Search Results

Search found 19676 results on 788 pages for 'setup cd'.

Page 201/788 | < Previous Page | 197 198 199 200 201 202 203 204 205 206 207 208  | Next Page >

• My WD Caviar Green SATA HDD cannot be detected

  - by obhasha

  I have a WD 2TB Caviar Green SATA HDD. I used it as an external hard drive formatted to FAT32. The main purpose was to store my PS3 games. It worked fine and all of a sudden my PS3 stopped detecting it. I tried connecting it to my pc and the same result. I took it off from the enclosure and plugged it directly to my PC and used the BIOS setup. The BIOS setup detects my HDD but it says it's 0.0MB!!! I also tried the WD Data Lifeguard Diagnostic tool and it wasn't much of use because the drive is not picking up by windows at all. Is my HDD dead? Is it beyond repair?

  Read the article

• Raid recovery in gigabyte GA-8I945 Pro

  - by epeleg

  This was a working machine until a few days ago. And now it won't boot into the OS, during startup if makes clicking sounds (I think from one of the drives). Installed OS: Windows 2003 Web edition Hardware: Gigabyte GA-8I945P Pro , 2*160G Sata in RAID1 configuration , 2 Volumes – 25G and the rest. When I installed windows on it, during setup, I pressed F6 and used ICH7DH drivers of RAID. The manual for the MOBO says: Step 1: After the POST memory test begins and before the operating system boot begins, look for a message which says "Press to enter Configuration utility" (Figure 4). Press CTRL+ I to enter the RAID BIOS setup utility. But the machine never shows this message. BIOS SATA RAID/AHCI Mode is set to RAID. Any ideas or pointers on what I can do to recover my data? Thanks

  Read the article

• Remote access to internal machine (ssh port-forwarding)

  - by MacUsers

  I have a server (serv05) at work with a public ip, hosting two KVM guests - vtest1 & vtest2 - in two different private network - 192.168.122.0 & 192.168.100.0 - respectively, this way: [root@serv05 ~]# ip -o addr show | grep -w inet 1: lo inet 127.0.0.1/8 scope host lo 2: eth0 inet xxx.xxx.xx.197/24 brd xxx.xxx.xx.255 scope global eth0 4: virbr1 inet 192.168.100.1/24 brd 192.168.100.255 scope global virbr1 6: virbr0 inet 192.168.122.1/24 brd 192.168.122.255 scope global virbr0 # [root@serv05 ~]# route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 192.168.100.0 0.0.0.0 255.255.255.0 U 0 0 0 virbr1 xxx.xxx.xx.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0 192.168.122.0 0.0.0.0 255.255.255.0 U 0 0 0 virbr0 169.254.0.0 0.0.0.0 255.255.0.0 U 1002 0 0 eth0 0.0.0.0 xxx.xxx.xx.62 0.0.0.0 UG 0 0 0 eth0 I've also setup IP FORWARDing and Masquerading this way: iptables --table nat --append POSTROUTING --out-interface eth0 -j MASQUERADE iptables --append FORWARD --in-interface virbr0 -j ACCEPT All works up to this point. If I want to remote access vtest1 (or vtest2) first I ssh to serv05 and then from there ssh to vtest1. Is there a way to setup a port forwarding so that vtest1 can be accessed directly from the outside world? This is what I probably need to setup: external_ip (tcp port 4444) -> DNAT -> 192.168.122.50 (tcp port 22) I know it's easily do'able using a SOHO router but can't figure out how can I do that on a Linux box. Any help form you guys?? Cheers!! Update: 1 Now I've made ssh to listen to both of the ports: [root@serv05 ssh]# netstat -tulpn | grep ssh tcp 0 0 xxx.xxx.xx.197:22 0.0.0.0:* LISTEN 5092/sshd tcp 0 0 xxx.xxx.xx.197:4444 0.0.0.0:* LISTEN 5092/sshd and port 4444 is allowed in the iptables rules: [root@serv05 sysconfig]# grep 4444 iptables -A PREROUTING -i eth0 -p tcp -m tcp --dport 4444 -j DNAT --to-destination 192.168.122.50:22 -A INPUT -p tcp -m state --state NEW -m tcp --dport 4444 -j ACCEPT -A FORWARD -i eth0 -p tcp -m tcp --dport 4444 -j ACCEPT But I'm getting connection refused: maci:~ santa$ telnet serv05 4444 Trying xxx.xxx.xx.197... telnet: connect to address xxx.xxx.xx.197: Connection refused telnet: Unable to connect to remote host Any idea what's I'm still missing? Cheers!!

  Read the article

• VPN Connection Causes Internal LAN Connection Loss with Server

  - by sleepisfortheweak

  I've tried configuring basic PPTP VPN at my small business using a number of different tutorials. As far as I can tell, the actual VPN connection worked fine, but upon connecting a client, the Server 'disappears' from the internal LAN. The RRAS service must be stopped before the connection is restored. My Setup: The network is simply a DSL Gateway/Router to the outside functioning as NAT/Firewall/DHCP. The server is a Win Server 2008 machine at fixed IP 192.168.1.200. The server has 1 NIC, so I used the 'custom' option when configuring RRAS. The RRAS settings should be default except that I've disabled ports for connection types I'm not using and reduced PPTP ports to 10. I've also created an address pool and disabled DHCP packet forwarding. The server only functions as a File Share and now a VPN Server. Local LAN computers all have mapped network shares to the server authenticated based on Local User/Group setup on the server. The Problem: The moment a client connects through VPN, the server 'disappears' from the local network. All mapped drives disconnect and there is no response to a ping 192.168.1.200. Even if the client disconnects, the server does not re-appear at that address until the RRAS service is stopped. I've Tried: Using an Address Pool inside and outside the local subnet. Using DCHP Relay Checking Inbound/Outbound filters (none enabled) The fact that nothing I've tried has had any effect, and that I can connect and successfully obtain an IP tells me that it's something more fundamental I'm missing. My gut tells me that it's something to do with the second IP address added by the VPN client somehow taking over the interface or traffic from the local LAN accidently getting routed to the VPN client instead of handled at the server once RRAS has become 'active' when a client connects. Hopefully this may be obvious to someone with real IT experience. I've been doing this a while and almost never been stumped. I'm starting to think it might actually be something tricky since my setup is pretty basic yet refuses to work. I'll be happy to include more info if this doesn't ring any bells right away for anyone. Thanks

  Read the article

• windows cache not working as it should?

  - by piotrektt

  I run windows 2012 server with data center. The setup is with 60GB of RAM. I have one file shared on VHD and when I copy this file locally the RAM cache is all used up but when multiple computers connect to the share it the cache is not used. The network is 8Gb. The whole network is around 200 computers that need to read that one file but on this setup only 10 connection kills the server. Is there any way to check what is going on? What other solution can I use to manage cache in windows?

  Read the article

• How do I solve this "unexpected '}' syntax error" in my bash script?

  - by WASasquatch

  I have a piece of code that has some serious issues and I was hoping to get it solved soon but no one has offered any help. I thought I'd try some Ubuntu users since this is the OS running the script. mc_addplugin() { if pgrep -u $USERNAME -f $SERVICE > /dev/null then echo "$SERVICE is running! Please stop the service before adding a plugin." else echo "Paste the URL to the .JAR Plugin..." read JARURL JARNAME=$(basename "$JARURL") if [ -d "$TEMPPLUGINS" ] then as_user "cd $PLUGINSPATH && wget -r -A.jar $JARURL -o temp_plugins/$JARNAME" else as_user "cd $PLUGINSPATH && mkdir $TEMPPLUGINS && wget -r -A.jar $JARURL -o temp_plugins/$JARNAME" fi if [ -f "$TMPDIR/$JARNAME" ] then if [ -f "$PLUGINSPATH/$JARNAME" ] then if `diff $PLUGINSPATH/$JARNAME $TMPDIR/$JARNAME >/dev/null` then echo "You are already running the latest version of $JARNAME." else NOW=`date "+%Y-%m-%d_%Hh%M"` echo "Are you sure you want to overwrite this plugin? [Y/n]" echo "Note: Your old plugin will be moved to the "$TEMPPLUGINS" folder with todays date." select yn in "Yes" "No"; do case $yn in Yes ) as_user "mv $PLUGINSPATH/$JARNAME $TEMPPLUGINS/${JARNAME}_${NOW} && mv $TEMPPLUGINS/$JARNAME $PLUGINSPATH/$JARNAME"; break;; No ) echo "The plugin has not been installed! Removing temporary plugin and exiting..." as_user "rm $TEMPPLUGINS/$JARNAME"; exit;; esac done echo "Would you like to start the $SERVICE now? [Y/n]" select yn in "Yes" "No"; do case $yn in Yes ) mc_start; break;; No ) "$SERVICE not running! To start the service run: /etc/init.d/craftbukkit start"; exit;; esac done fi else echo "Are you sure you want to add this new plugin? [Y/n]" select yn in "Yes" "No"; do case $yn in Yes ) as_user "mv $PLUGINSPATH/$JARNAME $TEMPPLUGINS/${JARNAME}_${NOW} && mv $TEMPPLUGINS/$JARNAME $PLUGINSPATH/$JARNAME"; break;; No ) echo "The plugin has not been installed! Removing temporary plugin and exiting..." as_user "rm $TEMPPLUGINS/$JARNAME"; exit;; esac done echo "Would you like to start the $SERVICE now? [Y/n]?" select yn in "Yes" "No"; do case $yn in Yes ) mc_start; break;; No ) "$SERVICE not running! To start the service run: /etc/init.d/craftbukkit start"; exit;; esac done fi else echo "Failed to download the plugin from the URL you specified!" exit; fi } It throws it at the closing bracket at the end of the function.

  Read the article

• Cheapest High Available Web Server [closed]

  - by xyz

  I would like to create a high-available setup (e.g. a small cluster) for a webserver, i.e. it will run Apache, PHP and MySQL. There will be between 2-8 small websites running with only very little traffic and workload. High availability is however very important. I don't want to be dependent on 1 datacenter, so there must be a minimum of 2 servers placed in different datacenters, and if one server goes down, the user must experience no or only a minimum of downtime - and no data loss. I have considered Amazon AWS using their Elastic Load Balancing, since it is possible to buy 2 EC2 instances in 2 availability zones and set up load balancing and RDS (Multi-AZ). However this seems rather expensive. Using the AWS price calculator http://calculator.s3.amazonaws.com/calc5.html it totals to 185$/month the first year (including the free tier). Are my calculations incorrect or is there a cheaper way to make this HA setup? Best regards

  Read the article

• Amazon EC2 firewall rules & VPN connections

  - by John

  I'm moving from Rackspace to Amazon EC2. One thing I like about our Rackspace setup is that it is extremely secure. The MySQL box can only be accessed via internal IPs, and we have a Cisco VPN firewall that allows us to dial in remotely and access port 3306 as though we were on the internal network. I'd like to figure out how to replicate this setup with EC2. How can I make the MySQL box so that port 3306 can only be accessed on the internal network? What about the VPN piece of things? I know Amazon has the VPC service, but it seems like that's for the purpose of connecting to an existing network. I don't have an existing network. I want to essentially create one inside Amazon and connect to that. What are my options? Any good tutorials on how to get started? Thanks in advance for your help

  Read the article

• Just how slow should my VPN be?

  - by David Heggie

  I have a VPN setup between a remote office with 2 ADSL connections (8Mb downstream, 512Kb upstream) and a main office with a 10Mb EFM connection (10Mb both up and down). The VPN is an IPSec connection using a DrayTek 2930 router for the ADSL and a DrayTek 3200 router at the EFM end. However, I'm unable to get speeds over this connection (tested with iperf) of anything over 600Kb or so down from the main office (traffic will pretty much always be from the main office to the remote office) Whilst I realise that there is an overhead and I'm never going to get the "full" bandwidth available over this VPN, I'd like to think that there's something I should be looking at that may help improve it. I've tried using the DrayTek's built-in "VPN Trunking" features which are supposed to load-balance connections, but this doesn't seem to improve matters much. I guess my question is - is this the kind of performance I should expect from this kind of setup and I'll just have to live with it, or should I be able to squeeze something more out of it through some VPN magic?

  Read the article

• Feedback on available mid-to-enterprise level desktop backup solutions [closed]

  - by user85610

  I am involved in the creation of a new backup solution to replace our current Retrospect setup, which has become a significant time sink to administer. We have almost 200 desktop and some laptop clients, both Windows and OS X. We're only interested in products oriented around disk-to-disk, and would be integrate well with our current set of nine NAS devices as target storage. I'd just like some feedback from anyone out there, as it's sometimes difficult otherwise to find objective reviews of software at this level. Both data and time are important enough that we need a reliable solution which won't be prone to self-destruction as often as Retrospect. Bonus points for de-duplication, which might help squeeze more service time out of our NAS setup in terms of capacity. Currently considering Commvault and Netbackup. Many other products I've seen don't have an OSX client. Any thoughts?

  Read the article

• Network Role based routing

  - by Steve Butler

  Apologies my networking skills are a tad rusty. I'm looking for a way to setup a system that gives me the ability to setup Role-based access to specific network resources. For example, i have three private subnets for specific groups, users will need access to one one or more subnets. I'd like to have all client machines on the same subnet/vlan, and then use 802.1x to authorize into a router(NAC device/whatever), the router would then see what user had authenticated(huge plus if it could determine AD group), and then allow routing to one or more of the three private subnets based upon their group membership. I've looked at packetFence, and it appears to work by assigning a client to a VLAN, but i'd still need a way to route some users into different back-end networks.

  Read the article

• Material to use for computer system cover against UV and salty air?

  - by hippietrail

  I live right next to the sea and have a large window quite close to my computer setup which allows a lot of indirect sunlight to enter. I'd like to buy or make a cover for my computer system. From visiting my usual mom & pop computer shop yesterday I got the impression these might not really exist any more. If I make my own I need a material with these qualities: Block or reduce ultraviolet light which can depolymerize plastics (the sun here in Australia is much stronger than in the northern hemisphere). Block salt-laden sea air which can oxidize USB and other connectors. Not cause static electricity when covering or uncovering. Keep dust off of course (-: My setup is a laptop plugged into a wide-screen LCD with a few external drives. So I think I'd want a largish sheet to flop over the whole desk. Are such covers commonly sold these days? What material(s) should I look for which provides the listed attributes?

  Read the article

• One bigger Virtual Machine distributed across many Nodes [on hold]

  - by flyer

  I just setup virtual machines on one hardware with Vagrant (this is just a test environment, not production!). I want to use a Puppet to configure them and next try to setup OpenStack. I am not sure If I am understanding how this should look at the end. Is it possible to have below architecture with OpenStack after all where I will run one Virtual Machine with Linux? ------------------------------- | VM | ------------------------------- | NOVA | NOVA | NOVA | ------------------------------- | OpenStack | ------------------------------- | Node | Node | Node | ------------------------------- (In my environment Nodes are just virtual machines, but my question concerns separate Hardware nodes) After some comments... Is it a language barrier, or? This is only my 'virtual environment'. If we imagine this virtual machines are a separate Nodes (e.g. every has 4 cores) the OpenStack is still the same, right? Can I run one Virtual Machine across many Nodes with OpenStack? Is it possible to aggregate the computation power of separate machines in one virtual distributed operating system?

  Read the article

• ASUS P5B Plus motherboard - no any drives found - how to restore RAID array?

  - by Moha

  We have a small server machine with an ASUS P5B Plus motherboard and 4 SATA HDDs. The HDDs were configured in a RAID10 array. Up until now, everything worked fine, but now the system doesn't recognize the drives. BIOS is set to RAID, jMicron controller is set to RAID, yet I can't see any of the drives in the BIOS setup, and jMicron BIOS tells me "no any drives found" The HDDs all spin up, I hear no clicking sounds or anything that would suggest HDD error. I did a search on this problem and replaced the SATA cables as suggested, but nothing's changed. What I have in mind is checking the CMOS battery and resetting the BIOS to use IDE mode, but I don't know if it will ruin the RAID system on the HDDs. It is not a critical server and there's only one database running on it (which I have backup of), but I don't want to setup the server from scratch if not necessary. What should I try to restore the RAID array and put the server back to working order?

  Read the article

• SSRS report on SharePoint Web Part

  - by MicroSumol

  I have this configuration: DBK- SQL/SSRS/SSAS (includes SharePoint databases) SPK- SharePoint I created a SharePoint Site with an SSL certificate. Then on DBK I setup the SSRS with an SSL. Finaly went back to SharePoint and setup a webpart on a subsite to connect to the SSRS report. The problem comes that the user is asked 2 times to authenticate. Once when he logs into sharepoint, then when he wants to see the SSRS report. Since I am not an expert on SSRS, I am asking is there an easy way to pass the SharePoint credentials to the SSRS report. Would it be easier to install SSRS on SPK? Would that even work or solve my problem?

  Read the article

• How do I get a Dell Latitude e6420 working?

  - by David_G

  I've just installed Ubuntu 12.04 (64-bit) on a brand new Dell Latitude e6420, and I'm having a few problems. This laptop has an Optimus (?) setup - i.e. integrated gfx and an Nvidia Quadro NVS 4200M. First problem - I ran setup, etc, and discovered that I can only run unity2d - If I try and login with unity3d, it just defaults to 2d. This is with nvidia-current installed (302.07). Note also that I can't run nvidia-settings ("You do not appear to be using the NVIDIA X driver."), and there is no additional drivers found ("No proprietary drivers are in use on this system"). I tried to troubleshoot this, and removed nvidia, leaving (I guess) just Nouveau drivers - In that case, unity3d did work, but I was stuck with the open source Nouveau drivers powering the integrated graphics. So, obviously, I want to run unity3d, and be using the more powerful Nvidia graphics card. I've tried a bit of tinkering around, but I'm not sure the best way to proceed, or perhaps more importantly, I'm not sure of what the best final solution might be. I've heard about bumblebee - but frankly, I would prefer to have the proprietary Nvidia drivers working properly. Any help would be much appreciated!

  Read the article

• Extend university wifi network [migrated]

  - by asfasdoiuh ouhouhouh

  i live in a university campus and i can get wifi signal on the outside of my window but not in the house. The solution i use at the moment is a usb wifi dongle outside connected to my laptop but the lack of an internal antenna make the connection quite unreliable at times. So i was trying to find another solution to improve the reception of my network. One idea is to setup a router on the outside (in a place with stronger signal) and redirect the connection inside the house with an ethernet cable but the problem is that our Uni Wifi is managed by a capitve portal (BlueSocket with DNS redirection to login page) and the authentication has to happen on the mac address that connect to the net (so the client appliance in this case). If I use a router with Mac-Clone capability i will be able to be redirected trough the captive portal on my laptop computer and login from there or i need to setup my router to fill in the login page by itself? There are other hardware/software solutions i can use to get what i want? Thank you all

  Read the article

• Why are the external IP of my router not the same as the external IP of my computer

  - by Martin

  I have a standard network setup where all my network devices, both WIFI and ethernet, are connected to the same router. Lately, however, I've been experiencing some very strange behavior. It started as a simple connecting error, when I tried to reach an FTP server using the external IP. Of course I went right into one of those CheckMyIP sites, to double check the IP and it turned out to be correct. Then I went into my router setup, which is through a tool called aiport-tool, because I have an Apple Aiport Extreme router. Turns out the router displays a different external IP, and for some reason that external IP works when I try to access the FTP server. Can anyone explain what is going on? Why are the devices connected to the router displaying an incorrect external IP? BTW i have no VPN/proxy setups on any of my devices.

  Read the article

• Create and manage child name servers (glue records) within my domain?

  - by basilmir

  Preface I use a top level domain provider that only allows me to add "normal" third-party name servers (a list where i can add "ns1.hostingcompany.com" type entries... nothing else) AND "child name servers" which i can later attach to my parent account ( ns1.myowndomain.com and an ip address). They do not provide other means of linking up. I want to host my own server and dns, even with just one name server (at first). My setup: Airport Extreme - get's a static ip address from my ISP Mac Mini Server - sits behind the Airport and get's a 10.0.1.2 My problem is that i can't seem to configure DNS correctly. I added a "child nameserver" with my airport's external static ip address at the top level provider, so to my understanding i should have all DNS traffic redirected to my Airport. I've opened port 53 UDP to let the traffic in. Now, what i don't get is this. My Mini Server is sitting on a 10.0.1.2 address and i have setup dns correctly, with an A record to point and resolve my server AND a reverse lookup to that 10.0.1.2. So it's ok for "internal stuff". Here is the clicker... How, when a request comes from the exterior for a reverse lookup, does the server "know" ... well look i have everything in 10.0.1.2 but the guy outside needs something from my real address. I can't begin to describe the MX record bonanza... How do i set this "right"? Do i "need" my Mini Server to sit on the external address directly (i can see how this could be the preferred solution, being close to a "real" server i have in my mind). If not... do i need a PTR record on the 10.0.1.2 server but with the external address in there? My dream: I will extend this "setup" with multiple Mini's in different cities where i work. I want a distributed something (Xgrid comes to mind). PS. Be gentle, i've read 2 books and the subject, and bought both the Lynda Essentials and DNS and Networking to boot, still i'm far from being on top of things.

  Read the article

• Setting Up Customer-Specific Domains

  - by GregT

  I can go to Fog Creek's web site, setup a new account, and they will instantly assign me a URL such as 'mycompany.fogbugz.com' (where 'mycompany' is something I make up, as opposed to some value assigned by Fog Creek). I can do the same type of thing with Beanstalk and many other vendors. I have been Googling around trying to figure out exactly how this works. 1: In the above example, is 'mycompany.fogbugz.com' set up in DNS in some special way other than how one would setup a vanilla 'www.foo.com' domain? 2: Assuming Fog Creek uses Tomcat (which I am sure is NOT true, but pretend it is) would they be likely to have created a tomcat/webapps/mycompany subdirectory on their server? Or is there some simpler way to handle this? I'm obviously not a DNS or TC wizard. Any insight appreciated. Happy New Year!

  Read the article

• Need help understanding Mocks and Stubs

  - by Theomax

  I'm new to use mocking frameworks and I have a few questions on the things that I am not clear on. I'm using Rhinomocks to generate mock objects in my unit tests. I understand that mocks can be created to verify interactions between methods and they record the interactions etc and stubs allow you to setup data and entities required by the test but you do not verify expectations on stubs. Looking at the recent unit tests I have created, I appear to be creating mocks literally for the purpose of stubbing and allowing for data to be setup. Is this a correct usage of mocks or is it incorrect if you're not actually calling verify on them? For example: user = MockRepository.GenerateMock<User>(); user.Stub(x => x.Id = Guid.NewGuid()); user.Stub(x => x.Name = "User1"); In the above code I generate a new user mock object, but I use a mock so I can stub the properties of the user because in some cases if the properties do not have a setter and I need to set them it seems the only way is to stub the property values. Is this a correct usage of stubbing and mocking? Also, I am not completely clear on what the difference between the following lines is: user.Stub(x => x.Id).Return(new Guid()); user.Stub(x => x.Id = Guid.NewGuid());

  Read the article

• Make Outlook run rules on non-inbox folders automatically

  - by tHeSiD

  I currently have my Outlook setup with Gmail. I have a couple of rules that I have defined which run on different folders (lables) in my account. I have filters already setup in GMail which will make emails skip the inbox and put them in the respective folders. Whenever I get a new email, in those folders, my rules are not run (they are just for setting categories). I have to run them manually. I think its because the emails don't come to the inbox first but directly into the folder. Is there anyway to make outlook run rules automatically on those folders? A scheduled run should also be fine.

  Read the article

• Printer Canon MP540 succesfully added finally but doesn't print? (Attached Debug log)

  - by NES

  i tried to setup my printer in Ubuntu 10.10. I had to use special guide to install because Canon used libcupsys2 in its packages and ubuntu expects libscupsys i followed this guide in reference to this advice. The first problem was this one (the ubuntu "add printer dialog asked for root credentials". The suggested workarout in Launchpad to create a root password worked. Now i added the printer. It's available for printing. Then i got an error message "cups insecure filter" which prevented me from printing. That could be solved by setting the need root rights in the /usr/lib/cups/filter/ directory. The error message disappeared after restarting cups service. Now it should work but it doesn't. The main problem is now, the printer seems to be proper setup but when i try to print a document, the printer icon appears for short time in gnomepanel. There's a printing job in Queue which got completed, but the printer doesn't print. I attached the Debuglog provided by printer error control, had to upload to another site, since it was to big in the question body here. Perhaps someone can identify the problem with it? Note: i know that it once worked fine with an older release of Ubuntu, but not sure which version this was.

  Read the article

• Error 1603 when installing Microsoft Intellipoint 8.2 on Windows 7 x64

  - by HeB

  Installing MS Intellipoint 8.2 (for my MS touch mouse) on my Dell Inspiron 580 always gives the following error: "Setup must close because an error occurred. Verify that your computer meets the system requirements on the product packaging. Restart your computer and try running Setup again. If this error happens again, see Help for customer support options. (Error Code 1603)" I'm running Windows 7 x64 with all latest updates. MS solutions don't work. How to fix?

  Read the article

• Running a home mail server using dynamic dns

  - by user4009

  Hi, Is it possible to run an email server on my home box using dynamic dns? The scenario is, I want to auto cc all incoming and outgoing emails from my one account to another, from some server side config instead of configuring email clients for rules. I have tried Google Apps Mail but it doesn't allow auto cc of outgoing emails. After having read tons of blogs, forum messages etc (hope I have been reading the correct info :) ) the only option to achieve what I am needing is to setup my own mail server, but the cost of getting a static IP doesn't fit my budget. Please can someone point me in the correct direction. Platform doesn't matter, I can setup a Windows or Linux server. Many Thanks

  Read the article

< Previous Page | 197 198 199 200 201 202 203 204 205 206 207 208  | Next Page >