Search Results

Search found 18773 results on 751 pages for 'router configuration'.

Page 202/751 | < Previous Page | 198 199 200 201 202 203 204 205 206 207 208 209  | Next Page >

  • GRE keepalive with Linux and RouterOS

    - by eri
    I have a Linux host and couple of routerboadrs. I created a GRE tunnel, but Linux does not answer keepalive packages. Then router mark gre connection as unreachable, so I cant send to Linux host from router subnet. If linux sends something into tunnel (ping, etc.) - RouterOS mark connection as reacheble. Second and next packages routed nicely until one minute idle (no traffic). Tunnel in linux a make in this way: remote=x.x.x.x dev=gre21 network=10.21.0.0/16 ip tunnel add ${dev} mode gre remote ${remote} ttl 255 ip addr add 172.16.1.1/24 peer 172.16.1.21 dev ${dev} ip link set ${dev} up ip route add ${network} dev ${dev} And ip l: 14: gre21: <POINTOPOINT,NOARP,UP,LOWER_UP> mtu 1476 qdisc noqueue state UNKNOWN link/gre 0.0.0.0 peer 109.60.170.15 How to set state "running"? How to keep alive tunnel? Ping in cron?

    Read the article

  • Fedora 12 Wireless problems (Intel Wireless 4965AGN Card)

    - by Ninefingers
    Hi All, I'm having an interesting experience with my wireless card at the moment. Basically, it does like this: I connect to the local wireless network (netgear router) It works, briefly, allowing me to browse a webpage or maybe two, if I'm lucky. It then stops working / sending any packets, whilst reported still connected. Now, me being me I've had a look to see what I can find. wpa_supplicant.log looks like this: Trying to associate with valid_mac:a2:30 (SSID='vennardwireless' freq=2462 MHz) Associated with valid_mac:a2:30 WPA: Key negotiation completed with valid_mac:a2:30 [PTK=CCMP GTK=TKIP] CTRL-EVENT-CONNECTED - Connection to valid_mac:a2:30 completed (reauth) [id=0 id_str=] CTRL-EVENT-DISCONNECTED - Disconnect event - remove keys So that's working fine. dmesg | grep "*iwl*" spits out this: iwlagn: Intel(R) Wireless WiFi Link AGN driver for Linux, 1.3.27kds iwlagn: Copyright(c) 2003-2009 Intel Corporation iwlagn 0000:03:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17 iwlagn 0000:03:00.0: setting latency timer to 64 iwlagn 0000:03:00.0: Detected Intel Wireless WiFi Link 4965AGN REV=0x4 iwlagn 0000:03:00.0: Tunable channels: 13 802.11bg, 19 802.11a channels iwlagn 0000:03:00.0: irq 32 for MSI/MSI-X phy0: Selected rate control algorithm 'iwl-agn-rs' iwlagn 0000:03:00.0: firmware: requesting iwlwifi-4965-2.ucode iwlagn 0000:03:00.0: loaded firmware version 228.61.2.24 Registered led device: iwl-phy0::radio Registered led device: iwl-phy0::assoc Registered led device: iwl-phy0::RX Registered led device: iwl-phy0::TX iwlagn 0000:03:00.0: iwl_tx_agg_start on ra = 00:24:b2:32:a3:30 tid = 0 iwlagn 0000:03:00.0: iwl_tx_agg_start on ra = 00:24:b2:32:a3:30 tid = 0 So that's working too. I can also ping 192.168.0.1 -I wlan0 and arping 192.168.0.1 -I wlan0 the router until the network falls over. uname -r:2.6.32.10-90.fc12.x86_64. Laptop is a Core2 Duo (2Ghz) with 3GB RAM. Other symptoms I've noticed are that wireshark freezes when I capture on the "broken" interface until I disconnect. Am using networkmanager as per normal. Stupidly, I can connect to the same router via eth0/a cat6 cable just fine. Everyone else can connect to the AP fine (from Windows). Yes, I'm sat right next to it and not trying to access a hotspot the other side of the world. Any ideas? Is this a broken update? (I intend to reboot and test an older kernel later)? Anyone else come across this? Edit: iwconfig wlan0 rate auto is the settings I'm using for rates. Also, according to networkmanager the network is still connected. Thanks for any pointers / advice.

    Read the article

  • Assigning a home DNS to be secondary only?

    - by Sanarothe
    Hi. I have a small domain lab set up at home, including DNS/DHCP on the Win2008 server. I'd like to be able to refer to my domain clients by name, but I find that I get a slowdown when using an internal DNS. Win DNS refers to my ISP's upstream dns (I also tried Google's DNS servers for a little while) but it feels like there's an extra couple seconds for each request when I'm using anything except the DNS servers fetched via DHCP from my ISP. I tried adding my local DNS to my router's DHCP (Need to use router to fetch DHCP info from ISP, even though none of it ever changes, since I'm behind NAT) So, my question is: Is there any way to set my internal DNS server to be secondary to a dynamically retrieved upstream DNS? I want the internal server to be queried only if the ISP dns fails, or to be queried only for a certain TLD (.iv right now. I guess for best practices I should change it to .internal)

    Read the article

  • SQL Server Express 2008 R2 Installation error at Windows 7

    - by Shai Sherman
    Hello, I created install script that will install SQL Server 2008 R2 on windows XP SP3, windows vista and windows 7. One of the command that i used in the installation is for silent installation of SQL Server 2008 R2. When i install it on windows XP everything works just fine but when i try to install it on Windows 7 i get an error. What am I doing wrong? Here is the command line that i use: "Setup.exe /ConfigurationFile=Mysetup.ini" Mysetup.ini file: -------------------------------------Start of ini file --------------------------------- ;SQL SERVER 2008 R2 Configuration File ;Version 1.0, 5 May 2010 ; [SQLSERVER2008] ; Specify the Instance ID for the SQL Server features you have specified. SQL Server directory structure, registry structure, and service names will reflect the instance ID of the SQL Server instance. INSTANCEID="MSSQLSERVER" ; Specifies a Setup work flow, like INSTALL, UNINSTALL, or UPGRADE. This is a required parameter. ACTION="Install" ; Specifies features to install, uninstall, or upgrade. The list of top-level features include SQL, AS, RS, IS, and Tools. The SQL feature will install the database engine, replication, and full-text. The Tools feature will install Management Tools, Books online, Business Intelligence Development Studio, and other shared components. FEATURES=SQLENGINE ; Displays the command line parameters usage HELP="False" ; Specifies that the detailed Setup log should be piped to the console. INDICATEPROGRESS="False" ; Setup will not display any user interface. QUIET="False" ; Setup will display progress only without any user interaction. QUIETSIMPLE="True" ; Specifies that Setup should install into WOW64. This command line argument is not supported on an IA64 or a 32-bit system. ;X86="False" ; Specifies the path to the installation media folder where setup.exe is located. ;MEDIASOURCE="z:\" ; Detailed help for command line argument ENU has not been defined yet. ENU="True" ; Parameter that controls the user interface behavior. Valid values are Normal for the full UI, and AutoAdvance for a simplied UI. ; UIMODE="Normal" ; Specify if errors can be reported to Microsoft to improve future SQL Server releases. Specify 1 or True to enable and 0 or False to disable this feature. ERRORREPORTING="False" ; Specify the root installation directory for native shared components. ;INSTALLSHAREDDIR="D:\Program Files\Microsoft SQL Server" ; Specify the root installation directory for the WOW64 shared components. ;INSTALLSHAREDWOWDIR="D:\Program Files (x86)\Microsoft SQL Server" ; Specify the installation directory. ;INSTANCEDIR="D:\Program Files\Microsoft SQL Server" ; Specify that SQL Server feature usage data can be collected and sent to Microsoft. Specify 1 or True to enable and 0 or False to disable this feature. SQMREPORTING="False" ; Specify a default or named instance. MSSQLSERVER is the default instance for non-Express editions and SQLExpress for Express editions. This parameter is required when installing the SQL Server Database Engine (SQL), Analysis Services (AS), or Reporting Services (RS). INSTANCENAME="SQLEXPRESS" SECURITYMODE=SQL SAPWD=SystemAdmin ; Agent account name AGTSVCACCOUNT="NT AUTHORITY\NETWORK SERVICE" ; Auto-start service after installation. AGTSVCSTARTUPTYPE="Manual" ; Startup type for Integration Services. ;ISSVCSTARTUPTYPE="Automatic" ; Account for Integration Services: Domain\User or system account. ;ISSVCACCOUNT="NT AUTHORITY\NetworkService" ; Controls the service startup type setting after the service has been created. ;ASSVCSTARTUPTYPE="Automatic" ; The collation to be used by Analysis Services. ;ASCOLLATION="Latin1_General_CI_AS" ; The location for the Analysis Services data files. ;ASDATADIR="Data" ; The location for the Analysis Services log files. ;ASLOGDIR="Log" ; The location for the Analysis Services backup files. ;ASBACKUPDIR="Backup" ; The location for the Analysis Services temporary files. ;ASTEMPDIR="Temp" ; The location for the Analysis Services configuration files. ;ASCONFIGDIR="Config" ; Specifies whether or not the MSOLAP provider is allowed to run in process. ;ASPROVIDERMSOLAP="1" ; A port number used to connect to the SharePoint Central Administration web application. ;FARMADMINPORT="0" ; Startup type for the SQL Server service. SQLSVCSTARTUPTYPE="Automatic" ; Level to enable FILESTREAM feature at (0, 1, 2 or 3). FILESTREAMLEVEL="0" ; Set to "1" to enable RANU for SQL Server Express. ENABLERANU="1" ; Specifies a Windows collation or an SQL collation to use for the Database Engine. SQLCOLLATION="SQL_Latin1_General_CP1_CI_AS" ; Account for SQL Server service: Domain\User or system account. SQLSVCACCOUNT="NT Authority\System" ; Default directory for the Database Engine user databases. ;SQLUSERDBDIR="K:\Microsoft SQL Server\MSSQL\Data" ; Default directory for the Database Engine user database logs. ;SQLUSERDBLOGDIR="L:\Microsoft SQL Server\MSSQL\Data\Logs" ; Directory for Database Engine TempDB files. ;SQLTEMPDBDIR="T:\Microsoft SQL Server\MSSQL\Data" ; Directory for the Database Engine TempDB log files. ;SQLTEMPDBLOGDIR="T:\Microsoft SQL Server\MSSQL\Data\Logs" ; Provision current user as a Database Engine system administrator for SQL Server 2008 R2 Express. ADDCURRENTUSERASSQLADMIN="True" ; Specify 0 to disable or 1 to enable the TCP/IP protocol. TCPENABLED="1" ; Specify 0 to disable or 1 to enable the Named Pipes protocol. NPENABLED="0" ; Startup type for Browser Service. BROWSERSVCSTARTUPTYPE="Automatic" ; Specifies how the startup mode of the report server NT service. When ; Manual - Service startup is manual mode (default). ; Automatic - Service startup is automatic mode. ; Disabled - Service is disabled ;RSSVCSTARTUPTYPE="Automatic" ; Specifies which mode report server is installed in. ; Default value: “FilesOnly” ;RSINSTALLMODE="FilesOnlyMode" ; Accept SQL Server 2008 R2 license terms IACCEPTSQLSERVERLICENSETERMS="TRUE" ;setup.exe /CONFIGURATIONFILE=Mysetup.ini /INDICATEPROGRESS --------------------------- End of ini file ------------------------------------- And i get this error: 2010-08-31 18:05:53 Slp: Error result: -2068119551 2010-08-31 18:05:53 Slp: Result facility code: 1211 2010-08-31 18:05:53 Slp: Result error code: 1 2010-08-31 18:05:53 Slp: Sco: Attempting to create base registry key HKEY_LOCAL_MACHINE, machine 2010-08-31 18:05:53 Slp: Sco: Attempting to open registry subkey 2010-08-31 18:05:53 Slp: Sco: Attempting to open registry subkey Software\Microsoft\PCHealth\ErrorReporting\DW\Installed 2010-08-31 18:05:53 Slp: Sco: Attempting to get registry value DW0200 2010-08-31 18:05:53 Slp: Submitted 1 of 1 failures to the Watson data repository What the meaning of this? What do i need to do to fix that problem? Here is the Summary file: Overall summary: Final result: SQL Server installation failed. To continue, investigate the reason for the failure, correct the problem, uninstall SQL Server, and then rerun SQL Server Setup. Exit code (Decimal): -2068119551 Exit facility code: 1211 Exit error code: 1 Exit message: SQL Server installation failed. To continue, investigate the reason for the failure, correct the problem, uninstall SQL Server, and then rerun SQL Server Setup. Start time: 2010-08-31 18:03:44 End time: 2010-08-31 18:05:51 Requested action: Install Log with failure: C:\Program Files\Microsoft SQL Server\100\Setup Bootstrap\Log\20100831_180236\Detail.txt Exception help link: http%3a%2f%2fgo.microsoft.com%2ffwlink%3fLinkId%3d20476%26ProdName%3dMicrosoft%2bSQL%2bServer%26EvtSrc%3dsetup.rll%26EvtID%3d50000%26ProdVer%3d10.50.1600.1%26EvtType%3d0x6121810A%400xC24842DB Machine Properties: Machine name: NVR Machine processor count: 2 OS version: Windows 7 OS service pack: OS region: United States OS language: English (United States) OS architecture: x86 Process architecture: 32 Bit OS clustered: No Product features discovered: Product Instance Instance ID Feature Language Edition Version Clustered Package properties: Description: SQL Server Database Services 2008 R2 ProductName: SQL Server 2008 R2 Type: RTM Version: 10 SPLevel: 0 Installation location: C:\Disk1\setupsql\x86\setup\ Installation edition: EXPRESS User Input Settings: ACTION: Install ADDCURRENTUSERASSQLADMIN: True AGTSVCACCOUNT: NT AUTHORITY\NETWORK SERVICE AGTSVCPASSWORD: * AGTSVCSTARTUPTYPE: Disabled ASBACKUPDIR: Backup ASCOLLATION: Latin1_General_CI_AS ASCONFIGDIR: Config ASDATADIR: Data ASDOMAINGROUP: ASLOGDIR: Log ASPROVIDERMSOLAP: 1 ASSVCACCOUNT: ASSVCPASSWORD: * ASSVCSTARTUPTYPE: Automatic ASSYSADMINACCOUNTS: ASTEMPDIR: Temp BROWSERSVCSTARTUPTYPE: Automatic CONFIGURATIONFILE: C:\Program Files\Microsoft SQL Server\100\Setup Bootstrap\Log\20100831_180236\ConfigurationFile.ini CUSOURCE: ENABLERANU: True ENU: True ERRORREPORTING: False FARMACCOUNT: FARMADMINPORT: 0 FARMPASSWORD: * FEATURES: SQLENGINE FILESTREAMLEVEL: 0 FILESTREAMSHARENAME: FTSVCACCOUNT: FTSVCPASSWORD: * HELP: False IACCEPTSQLSERVERLICENSETERMS: True INDICATEPROGRESS: False INSTALLSHAREDDIR: C:\Program Files\Microsoft SQL Server\ INSTALLSHAREDWOWDIR: C:\Program Files\Microsoft SQL Server\ INSTALLSQLDATADIR: INSTANCEDIR: C:\Program Files\Microsoft SQL Server\ INSTANCEID: MSSQLSERVER INSTANCENAME: SQLEXPRESS ISSVCACCOUNT: NT AUTHORITY\NetworkService ISSVCPASSWORD: * ISSVCSTARTUPTYPE: Automatic NPENABLED: 0 PASSPHRASE: * PCUSOURCE: PID: * QUIET: False QUIETSIMPLE: True ROLE: AllFeatures_WithDefaults RSINSTALLMODE: FilesOnlyMode RSSVCACCOUNT: NT AUTHORITY\NETWORK SERVICE RSSVCPASSWORD: * RSSVCSTARTUPTYPE: Automatic SAPWD: * SECURITYMODE: SQL SQLBACKUPDIR: SQLCOLLATION: SQL_Latin1_General_CP1_CI_AS SQLSVCACCOUNT: NT Authority\System SQLSVCPASSWORD: * SQLSVCSTARTUPTYPE: Automatic SQLSYSADMINACCOUNTS: SQLTEMPDBDIR: SQLTEMPDBLOGDIR: SQLUSERDBDIR: SQLUSERDBLOGDIR: SQMREPORTING: False TCPENABLED: 1 UIMODE: AutoAdvance X86: False Configuration file: C:\Program Files\Microsoft SQL Server\100\Setup Bootstrap\Log\20100831_180236\ConfigurationFile.ini Detailed results: Feature: Database Engine Services Status: Failed: see logs for details MSI status: Passed Configuration status: Failed: see details below Configuration error code: 0x0A2FBD17@1211@1 Configuration error description: The process cannot access the file because it is being used by another process. Configuration log: C:\Program Files\Microsoft SQL Server\100\Setup Bootstrap\Log\20100831_180236\Detail.txt Rules with failures: Global rules: Scenario specific rules: Rules report file: C:\Program Files\Microsoft SQL Server\100\Setup Bootstrap\Log\20100831_180236\SystemConfigurationCheck_Report.htm What should I do and why does this problem occur? Thanks , Shai.

    Read the article

  • Could not find schema information for the element 'castle'.

    - by Richard77
    Hello! I'm creating a Custom tag in my web.config. I first wrote the following entry under the configSections section. <section name="castle" type="Castle.Windsor.Configuration.AppDomain.CastleSectionHandler, Castle.Windsor" /> But, when I try to create a castle node inside the configuration node as below <castle> <components> </components> </castle> I get the following error message:"*Could not find schema information for the element 'castle*'." "*Could not find schema information for the element 'components'***." Am I missing something? I can't find why. And, if I run the application anyway, I get the following error "Could not find section 'Castle' in the configuration file associated with this domain." Ps.// The sample comes from "Pro ASP.NET MVC Framework"/Steven Sanderson/APress ISBN-13 (pbk): 978-1-4302-1007-8" on page 99. Thank you for the help ============================================================ Since I believe to have done exactly what's said in the book and did not succed, I ask the same question in different terms. How do I add a new node using the above information? ============================================================================= Thank you. I did what you said and do not have the two warnings. However, I've go a big new warning: "The element 'configuration' in namespace 'MyWindsorSchema' has invalid child element 'configSections' in namespace 'MyWindsorSchema'. List of possible elements expected: 'include, properties, facilities, components' in namespace 'MyWindsorSchema'."

    Read the article

  • properties-maven-plugin: Error loading properties-file

    - by yournamehere
    I want to extract all the properties from my pom.xml into a properties-file. These are the common properties like dependency-versions, plugin-versions and directories. I'm using the properties-maven-plugin, but its not working as i want it to. The essential part of my pom.xml: <plugin> <groupId>org.codehaus.mojo</groupId> <artifactId>properties-maven-plugin</artifactId> <version>1.0-alpha-1</version> <executions> <execution> <phase>initialize</phase> <goals> <goal>read-project-properties</goal> </goals> <configuration> <files> <file>${basedir}/pom.properties</file> </files> </configuration> </execution> </executions> </plugin> Now when i run "mvn properties:read-project-properties" i get the following error: [INFO] One or more required plugin parameters are invalid/missing for 'properties:read-project-properties' [0] Inside the definition for plugin 'properties-maven-plugin' specify the following: <configuration> ... <files>VALUE</files> </configuration>. The pom.properties-file is located in the same dir as the pom.xml. What can i do to let the properties-maven-plugin read my properties-file?

    Read the article

  • cxf jaxws with spring on gwt 2.0

    - by Karl
    Hi, I'm trying to use an application which uses cxf-jaxws in bean definition: <beans xmlns="http://www.springframework.org/schema/beans" xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance" xmlns:sec="http://cxf.apache.org/configuration/security" xmlns:jaxws="http://cxf.apache.org/jaxws" xmlns:util="http://www.springframework.org/schema/util" xsi:schemaLocation="http://www.springframework.org/schema/beans http://www.springframework.org/schema/beans/spring-beans-2.0.xsd http://cxf.apache.org/configuration/security http://cxf.apache.org/schemas/configuration/security.xsd http://cxf.apache.org/jaxws http://cxf.apache.org/schemas/jaxws.xsd http://www.springframework.org/schema/util http://www.springframework.org/schema/util/spring-util-2.0.xsd"> however in combination with the jetty from gwt 2.0 development shell my context doesn't load and I get this exception: org.springframework.web.context.ContextLoader: Context initialization failed org.springframework.beans.factory.parsing.BeanDefinitionParsingException: Configuration problem: Unable to locate Spring NamespaceHandler for XML schema namespace [http://cxf.apache.org/jaxws] enter code hereOffending resource: class path resource [bean_definition.xml] My project is maven-based and I got cxf-rt-frontend-jaxws which contains the namespacehandler and spring.handlers on the classpath. I added cxf-transports-http-jetty.jar as well. Has anyone experienced this kind of problem and found a solution? It seems to be a classpath issue, added the cxf-rt-frontend-jaxws.jar by hand and it works... Somehow the maven dependency doesn't get added to the classpath. Thanks in advance, karl

    Read the article

  • DD-WRT with native IPv6

    - by Matt
    My ISP provides native IPv6 support (ie. I can plug in my computer straight into the WAN and get an IPv6 address). However I can not get this working on DD-WRT. When I enable IPv6 and radvd in DD-WRT, the router gets in IPv6 address, but the devices on my LAN do not. I tried looking at the DD-WRT wiki, but this only displayed instructions for tunneling or other methods where native support isn't available. I found a small amount of sites thorough searching, but none of the methods these sites described gave my computers each a global IPv6 address. In addition, SSHing into the router using ping6 on sites such as ipv6.google.com causes "host unreachable" errors. Has anyone using DD-WRT configured a successful setup with native IPv6? I am using a Netgear WNDR3700 v2, with DD-WRT build 17201

    Read the article

  • Maven WTP webapp with maven-eclipse-plugin but without m2eclipse

    - by chrsk
    I use the eclipse:eclipse goal to generate an Eclipse Project environment. The deployment works fine. The goal creates the var classpath entries for all needed dependencies. With m2eclipse there was the Maven Container which defines an export folder which was WEB-INF/lib for me. But i don't want to rely on m2eclipse so i don't want to use it anymore. the class path entries which are generated by eclipse:eclipse goal don't have such a export folder. While booting the servlet container with WTP it publishes all resources and classes except the libraries to the context. Whats missing to publish the needed libs, or isn't that possible without m2eclipse integration? IDE Configuration Eclipse 3.5 JEE Galileo Maven 2 m2eclipse The maven-eclipse-plugin configuration <plugin> <groupId>org.apache.maven.plugins</groupId> <artifactId>maven-eclipse-plugin</artifactId> <version>2.8</version> <configuration> <projectNameTemplate>opensaga-[artifactId]</projectNameTemplate> <useProjectReferences>false</useProjectReferences> <downloadSources>false</downloadSources> <downloadJavadocs>false</downloadJavadocs> <wtpmanifest>true</wtpmanifest> <wtpversion>2.0</wtpversion> <wtpapplicationxml>true</wtpapplicationxml> <wtpContextName>opensaga-[artifactId]</wtpContextName> <additionalProjectFacets> <jst.java>5.0</jst.java> <jst.web>2.3</jst.web> </additionalProjectFacets> </configuration> </plugin>

    Read the article

  • DD-WRT VPN error 800?

    - by MrZombie
    I have set up a router with DD-WRT Mega on my Asus WL-500gP V2, and I can't connect to the VPN service. I have set it up according to the configuration on the DD-WRT wiki, so the server IP is set to 192.168.1.1, which is the address of the router, and I set up the client addresses to be 192.168.1.20-29. My chap secrets are set up correctly, and still, I get an error 800 on windows XP. As far as I can tell, it means my network is unreachable. The server responds to ping.

    Read the article

  • setup Zyxel USG 20W as L2TP VPN Server

    - by Massimo
    I've a Zywall USG 20W (wireless disabled) behind a router supplied by the ISP. All ports (both TCP and UDP) on the ISP router are forwarded to the 20W. I'm trying to configure an L2TP VPN to be used by Windows Xp / 7 with Microsoft native client. This was working before with a different firewall, so I'm pretty sure that all the required packets are flowing to the 20W. I followed a tutorial from the italian Zyxel Website, but I cannot get the VPN to work. Always cannot pass phase 2, and I see the following on the log: [ID]: Tunnel [Default_L2TP_VPN_Connection] Phase 2 local policy mismatch Phase 1 goes fine. In Windows the error is always 788. This happens regardless the proposals I set in the phase 1 and 2 setting. What should I check ? Is there any way to get more detailed diagnostic info (policy mismatch is too generic) ? Thanks a lot to whom may help. Massimo.

    Read the article

  • testing Clojure in Maven

    - by Ralph
    I am new at Maven and even newer at Clojure. As an exercise to learn the language, I am writing a spider solitaire player program. I also plan on writing a similar program in Scala to compare the implementations (see my post http://stackoverflow.com/questions/2571267/modern-java-alternatives-closed). I have configured a Maven directory structure containing the usual src/main/clojure and src/test/clojure directories. My pom.xml file includes the clojure-maven-plugin. When I run "mvn test", it displays "No tests to run", despite my having test code in the src/test/clojure directory. As I misnaming something? Here is my pom.xml file: <?xml version="1.0" encoding="UTF-8"?> <project xmlns="http://maven.apache.org/POM/4.0.0" xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance" xsi:schemaLocation="http://maven.apache.org/POM/4.0.0 http://maven.apache.org/xsd/maven-4.0.0.xsd"> <modelVersion>4.0.0</modelVersion> <groupId>SpiderPlayer</groupId> <artifactId>SpiderPlayer</artifactId> <version>1.0.0-SNAPSHOT</version> <inceptionYear>2010</inceptionYear> <packaging>jar</packaging> <properties> <maven.build.timestamp.format>yyMMdd.HHmm</maven.build.timestamp.format> <main.dir>org/dogdaze/spider_player</main.dir> <main.package>org.dogdaze.spider_player</main.package> <main.class>${main.package}.Main</main.class> </properties> <build> <sourceDirectory>src/main/clojure</sourceDirectory> <testSourceDirectory>src/main/clojure</testSourceDirectory> <plugins> <plugin> <groupId>com.theoryinpractise</groupId> <artifactId>clojure-maven-plugin</artifactId> <version>1.3.1</version> </plugin> <plugin> <groupId>org.apache.maven.plugins</groupId> <artifactId>maven-antrun-plugin</artifactId> <version>1.3</version> <executions> <execution> <goals> <goal>run</goal> </goals> <phase>generate-sources</phase> <configuration> <tasks> <echo file="${project.build.sourceDirectory}/${main.dir}/Version.clj" message="(ns ${main.package})${line.separator}"/> <echo file="${project.build.sourceDirectory}/${main.dir}/Version.clj" append="true" message="(def version &quot;${maven.build.timestamp}&quot;)${line.separator}"/> </tasks> </configuration> </execution> </executions> </plugin> <plugin> <groupId>org.apache.maven.plugins</groupId> <artifactId>maven-assembly-plugin</artifactId> <version>2.1</version> <executions> <execution> <goals> <goal>single</goal> </goals> <phase>package</phase> <configuration> <descriptorRefs> <descriptorRef>jar-with-dependencies</descriptorRef> </descriptorRefs> <archive> <manifest> <mainClass>${main.class}</mainClass> </manifest> </archive> </configuration> </execution> </executions> </plugin> <plugin> <groupId>org.apache.maven.plugins</groupId> <artifactId>maven-surefire-plugin</artifactId> <configuration> <redirectTestOutputToFile>true</redirectTestOutputToFile> <skipTests>false</skipTests> <skip>false</skip> </configuration> <executions> <execution> <id>surefire-it</id> <phase>integration-test</phase> <goals> <goal>test</goal> </goals> <configuration> <skip>false</skip> </configuration> </execution> </executions> </plugin> </plugins> </build> <dependencies> <dependency> <groupId>commons-cli</groupId> <artifactId>commons-cli</artifactId> <version>1.2</version> <scope>compile</scope> </dependency> </dependencies> </project> Here is my Clojure source file (src/main/clojure/org/dogdaze/spider_player/Deck.clj): ; Copyright 2010 Dogdaze (ns org.dogdaze.spider_player.Deck (:use [clojure.contrib.seq-utils :only (shuffle)])) (def suits [:clubs :diamonds :hearts :spades]) (def ranks [:ace :two :three :four :five :six :seven :eight :nine :ten :jack :queen :king]) (defn suit-seq "Return 4 suits: if number-of-suits == 1: :clubs :clubs :clubs :clubs if number-of-suits == 2: :clubs :diamonds :clubs :diamonds if number-of-suits == 4: :clubs :diamonds :hearts :spades." [number-of-suits] (take 4 (cycle (take number-of-suits suits)))) (defstruct card :rank :suit) (defn unshuffled-deck "Create an unshuffled deck containing all cards from the number of suits specified." [number-of-suits] (for [rank ranks suit (suit-seq number-of-suits)] (struct card rank suit))) (defn deck "Create a shuffled deck containing all cards from the number of suits specified." [number-of-suits] (shuffle (unshuffled-deck number-of-suits))) Here is my test case (src/test/clojure/org/dogdaze/spider_player/TestDeck.clj): ; Copyright 2010 Dogdaze (ns org.dogdaze.spider_player (:use clojure.set clojure.test org.dogdaze.spider_player.Deck)) (deftest test-suit-seq (is (= (suit-seq 1) [:clubs :clubs :clubs :clubs])) (is (= (suit-seq 2) [:clubs :diamonds :clubs :diamonds])) (is (= (suit-seq 4) [:clubs :diamonds :hearts :spades]))) (def one-suit-deck [{:rank :ace, :suit :clubs} {:rank :ace, :suit :clubs} {:rank :ace, :suit :clubs} {:rank :ace, :suit :clubs} {:rank :two, :suit :clubs} {:rank :two, :suit :clubs} {:rank :two, :suit :clubs} {:rank :two, :suit :clubs} {:rank :three, :suit :clubs} {:rank :three, :suit :clubs} {:rank :three, :suit :clubs} {:rank :three, :suit :clubs} {:rank :four, :suit :clubs} {:rank :four, :suit :clubs} {:rank :four, :suit :clubs} {:rank :four, :suit :clubs} {:rank :five, :suit :clubs} {:rank :five, :suit :clubs} {:rank :five, :suit :clubs} {:rank :five, :suit :clubs} {:rank :six, :suit :clubs} {:rank :six, :suit :clubs} {:rank :six, :suit :clubs} {:rank :six, :suit :clubs} {:rank :seven, :suit :clubs} {:rank :seven, :suit :clubs} {:rank :seven, :suit :clubs} {:rank :seven, :suit :clubs} {:rank :eight, :suit :clubs} {:rank :eight, :suit :clubs} {:rank :eight, :suit :clubs} {:rank :eight, :suit :clubs} {:rank :nine, :suit :clubs} {:rank :nine, :suit :clubs} {:rank :nine, :suit :clubs} {:rank :nine, :suit :clubs} {:rank :ten, :suit :clubs} {:rank :ten, :suit :clubs} {:rank :ten, :suit :clubs} {:rank :ten, :suit :clubs} {:rank :jack, :suit :clubs} {:rank :jack, :suit :clubs} {:rank :jack, :suit :clubs} {:rank :jack, :suit :clubs} {:rank :queen, :suit :clubs} {:rank :queen, :suit :clubs} {:rank :queen, :suit :clubs} {:rank :queen, :suit :clubs} {:rank :king, :suit :clubs} {:rank :king, :suit :clubs} {:rank :king, :suit :clubs} {:rank :king, :suit :clubs}]) (def two-suits-deck [{:rank :ace, :suit :clubs} {:rank :ace, :suit :diamonds} {:rank :ace, :suit :clubs} {:rank :ace, :suit :diamonds} {:rank :two, :suit :clubs} {:rank :two, :suit :diamonds} {:rank :two, :suit :clubs} {:rank :two, :suit :diamonds} {:rank :three, :suit :clubs} {:rank :three, :suit :diamonds} {:rank :three, :suit :clubs} {:rank :three, :suit :diamonds} {:rank :four, :suit :clubs} {:rank :four, :suit :diamonds} {:rank :four, :suit :clubs} {:rank :four, :suit :diamonds} {:rank :five, :suit :clubs} {:rank :five, :suit :diamonds} {:rank :five, :suit :clubs} {:rank :five, :suit :diamonds} {:rank :six, :suit :clubs} {:rank :six, :suit :diamonds} {:rank :six, :suit :clubs} {:rank :six, :suit :diamonds} {:rank :seven, :suit :clubs} {:rank :seven, :suit :diamonds} {:rank :seven, :suit :clubs} {:rank :seven, :suit :diamonds} {:rank :eight, :suit :clubs} {:rank :eight, :suit :diamonds} {:rank :eight, :suit :clubs} {:rank :eight, :suit :diamonds} {:rank :nine, :suit :clubs} {:rank :nine, :suit :diamonds} {:rank :nine, :suit :clubs} {:rank :nine, :suit :diamonds} {:rank :ten, :suit :clubs} {:rank :ten, :suit :diamonds} {:rank :ten, :suit :clubs} {:rank :ten, :suit :diamonds} {:rank :jack, :suit :clubs} {:rank :jack, :suit :diamonds} {:rank :jack, :suit :clubs} {:rank :jack, :suit :diamonds} {:rank :queen, :suit :clubs} {:rank :queen, :suit :diamonds} {:rank :queen, :suit :clubs} {:rank :queen, :suit :diamonds} {:rank :king, :suit :clubs} {:rank :king, :suit :diamonds} {:rank :king, :suit :clubs} {:rank :king, :suit :diamonds}]) (def four-suits-deck [{:rank :ace, :suit :clubs} {:rank :ace, :suit :diamonds} {:rank :ace, :suit :hearts} {:rank :ace, :suit :spades} {:rank :two, :suit :clubs} {:rank :two, :suit :diamonds} {:rank :two, :suit :hearts} {:rank :two, :suit :spades} {:rank :three, :suit :clubs} {:rank :three, :suit :diamonds} {:rank :three, :suit :hearts} {:rank :three, :suit :spades} {:rank :four, :suit :clubs} {:rank :four, :suit :diamonds} {:rank :four, :suit :hearts} {:rank :four, :suit :spades} {:rank :five, :suit :clubs} {:rank :five, :suit :diamonds} {:rank :five, :suit :hearts} {:rank :five, :suit :spades} {:rank :six, :suit :clubs} {:rank :six, :suit :diamonds} {:rank :six, :suit :hearts} {:rank :six, :suit :spades} {:rank :seven, :suit :clubs} {:rank :seven, :suit :diamonds} {:rank :seven, :suit :hearts} {:rank :seven, :suit :spades} {:rank :eight, :suit :clubs} {:rank :eight, :suit :diamonds} {:rank :eight, :suit :hearts} {:rank :eight, :suit :spades} {:rank :nine, :suit :clubs} {:rank :nine, :suit :diamonds} {:rank :nine, :suit :hearts} {:rank :nine, :suit :spades} {:rank :ten, :suit :clubs} {:rank :ten, :suit :diamonds} {:rank :ten, :suit :hearts} {:rank :ten, :suit :spades} {:rank :jack, :suit :clubs} {:rank :jack, :suit :diamonds} {:rank :jack, :suit :hearts} {:rank :jack, :suit :spades} {:rank :queen, :suit :clubs} {:rank :queen, :suit :diamonds} {:rank :queen, :suit :hearts} {:rank :queen, :suit :spades} {:rank :king, :suit :clubs} {:rank :king, :suit :diamonds} {:rank :king, :suit :hearts} {:rank :king, :suit :spades}]) (deftest test-unshuffled-deck (is (= (unshuffled-deck 1) one-suit-deck)) (is (= (unshuffled-deck 2) two-suits-deck)) (is (= (unshuffled-deck 4) four-suits-deck))) (deftest test-shuffled-deck (is (= (set (deck 1)) (set one-suit-deck))) (is (= (set (deck 2)) (set two-suits-deck))) (is (= (set (deck 4)) (set four-suits-deck)))) (run-tests) Any idea why the test is not running? BTW, feel free to suggest improvements to the Clojure code. Thanks, Ralph

    Read the article

  • (Fluent) NHibernate Security Exception - ReflectionPermission

    - by PeterEysermans
    I've upgraded an ASP.Net Web application to the latest build of Fluent NHibernate (1.0.0.636) and the newest version of NHibernate (v2.1.2.4000). I've checked a couple of times that the application is running in Full trust. But I keep getting the following error: Security Exception Description: The application attempted to perform an operation not allowed by the security policy. To grant this application the required permission please contact your system administrator or change the application's trust level in the configuration file. Exception Details: System.Security.SecurityException: Request for the permission of type 'System.Security.Permissions.ReflectionPermission, mscorlib, Version=2.0.0.0, Culture=neutral, PublicKeyToken=b77a5c561934e089' failed. Source Error: An unhandled exception was generated during the execution of the current web request. Information regarding the origin and location of the exception can be identified using the exception stack trace below. Stack Trace: [SecurityException: Request for the permission of type 'System.Security.Permissions.ReflectionPermission, mscorlib, Version=2.0.0.0, Culture=neutral, PublicKeyToken=b77a5c561934e089' failed.] System.Security.CodeAccessSecurityEngine.Check(Object demand, StackCrawlMark& stackMark, Boolean isPermSet) +0 System.Security.CodeAccessPermission.Demand() +54 System.Reflection.Emit.DynamicMethod.PerformSecurityCheck(Type owner, StackCrawlMark& stackMark, Boolean skipVisibility) +269 System.Reflection.Emit.DynamicMethod..ctor(String name, Type returnType, Type[] parameterTypes, Type owner, Boolean skipVisibility) +81 NHibernate.Bytecode.Lightweight.ReflectionOptimizer.CreateDynamicMethod(Type returnType, Type[] argumentTypes) +165 NHibernate.Bytecode.Lightweight.ReflectionOptimizer.GenerateGetPropertyValuesMethod(IGetter[] getters) +383 NHibernate.Bytecode.Lightweight.ReflectionOptimizer..ctor(Type mappedType, IGetter[] getters, ISetter[] setters) +108 NHibernate.Bytecode.Lightweight.BytecodeProviderImpl.GetReflectionOptimizer(Type mappedClass, IGetter[] getters, ISetter[] setters) +52 NHibernate.Tuple.Component.PocoComponentTuplizer..ctor(Component component) +231 NHibernate.Tuple.Component.ComponentEntityModeToTuplizerMapping..ctor(Component component) +420 NHibernate.Tuple.Component.ComponentMetamodel..ctor(Component component) +402 NHibernate.Mapping.Component.BuildType() +38 NHibernate.Mapping.Component.get_Type() +32 NHibernate.Mapping.SimpleValue.IsValid(IMapping mapping) +39 NHibernate.Mapping.RootClass.Validate(IMapping mapping) +61 NHibernate.Cfg.Configuration.ValidateEntities() +220 NHibernate.Cfg.Configuration.Validate() +16 NHibernate.Cfg.Configuration.BuildSessionFactory() +39 FluentNHibernate.Cfg.FluentConfiguration.BuildSessionFactory() in d:\Builds\FluentNH\src\FluentNHibernate\Cfg\FluentConfiguration.cs:93 Anyone had a similar error? I've seach the web / stackoverflow / NHibernate forums but only found people who had a problem when running in medium trust mode, not full trust. I've been developing for several months on this application on this machine with previous versions of Fluent NHibernate and NHibernate. The machine I'm running this on is 64-bit, you never know that this is relevant.

    Read the article

  • Ping "replies" from same computer with 'Destination host unreachable' (no route to other computer)

    - by Srekel
    I've got two computers in a LAN behind a wireless router. One has XP with ip 192.168.1.2 This one has W7 with ip 192.168.1.7 If I try to ping the other one from this computer, I get this: C:\Users\Srekel>ping 192.168.1.2 Pinging 192.168.1.2 with 32 bytes of data: Reply from 192.168.1.7: Destination host unreachable. Reply from 192.168.1.7: Destination host unreachable. Reply from 192.168.1.7: Destination host unreachable. Reply from 192.168.1.7: Destination host unreachable. Ping statistics for 192.168.1.2: Packets: Sent = 4, Received = 4, Lost = 0 (0% loss), Tracert gives the same result: C:\Users\Srekel>tracert 192.168.1.2 Tracing route to 192.168.1.2 over a maximum of 30 hops 1 Kakburken4 [192.168.1.7] reports: Destination host unreachable. Trace complete. Although I can ping and tracert the router without any problems. I have disabled the firewalls on both computers. The router is set to use DHCP (if that matters). Here is the output from "route". C:\Users\Srekel>route print =========================================================================== Interface List 13...00 25 86 df c6 89 ......TP-LINK Wireless N Adapter 12...e0 cb 4e 26 b9 84 ......Realtek PCIe GBE Family Controller #2 11...e0 cb 4e 26 be 94 ......Realtek PCIe GBE Family Controller 1...........................Software Loopback Interface 1 16...00 00 00 00 00 00 00 e0 Microsoft ISATAP Adapter #2 14...00 00 00 00 00 00 00 e0 Teredo Tunneling Pseudo-Interface =========================================================================== IPv4 Route Table =========================================================================== Active Routes: Network Destination Netmask Gateway Interface Metric 0.0.0.0 0.0.0.0 192.168.1.1 192.168.1.7 20 127.0.0.0 255.0.0.0 On-link 127.0.0.1 306 127.0.0.1 255.255.255.255 On-link 127.0.0.1 306 127.255.255.255 255.255.255.255 On-link 127.0.0.1 306 192.168.1.0 255.255.255.0 On-link 192.168.1.7 276 192.168.1.7 255.255.255.255 On-link 192.168.1.7 276 192.168.1.255 255.255.255.255 On-link 192.168.1.7 276 224.0.0.0 240.0.0.0 On-link 127.0.0.1 306 224.0.0.0 240.0.0.0 On-link 192.168.1.7 276 255.255.255.255 255.255.255.255 On-link 127.0.0.1 306 255.255.255.255 255.255.255.255 On-link 192.168.1.7 276 =========================================================================== Persistent Routes: None IPv6 Route Table =========================================================================== Active Routes: If Metric Network Destination Gateway 14 58 ::/0 On-link 1 306 ::1/128 On-link 14 58 2001::/32 On-link 14 306 2001:0:5ef5:73ba:881:20c1:3f57:fef8/128 On-link 14 306 fe80::/64 On-link 14 306 fe80::881:20c1:3f57:fef8/128 On-link 1 306 ff00::/8 On-link 14 306 ff00::/8 On-link =========================================================================== Persistent Routes: None I've set up and debugged a few networks in my life but I'm not really an advanced network user, so I'm not sure what might be wrong. Any ideas? Oh, and pinging this computer from the other computer doesn't work either.

    Read the article

  • ReadyNAS Duo - FTP home network connectivity issue

    - by dwabyick
    I have a ReadyNas Duo that I recently purchased and configured on my local home network. I'm an AT&T DSL subscriber using their default 2701HG-B Gateway (2Wire) wireless router. Basically, I have managed to configure my ReadyNAS, and can access HTTP shares and WINS shares just fine, but cannot get access to it via FTP. I've enabled it in the 'Standard File Protocols' section in the UI, and made a share have read/write default access via FTP. My settings: Port: 21 Authentication mode: User Allow upload resumes: Yes Passive ports: 1024-65535 Masquerade as: (empty, but I've tried the internal IP address). I've even poked around at my router, which has a firewall, and even tried to poke a hole for the 'FTP Server'app for the ReadyNAS. Doesn't seem like I should need to do this, or should. Any ideas what else to check? Thanks! -Daniel

    Read the article

  • OpenWrt logging: how to find out "wifi deauthentication"

    - by user62367
    If someone starts to use the wifi, i can see that with logread: Jan 23 21:04:47 router daemon.info hostapd: wlan0: STA XX:XX:XX:XX:XX:XX IEEE 802.11: authenticated But how can i see, that he/she's disconnecting? Theres no "bla-bla deauthenticated bla" line in logread, or even a thing that points to that someone get's disconnected.. I tried to google: http://wiki.openwrt.org/doc/uci/system But it doesn't writes about loglevel. Can anyone help me find out, how to find out that someone disconnects it's wifi from the router? The logread doesn't even writes a line when someone disconnects. Please help!! It's important! Thank you!:\

    Read the article

  • One IP, One Port, Multiple Servers

    - by Adrian Godong
    I am looking for a solution to forward one public IP address and one specific port to different machines based on hostname (as of now, I need it only for HTTP). The current setup is NAT on a commodity router (it only provide simple public port to private IP address / port forwarding). I can add a Windows Server 2008 R2 machine before the router if required, but prefer not to do so. So ideally, I would like to have the current setup and the forwarding is done on one of the Windows Servers. Is it possible to do this?

    Read the article

  • Automatically repair network connection when it goes down.

    - by Spines
    Every hour or so my wireless router goes down, and everyone connected loses internet for a couple minutes. If I right click on my network connection and choose repair, I usually get internet back quicker. Is there a way I can automatically have it try to repair the connection once it goes down? Can I write a program to do this if there isn't a built in windows setting? BTW I'm using Windows XP. EDIT:My router is a Linksys WRT110 with Firmware Version: 1.0.04, and I have cable internet. The signal is 100%. I live in an apartment complex and there are about 15 other wifi networks visible to me, not sure if that has any effect.

    Read the article

  • Maven 2 checkstyle plugin version 2.5 - Problem with configLocation

    - by Nils Schmidt
    Hi there, I am using checkstyle plugin in maven 2. I now want to switch my config file, from the default one to a) an online file, or b) a local file. I tried the following two things, which both didnt work. Any suggestions? A) Local file, which is directly in my project folder next to the pom.xml <plugin> <groupId>org.apache.maven.plugins</groupId> <artifactId>maven-checkstyle-plugin</artifactId> <configuration> <configLocation>checkstyle.xml</configLocation> </configuration> </plugin> B) Remote file, that is stored on a server <plugin> <groupId>org.apache.maven.plugins</groupId> <artifactId>maven-checkstyle-plugin</artifactId> <configuration> <configLocation>http://stud.hs-heilbronn.de/~nischmid/development/checkstyle-config.xml</configLocation> </configuration> </plugin> Both cases result in an error like this: [INFO] An error has occurred in Checkstyle report generation. Embedded error: Failed during checkstyle execution Could not find resource 'file:checkstyle.xml'. Any help would be appreciated!

    Read the article

  • Windows SBS 2003 DNS taking over network

    - by Simon
    I have Windows Small Business Server 2003 premium edition on my new server box, this hosts a webapp on IIS. It has set up a DNS Server to solve requests to the webapp. I have a linux server/router that has does DNAT and portforwards port 80 to the new box. My linux router serves as a firewall and dhcp When i plug the SBS2003 server to the network, it leaves everyone on my network without web browsing, it looks like the DNS requests are going to the new server. I configured the DNS forwarders on SBS2003 to my ISP dns but it doesnt work... Is there something i am missing?

    Read the article

  • Build a RAID-5 USB Array or NAS?

    - by TK Kocheran
    I'm looking to build a RAID-5 or RAID-6 hard disk array to be used as a centralized backup location for my home network. I have a lot of 4-8GB DVD ISO files which I intend to serve over the network to my TV using DLNA or something similar. I need decent write times, fast read times, and preferably a way to connect this array to my network router over USB. I'll probably be using ext3/4 on it (I'd use btrfs if my router supported it :-[). Is there a way to build a RAID array that is accessible over USB? I'm kind of new to this and most guides assume you're running a RAID array inside your machine. I need at least 5TB of space, and I need redundancy, so I prefer RAID-6. How can I go about accomplishing this?

    Read the article

  • Wireless Bridge with NetGear and TP-Link

    - by Tiago Cruz
    I have a wireless NetGear WGR614 v7 (little old) router connected to the internet, but I can't get a good signal in the other end of my house. I have another new one, model TP-Link TL-WR941ND wireless router. I was able to do the stuff works using a wired cable, but now, I would like to do the same using wireless connections (bridge mode, some like WDS?) Now, the computer connected to TP LINK was able to ping my computer connected to NETGEAR, but we cannot go IP ADDRESS outside my network, only internals ones. What can I do to configure this? Is needed that BOTH wireless routers support BRIDGE mode or only one its good enough? Thanks a lot!!

    Read the article

  • log4net affecting other projects which don't even use it

    - by Graeme
    I'm seeing something really strange happening with some projects I'm working on. I used log4net in an MVC web site and this was working great. I then was working on a totally unrelated Console application which uses the SharePoint API and as soon as I include the following line (other lines don't cause the problem) SPLimitedWebPartManager spWebPartManager = web.GetLimitedWebPartManager("http://blah/blah.aspx?PageView=Shared", System.Web.UI.WebControls.WebParts.PersonalizationScope.Shared); I get the following message in the console app log4net:ERROR XmlConfigurator: Failed to find configuration section 'log4net' in the application's .config file. Check your .config file for the <log4net> and < configSections> elements. The configuration section should look like: <section n ame="log4net" type="log4net.Config.Log4NetConfigurationSectionHandler,log4net" / > log4net:ERROR XmlConfigurator: Failed to find configuration section 'log4net' in the application's .config file. Check your .config file for the <log4net> and < configSections> elements. The configuration section should look like: <section n ame="log4net" type="log4net.Config.Log4NetConfigurationSectionHandler,log4net" / > I get this twice after a small delay. The delay is probably the request to get the web part manager from the page but I'm not sure why this log4net error is showing up in this project. I've gone through the code and bin folders etc. and found no trace of any log4net mentions. Any ideas why this might be happening?

    Read the article

  • DNS problems with Google on Windows 7

    - by awishformore
    Hello dear superuser community. I had no idea where to post this because it is a problem that completely baffles me. I have a lot of experience with network configuration, but I am completely out of ideas on how to fix this. I have a Fritz!Box branded router on my ISP 1&1 in Germany. My computer is connected to it with a normal Ethernet cable. I always manually set my IP on the computer and use the Google DNS servers for name resolution. I also tried OpenDNS and the result is the same. With that configuration the following happens: Google search responds with big delay Gmail, Google Calendar & Google Drive requests time out the majority of the time In order to troubleshoot, I set the network connection to DHCP for both IP & DNS. At that point, what happens is the following: Google search times out most of the time Gmail, Google Calendar & Google Drive work most of the time Sometimes, it happens that the sites that time out will come up, but weirdly enough, the pictures on the buttons will be missing. For instance, the magnifying glass on Google will be gone or the circle arrow on Gmail (but all buttons of course). All other websites load just fine - and very quickly. All other network functionality is completely unimpacted. The behaviour of fixed IP & Google DNS vs automatic IP & DNS is easily reproducible. I am going crazy trying to fix this as I have no idea what the hell is going on at this point. Here a list of the things I have tried thus far: Flushed the DNS Tried on different browsers (Works fine on my laptop by the way) Tried disabling Teredo & IPv6 stack Emptied all caches Checked the HOSTS file Rebooted the router Reset the router Reinstalled the network adapter Tracert displayes normal route until timing out at one point Ping usually doesn't work for the unreachable sites either Ran both complete Norton 360 & Kaspersky 2012 scan Ran Kaspersky Virus Removal Tool in safe mode Tried connection in safe mode & networking enabled If you have any ideas, please let me know. I'm getting desperate...

    Read the article

  • Windows 7 can't connect via ethernet to Airport Extreme

    - by Mr AJL
    I have an Airport Extreme router, and everything works beautifully on the Mac, but my Windows 7 computer, which is connected via a regular ethernet cable, can't see any network. The Windows computer says there's no cable connected. Any ideas? Is there some kind of setting you have to enable with the Airport utility? I looked everywhere but can't find anything. Or do I need to install that Airport utility something on the PC just to connect to the router? (Haven't tried because the PC has no CD drive)

    Read the article

< Previous Page | 198 199 200 201 202 203 204 205 206 207 208 209  | Next Page >