Search Results

Search found 6942 results on 278 pages for 'enabled'.

Page 201/278 | < Previous Page | 197 198 199 200 201 202 203 204 205 206 207 208  | Next Page >

• GA 8KNXP Rev1.0: 4GB installed, only 3.5 recognized by BIOS

  - by hurikhan77

  I've installed 2x 1 GB and 4x 512 MB memory into my GA-8KNXP system which would sum up to 4GB. The specs from the manual say: Maximum memory support: 4GB. If all six slots are utilized, slot 5+6 may only equipped with single-sided RAM modules. And so I did. Anyway: The BIOS counts up to 3.5 GB and finishes there. Also my linux system reports only 3.5 GB of memory although 4 GB memory support is activated in the kernel. So I suppose this is a memory mapping issue or a hardware issue. I've tried removing only on of the 512 MB memory modules leaving 5 modules in place. But that just stopped the system from powering on correctly (screen stays black although fans and leds come to live). Dual Channel was detected and enabled so the system technically found all 6 modules. "dmidecode" in linux reports only memory in slots 1 to 4 and ignores slots 5+6, so it only detects 3 GB of memory. It also says the system would support up to 16 GB of memory with 4 GB modules per slot. I think technically the chipset should be able to offer and utilize the complete 4 GB memory range. Any clues what else I could check? Or do I have just to live with 0.5 GB wasted memory?

  Read the article

• IIS 6 Windows Authentication in ASP.Net app fails

  - by Kjensen

  I am trying to install an ASP.Net app on an IIS6 webserver. The site requires the user to authenticate with windows, and this works on several other apps on the same server. In IIS I have enabled anonymous access and windows authentication. In web.config, authentication is set to: <authentication mode="Windows"/> and authorization...: <authorization> <allow roles="Users"/> <deny users="*"/> </authorization> Ie. allow all users in role "Users" and deny everybody else. This is the approach that is working with several other apps on the same server. If I run the site, I am prompted for username and password. If I remove the line: <deny users="*"/> I can access the site and everything works - but the user credentials are not passed to the site (Page.User.Identity.Name returns a blank string in ASP.Net). The site has identical (inherited) file permissions as other working sites on the server. The only difference in authentication/authorization between this site and the other working sites is, that this runs Asp.Net 4 (but there are other working asp.net 4 sites on the server as well). What am I missing here? Where should I look?

  Read the article

• Standard PHP configuration command for centos 6.5

  - by Krishna

  First of all let me tell you my knowledge in managing server and configuring script is very basic. Now I am trying to setup a server for my personal use. My server is up and running in Centos 6.5 with PHP, MySql and ISPConfig. I felt that even PHP is installed it needs some configuration for a standard web server. I searched on and found some 'configure' command but none working. The reason they did not have a specific step by step guidance on how to do this. Can somebody help me to configure PHP in a standard way? Thanks in advance. Some more detail, as required - 1. I did not install PHP from source. 2. Yes, I want some standard modules to be enabled in PHP 3. I also want to know do I need to change some settings on default? I do have a managed VPS, so do you suggest me to copy php.ini from that VPS to new dedicated server so all required settings which is working fine for me to be copied here also? Thanks

  Read the article

• Computer Freezes with "Bugcheck 0" on Windows 7. How do I figure out why?

  - by George Stocker

  After about 10 minutes of running, my computer will hang, exhibiting the following symptoms: Both monitors act as if there is no image being sent to them (on, but blacked out) The CAPS Lock key on the keyboard will not respond. The computer appears to still be running: CPU Fan is whirring. When I reboot, Windows says "The previous shutdown was unexpected." I've enabled the 'don't automatically restart' on an error, and asked the computer to make a memory dump whenever it crashes, but it hasn't done either. The problem is that there's no bugcheck for me to go off of, so there's no way for me to determine what the cause is (I think). Here are my system specs: Intel Core 2 Duo E6750 Gigabyte P35C-DS3R w/ 4.00 GB (DDR2 Ram) Nvidia 8800 GT Windows 7 I've tried running the Windows Memory checker, but the system also freezes when using that after about 10 minutes as well. How can I diagnose the problem with no bugcheck and no ability to run a memory checker? Update Running Memtest86 also causes the computer to crash (looks like it doesn't make it through a full pass - it was only running for about 10 minutes when the PC stopped responding).

  Read the article

• 2010 cgi script failure

  - by Barry F

  Hi. I hope you can help, I'm just a beginner! I have listed a few extra details which may not be relevant. I upload cgi scripts onto local/personal directory on a Apache/2.2.10 server, using FTP95Pro in ASCII. The scripts execute correctly using perl on my web-server in a terminal session. Thus my code has no fatal syntax errors. Webpages 'action' each cgi script at /cgi-bin/. There are symbolic links which link system directory files to my local directory files. FollowSymLinks is enabled (unsure how). Permissions are correct (755). This set-up hasnt changed, apparently. The scripts have excuted perfectly for years, up to 2010. But now, in 2010, I have replaced working scripts with new script/files, now with exactly the same text, filename and permissions. Only the date (last modified) has changed. But now I receive a 500 Internal Server Error, and cannot determine why. My server administator assumes I have code errors. But code is unchanged since last year, and it runs fine (albeit no arguments) on web-server console using perl myscript.cgi Is there anything you can think of which may have changed ? I'm suspicious of the new decade. I think the server swapped from Linux to Windows OS last year, but my server administrator got it all working OK. Is there something unusual he may have missed, related to 2010 ? Thank you in advance

  Read the article

• Why does Exchange 2003 silently reject emails with large attachments?

  - by Cypher

  Our environment: Exchange Server 2003 Standard, single instance, running on Windows Server 2003 Standard. configured to not send/receive mail with attachments larger than 10 MB. NDRs are not enabled. The issue: When an external sender sends an email with an attachment larger than 10MB, Exchange, as configured, does not receive the message. However, the sender of that message does not receive any notifications from his own mail server that the message could not be delivered due to attachment size. However, if an external user tries to send an email to a non-existent user, they do receive a message from their mail server indicating that the user does not exist. Why is that, and is there anything I can do about it? It would be nice if the sender received notification that the attachment file size exceeds our limits and their message was never received... Update The Exchange server has a SpamAssassin box in front of it... could that have something to do with it? Here is one of the last lines from SpamAssassin's logs when searching for my test e-mails: mail postfix/smtp[19133]: 2B80917758: to=, relay=10.0.0.8[10.0.0.8]:25, delay=4.3, delays=2.6/0/0/1.7, dsn=2.6.0, status=sent (250 2.6.0 Queued mail for delivery) My assumption is that Spam Assassin thinks the message is OK and is forwarding it off to Exchange. Update I've verified that Exchange is receiving the message and generating an NDR. However, delivery of NDRs are disabled to prevent Backscatter. Is there something that I can do to get Exchange to send a bounce message to the sending mail server (or verify that message is being sent) so the sending mail server can notify its sender of the bounce?

  Read the article

• Requests per second slower when using nginx for load balancing

  - by Ed Eliot

  I've set up nginx as a load balancer that reverse proxies requests to 2 Apache servers. I've benchmarked the setup with ab and am getting approx 35 requests per second with requests distributed between the 2 backend servers (not using ip_hash). What is confusing me is that if I query either of the backend servers directly via ab I get around 50 requests per second. I've experimented with a number of different values in ab the most common being 1000 requests with 100 concurrent connections. Any idea why traffic distributed across 2 servers would result in fewer requests per second than hitting either directly? Additional info: I've experimented with worker_processes values of between 1 and 8, worker_connections between 1024 and 8092 and have also tried keepalive 0 and 65. My main conf currently looks like this: user www-data; worker_processes 1; error_log /var/log/nginx/error.log; pid /var/run/nginx.pid; worker_rlimit_nofile 8192; events { worker_connections 2048; use epoll; } http { include /etc/nginx/mime.types; sendfile on; keepalive_timeout 0; tcp_nodelay on; gzip on; gzip_disable "MSIE [1-6]\.(?!.*SV1)"; include /etc/nginx/conf.d/*.conf; include /etc/nginx/sites-enabled/*; } I've got one virtual host (in sites available) that redirects everything under / to 2 backends across a local network.

  Read the article

• How to have a shell script available everywhere I SSH to

  - by aib

  I have a shell script which I simply cannot do without: bar from Theiling Online I use SSH a lot and on a variety of *nix servers. However, I am not a system administrator and usually don't have the time or privileges to install it on every server I connect to. It is apparently a very portable sh script and has command line options to export itself as a shell function, which got me thinking: Could I use one of OpenSSH's subjectively obscure features to export it everywhere I go? My first thought was to assign the source to an environment variable like BAR = "cat -v" and then execute it on the other side as `$BAR`, but 1) I can't even get the cat example to to work locally, 2) I don't know how to put the script's actual multiline source into an environment variable and 3) I have yet to see a machine with PermitUserEnvironment enabled. I guess I could even do with an ssh option to write a file called ~/bar at logon, but a more volatile solution would be better. Calling wget http://.../bar at logon would be unacceptable. Any ideas? P.S. Putty-specific solutions, though I doubt any would exist, are also fine.

  Read the article

• Selecting Interface for SSH Port Forwarding

  - by Eric Pruitt

  I have a server that we'll call hub-server.tld with three IP addresses 100.200.130.121, 100.200.130.122, and 100.200.130.123. I have three different machines that are behind a firewall, but I want to use SSH to port forward one machine to each IP address. For example: machine-one should listen for SSH on port 22 on 100.200.130.121, while machine-two should do the same on 100.200.130.122, and so on for different services on ports that may be the same across all of the machines. The SSH man page has -R [bind_address:]port:host:hostport listed I have gateway ports enabled, but when using -R with a specific IP address, server still listens on the port across all interfaces: machine-one: # ssh -NR 100.200.130.121:22:localhost:22 [email protected] hub-server.tld (Listens for SSH on port 2222): # netstat -tan | grep LISTEN tcp 0 0 100.200.130.121:2222 0.0.0.0:* LISTEN tcp 0 0 :::22 :::* LISTEN tcp 0 0 :::80 :::* LISTEN Is there a way to make SSH forward only connections on a specific IP address to machine-one so I can listen to port 22 on the other IP addresses at the same time, or will I have to do something with iptables? Here are all the lines in my ssh config that are not comments / defaults: Port 2222 Protocol 2 SyslogFacility AUTHPRIV PasswordAuthentication yes ChallengeResponseAuthentication no GSSAPIAuthentication no GSSAPICleanupCredentials no UsePAM yes AcceptEnv LANG LC_CTYPE LC_NUMERIC LC_TIME LC_COLLATE LC_MONETARY LC_MESSAGES AcceptEnv LC_PAPER LC_NAME LC_ADDRESS LC_TELEPHONE LC_MEASUREMENT AcceptEnv LC_IDENTIFICATION LC_ALL AllowTcpForwarding yes GatewayPorts yes X11Forwarding yes ClientAliveInterval 30 ClientAliveCountMax 1000000 UseDNS no Subsystem sftp /usr/libexec/openssh/sftp-server

  Read the article

• Google Contacts/Calendars + Address Book + iCal: built-in sync (problems) or Exchange sync?

  - by jtbandes

  (I've looked at a few other questions related to this, but I've only found old questions with people saying that they're having problems, or anticipating Snow Leopard fixing them; no recent updates.) I'm looking to sync my Google Contacts & Calendars, and Gmail, with my Mac & iPhone. The iPhone I have currently set up thus: IMAP for Mail Exchange (Google Sync) for Contacts & Calendars The Mac: Address Book: built-in sync iCal: CalDAV, configured as a Google account I haven't been syncing Gmail to Apple Mail, because I was having weird IMAP glitches every so often that just got to annoying. Will Exchange / Google Sync work for this at all? Any suggestions there? Here are the other problems I'm having. Address Book only syncs certain fields (for example, Birthdays don't sync at all). I believe this is a list of the information that's synced. Address Book's "Synchronize with Google" checkbox doesn't stay checked when I quit Address Book. I think iCal is working fine, for the most part. Any suggestions on how to improve this setup? Why doesn't Address Book / Google Contacts sync stay enabled? Could I use Exchange for it like I am on the iPhone? Will that sync all the fields, including Birthdays, etc.? Thanks in advance!

  Read the article

• Recover hard disk from Raw format

  - by user1632736

  I have been all over the web today with no results. So my drive was encrypted (truecrypt) the whole drive where windows resided. I decided to partition it to install W8 and forgot it was encrypted. So the drive got damaged and not accessible. When connected to a computer it asks for formatting. Somehow I enabled the drive through TrueCrypt on another computer and I could see and get all the files. Then I decided to decrypt the drive thinking that everything would be back to normal. After decryption my drive is not NTFS it is in RAW format. I am trying every possible way to recover, and I am desperate enough to ask lol. I tried: ddrescue (linux) (not mountable, no signature, ntfsfix no good) testdisk (linux and windows) Sees the partitions but cant do anything Many recovery applications. etc etc. I read in different places that doing a quickformat to NTFS and then doing a data recovery might help. I would definitely like a second opinion. Any suggestion would be really helpful

  Read the article

• Creating a pseudoterminal to make sudo happy

  - by larsks

  I need to automate the provisioning of a cloud instance (running Fedora 17) for which the following initial facts are true: I have ssh-key based access to a remote user (cloud) That user has password-free root access via sudo. Manual configuration is as simple as logging in and running sudo su - and having at it, but I would like to fully automate this process. The trick is that the system defaults to having the requiretty option enabled for sudo, which means that an attempt to do something like this: ssh remotehost sudo yum -y install puppet Will fail: sudo: sorry, you must have a tty to run sudo I am working around this right now by first pushing over a small Python script that will run a command on a pseudoterminal: import os import sys import errno import subprocess pid, master_fd = os.forkpty() if pid == 0: # child process: now that we're attached to a # pty, run the given command. os.execvp(sys.argv[1], sys.argv[1:]) else: while True: try: data = os.read(master_fd, 1024) except OSError, detail: if detail.errno == errno.EIO: break if not data: break sys.stdout.write(data) os.wait() Assuming that this is named pty, I can then run: ssh remotehost ./pty sudo yum -y install puppet This works fine, but I'm wondering if there are solutions already available that I haven't considered. I would normally think about expect, but it's not installed by default on this system. screen can do this in a pinch, but the best I came up with was: screen -dmS sudo somecommand ...which does work but eats the output. Are there any other tools available that will allocate a pseudoterminal for me that are going to be generally available?

  Read the article

• Configure Domino to use SMTP routing and hMailServer

  - by Sébastien Lachance

  I have been trying for a couple of days to set up a Domino 8.5 server. Basically, I want everything to be run inside a local network. Right now I can send email to other user in the Domino directory without any mail address. I am pretty new to all this stuff, so maybe the answer will be really obvious. What I need to do is be able to send a mail from somewhere else to a domino user that will be redirected to his account. On the Domino server, I also have hMailServer installed on port 25. I configured Domino to use port 26. I followed those step to get where I am now. -I have set the Fully qualified Internet host name to "preview.notes". -Smtp Listener task changed to Enabled to turn on the Listener so that the server can receive messages routed via SMTP routing -Setting up SMTP routing within the local Internet domain (http://www.h2l.com/help/help85%5Fadmin.nsf/f4b82fbb75e942a6852566ac0037f284/7f9738a49efc4f58852574d500097b01?OpenDocument) -I modified the person to use the [email protected] address. -I'm using the hMailServer (which have the local "preview.local" domain name) to send mail to [email protected]. When sending mail I got an error telling that the DNS is not set up correctly. Is using the Domino Smtp server instead of hMailServer will solve the problem? I can Telnet the Domino Smtp Server.

  Read the article

• Network access lags for Win7 when server network utilization is high

  - by Jeff Miles

  We have a Dell PE2950 file server running Windows 2008, hosting a DFS namespace of ~1.2 TB. This server has two Broadcom 1Gbps NICs teamed together. When there is high traffic going to the server across the network (greater than 200 Mbps), any Windows 7 client accessing a DFS share at the time experiences severe performance problems. For example: Computer A has an AutoCAD drawing opened directly from the DFS share. Performance is normal, not causing any issues. Computer B begins a file transfer, putting a 11GB file onto a different DFS namespace, on the same server Computer A immediately notices lag while using AutoCAD. The cursor momentarily freezes within AutoCAD every 10 seconds or so, and any browsing of the DFS share is extremely slow. Computer B completes file transfer, and performance resumes to normal for Computer A. This is only affecting Windows 7 clients, using a variety of hardware (desktop + laptop). All of our Windows XP clients see no performance impact during the file transfer. Things I have tried with no change: Had Computer A work from an entirely different RAID array from the file transfer destination Updated NIC drivers on clients and server Enabled TCP offload and receive side scaling on the server NIC (previously disabled when the issue began) Antivirus disabled during file transfer I am currently having a user test applications other than AutoCAD when the file transfer occurs, and will update the question with that result. Does anyone have any recommendations for resolution or additional troubleshooting steps?

  Read the article

• IIS / Virtual Directory authentication.

  - by Chris L

  I have an IIS(v6)/Windows 2003/.Net 3.5(app code, libraries etc.) server hosting a website at www.mywebsite.com mapped to E:\Inetpub\wwwroot\mywebsite, we also have a virtual directory (VirtDir) mapped out to E:\Inetpub\wwwroot\mywebsite\files (although in theory this could be in a different directory or a separate machine) where we store a customer's files(a bunch of .pdf & .xls). Currently to access a file you can enter into the url something like: www.mywebsite.com/VirtDir/Customer/myFile.pdf and get access to the file. The problem is the user doesn't have to log into www.mywebsite.com to get access to the file, we would prefer them to log in first. We would like the user to login via the mywebsite and if valid, let them download files from the virtual directory. The www.mywebsite.com and VirtDir are separate sites on the same farm. Allow Anon Access, and Integrated Windows Authentication both enabled. I'm more of a developer and less of a Sys Admin, but hopefully I'm in the right spot, any help would be appreciated.

  Read the article

• Apache2 Re-Routing from Domain Name to Internal IP Address

  - by Richard Grey

  The problem that I am having, is that when someone goes to my domain name example.co.uk, for some reason, apache seems to be re-routing the request to the internal IP address of the server, i.e. 192.168.0.52 My Apache2 default sites enabled file is as follows: ServerAdmin [email protected] ServerName trusteeguard.co.uk ServerAlias www.trusteeguard.co.uk DocumentRoot /var/www <Directory /> Options FollowSymLinks AllowOverride All </Directory> <Directory /var/www/> Options Indexes FollowSymLinks MultiViews AllowOverride All Order allow,deny allow from all </Directory> ScriptAlias /cgi-bin/ /usr/lib/cgi-bin/ <Directory "/usr/lib/cgi-bin"> AllowOverride All Options +ExecCGI -MultiViews +SymLinksIfOwnerMatch Order allow,deny Allow from all </Directory> ErrorLog /var/log/apache2/trusteeguard-error.log # Possible values include: debug, info, notice, warn, error, crit, # alert, emerg. LogLevel warn CustomLog /var/log/apache2/trusteeguard-access.log combined Alias /doc/ "/usr/share/doc/" <Directory "/usr/share/doc/"> Options Indexes MultiViews FollowSymLinks AllowOverride All Order deny,allow Deny from all Allow from 127.0.0.0/255.0.0.0 ::1/128 </Directory> This is an Ubuntu box if that is any help ;)

  Read the article

• linux container bridge filters ARP reply

  - by Dani Camps

  I am using kernel 3.0, and I have configured a linux container that is bridged to a tap interface in my host computer. This is the bridge configuration: :~$ brctl show bridge-1 bridge name bridge id STP enabled interfaces bridge-1 8000.9249c78a510b no ns3-mesh-tap-1 vethjUErij My problem is that this bridge is dropping ARP replies that come from the ns3-mesh-tap-1 interface. Instead, if I statically populate the ARP tables and ping directly everything works, so it has to be something related to ARP. I have read about similar problems in related posts, and I have tried with the solutions explained therein but nothing seems to work. Specifically: ~$ grep net.bridge /etc/sysctl.conf net.bridge.bridge-nf-call-arptables = 0 net.bridge.bridge-nf-call-iptables = 0 net.bridge.bridge-nf-call-ip6tables = 0 net.bridge.bridge-nf-filter-vlan-tagged = 0 net.bridge.bridge-nf-filter-pppoe-tagged = 0 arptables and ebtables are not installed. iptables FORWARD is all set to accept: Chain FORWARD (policy ACCEPT) target prot opt source destination The bridged interfaces are set to PROMISC: ~$ ifconfig ns3-mesh-tap-1 Link encap:Ethernet HWaddr 1a:c7:24:ef:36:1a ... UP BROADCAST PROMISC MULTICAST MTU:1500 Metric:1 vethjUErij Link encap:Ethernet HWaddr aa:b0:d1:3b:9a:0a .... UP BROADCAST RUNNING PROMISC MULTICAST MTU:1500 Metric:1 The macs learned by the bridge are correct (checked with brctl showmacs). Any insight on what I am doing wrong would be greatly appreciated. Best Regards Daniel

  Read the article

• Mavericks permission issues with Windows Server deduplicated shares

  - by dmohlmaster

  We have a number of 10.9-10.9.3 - Mavericks - machines installed throughout our facility. Much of the user content is pulled from shares stored on our Windows Server 2012 fileservers with deduplication enabled. I have found that files newly written or unoptimized are able to be accessed without issue - read, written, modified, etc. Once the file gets optomized/deduplicated and Windows adds the P & L attributes - sparse and symlink - the Macs running Mavericks begin to have access issues. Once the files get deduplicated, users begin receiving read access errors when copying files (see error1 below). This happens when copying to folders within the current folder tree or copying somewhere to the local system. If you 'stop' the copy operation and retry a few more times, it may eventually work for the specific instance but fail again later. I am however, able to copy these files without issue via the terminal. Other systems running 10.7 do not experience the same issues and are able to access file server resources without issue. Many of the systems having issues are newer and thus not able to be downgraded to 10.8 or 10.7. I have tried finder replacements such as Pathfinder but the results are the same. I know this is at least similar to the issues many Mac users are already experiencing and posting about but I haven't seen it directly linked to deduplication and the attributes written by Windows server. Has anyone seen this issue? Have any solutions been found? Error 1: When copying files after the PL attributes have been set by deduplication. "One or more items can't be copied to "Foler" because you don't have permissions to read them. ******************************************' Via the system.log, I am also seeing the following error when accessing these deduplicated file shares. The reparse point tag listed below is "IO_REPARSE_TAG_DEDUP" Reported error: "smbfs_nget: filename.ext - unknown reparse point tag 0x80000013"

  Read the article

• RTNETLINK answers: File exists... maybe because assigned a new mac adress

  - by steven

  I got a "RTNETLINK answers: File exists Failed to bring up eth0:1" on "ifup eth0:1". I suspect it happens because i assigned a new mac adress in my VM's network adapter. Can you tell me how to fix the issue? My configuration looks like this: # The loopback network interface auto lo iface lo inet loopback # The primary network interface auto eth0 allow-hotplug eth0 iface eth0 inet static address 192.168.1.80 netmask 255.255.255.0 gateway 192.168.1.1 dns-nameservers 192.168.1.1 # Alias being connected to 192.168.10.x Network auto eth0:1 allow-hotplug eth0:1 iface eth0:1 inet static address 192.168.10.83 netmask 255.255.255.0 gateway 192.168.10.10 dns-nameservers 192.168.10.1 Why do I get "RTNETLINK answer: File exists.." suddenly? I worked with this configuration before without problems. All i did in the past is to renew the adapters mac adress. At the moment I am connected to the 192.168.10.x Network and if I do /etc/init.d/networking stop /etc/init.d/networking start then i got "RTNETLINK [...] falied to bring up eth0:1" but the strage thing is that i am able to connect to 192.168.10.83 via ssh from my host machine. But I cannot reach the internet from the debian client. I hope it is clear what my problem is, now. update if i change my /etc/network/interfaces like this then "ifup eth0" fails, too with the same error! # The loopback network interface auto lo iface lo inet loopback # The primary network interface auto eth0 allow-hotplug eth0 iface eth0 inet static address 192.168.10.83 netmask 255.255.255.0 gateway 192.168.10.10 dns-nameservers 192.168.10.1 with verbose option enabled i got: Configuring interfache eth0=eth0 (inet) run-parts --verbose /etc/network/if-pre-up.d ip addr add 192.168.10.83/255.255.255.0 broadcast 192.168.10.255 dev eth0 label eth0 RTNETLINK answers: File exists Failed to bring up eth0. same if i type this manually: ip addr add 192.168.10.83/255.255.255.0 broadcast 192.168.10.255 dev eth0 label eth0

  Read the article

• Remote connection to a Windows 2008 Server Web edition

  - by Lorenzo

  Hello I have just installed Windows 2008 web server to have a development/test site on my office. In the test network I only have 2 machines: Windows server 2008 Web Edition Vista x64 client machine with Visual Studio The client and the server are networked using a NETGEAR router. I have enabled Remote desktop on the server and when I try to connect to it within the Vista client I get the credential window as in the following screenshot. But even if I write the correct credentials I am not able to remote login on the server. Where am I doing wrong? Update 1 I have even tried to create a folder share on the server. But I am not able to access it for the same reason. User or password invalid it says. But this is impossible as I am logging in the server with the same credentials. Update 2 If I try to browse the network from the RDP client I receive a message saying that there are no server running Terminal Services in my network.... :O

  Read the article

• Getting prompted for password accessing page through script even when client and server are in same

  - by Munawar

  I'm trying to pull up an internal webpage in automated fashion using the methods in 'Internetexplorer.Application' using vbscript. But I'm getting prompted for password, although the client and the server both are in the same domain. Predictably when I manually try to access the web page, I don't have any problem. Only when I try using cscript.exe or iexplore.exe, I get prompted. I'm trying to automate some of the smoke test we do after a new build is deployed. But this password prompt is getting in the way. Following are the system specs Client machine - IE 7.0, OS is Windows server 2003 Server machine - Windows Server 2008 Both are in the same domain. So far I've unsuccessfully tried following to automate the password input system.diagnostics.process.start var WinHttpReq = new ActiveXObject("WinHttp.WinHttpRequest.5.1"); WinHttpReq.Open("GET", "http://website", false); WinHttpReq.SetCredentials("username", "password", 0); Nothing seems to work I checked in IIS. we have only anonymous and forms authentication enabled Is there any configuration setting in the client machine that can be tweaked to bypass this, although I'd hate to do it since you step on the toes of twenty people trying to do that. Preferable way would be to programmatically input it if its possible. Also, if you can suggest a more appropriate forum, that'd be great too. Please help.

  Read the article

• Amazon EC2 Nat Instance - goes out but not back in

  - by nocode

  I've followed Amazon's steps and list what I've done. I've created 6 subnets (4 private SN1: 10.50.1.0/24, SN2: 10.50.2.0/24, SN3: 10.50.3.0/24, SN4: 10.50.4.0/24) and 2 public (SN5: 10.50.101.0/24 and SN6: 10.50.102.0/24) -I have a Bastion host and a NAT instance on SN5 and assigned EIP's to both. I created a test instance on SN1. edit: -NAT instance has source/destination check disabled -On the NAT instance, I had enabled the following commands to be bootstrapped: echo 1 > /proc/sys/net/ipv4/ip_forward iptables -t nat -A POSTROUTING -s 10.0.0.0/16 -j MASQUERADE -In my VPC, the private subnets have their own route table and configured 0.0.0.0/0 to the NAT instance with 4 subnets being associated with the route table. I have a second route table for my public subnets and 0.0.0.0/16 is pointed towards the IGW (with the other 2 subnets associated with it). -For Security Groups, I have the NAT instance accepting all traffic on each of the 4 subnets and all OUTBOUND traffic is allowed. For my test server, I have allowed all outbound access and have allowed all traffic from the public subnet of the NAT host. I can ping internally with no issues. On my test instance, if I try to ping google.com, DNS resolves however I don't get a reply back. On my NAT instance, I run a tcpdump and can see the request being requested to google.com but it's not sending the reply back. My NAT host can ping and receive a reply from google. From the test host, when I ping the NAT instance, the tcpdump shows a request and receive. Is there something I'm missing? EDIT: I've figured it out - I had to save the iptable config and restart the service.

  Read the article

• Why does Internet Explorer sometimes fail to connect to anything until I restart it?

  - by cletus

  IE has an annoying problem on my PC (XP SP3). I start it and try to go to Google (for example) and it'll sit there saying "Connecting" but nothing will happen and it doesn't matter how many times I try, it won't connect to anything. I discovered that if I kill IE and restart it then it might start working (and then it'll work every time). It might takes 3-4 restarts (of IE, not the PC) to get a working IE. Now I wouldn't normally care about this since I use Chrome but a lot of things use IE by default like Windows Update and the online help in Office 2003 so I would like to fix it. Interestingly, my work laptop, which is running Windows 7 RC 64-bit, has exactly the same problem (completely different network and everything). I'm utterly convinced it's not a network or hardware problem but some software problem. Edit: More info. It's IE8; No add-ons; Automatically detect settings is not enabled. It is set to "Never dial a connection".

  Read the article

• Can't mv files between directories on vsftpd

  - by frankyue

  I enabled this in vsftpd.conf chroot_local_user=YES chroot_list_enable=YES chroot_list_file=/etc/vsftpd.chroot_list user_config_dir=/etc/vsftpd_user_conf and here is the user set in vsftpd_user_conf dirctory ftpupload : local_root=/mnt/upload But /mnt/upload is mounted from another directory /mnt/upload on /opt/upload type none (rw,bind) Here is the list in /mn/upload rough_images/ shoes-pentland/ vendor-upload/ shooting/ Additional, the shooting/ directory is mounted from another place /mnt/upload/shooting on /mnt/shooting none (rw,bind) Now here is the problem. When I use the ftp client to move the files between the directories but failed .Files can moved between any directories except the shooting one. The permission is right . I can move any files between this directories successful by using su ftpupload. It means the vsftpd didn't support the mount bind? Here is the vsftpd.conf listen=YES anonymous_enable=NO local_enable=YES write_enable=YES local_umask=000 dirmessage_enable=YES use_localtime=YES xferlog_enable=YES connect_from_port_20=YES chown_uploads=YES chown_username=app xferlog_std_format=NO log_ftp_protocol=YES chroot_local_user=YES chroot_list_enable=YES chroot_list_file=/etc/vsftpd.chroot_list user_config_dir=/etc/vsftpd_user_conf ls_recurse_enable=YES secure_chroot_dir=/var/run/vsftpd/empty pam_service_name=vsftpd pasv_enable=YES pasv_max_port=*** pasv_min_port=*** port_enable=YES pasv_address=*** virtual_use_local_privs=YES tcp_wrappers=YES and here is the mtab: /mnt/upload /opt/upload none rw,bind 0 0 /mnt/upload/shooting /mnt/shooting none rw,bind 0 0 all of the permissions under the /mnt/upload are the same: drwxrwxrwx * ftpupload app

  Read the article

• HP DL185 - very slow disk read speed

  - by fistameeny

  Hi, I have a HP DL185 G6 Server (12 disk model) with the following spec: Quad Core Xeon 2.27GHz 6GB RAM HP P212 RAID controller with battery backup 2 x 128GB 15K SAS 3.5" (RAID-1 for the operating system) 4 x 750GB 7.5K SAS 3.5" (RAID-5 for the data, 2TB usable space) The operating system is Ubuntu Server 9.10. Both drives have been formatted as EXT4. We are finding that read speed of the RAID-5 array is poor. Disk test results below: sudo hdparm -tT /dev/cciss/c0d1p1 /dev/cciss/c0d1p1: Timing cached reads: 15284 MB in 2.00 seconds = 7650.18 MB/sec Timing buffered disk reads: 74 MB in 3.02 seconds = 24.53 MB/sec For info, the RAID-1 array performs as follows: sudo hdparm -tT /dev/cciss/c0d0p1 /dev/cciss/c0d0p1: Timing cached reads: 15652 MB in 2.00 seconds = 7834.26 MB/sec Timing buffered disk reads: 492 MB in 3.01 seconds = 163.46 MB/sec We thought this was because with no battery, read/write cache is disabled. We have bought and installed the battery backup and have used the HP bootable CD to change the cache settings to 50% read / 50% write and check cache is enabled on the drives and the controller. Is there something I'm missing?

  Read the article

< Previous Page | 197 198 199 200 201 202 203 204 205 206 207 208  | Next Page >