with a comma - that doesn't seem to make any sense?! Shouldn't it stop after the first match with rewrite-once?

Read the article

Planning trunk capacity for multiple GbE switches

- by wuckachucka

Without measuring throughput (it's at the top of the list; this is just theoretical), I want to know the most standard method for trunking VLANs on multiple Gigabit (GbE) switches to a core Layer 3 GbE switch. Say you have three VLANs: VLAN10 (10.0.0.0/24) Servers: your typical Windows DC/file server, Exchange, and an Accounting/SQL server. VLAN20: (10.0.1.0/24) Sales: needs access to everything on VLAN10; doesn't need access to VLAN30 and vice-versa. VLAN20: (10.0.1.0/24) Support: needs access to everything on VLAN10; doesn't need access to VLAN20 and vice-versa. Here's how I think this should work in my head: Switch #1: Ports 2-20 are assigned to VLAN20; all the Sales workstations and printers are connected here. Optional 10GbE combo port #1 is trunked to L3 switch's 10 GbE combo port #1. Switch #2: Ports 2-20 are assigned to VLAN30; all the Support workstations and printers are connected here. Optional 10GbE combo port #1 is trunked to L3 switch's 10 GbE combo port #2. Core L3 switch: Ports 2-10 are assigned to VLAN10; all three servers are connected here. With a standard 10/100 x 24 switch, it'll usually come with one or two 1 GbE uplink ports; carrying over this logic to a 10/100/1000 x 24, the "optional" 10 GbE combo ports that most higher-end switches can get shouldn't really be an option. Keep in mind I haven't tested anything yet, I'm primarily moving in this direction for growth (don't want to buy 10/100 switches and have to replace those within a couple of years) and security (being able to control access between VLANs with L3 routing/packet filtering ACLs). Does this sound right? Do I really need the 10 GbE ports? It seems very non-standard and expensive, but it "feels" right when you think about 40 or 50 workstations trunking up to the L3 switch over 1 GbE standard ports. If say 20 workstations want to download a 10 GB image from the servers concurrently, wouldn't the trunk be the bottleneck? At least if the trunk was 10 GbE, you'd have 10x1GbE nodes being able to reach their theoretical max. What about switch stacking? Some of the D-Links I've been looking at have HDMI interfaces for stacking. As far as I know, stacking two switches creates one logical switch, but is this just for management I/O or does the switches use the (assuming it's HDMI 1.3) 10.2 Gbps for carrying data back and forth?

Read the article

DVD ROM is not working

- by Cyril N.

(note: I don't know in which StackExchange site to put this question, I'll thank the moderator that will move it to a more appropriate place, if there is a S.E. available for my question). I have a DVD RW drive that is well listed in the bios, and if no CD is in, it is also present in the "My Computer" of my Fedora 16. But when I put a disc on it, the icon disapear from "My Computer", and I can not do anything with this ! (Like erasing a RW disc). I'd like to boot a Fedora 17 Live CD image. I burned it on an other computer but when I try to run it in bios, nothing is done and I'm redirected to Grub of my HD. The command cdrecord -scanbus shows this : wodim: Warning: controller returns wrong size for CD capabilities page. wodim: Cannot get CD capabilities data. 6,1,0 601) 'HD-DT%ST' 'DVD%RAM G@22NP20' '1&04' Removable CD-ROM And when I try to mount manually the disc, I got this error : mount: block device /dev/sr0 is write-protected, mounting read-only mount: /dev/sr0: can't read superblock Here's a paste of dmesg | grep sr0 : [ 5.161265] sr0: scsi-1 drive [ 5.161621] sr 6:0:1:0: Attached scsi CD-ROM sr0 [ 834.545978] sr0: Hmm, seems the drive doesn't support multisession CD's [ 841.731194] sr0: CDROM (ioctl) error, command: Get configuration 46 00 00 00 00 00 00 00 20 00 [ 842.021640] sr 6:0:1:0: [sr0] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE [ 842.021652] sr 6:0:1:0: [sr0] Sense Key : Aborted Command [current] [ 842.021662] sr 6:0:1:0: [sr0] Add. Sense: No additional sense information [ 842.021672] sr 6:0:1:0: [sr0] CDB: Read(10): 28 00 00 00 00 00 00 00 02 00 [ 842.021688] end_request: I/O error, dev sr0, sector 0 [ 842.021697] Buffer I/O error on device sr0, logical block 0 [ 842.023715] sr 6:0:1:0: [sr0] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE [ 843.048203] sr 6:0:1:0: [sr0] Sense Key : Aborted Command [current] [ 843.048211] sr 6:0:1:0: [sr0] Add. Sense: No additional sense information [ 843.048219] sr 6:0:1:0: [sr0] CDB: Read(10): 28 00 00 00 00 00 00 00 01 00 [ 843.048234] end_request: I/O error, dev sr0, sector 0 [ 843.048274] EXT4-fs (sr0): unable to read superblock [ 843.063155] sr0: CDROM (ioctl) error, command: Get configuration 46 00 00 00 00 00 00 00 20 00 [ 843.075904] sr0: CDROM (ioctl) error, command: Get configuration 46 00 00 00 00 00 00 00 20 00 [ 843.220512] sr 6:0:1:0: [sr0] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE [ 843.220522] sr 6:0:1:0: [sr0] Sense Key : Aborted Command [current] [ 843.220530] sr 6:0:1:0: [sr0] Add. Sense: No additional sense information [ 843.220538] sr 6:0:1:0: [sr0] CDB: Read(10): 28 00 00 00 00 00 00 00 01 00 [ 843.220553] end_request: I/O error, dev sr0, sector 0 [ 843.220609] FAT-fs (sr0): unable to read boot sector The lines from Sense Key .. (line 6) to DRIVER_SENSE (line 11) are repeating a lot. I then changed my DVD player with an other spare one I had, and the disc didn't boot neither. I then changed the IDE cable, but still no success. What can I do to make it work? Thanks for your help.

Read the article

Do RAID controllers commonly have SATA drive brand compatibility issues?

- by Jeff Atwood

We've struggled with the RAID controller in our database server, a Lenovo ThinkServer RD120. It is a rebranded Adaptec that Lenovo / IBM dubs the ServeRAID 8k. We have patched this ServeRAID 8k up to the very latest and greatest: RAID bios version RAID backplane bios version Windows Server 2008 driver This RAID controller has had multiple critical BIOS updates even in the short 4 month time we've owned it, and the change history is just.. well, scary. We've tried both write-back and write-through strategies on the logical RAID drives. We still get intermittent I/O errors under heavy disk activity. They are not common, but serious when they happen, as they cause SQL Server 2008 I/O timeouts and sometimes failure of SQL connection pools. We were at the end of our rope troubleshooting this problem. Short of hardcore stuff like replacing the entire server, or replacing the RAID hardware, we were getting desperate. When I first got the server, I had a problem where drive bay #6 wasn't recognized. Switching out hard drives to a different brand, strangely, fixed this -- and updating the RAID BIOS (for the first of many times) fixed it permanently, so I was able to use the original "incompatible" drive in bay 6. On a hunch, I began to assume that the Western Digital SATA hard drives I chose were somehow incompatible with the ServeRAID 8k controller. Buying 6 new hard drives was one of the cheaper options on the table, so I went for 6 Hitachi (aka IBM, aka Lenovo) hard drives under the theory that an IBM/Lenovo RAID controller is more likely to work with the drives it's typically sold with. Looks like that hunch paid off -- we've been through three of our heaviest load days (mon,tue,wed) without a single I/O error of any kind. Prior to this we regularly had at least one I/O "event" in this time frame. It sure looks like switching brands of hard drive has fixed our intermittent RAID I/O problems! While I understand that IBM/Lenovo probably tests their RAID controller exclusively with their own brand of hard drives, I'm disturbed that a RAID controller would have such subtle I/O problems with particular brands of hard drives. So my question is, is this sort of SATA drive incompatibility common with RAID controllers? Are there some brands of drives that work better than others, or are "validated" against particular RAID controller? I had sort of assumed that all commodity SATA hard drives were alike and would work reasonably well in any given RAID controller (of sufficient quality).

Read the article

USB Flash not recognised by Windows and BIOS, but works fine in Linux

- by bbalegere

I have a Transcend JetFLash 2GB USB Drive.It was working fine and I had been using it occasionally. All of sudden it stopped working in all versions of Windows . The USB Drive is also not recognised by the BIOS.It does not show in the list of bootable devices.(It used show up in the list earlier) However the USB Drive works fine in my Linux Mint 11 OS. Running dmesg gives this [ 941.812192] usb 1-2: new high speed USB device using ehci_hcd and address 4 [ 941.936178] usb 1-2: device descriptor read/64, error -71 [ 942.164188] usb 1-2: device descriptor read/64, error -71 [ 942.380189] usb 1-2: new high speed USB device using ehci_hcd and address 5 [ 942.504138] usb 1-2: device descriptor read/64, error -71 [ 942.732179] usb 1-2: device descriptor read/64, error -71 [ 942.948154] usb 1-2: new high speed USB device using ehci_hcd and address 6 [ 943.364134] usb 1-2: device not accepting address 6, error -71 [ 943.476172] usb 1-2: new high speed USB device using ehci_hcd and address 7 [ 943.892140] usb 1-2: device not accepting address 7, error -71 [ 943.892191] hub 1-0:1.0: unable to enumerate USB device on port 2 [ 944.296190] usb 2-2: new full speed USB device using uhci_hcd and address 3 [ 944.438251] usb 2-2: not running at top speed; connect to a high speed hub [ 944.709928] usbcore: registered new interface driver uas [ 944.729999] Initializing USB Mass Storage driver... [ 944.730509] scsi6 : usb-storage 2-2:1.0 [ 944.730908] usbcore: registered new interface driver usb-storage [ 944.730917] USB Mass Storage support registered. [ 945.736320] scsi 6:0:0:0: Direct-Access JetFlash Transcend 2GB 8.07 PQ: 0 ANSI: 2 [ 945.744547] sd 6:0:0:0: Attached scsi generic sg1 type 0 [ 945.753316] sd 6:0:0:0: [sdb] 3944448 512-byte logical blocks: (2.01 GB/1.88 GiB) [ 945.758274] sd 6:0:0:0: [sdb] Write Protect is off [ 945.758288] sd 6:0:0:0: [sdb] Mode Sense: 03 00 00 00 [ 945.765167] sd 6:0:0:0: [sdb] No Caching mode page present [ 945.765181] sd 6:0:0:0: [sdb] Assuming drive cache: write through [ 945.784309] sd 6:0:0:0: [sdb] No Caching mode page present [ 945.784323] sd 6:0:0:0: [sdb] Assuming drive cache: write through [ 946.239512] sdb: sdb1 [ 946.257279] sd 6:0:0:0: [sdb] No Caching mode page present [ 946.257292] sd 6:0:0:0: [sdb] Assuming drive cache: write through [ 946.257302] sd 6:0:0:0: [sdb] Attached SCSI removable disk Looks like there is something wrong the USB Drive.It is not recognised in any computer running Windows. Is there any way to fix this? Any idea why this problem occurred ?

Read the article

Is my Cisco switch port bad?

- by ewwhite

I've been chasing a packet-loss and network stability issue for a handful of end-users on an internal network for the past few days... These issues surfaced last week, however the location was struck by lightning six weeks ago. I was seeing 5-10% packet loss between a stack of four Cisco 2960's and several PC's and phones on the other side of a 77-meter run. The PC's were run inline with the phones over a trunked link (switchport configuration pastebin). We were seeing dropped calls and interruptions in client-server applications and Microsoft Exchange connectivity. I tried the usual troubleshooting steps remotely, having a local technician do the following during breaks in user and production activity: change cables between the wall jack and device. change patch cables between the patch panel and switch port(s). try different switch ports within the 2960 stack. change end-user devices with known-good equipment (new phones, different PC's). clear switch port interface counters and monitor incrementing errors closely. (Pastebin output of sh int) Pored over the device logs and Observium RRD graphs. No link up/down issues from the switch side. change power strips on the end-user side. test cable runs from the Cisco 2960 using test cable-diagnostics tdr int Gi4/0/9 (clean)* test cable runs with a Tripp-Lite cable tester. (clean) run diagnostics on the switch stack members. (clean) In the end, it took three changes of switch ports to find a stable solution. The only logical conclusion is that a few Cisco 2960 switch ports are bad or flaky... Not dead, but not consistent in behavior either. I'm not used to seeing individual ports die in this manner. What else can I test or check to determine if these devices are bad? Is it common for single ports to have problems, rather than a contiguous bank of ports? BTW - show cable-diagnostics tdr int Gi4/0/14 is very cool... Interface Speed Local pair Pair length Remote pair Pair status --------- ----- ---------- ------------------ ----------- -------------------- Gi4/0/14 1000M Pair A 79 +/- 0 meters Pair B Normal Pair B 75 +/- 0 meters Pair A Normal Pair C 77 +/- 0 meters Pair D Normal Pair D 79 +/- 0 meters Pair C Normal

Read the article

flashcache with mdadm and LVM

- by Backtogeek

I am having trouble setting up flashcache on a system with LVM and mdadm, I suspect I am either just missing an obvious step or getting some mapping wrong and hoped someone could point me in the right direction? system info: CentOS 6.4 64 bit mdadm config md0 : active raid1 sdd3[2] sde3[3] sdf3[4] sdg3[5] sdh3[1] sda3[0] 204736 blocks super 1.0 [6/6] [UUUUUU] md2 : active raid6 sdd5[2] sde5[3] sdf5[4] sdg5[5] sdh5[1] sda5[0] 3794905088 blocks super 1.1 level 6, 512k chunk, algorithm 2 [6/6] [UUUUUU] md3 : active raid0 sdc1[1] sdb1[0] 250065920 blocks super 1.1 512k chunks md1 : active raid10 sdh1[1] sda1[0] sdd1[2] sdf1[4] sdg1[5] sde1[3] 76749312 blocks super 1.1 512K chunks 2 near-copies [6/6] [UUUUUU] pcsvan PV /dev/mapper/ssdcache VG Xenvol lvm2 [3.53 TiB / 3.53 TiB free] Total: 1 [3.53 TiB] / in use: 1 [3.53 TiB] / in no VG: 0 [0 ] flashcache create command used: flashcache_create -p back ssdcache /dev/md3 /dev/md2 pvdisplay --- Physical volume --- PV Name /dev/mapper/ssdcache VG Name Xenvol PV Size 3.53 TiB / not usable 106.00 MiB Allocatable yes PE Size 128.00 MiB Total PE 28952 Free PE 28912 Allocated PE 40 PV UUID w0ENVR-EjvO-gAZ8-TQA1-5wYu-ISOk-pJv7LV vgdisplay --- Volume group --- VG Name Xenvol System ID Format lvm2 Metadata Areas 1 Metadata Sequence No 2 VG Access read/write VG Status resizable MAX LV 0 Cur LV 1 Open LV 1 Max PV 0 Cur PV 1 Act PV 1 VG Size 3.53 TiB PE Size 128.00 MiB Total PE 28952 Alloc PE / Size 40 / 5.00 GiB Free PE / Size 28912 / 3.53 TiB VG UUID 7vfKWh-ENPb-P8dV-jVlb-kP0o-1dDd-N8zzYj So that is where I am at, I thought that was the job done however when creating a logical volume called test and mounting it is /mnt/test the sequential write is pathetic, 60 ish MB/s /dev/md3 has 2 x SSD's in Raid0 which alone is performing at around 800 MB/s sequential write and I am trying to cache /dev/md2 which is 6 x 1TB drives in raid6 I have read a number of pages through the day and some of them here, it is obvious from the results that the cache is not functioning but I am unsure why. I have added the filter line in the lvm.conf filter = [ "r|/dev/sdb|", "r|/dev/sdc|", "r|/dev/md3|" ] It is probably something silly but the cache is clearly performing no writes so I suspect I am not mapping it or have not mounted the cache correctly. dmsetup status ssdcache: 0 7589810176 flashcache stats: reads(142), writes(0) read hits(133), read hit percent(93) write hits(0) write hit percent(0) dirty write hits(0) dirty write hit percent(0) replacement(0), write replacement(0) write invalidates(0), read invalidates(0) pending enqueues(0), pending inval(0) metadata dirties(0), metadata cleans(0) metadata batch(0) metadata ssd writes(0) cleanings(0) fallow cleanings(0) no room(0) front merge(0) back merge(0) force_clean_block(0) disk reads(9), disk writes(0) ssd reads(133) ssd writes(9) uncached reads(0), uncached writes(0), uncached IO requeue(0) disk read errors(0), disk write errors(0) ssd read errors(0) ssd write errors(0) uncached sequential reads(0), uncached sequential writes(0) pid_adds(0), pid_dels(0), pid_drops(0) pid_expiry(0) lru hot blocks(31136000), lru warm blocks(31136000) lru promotions(0), lru demotions(0) Xenvol-test: 0 10485760 linear I have included as much info as I can think of, look forward to any replies.

Read the article

Operative systems on SD cards

- by HisDudeness

I was getting some wild ideas the last days, like putting some operative systems into SD cards rather than on my hard drive. I'll go further into details now and explain what lead me to consider this probably abominable decision. I am on a laptop (that means I have a native SD-card reader) which is currently running a cross-distro setup, with a bunch of Linux systems (placed in dedicated ext4 logical partitions into a huge extended one) regulated by an unique GRUB. Since today, my laptop haven't even seen any Windows system with binoculars. I was thinking about placing all the os part of my setup into a Secure Digital to save all my 500 Gb Hard Drive for documents, music, videos and so on, and being able to just remove the SD and boot my system into another computer too, as well as having the possibility of booting other systems into mine by just plugging in another SD, without having to keep it constantly placed in my PC. Also, in the remote case in the near future I just wanted to boot Windows 8 in it, I read it causes major boot incompatibility issues with other systems by needing a digital signature in order for them to start. By having it in a removable drive, I could just get rid of it when I'm needing him and switch its card with Linux one, and so not having any obstacles to their boot. Now, my questions are: I know unlikely traditional rotating disk drives, integrated circuits ones have a limited lifespan in terms of cluster rewriting. Is it an obstacle to that kind of usage? I mean, some Ultrabooks are using SSD now, is it the same issue, or there are some differences between Solid State Drives and Secure Digitals in that sense? Maybe having them to store system files which are in fixed positions (making the even-usage of cluster technology useless) constantly being re-read and updated and similar things just gets them soon unserviceable, do it? Second question: are all motherboards and BIOSes able to boot from SDs just like they are from USB pen drives (I mean, provided card reader is USB-connected, isn't it)? Or can't bootloaders like GRUB be installed on SDs working? If they can't, is it a solution installing GRUB to MBR and making boot option pointing to SD? Will it work? Are there any other problems to installing OSs on a Secure Digital?

Read the article

Can't Move Windows to 2nd Monitor without Left Mouse and Cntl Key

- by John C

I have 2 very frustrating problems that maybe someone can help me with: I have 2 monitors (different sizes and resolutions) setup with the "Extended" monitor Win7 setup. My problem is this = I can not "move" a window from my Primary Monitor (larger and higher resolution on right side in front of me) to my Secondary 2nd monitor (smaller and lower resolution) with just selecting the title bar with the left mouse button and dragging it to the left. Windows 7 "snaps" it back to the left Primary Monitor when the window is physically in the 2nd window area as I'm holding the left mouse button. I can prevent this problem - by holding down the Cntl Key with the Left Mouse button, but this is extremely annoying to me. Also I typically "lose" focus if I try typing input on the 2nd monitor. Typing is erratic with regard to keystroke accuracy from my keyboard translated into input on the 2nd screen. No problem with typing input on the primary left monitor. I find this extremely annoying in Windows 7 and turning off the "snap" feature via the Control panel does NOT work for me. Win7 stubbornly refuses to move my selected window to my 2nd monitor without me "forcing" Win7 to do this with the Cntrl Key. Please tell me this is not a Win7 feature. Also on my system - Windows Key + Shift, Left arrow Key (pressed together) or the same combo with The Right arrow Key - don't do anything whatsoever. Widows Key with "+" however does maximize current window across both monitors, and I can "restore" it with Windows Key and "-" back to original monitor and size. I have tried various solutions including changing the resolutions of one or both of my monitors and sometimes "temporarily helps" but reverts back to the problem. Also if I swap the logical (not physical) layout so that I tell Win7 the monitors are setup in a reserved situation (Large monitor on the left, and small on the right) - this also sometimes helps for awhile - and is very strange and awkward to work with "backwards". But all of these solutions stop working. The only solution that consistently works for "moving" the screens is to hold the Cntrl Key down as I'm moving window with the left mouse selected on the title bar. Even that however, doesn't prevent the loss of typing focus for me on the 2nd monitor - while at the same time the typing on the 1st monitor is fine. Any help on moving my window screens from one monitor on my 2nd monitor without having to press the Cntrl key while holding down my left mouse button with be appreciated. Also any help on gaining typing "focus" into my 2nd screen with be helpful too. Thanks - John

Read the article

Can't validate mine, sudo nor root in Debian "Jessie" Gnome anymore?

- by Janar

I'm Debian beginner & GUI guy in a bit of trouble? Can't login as sudo/gksu/root/su nor as (main/super)user after removed user password via Gnome-user-settings. History of actions (Probably irrelevant though) Installed Debian "Jessie" GNU/Linux with xFce GUI (en-US) as only OS. HardWare is ThinkPad w510. Skipped root user password in setup, to get sudo for superuser easily. Logged in (as always had) with Gnome (3.4.x), not once with xFCE. (installed Xfce. Installed xFce only to achieve more control (easier management) over packages this way, to set-up gnome much more by mine likes. Added more jessie repros (same ones as in Wheesy stable by default but for Jessie as, Jessie only had repros for security updates by default). Installed lots of gtk(3) & gnome(3) based soft; (- restarted again after this) Installed propietary graphics card driver for mine nvidia quadro. (- restarted once again after that one) Installed more stuff related to mine work/school/devel. The actual problem Had a plan to restart again, but wanted to set up auto-login first, instead set user password to none (don't ask why / perhaps caused by being awake for a looooong time), noticed it, and set also to auto-login, but couldn't undo mine previous mistake to create new password for me. As mine password is set to none I would have expected that simply return in pass prompt for emty password field would do, but it won't authenticate. I tried Alt+F2 "gksu gedit" as well as: sudo wget "https://www.some-page.eu/file.ext" and "su" in terminals, none has applied (quite logical actually - as I'm sudoer and highest ranked super user, besides only user in computer). Current stand Everything worked & still works nice after this accident, besides this password prompts part. To spoked to log-out nor restart. Synaptic package-manager is still open with root rights (only one, that has left open prior to the issue and not closed since, just in case). Goggled for help and read some manuals/faqs/how-tos - mostly lead to sudoers file management, but not found one specifically for mine issue - so still not any smarter. Really hope, that I don't have to redo OS inst all over again, by just one stupid mistake. Thanks for your reply :-)

Read the article

Second HDD not seen by Windows 7 on Dell Xps l501x

- by George

I have a Dell XPS Laptop (l501x). I have replaced the original Seagate 500GB hard drive with an SSD Intel 320 120GB when I first purchased it a year ago. It's been working great. The laptop is booting in about 23 seconds, so the SSD is great. I have an Acronis image created that I came back to every three months just to keep everything clean. The SSD is partitioned with one logical drive for my data. So, recently I thought since I am not using my optical drive often enough to swap it out with a HDD caddy and add my seagate 500gb hard drive. I ordered the caddy placed the HDD in it and now load Windows. It just hangs on the screen that should show the Windows logo. I have tried everything that I know and searched it online. I have uninstalled the SATA controller AHCI and let Windows install it. Still will not boot into windows. I wanted to mention that the Seagate 500GB drive was the one that came with my laptop before I switched to the Intel SSD. As you know Intel has this application called Intel Rapid Technology which loads once in a while and shows the second hard drive, but then, when I restart it hangs again and Windows will not load. As soon as I remove the HDD Caddy and restart it loads Windows fine. I also formated the Seagate 500GB HDD in NTFS and still Windows will not load. When I go into the BIOS it shows the Fixed SSD and also "Sata ODD 500GB" instead of the optical drive but it will not boot into Windows when the HDD caddy is present. There is nothing wrong with the caddy. I have another laptop (Asus) and I installed the HDD caddy and Windows 7 loads without any glitch. I don't get it. I have also flashed the BIOS because Dell had a new version (A08). I also wanted to add that I refreshed Disk Management and the Device Manager and the second drive does not display. At this point I think it's a Windows issue so before I reinstall Windows 7 Home Premium from scratch I wanted to see if there was anything I was missing. Any advice would be greatly appreciated.

Read the article

Linux software Raid 10 no superblock

- by Shoshomiga

I have a software raid 10 with 6 x 2tb hard drives (raid 1 for /boot), ubuntu 10.04 is the os. I had a raid controller failure that put 2 drives out of sync, crashed the system and initially the os didnt boot up and went into initramfs instead, saying that drives were busy but I eventually managed to bring the raid up by stopping and assembling the drives. The os booted up and said that there were filesystem errors, I chose to ignore because it would remount the fs in read-only mode if there was a problem. Everything seemed to be working fine and the 2 drives started to rebuild, I was sure that it was a sata controller failure because I had dma errors in my log files. The os crashed soon after that with ext errors. Now its not bringing up the raid, it says that there is no superblock on /dev/sda2. I tried to reassemble manually with all the device names but it still would not bring up the raid 10 complaining about the missing superblock on sda2, and sda1 was also dropped from the raid 1. When I did examine on the raid10 it says that 1 of the initially failed drives is a spare, the other is spare rebuilding and sda2 is removed. It seems that sda decided to fail right when the system was vulnerable to it because when I boot up a live cd it spews out sda unrecoverable read failures. I have been trying to fix this all week but I'm not sure where to go with this now, I ordered more hard drives because I didn't have a complete backup, but its too late for that now and the only thing I could do is mirror all the hard drives onto the new ones (I'm not sure whether sda was mirrored without errors). On the internet I read that you can recover from this by recreating the array with the same options as when it was made, however because sda is failing I cant use it and I don't want to risk using its mirror instead, so I'm waiting to get another hard drive. I'm also not sure whether to include the out of sync drives or if I can actually use those instead to recover the array. Sorry if this is a mess to read but I've been trying to fix this all day and its late at night now, any thoughts on this would be greatly appreciated. I also did a memtest and changed the motherboard in addition to everything else. EDIT: This is my partition layout Disk /dev/sdb: 2000.4 GB, 2000398934016 bytes 255 heads, 63 sectors/track, 243201 cylinders, total 3907029168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 4096 bytes I/O size (minimum/optimal): 4096 bytes / 4096 bytes Disk identifier: 0x0009c34a Device Boot Start End Blocks Id System /dev/sdb1 * 2048 511999 254976 83 Linux /dev/sdb2 512000 3904980991 1952234496 83 Linux /dev/sdb3 3904980992 3907028991 1024000 82 Linux swap / Solaris

Read the article

Triple (3) Monitors under Linux

- by widgisoft

I have a 3 monitor setup (each 1680x1050) via an Nvidia NVS440 (2 GPUs, 2 outputs per GPU totalling 4 outputs); this works fine under Windows XP,7 but caused considerable headaches under Linux (Ubuntu 9.04). I had previously used an XFX 9600GT and the onboard XFX 9300GS to produce the same result but the card was noisy and power hungry and I was hoping that there was some magical switch in the NVS4400 that got rid of this annoying problem - turns out the NVS440 is just 2 cards on one physical PCB :-p (I searched the net high and low for people using this card under Linux but found nothing, if anything the card uses less power and is fan less so I was to benefit from it either way) Anyway, using either set up there were 5 solutions available: Have 3 separate X instances, all un joined Have 3 separate X instances, adjoined by Xinerama Have 2 separate X instances - One using twin-view, both adjoined by Xinerama Have 2 separate X instances - One using twin-view but no Xinerama Have a single Twin-view setup and leave the 3rd screen unplugged :-p The 4rd option, using 2 separate X instances and twinview (but no xinerama) was the best balance in terms of performance and usability but caused 2 really annoying issues You couldn't control (without altering the shortcuts) which screen an application opened onto - and once it was opened you couldn't move it to another screen without opening up terminal and forcing it to move Nvidia's overriding or falsifying of Xinerama breaks and the 2 screens joined by Twin view behave like a single huge screen causing popups to open in the middle of both screens and maximising of windows stretches to the width of the first 2 screens Firefox can only run one instance as the same user so having multiple firefox windows requires at least 2 users The second option "feels" like the right option, but OpenGL is basically disabled and playing any sort of game or even running anything graphical causes a huge performance drop and instability - even trying to run a basic emulator for gba or gens just causes the system to fall over. It works just enough to stare at your desktop and do nothing but as soon as you start doing some work - opening windows, dragging things around - running multiple copies of firefox it just really feels slow. The last open, only going dual screen works perfectly and everything performs as required, full GPU acceleration - two logical screen spaces - perfect, just make it work across GPUs like windows! :-p Anyway, I know RandR was supposed to pick up the slack when it would introduced GPU objects of sorts to allow multiple GPUs to be stitched together to create one huge desktop at a much deeper layer than Xinerama. I was wondering if this has now been fixed (I noticed X server 1.7 is out) and whether anyone has got it running successfully? Again, my requirements are: One huge desktop to drag any window across Maximising of windows to each screen (as XP does) Running fullscreen apps on the primary screen and disabling the mouse from moving onto the others or on all 3 stretched Finally as a side note; I am aware of the Matrox triple (and dual) head splitter but even the price they go for on eBay is more than I can afford atm, my argument: I shouldn't have to buy extra hardware to get something to work on Linux when it's something that's existed in the windows world for a long time (can you tell I don't get on with X :-p); If I had the cash I'd have bought the latest version of this box already (the new version finally supports large resolutions as the displays I have 1680x1050 each).

Read the article

Software Raid 10 corrupted superblock after dual disk failure, how do I recover it?

- by Shoshomiga

I have a software raid 10 with 6 x 2tb hard drives (raid 1 for /boot), ubuntu 10.04 is the os. I had a raid controller failure that put 2 drives out of sync, crashed the system and initially the os didnt boot up and went into initramfs instead, saying that drives were busy but I eventually managed to bring the raid up by stopping and assembling the drives. The os booted up and said that there were filesystem errors, I chose to ignore because it would remount the fs in read-only mode if there was a problem. Everything seemed to be working fine and the 2 drives started to rebuild, I was sure that it was a sata controller failure because I had dma errors in my log files. The os crashed soon after that with ext errors. Now its not bringing up the raid, it says that there is no superblock on /dev/sda2, even if I assemble manually with all the device names. I also did a memtest and changed the motherboard in addition to everything else. EDIT: This is my partition layout Disk /dev/sdb: 2000.4 GB, 2000398934016 bytes 255 heads, 63 sectors/track, 243201 cylinders, total 3907029168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 4096 bytes I/O size (minimum/optimal): 4096 bytes / 4096 bytes Disk identifier: 0x0009c34a Device Boot Start End Blocks Id System /dev/sdb1 * 2048 511999 254976 83 Linux /dev/sdb2 512000 3904980991 1952234496 83 Linux /dev/sdb3 3904980992 3907028991 1024000 82 Linux swap / Solaris All 6 disks have the same layout, partition #1 is for raid 1 /boot, partition #2 is for raid 10 far plan, partition #3 is swap, but sda did not have swap enabled EDIT2: This is the output of mdadm --detail /dev/md1 Layout : near=1, far=2 Chunk Size : 64k UUID : a0feff55:2018f8ff:e368bf24:bd0fce41 Events : 0.3112126 Number Major Minor RaidDevice State 0 8 34 0 spare rebuilding /dev/sdc2 1 0 0 1 removed 2 8 18 2 active sync /dev/sdb2 3 8 50 3 active sync /dev/sdd2 4 0 0 4 removed 5 8 82 5 active sync /dev/sdf2 6 8 66 - spare /dev/sde2 EDIT3: I ran ddrescue and it has copied everything from sda except a single 4096 byte sector that I suspect is the raid superblock EDIT4: Here is some more info too long to fit here lshw: http://pastebin.com/2eKrh7nF mdadm --detail /dev/sd[abcdef]1 (raid1): http://pastebin.com/cgMQWerS mdadm --detail /dev/sd[abcdef]2 (raid10): http://pastebin.com/V5dtcGPF dumpe2fs of /dev/sda2 (from the ddrescue cloned drive): http://pastebin.com/sp0GYcJG I tried to recreate md1 based on this info with the command mdadm --create /dev/md1 -v --assume-clean --level=10 --raid-devices=6 --chunk=64K --layout=f2 /dev/sda2 missing /dev/sdc2 /dev/sdd2 missing /dev/sdf2 But I can't mount it, I also tried to recreate it based on my initial mdadm --detail /dev/md1 but it still doesn't mount It also warns me that /dev/sda2 is an ext2fs file system but I guess its because of ddrescue

Read the article

PC will POST whenever feels likes it

- by kyrpas

I'm really sick of my PC and I'd love to throw it off the 5th floor but unfortunately I don't have this luxury right now. The issues started when I moved to a new house about 2 months ago. I didn't have this problem before. Case: Arctic Cooling Silentium T1 with embedded Fusion 550 Eco 80 PSU. M/B: ASRock A790GMH/128M Gfx: ATI Radeon HD 5770 Here's what's happening almost on a daily basis: I wake up in the morning, switch on the PC and all the fans start spinning. 9/10 the graphics fan stays on 100% and I know it won't post. If I'm lucky, ATI's fan stays on full power for a second, then goes back to normal and I get a normal post but that doesn't happen often. No, instead it's just drives me crazy. When I get no POST I'm trying a lot of different things and what bothers me the most is that they all work. But not always. No... That way I could find out what the hell is going on and we don't want that.. right? So, sometimes it manages to POST if I: remove the keyboard remove the power cable for a few minutes remove the graphics card remove the HDD cables do nothing, just turn it on and off a few times Sometimes it doesn't POST even if I do all of the above. And I end up removing all power cables from the M/B, and connecting all the stuff one by one. Sometimes it works, sometimes it doesn't and I just have to pray and wait. What the hell is that? I'm getting pissed of again just thinking about it. The only solution is to leave it on 24/7 but I don't want to do that. It should be able to turn on and off when I press the power button. I'm not asking much. I'm starting to think there's some weird electricity/power issue but I really don't understand what it is. There's no logical explanation about it. At least I can't find one. Any ideas?

Read the article

If Nvidia Shield can stream a game via wifi, why can I not do the same via ethernet to any other PC?

- by Enigma

I think it absurd that a wireless game streaming solution is the *first to hit the market when a 1000mbps+ Ethernet connection would accomplish the same feat with roughly 6x the available bandwidth. I can only assume that there must be some reason behind this or a limitation preventing this, but what? 150mbps wifi is in no way superior to a 1000mbps LAN connection aside from well wireless mobility. Not only that but I have a secondary laptop and desktop which should by hardware comparison completely outperform anything the Tegra in the Nvidia Shield can do. Is this all just a marketing scheme to force people to buy the shield for the streaming benefit? Chief among these is that NVIDIA’s Shield handheld game console will be getting a microconsole-like mode, dubbed “Shield Console Mode”, that will allow the handheld to be converted into a more traditional TV-connected console. In console mode Shield can be controlled with a Bluetooth controller, and in accordance with the higher resolution of TVs will accept 1080p game streaming from a suitably equipped PC, versus 720p in handheld mode. With that said 1080p streaming will require additional bandwidth, and while 720p can be done over WiFi NVIDIA will be requiring a hardline GigE connection for 1080p streaming (note that Shield doesn’t have Ethernet, so this is presumably being done over USB). Streaming aside, in console mode Shield will also support its traditional local gaming/application functionality. - http://www.anandtech.com/show/7435/nvidia-consolidates-game-streaming-tech-under-gamestream-brand-announces-shield-console-mode ^ This is not acceptable for me for a number of reasons not to mention the ridiculousness of having a little screen+controller unit sitting there while using a secondary controller and screen instead. That kind of redundant absurdity exemplifies how wrong of a solution that is. They need a second product for this solution without the screen or controller for it to make sense... at which point your just buying a little computer that does what most other larger computers do better. All that is required, by my understanding, is the ability to decode H.264 video compression and transmit control/feedback so by any logical comparison, one (Nvidia especially) should have no difficulty in creating an application for PC's (win32/64 environment) that does the exact same thing their android app does. I have 2 video cards capable of streaming (encoding) H.264 so by right they must be capable of decoding it I would think. I haven't found anything stating plans to allow non-shield owners to do this. Can a third party create this software or does it hinge on some limitation that only Nvidia can overcome? (*) - perhaps this isn't the first but afaik it is the first complete package.

Read the article

HP Proliant G7 hardware RAID configuration automation with ribcl

- by karthik

I have been trying to automate hardware RAID configuration of HP proliant machines before OS installation (So I can not use hpacucli) ssh into iLO3 doesn't have option for RAID configuration I use ribcl but there is no command for RAID config, however I see this under the command GET_EMBEDDED_HEALTH. <STORAGE> <CONTROLLER> <LABEL VALUE="Controller on System Board"/> <STATUS VALUE="OK"/> <CONTROLLER_STATUS VALUE="OK"/> <SERIAL_NUMBER VALUE="50014380215F0070"/> <MODEL VALUE="HP Smart Array P420i Controller"/> <FW_VERSION VALUE="3.41"/> <DRIVE_ENCLOSURE> <LABEL VALUE="Port 1I Box 1"/> <STATUS VALUE="OK"/> <DRIVE_BAY VALUE="04"/> </DRIVE_ENCLOSURE> <DRIVE_ENCLOSURE> <LABEL VALUE="Port 2I Box 0"/> <STATUS VALUE="OK"/> <DRIVE_BAY VALUE="01"/> </DRIVE_ENCLOSURE> <LOGICAL_DRIVE> <LABEL VALUE="01"/> <STATUS VALUE="OK"/> <CAPACITY VALUE="68 GB"/> <FAULT_TOLERANCE VALUE="RAID 0"/> <PHYSICAL_DRIVE> <LABEL VALUE="Port 1I Box 1 Bay 3"/> <STATUS VALUE="OK"/> <SERIAL_NUMBER VALUE="6TA0N3SZ0000B231CYDT"/> <MODEL VALUE="EH0072FAWJA"/> <CAPACITY VALUE="68 GB"/> <LOCATION VALUE="Port 1I Box 1 Bay 3"/> <FW_VERSION VALUE="HPDH"/> <DRIVE_CONFIGURATION VALUE="Configured"/> </PHYSICAL_DRIVE> </LOGICAL_DRIVE> </CONTROLLER> </STORAGE> My question is, is there a way I modify/create this xml piece (say I have 2 Logical drive with one spare) and reboot the server it takes effect ? If this approach is not correct are there any other ways to automate hardware raid config ?

Read the article

USB hard drive not recognized

- by user318772

Until recently I was using the portable USB hard drive in my win 7 laptop and ubuntu laptop. Suddenly now none of the laptops recognize it. This is the message i get by doing lsusb... Bus 001 Device 004: ID 1058:1010 Western Digital Technologies, Inc. Elements External HDD Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 003 Device 003: ID 0b97:7762 O2 Micro, Inc. Oz776 SmartCard Reader Bus 003 Device 002: ID 0b97:7761 O2 Micro, Inc. Oz776 1.1 Hub Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 002 Device 002: ID 413c:a005 Dell Computer Corp. Internal 2.0 Hub Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub fdisk doesn't show the external hard drive Disk /dev/sda: 80.0 GB, 80026361856 bytes 255 heads, 63 sectors/track, 9729 cylinders, total 156301488 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x0004a743 Device Boot Start End Blocks Id System /dev/sda1 * 2048 152111103 76054528 83 Linux /dev/sda2 152113150 156301311 2094081 5 Extended /dev/sda5 152113152 156301311 2094080 82 Linux swap / Solaris when i do testdisk TestDisk 6.14, Data Recovery Utility, July 2013 Christophe GRENIER <[email protected]> http://www.cgsecurity.org TestDisk is free software, and comes with ABSOLUTELY NO WARRANTY. Select a media (use Arrow keys, then press Enter): >Disk /dev/sda - 80 GB / 74 GiB - ST980825AS Disk /dev/sdb - 2199 GB / 2048 GiB testdisk-> Intel->analyse I get partition error Disk /dev/sdb - 2199 GB / 2048 GiB - CHS 2097152 64 32 Current partition structure: Partition Start End Size in sectors Partition: Read error Here is the output of dmesg [11948.549171] Add. Sense: Invalid command operation code [11948.549177] sd 2:0:0:0: [sdb] CDB: [11948.549181] Read(16): 88 00 00 00 00 00 00 00 00 00 00 00 00 08 00 00 [11948.550489] sd 2:0:0:0: [sdb] Invalid command failure [11948.550495] sd 2:0:0:0: [sdb] [11948.550499] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE [11948.550505] sd 2:0:0:0: [sdb] [11948.550508] Sense Key : Illegal Request [current] [11948.550514] Info fld=0x0 [11948.550519] sd 2:0:0:0: [sdb] [11948.550525] Add. Sense: Invalid command operation code [11948.550531] sd 2:0:0:0: [sdb] CDB: [11948.550534] Read(16): 88 00 00 00 00 00 00 00 00 00 00 00 00 08 00 00 [11948.551870] sd 2:0:0:0: [sdb] Invalid command failure [11948.551876] sd 2:0:0:0: [sdb] [11948.551880] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE [11948.551885] sd 2:0:0:0: [sdb] [11948.551888] Sense Key : Illegal Request [current] [11948.551895] Info fld=0x0 [11948.551900] sd 2:0:0:0: [sdb] [11948.551905] Add. Sense: Invalid command operation code [11948.551911] sd 2:0:0:0: [sdb] CDB: [11948.551914] Read(16): 88 00 00 00 00 00 00 00 00 00 00 00 00 08 00 00 If possible i want to retrive at least some data from this hard drive. If thats not possible I would like to format it and use it. Any help will be greatly appreciated Thanks

Read the article

Network unreachable on Ubuntu guest after trying to set up a host only network on Virtualbox

- by gkb0986

I have a Mac OS X host and a bunch of guests including Ubuntu and Arch Linux. I was trying to set up a host-only network at eth1 to let me ssh into the system. But now eth0 isn't working properly either. Ubuntu can no longer connect to remote hosts or browse the internet. It tells me that the network is unreachable. What's gone wrong here? I've included some diagnostics below. $ifconfig lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:10968 errors:0 dropped:0 overruns:0 frame:0 TX packets:10968 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:897264 (897.2 KB) TX bytes:897264 (897.2 KB) Other diagnostic commands and the output: $sudo lspci -n 00:00.0 0600: 8086:1237 (rev 02) 00:01.0 0601: 8086:7000 00:01.1 0101: 8086:7111 (rev 01) 00:02.0 0300: 80ee:beef 00:03.0 0200: 8086:100e (rev 02) 00:04.0 0880: 80ee:cafe 00:05.0 0401: 8086:2415 (rev 01) 00:06.0 0C03: 106B:003F 00:07.0 0680: 8086:7113 (REV 08) 00:0D.0 0106: 8086:2829 (REV 02) $sudo lshw -c network *-network DISABLED description: Ethernet interface product: 82540EM Gigabit Ethernet Controller vendor: Intel Corporation physical id: 3 bus info: pci@0000:00:03.0 logical name: eth0 version: 02 serial: 08:00:27:7d:22:df size: 1Gbit/s capacity: 1Gbit/s width: 32 bits clock: 66MHz capabilities: pm pcix bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=e1000 driverversion=7.3.21-k8-NAPI duplex=full firmware=N/A latency=64 link=no mingnt=255 multicast=yes port=twisted pair speed=1Gbit/s resources: irq:19 memory:f0000000-f001ffff ioport:d010(size=8) $lsmod Module Size Used by nls_utf8 12557 1 isofs 40257 1 vboxsf 43743 2 vesafb 13844 1 snd_intel8x0 38570 2 snd_ac97_codec 134869 1 snd_intel8x0 ac97_bus 12730 1 snd_ac97_codec snd_pcm 97275 2 snd_intel8x0,snd_ac97_codec snd_seq_midi 13324 0 snd_rawmidi 30748 1 snd_seq_midi snd_seq_midi_event 14899 1 snd_seq_midi rfcomm 47604 0 snd_seq 61929 2 snd_seq_midi,snd_seq_midi_event bnep 18281 2 bluetooth 180113 10 rfcomm,bnep ppdev 17113 0 psmouse 97519 0 snd_timer 29990 2 snd_pcm,snd_seq joydev 17693 0 snd_seq_device 14540 3 snd_seq_midi,snd_rawmidi,snd_seq vboxvideo 12622 1 serio_raw 13211 0 snd 79041 11 snd_intel8x0,snd_ac97_codec,snd_pcm,snd_rawmidi,snd_seq,snd_timer,snd_seq_device soundcore 15091 1 snd vboxguest 235498 7 vboxsf parport_pc 32866 0 drm 241971 2 vboxvideo i2c_piix4 13301 0 snd_page_alloc 18529 2 snd_intel8x0,snd_pcm mac_hid 13253 0 lp 17799 0 parport 46562 3 ppdev,parport_pc,lp usbhid 47238 0 hid 99636 1 usbhid e1000 108589 0

Read the article

Can't recover hard drive

- by BreezyChick89

My drive got corrupt after a thunderstorm. It used to be 1 partition of 2.5tb but now it shows 2 partitions. It's weird because 300gig free space is about how much it had before corrupting, but it was part of the first partition. I tried $ sudo resize2fs -f /dev/sdb1 Resizing the filesystem on /dev/sdb1 to 536870911 (4k) blocks. resize2fs: Can't read an block bitmap while trying to resize /dev/sdb1 Please run 'e2fsck -fy /dev/sdb1' to fix the filesystem after the aborted resize operation. sudo e2fsck -f /dev/sdb1 e2fsck 1.42 (29-Nov-2011) The filesystem size (according to the superblock) is 610471680 blocks The physical size of the device is 536870911 blocks Either the superblock or the partition table is likely to be corrupt! Abort? n .... Error reading block 537395215 (Invalid argument) while reading inode and block bitmaps. Ignore error<y>? yes Force rewrite<y>? yes Error writing block 537395215 (Invalid argument) while reading inode and block bitmaps. Ignore error<y>? yes ... A lot of these. I can't use e2fsck -y because the first question aborts if I say "y". If I put a weight on the 'y' key it fails because none of the errors were really fixed. I asked this question before and tried using gparted but gparted fails because the first thing it does is: e2fsck -f -y -v /dev/sdb1 giving the same error. The disk status says healthy. There are no bad blocks. This is very frustrating because I can see the data in testdisk and it looks like it's all there. I already bought another 2.5tb drive and made a clone using dd. The next step if I can't fix this is to wipe that drive and just move the data with testdisk, but it seems certain folders will copy infinitely until the drive is full because of symlinks or errors so it's also a difficult option. sudo fdisk -l Disk /dev/sdb: 2500.5 GB, 2500495958016 bytes 255 heads, 63 sectors/track, 304001 cylinders, total 4883781168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 4096 bytes I/O size (minimum/optimal): 4096 bytes / 4096 bytes Disk identifier: 0x0005da5e Device Boot Start End Blocks Id System /dev/sdb1 * 2048 4294969342 2147483647+ 83 Linux sudo badblocks -b 4096 -n -o badfile /dev/sdb 610471680 536870911 badfile is empty I also tried changing the superblock with "fsck -b" but all of them are the same.

Read the article

CakePHP 3-level-deep model associatons

- by user357452

Read the article

web.xml not reloading in tomcat even after stop/start

- by ajay

This is in relation to:- http://stackoverflow.com/questions/2576514/basic-tomcat-servlet-error I changed my web.xml file, did ant compile , all, /etc/init.d/tomcat stop , start Even then my web.xml file in tomcat deployment is still unchanged. This is build.properties file:- app.name=hello catalina.home=/usr/local/tomcat manager.username=admin manager.password=admin This is my build.xml file. Is there something wrong with this:-    <project name="My Project" default="compile" basedir=".">   <property file="build.properties"/> <property file="${user.home}/build.properties"/>   <property name="app.name" value="myapp"/> <property name="app.path" value="/${app.name}"/> <property name="app.version" value="0.1-dev"/> <property name="build.home" value="${basedir}/build"/> <property name="catalina.home" value="../../../.."/>  <property name="dist.home" value="${basedir}/dist"/> <property name="docs.home" value="${basedir}/docs"/> <property name="manager.url" value="http://localhost:8080/manager"/> <property name="src.home" value="${basedir}/src"/> <property name="web.home" value="${basedir}/web"/>       <path id="compile.classpath">     <fileset dir="${catalina.home}/bin"> <include name="*.jar"/> </fileset> <pathelement location="${catalina.home}/lib"/> <fileset dir="${catalina.home}/lib"> <include name="*.jar"/> </fileset> </path>   <taskdef resource="org/apache/catalina/ant/catalina.tasks" classpathref="compile.classpath"/>   <property name="compile.debug" value="true"/> <property name="compile.deprecation" value="false"/> <property name="compile.optimize" value="true"/>   <target name="all" depends="clean,compile" description="Clean build and dist directories, then compile"/>   <target name="clean" description="Delete old build and dist directories"> <delete dir="${build.home}"/> <delete dir="${dist.home}"/> </target>   <target name="compile" depends="prepare" description="Compile Java sources">  <mkdir dir="${build.home}/WEB-INF/classes"/> <javac srcdir="${src.home}" destdir="${build.home}/WEB-INF/classes" debug="${compile.debug}" deprecation="${compile.deprecation}" optimize="${compile.optimize}"> <classpath refid="compile.classpath"/> </javac>  <copy todir="${build.home}/WEB-INF/classes"> <fileset dir="${src.home}" excludes="**/*.java"/> </copy> </target>   <target name="dist" depends="compile,javadoc" description="Create binary distribution">  <mkdir dir="${dist.home}/docs"/> <copy todir="${dist.home}/docs"> <fileset dir="${docs.home}"/> </copy>  <jar jarfile="${dist.home}/${app.name}-${app.version}.war" basedir="${build.home}"/>  </target>   <target name="install" depends="compile" description="Install application to servlet container"> <deploy url="${manager.url}" username="${manager.username}" password="${manager.password}" path="${app.path}" localWar="file://${build.home}"/> </target>   <target name="javadoc" depends="compile" description="Create Javadoc API documentation"> <mkdir dir="${dist.home}/docs/api"/> <javadoc sourcepath="${src.home}" destdir="${dist.home}/docs/api" packagenames="*"> <classpath refid="compile.classpath"/> </javadoc> </target>   <target name="list" description="List installed applications on servlet container"> <list url="${manager.url}" username="${manager.username}" password="${manager.password}"/> </target>   <target name="prepare">  <mkdir dir="${build.home}"/> <mkdir dir="${build.home}/WEB-INF"/> <mkdir dir="${build.home}/WEB-INF/classes"/>  <copy todir="${build.home}"> <fileset dir="${web.home}"/> </copy>   <mkdir dir="${build.home}/WEB-INF/lib"/>    </target>   <target name="reload" depends="compile" description="Reload application on servlet container"> <reload url="${manager.url}" username="${manager.username}" password="${manager.password}" path="${app.path}"/> </target>   <target name="remove" description="Remove application on servlet container"> <undeploy url="${manager.url}" username="${manager.username}" password="${manager.password}" path="${app.path}"/> </target> </project>

Read the article

Simple Self Join Query Bad Performance

- by user1514042

Could anyone advice on how do I improve the performance of the following query. Note, the problem seems to be caused by where clause. Data (table contains a huge set of rows - 500K+, the set of parameters it's called with assums the return of 2-5K records per query, which takes 8-10 minutes currently): USE [SomeDb] GO SET ANSI_NULLS ON GO SET QUOTED_IDENTIFIER ON GO CREATE TABLE [dbo].[Data]( [x] [money] NOT NULL, [y] [money] NOT NULL, CONSTRAINT [PK_Data] PRIMARY KEY CLUSTERED ( [x] ASC )WITH (PAD_INDEX = OFF, STATISTICS_NORECOMPUTE = OFF, IGNORE_DUP_KEY = OFF, ALLOW_ROW_LOCKS = ON, ALLOW_PAGE_LOCKS = ON) ON [PRIMARY] ) ON [PRIMARY] GO The Query select top 10000 s.x as sx, e.x as ex, s.y as sy, e.y as ey, e.y - s.y as y_delta, e.x - s.x as x_delta from Data s inner join Data e on e.x > s.x and e.x - s.x between xFrom and xTo --where e.y - s.y > @yDelta -- when uncommented causes a huge delay Update 1 - Execution Plan <?xml version="1.0" encoding="utf-16"?> <ShowPlanXML xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance" xmlns:xsd="http://www.w3.org/2001/XMLSchema" Version="1.2" Build="11.0.2100.60" xmlns="http://schemas.microsoft.com/sqlserver/2004/07/showplan"> <BatchSequence> <Batch> <Statements> <StmtSimple StatementCompId="1" StatementEstRows="100" StatementId="1" StatementOptmLevel="FULL" StatementOptmEarlyAbortReason="GoodEnoughPlanFound" StatementSubTreeCost="0.0263655" StatementText="select top 100
s.x as sx,
e.x as ex,
s.y as sy,
e.y as ey,
e.y - s.y as y_delta,
e.x - s.x as x_delta
from Data s 
 inner join Data e
 on e.x > s.x and e.x - s.x between 100 and 105
where e.y - s.y > 0.01
" StatementType="SELECT" QueryHash="0xAAAC02AC2D78CB56" QueryPlanHash="0x747994153CB2D637" RetrievedFromCache="true"> <StatementSetOptions ANSI_NULLS="true" ANSI_PADDING="true" ANSI_WARNINGS="true" ARITHABORT="true" CONCAT_NULL_YIELDS_NULL="true" NUMERIC_ROUNDABORT="false" QUOTED_IDENTIFIER="true" /> <QueryPlan DegreeOfParallelism="0" NonParallelPlanReason="NoParallelPlansInDesktopOrExpressEdition" CachedPlanSize="24" CompileTime="13" CompileCPU="13" CompileMemory="424"> <MemoryGrantInfo SerialRequiredMemory="0" SerialDesiredMemory="0" /> <OptimizerHardwareDependentProperties EstimatedAvailableMemoryGrant="52199" EstimatedPagesCached="14561" EstimatedAvailableDegreeOfParallelism="4" /> <RelOp AvgRowSize="55" EstimateCPU="1E-05" EstimateIO="0" EstimateRebinds="0" EstimateRewinds="0" EstimatedExecutionMode="Row" EstimateRows="100" LogicalOp="Compute Scalar" NodeId="0" Parallel="false" PhysicalOp="Compute Scalar" EstimatedTotalSubtreeCost="0.0263655"> <OutputList> <ColumnReference Database="[SomeDb]" Schema="[dbo]" Table="[Data]" Alias="[s]" Column="x" /> <ColumnReference Database="[SomeDb]" Schema="[dbo]" Table="[Data]" Alias="[s]" Column="y" /> <ColumnReference Database="[SomeDb]" Schema="[dbo]" Table="[Data]" Alias="[e]" Column="x" /> <ColumnReference Database="[SomeDb]" Schema="[dbo]" Table="[Data]" Alias="[e]" Column="y" /> <ColumnReference Column="Expr1004" /> <ColumnReference Column="Expr1005" /> </OutputList> <ComputeScalar> <DefinedValues> <DefinedValue> <ColumnReference Column="Expr1004" /> <ScalarOperator ScalarString="[SomeDb].[dbo].[Data].[y] as [e].[y]-[SomeDb].[dbo].[Data].[y] as [s].[y]"> <Arithmetic Operation="SUB"> <ScalarOperator> <Identifier> <ColumnReference Database="[SomeDb]" Schema="[dbo]" Table="[Data]" Alias="[e]" Column="y" /> </Identifier> </ScalarOperator> <ScalarOperator> <Identifier> <ColumnReference Database="[SomeDb]" Schema="[dbo]" Table="[Data]" Alias="[s]" Column="y" /> </Identifier> </ScalarOperator> </Arithmetic> </ScalarOperator> </DefinedValue> <DefinedValue> <ColumnReference Column="Expr1005" /> <ScalarOperator ScalarString="[SomeDb].[dbo].[Data].[x] as [e].[x]-[SomeDb].[dbo].[Data].[x] as [s].[x]"> <Arithmetic Operation="SUB"> <ScalarOperator> <Identifier> <ColumnReference Database="[SomeDb]" Schema="[dbo]" Table="[Data]" Alias="[e]" Column="x" /> </Identifier> </ScalarOperator> <ScalarOperator> <Identifier> <ColumnReference Database="[SomeDb]" Schema="[dbo]" Table="[Data]" Alias="[s]" Column="x" /> </Identifier> </ScalarOperator> </Arithmetic> </ScalarOperator> </DefinedValue> </DefinedValues> <RelOp AvgRowSize="39" EstimateCPU="1E-05" EstimateIO="0" EstimateRebinds="0" EstimateRewinds="0" EstimatedExecutionMode="Row" EstimateRows="100" LogicalOp="Top" NodeId="1" Parallel="false" PhysicalOp="Top" EstimatedTotalSubtreeCost="0.0263555"> <OutputList> <ColumnReference Database="[SomeDb]" Schema="[dbo]" Table="[Data]" Alias="[s]" Column="x" /> <ColumnReference Database="[SomeDb]" Schema="[dbo]" Table="[Data]" Alias="[s]" Column="y" /> <ColumnReference Database="[SomeDb]" Schema="[dbo]" Table="[Data]" Alias="[e]" Column="x" /> <ColumnReference Database="[SomeDb]" Schema="[dbo]" Table="[Data]" Alias="[e]" Column="y" /> </OutputList> <RunTimeInformation> <RunTimeCountersPerThread Thread="0" ActualRows="100" ActualEndOfScans="1" ActualExecutions="1" /> </RunTimeInformation> <Top RowCount="false" IsPercent="false" WithTies="false"> <TopExpression> <ScalarOperator ScalarString="(100)"> <Const ConstValue="(100)" /> </ScalarOperator> </TopExpression> <RelOp AvgRowSize="39" EstimateCPU="151828" EstimateIO="0" EstimateRebinds="0" EstimateRewinds="0" EstimatedExecutionMode="Row" EstimateRows="100" LogicalOp="Inner Join" NodeId="2" Parallel="false" PhysicalOp="Nested Loops" EstimatedTotalSubtreeCost="0.0263455"> <OutputList> <ColumnReference Database="[SomeDb]" Schema="[dbo]" Table="[Data]" Alias="[s]" Column="x" /> <ColumnReference Database="[SomeDb]" Schema="[dbo]" Table="[Data]" Alias="[s]" Column="y" /> <ColumnReference Database="[SomeDb]" Schema="[dbo]" Table="[Data]" Alias="[e]" Column="x" /> <ColumnReference Database="[SomeDb]" Schema="[dbo]" Table="[Data]" Alias="[e]" Column="y" /> </OutputList> <RunTimeInformation> <RunTimeCountersPerThread Thread="0" ActualRows="100" ActualEndOfScans="0" ActualExecutions="1" /> </RunTimeInformation> <NestedLoops Optimized="false"> <OuterReferences> <ColumnReference Database="[SomeDb]" Schema="[dbo]" Table="[Data]" Alias="[e]" Column="x" /> <ColumnReference Database="[SomeDb]" Schema="[dbo]" Table="[Data]" Alias="[e]" Column="y" /> </OuterReferences> <RelOp AvgRowSize="23" EstimateCPU="1.80448" EstimateIO="3.76461" EstimateRebinds="0" EstimateRewinds="0" EstimatedExecutionMode="Row" EstimateRows="1" LogicalOp="Clustered Index Scan" NodeId="3" Parallel="false" PhysicalOp="Clustered Index Scan" EstimatedTotalSubtreeCost="0.0032831" TableCardinality="1640290"> <OutputList> <ColumnReference Database="[SomeDb]" Schema="[dbo]" Table="[Data]" Alias="[e]" Column="x" /> <ColumnReference Database="[SomeDb]" Schema="[dbo]" Table="[Data]" Alias="[e]" Column="y" /> </OutputList> <RunTimeInformation> <RunTimeCountersPerThread Thread="0" ActualRows="15225" ActualEndOfScans="0" ActualExecutions="1" /> </RunTimeInformation> <IndexScan Ordered="false" ForcedIndex="false" ForceScan="false" NoExpandHint="false"> <DefinedValues> <DefinedValue> <ColumnReference Database="[SomeDb]" Schema="[dbo]" Table="[Data]" Alias="[e]" Column="x" /> </DefinedValue> <DefinedValue> <ColumnReference Database="[SomeDb]" Schema="[dbo]" Table="[Data]" Alias="[e]" Column="y" /> </DefinedValue> </DefinedValues> <Object Database="[SomeDb]" Schema="[dbo]" Table="[Data]" Index="[PK_Data]" Alias="[e]" IndexKind="Clustered" /> </IndexScan> </RelOp> <RelOp AvgRowSize="23" EstimateCPU="0.902317" EstimateIO="1.88387" EstimateRebinds="1" EstimateRewinds="0" EstimatedExecutionMode="Row" EstimateRows="100" LogicalOp="Clustered Index Seek" NodeId="4" Parallel="false" PhysicalOp="Clustered Index Seek" EstimatedTotalSubtreeCost="0.0263655" TableCardinality="1640290"> <OutputList> <ColumnReference Database="[SomeDb]" Schema="[dbo]" Table="[Data]" Alias="[s]" Column="x" /> <ColumnReference Database="[SomeDb]" Schema="[dbo]" Table="[Data]" Alias="[s]" Column="y" /> </OutputList> <RunTimeInformation> <RunTimeCountersPerThread Thread="0" ActualRows="100" ActualEndOfScans="15224" ActualExecutions="15225" /> </RunTimeInformation> <IndexScan Ordered="true" ScanDirection="FORWARD" ForcedIndex="false" ForceSeek="false" ForceScan="false" NoExpandHint="false" Storage="RowStore"> <DefinedValues> <DefinedValue> <ColumnReference Database="[SomeDb]" Schema="[dbo]" Table="[Data]" Alias="[s]" Column="x" /> </DefinedValue> <DefinedValue> <ColumnReference Database="[SomeDb]" Schema="[dbo]" Table="[Data]" Alias="[s]" Column="y" /> </DefinedValue> </DefinedValues> <Object Database="[SomeDb]" Schema="[dbo]" Table="[Data]" Index="[PK_Data]" Alias="[s]" IndexKind="Clustered" /> <SeekPredicates> <SeekPredicateNew> <SeekKeys> <EndRange ScanType="LT"> <RangeColumns> <ColumnReference Database="[SomeDb]" Schema="[dbo]" Table="[Data]" Alias="[s]" Column="x" /> </RangeColumns> <RangeExpressions> <ScalarOperator ScalarString="[SomeDb].[dbo].[Data].[x] as [e].[x]"> <Identifier> <ColumnReference Database="[SomeDb]" Schema="[dbo]" Table="[Data]" Alias="[e]" Column="x" /> </Identifier> </ScalarOperator> </RangeExpressions> </EndRange> </SeekKeys> </SeekPredicateNew> </SeekPredicates> <Predicate> <ScalarOperator ScalarString="([SomeDb].[dbo].[Data].[x] as [e].[x]-[SomeDb].[dbo].[Data].[x] as [s].[x])>=($100.0000) AND ([SomeDb].[dbo].[Data].[x] as [e].[x]-[SomeDb].[dbo].[Data].[x] as [s].[x])<=($105.0000) AND ([SomeDb].[dbo].[Data].[y] as [e].[y]-[SomeDb].[dbo].[Data].[y] as [s].[y])>(0.01)"> <Logical Operation="AND"> <ScalarOperator> <Compare CompareOp="GE"> <ScalarOperator> <Arithmetic Operation="SUB"> <ScalarOperator> <Identifier> <ColumnReference Database="[SomeDb]" Schema="[dbo]" Table="[Data]" Alias="[e]" Column="x" /> </Identifier> </ScalarOperator> <ScalarOperator> <Identifier> <ColumnReference Database="[SomeDb]" Schema="[dbo]" Table="[Data]" Alias="[s]" Column="x" /> </Identifier> </ScalarOperator> </Arithmetic> </ScalarOperator> <ScalarOperator> <Const ConstValue="($100.0000)" /> </ScalarOperator> </Compare> </ScalarOperator> <ScalarOperator> <Compare CompareOp="LE"> <ScalarOperator> <Arithmetic Operation="SUB"> <ScalarOperator> <Identifier> <ColumnReference Database="[SomeDb]" Schema="[dbo]" Table="[Data]" Alias="[e]" Column="x" /> </Identifier> </ScalarOperator> <ScalarOperator> <Identifier> <ColumnReference Database="[SomeDb]" Schema="[dbo]" Table="[Data]" Alias="[s]" Column="x" /> </Identifier> </ScalarOperator> </Arithmetic> </ScalarOperator> <ScalarOperator> <Const ConstValue="($105.0000)" /> </ScalarOperator> </Compare> </ScalarOperator> <ScalarOperator> <Compare CompareOp="GT"> <ScalarOperator> <Arithmetic Operation="SUB"> <ScalarOperator> <Identifier> <ColumnReference Database="[SomeDb]" Schema="[dbo]" Table="[Data]" Alias="[e]" Column="y" /> </Identifier> </ScalarOperator> <ScalarOperator> <Identifier> <ColumnReference Database="[SomeDb]" Schema="[dbo]" Table="[Data]" Alias="[s]" Column="y" /> </Identifier> </ScalarOperator> </Arithmetic> </ScalarOperator> <ScalarOperator> <Const ConstValue="(0.01)" /> </ScalarOperator> </Compare> </ScalarOperator> </Logical> </ScalarOperator> </Predicate> </IndexScan> </RelOp> </NestedLoops> </RelOp> </Top> </RelOp> </ComputeScalar> </RelOp> </QueryPlan> </StmtSimple> </Statements> </Batch> </BatchSequence> </ShowPlanXML>

Read the article

MS Ajax Libraries and Configured Assemblies

- by smehaffie

Use Case You have a brand new IIS servers that has .Net 3.5 installed and are migrating sites to the new servers. In the process of migrating sites you come across some sites that get an error about the version of AJAX libraries being references in the web.config. In the web.config all the entries reference 1.0.61025.0, but the older version of the AJAX libraries are not installed on the new servers, only the latest version is installed that comes with .Net 3.5. So what are the options to fix this issue. Solutions 1) Install the older version of the AJAX Libraries: Although this works, IMO it is never a great idea to install an older version of a library after a newer version has been installed. Plus, if all new application use the latest versions, is it worth the effort of installing the older version for a few legacy applications? 2) Update the web.config files so all references use latest version (3.5.0.0): This option is very time consuming and error prone. In addition, you will also have to update any pages where there is a register tag for the older libraries as well. This would require you to redeploy any application that have this issue. 3) Use the Configured Assembly capabilities of .Net (aka: Assembly Bindings) to make any application that uses the older AJAX libraries to use the new AJAX libraries. IMO, this is the easiest, quickest and least invasive way to fix the issue. Below are the steps to implement this fix. Solution #3 Do the following steps on the IIS servers that the issue is occurring. The 2 assemblies that need assemblies bindings created are: System.Web.Extension & System.Web.Extensions.Design 1) Go to Start - > All Program -> Administrative Tools -> Microsoft .NET Framework 2.0 Configuration. 2) Right click on "Configured Assemblies" to view list of configured assemblies. 3) Left Click on right pane to bring up menu and choose "Add". 4) Make sure "Choose and assembly from the assembly cache is checked" and click the "Choose Assembly" button. 5) Choose System.Web.Extension (does not matter what version). 6) Click the "Finish" button. 7) Binding Policy Tab - Enter Requested Version = 1.0.61025.0 - Enter New Version = 3.5.0.0 8) Repeat steps 2-7 for the System.Web.Extensions.Design assembly. --------------------------------------------------------------------------------------------------------------------------------------------------------- Note: If "Microsoft .NET Framework 2.0 Configuration does not exist under Admin tools use mmc to access it (see below) 1) Start -> Run -> Enter MMC 2) File - > Add/Remove Snap-In then Click "Add" button 3) Choose ".Net 2.0 Configuration" then click "Add" button and then the "Close" Button. 4) On "Add/Remove Snapin" windows click the "OK" Button. 5) Expand the tree on the right and you can start following the directions above for adding the configured assemblies. ---------------------------------------------------------------------------------------------------------------------------------------------------------

Search Results

Search found 6103 results on 245 pages for 'logical tree'.

Page 201/245 | < Previous Page | 197 198 199 200 201 202 203 204 205 206 207 208 | Next Page >

- by Hello71

- by netmikey

- by wuckachucka

- by Cyril N.

- by Jeff Atwood

- by bbalegere

- by ewwhite

- by Backtogeek

- by HisDudeness

- by John C

- by Janar

- by George

- by Shoshomiga

- by widgisoft

- by Shoshomiga

- by kyrpas

- by Enigma

- by karthik

- by user318772

- by gkb0986

- by BreezyChick89

- by user357452

- by ajay

- by user1514042

- by smehaffie

< Previous Page | 197 198 199 200 201 202 203 204 205 206 207 208 | Next Page >