Search Results

Search found 6942 results on 278 pages for 'enabled'.

Page 202/278 | < Previous Page | 198 199 200 201 202 203 204 205 206 207 208 209  | Next Page >

  • HP DL185 - very slow disk read speed

    - by fistameeny
    Hi, I have a HP DL185 G6 Server (12 disk model) with the following spec: Quad Core Xeon 2.27GHz 6GB RAM HP P212 RAID controller with battery backup 2 x 128GB 15K SAS 3.5" (RAID-1 for the operating system) 4 x 750GB 7.5K SAS 3.5" (RAID-5 for the data, 2TB usable space) The operating system is Ubuntu Server 9.10. Both drives have been formatted as EXT4. We are finding that read speed of the RAID-5 array is poor. Disk test results below: sudo hdparm -tT /dev/cciss/c0d1p1 /dev/cciss/c0d1p1: Timing cached reads: 15284 MB in 2.00 seconds = 7650.18 MB/sec Timing buffered disk reads: 74 MB in 3.02 seconds = 24.53 MB/sec For info, the RAID-1 array performs as follows: sudo hdparm -tT /dev/cciss/c0d0p1 /dev/cciss/c0d0p1: Timing cached reads: 15652 MB in 2.00 seconds = 7834.26 MB/sec Timing buffered disk reads: 492 MB in 3.01 seconds = 163.46 MB/sec We thought this was because with no battery, read/write cache is disabled. We have bought and installed the battery backup and have used the HP bootable CD to change the cache settings to 50% read / 50% write and check cache is enabled on the drives and the controller. Is there something I'm missing?

    Read the article

  • Diagnosing "The specified module could not be found" on IIS7 with ASP.Net

    - by Baldy
    I am migrating some web apps from a windows 2003 server with IIS6 server to a Windows server 2008 R2 server with IIS7. One of the apps, which runs on asp.net v2.0 using forms authentication will not load. It gives me the following error... The specified module could not be found. (Exception from HRESULT: 0x8007007E) Description: An unhandled exception occurred during the execution of the current web request. Please review the stack trace for more information about the error and where it originated in the code. Exception Details: System.IO.FileNotFoundException: The specified module could not be found. (Exception from HRESULT: 0x8007007E) Now i fully understand that the app cannot load some kind of resource due to a FileNotFoundException, but i am struggling to diagnose exactly where in the application this is happening, as it does not tell me what the module is, nor what file it is looking for. I have enabled failed request tracing and i get back a complete request trace, yet i cannot find anything that gives me detail on this specific error, or the module involved. Any advice on diagnosing the root cause of the issue would be greatly appreciated.

    Read the article

  • AGP 4x slot running at 2x

    - by Wesley
    Hi all, Here are the specs of the machine related to this question: AMD Athlon XP 2400+ @ 2 GHz / 2x 512MB PC3200 DDR RAM / 3D Fuzion 128MB GeForce 6200 AGP / WD 160GB IDE HDD / FIC AM37 (mobo) / Codegen 350W PSU / Windows XP Pro SP3 So, for some odd reason, the GeForce 6200 that is in the AGP 4x slot is not running at 4x, but 2x. The card itself supports AGP 4x and even 8x. When I enter the BIOS, the options for the AGP slot only allow 2x as the max. Before, the max option for the AGP slot in the BIOS was 4x. (I do get the 4x option after I reset CMOS, but it does not stick after a restart.) I don't exactly know what the problem could be, but a few weeks ago, this machine's hard drive was reformatted and got a fresh install of XP. Also, I did install Rivatuner, but I never overclocked it at all. (I uninstalled it after thinking that it had done something.) Otherwise, I cannot figure out the cause of the problem. Does anybody have an idea why this is happening? (Would I have to do another reformat?) Thanks in advance. PS: the other options for the AGP slot are aperture size (which I tried changing, but it did nothing) and FastWrite (enabled by default).

    Read the article

  • Routing table on Linux not respected

    - by MRHaarmann
    I have a very specific problem, building a Linux VPN endpoint (with external VPN Gateway), which should route certain networks over the tunnel, others via default gateway. The Linux VPN should do a NAT on the outgoing connections for the VPN peers. Setup is as following: Internet gateway LAN 192.168.25.1/24 VPN Gateway LAN 10.45.99.2/24 (VPN tunnel 10.45.99.1 to net 87.115.17.40/29, separate connection to Internet) Linux VPN Router eth0 192.168.25.71/24 eth0:503 10.45.99.1/24 Default 192.168.25.1 route to 87.115.17.40/29 via 10.45.99.2 (send_redirects disabled, ip_forward enabled) Linux clients (multiple): eth0 192.168.25.x/24 Default 192.168.25.1 route to 87.115.17.40/29 via 192.168.25.71 Ping to the machines via tunnel from the VPN Router is working. Now I want to establish a routing from my clients over the VPN gateway and the client packet gets routed to 192.168.25.1 ! traceroute output shows the packets get routed to 192.168.25.71, but then to 192.168.25.1. So the route is not respected in forward ! IPTables and Routing: ip route show 87.115.17.40/29 via 10.45.99.2 dev eth0 10.45.99.0/24 dev eth0 proto kernel scope link src 10.45.99.1 192.168.25.0/24 dev eth0 proto kernel scope link src 192.168.25.71 default via 192.168.25.1 dev eth0 iptables -A INPUT -i eth0:503 -j REJECT iptables -t nat -A POSTROUTING -o eth0:503 -j MASQUERADE iptables -A FORWARD -i eth0:503 -m state --state RELATED,ESTABLISHED -j ACCEPT iptables -A FORWARD -s 192.168.25.0/24 -o eth0:503 -j ACCEPT So what is wrong with my setup ? The route is chosen correctly from localhost, but all the clients get forwarded to the Internet GW. thanks for helping, Marcus

    Read the article

  • Slow Local Network, Windows 7, Snow Leopard, WiFi/Wired

    - by WerkkreW
    I am experiencing really poor local network performance in my home. I was recently using a Linksys WRT54G Router with DD-WRT on it, and a couple comparable Linksys-G PCI cards for connectivity but decided to upgrade hoping it would help with my performance issues. The computers in my house are connected as follows: Comcast Business Class Commercial 25mbps/10mbps (Verified) D-Link DGL-4500 Wireless N Router Windows 7x64 - D-Link DWA-552 Wireless-N Windows 7x64 - D-Link DWA-552 Wireless-N Mac Mini 10.6.2 - AirPort Extreme N Playstation 3, Hard Wired Xbox 360, Hard Wired Essentially the problem is very specific. Web browsing and uploading/downloading files from the internet is fine, more than fine. But if I want to say, Stream a video from one of my Windows 7 computers to my PS3, or copy a large video file between either of the PC's or the Mac, I get a consistent 500-900Kbps throughput at the high end. If I open my network browser, or try to browse my homegroup the response time is horrible. Both of my Windows computers are showing Strong wireless signals with a connection speed of 300Mbps. I know I can never expect to achieve anything near those speeds, but 500Kbps? Here is what I have tried so far: Enabled Single mode N-only and N/G Only on router WPA2 with AES Encrpytion Disabled "Remote Differential Compression" in Windows 7 Disabled TCP "Auto-Tuning" Used other software for file copies such as "Teracopy" I am at the end of my rope. Unfortunately I live in a 75 year old home with plaster walls, so hard-wiring my entire house isn't really an option I can handle right now. Any ideas to help me get decent speed when transferring files across my network would be greatly appreciated.

    Read the article

  • Unable to logon using terminal server connection

    - by satch
    I have several W2K3 SP2 servers, admin TS enabled. I discovered this morning, I was unable to logon into some of them. I've a couple of Citrix servers in different farms, a SAP (IA64) app server and a cvs server. All of them show same sympthoms; remote connections are refused. I've been able to logon locally, and terminal server service is up, there are no users (so connections are not depleted). There are no errors in log in most servers. One of the Citrix ones, reported following errors: Event ID 50 Source TermDD Type Error Description The RDP protocol component X.224 detected an error in the protocol stream and has disconnected the client. and Event ID 1006 Source TermService Type Error Description The terminal server received large number of incomplete connections. The system may be under attack. Anyway, I suppose these errors appear because server isn't working, and Citrix users try to logon massively. (I nmap'ed server and port seems up). I've solved this problem rebooting before, but with so many servers affected it seems like a crappy workaround. Any idea about troubleshooting it properly? Thanks in advance

    Read the article

  • How to fix IE starting when I try to start Opera?

    - by Scott Leis
    I have a problem that started today, where trying to run any of the 3 versions of Opera I have installed causes Internet Explorer to start instead. The Opera versions I have installed are 9.64, 10.10, and 10.63. My OS is Windows Vista with the latest critical/important updates. The behaviour is the same regardless of whether I double-click a shortcut to Opera, double-click on Opera.exe in one of the install directories, or run Opera.exe with the full path from Start-Run. The only work-around I've found is to right-click Opera.exe or a shortcut, and click "Run as administrator". This starts Opera, and it appears to work normally. Opera seems to be the only program so affected. I've checked Firefox and a few other (non-browser) programs, and they work normally. When IE starts instead of Opera, there are always two instances of iexplore.exe started, and they both crash before I can do anything else. IE also crashes if I try to start it from its own shortcut, but I don't know if that only started today, since I hadn't used IE for a few weeks. Does anyone know what might cause this and how to fix it? It's possible my PC has a virus, but BitDefender (for which I have automatic updates enabled) hasn't detected anything.

    Read the article

  • What are these CPU cache settings? Snoop Filter, ACL prefetch, HW prefetch

    - by eater
    I was in my BIOS setup turning on VT-x support today and saw these other settings. A little googling indicates that they each seem to turn on some sort of optimization to do with the CPU's L2 cache. They were all turned off by default. The processor in question is an Intel Xeon quad-core 3.4GHz (X5492). My OS is Linux 2.6.35.10-74.fc14.x86_64 #1 SMP Thu Dec 23 16:04:50 UTC 2010 x86_64 x86_64 x86_64 GNU/Linux. I have 4GB of RAM if that matters. Here's what the BIOS manufacturer has to say: Snoop Filter Enabling the snoop filter typically improves performance by reducing snoop traffic on the frontside bus in dual processor configurations. Well I like the sound of improved performance. Why would the BIOS have this off by default? Or by dual processor do they not mean multi-core? Regardless, is there a downside if this is on? ACL Prefetch When enabled, the Adjacent Cache Line Prefetcher fetches both cache lines that comprise a cache line pair when it determines required data is not currently in its cache. When disabled, the processor will only fetch the cache line required by the processor. HW Prefetch Fetches an extra line of data into L2 from external memory. Both of these sound like optimizations that have some drawbacks. What are the reasons to turn them on? What are the reasons to leave them off. Why is the default off?

    Read the article

  • How to set up daisy-chained routers for separate sub-nets?

    - by joe
    This question seems to be similar to others, but I'll take a shot anyway. A client recently switched ISPs from TDS to Comcast Business Class. Before the switch, they had 5 static IP addresses assigned. Now they'll have a single IP address that will change whenever Comcast decides to do so. The issue is that this internet connection will be shared among two companies, both having (and wanting to keep) their own private subnets. Because TDS was supplying multiple IP addresses to the one location, this allowed me to put each router on the switch. Now, with Comcast, they only get one IP address, meaning there has to be a main router before the subnet routers. Luckily, the cable modem has a built-in router, which I would like to connect to each company's router, and still have DHCP enabled on all accounts. Question: What do I need to do to the subnet routers to keep them separate from each other, but still allow internet access from the main router. I would love to say "I tried this", and give you links, but everything I find on the internet only mentions daisy-chaining routers with DCHP disabled.

    Read the article

  • DPMS does not work: the monitor is not switched off

    - by bortzmeyer
    I have a monitor which was properly switched off by my Debian PC when unused. I attached it to another machine and, this times, it is never switched off. In /etc/X11/xorg.conf, I have: Section "Monitor" Identifier "Generic Monitor" Option "DPMS" It is recognized when X11 starts: (II) Loading extension DPMS ... (II) VESA(0): DPMS capabilities: StandBy Suspend Off; RGB/Color Display ... (**) Option "dpms" (**) VESA(0): DPMS enabled The operating system is Debian stable "lenny". The graphics card is: 00:02.0 VGA compatible controller: Intel Corporation 82G33/G31 Express Integrate d Graphics Controller (rev 02) (prog-if 00 [VGA controller]) Subsystem: Hewlett-Packard Company Device 2a6f Flags: bus master, fast devsel, latency 0, IRQ 5 Memory at fe900000 (32-bit, non-prefetchable) [size=512K] I/O ports at b080 [size=8] Memory at d0000000 (32-bit, prefetchable) [size=256M] Memory at fe800000 (32-bit, non-prefetchable) [size=1M] Capabilities: [90] Message Signalled Interrupts: Mask- 64bit- Queue=0/0 Enable-Capabilities: [d0] Power Management version 2 X11 is: X.Org X Server 1.4.2 Release Date: 11 June 2008 X Protocol Version 11, Revision 0 Build Operating System: Linux Debian (xorg-server 2:1.4.2-10.lenny2) Current Operating System: Linux ludwigVII 2.6.26-2-686 #1 SMP Sun Jun 21 04:57:3 8 UTC 2009 i686 Build Date: 08 June 2009 09:12:57AM

    Read the article

  • Anonymous file sharing without login window, from Windows 7 server to XP clients

    - by Niten
    I'm trying to provide machines on a small LAN with read-only, anonymous access to files shared from a Windows 7 workstation (let's call it WIN7SVR). In particular, I don't want clients to have to deal with a login window when they navigate to, e.g., \\WIN7SVR in Windows Explorer, but we do not have a domain and synchronizing accounts between the server and clients would be intractable. There are both Windows 7 and Windows XP clients that need access to these shares. I got this working for Windows 7 clients by just enabling the Guest account on WIN7SVR and setting appropriate share permissions. Other Windows 7 machines automatically try logging in as Guest, it seems, so their users don't have to deal with the login window. The problem is with the XP clients--they can access the server if the user enters "Guest" in the login window, but I don't want users to have to do that. So from what I gather, in my limited understanding of Windows file sharing, this boils down to granting null sessions access to file shares on WIN7SVR. But I've had no success so far on that front. I've tried all the following in the local group policy editor on the Windows 7 server: Set Network access: Let Everyone permissions apply to anonymous users to Enabled Set Network access: Restrict anonymous access to Named Pipes and Shares to Disabled Added the names of corresponding shares to Network access: Shares that can be accessed anonymously Added "ANONYMOUS LOGON" to Access this computer from the network under User Rights Assignment Any advice would be highly appreciated... I'm mostly a Unix guy, so I feel somewhat out of my league with Windows file sharing. I do understand that any sort of anonymous access to file shares isn't generally ideal from a security standpoint, but it's the most practical solution for us in this case, and access to our network is well enough controlled that share-level security isn't a concern.

    Read the article

  • Flickering dual screens in Virtual Box Ubuntu 13.10 Guest

    - by alexleonard
    I have Ubuntu 13.10 x64 installed as a guest in VirtualBox (under a Windows 8.1 host) and have the settings for the virtual machine setup to run with a monitor count of 2, 128MB video memory and 3D acceleration enabled. In my guest I have the virtual box additions installed (which allowed me to have two 1920x1080 screens). Here's a screenshot of my VM settings. My laptop is an Asus N550JV which has both Intel's HD Graphics 4600 GPU and Nvidia's GeForce GT 750M. By default though I believe the Intel GFX card is being used to render the VM. When I boot up the VM it loads perfectly on dual screens, however whenever I move the mouse from one screen to the other (I have a Dell S2340L running over a HDMI connection as a second screen) the screen flickers. I've tried a variety of settings changes in both Ubuntu and the VM settings, but cannot seem to stop this screen flicker. I also used the NVidia control panel in Windows to force the dedicated graphics card to always be used but found that the display driver sometimes crashed whilst working in the VM, resulting in my VM session being destroyed, so I figured it's better to stick with the Intel GFX as that appears to be more stable. I also tried without 3D acceleration but that was much worse, and if I ran the VM with a low amount of graphics memory it really struggled. Here's my dmesg output: http://pastebin.com/1LJuYWMj (not sure if this is helpful in this situation). I read some posts suggesting changes to /etc/X11/xorg.conf but I don't appear to have an xorg.conf file. There were also a few posts (though related to Synergy) suggesting running xset -dpms but this command doesn't appear to have had any effect for me. As an additional note, I'm finding that window drawing in the guest is a little laggy/glitchy. For example, quickly scrolling through a web page may result in parts of the viewport displaying original content. Certainly I notice drawing issues most in the web browser, but it also impacts other software with parts of the window not being drawn when, say, switching between accounts in thunderbird. Any suggestions greatly appreciated!

    Read the article

  • Hard Disk Not Counting Reallocated Sectors

    - by MetaNova
    I have a drive that is reporting that the current pending sectors is "45". I have used badblocks to identify the sectors and I have been trying to write zeros to them with dd. From what I understand, when I attempt writing data directly to the bad sectors, it should trigger a reallocation, reducing current pending sectors by one and increasing the reallocated sector count. However, on this disk both Reallocated_Sector_Ct and Reallocated_Event_Count raw values are 0, and dd fails with I/O errors when I attempt to write zeros to the bad sectors. dd works fine, however, when I write to a good sector. # dd if=/dev/zero of=/dev/sdb bs=512 count=1 seek=217152 dd: error writing ‘/dev/sdb’: Input/output error Does this mean that my drive, in some way, has no spare sectors to be used for reallocation? Is my drive just in general a terrible person? (The drive isn't actually mine, I'm helping a friend out. They might have just gotten a cheap drive or something.) In case it is relevant, here is the output of smartctl -i : Model Family: Western Digital Caviar Green (AF) Device Model: WDC WD15EARS-00Z5B1 Serial Number: WD-WMAVU3027748 LU WWN Device Id: 5 0014ee 25998d213 Firmware Version: 80.00A80 User Capacity: 1,500,301,910,016 bytes [1.50 TB] Sector Size: 512 bytes logical/physical Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS (minor revision not indicated) SATA Version is: SATA 2.6, 3.0 Gb/s Local Time is: Fri Oct 18 17:47:29 2013 CDT SMART support is: Available - device has SMART capability. SMART support is: Enabled UPDATE: I have run shred on the disk, which has caused Current_Pending_Sector to go to zero. However, Reallocated_Sector_Ct and Reallocated_Event_Count are still zero, and dd is now able to write data to the sectors it was previously unable to. This leads me with several other questions: Why aren't the reallocations being recored by the disk? I'm assuming the reallocation took place as I can now write data directly to the sector and couldn't before. Why did shred cause reallocation and not dd? Does the fact that shred writes random data instead of just zeros make a difference?

    Read the article

  • Connect by Wifi to Sql Server from another computer

    - by Bronzato
    I try to connect by Wifi to Sql Server with Sql Server Management Studio from another computer but it failed. I have a computer with Windows Seven & Sql Server 2008 (lets say the server computer). Next to it, I have a fresh installed computer with Windows Seven & Sql Server Management Studio (let's say the client computer). What I do on the server computer: configure firewall by enabling port 1433 enabled network protocols (TCP/IP) inside Sql Server Configuration Manager checked "Allow remote connections to this server" on server properties in Sql Server Management. started Sql Server Browser restarted services (Sql Server Browser is stopped but I think it is not neccessary, isn't it?) Next, I successfully tested a ping on the port 1433 from my client computer with a tool named tcping (ex: tcping 192.168.1.4 1433). But I still cannot connect from my client computer to Sql Server on my other computer. Ok, something new on this problem: until now, I successfully connected to my "server computer" with Management Studio. What I do is typing the computer name in the server name field in the connection window of Management Studio. My previous (failed) attempt was to type the computer name followed by the instance of sql server (ex: COMPUTER_NAME\SQL2008). I don't know why I only have to type the computer name... Nevermind. Now my new challenge is to succeed connecting my VB6 application to this remote database located on my "computer server". I have a connection string for this but it failed to connect. Here is my connection string: "Provider=SQLOLEDB.1;Password=mypassword;User ID=sa;Initial Catalog=TPB;Data Source=THIERRY-HP\SQL2008" Any idea what's wrong? Thanks

    Read the article

  • Windows recovery partition with GRUB2

    - by Actorclavilis
    So I recently got a new Toshiba laptop and installed Ubuntu 12.04 on it. Since it is a "Windows 7 Enabled" machine or some other proprietary nonsense like that, a few hardware features are designed only to work with W7. Eventually I found a way to enable these hardware functions by booting into the W7 recovery disc; however, they sporadically stop working. I'm moderately surprised that I was able to get anything to work at all, so I don't especially want to spend more time fixing the problems in a different fashion. Now I don't actually own the recovery disc; it's my father's. Since it's a pain to have to go asking for the disc every time the features stop working, I made an image of the disc and was hoping to make a 'recovery' partition like some computers have. However, unetbootin and GRUB2 both want a kernel and initrd to point to on startup, and something like set root=(hd0,1) loopback lo /w7r.iso set root=(lo) chainloader +1 in the spirit of the makeactive/ chainloader +1 commands that I used to use to dual-boot Linux and Windows simply gives me a file-not-found error. My question, therefore, is: Is it possible to, having written a Windows iso to a partition (such as with dd if=w7r.iso of=/dev/sda4) to a partition, convince GRUB2 to boot from it? Thanks in advance.

    Read the article

  • Wake-on-lan only works so many times

    - by Chance
    I have Wake-on-lan configured on my Windows XP machine so that the computer will wake up from Standby. Waking the computer from Standby via network traffic seems to work a certain number of times, say 4 or 5, then it stops working. If I restart the computer it seems to reset this behavior so that I can use WOL a few more times before it starts working. I use the command "wol" on my other, Linux machine with the appropriate IP address and MAC address of the card. I looked at the network card to see if it had different lights when WOL worked and when it didn't. When it has a solid amber light where the ethernet cable connects, WOL seems to work. When it has a flashing amber light, WOL does not. It seems that the system seems to almost "shut off" the card when it falls to sleep, but I don't know if this is a function of time or number of standby/wakeups. I have a 3Com 3c920 network card. If I look at the properties in Device Manager, I have "Allow this Device to bring the Computer out of Standby" checked. In the Advanced tab I have anything related to RWU (Remote Wake Up) enabled. I also believe I have the appropriate settings in BIOS related to Remote Wake-Up and I have tried both S1 and S3 power configurations in the BIOS. Intuitively, I would think I would uncheck "Allow the Computer to turn off this device to save power", but doing so disables the "Allow this Device to bring the Computer out of Standby" option. Does anyone know what is happening here or if there is a way to fix it? I have an integrated network card; would getting one that goes into a slot be better? I am running Windows XP on a Dell Optiplex GX240 with a 3Com 3c920 network card.

    Read the article

  • XP/Intel wirelss only showing 'hpsetup' ad-hoc network that isn't there

    - by ewall
    Trying to help my friend with her work XP laptop, which recently stopped seeing any wireless SSIDs except the SSID 'hpsetup' (presumably from a wireless-enabled HP printer). Relevant information: The laptop is a Lenovo T500 (Centrino 2 chipset) with XP SP3. The network adapter is Intel WiFi Link 5300 AGN (built-in). The latest version (13.5) of the Intel drivers only are installed, not the Intel config software, so XP is using the Wireless Zero-Config manager. The wireless router is a NetGear WGR614 v7 with 802.11b/g. The SSID is broadcasting, and all the other laptops in the house can see and connect to it. On the laptop, I have tried repairing the network connection, disabling power management, turning off 802.11a & n radio, and more... but it didn't help. Some of the wireless settings are managed by Group Policy from her office (I get the "At least one of your changes was not applied successfully to your wireless configuration" message). It is enforced to connect to "Access point (infrastructure) networks only". The real kicker is that my laptop does not an SSID named 'hpsetup' here, but it can see several broadcasted SSIDs including the one we want, while my friend's laptop doesn't see any SSID except 'hpsetup'. Any suggestions?

    Read the article

  • Roaming Profiles & Redirected Folders - storage consumption? offline files and caching?

    - by Ben Swinburne
    I understand the concepts of both roaming profiles and folder redirection and have used both separately before. I am about to set up a network from scratch and would ideally like to use both for the following reasons primarily Roaming profiles allow users to log on to any machine and have their profile Redirected profiles allow users to have their My Documents and Desktop etc backed up without the need to log off at the end of the day. The servers can run their backups overnight and there are no missing files due to the user not logging off. Redirected profiles largely alleviate the slow log in times caused by large profiles. My question is if some of the folders are redirected and therefore not part of the roaming profile what happens on machines which truly roam (i.e. laptops)? If there's offline files or a cache does this mean that the problem whereby a user has to log off comes back? By having them both enabled, is there any duplication i.e. if I have a users$ share and a profiles$ share would I have Desktop twice for example?

    Read the article

  • TOR Proxy / Vidalia "New Identity" button not working

    - by Yisman
    I need to hide my ip from time to time. In Vidalia, I click on "New Identity". Ihen I check http://myip.ozymo.com/ to see if my IP address has changed. But, no, it hasn't. Why is that? And how can this be fixed? I tried waiting till the button gets re-enabled to make sure that its done processing the command, but still the IP address is the same. In Fiddler each request is tracked, so it's not a cached response. It's re-requested, but simply does not change. Fiddler though does show one thing interesting. Here is the raw response of many of the requests: HTTP/1.1 200 OK Content-Length: 13 Date: Mon, 23 May 2011 12:02:57 GMT Server: Apache X-Powered-By: PHP/5.2.14 Content-Type: text/html; charset=UTF-8 Age: 1 Connection: keep-alive **Warning: 110 localhost:8118 Object is stale** 26.32.120.106 What is this warning? And is this the cause?

    Read the article

  • Wake on LAN Problem

    - by Caley Woods
    I'm working to get wake on lan (wol) working so that we can do some power management at my workplace. I've enabled WOL on a test laptop running Win 7 x64 and put it to sleep and hibernate both with no luck. I'm using a 3rd party utility and I've ran wireshark on the test laptop with it booted up and I can see the WOL packets coming in and the machine refuses to wake from sleep or hibernate. I thought maybe it was the computer I was using so I had another Win 7 x64 laptop nearby and I tried it, same scenario. We're in a cisco environment and I believe I gotten all the pieces in place since I'm seeing the WOL packets come through. I've tested two machines on the same subnet to eliminate the possibility of a misconfiguration on the switch, this also has the same behavior. The laptop models are a Compaq 6510b and 6730b. Is there something I'm missing? I'm trying this across UDP port 50200 since that's the port the actual management system will use after I get it working.

    Read the article

  • Keepalived for more than 20 virtual addresses

    - by cvaldemar
    I have set up keepalived on two Debian machines for high availability, but I've run into the maximum number of virtual IP's I can assign to my vrrp_instance. How would I go about configuring and failing over 20+ virtual IP's? This is the, very simple, setup: LB01: 10.200.85.1 LB02: 10.200.85.2 Virtual IPs: 10.200.85.100 - 10.200.85.200 Each machine is also running Apache (later Nginx) binding on the virtual IPs for SSL client certificate termination and proxying to backend webservers. The reason I need so many VIP's is the inability to use VirtualHost on HTTPS. This is my keepalived.conf: vrrp_script chk_apache2 { script "killall -0 apache2" interval 2 weight 2 } vrrp_instance VI_1 { interface eth0 state MASTER virtual_router_id 51 priority 101 virtual_ipaddress { 10.200.85.100 . . all the way to . 10.200.85.200 } An identical configuration is on the BACKUP machine, and it's working fine, but only up to the 20th IP. I have found a HOWTO discussing this problem. Basically, they suggest having just one VIP and routing all traffic "via" this one IP, and "all will be well". Is this a good approach? I'm running pfSense firewalls in front of the machines. Quote from the above link: ip route add $VNET/N via $VIP or route add $VNET netmask w.x.y.z gw $VIP Thanks in advance. EDIT: @David Schwartz said it would make sense to add a route, so I tried adding a static route to the pfSense firewall, but that didn't work as I expected it would. pfSense route: Interface: LAN Destination network: 10.200.85.200/32 (virtual IP) Gateway: 10.200.85.100 (floating virtual IP) Description: Route to VIP .100 I also made sure I had packet forwarding enabled on my hosts: $ cat /etc/sysctl.conf net.ipv4.ip_forward=1 net.ipv4.ip_nonlocal_bind=1 Am I doing this wrong? I also removed all VIPs from the keepalived.conf so it only fails over 10.200.85.100.

    Read the article

  • Guide To Setting Accessing PhpMyAdmin On NGINX, Ubuntu 11.04, EC2 Remote MySQL Instance

    - by darkAsPitch
    I have setup a domain name to run on amazon ec2 running ubuntu 11.04, nginx and php5-fpm. The domain name works great, I have setup it's own sites-available configuration file and sym-linked it to sites-enabled. I installed phpmyadmin via sudo apt-get install phpmyadmin and followed the instructions. I then added this just above my /etc/nginx/nginx.conf file and restarted nginx. server { listen 80; server_name phpmyadmin.domain.com; location / { root /usr/share/phpmyadmin; index index.php; } #make sure all php files are processed by fast_cgi location ~ \.php { # try_files $uri =404; fastcgi_index index.php; fastcgi_pass 127.0.0.1:9000; include fastcgi_params; fastcgi_split_path_info ^(.+\.php)(/.+)$; fastcgi_param PATH_INFO $fastcgi_path_info; fastcgi_param PATH_TRANSLATED $document_root$fastcgi_path_info; fastcgi_param SCRIPT_FILENAME $document_root$fastcgi_script_name; } } I have also added the appropriate dns A records for phpmyadmin.domain.com phpmyadmin.domain.com just shows a 404 error code. All other subdomains do not respond at all so at least something is working here. FYI I have edited the /etc/phpmyadmin/config.inc.php file so that I can connect to a remote MySQL Database. What else do I need to do?

    Read the article

  • Internet Explorer / Windows 7 does not want to show HTML file from local network drive

    - by Jaanus
    Setup: I have Windows 7 running inside VirtualBox on Mac OS X host. I have a shared drive with some HTML files, that I am mounting as a local drive W: in Windows, from the VirtualBox server \VBOXSVR. I want to look at them with a browser in Windows. Chrome in Windows 7 opens and shows those HTML files just fine (file:///W:/welcome.html). But Internet Explorer does not, and shows this error instead of the files: Internet Explorer cannot display the web page What you can try: [button Diagnose Connection Problems] More information This problem can be caused by a variety of issues, including: Internet connectivity has been lost. The website is temporarily unavailable. The Domain Name Server (DNS) is not reachable. The Domain Name Server (DNS) does not have a listing for the website's domain. If this is an HTTPS (secure) address, click Tools, click Internet Options, click Advanced, and check to be sure the SSL and TLS protocols are enabled under the security section. For the internet zone in the status bar, it shows: Internet | Protected Mode: On IE settings are a mystery to me, and I could possibly get it to work by tweaking IE settings, but I don't know which ones. How do I make IE show the same files that Chrome is happy to show? (Chrome showing them means that the files themselves are fine, there is something about the setup that just makes IE be a diva.)

    Read the article

  • Getting access to physical drives in ESXi v5.5 installation on Dell PowerEdge R710 with PERC 6/i

    - by Big-Blue
    I've acquired a Dell PowerEdge R710 server a few days ago, which includes a PERC 6/i RAID controller. The server is now fitted with a SATA SSD, one SAS drive and four SATA HDD's, all of which I would like to be passed through to ESXi in an "as-is" state, without creating any logical drives in the RAID controller. Now, the ESXi v5.5 installation image I grabbed from the Dell homepage starts just fine but only lists the logical drives and connected flash drives as possible installation targets, not any of the physical drives. If I create a small logical drive on my SSD (which the PERC 6/i detects as SATA-SSD type), the ESXi install wizard lists the SSD value on that drive as false; which is far from optimal. I have also tried disabling the RAID controller entirely in the setup, but that also did not help. Everything that should enable passthrough is enabled in BIOS, but that shouldn't be a concern at this early stage of the ESXi installation. How would I be able to install ESXi v5.5 to a part of my SSD that is connected to the storage controller, while giving it entire physical access to the disk (to allow for SMART values to be read etc.)?

    Read the article

  • Permission Denied for FTP User

    - by Alasdair
    I have an FTP user whose default is /root/ftpuser This user can login fine. The user is the owner of the directory & the directory is even set to 777 permissions. But the user can't upload anything, the display is: Status: Connecting to xx.xxx.xxx.xx:21... Status: Connection established, waiting for welcome message... Response: 220---------- Welcome to Pure-FTPd [privsep] [TLS] ---------- Response: 220-You are user number 2 of 50 allowed. Response: 220-Local time is now 05:12. Server port: 21. Response: 220-This is a private system - No anonymous login Response: 220-IPv6 connections are also welcome on this server. Response: 220 You will be disconnected after 15 minutes of inactivity. Command: USER ftpuser Response: 331 User ftpuser OK. Password required Command: PASS ********* Response: 230 OK. Current restricted directory is / Command: OPTS UTF8 ON Response: 200 OK, UTF-8 enabled Status: Connected Status: Starting upload of test.html Command: CWD / Response: 550 Can't change directory to /: Permission denied Command: MKD / Response: 550 Can't create directory: Permission denied Command: CWD / Response: 550 Can't change directory to /: Permission denied Command: SIZE /btn.png Response: 550 Can't check for file existence Command: TYPE I Response: 200 TYPE is now 8-bit binary Command: PASV Response: 227 Entering Passive Mode (66,232,106,33,52,218) Command: STOR /test.html Response: 553 Can't open that file: Permission denied Error: Critical file transfer error It's a Linux CentOS 6 server. Any ideas?

    Read the article

< Previous Page | 198 199 200 201 202 203 204 205 206 207 208 209  | Next Page >