Search Results

Search found 5295 results on 212 pages for 'interval tree'.

Page 203/212 | < Previous Page | 199 200 201 202 203 204 205 206 207 208 209 210  | Next Page >

• Cisco ASA: How to route PPPoE-assigned subnet?

  - by Martijn Heemels

  We've just received a fiber uplink, and I'm trying to configure our Cisco ASA 5505 to properly use it. The provider requires us to connect via PPPoE, and I managed to configure the ASA as a PPPoE client and establish a connection. The ASA is assigned an IP address by PPPoE, and I can ping out from the ASA to the internet, but I should have access to an entire /28 subnet. I can't figure out how to get that subnet configured on the ASA, so that I can route or NAT the available public addresses to various internal hosts. My assigned range is: 188.xx.xx.176/28 The address I get via PPPoE is 188.xx.xx.177/32, which according to our provider is our Default Gateway address. They claim the subnet is correctly routed to us on their side. How does the ASA know which range it is responsible for on the Fiber interface? How do I use the addresses from my range? To clarify my config; The ASA is currently configured to default-route to our ADSL uplink on port Ethernet0/0 (interface vlan2, nicknamed Outside). The fiber is connected to port Ethernet0/2 (interface vlan50, nicknamed Fiber) so I can configure and test it before making it the default route. Once I'm clear on how to set it all up, I'll fully replace the Outside interface with Fiber. My config (rather long): : Saved : ASA Version 8.3(2)4 ! hostname gw domain-name example.com enable password ****** encrypted passwd ****** encrypted names name 10.10.1.0 Inside-dhcp-network description Desktops and clients that receive their IP via DHCP name 10.10.0.208 svn.example.com description Subversion server name 10.10.0.205 marvin.example.com description LAMP development server name 10.10.0.206 dns.example.com description DNS, DHCP, NTP ! interface Vlan2 description Old ADSL WAN connection nameif outside security-level 0 ip address 192.168.1.2 255.255.255.252 ! interface Vlan10 description LAN vlan 10 Regular LAN traffic nameif inside security-level 100 ip address 10.10.0.254 255.255.0.0 ! interface Vlan11 description LAN vlan 11 Lab/test traffic nameif lab security-level 90 ip address 10.11.0.254 255.255.0.0 ! interface Vlan20 description LAN vlan 20 ISCSI traffic nameif iscsi security-level 100 ip address 10.20.0.254 255.255.0.0 ! interface Vlan30 description LAN vlan 30 DMZ traffic nameif dmz security-level 50 ip address 10.30.0.254 255.255.0.0 ! interface Vlan40 description LAN vlan 40 Guests access to the internet nameif guests security-level 50 ip address 10.40.0.254 255.255.0.0 ! interface Vlan50 description New WAN Corporate Internet over fiber nameif fiber security-level 0 pppoe client vpdn group KPN ip address pppoe ! interface Ethernet0/0 switchport access vlan 2 speed 100 duplex full ! interface Ethernet0/1 switchport trunk allowed vlan 10,11,30,40 switchport trunk native vlan 10 switchport mode trunk ! interface Ethernet0/2 switchport access vlan 50 speed 100 duplex full ! interface Ethernet0/3 shutdown ! interface Ethernet0/4 shutdown ! interface Ethernet0/5 switchport access vlan 20 ! interface Ethernet0/6 shutdown ! interface Ethernet0/7 shutdown ! boot system disk0:/asa832-4-k8.bin ftp mode passive clock timezone CEST 1 clock summer-time CEDT recurring last Sun Mar 2:00 last Sun Oct 3:00 dns domain-lookup inside dns server-group DefaultDNS name-server dns.example.com domain-name example.com same-security-traffic permit inter-interface same-security-traffic permit intra-interface object network inside-net subnet 10.10.0.0 255.255.0.0 object network svn.example.com host 10.10.0.208 object network marvin.example.com host 10.10.0.205 object network lab-net subnet 10.11.0.0 255.255.0.0 object network dmz-net subnet 10.30.0.0 255.255.0.0 object network guests-net subnet 10.40.0.0 255.255.0.0 object network dhcp-subnet subnet 10.10.1.0 255.255.255.0 description DHCP assigned addresses on Vlan 10 object network Inside-vpnpool description Pool of assignable addresses for VPN clients object network vpn-subnet subnet 10.10.3.0 255.255.255.0 description Address pool assignable to VPN clients object network dns.example.com host 10.10.0.206 description DNS, DHCP, NTP object-group service iscsi tcp description iscsi storage traffic port-object eq 3260 access-list outside_access_in remark Allow access from outside to HTTP on svn. access-list outside_access_in extended permit tcp any object svn.example.com eq www access-list Insiders!_splitTunnelAcl standard permit 10.10.0.0 255.255.0.0 access-list iscsi_access_in remark Prevent disruption of iscsi traffic from outside the iscsi vlan. access-list iscsi_access_in extended deny tcp any interface iscsi object-group iscsi log warnings ! snmp-map DenyV1 deny version 1 ! pager lines 24 logging enable logging timestamp logging asdm-buffer-size 512 logging monitor warnings logging buffered warnings logging history critical logging asdm errors logging flash-bufferwrap logging flash-minimum-free 4000 logging flash-maximum-allocation 2000 mtu outside 1500 mtu inside 1500 mtu lab 1500 mtu iscsi 9000 mtu dmz 1500 mtu guests 1500 mtu fiber 1492 ip local pool DHCP_VPN 10.10.3.1-10.10.3.20 mask 255.255.0.0 ip verify reverse-path interface outside no failover icmp unreachable rate-limit 10 burst-size 5 asdm image disk0:/asdm-635.bin asdm history enable arp timeout 14400 nat (inside,outside) source static any any destination static vpn-subnet vpn-subnet ! object network inside-net nat (inside,outside) dynamic interface object network svn.example.com nat (inside,outside) static interface service tcp www www object network lab-net nat (lab,outside) dynamic interface object network dmz-net nat (dmz,outside) dynamic interface object network guests-net nat (guests,outside) dynamic interface access-group outside_access_in in interface outside access-group iscsi_access_in in interface iscsi route outside 0.0.0.0 0.0.0.0 192.168.1.1 1 timeout xlate 3:00:00 timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02 timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00 timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00 timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute timeout tcp-proxy-reassembly 0:01:00 dynamic-access-policy-record DfltAccessPolicy aaa-server SBS2003 protocol radius aaa-server SBS2003 (inside) host 10.10.0.204 timeout 5 key ***** aaa authentication enable console SBS2003 LOCAL aaa authentication ssh console SBS2003 LOCAL aaa authentication telnet console SBS2003 LOCAL http server enable http 10.10.0.0 255.255.0.0 inside snmp-server host inside 10.10.0.207 community ***** version 2c snmp-server location Server room snmp-server contact [email protected] snmp-server community ***** snmp-server enable traps snmp authentication linkup linkdown coldstart snmp-server enable traps syslog crypto ipsec transform-set TRANS_ESP_AES-256_SHA esp-aes-256 esp-sha-hmac crypto ipsec transform-set TRANS_ESP_AES-256_SHA mode transport crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac crypto ipsec transform-set ESP-DES-SHA esp-des esp-sha-hmac crypto ipsec transform-set ESP-DES-MD5 esp-des esp-md5-hmac crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac crypto ipsec transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac crypto ipsec transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac crypto ipsec transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac crypto ipsec transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac crypto ipsec security-association lifetime seconds 28800 crypto ipsec security-association lifetime kilobytes 4608000 crypto dynamic-map outside_dyn_map 20 set pfs group5 crypto dynamic-map outside_dyn_map 20 set transform-set TRANS_ESP_AES-256_SHA crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5 crypto map outside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP crypto map outside_map interface outside crypto isakmp enable outside crypto isakmp policy 1 authentication pre-share encryption 3des hash sha group 2 lifetime 86400 telnet 10.10.0.0 255.255.0.0 inside telnet timeout 5 ssh scopy enable ssh 10.10.0.0 255.255.0.0 inside ssh timeout 5 ssh version 2 console timeout 30 management-access inside vpdn group KPN request dialout pppoe vpdn group KPN localname INSIDERS vpdn group KPN ppp authentication pap vpdn username INSIDERS password ***** store-local dhcpd address 10.40.1.0-10.40.1.100 guests dhcpd dns 8.8.8.8 8.8.4.4 interface guests dhcpd update dns interface guests dhcpd enable guests ! threat-detection basic-threat threat-detection scanning-threat threat-detection statistics host number-of-rate 2 threat-detection statistics port number-of-rate 3 threat-detection statistics protocol number-of-rate 3 threat-detection statistics access-list threat-detection statistics tcp-intercept rate-interval 30 burst-rate 400 average-rate 200 ntp server dns.example.com source inside prefer webvpn group-policy DfltGrpPolicy attributes vpn-tunnel-protocol IPSec l2tp-ipsec group-policy Insiders! internal group-policy Insiders! attributes wins-server value 10.10.0.205 dns-server value 10.10.0.206 vpn-tunnel-protocol IPSec l2tp-ipsec split-tunnel-policy tunnelspecified split-tunnel-network-list value Insiders!_splitTunnelAcl default-domain value example.com username martijn password ****** encrypted privilege 15 username marcel password ****** encrypted privilege 15 tunnel-group DefaultRAGroup ipsec-attributes pre-shared-key ***** tunnel-group Insiders! type remote-access tunnel-group Insiders! general-attributes address-pool DHCP_VPN authentication-server-group SBS2003 LOCAL default-group-policy Insiders! tunnel-group Insiders! ipsec-attributes pre-shared-key ***** ! class-map global-class match default-inspection-traffic class-map type inspect http match-all asdm_medium_security_methods match not request method head match not request method post match not request method get ! ! policy-map type inspect dns preset_dns_map parameters message-length maximum 512 policy-map type inspect http http_inspection_policy parameters protocol-violation action drop-connection policy-map global-policy class global-class inspect dns inspect esmtp inspect ftp inspect h323 h225 inspect h323 ras inspect http inspect icmp inspect icmp error inspect mgcp inspect netbios inspect pptp inspect rtsp inspect snmp DenyV1 ! service-policy global-policy global smtp-server 123.123.123.123 prompt hostname context call-home profile CiscoTAC-1 no active destination address http https://tools.cisco.com/its/service/oddce/services/DDCEService destination address email [email protected] destination transport-method http subscribe-to-alert-group diagnostic subscribe-to-alert-group environment subscribe-to-alert-group inventory periodic monthly subscribe-to-alert-group configuration periodic monthly subscribe-to-alert-group telemetry periodic daily hpm topN enable Cryptochecksum:a76bbcf8b19019771c6d3eeecb95c1ca : end asdm image disk0:/asdm-635.bin asdm location svn.example.com 255.255.255.255 inside asdm location marvin.example.com 255.255.255.255 inside asdm location dns.example.com 255.255.255.255 inside asdm history enable

  Read the article

• Unicast traffic between hosts on a switch leaving the switch by its uplink. Why?

  - by Rich Lafferty

  I have a weird thing happening on our network at my office which I can't quite get my head around. In particular I can't tell if it's a problem with a switch, or a problem with configuration. We have a Cisco SG300-52 switch (sw01) in the top of a rack in our server room, connected to another SG300-28 that acts as our core switch (core01). Both run layer 2 only, our firewalls do routing between VLANs. They have a dozen or so VLANs between them. Gi1 on sw01 is a trunk port connected to gi1 on core01. (Disclosure: There are other switches in our environment but I'm pretty sure I've isolated the problem down to these two. Happy to provide more info if necessary.) The behaviour I'm seeing is limited to one VLAN, vlan 12 -- or, at least, it's not happening on the other ones I checked (It's hard to guarantee the absence of packets), and it is: sw01 is forwarding, to core01, traffic which is between two hosts which are both plugged into sw01. (I noticed this because the IDS in our firewall gave a false positive on traffic which should not reach the firewall.) We noticed this mostly between our two dhcp/dns servers, net01 (10.12.0.10) and net02 (10.12.0.11). net01 is physical hardware and net02 is on a VMware ESX server. net01 is connected to gi44 on sw01 and net02's ESX server to gi11. [net01]----gi44-[sw01]-gi1----gi1-[core01] [net02]----gi11/ Let's see some interfaces! Remember, vlan 12 is the problem vlan. Of the others I explicitly verified that vlan 27 was not affected. Here's the two hosts' ports: esx01 contains net02. sw01#sh run int gi11 interface gigabitethernet11 description esx01 lldp med disable switchport trunk allowed vlan add 5-7,11-13,100 switchport trunk native vlan 27 ! sw01#sh run int gi44 interface gigabitethernet44 description net01-1 lldp med disable switchport mode access switchport access vlan 12 ! Here's the trunk on sw01. sw01#sh run int gi1 interface gigabitethernet1 description "trunk to core01" lldp med disable switchport trunk allowed vlan add 4-7,11-13,27,100 ! And the other end of the trunk on core01. interface gigabitethernet1 description sw01 macro description switch switchport trunk allowed vlan add 2-7,11-16,27,100 ! I have a monitor port on core01, thus: core01#sh run int gi12 interface gigabitethernet12 description "monitor port" port monitor GigabitEthernet 1 ! And the monitor port on core01 sees unicast traffic going between net01 and net02, both of which are on sw01! I've verified this with a monitor port on sw01 that sees the net01-net02 unicast traffic leaving via gi1 too. sw01 knows that both of those hosts are on ports that are not its trunk port: :) ratchet$ arp -a | grep net net02.2ndsiteinc.com (10.12.0.11) at 00:0C:29:1A:66:15 [ether] on eth0 net01.2ndsiteinc.com (10.12.0.10) at 00:11:43:D8:9F:94 [ether] on eth0 sw01#sh mac addr addr 00:0C:29:1A:66:15 Aging time is 300 sec Vlan Mac Address Port Type -------- --------------------- ---------- ---------- 12 00:0c:29:1a:66:15 gi11 dynamic sw01#sh mac addr addr 00:11:43:D8:9F:94 Aging time is 300 sec Vlan Mac Address Port Type -------- --------------------- ---------- ---------- 12 00:11:43:d8:9f:94 gi44 dynamic I also brought up an unused port on sw01 on vlan 12, but the unicast traffic was (as best as I could tell) not coming out that port. So it doesn't look like sw01 is pushing it out all its ports, just the right ports and also gi1! I've verified that sw01 is not filling up its address-table: sw01#sh mac addr count This may take some time. Capacity : 8192 Free : 7983 Used : 208 The full configs for both core01 and sw01 are available: core01, sw01. Finally, versions: sw01#sh ver SW version 1.1.2.0 ( date 12-Nov-2011 time 23:34:26 ) Boot version 1.0.0.4 ( date 08-Apr-2010 time 16:37:57 ) HW version V01 core01#sh ver SW version 1.1.2.0 ( date 12-Nov-2011 time 23:34:26 ) Boot version 1.1.0.6 ( date 11-May-2011 time 18:31:00 ) HW version V01 So my understanding is this: sw01 should take unicast traffic for net01 and send it only out net02's port, and vice versa; none of it should go out sw01's uplink. But core01, receiving traffic on gi1 for a host it knows is on gi1, is right in sending it out all of its ports. (That is: sw01 is misbehaving, but core01 is doing what it should given the circumstances.) My question is: Why is sw01 sending that unicast traffic out its uplink, gi1? (And pre-emptively: yes, I know SG300s leave much to be desired, and yes, we should have spanning-tree enabled, but that's where I'm at right now.)

  Read the article

• SVN: Release branch headaches, how to merge in website revisions as and when cleared to go live?

  - by Pete Duncanson

  I need a sanity check here if we can, any ideas on correcting/changing the following are very welcome! We've been getting ourselves in knots of late with our SVN and are trying to correct it by putting a Trunk/Release system in place. We have a large website that we develop on and we store it all in SVN. Heres what we had in mind: We have trunk and a release branch All work gets checked into Trunk. When a feature is deemed ready for the next release it is merged into a Release branch. We only have one release branch and just tag "Latest" when we do a push to live We hope to be able to get all the files changed from Latest to Head to give us a zip that we can upload (any ideas on an easy way to do this via scripting?) So we set all this up and where very happy with ourselves. Except its not working and heres why. We work on lots a different features/fixes/problems at once and they don't all get nicely checked in feature complete (but always working at least). Then sometimes you have to wait for Clients to sign off. As a result you end up with revisions which are "ready for live" being scattered with ones which are "still being worked on" in trunk. That means that the completed revisions are not getting merged in sequentially but out of order. I thought SVN could handle this, clever little thing it is, but apparently not. Heres an example: Pete changes some CSS to make a new button look pretty (Revision 1) Dave add some CSS to the bottom of the same CSS file as Pete's for a new feature (Revision 2) Dave's mod gets the nod so he merges it into Release and commits it with a log message mentioning revision number and bug tracking id. Pete adds more buttons to finish this mod, no CSS changes here though (Revision 3) Pete then merges his mods (Revision 1 and 3) into the Head of Release (which has Daves merge in it) but this over-writes Daves CSS additions which now dissapear completely. This leads to the site being broken and the Release branch being pretty much useless. So we tried some other ideas like reverting Release back to "Latest" and then just merging in all the Revisions 1,2 and 3 in order. This worked fine until we had Revision 4 which was not ready for live and Revision 5 which was. Suddenly we are getting ourselves in knots again with exactly the same problem! Ok so take three. Revert to Latest, merge in Revision 5, then do any update back to Head. Tree conflicts galore! So thats a no no. I cracked in the end and built it all up manaually but its not something I want to do regular, ideally I want to script our deployment but can't while Release is in such a mess. HELP! What the heck are we doing wrong? I can't seem to find any solutions to this problem of wanting different none sequential Revisions in Release. If its not possible thats fine but how the heck are we meant to get stuff live easily. We can't branch for every single change, the site takes 30 minutes+ to check out it would take too long. Side note, we are using TortoiseSVN so can we keep command line examples to a minimum in any answers? Latest version of TSVN and SVN Version 1.6 so we have the funky merge tracking etc. EDIT: An excellent blog post which deals with the dev/release cycle (although using GIT but still relivant) thought everyone would like to read it if they found this question interesting. (http://nvie.com/git-model) EDIT 2: I wrote a blog post on how to show which branch you are working on in your website which others have asked me about (http://www.offroadcode.com/2010/5/14/which-svn-branch-are-you-working-on.aspx). Hope that helps. In the meantime we are looking at Kiln and hoping to make the switch next month (gulp!)

  Read the article

• WPF: Focus in a Window and UserControl

  - by Echilon

  I'm trying to get a UserControl to tab properly and am baffled. The logical tree looks like this. |-Window -Grid -TabControl -TabItem -StackPanel -MyUserControl |-StackPanel -GroupBox -Grid -ComboBox -Textbox1 -Textbox2 Everything works fine, except when the visibility converter for the ComboBox returns Visibility.Collapsed (don't allow user to change database mode), then when textbox1 is selected, instead of being able to tab through the controls in the UserControl, the focus shifts to a button declared at the bottom of the window. Nothing else apart from the controls displayed has TabIndex or FocusManager properties set. I'm banging my head against a brick wall and I must be missing something. I've tried IsFocusScope=True/False, played with FocusedElement and nothing works if that ComboBox is invisible (Visibility.Collapsed). <Window x:Class="MyNamespace.Client.WinInstaller" xmlns="http://schemas.microsoft.com/winfx/2006/xaml/presentation" xmlns:x="http://schemas.microsoft.com/winfx/2006/xaml" FocusManager.FocusedElement="{Binding ElementName=tabWizard}"> <Window.Resources> <props:Settings x:Key="settings" /> </Window.Resources> <Grid Grid.IsSharedSizeScope="True"> <!-- row and column definitions omitted --> <loc:SmallHeader Grid.Row="0" x:Name="headerBranding" HeaderText="Setup" /> <TabControl x:Name="tabWizard" DataContext="{StaticResource settings}" SelectedIndex="0" FocusManager.IsFocusScope="True"> <TabItem x:Name="tbStart" Height="0"> <StackPanel> <TextBlock Text="Database Mode"/> <loc:DatabaseSelector x:Name="dbSelector" AllowChangeMode="False" TabIndex="1" AvailableDatabaseModes="SQLServer" IsPortRequired="False" DatabaseMode="{Binding Default.DbMode,Mode=TwoWay,UpdateSourceTrigger=PropertyChanged}" DatabasePath="{Binding Default.DatabasePath,Mode=TwoWay,UpdateSourceTrigger=PropertyChanged}"/> </StackPanel> </TabItem> ... The top of the user control is below: <UserControl x:Class="MyNamespace.Client.DatabaseSelector" xmlns="http://schemas.microsoft.com/winfx/2006/xaml/presentation" xmlns:x="http://schemas.microsoft.com/winfx/2006/xaml" x:Name="root" FocusManager.IsFocusScope="True" FocusManager.FocusedElement="{Binding ElementName=cboDbMode}"> <UserControl.Resources> <conv:DatabaseModeIsFileBased x:Key="DatabaseModeIsFileBased"/> <BooleanToVisibilityConverter x:Key="BooleanToVisibilityConverter"/> </UserControl.Resources> <StackPanel DataContext="{Binding}"> <GroupBox> <Grid> <!-- row and column definitions omitted --> <Label Content="Database Mode"/> <ComboBox x:Name="cboDbMode" SelectedValue="{Binding ElementName=root,Path=DatabaseMode,Mode=TwoWay,UpdateSourceTrigger=PropertyChanged}" DisplayMemberPath="Value" SelectedValuePath="Key" TabIndex="1" Visibility="{Binding AllowChangeMode,ElementName=root,Converter={StaticResource BooleanToVisibilityConverter}}" /> <!-- AllowChangeMode is a DependencyProperty on the UserControl --> <Grid><!-- row and column definitions omitted --> <Label "Host"/> <TextBox x:Name="txtDBHost" Text="{Binding ElementName=root,Path=DatabaseHost,Mode=TwoWay,UpdateSourceTrigger=PropertyChanged}" TabIndex="2" /> <TextBox x:Name="txtDBPort" Text="{Binding ElementName=root,Path=DatabasePortString,Mode=TwoWay,UpdateSourceTrigger=PropertyChanged}" TabIndex="3" />

  Read the article

• Weird XPath behavior in libxml2

  - by Josh K

  I have this XML tree that looks like this (I've changed the tag names but if you're really clever you may figure out what I'm actually doing.) <ListOfThings> <Thing foo:action="add"> <Bar>doStuff --slowly</Bar> <Index>1</Index> </Thing> <Thing foo:action="add"> <Bar>ping yourMother.net</Bar> <Index>2</Index> </Thing> </ListOfThings> With libxml2, I want to programmatically insert a new Thing tag into the ListOfThings with the Index being the highest current index, plus one. I do it like this (sanity checking removed for brevity): xpath = "//urn:myformat[@foo='bar']/" "urn:mysection[@name='baz']/" "urn:ListOfThings/urn:Thing/urn:Index"; xpathObj = xmlXPathEvalExpression(xpath, xpathCtx); nodes = xpathObj->nodesetval; /* Find last value and snarf the value of the tag */ highest = atoi(nodes->nodeTab[nodes->nodeNr - 1]->children->content); snprintf(order, sizeof(order), "%d", highest + 1); /* highest index plus one */ /* now move up two levels.. */ cmdRoot = nodes->nodeTab[nodes->nodeNr - 1]; ASSERT(cmdRoot->parent && cmdRoot->parent->parent); cmdRoot = cmdRoot->parent->parent; /* build the child tag */ newTag = xmlNewNode(NULL, "Thing"); xmlSetProp(newTag, "foo:action", "add"); /* set new node values */ xmlNewTextChild(newTag, NULL, "Bar", command); xmlNewChild(newTag, NULL, "Index", order); /* append this to cmdRoot */ xmlAddChild(cmdRoot, newTag); But if I call this function twice (to add two Things), the XPath expression doesn't catch the new entry I made. Is there a function I need to call to kick XPath in the shins and get it to make sure it really looks over the whole xmlDocPtr again? It clearly does get added to the document, because when I save it, I get the new tags I added. To be clear, the output looks like this: <ListOfThings> <Thing foo:action="add"> <Bar>doStuff --slowly</Bar> <Index>1</Index> </Thing> <Thing foo:action="add"> <Bar>ping yourMother.net</Bar> <Index>2</Index> </Thing> <Thing foo:action="add"> <Bar>newCommand1</Bar> <Index>3</Index> </Thing> <Thing foo:action="add"> <Bar>newCommand2</Bar> <Index>3</Index> <!-- this is WRONG! --> </Thing> </ListOfThings> I used a debugger to check what happened after xmlXPathEvalExpression got called and I saw that nodes->nodeNr was the same each time. Help me, lazyweb, you're my only hope!

  Read the article

• C#: Inheritence, Overriding, and Hiding

  - by Rosarch

  I'm having difficulty with an architectural decision for my C# XNA game. The basic entity in the world, such as a tree, zombie, or the player, is represented as a GameObject. Each GameObject is composed of at least a GameObjectController, GameObjectModel, and GameObjectView. These three are enough for simple entities, like inanimate trees or rocks. However, as I try to keep the functionality as factored out as possible, the inheritance begins to feel unwieldy. Syntactically, I'm not even sure how best to accomplish my goals. Here is the GameObjectController: public class GameObjectController { protected GameObjectModel model; protected GameObjectView view; public GameObjectController(GameObjectManager gameObjectManager) { this.gameObjectManager = gameObjectManager; model = new GameObjectModel(this); view = new GameObjectView(this); } public GameObjectManager GameObjectManager { get { return gameObjectManager; } } public virtual GameObjectView View { get { return view; } } public virtual GameObjectModel Model { get { return model; } } public virtual void Update(long tick) { } } I want to specify that each subclass of GameObjectController will have accessible at least a GameObjectView and GameObjectModel. If subclasses are fine using those classes, but perhaps are overriding for a more sophisticated Update() method, I don't want them to have to duplicate the code to produce those dependencies. So, the GameObjectController constructor sets those objects up. However, some objects do want to override the model and view. This is where the trouble comes in. Some objects need to fight, so they are CombatantGameObjects: public class CombatantGameObject : GameObjectController { protected new readonly CombatantGameModel model; public new virtual CombatantGameModel Model { get { return model; } } protected readonly CombatEngine combatEngine; public CombatantGameObject(GameObjectManager gameObjectManager, CombatEngine combatEngine) : base(gameObjectManager) { model = new CombatantGameModel(this); this.combatEngine = combatEngine; } public override void Update(long tick) { if (model.Health <= 0) { gameObjectManager.RemoveFromWorld(this); } base.Update(tick); } } Still pretty simple. Is my use of new to hide instance variables correct? Note that I'm assigning CombatantObjectController.model here, even though GameObjectController.Model was already set. And, combatants don't need any special view functionality, so they leave GameObjectController.View alone. Then I get down to the PlayerController, at which a bug is found. public class PlayerController : CombatantGameObject { private readonly IInputReader inputReader; private new readonly PlayerModel model; public new PlayerModel Model { get { return model; } } private float lastInventoryIndexAt; private float lastThrowAt; public PlayerController(GameObjectManager gameObjectManager, IInputReader inputReader, CombatEngine combatEngine) : base(gameObjectManager, combatEngine) { this.inputReader = inputReader; model = new PlayerModel(this); Model.Health = Constants.PLAYER_HEALTH; } public override void Update(long tick) { if (Model.Health <= 0) { gameObjectManager.RemoveFromWorld(this); for (int i = 0; i < 10; i++) { Debug.WriteLine("YOU DEAD SON!!!"); } return; } UpdateFromInput(tick); // .... } } The first time that this line is executed, I get a null reference exception: model.Body.ApplyImpulse(movementImpulse, model.Position); model.Position looks at model.Body, which is null. This is a function that initializes GameObjects before they are deployed into the world: public void Initialize(GameObjectController controller, IDictionary<string, string> data, WorldState worldState) { controller.View.read(data); controller.View.createSpriteAnimations(data, _assets); controller.Model.read(data); SetUpPhysics(controller, worldState, controller.Model.BoundingCircleRadius, Single.Parse(data["x"]), Single.Parse(data["y"]), bool.Parse(data["isBullet"])); } Every object is passed as a GameObjectController. Does that mean that if the object is really a PlayerController, controller.Model will refer to the base's GameObjectModel and not the PlayerController's overriden PlayerObjectModel?

  Read the article

• HELP!! Rake aborted! Can't modify frozen hash

  - by pmneve

  Too bad even the trace doesn't say which hash is involved. Sorry this post is long: am trying to provide enough context to be meaningful. Occurs intermittently when rake jobs:work is pulling a command out of delayed_jobs while my status observer is in the process of parsing a log file for detailed results of the previous delayed_job denizen. I have an observer class (in RAILS_ROOT/lib ) which listens for the events, makes a copy of them and calls the owner class ( in apps/models ) which then calls on the log parser (also in /lib) to do the actual work. (Should both of those classes, the observer and the parser be in app/models?) Am due to deliver this application in a few days and this is killing it (and me). Am using DirectoryWatcher to look for flag files that indicate the start and finish of the delayed_jobs. That is started at the end of environment.rb like this: require 'directory_watcher' $scriptStatusObserver = ScriptStatusObserver.new dirToWatch ="#{RAILS_ROOT}/tmp/flags" $directoryWatcher = DirectoryWatcher.new( dirToWatch ) $directoryWatcher.glob= "*.flg" $directoryWatcher.interval=(15) $directoryWatcher.add_observer( $scriptStatusObserver ) $directoryWatcher.persist=("#{RAILS_ROOT}/tmp/flags/dw_state.yml") $directoryWatcher.start at_exit { $directoryWatcher.stop } This code is outside of the run method (btw is that the best place or is inside the run better?) Here is the observer: require 'script_run' class ScriptStatusObserver def initialize @rcvdEvents = [] end def update( *events ) begin puts "#{LINE.to_s}: ScriptStatusObserver events: \n"+events.to_yaml cnt = 0 events.each do |e| if e.to_s.match(/^\s*added/) cnt = cnt + 1 @rcvdEvents << e end end ScriptRun.new.catch_up( @rcvdEvents ) if cnt > 0 @rcvdEvents.clear rescue puts $! end end end Here is ScriptRun (it attaches to an associative table built with has_many:through) require 'observer' class ScriptRun < ActiveRecord::Base set_table_name "scripts_runs" belongs_to :script belongs_to :run def parse( result ) parser = LogParser.new parser.parse(result) end def catch_up( events ) events.each do |e| typ = e.type path = e.path thisMatch = path.match(/flags\/(\d+)_(\d+)_([\d\.]+)_(\w+)\.flg/) run_id = thisMatch[1] script_id = thisMatch[2] ts = thisMatch[3] status = thisMatch[4] if e.to_s.match(/^\s*added/) status_update( script_id, run_id, status, ts, path ) end end end def status_update( script_id, run_id, status, ts, path ) scriptrun = ScriptRun.find(:first, :conditions => [ "run_id = ? and script_id = ?", run_id.to_i, script_id.to_i ]) if scriptrun.kind_of?(ScriptRun) currStatus = scriptrun.status if not currStatus == 'completed' scriptrun.update_attribute(:status, status) if status == 'parse' flag = File.new(path) logSpec = flag.gets flag.close logName = File.basename(logSpec) logPath = logSpec.sub(logName, '') logName =~ /^(([\w_]+)_([\w]+)_(\d+))\.log$/ name = $1 basename = $2 runenv = $3 tsOrPid = $4 result = Result.new result.log_path = logPath result.basename = basename result.name = name result.script_id = script_id.to_i result.run_id = run_id.to_i if runenv == 'sit' runenv = 'SIT3348' end result.application_environment_id = ApplicationEnvironment.find(:first, :conditions => [ "nodename = ?", runenv]).id parse(result) if run_completed?( run_id ) myRun = Run.find(run_id.to_i) if myRun.kind_of?( Run ) myRun.update_attribute( :completed, Time.now.to_f ) end end end end else puts "#{__LINE__.to_s}: ScriptRun.status_update: ScriptRun not found for run #{run_id} script #{script_id} ts #{ts.to_s}" end File.delete(path) end def run_completed?( id ) scriptruns = ScriptRun.find(:all, :conditions = [ "run_id = ?", id.to_i] ) scriptruns.each do |sr| if not sr.status == 'completed' return false end end return true end end LogParser is too long even for this post but it reads the script log and pulls detailed information (counts and timings) out of the log and writes to a details table. It also tallies and calculates averages and rolls those up into summary tables for quicker access from the web pages. Here is the error trace: (don't ask why everything is under my Windows profile. It's a long story) Scanner running 1270239731.43 directory_watcher.notify_observers: #, #] update:[#, /pneve/workspace/waftt-0.29/tmp/flags/100039_18_1270239550.108_parse.flg"] rake aborted! can't modify frozen hash C:/Documents and Settings/pneve/workspace/waftt-0.29/vendor/rails/activerecord/l ib/active_record/attribute_methods.rb:313:in []=' C:/Documents and Settings/pneve/workspace/waftt-0.29/vendor/rails/activerecord/l ib/active_record/attribute_methods.rb:313:inwrite_attribute_without_dirty' C:/Documents and Settings/pneve/workspace/waftt-0.29/vendor/rails/activerecord/l ib/active_record/dirty.rb:139:in write_attribute' C:/Documents and Settings/pneve/workspace/waftt-0.29/vendor/rails/activerecord/l ib/active_record/attribute_methods.rb:211:inlast_error=' C:/Documents and Settings/pneve/workspace/waftt-0.29/vendor/plugins/delayed_job/ lib/delayed/worker.rb:141:in handle_failed_job' C:/Documents and Settings/pneve/workspace/waftt-0.29/vendor/plugins/delayed_job/ lib/delayed/worker.rb:115:inrun' C:/Documents and Settings/pneve/workspace/waftt-0.29/vendor/plugins/delayed_job/ lib/delayed/worker.rb:162:in reserve_and_run_one_job' C:/Documents and Settings/pneve/workspace/waftt-0.29/vendor/plugins/delayed_job/ lib/delayed/worker.rb:92:inwork_off' C:/Documents and Settings/pneve/workspace/waftt-0.29/vendor/plugins/delayed_job/ lib/delayed/worker.rb:91:in times' C:/Documents and Settings/pneve/workspace/waftt-0.29/vendor/plugins/delayed_job/ lib/delayed/worker.rb:91:inwork_off' C:/Documents and Settings/pneve/workspace/waftt-0.29/vendor/plugins/delayed_job/ lib/delayed/worker.rb:66:in start' C:/Documents and Settings/pneve/workspace/waftt-0.29/vendor/rails/activesupport/ lib/active_support/core_ext/benchmark.rb:10:inrealtime' C:/Documents and Settings/pneve/workspace/waftt-0.29/vendor/plugins/delayed_job/ lib/delayed/worker.rb:65:in start' C:/Documents and Settings/pneve/workspace/waftt-0.29/vendor/plugins/delayed_job/ lib/delayed/worker.rb:62:inloop' C:/Documents and Settings/pneve/workspace/waftt-0.29/vendor/plugins/delayed_job/ lib/delayed/worker.rb:62:in start' C:/Documents and Settings/pneve/workspace/waftt-0.29/vendor/plugins/delayed_job/ lib/delayed/tasks.rb:13 c:/Documents and Settings/pneve/ruby/lib/ruby/gems/1.8/gems/rake-0.8.7/lib/rake. rb:636:incall' c:/Documents and Settings/pneve/ruby/lib/ruby/gems/1.8/gems/rake-0.8.7/lib/rake. rb:636:in execute' c:/Documents and Settings/pneve/ruby/lib/ruby/gems/1.8/gems/rake-0.8.7/lib/rake. rb:631:ineach' c:/Documents and Settings/pneve/ruby/lib/ruby/gems/1.8/gems/rake-0.8.7/lib/rake. rb:631:in execute' c:/Documents and Settings/pneve/ruby/lib/ruby/gems/1.8/gems/rake-0.8.7/lib/rake. rb:597:ininvoke_with_call_chain' c:/Documents and Settings/pneve/ruby/lib/ruby/1.8/monitor.rb:242:in synchronize ' c:/Documents and Settings/pneve/ruby/lib/ruby/gems/1.8/gems/rake-0.8.7/lib/rake. rb:590:ininvoke_with_call_chain' c:/Documents and Settings/pneve/ruby/lib/ruby/gems/1.8/gems/rake-0.8.7/lib/rake. rb:583:in invoke' c:/Documents and Settings/pneve/ruby/lib/ruby/gems/1.8/gems/rake-0.8.7/lib/rake. rb:2051:ininvoke_task' c:/Documents and Settings/pneve/ruby/lib/ruby/gems/1.8/gems/rake-0.8.7/lib/rake. rb:2029:in top_level' c:/Documents and Settings/pneve/ruby/lib/ruby/gems/1.8/gems/rake-0.8.7/lib/rake. rb:2029:ineach' c:/Documents and Settings/pneve/ruby/lib/ruby/gems/1.8/gems/rake-0.8.7/lib/rake. rb:2029:in top_level' c:/Documents and Settings/pneve/ruby/lib/ruby/gems/1.8/gems/rake-0.8.7/lib/rake. rb:2068:instandard_exception_handling' c:/Documents and Settings/pneve/ruby/lib/ruby/gems/1.8/gems/rake-0.8.7/lib/rake. rb:2023:in top_level' c:/Documents and Settings/pneve/ruby/lib/ruby/gems/1.8/gems/rake-0.8.7/lib/rake. rb:2001:inrun' c:/Documents and Settings/pneve/ruby/lib/ruby/gems/1.8/gems/rake-0.8.7/lib/rake. rb:2068:in standard_exception_handling' c:/Documents and Settings/pneve/ruby/lib/ruby/gems/1.8/gems/rake-0.8.7/lib/rake. rb:1998:inrun' c:/Documents and Settings/pneve/ruby/lib/ruby/gems/1.8/gems/rake-0.8.7/bin/rake: 31 c:/Documents and Settings/pneve/ruby/bin/rake:16:in `load' c:/Documents and Settings/pneve/ruby/bin/rake:16

  Read the article

• HELP!! Delayed-job: Rake aborted! Can't modify frozen hash

  - by pmneve

  Too bad even the trace doesn't say which hash is involved. Sorry this post is long: am trying to provide enough context to be meaningful. Occurs intermittently when rake jobs:work is pulling a command out of delayed_jobs while my status observer is in the process of parsing a log file for detailed results of the previous delayed_job denizen. I have an observer class (in RAILS_ROOT/lib ) which listens for the events, makes a copy of them and calls the owner class ( in apps/models ) which then calls on the log parser (also in /lib) to do the actual work. (Should both of those classes, the observer and the parser be in app/models?) Am due to deliver this application in a few days and this is killing it (and me). Am using DirectoryWatcher to look for flag files that indicate the start and finish of the delayed_jobs. That is started at the end of environment.rb like this: require 'directory_watcher' $scriptStatusObserver = ScriptStatusObserver.new dirToWatch ="#{RAILS_ROOT}/tmp/flags" $directoryWatcher = DirectoryWatcher.new( dirToWatch ) $directoryWatcher.glob= "*.flg" $directoryWatcher.interval=(15) $directoryWatcher.add_observer( $scriptStatusObserver ) $directoryWatcher.persist=("#{RAILS_ROOT}/tmp/flags/dw_state.yml") $directoryWatcher.start at_exit { $directoryWatcher.stop } This code is outside of the run method (btw is that the best place or is inside the run better?) Here is the observer: require 'script_run' class ScriptStatusObserver def initialize @rcvdEvents = [] end def update( *events ) begin puts "#{LINE.to_s}: ScriptStatusObserver events: \n"+events.to_yaml cnt = 0 events.each do |e| if e.to_s.match(/^\s*added/) cnt = cnt + 1 @rcvdEvents << e end end ScriptRun.new.catch_up( @rcvdEvents ) if cnt > 0 @rcvdEvents.clear rescue puts $! end end end Here is ScriptRun (it attaches to an associative table built with has_many:through) require 'observer' class ScriptRun < ActiveRecord::Base set_table_name "scripts_runs" belongs_to :script belongs_to :run def parse( result ) parser = LogParser.new parser.parse(result) end def catch_up( events ) events.each do |e| typ = e.type path = e.path thisMatch = path.match(/flags\/(\d+)_(\d+)_([\d\.]+)_(\w+)\.flg/) run_id = thisMatch[1] script_id = thisMatch[2] ts = thisMatch[3] status = thisMatch[4] if e.to_s.match(/^\s*added/) status_update( script_id, run_id, status, ts, path ) end end end def status_update( script_id, run_id, status, ts, path ) scriptrun = ScriptRun.find(:first, :conditions => [ "run_id = ? and script_id = ?", run_id.to_i, script_id.to_i ]) if scriptrun.kind_of?(ScriptRun) currStatus = scriptrun.status if not currStatus == 'completed' scriptrun.update_attribute(:status, status) if status == 'parse' flag = File.new(path) logSpec = flag.gets flag.close logName = File.basename(logSpec) logPath = logSpec.sub(logName, '') logName =~ /^(([\w_]+)_([\w]+)_(\d+))\.log$/ name = $1 basename = $2 runenv = $3 tsOrPid = $4 result = Result.new result.log_path = logPath result.basename = basename result.name = name result.script_id = script_id.to_i result.run_id = run_id.to_i if runenv == 'sit' runenv = 'SIT3348' end result.application_environment_id = ApplicationEnvironment.find(:first, :conditions => [ "nodename = ?", runenv]).id parse(result) if run_completed?( run_id ) myRun = Run.find(run_id.to_i) if myRun.kind_of?( Run ) myRun.update_attribute( :completed, Time.now.to_f ) end end end end else puts "#{__LINE__.to_s}: ScriptRun.status_update: ScriptRun not found for run #{run_id} script #{script_id} ts #{ts.to_s}" end File.delete(path) end def run_completed?( id ) scriptruns = ScriptRun.find(:all, :conditions = [ "run_id = ?", id.to_i] ) scriptruns.each do |sr| if not sr.status == 'completed' return false end end return true end end LogParser is too long even for this post but it reads the script log and pulls detailed information (counts and timings) out of the log and writes to a details table. It also tallies and calculates averages and rolls those up into summary tables for quicker access from the web pages. Here is the error trace: (don't ask why everything is under my Windows profile. It's a long story) Scanner running 1270239731.43 directory_watcher.notify_observers: #, #] update:[#, /pneve/workspace/waftt-0.29/tmp/flags/100039_18_1270239550.108_parse.flg"] rake aborted! can't modify frozen hash C:/Documents and Settings/pneve/workspace/waftt-0.29/vendor/rails/activerecord/l ib/active_record/attribute_methods.rb:313:in []=' C:/Documents and Settings/pneve/workspace/waftt-0.29/vendor/rails/activerecord/l ib/active_record/attribute_methods.rb:313:inwrite_attribute_without_dirty' C:/Documents and Settings/pneve/workspace/waftt-0.29/vendor/rails/activerecord/l ib/active_record/dirty.rb:139:in write_attribute' C:/Documents and Settings/pneve/workspace/waftt-0.29/vendor/rails/activerecord/l ib/active_record/attribute_methods.rb:211:inlast_error=' C:/Documents and Settings/pneve/workspace/waftt-0.29/vendor/plugins/delayed_job/ lib/delayed/worker.rb:141:in handle_failed_job' C:/Documents and Settings/pneve/workspace/waftt-0.29/vendor/plugins/delayed_job/ lib/delayed/worker.rb:115:inrun' C:/Documents and Settings/pneve/workspace/waftt-0.29/vendor/plugins/delayed_job/ lib/delayed/worker.rb:162:in reserve_and_run_one_job' C:/Documents and Settings/pneve/workspace/waftt-0.29/vendor/plugins/delayed_job/ lib/delayed/worker.rb:92:inwork_off' C:/Documents and Settings/pneve/workspace/waftt-0.29/vendor/plugins/delayed_job/ lib/delayed/worker.rb:91:in times' C:/Documents and Settings/pneve/workspace/waftt-0.29/vendor/plugins/delayed_job/ lib/delayed/worker.rb:91:inwork_off' C:/Documents and Settings/pneve/workspace/waftt-0.29/vendor/plugins/delayed_job/ lib/delayed/worker.rb:66:in start' C:/Documents and Settings/pneve/workspace/waftt-0.29/vendor/rails/activesupport/ lib/active_support/core_ext/benchmark.rb:10:inrealtime' C:/Documents and Settings/pneve/workspace/waftt-0.29/vendor/plugins/delayed_job/ lib/delayed/worker.rb:65:in start' C:/Documents and Settings/pneve/workspace/waftt-0.29/vendor/plugins/delayed_job/ lib/delayed/worker.rb:62:inloop' C:/Documents and Settings/pneve/workspace/waftt-0.29/vendor/plugins/delayed_job/ lib/delayed/worker.rb:62:in start' C:/Documents and Settings/pneve/workspace/waftt-0.29/vendor/plugins/delayed_job/ lib/delayed/tasks.rb:13 c:/Documents and Settings/pneve/ruby/lib/ruby/gems/1.8/gems/rake-0.8.7/lib/rake. rb:636:incall' c:/Documents and Settings/pneve/ruby/lib/ruby/gems/1.8/gems/rake-0.8.7/lib/rake. rb:636:in execute' c:/Documents and Settings/pneve/ruby/lib/ruby/gems/1.8/gems/rake-0.8.7/lib/rake. rb:631:ineach' c:/Documents and Settings/pneve/ruby/lib/ruby/gems/1.8/gems/rake-0.8.7/lib/rake. rb:631:in execute' c:/Documents and Settings/pneve/ruby/lib/ruby/gems/1.8/gems/rake-0.8.7/lib/rake. rb:597:ininvoke_with_call_chain' c:/Documents and Settings/pneve/ruby/lib/ruby/1.8/monitor.rb:242:in synchronize ' c:/Documents and Settings/pneve/ruby/lib/ruby/gems/1.8/gems/rake-0.8.7/lib/rake. rb:590:ininvoke_with_call_chain' c:/Documents and Settings/pneve/ruby/lib/ruby/gems/1.8/gems/rake-0.8.7/lib/rake. rb:583:in invoke' c:/Documents and Settings/pneve/ruby/lib/ruby/gems/1.8/gems/rake-0.8.7/lib/rake. rb:2051:ininvoke_task' c:/Documents and Settings/pneve/ruby/lib/ruby/gems/1.8/gems/rake-0.8.7/lib/rake. rb:2029:in top_level' c:/Documents and Settings/pneve/ruby/lib/ruby/gems/1.8/gems/rake-0.8.7/lib/rake. rb:2029:ineach' c:/Documents and Settings/pneve/ruby/lib/ruby/gems/1.8/gems/rake-0.8.7/lib/rake. rb:2029:in top_level' c:/Documents and Settings/pneve/ruby/lib/ruby/gems/1.8/gems/rake-0.8.7/lib/rake. rb:2068:instandard_exception_handling' c:/Documents and Settings/pneve/ruby/lib/ruby/gems/1.8/gems/rake-0.8.7/lib/rake. rb:2023:in top_level' c:/Documents and Settings/pneve/ruby/lib/ruby/gems/1.8/gems/rake-0.8.7/lib/rake. rb:2001:inrun' c:/Documents and Settings/pneve/ruby/lib/ruby/gems/1.8/gems/rake-0.8.7/lib/rake. rb:2068:in standard_exception_handling' c:/Documents and Settings/pneve/ruby/lib/ruby/gems/1.8/gems/rake-0.8.7/lib/rake. rb:1998:inrun' c:/Documents and Settings/pneve/ruby/lib/ruby/gems/1.8/gems/rake-0.8.7/bin/rake: 31 c:/Documents and Settings/pneve/ruby/bin/rake:16:in `load' c:/Documents and Settings/pneve/ruby/bin/rake:16

  Read the article

• JQuery Hover li Show div which sits outside li structure

  - by Dave_Stott

  Hi everyone I'm currently trying to create a "mega" dropout menu using JQuery but have encountered an issue I'm yet to be able to resolve. At the moment I have the following HTML structure: <div id="TopNav" class="grid_16"> <ul class="cmsListMenuUL level0" id="TopNavMenu"> <li class="cmsListMenuLIcmsListMenuLI highlightedLI" id="TopNavMenu_Home"><a href="/"> <span class="text">Home</span></a></li> <li class="cmsListMenuLIfirst" id="TopNavMenu_0_1"><a href="/Key-Sectors.aspx" class="cmsListMenuLink"> <span class="text">Key Sectors</span></a></li> <li class="cmsListMenuLI" id="TopNavMenu_0_2"><a href="/Global-Brands.aspx" class="cmsListMenuLink"> <span class="text">Global Brands</span></a></li> <li class="cmsListMenuLI" id="TopNavMenu_0_3"><a href="/News---Features.aspx" class="cmsListMenuLink"> <span class="text">News &amp; Features</span></a></li> <li class="cmsListMenuLI" id="TopNavMenu_0_4"><a href="/Videos.aspx" class="cmsListMenuLink"> <span class="text">Videos</span></a></li> <li class="cmsListMenuLI" id="TopNavMenu_0_5"><a href="/Events.aspx" class="cmsListMenuLink"> <span class="text">Events</span></a></li> <li class="cmsListMenuLI" id="TopNavMenu_0_6"><a href="/Key-Cities.aspx" class="cmsListMenuLink"> <span class="text">Key Cities</span></a></li> <li class="cmsListMenuLI" id="TopNavMenu_0_7"><a href="/Doing-Business-in-Yorkshire.aspx" class="cmsListMenuLink"><span class="text">Doing Business in Yorkshire</span></a></li> <li class="cmsListMenuLI" id="TopNavMenu_0_8"><a href="/How-We-Can-Help.aspx" class="cmsListMenuLink"> <span class="text">How We Can Help</span></a></li> <li class="cmsListMenuLI" id="TopNavMenu_0_9"><a href="/Contact-Us.aspx" class="cmsListMenuLink"> <span class="text">Contact Us</span></a></li> </ul> </div> <div class="sectorsDropped"> <div class="floatLeft leftColumn"> <div class="parentItem" style="border-color: #0064BE;"> <a href="/Key-Sectors/Advanced-Engineering---Materials.aspx" class="parentItemContent"> Advanced Engineering &amp; Materials</a><div class="childItem"> <a href="/Key-Sectors/Advanced-Engineering---Materials/Nuclear.aspx">- Nuclear</a></div> <div class="childItem"> <a href="/Key-Sectors/Advanced-Engineering---Materials/Logistics---Infrastructure.aspx"> - Logistics &amp; Infrastructure</a></div> </div> <div class="parentItem" style="border-color: #FFB611;"> <a href="/Key-Sectors/Chemicals.aspx" class="parentItemContent">Chemicals</a></div> <div class="parentItem" style="border-color: #B7CC0B;"> <a href="/Key-Sectors/Environmental-Technologies.aspx" class="parentItemContent">Environmental Technologies</a><div class="childItem"> <a href="/Key-Sectors/Environmental-Technologies/Offshore-Wind.aspx">- Offshore Wind</a></div> <div class="childItem"> <a href="/Key-Sectors/Environmental-Technologies/Carbon-Capture---Storage.aspx">- Carbon Capture &amp; Storage</a></div> <div class="childItem"> <a href="/Key-Sectors/Environmental-Technologies/Tidal-Power.aspx">- Tidal Power</a></div> <div class="childItem"> <a href="/Key-Sectors/Environmental-Technologies/Biomass.aspx">- Biomass</a></div> </div> </div> <div class="floatLeft rightColumn"> <div class="parentItem" style="border-color: #AC26AA;"> <a href="/Key-Sectors/Digital---New-Media.aspx" class="parentItemContent">Digital &amp; New Media</a></div> <div class="parentItem" style="border-color: #e1477e;"> <a href="/Key-Sectors/Food---Drink.aspx" class="parentItemContent">Food &amp; Drink</a></div> <div class="parentItem" style="border-color: #00c5b5;"> <a href="/Key-Sectors/Healthcare-Technologies.aspx" class="parentItemContent">Healthcare Technologies</a><div class="childItem"> <a href="/Key-Sectors/Healthcare-Technologies/Biotechnology.aspx">- Biotechnology</a></div> <div class="childItem"> <a href="/Key-Sectors/Healthcare-Technologies/Pharmaceuticals.aspx">- Pharmaceuticals</a></div> <div class="childItem"> <a href="/Key-Sectors/Healthcare-Technologies/Medical-Devices.aspx">- Medical Devices</a></div> </div> <div class="parentItem" style="border-color: #AC1A2F;"> <a href="/Key-Sectors/Financial---Professional.aspx" class="parentItemContent">Financial &amp; Professional</a></div> </div> </div> In normal circumstances the div containing the "mega" menu options would sit inside the li item that fires the show/hide but this is currently not possible as the ul list of navigation links is rendered using a 3rd party piece of software which does not provide an equivalent of an OnItemDataBound event for me to be able to inject the div into the item Does anyone know of a way, using JQuery, of showing the div but maintain the display of the div as the mouse focus leaves the li that originaly displayed the div and actually enters the div? I'm currently using the following JQuery which displays the div correctly but as the mouse focus enters the div the div then disappears as the mouse focus from the li has now moved: $(document).ready(function() { function addMega(){ $(".sectorsDropped").toggle("fast"); } function removeMega(){ $(".sectorsDropped").toggle("fast"); } var megaConfig = { interval: 500, sensitivity: 4, over: addMega, timeout: 500, out: removeMega }; $("#TopNavMenu_0_1").hoverIntent(megaConfig) }); Thanks Dave

  Read the article

• Shorter Rails routes

  - by Puru puru rin..

  Hello, I have a thing blog application, and I would like to shorten my routes. Here there are: Blog::Application.routes.draw do resources :categories do resources :articles do resources :comments end end A rake routes command build the following lines: GET /categories/:category_id/articles/:article_id/comments(.:format) {:controller=>"comments", :action=>"index"} category_article_comments POST /categories/:category_id/articles/:article_id/comments(.:format) {:controller=>"comments", :action=>"create"} new_category_article_comment GET /categories/:category_id/articles/:article_id/comments/new(.:format) {:controller=>"comments", :action=>"new"} GET /categories/:category_id/articles/:article_id/comments/:id(.:format) {:controller=>"comments", :action=>"show"} PUT /categories/:category_id/articles/:article_id/comments/:id(.:format) {:controller=>"comments", :action=>"update"} category_article_comment DELETE /categories/:category_id/articles/:article_id/comments/:id(.:format) {:controller=>"comments", :action=>"destroy"} edit_category_article_comment GET /categories/:category_id/articles/:article_id/comments/:id/edit(.:format) {:controller=>"comments", :action=>"edit"} GET /categories/:category_id/articles(.:format) {:controller=>"articles", :action=>"index"} category_articles POST /categories/:category_id/articles(.:format) {:controller=>"articles", :action=>"create"} new_category_article GET /categories/:category_id/articles/new(.:format) {:controller=>"articles", :action=>"new"} GET /categories/:category_id/articles/:id(.:format) {:controller=>"articles", :action=>"show"} PUT /categories/:category_id/articles/:id(.:format) {:controller=>"articles", :action=>"update"} category_article DELETE /categories/:category_id/articles/:id(.:format) {:controller=>"articles", :action=>"destroy"} edit_category_article GET /categories/:category_id/articles/:id/edit(.:format) {:controller=>"articles", :action=>"edit"} GET /categories(.:format) {:controller=>"categories", :action=>"index"} categories POST /categories(.:format) {:controller=>"categories", :action=>"create"} new_category GET /categories/new(.:format) {:controller=>"categories", :action=>"new"} GET /categories/:id(.:format) {:controller=>"categories", :action=>"show"} PUT /categories/:id(.:format) {:controller=>"categories", :action=>"update"} category DELETE /categories/:id(.:format) {:controller=>"categories", :action=>"destroy"} edit_category GET /categories/:id/edit(.:format) {:controller=>"categories", :action=>"edit"} As can be seen, each resource is ordered in a tree. So I believe that, it's could be interesting to simplify my routes such as for example: /categories/ => / /categories/:id => /:id /categories/:category_id/articles/ => /:category_id/articles /categories/:category_id/articles/:id => /:category_id/:id /categories/:category_id/articles/:article_id/comments/ => /:category_id/:article_id/comments /categories/:category_id/articles/:article_id/comments/:id => /:category_id/:article_id/:id It's more DRY, is't it? :) Does Rails 3 provides a easy way to do so, with an HTTP verbs mapping to controller actions automatically? Thanks anyone.

  Read the article

• File Fix-it codegolf (GCJ 2010 1B-A)

  - by KirarinSnow

  Last year (2009), the Google Code Jam featured an interesting problem as the first problem in Round 1B: Decision Tree As the problem seemed tailored for Lisp-like languages, we spontaneously had an exciting codegolf here on SO, in which a few languages managed to solve the problem in fewer characters than any Lisp variety, using quite a number of different techniques. This year's Round 1B Problem A (File Fix-it) also seems tailored for a particular family of languages, Unix shell scripts. So continuing the "1B-A tradition" would be appropriate. :p But which language will end up with the shortest code? Let us codegolf and see! Problem description (adapted from official page): You are given T test cases. Each test case contains N lines that list the full path of all directories currently existing on your computer. For example: /home/awesome /home/awesome/wheeeeeee /home/awesome/wheeeeeee/codegolfrocks /home/thecakeisalie Next, you are given M lines that list the full path of directories you would like to create. They are in the same format as the previous examples. You can create a directory using the mkdir command, but you can only do so if the parent directory already exists. For example, to create the directories /pyonpyon/fumufumu/yeahyeah and /pyonpyon/fumufumu/yeahyeahyeah, you would need to use mkdir four times: mkdir /pyonpyon mkdir /pyonpyon/fumufumu mkdir /pyonpyon/fumufumu/yeahyeah mkdir /pyonpyon/fumufumu/yeahyeahyeah For each test case, return the number of times you have to call mkdir to create all the directories you would like to create. Input Input consists of a text file whose first line contains the integer T, the number of test cases. The rest of the file contains the test cases. Each test case begins with a line containing the integers N and M, separated by a space. The next N lines contain the path of each directory currently existing on your computer (not including the root directory /). This is a concatenation of one or more non-empty lowercase alphanumeric strings, each preceded by a single /. The following M lines contain the path of each directory you would like to create. Output For each case, print one line containing Case #X: Y, where X is the case number and Y is the solution. Limits 1 = T = 100. 0 = N = 100. 1 = M = 100. Each path contains at most 100 characters. Every path appears only once in the list of directories already on your computer, or in the list of desired directories. However, a path may appear on both lists, as in example case #3 below. If a directory is in the list of directories already on your computer, its parent directory will also be listed, with the exception of the root directory /. The input file is at most 100,000 bytes long. Example Larger sample test cases may be downloaded here. Input: 3 0 2 /home/sparkle/pyon /home/sparkle/cakes 1 3 /z /z/y /z/x /y/y 2 1 /moo /moo/wheeeee /moo Output: Case #1: 4 Case #2: 4 Case #3: 0 Code Golf Please post your shortest code in any language that solves this problem. Input and output may be handled via stdin and stdout or by other files of your choice. Please include a disclaimer if your code has the potential to modify or delete existing files when executed. Winner will be the shortest solution (by byte count) in a language with an implementation existing prior to the start of Round 1B 2010.

  Read the article

• Minimum-Waste Print Job Grouping Algorithm?

  - by Matt Mc

  I work at a publishing house and I am setting up one of our presses for "ganging", in other words, printing multiple jobs simultaneously. Given that different print jobs can have different quantities, and anywhere from 1 to 20 jobs might need to be considered at a time, the problem would be to determine which jobs to group together to minimize waste (waste coming from over-printing on smaller-quantity jobs in a given set, that is). Given the following stable data: All jobs are equal in terms of spatial size--placement on paper doesn't come into consideration. There are three "lanes", meaning that three jobs can be printed simultaneously. Ideally, each lane has one job. Part of the problem is minimizing how many lanes each job is run on. If necessary, one job could be run on two lanes, with a second job on the third lane. The "grouping" waste from a given set of jobs (let's say the quantities of them are x, y and z) would be the highest number minus the two lower numbers. So if x is the higher number, the grouping waste would be (x - y) + (x - z). Otherwise stated, waste is produced by printing job Y and Z (in excess of their quantities) up to the quantity of X. The grouping waste would be a qualifier for the given set, meaning it could not exceed a certain quantity or the job would simply be printed alone. So the question is stated: how to determine which sets of jobs are grouped together, out of any given number of jobs, based on the qualifiers of 1) Three similar quantities OR 2) Two quantities where one is approximately double the other, AND with the aim of minimal total grouping waste across the various sets. (Edit) Quantity Information: Typical job quantities can be from 150 to 350 on foreign languages, or 500 to 1000 on English print runs. This data can be used to set up some scenarios for an algorithm. For example, let's say you had 5 jobs: 1000, 500, 500, 450, 250 By looking at it, I can see a couple of answers. Obviously (1000/500/500) is not efficient as you'll have a grouping waste of 1000. (500/500/450) is better as you'll have a waste of 50, but then you run (1000) and (250) alone. But you could also run (1000/500) with 1000 on two lanes, (500/250) with 500 on two lanes and then (450) alone. In terms of trade-offs for lane minimization vs. wastage, we could say that any grouping waste over 200 is excessive. (End Edit) ...Needless to say, quite a problem. (For me.) I am a moderately skilled programmer but I do not have much familiarity with algorithms and I am not fully studied in the mathematics of the area. I'm I/P writing a sort of brute-force program that simply tries all options, neglecting any option tree that seems to have excessive grouping waste. However, I can't help but hope there's an easier and more efficient method. I've looked at various websites trying to find out more about algorithms in general and have been slogging my way through the symbology, but it's slow going. Unfortunately, Wikipedia's articles on the subject are very cross-dependent and it's difficult to find an "in". The only thing I've been able to really find would seem to be a definition of the rough type of algorithm I need: "Exclusive Distance Clustering", one-dimensionally speaking. I did look at what seems to be the popularly referred-to algorithm on this site, the Bin Packing one, but I was unable to see exactly how it would work with my problem. Any help is appreciated. :)

  Read the article

• FreeBSD 8.1 unstable network connection

  - by frankcheong

  I have three FreeBSD 8.1 running on three different hardware and therefore consist of different network adapter as well (bce, bge and igb). I found that the network connection is kind of unstable which I have tried to scp some 10MB file and found that I cannot always get the files completed successfully. I have further checked with my network admin and he claim that the problem is being caused by the network driver which cannot support the load whereby he tried to ping using huge packet size (around 15k) and my server will drop packet consistently at a regular interval. I found that this statement may not be valid since the three server is using three different network drive and it would be quite impossible that the same problem is being caused by three different network adapter and thus different network driver. Since then I have tried to tune up the performance by playing around with the /etc/sysctl.conf figures with no luck. kern.ipc.somaxconn=1024 kern.ipc.shmall=3276800 kern.ipc.shmmax=1638400000 # Security net.inet.ip.redirect=0 net.inet.ip.sourceroute=0 net.inet.ip.accept_sourceroute=0 net.inet.icmp.maskrepl=0 net.inet.icmp.log_redirect=0 net.inet.icmp.drop_redirect=1 net.inet.tcp.drop_synfin=1 # Security net.inet.udp.blackhole=1 net.inet.tcp.blackhole=2 # Required by pf net.inet.ip.forwarding=1 #Network Performance Tuning kern.ipc.maxsockbuf=16777216 net.inet.tcp.rfc1323=1 net.inet.tcp.sendbuf_max=16777216 net.inet.tcp.recvbuf_max=16777216 # Setting specifically for 1 or even 10Gbps network net.local.stream.sendspace=262144 net.local.stream.recvspace=262144 net.inet.tcp.local_slowstart_flightsize=10 net.inet.tcp.nolocaltimewait=1 net.inet.tcp.mssdflt=1460 net.inet.tcp.sendbuf_auto=1 net.inet.tcp.sendbuf_inc=16384 net.inet.tcp.recvbuf_auto=1 net.inet.tcp.recvbuf_inc=524288 net.inet.tcp.sendspace=262144 net.inet.tcp.recvspace=262144 net.inet.udp.recvspace=262144 kern.ipc.maxsockbuf=16777216 kern.ipc.nmbclusters=32768 net.inet.tcp.delayed_ack=1 net.inet.tcp.delacktime=100 net.inet.tcp.slowstart_flightsize=179 net.inet.tcp.inflight.enable=1 net.inet.tcp.inflight.min=6144 # Reduce the cache size of slow start connection net.inet.tcp.hostcache.expire=1 Our network admin also claim that they see quite a lot of network up and down from their cisco switch log while I cannot find any up down message inside the dmesg. Have further checked the netstat -s but dont have concrete idea. tcp: 133695291 packets sent 39408539 data packets (3358837321 bytes) 61868 data packets (89472844 bytes) retransmitted 24 data packets unnecessarily retransmitted 0 resends initiated by MTU discovery 50756141 ack-only packets (2148 delayed) 0 URG only packets 0 window probe packets 4372385 window update packets 39781869 control packets 134898031 packets received 72339403 acks (for 3357601899 bytes) 190712 duplicate acks 0 acks for unsent data 59339201 packets (3647021974 bytes) received in-sequence 114 completely duplicate packets (135202 bytes) 27 old duplicate packets 0 packets with some dup. data (0 bytes duped) 42090 out-of-order packets (60817889 bytes) 0 packets (0 bytes) of data after window 0 window probes 3953896 window update packets 64181 packets received after close 0 discarded for bad checksums 0 discarded for bad header offset fields 0 discarded because packet too short 45192 discarded due to memory problems 19945391 connection requests 1323420 connection accepts 0 bad connection attempts 0 listen queue overflows 0 ignored RSTs in the windows 21133581 connections established (including accepts) 21268724 connections closed (including 32737 drops) 207874 connections updated cached RTT on close 207874 connections updated cached RTT variance on close 132439 connections updated cached ssthresh on close 42392 embryonic connections dropped 72339338 segments updated rtt (of 69477829 attempts) 390871 retransmit timeouts 0 connections dropped by rexmit timeout 0 persist timeouts 0 connections dropped by persist timeout 0 Connections (fin_wait_2) dropped because of timeout 13990 keepalive timeouts 2 keepalive probes sent 13988 connections dropped by keepalive 173044 correct ACK header predictions 36947371 correct data packet header predictions 1323420 syncache entries added 0 retransmitted 0 dupsyn 0 dropped 1323420 completed 0 bucket overflow 0 cache overflow 0 reset 0 stale 0 aborted 0 badack 0 unreach 0 zone failures 1323420 cookies sent 0 cookies received 1864 SACK recovery episodes 18005 segment rexmits in SACK recovery episodes 26066896 byte rexmits in SACK recovery episodes 147327 SACK options (SACK blocks) received 87473 SACK options (SACK blocks) sent 0 SACK scoreboard overflow 0 packets with ECN CE bit set 0 packets with ECN ECT(0) bit set 0 packets with ECN ECT(1) bit set 0 successful ECN handshakes 0 times ECN reduced the congestion window udp: 5141258 datagrams received 0 with incomplete header 0 with bad data length field 0 with bad checksum 1 with no checksum 0 dropped due to no socket 129616 broadcast/multicast datagrams undelivered 0 dropped due to full socket buffers 0 not for hashed pcb 5011642 delivered 5016050 datagrams output 0 times multicast source filter matched sctp: 0 input packets 0 datagrams 0 packets that had data 0 input SACK chunks 0 input DATA chunks 0 duplicate DATA chunks 0 input HB chunks 0 HB-ACK chunks 0 input ECNE chunks 0 input AUTH chunks 0 chunks missing AUTH 0 invalid HMAC ids received 0 invalid secret ids received 0 auth failed 0 fast path receives all one chunk 0 fast path multi-part data 0 output packets 0 output SACKs 0 output DATA chunks 0 retransmitted DATA chunks 0 fast retransmitted DATA chunks 0 FR's that happened more than once to same chunk 0 intput HB chunks 0 output ECNE chunks 0 output AUTH chunks 0 ip_output error counter Packet drop statistics: 0 from middle box 0 from end host 0 with data 0 non-data, non-endhost 0 non-endhost, bandwidth rep only 0 not enough for chunk header 0 not enough data to confirm 0 where process_chunk_drop said break 0 failed to find TSN 0 attempt reverse TSN lookup 0 e-host confirms zero-rwnd 0 midbox confirms no space 0 data did not match TSN 0 TSN's marked for Fast Retran Timeouts: 0 iterator timers fired 0 T3 data time outs 0 window probe (T3) timers fired 0 INIT timers fired 0 sack timers fired 0 shutdown timers fired 0 heartbeat timers fired 0 a cookie timeout fired 0 an endpoint changed its cookiesecret 0 PMTU timers fired 0 shutdown ack timers fired 0 shutdown guard timers fired 0 stream reset timers fired 0 early FR timers fired 0 an asconf timer fired 0 auto close timer fired 0 asoc free timers expired 0 inp free timers expired 0 packet shorter than header 0 checksum error 0 no endpoint for port 0 bad v-tag 0 bad SID 0 no memory 0 number of multiple FR in a RTT window 0 RFC813 allowed sending 0 RFC813 does not allow sending 0 times max burst prohibited sending 0 look ahead tells us no memory in interface 0 numbers of window probes sent 0 times an output error to clamp down on next user send 0 times sctp_senderrors were caused from a user 0 number of in data drops due to chunk limit reached 0 number of in data drops due to rwnd limit reached 0 times a ECN reduced the cwnd 0 used express lookup via vtag 0 collision in express lookup 0 times the sender ran dry of user data on primary 0 same for above 0 sacks the slow way 0 window update only sacks sent 0 sends with sinfo_flags !=0 0 unordered sends 0 sends with EOF flag set 0 sends with ABORT flag set 0 times protocol drain called 0 times we did a protocol drain 0 times recv was called with peek 0 cached chunks used 0 cached stream oq's used 0 unread messages abandonded by close 0 send burst avoidance, already max burst inflight to net 0 send cwnd full avoidance, already max burst inflight to net 0 number of map array over-runs via fwd-tsn's ip: 137814085 total packets received 0 bad header checksums 0 with size smaller than minimum 0 with data size < data length 0 with ip length > max ip packet size 0 with header length < data size 0 with data length < header length 0 with bad options 0 with incorrect version number 1200 fragments received 0 fragments dropped (dup or out of space) 0 fragments dropped after timeout 300 packets reassembled ok 137813009 packets for this host 530 packets for unknown/unsupported protocol 0 packets forwarded (0 packets fast forwarded) 61 packets not forwardable 0 packets received for unknown multicast group 0 redirects sent 137234598 packets sent from this host 0 packets sent with fabricated ip header 685307 output packets dropped due to no bufs, etc. 52 output packets discarded due to no route 300 output datagrams fragmented 1200 fragments created 0 datagrams that can't be fragmented 0 tunneling packets that can't find gif 0 datagrams with bad address in header icmp: 0 calls to icmp_error 0 errors not generated in response to an icmp message Output histogram: echo reply: 305 0 messages with bad code fields 0 messages less than the minimum length 0 messages with bad checksum 0 messages with bad length 0 multicast echo requests ignored 0 multicast timestamp requests ignored Input histogram: destination unreachable: 530 echo: 305 305 message responses generated 0 invalid return addresses 0 no return routes ICMP address mask responses are disabled igmp: 0 messages received 0 messages received with too few bytes 0 messages received with wrong TTL 0 messages received with bad checksum 0 V1/V2 membership queries received 0 V3 membership queries received 0 membership queries received with invalid field(s) 0 general queries received 0 group queries received 0 group-source queries received 0 group-source queries dropped 0 membership reports received 0 membership reports received with invalid field(s) 0 membership reports received for groups to which we belong 0 V3 reports received without Router Alert 0 membership reports sent arp: 376748 ARP requests sent 3207 ARP replies sent 245245 ARP requests received 80845 ARP replies received 326090 ARP packets received 267712 total packets dropped due to no ARP entry 108876 ARP entrys timed out 0 Duplicate IPs seen ip6: 2226633 total packets received 0 with size smaller than minimum 0 with data size < data length 0 with bad options 0 with incorrect version number 0 fragments received 0 fragments dropped (dup or out of space) 0 fragments dropped after timeout 0 fragments that exceeded limit 0 packets reassembled ok 2226633 packets for this host 0 packets forwarded 0 packets not forwardable 0 redirects sent 2226633 packets sent from this host 0 packets sent with fabricated ip header 0 output packets dropped due to no bufs, etc. 8 output packets discarded due to no route 0 output datagrams fragmented 0 fragments created 0 datagrams that can't be fragmented 0 packets that violated scope rules 0 multicast packets which we don't join Input histogram: UDP: 2226633 Mbuf statistics: 962679 one mbuf 1263954 one ext mbuf 0 two or more ext mbuf 0 packets whose headers are not continuous 0 tunneling packets that can't find gif 0 packets discarded because of too many headers 0 failures of source address selection Source addresses selection rule applied: icmp6: 0 calls to icmp6_error 0 errors not generated in response to an icmp6 message 0 errors not generated because of rate limitation 0 messages with bad code fields 0 messages < minimum length 0 bad checksums 0 messages with bad length Histogram of error messages to be generated: 0 no route 0 administratively prohibited 0 beyond scope 0 address unreachable 0 port unreachable 0 packet too big 0 time exceed transit 0 time exceed reassembly 0 erroneous header field 0 unrecognized next header 0 unrecognized option 0 redirect 0 unknown 0 message responses generated 0 messages with too many ND options 0 messages with bad ND options 0 bad neighbor solicitation messages 0 bad neighbor advertisement messages 0 bad router solicitation messages 0 bad router advertisement messages 0 bad redirect messages 0 path MTU changes rip6: 0 messages received 0 checksum calculations on inbound 0 messages with bad checksum 0 messages dropped due to no socket 0 multicast messages dropped due to no socket 0 messages dropped due to full socket buffers 0 delivered 0 datagrams output netstat -m 516/5124/5640 mbufs in use (current/cache/total) 512/1634/2146/32768 mbuf clusters in use (current/cache/total/max) 512/1536 mbuf+clusters out of packet secondary zone in use (current/cache) 0/1303/1303/12800 4k (page size) jumbo clusters in use (current/cache/total/max) 0/0/0/6400 9k jumbo clusters in use (current/cache/total/max) 0/0/0/3200 16k jumbo clusters in use (current/cache/total/max) 1153K/9761K/10914K bytes allocated to network (current/cache/total) 0/0/0 requests for mbufs denied (mbufs/clusters/mbuf+clusters) 0/0/0 requests for jumbo clusters denied (4k/9k/16k) 0/8/6656 sfbufs in use (current/peak/max) 0 requests for sfbufs denied 0 requests for sfbufs delayed 0 requests for I/O initiated by sendfile 0 calls to protocol drain routines Anyone got an idea what might be the possible cause?

  Read the article

• parseInt and viewflipper layout problems

  - by user1234167

  I have a problem with parseInt it throws the error: unable to parse 'null' as integer. My view flipper is also not working. Hopefully this is an easy enough question. Here is my activity: import javax.xml.parsers.SAXParser; import javax.xml.parsers.SAXParserFactory; import org.xml.sax.InputSource; import org.xml.sax.XMLReader; import android.app.Activity; import android.graphics.Color; import android.os.Bundle; import android.util.Log; import android.view.View; import android.view.View.OnClickListener; import android.widget.Button; import android.widget.LinearLayout; import android.widget.TextView; import android.widget.ViewFlipper; import xml.parser.dataset; public class XmlParserActivity extends Activity implements OnClickListener { private final String MY_DEBUG_TAG = "WeatherForcaster"; // private dataset myDataSet; private LinearLayout layout; private int temp= 0; /** Called when the activity is first created. */ //the ViewSwitcher private Button btn; private ViewFlipper flip; // private TextView tv; @Override public void onCreate(Bundle savedInstanceState) { super.onCreate(savedInstanceState); setContentView(R.layout.main); layout=(LinearLayout)findViewById(R.id.linearlayout1); btn=(Button)findViewById(R.id.btn); btn.setOnClickListener(this); flip=(ViewFlipper)findViewById(R.id.flip); //when a view is displayed flip.setInAnimation(this,android.R.anim.fade_in); //when a view disappears flip.setOutAnimation(this, android.R.anim.fade_out); // String postcode = null; // public String getPostcode { // return postcode; // } //URL newUrl = c; // myweather.setText(c.toString()); /* Create a new TextView to display the parsingresult later. */ TextView tv = new TextView(this); // run(0); //WeatherApplicationActivity postcode = new WeatherApplicationActivity(); try { /* Create a URL we want to load some xml-data from. */ URL url = new URL("http://new.myweather2.com/developer/forecast.ashx?uac=gcV3ynNdoV&output=xml&query=G41"); //String url = new String("http://new.myweather2.com/developer/forecast.ashx?uac=gcV3ynNdoV&output=xml&query="+WeatherApplicationActivity.postcode ); //URL url = new URL(url); //url.toString( ); //myString(url.toString() + WeatherApplicationActivity.getString(postcode)); // url + WeatherApplicationActivity.getString(postcode); /* Get a SAXParser from the SAXPArserFactory. */ SAXParserFactory spf = SAXParserFactory.newInstance(); SAXParser sp = spf.newSAXParser(); /* Get the XMLReader of the SAXParser we created. */ XMLReader xr = sp.getXMLReader(); /* Create a new ContentHandler and apply it to the XML-Reader*/ handler myHandler = new handler(); xr.setContentHandler(myHandler); /* Parse the xml-data from our URL. */ xr.parse(new InputSource(url.openStream())); /* Parsing has finished. */ /* Our ExampleHandler now provides the parsed data to us. */ dataset parsedDataSet = myHandler.getParsedData(); /* Set the result to be displayed in our GUI. */ tv.setText(parsedDataSet.toString()); } catch (Exception e) { /* Display any Error to the GUI. */ tv.setText("Error: " + e.getMessage()); Log.e(MY_DEBUG_TAG, "WeatherQueryError", e); } temp = Integer.parseInt(xml.parser.dataset.getTemp()); if(temp <0){ //layout.setBackgroundColor(Color.BLUE); //layout.setBackgroundColor(getResources().getColor(R.color.silver)); findViewById(R.id.flip).setBackgroundColor(Color.BLUE); } else if(temp > 0 && temp < 9) { //layout.setBackgroundColor(Color.GREEN); //layout.setBackgroundColor(getResources().getColor(R.color.silver)); findViewById(R.id.flip).setBackgroundColor(Color.GREEN); } else { //layout.setBackgroundColor(Color.YELLOW); //layout.setBackgroundColor(getResources().getColor(R.color.silver)); findViewById(R.id.flip).setBackgroundColor(Color.YELLOW); } /* Display the TextView. */ this.setContentView(tv); } @Override public void onClick(View arg0) { // TODO Auto-generated method stub onClick(View arg0) { // TODO Auto-generated method stub flip.showNext(); //specify flipping interval //flip.setFlipInterval(1000); //flip.startFlipping(); } } this is my dataset: package xml.parser; public class dataset { static String temp = null; // private int extractedInt = 0; public static String getTemp() { return temp; } public void setTemp(String temp) { this.temp = temp; } this is my handler: public void characters(char ch[], int start, int length) { if(this.in_temp){ String setTemp = new String(ch, start, length); // myParsedDataSet.setTempUnit(new String(ch, start, length)); // myParsedDataSet.setTemp; } the dataset and handler i only pasted the code that involves the temp as i no they r working when i take out the if statement. However even then my viewflipper wont work. This is my main xml: <?xml version="1.0" encoding="utf-8"?> <LinearLayout xmlns:android="http://schemas.android.com/apk/res/android" android:orientation="vertical" android:layout_width="fill_parent" android:layout_height="fill_parent" android:id="@+id/linearlayout1" > <TextView android:layout_width="fill_parent" android:layout_height="wrap_content" android:textSize="25dip" android:text="Flip Example" /> <TextView android:layout_width="fill_parent" android:layout_height="wrap_content" android:textSize="25dip" android:id="@+id/tv" /> <Button android:layout_width="wrap_content" android:layout_height="wrap_content" android:textSize="25dip" android:text="Flip" android:id="@+id/btn" android:onClick="ClickHandler" /> <ViewFlipper android:layout_width="fill_parent" android:layout_height="fill_parent" android:id="@+id/flip"> <LinearLayout android:orientation="vertical" android:layout_width="fill_parent" android:layout_height="fill_parent" > <TextView android:layout_width="fill_parent" android:layout_height="wrap_content" android:textSize="25dip" android:text="Item1a" /> </LinearLayout> <TextView android:layout_width="fill_parent" android:layout_height="wrap_content" android:textSize="25dip" android:id="@+id/tv2" /> </ViewFlipper> </LinearLayout> this is my logcat: 04-01 18:02:24.744: E/AndroidRuntime(7331): FATAL EXCEPTION: main 04-01 18:02:24.744: E/AndroidRuntime(7331): java.lang.RuntimeException: Unable to start activity ComponentInfo{xml.parser/xml.parser.XmlParserActivity}: java.lang.NumberFormatException: unable to parse 'null' as integer 04-01 18:02:24.744: E/AndroidRuntime(7331): at android.app.ActivityThread.performLaunchActivity(ActivityThread.java:1830) 04-01 18:02:24.744: E/AndroidRuntime(7331): at android.app.ActivityThread.handleLaunchActivity(ActivityThread.java:1851) 04-01 18:02:24.744: E/AndroidRuntime(7331): at android.app.ActivityThread.access$1500(ActivityThread.java:132) 04-01 18:02:24.744: E/AndroidRuntime(7331): at android.app.ActivityThread$H.handleMessage(ActivityThread.java:1038) 04-01 18:02:24.744: E/AndroidRuntime(7331): at android.os.Handler.dispatchMessage(Handler.java:99) 04-01 18:02:24.744: E/AndroidRuntime(7331): at android.os.Looper.loop(Looper.java:150) 04-01 18:02:24.744: E/AndroidRuntime(7331): at android.app.ActivityThread.main(ActivityThread.java:4293) 04-01 18:02:24.744: E/AndroidRuntime(7331): at java.lang.reflect.Method.invokeNative(Native Method) 04-01 18:02:24.744: E/AndroidRuntime(7331): at java.lang.reflect.Method.invoke(Method.java:507) 04-01 18:02:24.744: E/AndroidRuntime(7331): at com.android.internal.os.ZygoteInit$MethodAndArgsCaller.run(ZygoteInit.java:849) 04-01 18:02:24.744: E/AndroidRuntime(7331): at com.android.internal.os.ZygoteInit.main(ZygoteInit.java:607) 04-01 18:02:24.744: E/AndroidRuntime(7331): at dalvik.system.NativeStart.main(Native Method) 04-01 18:02:24.744: E/AndroidRuntime(7331): Caused by: java.lang.NumberFormatException: unable to parse 'null' as integer 04-01 18:02:24.744: E/AndroidRuntime(7331): at java.lang.Integer.parseInt(Integer.java:356) 04-01 18:02:24.744: E/AndroidRuntime(7331): at java.lang.Integer.parseInt(Integer.java:332) 04-01 18:02:24.744: E/AndroidRuntime(7331): at xml.parser.XmlParserActivity.onCreate(XmlParserActivity.java:118) 04-01 18:02:24.744: E/AndroidRuntime(7331): at android.app.Instrumentation.callActivityOnCreate(Instrumentation.java:1072) 04-01 18:02:24.744: E/AndroidRuntime(7331): at android.app.ActivityThread.performLaunchActivity(ActivityThread.java:1794) I hope I have given enough information about my problems. I will be extremely grateful if anyone can help me out.

  Read the article

• Flex 4: Traversing the Stage More Easily

  - by Steve

  The following is a MXML Module I am producing in Flex 4: <?xml version="1.0" encoding="utf-8"?> <mx:Module xmlns:fx="http://ns.adobe.com/mxml/2009" xmlns:s="library://ns.adobe.com/flex/spark" xmlns:mx="library://ns.adobe.com/flex/mx" creationComplete="init()" layout="absolute" width="100%" height="100%"> <fx:Declarations> <!-- Place non-visual elements (e.g., services, value objects) here --> </fx:Declarations> <fx:Style source="BMChartModule.css" /> <s:Panel id="panel" title="Benchmark Results" height="100%" width="100%" dropShadowVisible="false"> <mx:TabNavigator id="tn" height="100%" width="100%" /> </s:Panel> <fx:Script> <![CDATA[ import flash.events.Event; import mx.charts.ColumnChart; import mx.charts.effects.SeriesInterpolate; import mx.controls.Alert; import spark.components.BorderContainer; import spark.components.Button; import spark.components.Label; import spark.components.NavigatorContent; import spark.components.RadioButton; import spark.components.TextInput; import spark.layouts.*; private var xml:XML; private function init():void { var seriesInterpolate:SeriesInterpolate = new SeriesInterpolate(); seriesInterpolate.duration = 1000; xml = parentApplication.model.xml; var sectorList:XMLList = xml.SECTOR; for each(var i:XML in sectorList) { var ncLayout:HorizontalLayout = new HorizontalLayout(); var nc:NavigatorContent = new NavigatorContent(); nc.label = i.@NAME; nc.name = "NC_" + nc.label; nc.layout = ncLayout; tn.addElement(nc); var cC:ColumnChart = new ColumnChart(); cC.percentWidth = 70; cC.name = "CC"; nc.addElement(cC); var bClayout:VerticalLayout = new VerticalLayout(); var bC:BorderContainer = new BorderContainer(); bC.percentWidth = 30; bC.layout = bClayout; nc.addElement(bC); var bClabel:Label = new Label(); bClabel.percentWidth = 100; bClabel.text = "Select a graph to view it in the column chart:"; var dpList:XMLList = sectorList.(@NAME == i.@NAME).DATAPOINT; for each(var j:XML in dpList) { var rB:RadioButton = new RadioButton(); rB.groupName = "dp"; rB.label = j.@NAME; rB.addEventListener(MouseEvent.CLICK, rBclick); bC.addElement(rB); } } } private function rBclick(e:MouseEvent):void { var selectedTab:NavigatorContent = this.tn.selectedChild as NavigatorContent; var colChart:ColumnChart = selectedTab.getChildByName("CC") as ColumnChart; trace(selectedTab.getChildAt(0)); } ]]> </fx:Script> </mx:Module> I'm writing this function rBclick to redraw the column chart when a radio button is clicked. In order to do this I need to find the column chart on the stage using actionscript. I've currently got 3 lines of code in here to do this: var selectedTab:NavigatorContent = this.tn.selectedChild as NavigatorContent; var colChart:ColumnChart = selectedTab.getChildByName("CC") as ColumnChart; trace(selectedTab.getChildAt(0)); Getting to the active tab in the tabnavigator is easy enough, but then selectedTab.getChildAt(0) - which I was expecting to be the chart - is a "spark.skin.spark.SkinnableContainerSkin"...anyway, I can continue to traverse the tree using this somewhat annoying code, but I'm hoping there is an easier way. So in short, at run time I want to, with as little code as possible, identify the column chart in the active tab so I can redraw it. Any advice would be greatly appreciated.

  Read the article

• Setting an XAML Window always on top (but no TopMost property)

  - by Brian Scherady

  I am developing an application based on OptiTrack SDK (from NaturalPoint). I need to run the application window as "Always on Top". The window is designed in XAML and is controled in the class "CameraView" but it does not seem to include a "TopMost" property or equivalent. Attached are the code of "CameraView.xaml.cs" and the code of "CameraView.xaml" that are part of OptiTrack SDK (NaturalPoint) called "Single_Camera_CSharp_.NET_3.0". One could expect the class CameraView to contain properties or members to set the position of the window on the screen or to set it to TopMost but as far as searched I found nothing. I wonder what I should do. Thank you, Brian ================ "CameraView.xaml.cs" using System; using System.IO; using System.Net; using System.Windows; using System.Windows.Controls; using System.Windows.Data; using System.Windows.Media; using System.Windows.Media.Animation; using System.Windows.Navigation; using System.Drawing.Imaging; using System.Drawing.Drawing2D; using System.Windows.Threading; namespace TestProject { public partial class CameraView { private const int NP_OPTION_OBJECT_COLOR_OPTION = 3; private const int NP_OPTION_VIDEO_TYPE = 48; private const int NP_OPTION_NUMERIC_DISPLAY_ON = 71; private const int NP_OPTION_NUMERIC_DISPLAY_OFF = 72; private const int NP_OPTION_FETCH_RLE = 73; private const int NP_OPTION_FETCH_GRAYSCALE = 74; private const int NP_OPTION_FRAME_DECIMATION = 52; private const int NP_OPTION_INTENSITY = 50; private const int NP_OPTION_SEND_EMPTY_FRAMES = 41; private const int NP_OPTION_THRESHOLD = 5; private const int NP_OPTION_EXPOSURE = 46; private const int NP_OPTION_SEND_FRAME_MASK = 73; private const int NP_OPTION_TEXT_OVERLAY_OPTION = 74; // public delegate void OnCameraViewCreate(CameraView camera); // public static OnCameraViewCreate onCameraViewCreate; private System.Drawing.Bitmap raw = new System.Drawing.Bitmap(353, 288, System.Drawing.Imaging.PixelFormat.Format32bppArgb); private int mFrameCounter; private int mDisplayCounter; private DispatcherTimer timer1 = new DispatcherTimer(); private bool mVideoFrameAvailable = false; private int mNumeric = -1; private bool mGreyscale = false; private bool mOverlay = true; public CameraView() { this.InitializeComponent(); timer1.Interval = new TimeSpan(0, 0, 0, 0, 10); timer1.Tick += new EventHandler(timer1_Tick); } public int Numeric { get { return mNumeric; } set { mNumeric = value % 100; if (mNumeric = 0) { if (Camera != null) Camera.SetOption(NP_OPTION_NUMERIC_DISPLAY_ON, value % 100); } } } private bool CameraRunning = false; private OptiTrack.NPCamera mCamera; public OptiTrack.NPCamera Camera { get { return mCamera; } set { if (mCamera == value) return; //== Don't do anything if you're assigning the same camera == if (mCamera != null) { //== Shut the selected camera down ==<< if (CameraRunning) { CameraRunning = false; mCamera.Stop(); mCamera.FrameAvailable -= FrameAvailable; } } mCamera = value; if (mCamera == null) { mNumeric = -1; } else { serialLabel.Content = "Camera "+mCamera.SerialNumber.ToString(); //mNumeric.ToString(); } } } private void FrameAvailable(OptiTrack.NPCamera Camera) { mFrameCounter++; try { OptiTrack.NPCameraFrame frame = Camera.GetFrame(0); int id = frame.Id; if (CameraRunning) { GetFrameData(Camera, frame); } frame.Free(); } catch (Exception) { int r = 0; r++; } } private void GetFrameData(OptiTrack.NPCamera camera, OptiTrack.NPCameraFrame frame) { BitmapData bmData = raw.LockBits(new System.Drawing.Rectangle(0, 0, raw.Width, raw.Height), ImageLockMode.ReadWrite, System.Drawing.Imaging.PixelFormat.Format32bppArgb); int stride = bmData.Stride; System.IntPtr bufferPtr = bmData.Scan0; unsafe { byte* buffer = (byte*)(void*)bufferPtr; camera.GetFrameImage(frame, bmData.Width, bmData.Height, bmData.Stride, 32, ref buffer[0]); } raw.UnlockBits(bmData); mVideoFrameAvailable = true; } private void timer1_Tick(object sender, EventArgs e) { if (CameraRunning && mVideoFrameAvailable) { mVideoFrameAvailable = false; cameraImage.Source = Img(raw); mDisplayCounter++; } } private System.Windows.Media.ImageSource Img(System.Drawing.Bitmap img) { System.Drawing.Imaging.BitmapData bmData = img.LockBits(new System.Drawing.Rectangle(0, 0, img.Width, img.Height), System.Drawing.Imaging.ImageLockMode.ReadWrite, System.Drawing.Imaging.PixelFormat.Format32bppPArgb); System.Windows.Media.Imaging.BitmapSource bitmap = System.Windows.Media.Imaging.BitmapSource.Create( img.Width, img.Height, 96, 96, PixelFormats.Bgra32, System.Windows.Media.Imaging.BitmapPalettes.WebPalette, bmData.Scan0, bmData.Stride * bmData.Height, bmData.Stride); img.UnlockBits(bmData); return bitmap; } private void startStopButton_Click(object sender, RoutedEventArgs e) { if (CameraRunning) StopCamera(); else StartCamera(); } public void StartCamera() { if (Camera != null) { mFrameCounter = 0; mDisplayCounter = 0; Camera.FrameAvailable += FrameAvailable; Camera.SetOption(NP_OPTION_VIDEO_TYPE, 0); Camera.SetOption(NP_OPTION_FRAME_DECIMATION, 1); Camera.SetOption(NP_OPTION_INTENSITY, 0); Camera.SetOption(NP_OPTION_EXPOSURE, 10); Camera.SetOption(NP_OPTION_THRESHOLD, 50); Camera.SetOption(NP_OPTION_OBJECT_COLOR_OPTION, 0); SetOverlayOption(); SetGreyscaleOption(); timer1.Start(); Camera.Start(); CameraRunning = true; this.Numeric = mNumeric; startStopButton.Content = "Stop Camera"; } } private void SetGreyscaleOption() { if(mGreyscale) Camera.SetOption(NP_OPTION_VIDEO_TYPE, 1); else Camera.SetOption(NP_OPTION_VIDEO_TYPE, 0); } private void SetOverlayOption() { if(mOverlay) Camera.SetOption(NP_OPTION_TEXT_OVERLAY_OPTION, 255); else Camera.SetOption(NP_OPTION_TEXT_OVERLAY_OPTION, 0); } public void StopCamera() { if (Camera != null) { Camera.Stop(); timer1.Stop(); CameraRunning = false; Camera.FrameAvailable -= FrameAvailable; Camera.SetOption(NP_OPTION_NUMERIC_DISPLAY_OFF, 0); startStopButton.Content = "Start Camera"; } } private void greyscaleButton_Click(object sender, RoutedEventArgs e) { if(mGreyscale) mGreyscale = false; else mGreyscale = true; SetGreyscaleOption(); } private void OverlayButton_Click(object sender, RoutedEventArgs e) { if(mOverlay) mOverlay = false; else mOverlay = true; SetOverlayOption(); } private void exposureSlider_ValueChanged(object sender, RoutedEventArgs e) { if (mCamera!=null) { mCamera.SetOption(NP_OPTION_EXPOSURE, (int) this.exposureSlider.Value); } } private void thresholdSlider_ValueChanged(object sender, RoutedEventArgs e) { if (mCamera != null) { mCamera.SetOption(NP_OPTION_THRESHOLD, (int)this.thresholdSlider.Value); } } private void optionsButton_Click(object sender, RoutedEventArgs e) { if (!propertyPanel.IsVisible) propertyPanel.Visibility = Visibility.Visible; else propertyPanel.Visibility = Visibility.Collapsed; } } } ================ "CameraView.xaml"

  Read the article

• jQuery .live fireing multiple times!

  - by cstrzelc

  Greetings Guru's, This is a little hard to explain, but I'll give it a shot. I have a quick question regarding to the .live() function in JQuery. I'm going to simplify the example here. I have a page "index.php" that has a container "#display_files_container" which is populated with anchor links that are generated dynamically by a different page "process.php". The links are loaded into that same <div> when those links are selected based on the attributes of that link. See Examples: INDEX.PHP <html> <head><title>index.php</title> <!-- this function below loads process.php and passes it the dirid variable via post. I then use this post variable inside of process.php to pull other links from the database --> <script language="text/javascript"> $('.directory').live("click", function() { $('#display_files_container').load('plugins/project_files/process.php', {dirid: $(this).attr('dirid')}); }); </script> </head> <?php /*This code initial populates the link array so we have the first links populated before the users clicks for the first time*/ some code to fetch the $current_directory_list array from the database initially.... >? <body> <div id='display_files_container'> <?php /*Cycle through the array and echo out all the links which have been pulled from DB*/ for($i=0;$i<$current_directory_count;$i++) { echo "<a href='#' class='directory' dirid='".$current_directory_list[$i]['id']." '>".$current_directory_list[$i]['directory_name']. "</a> "; } ?> </div> </body> </html> PROCESS.PHP this file includes code to populate the $current_directory_list[] array from the database based on the post variable "$_POST['dirid']" that was sent from the .click() method in index.php. It then echo's the results out and we display them in the #display_files_container container. When you click on those links the process repeats. This works..... you can click though the directory tree and it loads the new links every time. However, it seems to want to .load() the process.php file many times over for one click. The number of times process.php is loaded seems to increase the more the links are clicked. So for example you can click on a link and firebug reports that process.php was loaded 23 times..... Eventually I would imagine I would record a stackoverflow. Please let me know if you have any ideas. Are there any ways that I can assure that .live() loads the process.php file only once? Thanks, -cs

  Read the article

• Append <ul> and <li> in recursive loop

  - by Batman

  I have a site collection. I was told I need a recursive loop to do this. This is what I've tried: When the site loads, call getSiteTree() which passes the top level website to my getSubSite() function. From there I check if there are any subsites. I have a boolean but I'm not really using it for anything yet, I've just seen it used before for this type of work. Anyways, from there I check if there are any sub sits, if not I log the end of the branch, if there are, I call the function again using the new url and repeat the process. Looking at my console, it seems to work as intended. function getSiteTree(){ var tree = $('#treeviewList'); var rootsite = window.location.protocol + "//" + window.location.hostname; var siteEnd = false; getSubSite(rootsite); } function getSubSite(url){ $().SPServices({ operation: "GetWebCollection", webURL: url, async: true, completefunc: function(xData, Status) { var siteUrl; var siteCount = $(xData.responseXML).find("Web").length; if(siteCount == 0){ console.log("end of branch"); siteEnd = true; }else{ $(xData.responseXML).find("Web").each(function() { siteUrl = $(this).attr("Url"); console.log(siteUrl); getSubSite(siteUrl); }); } } }); } My questions: now that I have my sites, I need to take those sites and create something like this but I'm not sure how to accomplish this. <li>Site 1 <ul> <li>sub 1.1</li> <li>sub 1.2</li> <li>sub 1.3</li> <ul> <li>1.3.1</li> </ul> <li>sub 1.4</li> <li>sub 1.5</li> </ul> </li> <li>Site 2 <ul> <li>sub 2.1</li> <li>sub 2.2</li> <li>sub 2.3</li> <ul> <li>2.3.1</li> <li>2.3.2</li> </ul> </ul> </li> </ul> I have this inital html: <div id="treeviewDiv" style="width:200px;height:150px;overflow:scroll"> <ui id="treeviewList"></ui> </div>

  Read the article

• What container type provides better (average) performance than std::map?

  - by Truncheon

  In the following example a std::map structure is filled with 26 values from A - Z (for key) and 0 - 26 for value. The time taken (on my system) to lookup the last entry (10000000 times) is roughly 250 ms for the vector, and 125 ms for the map. (I compiled using release mode, with O3 option turned on for g++ 4.4) But if for some odd reason I wanted better performance than the std::map, what data structures and functions would I need to consider using? I apologize if the answer seems obvious to you, but I haven't had much experience in the performance critical aspects of C++ programming. UPDATE: This example is rather trivial and hides the true complexity of what I'm trying to achieve. My real world project is a simple scripting language that uses a parser, data tree, and interpreter (instead of a VM stack system). I need to use some kind of data structure (perhaps map) to store the variables names created by script programmers. These are likely to be pretty randomly named, so I need a lookup method that can quickly find a particular key within a (probably) fairly large list of names. #include <ctime> #include <map> #include <vector> #include <iostream> struct mystruct { char key; int value; mystruct(char k = 0, int v = 0) : key(k), value(v) { } }; int find(const std::vector<mystruct>& ref, char key) { for (std::vector<mystruct>::const_iterator i = ref.begin(); i != ref.end(); ++i) if (i->key == key) return i->value; return -1; } int main() { std::map<char, int> mymap; std::vector<mystruct> myvec; for (int i = 'a'; i < 'a' + 26; ++i) { mymap[i] = i - 'a'; myvec.push_back(mystruct(i, i - 'a')); } int pre = clock(); for (int i = 0; i < 10000000; ++i) { find(myvec, 'z'); } std::cout << "linear scan: milli " << clock() - pre << "\n"; pre = clock(); for (int i = 0; i < 10000000; ++i) { mymap['z']; } std::cout << "map scan: milli " << clock() - pre << "\n"; return 0; }

  Read the article

• MVC SiteMap - when different nodes point to same action SiteMap.CurrentNode does not map to the correct route

  - by awrigley

  Setup: I am using ASP.NET MVC 4, with mvcSiteMapProvider to manage my menus. I have a custom menu builder that evaluates whether a node is on the current branch (ie, if the SiteMap.CurrentNode is either the CurrentNode or the CurrentNode is nested under it). The code is included below, but essentially checks the url of each node and compares it with the url of the currentnode, up through the currentnodes "family tree". The CurrentBranch is used by my custom menu builder to add a class that highlights menu items on the CurrentBranch. The Problem: My custom menu works fine, but I have found that the mvcSiteMapProvider does not seem to evaluate the url of the CurrentNode in a consistent manner: When two nodes point to the same action and are distinguished only by a parameter of the action, SiteMap.CurrentNode does not seem to use the correct route (it ignores the distinguishing parameter and defaults to the first route that that maps to the action defined in the node). Example of the Problem: In an app I have Members. A Member has a MemberStatus field that can be "Unprocessed", "Active" or "Inactive". To change the MemberStatus, I have a ProcessMemberController in an Area called Admin. The processing is done using the Process action on the ProcessMemberController. My mvcSiteMap has two nodes that BOTH map to the Process action. The only difference between them is the alternate parameter (such are my client's domain semantics), that in one case has a value of "Processed" and in the other "Unprocessed": Nodes: <mvcSiteMapNode title="Process" area="Admin" controller="ProcessMembers" action="Process" alternate="Unprocessed" /> <mvcSiteMapNode title="Change Status" area="Admin" controller="ProcessMembers" action="Process" alternate="Processed" /> Routes: The corresponding routes to these two nodes are (again, the only thing that distinguishes them is the value of the alternate parameter): context.MapRoute( "Process_New_Members", "Admin/Unprocessed/Process/{MemberId}", new { controller = "ProcessMembers", action = "Process", alternate="Unprocessed", MemberId = UrlParameter.Optional } ); context.MapRoute( "Change_Status_Old_Members", "Admin/Members/Status/Change/{MemberId}", new { controller = "ProcessMembers", action = "Process", alternate="Processed", MemberId = UrlParameter.Optional } ); What works: The Html.ActionLink helper uses the routes and produces the urls I expect: @Html.ActionLink("Process", MVC.Admin.ProcessMembers.Process(item.MemberId, "Unprocessed") // Output (alternate="Unprocessed" and item.MemberId = 12): Admin/Unprocessed/Process/12 @Html.ActionLink("Status", MVC.Admin.ProcessMembers.Process(item.MemberId, "Processed") // Output (alternate="Processed" and item.MemberId = 23): Admin/Members/Status/Change/23 In both cases the output is correct and as I expect. What doesn't work: Let's say my request involves the second option, ie, /Admin/Members/Status/Change/47, corresponding to alternate = "Processed" and a MemberId of 47. Debugging my static CurrentBranch property (see below), I find that SiteMap.CurrentNode shows: PreviousSibling: null Provider: {MvcSiteMapProvider.DefaultSiteMapProvider} ReadOnly: false ResourceKey: "" Roles: Count = 0 RootNode: {Home} Title: "Process" Url: "/Admin/Unprocessed/Process/47" Ie, for a request url of /Admin/Members/Status/Change/47, SiteMap.CurrentNode.Url evaluates to /Admin/Unprocessed/Process/47. Ie, it is ignorning the alternate parameter and using the wrong route. CurrentBranch Static Property: /// <summary> /// ReadOnly. Gets the Branch of the Site Map that holds the SiteMap.CurrentNode /// </summary> public static List<SiteMapNode> CurrentBranch { get { List<SiteMapNode> currentBranch = null; if (currentBranch == null) { SiteMapNode cn = SiteMap.CurrentNode; SiteMapNode n = cn; List<SiteMapNode> ln = new List<SiteMapNode>(); if (cn != null) { while (n != null && n.Url != SiteMap.RootNode.Url) { // I don't need to check for n.ParentNode == null // because cn != null && n != SiteMap.RootNode ln.Add(n); n = n.ParentNode; } // the while loop excludes the root node, so add it here // I could add n, that should now be equal to SiteMap.RootNode, but this is clearer ln.Add(SiteMap.RootNode); // The nodes were added in reverse order, from the CurrentNode up, so reverse them. ln.Reverse(); } currentBranch = ln; } return currentBranch; } } The Question: What am I doing wrong? The routes are interpreted by Html.ActionLlink as I expect, but are not evaluated by SiteMap.CurrentNode as I expect. In other words, in evaluating my routes, SiteMap.CurrentNode ignores the distinguishing alternate parameter.

  Read the article

• Business rule validation of hierarchical list of objects ASP.NET MVC

  - by SergeanT

  I have a list of objects that are organized in a tree using a Depth property: public class Quota { [Range(0, int.MaxValue, ErrorMessage = "Please enter an amount above zero.")] public int Amount { get; set; } public int Depth { get; set; } [Required] [RegularExpression("^[a-zA-Z]+$")] public string Origin { get; set; } // ... another properties with validation attributes } For data example (amount - origin) 100 originA 200 originB 50 originC 150 originD the model data looks like: IList<Quota> model = new List<Quota>(); model.Add(new Quota{ Amount = 100, Depth = 0, Origin = "originA"); model.Add(new Quota{ Amount = 200, Depth = 0, Origin = "originB"); model.Add(new Quota{ Amount = 50, Depth = 1, Origin = "originC"); model.Add(new Quota{ Amount = 150, Depth = 1, Orinig = "originD"); Editing of the list Then I use Editing a variable length list, ASP.NET MVC 2-style to raise editing of the list. Controller actions QuotaController.cs: public class QuotaController : Controller { // // GET: /Quota/EditList public ActionResult EditList() { IList<Quota> model = // ... assigments as in example above; return View(viewModel); } // // POST: /Quota/EditList [HttpPost] public ActionResult EditList(IList<Quota> quotas) { if (ModelState.IsValid) { // ... save logic return RedirectToAction("Details"); } return View(quotas); // Redisplay the form with errors } // ... other controller actions } View EditList.aspx: <%@ Page Title="" Language="C#" ... Inherits="System.Web.Mvc.ViewPage<IList<Quota>>" %> ... <h2>Edit Quotas</h2> <%=Html.ValidationSummary("Fix errors:") %> <% using (Html.BeginForm()) { foreach (var quota in Model) { Html.RenderPartial("QuotaEditorRow", quota); } %> <% } %> ... Partial View QuotaEditorRow.ascx: <%@ Control Language="C#" Inherits="System.Web.Mvc.ViewUserControl<Quota>" %> <div class="quotas" style="margin-left: <%=Model.Depth*45 %>px"> <% using (Html.BeginCollectionItem("Quotas")) { %> <%=Html.HiddenFor(m=>m.Id) %> <%=Html.HiddenFor(m=>m.Depth) %> <%=Html.TextBoxFor(m=>m.Amount, new {@class = "number", size = 5})%> <%=Html.ValidationMessageFor(m=>m.Amount) %> Origin: <%=Html.TextBoxFor(m=>m.Origin)%> <%=Html.ValidationMessageFor(m=>m.Origin) %> ... <% } %> </div> Business rule validation How do I implement validation of business rule: Amount of quota and sum of amounts of nested quotas should equal (e.a. 200 = 50 + 150 in example)? I want to appropriate inputs Html.TextBoxFor(m=>m.Amount) be highlighted red if the rule is broken for it. In example if user enters not 200, but 201 - it should be red on submit. Using sever validation only. Thanks a lot for any advise.

  Read the article

• Segmentation fault in my C program

  - by user233542

  I don't understand why this would give me a seg fault. Any ideas? This is the function that returns the signal to stop the program (plus the other function that is called within this): double bisect(double A0,double A1,double Sol[N],double tol,double c) { double Amid,shot; while (A1-A0 > tol) { Amid = 0.5*(A0+A1); shot = shoot(Sol, Amid, c); if (shot==2.*Pi) { return Amid; } if (shot > 2.*Pi){ A1 = Amid; } else if (shot < 2.*Pi){ A0 = Amid; } } return 0.5*(A1+A0); } double shoot(double Sol[N],double A,double c) { int i,j; /*Initial Conditions*/ for (i=0;i<buff;i++) { Sol[i] = 0.; } for (i=buff+l;i<N;i++) { Sol[i] = 2.*Pi; } Sol[buff]= 0; Sol[buff+1]= A*exp(sqrt(1+3*c)*dx); for (i=buff+2;i<buff+l;i++) { Sol[i] = (dx*dx)*( sin(Sol[i-1]) + c*sin(3.*(Sol[i-1])) ) - Sol[i-2] + 2.*Sol[i-1]; } return Sol[i-1]; } The values buff, l, N are defined using a #define statement. l = 401, buff = 50, N = 2000 Here is the full code: #include <stdio.h> #include <stdlib.h> #include <math.h> #define w 10 /*characteristic width of a soliton*/ #define dx 0.05 /*distance between lattice sites*/ #define s (2*w)/dx /*size of soliton shape*/ #define l (int)(s+1) /*array length for soliton*/ #define N (int)2000 /*length of field array--lattice sites*/ #define Pi (double)4*atan(1) #define buff (int)50 double shoot(double Sol[N],double A,double c); double bisect(double A0,double A1,double Sol[N],double tol,double c); void super_pos(double antiSol[N],double Sol[N],double phi[][N]); void vel_ver(double phi[][N],double v,double c,int tsteps,double dt); int main(int argc, char **argv) { double c,Sol[N],antiSol[N],A,A0,A1,tol,v,dt; int tsteps,i; FILE *fp1,*fp2,*fp3; fp1 = fopen("soliton.dat","w"); fp2 = fopen("final-phi.dat","w"); fp3 = fopen("energy.dat","w"); printf("Please input the number of time steps:"); scanf("%d",&tsteps); printf("Also, enter the time step size:"); scanf("%lf",&dt); do{ printf("Please input the parameter c in the interval [-1/3,1]:"); scanf("%lf",&c);} while(c < (-1./3.) || c > 1.); printf("Please input the inital speed of eiter soliton:"); scanf("%lf",&v); double phi[tsteps+1][N]; tol = 0.0000001; A0 = 0.; A1 = 2.*Pi; A = bisect(A0,A1,Sol,tol,c); shoot(Sol,A,c); for (i=0;i<N;i++) { fprintf(fp1,"%d\t",i); fprintf(fp1,"%lf\n",Sol[i]); } fclose(fp1); super_pos(antiSol,Sol,phi); /*vel_ver(phi,v,c,tsteps,dt); for (i=0;i<N;i++){ fprintf(fp2,"%d\t",i); fprintf(fp2,"%lf\n",phi[tsteps][i]); }*/ } double shoot(double Sol[N],double A,double c) { int i,j; /*Initial Conditions*/ for (i=0;i<buff;i++) { Sol[i] = 0.; } for (i=buff+l;i<N;i++) { Sol[i] = 2.*Pi; } Sol[buff]= 0; Sol[buff+1]= A*exp(sqrt(1+3*c)*dx); for (i=buff+2;i<buff+l;i++) { Sol[i] = (dx*dx)*( sin(Sol[i-1]) + c*sin(3.*(Sol[i-1])) ) - Sol[i-2] + 2.*Sol[i-1]; } return Sol[i-1]; } double bisect(double A0,double A1,double Sol[N],double tol,double c) { double Amid,shot; while (A1-A0 > tol) { Amid = 0.5*(A0+A1); shot = shoot(Sol, Amid, c); if (shot==2.*Pi) { return Amid; } if (shot > 2.*Pi){ A1 = Amid; } else if (shot < 2.*Pi){ A0 = Amid; } } return 0.5*(A1+A0); } void super_pos(double antiSol[N],double Sol[N],double phi[][N]) { int i; /*for (i=0;i<N;i++) { phi[i]=0; } for (i=buffer+s;i<1950-s;i++) { phi[i]=2*Pi; }*/ for (i=0;i<N;i++) { antiSol[i] = Sol[N-i]; } /*for (i=0;i<s+1;i++) { phi[buffer+j] = Sol[j]; phi[1549+j] = antiSol[j]; }*/ for (i=0;i<N;i++) { phi[0][i] = antiSol[i] + Sol[i] - 2.*Pi; } } /* This funciton will set the 2nd input array to the derivative at the time t, for all points x in the lattice */ void deriv2(double phi[][N],double DphiDx2[][N],int t) { //double SolDer2[s+1]; int x; for (x=0;x<N;x++) { DphiDx2[t][x] = (phi[buff+x+1][t] + phi[buff+x-1][t] - 2.*phi[x][t])/(dx*dx); } /*for (i=0;i<N;i++) { ptr[i] = &SolDer2[i]; }*/ //return DphiDx2[x]; } void vel_ver(double phi[][N],double v,double c,int tsteps,double dt) { int t,x; double d1,d2,dp,DphiDx1[tsteps+1][N],DphiDx2[tsteps+1][N],dpdt[tsteps+1][N],p[tsteps+1][N]; for (t=0;t<tsteps;t++){ if (t==0){ for (x=0;x<N;x++){//inital conditions deriv2(phi,DphiDx2,t); dpdt[t][x] = DphiDx2[t][x] - sin(phi[t][x]) - sin(3.*phi[t][x]); DphiDx1[t][x] = (phi[t][x+1] - phi[t][x])/dx; p[t][x] = -v*DphiDx1[t][x]; } } for (x=0;x<N;x++){//velocity-verlet phi[t+1][x] = phi[t][x] + dt*p[t][x] + (dt*dt/2)*dpdt[t][x]; p[t+1][x] = p[t][x] + (dt/2)*dpdt[t][x]; deriv2(phi,DphiDx2,t+1); dpdt[t][x] = DphiDx2[t][x] - sin(phi[t+1][x]) - sin(3.*phi[t+1][x]); p[t+1][x] += (dt/2)*dpdt[t+1][x]; } } } So, this really isn't due to my overwriting the end of the Sol array. I've commented out both functions that I suspected of causing the problem (bisect or shoot) and inserted a print function. Two things happen. When I have code like below: double A,Pi,B,c; c=0; Pi = 4.*atan(1.); A = Pi; B = 1./4.; printf("%lf",B); B = shoot(Sol,A,c); printf("%lf",B); I get a segfault from the function, shoot. However, if I take away the shoot function so that I have: double A,Pi,B,c; c=0; Pi = 4.*atan(1.); A = Pi; B = 1./4.; printf("%lf",B); it gives me a segfault at the printf... Why!?

  Read the article

• Please Critique this PHP Login Script

  - by NightMICU

  Greetings, A site I developed was recently compromised, most likely by a brute force or Rainbow Table attack. The original log-in script did not have a SALT, passwords were stored in MD5. Below is an updated script, complete with SALT and IP address banning. In addition, it will send a Mayday email & SMS and disable the account should the same IP address or account attempt 4 failed log-ins. Please look it over and let me know what could be improved, what is missing, and what is just plain strange. Many thanks! <?php //Start session session_start(); //Include DB config include $_SERVER['DOCUMENT_ROOT'] . '/includes/pdo_conn.inc.php'; //Error message array $errmsg_arr = array(); $errflag = false; //Function to sanitize values received from the form. Prevents SQL injection function clean($str) { $str = @trim($str); if(get_magic_quotes_gpc()) { $str = stripslashes($str); } return $str; } //Define a SALT, the one here is for demo define('SALT', '63Yf5QNA'); //Sanitize the POST values $login = clean($_POST['login']); $password = clean($_POST['password']); //Encrypt password $encryptedPassword = md5(SALT . $password); //Input Validations //Obtain IP address and check for past failed attempts $ip_address = $_SERVER['REMOTE_ADDR']; $checkIPBan = $db->prepare("SELECT COUNT(*) FROM ip_ban WHERE ipAddr = ? OR login = ?"); $checkIPBan->execute(array($ip_address, $login)); $numAttempts = $checkIPBan->fetchColumn(); //If there are 4 failed attempts, send back to login and temporarily ban IP address if ($numAttempts == 1) { $getTotalAttempts = $db->prepare("SELECT attempts FROM ip_ban WHERE ipAddr = ? OR login = ?"); $getTotalAttempts->execute(array($ip_address, $login)); $totalAttempts = $getTotalAttempts->fetch(); $totalAttempts = $totalAttempts['attempts']; if ($totalAttempts >= 4) { //Send Mayday SMS $to = "[email protected]"; $subject = "Banned Account - $login"; $mailheaders = 'From: [email protected]' . "\r\n"; $mailheaders .= 'Reply-To: [email protected]' . "\r\n"; $mailheaders .= 'MIME-Version: 1.0' . "\r\n"; $mailheaders .= 'Content-type: text/html; charset=iso-8859-1' . "\r\n"; $msg = "<p>IP Address - " . $ip_address . ", Username - " . $login . "</p>"; mail($to, $subject, $msg, $mailheaders); $setAccountBan = $db->query("UPDATE ip_ban SET isBanned = 1 WHERE ipAddr = '$ip_address'"); $setAccountBan->execute(); $errmsg_arr[] = 'Too Many Login Attempts'; $errflag = true; } } if($login == '') { $errmsg_arr[] = 'Login ID missing'; $errflag = true; } if($password == '') { $errmsg_arr[] = 'Password missing'; $errflag = true; } //If there are input validations, redirect back to the login form if($errflag) { $_SESSION['ERRMSG_ARR'] = $errmsg_arr; session_write_close(); header('Location: http://somewhere.com/login.php'); exit(); } //Query database $loginSQL = $db->prepare("SELECT password FROM user_control WHERE username = ?"); $loginSQL->execute(array($login)); $loginResult = $loginSQL->fetch(); //Compare passwords if($loginResult['password'] == $encryptedPassword) { //Login Successful session_regenerate_id(); //Collect details about user and assign session details $getMemDetails = $db->prepare("SELECT * FROM user_control WHERE username = ?"); $getMemDetails->execute(array($login)); $member = $getMemDetails->fetch(); $_SESSION['SESS_MEMBER_ID'] = $member['user_id']; $_SESSION['SESS_USERNAME'] = $member['username']; $_SESSION['SESS_FIRST_NAME'] = $member['name_f']; $_SESSION['SESS_LAST_NAME'] = $member['name_l']; $_SESSION['SESS_STATUS'] = $member['status']; $_SESSION['SESS_LEVEL'] = $member['level']; //Get Last Login $_SESSION['SESS_LAST_LOGIN'] = $member['lastLogin']; //Set Last Login info $updateLog = $db->prepare("UPDATE user_control SET lastLogin = DATE_ADD(NOW(), INTERVAL 1 HOUR), ip_addr = ? WHERE user_id = ?"); $updateLog->execute(array($ip_address, $member['user_id'])); session_write_close(); //If there are past failed log-in attempts, delete old entries if ($numAttempts > 0) { //Past failed log-ins from this IP address. Delete old entries $deleteIPBan = $db->prepare("DELETE FROM ip_ban WHERE ipAddr = ?"); $deleteIPBan->execute(array($ip_address)); } if ($member['level'] != "3" || $member['status'] == "Suspended") { header("location: http://somewhere.com"); } else { header('Location: http://somewhere.com'); } exit(); } else { //Login failed. Add IP address and other details to ban table if ($numAttempts < 1) { //Add a new entry to IP Ban table $addBanEntry = $db->prepare("INSERT INTO ip_ban (ipAddr, login, attempts) VALUES (?,?,?)"); $addBanEntry->execute(array($ip_address, $login, 1)); } else { //increment Attempts count $updateBanEntry = $db->prepare("UPDATE ip_ban SET ipAddr = ?, login = ?, attempts = attempts+1 WHERE ipAddr = ? OR login = ?"); $updateBanEntry->execute(array($ip_address, $login, $ip_address, $login)); } header('Location: http://somewhere.com/login.php'); exit(); } ?>

  Read the article

• Moving a Drupal between linux servers, best practice to avoid file-ownership problems

  - by zero

  I want to port over a Drupal commons 6x24 from a local LAMP-stack to a production webserver. Both systems run OpenSuse Linux. How do I do this, what are the most important steps. How should I handle file-ownership. It's important for me to have to have full control of the file ownership. If I use the wwwrun account, I frequently run into problems, due to a very strict webserver-admin. See for example the long history of looking for fixes and solutions see this thread and even more interesting see this very long and impressive thread here. All troubles I run into have to do with file-owernship and permissions. This is my current setup; Note: This was just a quick hacked installation - quick and dirty. Well my interest is after the general options i have in the port of a drupal from linux to linux linux-vi17:/srv/www/htdocs/com624 # ls -l insgesamt 224 -rwxrwxrwx 1 root www 45285 19. Jan 00:54 CHANGELOG.txt -rwxrwxrwx 1 root www 925 19. Jan 00:54 COPYRIGHT.txt -rwxrwxrwx 1 root www 206 19. Jan 00:54 cron.php drwxrwxrwx 2 root www 4096 19. Jan 00:54 includes -rwxrwxrwx 1 root www 923 19. Jan 00:54 index.php -rwxrwxrwx 1 root www 1244 19. Jan 00:54 INSTALL.mysql.txt -rwxrwxrwx 1 root www 1011 19. Jan 00:54 INSTALL.pgsql.txt -rwxrwxrwx 1 root www 47073 19. Jan 00:54 install.php -rwxrwxrwx 1 root www 15572 19. Jan 00:54 INSTALL.txt -rwxrwxrwx 1 root www 14940 19. Jan 00:54 LICENSE.txt -rwxrwxrwx 1 root www 1858 19. Jan 00:54 MAINTAINERS.txt drwxrwxrwx 3 root www 4096 19. Jan 00:54 misc drwxrwxrwx 35 root www 4096 19. Jan 00:54 modules drwxrwxrwx 4 root www 4096 19. Jan 00:54 profiles -rwxrwxrwx 1 root www 1470 19. Jan 00:54 robots.txt drwxrwxrwx 2 root www 4096 19. Jan 00:54 scripts drwxrwxrwx 4 root www 4096 19. Jan 00:54 sites drwxrwxrwx 7 root www 4096 19. Jan 00:54 themes -rwxrwxrwx 1 root www 26250 19. Jan 00:54 update.php -rwxrwxrwx 1 root www 4864 19. Jan 00:54 UPGRADE.txt -rwxrwxrwx 1 root www 294 19. Jan 00:54 xmlrpc.php linux-vi17:/srv/www/htdocs/com624 # thx to BetaRides answer here a quick overview on the drush functionality with rsync http://drush.ws/ core-rsync Rsync the Drupal tree to/from another server using ssh. Examples: drush rsync @dev @stage Rsync Drupal root from dev to stage (one of which must be local). drush rsync ./ @stage:%files/img Rsync all files in the current directory to the 'img' directory in the file storage folder on stage. Arguments: source May be rsync path or site alias. See rsync documentation and example.aliases.drushrc.php. destination May be rsync path or site alias. See rsync documentation and example.aliases.drushrc.php. Options: --mode The unary flags to pass to rsync; --mode=rultz implies rsync -rultz. Default is -az. --RSYNC-FLAG Most rsync flags passed to drush sync will be passed on to rsync. See rsync documentation. --exclude-conf Excludes settings.php from being rsynced. Default. --include-conf Allow settings.php to be rsynced --exclude-files Exclude the files directory. --exclude-sites Exclude all directories in "sites/" except for "sites/all". --exclude-other-sites Exclude all directories in "sites/" except for "sites/all" and the site directory for the site being synced. Note: if the site directory is different between the source and destination, use --exclude-sites followed by "drush rsync @from:%site @to:%site" --exclude-paths List of paths to exclude, seperated by : (Unix-based systems) or ; (Windows). --include-paths List of paths to include, seperated by : (Unix-based systems) or ; (Windows). Topics: docs-aliases Site aliases overview with examples Aliases: rsync

  Read the article

• My server app works strangely. What could be the reason(s)?

  - by Poni

  Hi! I've written a server app (two parts actually; proxy server and a game server) using C++ (board game). It uses IOCP as the sockets interface. For that app I've also written a "client simulator" (hereafter "client") app that spawns many client connections, where each of them plays, in very high speed, getting the CPU to be 100% utilized. So, that's how it goes in terms of topology: Game server - holds the game state. Real players do not connect it directly but through the proxy server. When a player joins a game, the proxy actually asks for it on behalf of that player, and the game server spawns a "player instance" for that player, and from now on, every notification between the game server and the player is being passed through the proxy. Proxy server - holds TCP connections with the real players. Players communicate with the game server through it only. Client simulator - connects to the proxy only. When running the server (again, it's actually two server apps) & client locally it all works just fine. I'm talking about 40k+ player instances in which all of them are active in a game. On the other hand, when running the server remotely with, say, 1000 clients who play things getting strange. For example, I run it as said above. Then with Task Manager I kill the client simulator app ("End Process Tree"). Then it seems like the buffer of the remote server got modified by another thread, or in other words, a memory corruption has been occurred. The server crashes because it got an unknown message id (it's a custom protocol where each message has it's own unique number). To make things clear, here is how I run the apps: PC1 - game server and clients simulator (because the clients will connect the proxy). PC2 - proxy server. The strangest thing is this: Only the remote side gets "corrupted". Remote in terms that it's not the PC I use to code the app (VC++ 2008). Let's call the PC I use to code the apps "PC1". Now for example, if this time I ran the game server on PC1 (it means that proxy server on PC2 and clients simulator on PC1), then the proxy server crashes with an "unknown message id" error. Another variation is when I run the proxy server on PC1 (again, the dev machine), the game server and the clients simulator on PC2, then the game server on PC2 gets crashed. As for the IOCP config: The servers' internal connections use the default receive/send buffer sizes. Tried even with setting them to 1MB, but no luck. I have three PCs in total; 2 x Vista 64bit <<-- one of those is the dev machine. The other is connected through WiFi. 1 x WinXP 32bit They're all connected in a "full duplex" manner. What could be the reason? Tried about everything; Stack tracing, recording some actions (like read/write logging).. I want to stress that only the PC I'm not using to code the apps crashes (actually the server app "role" which is running on it - sometimes the game server and sometimes the proxy server). At first I thought that maybe the wireless PC has problems (it's wireless..) but: TCP has it's own mechanisms to make sure the packet is delivered properly. Also, a crash also happens when trying it with the two PCs that are physically connected (Vista vs. XP). Another option is that the Windows DLLs versions might have problems, but then again, one of the tests is Vista vs. Vista, and the other is Vista vs. XP. Any idea?

  Read the article

< Previous Page | 199 200 201 202 203 204 205 206 207 208 209 210  | Next Page >