Search Results

Search found 6392 results on 256 pages for 'reduce duplicate'.

Page 203/256 | < Previous Page | 199 200 201 202 203 204 205 206 207 208 209 210  | Next Page >

• Shared printer hosted by Windows 7 to XP peers [closed]

  - by Alistair Knock

  Possible Duplicate: Add Network Printer drivers in Windows 7/Server 2008 R2? A Canon Pixma ip4600 installed all by itself when connected to a Windows 7-64 bit machine. I then updated it with the add-on Canon provide to give additional functionality. I then wish to share it with a box which is running Windows XP 32-bit. The XP box can see the printer but can't find a driver from the 7 machine, which is fine. I ask the 7 machine to get the x86 drivers, but it can't. I install the 32-bit XP drivers on the XP machine, but unlike previous Canon drivers (which unzip to give an .inf file), they assume a local printer and partially give up. I find the .inf file in the Program files\CanonBJ\... directory. Neither the XP machine, nor the 7 machine when the CanonBJ directory is shared to it, is happy with the .inf file. I attempt to install the 32-bit drivers on the 64-bit 7 machine, which, understandably, fail. Where do we go from here? (I apologise for posting in the first-person, I'm not sure why this was)

  Read the article

• Video output vanishes and it isn't the video card... suggestions?

  - by Ira Baxter

  I have a high-end dual processor Dell workstation that operated for several years without problem. Recently, the video output has gone flaky, in the sense that after 2-3 days, it loses synch with the monitor (sometimes you can still see a hashed-mess of the what you expect to see on the screen). Poking at the keyboard, and accessing the file system on the machine from over the network, indicates that the machine is running fine and its just the video. A reboot fixes the problem... for another day or two. This in effect makes the machine unusable. So, I replaced the video card with an exact duplicate bought from e-bay. (I checked after the dupe arrived to be sure, yep, same model number). I still get the same behavior. So unless I believe that both video cards are broken the same way, I have to beleive this is a problem with the motherboard/power supply, neither of which I am inclined to replace. The only other possibility I can think of is a Windows update to the graphics driver. How would I check for this? Anybody had a similar problem? Otherwise we're junking what used to be a perfectly good machine. (Another couple of hours of more wasted effort and that's it in terms of economics anyway).

  Read the article

• Should be simple: existing laptop with local user and outlook 2007 migrate on same computer to domain user with outlook 2007 emails intact

  - by bifpowell

  I have Dell Laptop with windows 7 64 bit and for the last year it's been just a machine with an account like: machine\john there are files in folders and stuff in c:\users\john and john uses outlook 2007 as a pop3 client and has identifiable local appdata pst files. Now I installed a server and want to have everything be domain-centric so I added this laptop to the domain with admin credentials and then logged in as a domain user as: domain\john.smith Now I want to duplicate machine\john (outlook emails mostly) to domain\john.smith. In the past I used the Files and Settings Xfer Wizard and done. I tried that here and it crunched away for a while, made the file, but the restore had no effect - it ran for a while, had a progress bar, but it's like nothing happened at all afterwards. I've rebooted the machine, logged in as domain administrator as the first user to log on after the restart and tried: c:\users\john xcopy c:\users\john c:\users\john.smith /V /C /F /H /K /Y /E ...and it copies some of it, but when it gets to c:\users\john.smith\appdata\local\application data it chokes "Access denied, unable to create directory" I also tried logging in as domain\john.smith and copying the entire directory that the PSTs are in from machine\john and a lot of the mail was there when I launched outlook after replacing the PSTs, but not all of them??? I got errors about files in use when doing this method, which I figure must be why not all the old emails are in the inbox?... There must be some extremely simple way to do what must be a very common requirement. Any guidance appreciated.

  Read the article

• Looking for suitable backup solution Mac OS X to offsite Centos 6 server 1TB of working data

  - by Brady

  I'll start by saying what we have in place currently: On site file server (Mac OS X Server) that is used by GFX designers and they have a working 1TB of data. Offsite server with 2TB available storage (Centos 6) Mac OS X server rsync data to offsite server every 6 hours (rsync -avz --delete --progress -e ssh ...) Mac OS X server does full data backup to LTO 4 tape on a 10 day recycle (Mon-Fri for 2 weeks) rsync pushes about 60GB of file changes a day. The problem: The onsite tape backup is failing as 1TB of graphics files don't compress well to fit onto a 800GB LTO4 tape. Backup is incredibly slow doing a full backup. Pain in the backside getting people to remember to change the tape. Often gets forgotten etc The quick solution: Buy LTO5 Drive and tapes. However this has been turned down because of the cost... What I would like: Something that works in the same way rysnc works. Only changed data is sent over the wire and can be scheduled to run multiple times during the day. Data that is sent is compressed and sent over SSH. Something that keeps a 14day retention but doesn't keep duplicate data So as an example if I have 1TB of working data and 60GB of changes are made each day then I expect around 1.84TB of data to be stored on the offsite server. To work with the Mac OS X server and Centos 6 server. Not cost an arm and a leg. Must be a cheaper solution than buying an LTO5 drive with tapes (around £1500). Be able to be setup to run autonomously. Have some sort of control panel that will allow an admin to easily restore a file/folder. Any recommendations?

  Read the article

• Starting my own server - basic recommendations and questions [closed]

  - by Ilia Rostovtsev

  Possible Duplicate: Can you help me with my capacity planning? I'm planning to start my own high-performance server and then use collocation services for keeping it up and running. I'm planning to USE it for processing videos and keeping big video site up! (using FFMpeg, MENcoder and etc.) I just need recommendations on whether listed hardware is good enough and will work together well and fast enough. Do I need anything else (missed something). I remember about CPU coolers though! ;) I'm planning to use SSD drives so please tell me if it's going to work just as regular HDDs (but much faster)? Are they going to be used as RAID (is this possible for SSDs)? Here is what I would like to get: Intel ® Server System SR1600URHSR (Urbanna) or Intel® Server System SR1695WBAC 2 x Intel Xeon X5650 4 x 16Gb DDR-III 1333MHz Kingston ECC Reg (KVR13R9D4/16) 3 x (or maybe 4x) 480Gb SSD Intel 520 Series (SSDSC2CW480A3K5) Which server system would be better? Is listed hardware new/good enough and worth buying it at the moment? Should I probably take a look at something slightly more expensive but more up to date and powerful, may be? After all as software I would like to use CentOS 6 64 bit + WHM/CPanel? Any other suggestions on maybe cheaper and same/more powerful server management system but WHM? What most important points to keep in mind when starting/maintaining your own server?

  Read the article

• Problem with Windows Service and network printers.

  - by Mohammadreza

  I have a Windows Service application that every now and then should print some documents. As far as I know, to print those documents, my service must be run with a user account other than Local Service or Network Service. So i have created a user account and added that to the Administrators group and ran the service with it. With locally installed printers, I don't have any problems because those printers are automatically installed for all accounts. To be able to print with the network printers, I have created another application that syncs the installed printers of the currently logged in user with the user account that my service uses with the rundll32.exe printui.dll,PrintUIEntry command. In Vista and Windows7 I don't have any problems with the syncing of the printers because every time that a printer should be installed the authentication window will open and it asks for the appropriate user account to install that printer (The service user account is not created on the network printers computers) but in XP a find dialog with the "Connecting to {printername}" caption will appear and stops responding, or sometimes it installs the printer but every time service tries to print, a Win32Exception with "A StartDocPrinter call was not issued" message will throw and in the user account that runs the sync application a duplicate printer will be shown and I couldn't delete those printers unless with force (using registry). Am I doing the right thing for printing documents with Windows Services at all? If yes, how can I solve the above-mentioned problem? And if not, what the heck should I do? Thanks.

  Read the article

• Windows server 2008R2 routing with single NIC

  - by Fabian

  I'm trying to duplicate a Linux server configuration to a windows server 2008R2 box. Basicaly this linux server acts as a router, but it is doing its job with only 1 interface (1 NIC). Here is the network configuration in place (I cannot change it) : INTERNET <== Router (local ip = 194.168.0.3) <== linux Server (ip : 194.168.0.2). The router is configured with a DMZ to 194.168.0.2, and only allow this IP to connect to internet (Cannot change this router configuration). The linux server is configured with a default gateway to 194.168.0.3, with the option : "Act as router". All other computer on the lan have this configuration (given by DHCP) : IP range : 194.168.0.X MASK : 255.255.255.0 Default gateway : 194.168.0.2 And everything is working perfectly. I'm trying to reproduce this way of routing with only one NIC from a windows server 2008R2, but it seems that you cannnot do it with only one NIC (all exemples I see are refering to 2 NIC with 2 different network). Does someone have an idea how to achieved this in Windows server 2008R2 ? Tx you for your help ! Fabian.

  Read the article

• Symbolic Links Between User Accounts

  - by Pez Cuckow

  I have been using a cron job to duplicate a folder into another users account every day and someone suggested using symbolic links instead although I cannot get them to work. In summary user GAMER generates log files that they want to access via HTTP, however I only have a web-server in the user account SERVER, in the past I would copy the logs folder from GAMERS account into SERVER/public_html/. and then chmod the files so the server could access them. Trying to use symbolic links I set up a link from root (as only root can access both accounts) I used: ln -s /home/GAMER/game/logs/ /home/SERVER/public_html/logs However it seems that only root can use this link, I tried chmoding the link, all the files in the gamers /game/logs/*, /game/logs itself to 777 as well as changing chown and chgrp to server the files still cannot be read. When viewed from servers account my shell shows the link and where it is to hi-lighted in black with red text. Am I doing something wrong? Please enlighten me! /home/GAMER/game/ (chmod & chgrp) drwxrwxrwx 3 SERVER SERVER 4096 2011-01-07 15:46 logs /home/SERVER/public_html (chmod -h & chgrp -h) lrwxrwxrwx 1 server server 41 2011-01-07 19:53 logs -> /home/GAMER/game/logs/

  Read the article

• How to reinstall Windows Boot Manager on EFI partition

  - by joaocandre

  So I've been trying to install Ubuntu on a second HDD on my desktop, which has W8 installed on a SSD (UEFI-only boot). Thing is, during Ubuntu installation I made the mistake of choosing to install the bootloader (GRUB) to the first disk (the SSD), and after install I could not boot into W8 (the entries in GRUB didn't work). Following these instructions, I managed to be able to get "Windows Boot Manager" back, however I lost GRUB in the process, and got a duplicate "Windows Boot Manager" entry in BIOS, along with the "Ubuntu" entry, which then I used to boot into Ubuntu. Later, I decided to reinstall Ubuntu, and formatted the HDD from within windows, however, the entries in BIOS stayed the same, and, while I had the HDD connected to the motherboard, I could not boot into an Ubuntu Live USB (in order to reinstall Ubuntu). I made another mistake by updating the BIOS, which cleared all of the EFI boot entries in BIOS, and, right now, I get an error when boot from the SSD: grub: device not found (...) So it seems that grub is still installed in the EFI partition of the SSD, and since I don't have the WBM entry in BIOS anymore, I cannot even boot into Windows, and the previous instructions don't work anymore. Is there another way to reset W8 EFI partition to the default?

  Read the article

• lighttpd with multiple IPs, each with a UCC certificate and many hostnames

  - by Dave

  I'd like to get lighttpd working with UCC certificates, but I can't seem to figure out the correct syntax. Essentially, for each IP address, I have one UCC certificate and a bunch of hostnames. $SERVER["socket"] == "10.0.0.1:443" { ssl.engine = "enable" ssl.ca-file = "/etc/ssl/certs/the.ca.cert.pem" ssl.pemfile = "/etc/ssl/private/websitegroup1.com.pem" $HTTP["host"] =~ "mywebsite.com" { server.document-root = /var/www/mywebsite.com/htdocs" } The above code works fine for one hostname, but as soon as I try to set up another hostname (note the same SSL cert): $SERVER["socket"] == "10.0.0.1:443" { ssl.engine = "enable" ssl.ca-file = "/etc/ssl/certs/the.ca.cert.pem" ssl.pemfile = "/etc/ssl/private/websitegroup1.com.pem" $HTTP["host"] =~ "anotherwebsite.com" { server.document-root = /var/www/anotherwebsite.com/htdocs" } ...I get this error: Duplicate config variable in conditional 6 global/SERVERsocket==10.0.0.1:443: ssl.engine Is there any way I can put a conditional so that only if ssl.engine is not already enabled, enable it? Or do I have to put all my $HTTP["host"]s inside the same $SERVER["socket"] (which will make config file management more difficult for me) or is there some entirely different way to do it? This has to be repeated for multiple IPs too (so I'll have a bunch of SERVER["socket"] == 10.0.0.2:443" etc), each with one UCC cert and many hostnames. Am I going about this the wrong way entirely? My goal is to conserve IP addresses when I have many websites that are related and can share an SSL certificate, but still need their own SSL-accessible version from the appropriate hostname (instead of a single secure.mywebsite.com).

  Read the article

• LVM and cloning HDs

  - by jcea

  Using Linux, I have several backup levels. One of them is a periodical sector by sector copy (using dd) of my laptop harddisk to an external USB disk. Yes, I have other backups too, like remote rsync. This approach (the disk dd) is OK when cloning a HDD with no LVM volumes, since I can plug the external disk anytime and mount the partitions simply mounting /dev/sdb* instead of /dev/sda*. Trivial and handy. Today I moved ALL my harddisk (including the /boot) to LVM. Everything works fine. I will stress it for a couple of days, and then I will do a sector by sector copy to my external harddisk. Now I have a problem, I guess. If in the future I plug the external USB HDD to recover any file, the OS will detect a duplicate LVM configuration, with the same name and the same UUID. Even doing a vgrename (which LVM would be renamed, the internal HDD or the external HDD?), the cloned UUID will not change. Is there any command to change name and UUID? Ideally I would clone the HDD and then change the LVM group name and its UUID, but I don't know how to do it. Another related issue would be... In the past I have booted my laptop using the external disk, using the BIOS boot menu and changing GRUB entries manually to boot from /dev/sdb instead of /dev/sda. But now my current GRUB configuration boots directly from a LVM logical volume, something like: set root='(LVM-root)' in my grub.cfg. So... What is going to happen with duplicated volumes? Any suggestion? I guess I could repartition my external harddisk and change backup strategy from dd to rsync, but this disk has windows installed too, and I really would like to have a physical "real" copy.

  Read the article

• Burn .srt subtitles to AVC encoded video (transcoding with hardsubs) [closed]

  - by Saxtus

  Possible Duplicate: How do I hard code a movie with subtitles? I am looking for a software (or combination of software) that will allow me to hard burn subtitles from an .srt file, that has italics and bold typefaces, to an H.264/AVC encoded video so it can played from a desktop player that can't display external subtitles correctly. Ideally it could use Directshow as input as DirectVobSub makes nice job showing the subtitles as they should (allowing me to globally adjust font and size). CUDA use, to speed up encoding, will be great but not necessary. Video source is also H.264/AVC encoded. Audio is AC-3 5.1 and should be retained too but I have no problem re-muxin it later as long as it keeps synced. Until now I've unsuccessfully tested: Avisynth 2.58 Unable to make Direcvobsub to launch through it TextSub() command renders subtitles with fixed font/size and doesn't decode tags Malformed audio TMPGEnc 4.0 XPress 4.7.4.299 Audio downmixed to 2.0 Importing of subtitles doesn't decode tags Badaboom 1.2.1.7 No importing of subtitles at all SUPER © 2010.build.37 "Directshow decode" has similar effect as Avisynth above Other modes doesn't appear to allow any subtitles in Thank you.

  Read the article

• Resize Win2003 system+boot partitions to bigger disks & different controller?

  - by ane

  Have an old Win2003 server with 1 SCSI hard drive partitioned as follows: D: boot (includes D:\ntldr, boot.ini, etc.) C: system (includes C:\WINDOWS) Want to move the whole system to new hardware with bigger drives and different controllers. Specifically, C: to a 300GB SAS drive, and D: to a 2TB SATA drive. Tried: VMWare Converter - VMWare Server - Diskpart Result: Diskpart refuses to resize system or boot disks VMWare Converter - VMWare Server - GParted Result: Will not boot (see http://serverfault.com/questions/219868/resize-ntfs-system-partitions-with-gparted ) Attach original VMWare disk to a duplicate VMWare install - Diskpart Result: Will not boot (goes to Directory Services Restore mode) Backup Exec System Recovery Server Edition 2010 with Restore Anywhere (tried restoring both to VMWare and to the bare system, without VMWare) Result: Windows Boot error: Could not read from the selected boot disk. Check boot path. Supposedly this is a boot.ini problem, so I try bootcfg /rebuild from the recovery console. Says it can't find windows partition so it can't rebuild. Thought about Ghost but it's completely different hardware/controllers that we're restoring to, so I doubt it would boot. Reinstalling Windows from scratch is not an option due to critical custom software heavily embedded on the original machine. Has anyone been in a similar situation (with unusual boot/system partitions) before and figured out how to resize onto different disks?

  Read the article

• Routing subnet over GRE tunnel

  - by eMgz

  Hi, Im trying to configure a GRE over IPSec connection between two subnets. The IPSec tunnel is opened and now I want to add a GRE tunnel over it: ip tunnel add GRE01 mode gre remote 10.244.0.1 local 10.244.245.32 ttl 255 ip link set GRE01 up ip addr add 10.244.248.126 dev GRE01 ip route add 10.244.248.125 dev GRE01 Now I have an interface GRE01 (ifconfig): GRE10 Link encap:UNSPEC HWaddr <h_addr> inet addr:10.244.248.126 P-t-P:10.244.248.126 Mask:255.255.255.255 UP POINTOPOINT RUNNING NOARP MTU:1476 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) And the following routes (ip route list): 10.244.248.125 dev GRE10 scope link <pub_subnet> dev eth0 proto kernel scope link src <pub_ip> default via <pub_gw> dev eth0 metric 100 As a last step, I need now to route my subnet over the tunnel: ip route add 10.245.1.224/28 10.244.248.125 However, I am getting the error Error: either "to" is duplicate, or "10.244.248.125" is a garbage. So, what I didn't understand is why I can't route my subnet over the tunnel, once the only route I have there says that it should route the tunnel IP over the GRE01 interface. Any hint? Thanks.

  Read the article

• Prevent nginx from redirecting traffic from https to http when used as a reverse proxy

  - by Chris Pratt

  Here's my abbreviated nginx vhost conf: upstream gunicorn { server 127.0.0.1:8080 fail_timeout=0; } server { listen 80; listen 443 ssl; server_name domain.com ~^.+\.domain\.com$; location / { try_files $uri @proxy; } location @proxy { proxy_pass_header Server; proxy_redirect off; proxy_set_header Host $http_host; proxy_set_header X-Forwarded-For $proxy_add_x_forwarded_for; proxy_set_header X-Forwarded-Proto https; proxy_set_header X-Real-IP $remote_addr; proxy_set_header X-Scheme $scheme; proxy_connect_timeout 10; proxy_read_timeout 120; proxy_pass http://gunicorn; } } The same server needs to serve both HTTP and HTTPS, however, when the upstream issues a redirect (for instance, after a form is processed), all HTTPS requests are redirected to HTTP. The only thing I have found that will correct this issue is changing proxy_redirect to the following: proxy_redirect http:// https://; That works wonderfully for requests coming from HTTPS, but if a redirect is issued over HTTP it also redirects that to HTTPS, which is a problem. Out of desperation, I tried: if ($scheme = 'https') { proxy_redirect http:// https://; } But nginx complains that proxy_redirect isn't allowed here. The only other option I can think of is to define the two servers separately and set proxy_redirect only on the SSL one, but then I would have duplicate the rest of the conf (there's a lot in the server directive that I omitted for simplicity sake). I know I could also use an include directive to factor out the redundancy, but I really want to keep just one conf file without any dependencies. So, first, is there something I'm missing that will negate the problem entirely? Or, second, if not, is there any other way (besides including an external file) to factor out the redundant config information so that I can separate out the HTTP and HTTPS versions of the server config?

  Read the article

• My system administrator set up 2 databases that sync. Master-Master. However, these two databases a

  - by Alex

  DB1 and DB2. I made changes to DB1, and it does not seem to be on DB2. When I do "SHOW SLAVE STATUS\G" on DB2, there seems to be an error: mysql> show slave status\G *************************** 1. row *************************** Slave_IO_State: Waiting for master to send event Master_Host: Master_User: Master_Port: Connect_Retry: 60 Master_Log_File: mysql-bin.0005496 Read_Master_Log_Pos: 5445649315 Relay_Log_File: mysqld-relay-bin.0041705 Relay_Log_Pos: 1624302119 Relay_Master_Log_File: mysql-bin.0004461 Slave_IO_Running: Yes Slave_SQL_Running: No Replicate_Do_DB: Replicate_Ignore_DB: Replicate_Do_Table: Replicate_Ignore_Table: Replicate_Wild_Do_Table: Replicate_Wild_Ignore_Table: Last_Errno: 1062 Last_Error: Error 'Duplicate entry '4779' for key 1' on query. Default database: 'falc'. Query: 'INSERT INTO `log` (`anon_id`, `created_at`, `query`, `episode_url`, `detail_id`, `ip`) VALUES ('fdzn1d45kMavF4qbyePv', '2009-11-19 04:19:13', 'amazon', '', '', '130.126.40.57')' Skip_Counter: 0 Exec_Master_Log_Pos: 162301982 Relay_Log_Space: 136505187184 Until_Condition: None Until_Log_File: Until_Log_Pos: 0 Master_SSL_Allowed: No Master_SSL_CA_File: Master_SSL_CA_Path: Master_SSL_Cert: Master_SSL_Cipher: Master_SSL_Key: Seconds_Behind_Master: NULL 1 row in set (0.00 sec) Then, I did show tables, and it seems like DB2 is lacking a table that I created on DB1...that means that for some reason, DB2 stopped syncing with DB1. How can I simply allow them to be in full synchronization again? All I want is DB2 to be exactly the same as DB1!

  Read the article

• SQL Server 2008 R2 Error 15401 when trying to add a domain user

  - by Alice

  I am trying to add a domain user. I am doing the following. Expand Security Right click on Logins Select New Login... Login name select search Click on location and select entire directory Type username Click checkname The name goes underlined and add some more info Click OK Click OK I then get the following error: I have found http://support.microsoft.com/kb/324321. The Login does exist There is no Duplicate security identifiers Authentication failure I don't think is happening as I can browse AD Case sensitivity should not be the problem as I am doing the checkname and it is correcting it. Not a Local account Name resolution again I can see the AD I have rebooted the server (VM) and the issue is still happening. Any ideas? Edit I have also: Domain member: Digitally encrypt secure channel data (when possible) – Disable this policy Domain member: Digitally sign secure channel data (when possible) – Disable this policy Rebooted server http://talksql.blogspot.com/2009/10/windows-nt-user-or-group-domainuser-not.html Edit 2 I have also: Digitally encrypt or sign secure channel data (always)- Disabled Rebooted Edit 3 Since the question have moved site I no longer haves access to comment etc... I have checked the dns on the server to a machine where it is working. The DNS servers are the same on both...

  Read the article

• Should tripwire be entering /proc?

  - by dsadinoff

  When initializing the db with tripwire --init it spat out a bunch of errors pertaining to /proc: ### Warning: File system error. ### Filename: /proc/16982/fd/4 ### No such file or directory ### Continuing... ### Warning: File system error. ### Filename: /proc/16982/fdinfo/4 ### No such file or directory ### Continuing... ### Warning: File system error. ### Filename: /proc/16982/task/16982/fd/4 ### No such file or directory ### Continuing... ### Warning: File system error. ### Filename: /proc/16982/task/16982/fdinfo/4 ### No such file or directory ### Continuing... ### Warning: Duplicate object encountered. ### /proc/sys/net/ipv6/neigh This feels like noise. The twpol.txt file has the following clause: # # Critical devices # ( rulename = "Devices & Kernel information", severity = $(SIG_HI), ) { /dev -> $(Device) ; /proc -> $(Device) ; } Which, if I understand it right, is going to cause tripwire to care deeply about the entire contents of /proc. Shouldn't it just care about the static parts of /proc like the drivers and such, and not the per-pid stuff? Why does it ship like this?

  Read the article

• Live Screencast under Linux

  - by OmnipotentEntity

  I was having some difficulty with running a Live Screencast under Linux. I've found jtvlc and tried using that, but whenever I use it the stream comes out either blank or lagged with extremely high latency. I have a fast internet connection and a fast computer, but am I perhaps taxing it too much? Any ideas on what I could possibly be doing wrong? # 1. Get an account on http://www.justin.tv/ # 2. Copy streaming key from: http://www.justin.tv/broadcast/adv_other # 2. Install VLC: http://www.videolan.org/vlc/ # 3. Get Win/Mac/Lin Stream Client: \ # http://apiwiki.justin.tv/mediawiki/index.php/Linux_Broadcasting_API # 4. Adjust the vlc parameters to your liking and run VLC like this #!/bin/bash cvlc screen:// --input-slave=pulse:// \ --screen-width 1920 \ --screen-height 1080 \ --screen-fps 5 \ -v input_stream \ --sout='#duplicate{ dst="transcode{ scale=1, venc=x264{ keyint=60 }, vcodec=h264, vb=600, acodec=mp4a, ab=32, channels=2, samplerate=22050 } :rtp{dst=127.0.0.1,port=1234,sdp=file:///tmp/vlc.sdp} "}' \ --sout-transcode-threads=4 & sleep 2 # 5. Run JTVLC to stream like this: ./jtvlc/jtvlc omnipotententity censored /tmp/vlc.sdp # Notes: #- If you want to see what you're about to stream add 'dst=display, ' # before 'dst="transcode[' # More about the VLC parameters: http://wiki.videolan.org/Documentation:Modules/screen

  Read the article

• How can i export a folder of Firefox Bookmarks into a text file

  - by Memor-X

  I want to clean up my bookmark folders by getting rid of duplicated/links. i have created a program which will import 2 text files which contains a URL like this File 1: http://www.google/com http://anime.stackexchange.com/ https://www.fanfiction.net/guidelines/ https://www.fanfiction.net/anime/Magical-Girl-Lyrical-Nanoha/?&srt=1&g1=2&lan=1&r=103&s=2 File 2: http://scifi.stackexchange.com/ http://scifi.stackexchange.com/questions/56142/why-didnt-dumbledore-just-hunt-voldemort-down http://anime.stackexchange.com/ http://scifi.stackexchange.com/questions/5650/how-can-the-doctor-be-poisoned the program compares the 2 lists and creates a single master list with duplicate URLs removed. Now i have a few Backup bookmark folders in Firefox which on occasion i'll bookmark all tabs into a new folder with the date of the backup before i close off tabs or do reset my PC. each folder can have between 1000-2000 bookmarks, sometimes there are a bunch of pages which keep getting bookmarked, ie, i have ~50 pages on the Magical Girl Lyrical Nanoha Wiki on different spells, character and terminology which i commonly look back on. I'd like to know how i can export a bookmark folder so i have a list of URLs similar to what i use in my program

  Read the article

• Saving a file in a CSV type in Excel always removes the BOM

  - by rickp

  I've been trying to find a reasonable solution/explanation (unsuccessfully) to find out why Excel defaults to removing the BOM when saving a file to the CSV type. Please forgive me if you find this a duplicate of this question. This handles reading CSV files with non-ASCII encoding, but it doesn't cover saving the file back out (which is where the biggest issue lies). Here is my current situation (which I'm going to gather is common among localized software dealing with Unicode characters and a CSV format): We export data to a CSV format using UTF-16LE, ensuring the BOM is set (0xFFFE). We validate after the file is generated with a Hex editor to ensure it was set correctly. Open the file in Excel (for this example we're exporting Japanese characters) and witness that Excel handles loading the file with the correct encoding. Attempts to save this file will prompt you with a warning message indicating that the file may contain features that may not be compatible with Unicode encoding, but asks if you'd like to save anyway. If you select the Save As dialog, it will immediately ask you to save the file as "Unicode Text" rather than CSV. If you select the "CSV" extension and save the file it removes the BOM (obviously along with all the Japanese characters). Why would this happen? Is there a solution to this problem, or is this a known 'bug'/limitation of Excel? Additionally (as a side issue) it appears that Excel, when loading UTF-16LE encoded CSV files, only uses TAB delimiters. Again, is this another known 'bug'/limitation of Excel?

  Read the article

• Cloning a NAS drive which hosts a SQL Server DB

  - by Adrian Hand

  We have a system in the field running a server application which is suffering with major performance issues. The system in question has 2 onboard 300gb sas drives in RAID 5 from which it boots Windows Server 2003, and a 6tb buffalo terastation NAS unit (also RAID 5) to which the server app does all of its reading and writing. I believe the terastation is the source of all our woes. Whilst under load, reads and writes tick by at something of the order of 1meg/sec, though the network in question is hardly utilised. The terastation contains various data, but crucially hosts a full instance worth of SQL Server .mdf and .ldf files (master etc - the whole shooting match) I wish to stop all the services on the server, then take everything on the terastation and essentially clone it to some alternative onboard storage, so as to eliminate the terastation from the equation as far as poor performance is concerned. ie the terastation is currently drive D: - I want to copy everything off and then have the duplicate assume the drive letter so that as far as the software is aware, nothing is different. This is tricky because of the mdf and ldf files - everything else will work with a straight up file copy. Can anyone suggest a means to achieve what I am describing? Many thanks!

  Read the article

• Why does Windows XP (during a rename operation) report file already exists when it doesn't?

  - by Hawk

  From the command-line: E:\menu\html\tom\val\.svn\tmp\text-base>ver Microsoft Windows [Version 5.2.3790] E:\menu\html\tom\val\.svn\tmp\text-base>dir Volume in drive E is DATA Volume Serial Number is F047-F44B Directory of E:\menu\html\tom\val\.svn\tmp\text-base 12/23/2010 04:36 PM <DIR> . 12/23/2010 04:36 PM <DIR> .. 12/23/2010 04:01 PM 0 wtf.com3.csv.svn-base 1 File(s) 0 bytes 2 Dir(s) 170,780,262,400 bytes free E:\menu\html\tom\val\.svn\tmp\text-base>rename wtf.com3.csv.svn-base com3.csv.svn-base A duplicate file name exists, or the file cannot be found. E:\menu\html\tom\val\.svn\tmp\text-base>dir Volume in drive E is DATA Volume Serial Number is F047-F44B Directory of E:\menu\html\tom\val\.svn\tmp\text-base 12/23/2010 04:36 PM <DIR> . 12/23/2010 04:36 PM <DIR> .. 12/23/2010 04:01 PM 0 wtf.com3.csv.svn-base 1 File(s) 0 bytes 2 Dir(s) 170,753,064,960 bytes free E:\menu\html\tom\val\.svn\tmp\text-base>` I don't know what to do about this, as there is no other file in this directory. Why does Windows XP report that there is already a file here named com3.csv.svn-base when there is clearly no other file here?

  Read the article

• Connecting a laptop to a TV via HDMI

  - by Madmartigan

  I just bought a new Dell XPS17 laptop (Win7) that only has HDMI output. My last 2 laptops had VGA, which I used to connect to my Sony Bravia 32" TV with no issues, but with the HDMI it's been quite a headache. Drivers for display adapters have been updated to the latest versions: Intel(R) HD Graphics Family NVIDIA GeForce GT 550M I went to a store and plugged in to 4 different TVs from different manufacturers. A sales rep and I spent about 30 minutes being baffled by the results (which are the same as my current TV): Extreme buggy behavior in the Nvidia and Windows display/resolution control panel Can not extend or duplicate displays, can only select one Third and fourth output devices "randomly" detected by the Windows control panel Could not get the screen to fit the output (edges cut off on all sides by about a half inch) Resolution and colors less than perfect. Artifacts around text. Display "randomly" cuts out Defaults to TV output only when plugged in Can not change resolution on either device when connected No audio from the TV Plugged in to 3 monitors from different manufacturers: Defaults to duplicated displays when plugged in Everything works perfectly So far, four people have gone through all the settings in the latop with no luck. I had similar, but not exactly matching results with a different laptop. I'm using the Sony Bravia currently at home, but in order to get it to work I have to turn on the laptop, wait until the display shows up on it, close the lid, then cycle through each output channel on the TV until I come back around to the HDMI port again, but still I have the symptoms described above. However: Once in a while, it just works. Sometimes, seemingly randomly, the output fits the screen perfectly. Sometimes the audio comes through the speakers too, but not always. Usually my screen saver "Mystify" will come up with a message that it cannot be displayed due to a limitation of the video card, but then sometimes it works fine. These 3 things seem to be independent of each other and don't always happen together. So, is there any way to get the laptop to output correctly to a TV, or is it just not meant to be?

  Read the article

• E-mail duplication problem

  - by Gavin Osborn

  I have taken out a hosting agreement with a well respected hosting provider for a couple of internet facing servers. We have deployed several applications to these servers which send various e-mails back to us for reporting purposes. Context: Each server runs Windows Server 2003 R2 with the IIS 6.0 SMTP service installed. Each application is configured to use the local instance of IIS to send e-mails. The external IP address of each server is mapped to a particular domain eg: server1.mydomain.com server2.mydomain.com These e-mails are sent from a company domain name and not the domain name of the hosted servers (eg: [email protected]) Symptoms: A small number (<1%) of e-mails sent from these applications appear to be duplicated. These are exact duplicate in terms of both content and message headers. The Fix: I contacted my hosting provider and they told me this was a common problem & instructed me to: Change the HELO response of your mail server service to a FQDN (server1.mydomain.com && server2.mydomain.com) Create a DNS A record that resolves the FQDN of your mail server to the primary IP address of your sending mail server. Create a PTR record that resolves your primary IP address back to your mail server's FQDN In the sending domain's (mycompanydomain.com) DNS zone file, add the appropriate SPF record for your hosted servers. eg: v=spf1 a mx include:mydomain -all The Problem Continues: I made all of the changes as prescribed above, I was a little hesitant because these steps seemed to suggest they were more for stopping your messages getting blocked than they were for stopping them from being duplicated - but I am certainly no expert in these matters. It has been 5 days since I applied this fix and the problem still persists. I am certain that these problems are not a bug in the software because they are 4 different applications installed on 2 different servers, all of whom are exhibiting this strange behaviour. This behaviour has also not been seen in our UAT environment. Were my hosts correct to suggest this fix? If not, does anyone know what could be the cause of this problem? Many Thanks

  Read the article

< Previous Page | 199 200 201 202 203 204 205 206 207 208 209 210  | Next Page >