Search Results

Search found 61544 results on 2462 pages for 'drive error'.

Page 205/2462 | < Previous Page | 201 202 203 204 205 206 207 208 209 210 211 212  | Next Page >

• Help understanding my hard drive / partitioning situation... Pictures Included! :)

  - by xopenex

  So I have installed windows 7, and two different distros of linux... I have read and tried to understand things like "spanned" "extended" "primary" "swap" "dev/dev2/" "GRUB" "Windows Boot Loader/Manager" etc.... I have a very very limited understanding of all of it! :) I am trying to figure out how to get all OS boot options on one Boot manager (I'm thinking it will be GRUB), because at this point when i turn on my computer, I basically get two booting options (excluding the memtest options etc)... One options is to boot one of my Linux Distros and the second option is to boot my Windows 7. When i go with the first option, Linux boots up... when i go with the second Windows 7 option, I get the "windows boot manager screen" and I can choose Windows 7 or my other installation of Linux (Ubuntu)... In addition, I did not have swap partition from my first installation of Linux, I created it during the installation of my second distro... This is a lot of info for me, but I'm guessing that you linux Gurus, pretty much understand what is going on! Hope my question makes sense.. i will try and simplify... Can i get all 3 OS's optioned to boot from one GRUB? Can i get both Linux distros to use one swap file (I have seen this possible in other threads, but because of how my disk is partitioned, i dont know if i can do this) I hope that i dont have to start all over installing one after the other. Ive got some pics that may help understand my hard drive situation! Thanks guys! :) EDIT... i had some pics, but im a new member.. so cant post them... :( here is a description of the pics... incase i can email them or post later. [grub][3] First Screen I come to after turning on computer... "Ubuntu with linux 3.2.6" (highlighted) fires up Linux perfectly... other choice at bottom of list "Windows 7 (loader) (on dev/sda1)... brings me to the next picture below.. windows boot manager [win boot mngr][6] both options here load the os selected [Disk Manager Windows][1] picture of my hard drive situation through windows disk manager utility [gparted][2] picture of my hard drive situation through "gparted" [mycomp][4] picture of my hard drive situation through "my computer" [paragon][5] one last pic of my hard drive situation through the eyes of "paragon"

  Read the article

• Error when updating enumerated value?

  - by igrad

  Once upon a time, there was a Player class (simplified version) enum animState{RUNNING,JUMPING,FALLING,IDLING}; class Player { public: Player(int x, int y); void handle(); void show(); ~Player(); private: int m_x; int m_y; animState playerAnimState; } There was also a "handle" function-member, which took care of all movement and collisions for the player: #include "player.h" void Player::handle() { if(/*Player presses 'D' key*/) { m_x++; playerAnimState = RUNNING; } //Other stuff that is just there to look nice Through lots of experimentation with "//" and "/**/", I've found that I consistently get an error at "playerAnimState = RUNNING." Have I broken some enumeration rule? Does my laptop really suck that bad? I hate to post a "fix my code for me" question, but I'm not very seasoned with enums.

  Read the article

• Authentication error when trying to upgrade from 11.10 to 12.04

  - by mahmuodmasri

  I wrote : ~$ do-release-upgrade and the system says: Checking for a new ubuntu release Get:1 Upgrade tool signature [198 B] Get:2 Upgrade tool [1551 kB] Fetched 1551 kB in 6s (167 kB/s) extracting 'precise.tar.gz' authenticate 'precise.tar.gz' against 'precise.tar.gz.gpg' exception from gpg: GnuPG exited non-zero, with code 2 Debug information: gpg: Signature made Thu 11 Oct 2012 07:47:10 AM EET using DSA key ID 437D05B5 gpg: can't open `/etc/apt/trusted.gpg' gpg: keydb_search failed: file open error gpg: Can't check signature: public key not found Authentication failed Authenticating the upgrade failed. There may be a problem with the network or with the server. Please help me!

  Read the article

• Error Setting Java Environment Variables

  - by Cherie Riesberg

  Problem:  Not exactly SharePoint, but the issue is when setting the %JAVA_HOME% environment variable, Java installs to the Program Files directory by default.  The space in the path seems to stop the variable from being read.  You get an error. Solution:  Change Program Files to Progra~1, so the path now looks like this: C:\Progra~1\Java\jdk1.6.0_23\bin\; You can type %JAVA_HOME%\bin\javac to test.  Output should look like this: Usage: javac <options> <source files> where possible options include: ...

  Read the article

• Android app, No error message but has stopped unexpectedly [migrated]

  - by user74722

  Does anyone know what is my problem. I do not have any compile error messages however when i run the app it crashes and stops unexpectedly. Here is my codes. Thank you in advance. ListView l ; @Override protected void onCreate(Bundle savedInstanceState) { super.onCreate(savedInstanceState); setContentView(R.layout.activity_final_project); String arr[]={"Red","Green","Blue","Yellow","Cyan"}; l=(ListView) findViewById(R.id.listView1); ArrayAdapter<String> adapter=new ArrayAdapter<String>(getApplicationContext(), android.R.layout.simple_list_item_1, arr); l.setAdapter(adapter); Button buttonOne = (Button) findViewById(R.id.button1); buttonOne.setOnClickListener(new OnClickListener(){ @Override public void onClick(View v){ setContentView(R.layout.layout_save); // setContentView(R.layout.activity_final_project); //startActivity(new Intent("com.example.finalproject.layout_save")); } }); }

  Read the article

• Can't boot after disk error 12.10

  - by user1189907

  Lately, I've been having Ubuntu crashing randomly.. it goes into read only mode, but once I restart it's working again. Today it happened again and I had to manually shut the computer down. Now I'm not able to boot anymore. I get the following when turning the computer on: error: unknown filesystem And I'm left at "grub rescue". I booted from the Live CD and installed "boot-repair". When I run it it says "no os has been found on this computer", it gives me no option to carry out any fixes. Boot Repair generated the following output which shows some errors: http://paste.ubuntu.com/1348224/ Any idea on how to fix this?

  Read the article

• WCF REST POST error bad request 400

  - by lyatcomit

  Here's my code: DOAMIN: using System; using System.Collections; using System.Runtime.Serialization; namespace Comit.TrafficService.Services.Mobile { [DataContract(Namespace = "http://192.168.0.161:9999/TrafficService/Domain/Mobile")] public class Error { [DataMember] public int Id { get; set; } [DataMember] public DateTime Time { get; set; } public string Message { get; set; } [DataMember] public string Stacktrace { get; set; } [DataMember] public string Os { get; set; } [DataMember] public string Resolution { get; set; } } } CONTRACT: using System.ServiceModel; using System.ServiceModel.Web; using Comit.TrafficService.Services.Mobile; namespace Comit.TrafficService.Services.Contracts { [ServiceContract(Name = "MobileErrorService")] public interface IMobileError { /// <summary> /// ??????????? /// </summary> /// <param name="Error">??????</param> /// <returns></returns> [OperationContract] [WebInvoke(Method = "POST", BodyStyle = WebMessageBodyStyle.WrappedResponse, UriTemplate = "ErrorReport", RequestFormat = WebMessageFormat.Xml, ResponseFormat = WebMessageFormat.Xml) ] int ErrorReport(Error error); } } SERVICE: using System.ServiceModel.Web; using Comit.TrafficService.Services.Contracts; using Comit.TrafficService.Dao.Mobile; using System; using Comit.TrafficService.Services.Mobile; namespace Comit.TrafficService.Services { public class MobileErrorService : IMobileError { public int ErrorReport(Error error) { return HandleAdd(error); } public int HandleAdd(Error error) { Console.WriteLine("?????error.Message:" + error.Message); ErrorDao edao = new ErrorDao(); Console.WriteLine("??error" ); int result = (int)edao.Add(error); return result; } } } Configuration: <?xml version="1.0" encoding="utf-8" ?> <configuration> <system.serviceModel> <services> <service name="Comit.TrafficService.Services.MobileErrorService"> <host> <baseAddresses> <add baseAddress="http://192.168.0.161:9999"/> </baseAddresses> </host> <endpoint address="http://192.168.0.161:9999/Comit/TrafficService/Services" binding="webHttpBinding" contract="Comit.TrafficService.Services.Contracts.IMobileError" behaviorConfiguration="RestfulBehavior" name="webHttpBinding"> </endpoint> </service> </services> <behaviors> <endpointBehaviors> <behavior name="RestfulBehavior"> <webHttp/> <dataContractSerializer ignoreExtensionDataObject="true"/> </behavior> </endpointBehaviors> </behaviors> </system.serviceModel> </configuration> Host: using System; using System.Collections.Generic; using System.Linq; using System.ServiceModel; using System.Text; using Comit.TrafficService.Services; namespace ServiceTest { class Program { static void Main(string[] args) { using (ServiceHost host = new ServiceHost(typeof(MobileErrorService))) { host.Opened += delegate { Console.WriteLine("CalculaorService????,????????!"); }; host.Open(); Console.Read(); } } } } Client code: using System; using System.ServiceModel; using System.ServiceModel.Description; using TestWCFRest.WcfServices.Services; using System.Net; namespace TestWCFRest.WcfServices.Hosting { class Program { static void Main(string[] args) { //using (ServiceHost host = new ServiceHost(typeof(CalculatorService))) //{ // host.Opened += delegate // { // Console.WriteLine("CalculaorService????,????????!"); // }; // host.Open(); // Console.Read(); //} HttpWebRequest req = null; HttpWebResponse res = null; try { string url = "http://192.168.0.161:9999/Comit/TrafficService/Services/ErrorReport"; req = (HttpWebRequest)WebRequest.Create(url); req.Method = "POST"; req.ContentType = "application/xml; charset=utf-8"; req.Timeout = 30000; req.Headers.Add("SOAPAction", url); System.Xml.XmlDocument xmlDoc = new System.Xml.XmlDocument(); xmlDoc.XmlResolver = null; xmlDoc.Load(@"d:\test.xml"); string sXML = xmlDoc.InnerXml; req.ContentLength = sXML.Length; System.IO.StreamWriter sw = new System.IO.StreamWriter(req.GetRequestStream()); sw.Write(sXML); sw.Close(); res = (HttpWebResponse)req.GetResponse(); } catch (Exception ex) { System.Console.WriteLine(ex.Message); } } } } It's my first time I'm trying to do somethinf with WCF so I don't know how to solve this problem. Since there is a lot of professionals here, I would appreciate your help in solving this. Thank you in advance!

  Read the article

• trying to override getView in a SimpleCursorAdapter gives NullPointerException

  - by Dimitry Hristov

  Would very much appreciate any help or hint on were to go next. I'm trying to change the content of a row in ListView programmatically. In one row there are 3 TextView and a ProgressBar. I want to animate the ProgressBar if the 'result' column of the current row is zero. After reading some tutorials and docs, I came to the conclusion that LayoutInflater has to be used and getView() - overriden. Maybe I am wrong on this. If I return row = inflater.inflate(R.layout.row, null); from the function, it gives NullPointerException. Here is the code: private final class mySimpleCursorAdapter extends SimpleCursorAdapter { private Cursor localCursor; private Context localContext; public mySimpleCursorAdapter(Context context, int layout, Cursor c, String[] from, int[] to) { super(context, layout, c, from, to); this.localCursor = c; this.localContext = context; } /** * 1. ListView asks adapter "give me a view" (getView) for each item of the list * 2. A new View is returned and displayed */ public View getView(int position, View convertView, ViewGroup parent) { View row = super.getView(position, convertView, parent); LayoutInflater inflater = (LayoutInflater)localContext.getSystemService(Context.LAYOUT_INFLATER_SERVICE); String result = localCursor.getString(2); int resInt = Integer.parseInt(result); Log.d(TAG, "row " + row); // if 'result' column form the TABLE is 0, do something useful: if(resInt == 0) { ProgressBar progress = (ProgressBar) row.findViewById(R.id.update_progress); progress.setIndeterminate(true); TextView edit1 = (TextView)row.findViewById(R.id.row_id); TextView edit2 = (TextView)row.findViewById(R.id.request); TextView edit3 = (TextView)row.findViewById(R.id.result); edit1.setText("1"); edit2.setText("2"); edit3.setText("3"); row = inflater.inflate(R.layout.row, null); } return row; } here is the Stack Trace: 03-08 03:15:29.639: ERROR/AndroidRuntime(619): java.lang.NullPointerException 03-08 03:15:29.639: ERROR/AndroidRuntime(619): at android.widget.SimpleCursorAdapter.bindView(SimpleCursorAdapter.java:149) 03-08 03:15:29.639: ERROR/AndroidRuntime(619): at android.widget.CursorAdapter.getView(CursorAdapter.java:186) 03-08 03:15:29.639: ERROR/AndroidRuntime(619): at com.dhristov.test1.test1$mySimpleCursorAdapter.getView(test1.java:105) 03-08 03:15:29.639: ERROR/AndroidRuntime(619): at android.widget.AbsListView.obtainView(AbsListView.java:1256) 03-08 03:15:29.639: ERROR/AndroidRuntime(619): at android.widget.ListView.makeAndAddView(ListView.java:1668) 03-08 03:15:29.639: ERROR/AndroidRuntime(619): at android.widget.ListView.fillDown(ListView.java:637) 03-08 03:15:29.639: ERROR/AndroidRuntime(619): at android.widget.ListView.fillSpecific(ListView.java:1224) 03-08 03:15:29.639: ERROR/AndroidRuntime(619): at android.widget.ListView.layoutChildren(ListView.java:1499) 03-08 03:15:29.639: ERROR/AndroidRuntime(619): at android.widget.AbsListView.onLayout(AbsListView.java:1113) 03-08 03:15:29.639: ERROR/AndroidRuntime(619): at android.view.View.layout(View.java:6830) 03-08 03:15:29.639: ERROR/AndroidRuntime(619): at android.widget.LinearLayout.setChildFrame(LinearLayout.java:1119) 03-08 03:15:29.639: ERROR/AndroidRuntime(619): at android.widget.LinearLayout.layoutVertical(LinearLayout.java:998) 03-08 03:15:29.639: ERROR/AndroidRuntime(619): at android.widget.LinearLayout.onLayout(LinearLayout.java:918) 03-08 03:15:29.639: ERROR/AndroidRuntime(619): at android.view.View.layout(View.java:6830) 03-08 03:15:29.639: ERROR/AndroidRuntime(619): at android.widget.LinearLayout.setChildFrame(LinearLayout.java:1119) 03-08 03:15:29.639: ERROR/AndroidRuntime(619): at android.widget.LinearLayout.layoutVertical(LinearLayout.java:998) 03-08 03:15:29.639: ERROR/AndroidRuntime(619): at android.widget.LinearLayout.onLayout(LinearLayout.java:918) 03-08 03:15:29.639: ERROR/AndroidRuntime(619): at android.view.View.layout(View.java:6830) 03-08 03:15:29.639: ERROR/AndroidRuntime(619): at android.widget.FrameLayout.onLayout(FrameLayout.java:333) 03-08 03:15:29.639: ERROR/AndroidRuntime(619): at android.view.View.layout(View.java:6830) 03-08 03:15:29.639: ERROR/AndroidRuntime(619): at android.widget.LinearLayout.setChildFrame(LinearLayout.java:1119) 03-08 03:15:29.639: ERROR/AndroidRuntime(619): at android.widget.LinearLayout.layoutVertical(LinearLayout.java:998) 03-08 03:15:29.639: ERROR/AndroidRuntime(619): at android.widget.LinearLayout.onLayout(LinearLayout.java:918) 03-08 03:15:29.639: ERROR/AndroidRuntime(619): at android.view.View.layout(View.java:6830) 03-08 03:15:29.639: ERROR/AndroidRuntime(619): at android.widget.FrameLayout.onLayout(FrameLayout.java:333) 03-08 03:15:29.639: ERROR/AndroidRuntime(619): at android.view.View.layout(View.java:6830) 03-08 03:15:29.639: ERROR/AndroidRuntime(619): at android.view.ViewRoot.performTraversals(ViewRoot.java:996) 03-08 03:15:29.639: ERROR/AndroidRuntime(619): at android.view.ViewRoot.handleMessage(ViewRoot.java:1633) 03-08 03:15:29.639: ERROR/AndroidRuntime(619): at android.os.Handler.dispatchMessage(Handler.java:99) 03-08 03:15:29.639: ERROR/AndroidRuntime(619): at android.os.Looper.loop(Looper.java:123) 03-08 03:15:29.639: ERROR/AndroidRuntime(619): at android.app.ActivityThread.main(ActivityThread.java:4363) 03-08 03:15:29.639: ERROR/AndroidRuntime(619): at java.lang.reflect.Method.invokeNative(Native Method) 03-08 03:15:29.639: ERROR/AndroidRuntime(619): at java.lang.reflect.Method.invoke(Method.java:521) 03-08 03:15:29.639: ERROR/AndroidRuntime(619): at com.android.internal.os.ZygoteInit$MethodAndArgsCaller.run(ZygoteInit.java:860) 03-08 03:15:29.639: ERROR/AndroidRuntime(619): at com.android.internal.os.ZygoteInit.main(ZygoteInit.java:618) 03-08 03:15:29.639: ERROR/AndroidRuntime(619): at dalvik.system.NativeStart.main(Native Method)

  Read the article

• Looking for USB Network Attached Storage (NAS) Adapter that supports multiple drives, NTFS/FAT32 fil

  - by braveterry

  I'm looking for a NAS Adapter that supports attaching multiple USB devices to the network. Here's what I'd like to see in a NAS adapter: Under $100.00. Support for multiple devices. This can be through a USB hub or through multiple USB connectors on the device itself. Bittorrent support would be nice, but this isn't a deal-breaker. Filesystem support for at least NTFS or FAT32. I'd prefer to not have to reformat to use the device, but this is also not a deal-breaker. Here is what I am NOT looking for: I'm NOT looking for a NAS enclosure. I already have a couple of spare external USB drives that I'd like to use. I'm NOT looking for a networked USB hub like the one mentioned here. Network USB hubs only allow access to a drive from one PC at a time. I'm NOT looking for a wireless router with a NAS built in. I already have a wireless router, and I'd rather not go through the hassle of replacing it if possible. What I've looked at so far PogoPlug: This supports multiple devices via a USB hub, but there's not Bittorrent support. It's $99.00, so I may end up going with this and hope that they patch in Bittorrent support later. Addonics NAS Adapter: This supports only one device per adapter, so it's a non-starter. SimpleNET NAS Head USB 2.0 Portable Dongle: I'm not 100% sure this supports multiple devices. Plus there doesn't seem to be any Bittorrent support. I'll try to update this post as I explore other devices.

  Read the article

• How to diagnose disk errors when disk appears to be ok?

  - by Kylotan

  I have a six-month-old 1TB Seagate drive formatted into 2 NTFS partitions, and the disk appeared to be failing with Windows dropping down from UDMA to PIO mode, reporting Delayed Write Errors, and hanging Explorer when browsing directories. My initial suspicion was that the disk was dying. However, on further examination it appears that Ubuntu, which doesn't write to the volume frequently like Windows does, was able to read the disk properly and retrieve all the data intact, saving me from having to use an older backup. Finally, running the Seatools DOS diagnostic reported that the disk has no problems, ie. SMART errors and no bad sectors, apparently. This, in combination with the relative youth of the disk, suggests that something else is broken. The cable? The PSU? The integrated disk controller? But what would be a good way to diagnose the problem without risking damaging the data? I intend to extract the disk and try it in an external eSATA enclosure and see if the write errors cease, but in the event of the disk appearing to be fine, I would like to be able to confirm what part of the hardware is actually broken here in order to know just what needs replacing. Are there any good ways to go about this?

  Read the article

• How to diagnose disk errors when disk appears to be ok?

  - by Kylotan

  I have a six-month-old 1TB Seagate drive formatted into 2 NTFS partitions, and the disk appeared to be failing with Windows dropping down from UDMA to PIO mode, reporting Delayed Write Errors, and hanging Explorer when browsing directories. My initial suspicion was that the disk was dying. However, on further examination it appears that Ubuntu, which doesn't write to the volume frequently like Windows does, was able to read the disk properly and retrieve all the data intact, saving me from having to use an older backup. Finally, running the Seatools DOS diagnostic reported that the disk has no problems, ie. SMART errors and no bad sectors, apparently. This, in combination with the relative youth of the disk, suggests that something else is broken. The cable? The PSU? The integrated disk controller? But what would be a good way to diagnose the problem without risking damaging the data? I intend to extract the disk and try it in an external eSATA enclosure and see if the write errors cease, but in the event of the disk appearing to be fine, I would like to be able to confirm what part of the hardware is actually broken here in order to know just what needs replacing. Are there any good ways to go about this?

  Read the article

• Reinserted a RAID disk. Defined as foreign. Is import or clear the correct choice?

  - by Petrus

  I have re-inserted a RAID disk, on a DELL server with Windows Server 2008. The drive-status indicator was changing between a green and amber light, and the monitor gave the following message: There are offline or missing virtual drives with preserved cache. Please check the cables and ensure that all drives are present. Press any key to enter the configuration utility. I pressed a key and the PERC 6/I Integrated BIOS Configuration Utility showed that the RAID Status for that disk was Offline. After reinsertion of the disk the monitor is giving the following message: Foreign configuration(s) found on adapter. Press any key to continue or ‘C’ load the configuration utility, or press ‘F’ to import foreign configuration(s) and continue. After checking around on the net I am uncertain if I should choose import or clear. I cannot find out if an import means importing information from the array/system to the now foreign disk or the other way, i.e. importing information from the foreign disk to the array/system that was actually working fine. Also; if clear is a necessary thing to do ahead of a rebuild of that disk, or if clear means to clear the system to somehow make it ready to import the information from the foreign disk to the array/system, which is not what I want. I imagine that making the wrong choice here might be fatal. Please help clearing this out by telling what to choose and why.

  Read the article

• Where do I connect the HDD LED wires on my RAID adapter?

  - by Giffyguy

  I'm using a Promise FastTrak TX8660 with RAID 5. The manual (and Google) just doesn't seem to explain how exactly to connect a standard two-pin HDD LED wire to the eight available pins on the card. The Manual just says - To connect your LED, follow the following diagram: The card itself resembles the diagram: But it doesn't make any sense to me. All I have is a two-pin connecter for HDD LED on the front of my computer case. I don't need anything fancy like the fault LED or seperate indicators for each drive. I just want to be able to see when my RAID 5 array is working, that's all. I don't know what the "R" and "G" stand for, but my HDD LED wires are red and white. I tried connecting the red wire to the "R" pin and the white wire to the "G" pin, but that just makes the LED on the front of my case light up indefinitely, even when the computer is idle. Which pins am I suppose to connect the HDD LED header to for basic activity indication?

  Read the article

• QNAP NAS 509 (LINUX) - how to unmout busy volume and find physical disk?

  - by Horst Walter

  On my NAS QNAP TS 509 I do have a technical issue. I need to run e2fsck. This works fine for me on md0 (see below), but how can I unmount the busy devices md9 and sda4 in order to do the same. Whenever I try, I fail because the device is busy. [This part is solved, see below] In order to further track down the issue, I'd need to sort out the physical disk to device relationship. How can I find out this, e.g. md0 is a stripped volume on 2 disk (but I need to find out on what physical disk). Remark: As you can easily derive from my questions, I am not a Linux expert, but manage to get along. /dev/ram0 124.0M 94.1M 29.8M 76% / tmpfs 32.0M 80.0k 31.9M 0% /tmp /dev/sda4 310.0M 103.9M 206.1M 34% /mnt/ext /dev/md9 509.5M 39.2M 470.2M 8% /mnt/HDA_ROOT /dev/md0 1.8T 1.4T 444.7G 76% /share/MD0_DATA tmpfs 32.0M 0 32.0M 0% /.eaccelerator.tmp -- Added -- QNAP seems to be based on Busybox. I do not find something like init / telinit / runlevel. At busybox docs it says that I need to run the below. But in /var/service sv is not available. I want to go to single user mode to unmount the devices. # cd /var/service # sv d * # sv u getty* -- Added, thanks A4L -- This QNAP Box runs a special flavor of Linux, so not all SOPs do apply. In my particular case I found a services.sh script, stopping all services. After that the drive could be unmounted. The information passed by A4L is valid and worth reading it, maybe I'll profit from it next time. Links: http://unix.stackexchange.com/questions/19918/umount-device-is-busy and http://unix.stackexchange.com/questions/15024/umount-device-is-busy-why So the unmount issue is solved, still looking for the best option to find the physical to volume mapping.

  Read the article

• windows 8.1 does not boot after CHKDSK command

  - by sepehr

  I had problem with Windows 8.1 high Disk usage so in order to solve , searched forums. A voted answer suggested to use CHKDSK command as follow: run command prompt and as administrator type code snippet below: CHKDSK /f /v /b C: (I can not remember accurately) CHKDSK printed : can not run CHKDSK right now , would you like to schedule C drive to be checked next time windows starts? (Y/N) my response was "Y" ,please ! Following this suggestion not only didn't solve my problem as expected but also added another one ! The next time system booted, after windows authentication I just could see a black screen and mouse pointer. So I force shut downed the system and tried to start windows again. This time , windows got stuck in Scanning and Repairing on 22% for around 3 hours so I got tired and forced shut downed again. is CHKDSK source of Scanning and Repairing problem or they are discrete ? is there any hope to overcome this problem without re-installing windows ? can any one else run CHKDSK on newer versions of windows without problem? is CHKDSK effective but inefficient ?(it finally get to end but will take a long time) If yes, how much time does it take? I also have Linux Ubuntu 14.04 installed along side windows.

  Read the article

• BIOS setting: AHCI or RAID (when using SSD + 2x HDD in RAID-0)

  - by nixdagibts

  Hello there, I want to add a new SSD and use it as system drive with Win7 x64 installed. As driver I chose newest Intel Rapid Storage driver (not MSAHCI). I know that I have to use AHCI as BIOS setting for optimal SSD read/write performance. But I'm also using 2 normal HDDs as separate RAID-0 SSD: Win7 HDD: RAID-0 HDD: RAID-0 If I set my BIOS on my ASUS P5W DH Deluxe to AHCI, my RAID-0 cant be recognized And If im using RAID as setting, maybe my SSD has not its top speed. But I'm not sure about that. In short: AHCI no RAID-0 RAID no optimal SSD performance (?) Now my question: Can I use RAID as BIOS setting and be sure, that theres no decrease in SSD performance? Google finds so many articles with similar topics and my head is just exploding. Two examples: - set AHCI and after installing OS switch to RAID as BIOS setting... what? - use a diskette and F6 while installing win7... really? O.o I thought those times are gone

  Read the article

• Windows and file system abstraction - how much does it matter where something comes from?

  - by deceze

  I have come across the following phenomenon and would like to know how leaky Windows' file system abstraction is or if there's something else involved. I partitioned the hard disk of my MacBook Pro and installed Windows 7 (64 bit). The Bootcamp driver package includes file system drivers (right term?) that enable Windows to access the Mac OS HFS+ partition. AFAIK it's a read-only access, but it works. Now, I have some disk images of stuff I usually install, so I grabbed a copy of Daemon Tools to mount them. When I mount an image saved on the HFS+ partition, about two out of three installers on these disks (usually InstallShield) crash with all sorts of weird errors. Most are just gibberish that lead to all sorts of non-solutions on Google, one was "This application is not the right type for your computer, check if you need 32 or 64 bit versions." When moving the image files to another Windows 7 computer on the network and mounting them from the network share, they work fine. My question now is, why do applications behave differently depending on whether the read-only image file, which should be abstracted away through the read-only virtual Daemon Tools drive, is located on a read-only HFS+ partition or on a Windows network share? And I'll just roll this into the question as well since I was wondering: Does the file system of a network share matter? Does the client system need to understand the file system of the share host or is that abstracted away in SMB?

  Read the article

• Managing disk in a VM

  - by dst

  I'm replacing my two old rack servers with a new one that has plenty of power to take over the functionality my current servers. The server is a 4U rack mount with 16 3.5" SAS drive bays, two 2.5" bays, a Xeon E3-1230v2 CPU and 32GB of ECC RAM. My issue is the following. I would like to have a FreeBSD file server with ZFS managing disks. However, I need other VMs for e.g. a shell/git server, mail server etc. I'm wondering how to deal with the following issues: I want ZFS to fully manage the disks, so I'm not using any hardware RAID. Should I pass the SAS controller directly to the FreeBSD system as passthrough PCI? I want to maximize the reliability of the setup. On what disks should I install the hypervsor and keep server system disks? For (2) I have the option of having a RAID setup on the SAS controller and using that as system disk to store the hypervisor as well as VM images. However, this makes PCI passthrough to the file server impossible. Another option is using the two 2.5" bays. In terms of reliability how are SSDs compared to e.g. WD RE4 disks? Would it make sense to have two SSDs in software RAID as boot disks for the hypervisor or should I just go with e.g. WD RE4 disks in a software RAID setup. I also need to think about where to store the mails for the mail server, but this could be done over NFS between the VMs. BTW, this is for home use, so the load is not really that big. What I'm looking for is best practices for splitting up a server.

  Read the article

• Why does gcc think that I am trying to make a function call in my template function signature?

  - by nieldw

  GCC seem to think that I am trying to make a function call in my template function signature. Can anyone please tell me what is wrong with the following? 227 template<class edgeDecor, class vertexDecor, bool dir> 228 vector<Vertex<edgeDecor,vertexDecor,dir>> Graph<edgeDecor,vertexDecor,dir>::vertices() 229 { 230 return V; 231 }; GCC is giving the following: graph.h:228: error: a function call cannot appear in a constant-expression graph.h:228: error: template argument 3 is invalid graph.h:228: error: template argument 1 is invalid graph.h:228: error: template argument 2 is invalid graph.h:229: error: expected unqualified-id before ‘{’ token Thanks a lot.

  Read the article

• Why is it bad to map network drives in Windows?

  - by Beeblebrox

  There has been some spirited discussion within our IT department about mapping network drives. In particular, it has been said that mapping network drives is A Bad Thing and that adding DFS paths or network shares to your (Windows Explorer/Libraries) Favourites is a far better solution. Why is this the case? Personally I find the convenience of z:\folder to be better than \\server\path\folder', particularly with cmd line and scripting (of course I'm not talking about hard-coded links, naturally!). I have tried searching for pros and cons of mapped network drives, but I haven't seen anything other than 'should the network go down, the drive will be unavailable'. But this is a limitation of any network-accessed storage... I have also been told that mapped network drives poll the network when the network resource is unavailable, however I haven't found more information on this. Wouldn't this still be an issue with other network access mechanisms (that is, mapped Favourites) whenever Windows tries to enumerate the file system (for example, when a file/folder picker dialog is opened)? -- Do network drives poll the network any more than a Windows Explorer library/favourite?

  Read the article

• linux: mount old ATA disk to USB adapter

  - by 130490868091234

  I am trying to recover data from an old Linux that was installed in a computer on an ATA hard drive. I found a ScanLogic Corp. SL11R-IDE IDE Bridge (04ce:0002), an ATA adapter to USB 1.0 like the one in the picture: and after switching it on, I plugged it into a laptop with Ubuntu 12.04. I am used to the drives being automatically mounted, but this one doesn't show up in /media. After doing a dmesg, all I got is this: [215298.671924] usb 2-1.1: new full-speed USB device number 5 using ehci_hcd [215298.767330] scsi19 : usb-storage 2-1.1:1.0 [215299.841701] usb 2-1.1: reset full-speed USB device number 5 using ehci_hcd [215300.017258] usb 2-1.1: reset full-speed USB device number 5 using ehci_hcd [215300.197050] usb 2-1.1: reset full-speed USB device number 5 using ehci_hcd [215300.372730] usb 2-1.1: reset full-speed USB device number 5 using ehci_hcd I tried plugging in the adapter to the three different USB ports in my laptop (one of them USB 3.0), but got no luck with any of them. I get different devices under, for example: /dev/bus/usb/003/002 or /dev/bus/usb/002/004, but I don't get any /dev/sdbN links. The output blkid -o list -c /dev/null is just the laptop's partitions. I have tried taking out the jumper, putting it as master and as CS Enabled, but didn't change the result. Any ideas?

  Read the article

• LG LW20 Express won't boot after hdd replace

  - by Mika

  My old laptop (LG LW20 Express) got a hdd failure and I replaced the hdd. Now the laptop won't boot from cd or usb. I'm trying to install ubuntu on it. When I turn the laptop on it shows me the startup screen but when it should be the time to load operating system it just gives a black screen and starts over. This loop continues until I shut down the laptop. I created the usb boot drive following this guide https://help.ubuntu.com/community/Installation/FromUSBStick/ I used my boot cd to install ubuntu on this machine I'm using right now. So at least the cd should work. From the BIOS I can see that my newly installed hdd is recognized and put as a secondary master. Also the cd and removable media are in the boot list before hdd. The laptop runs pretty hot. The fan is at full speed pretty soon after the laptop is turned on. Earlier I suspected that it would have been the almost broken hdd that would have produced that heat but there obviously is something else also. Any ideas what to check?

  Read the article

• Why can't I mount an image hosted on a read-only HFS+ partition via Boot Camp?

  - by deceze

  I have come across the following phenomenon and would like to know how leaky Windows' file system abstraction is or if there's something else involved. I partitioned the hard disk of my MacBook Pro and installed Windows 7 (64 bit). The Boot Camp driver package includes file system drivers that enable Windows to access the Mac OS HFS+ partition. It's read-only access, but it works. Now, I have some disk images of stuff I usually install, so I grabbed a copy of Daemon Tools to mount them. When I mount an image saved on the HFS+ partition, about two out of three installers on these disks (usually InstallShield) crash with all sorts of weird errors. Most are just gibberish that lead to all sorts of non-solutions on Google, one was "This application is not the right type for your computer, check if you need 32 or 64 bit versions." When moving the image files to another Windows 7 computer on the network and mounting them from the network share, they work fine. My question now is, why do applications behave differently depending on whether the read-only image file, which should be abstracted away through the read-only virtual Daemon Tools drive, is located on a read-only HFS+ partition or on a Windows network share? And I'll just roll this into the question as well since I was wondering: Does the file system of a network share matter? Does the client system need to understand the file system of the share host or is that abstracted away in SMB?

  Read the article

• Why do disk images hosted on a read-only HFS+ partition behave differently?

  - by deceze

  I have come across the following phenomenon and would like to know how leaky Windows' file system abstraction is or if there's something else involved. I partitioned the hard disk of my MacBook Pro and installed Windows 7 (64 bit). The Boot Camp driver package includes file system drivers that enable Windows to access the Mac OS HFS+ partition. It's read-only access, but it works. Now, I have some disk images of stuff I usually install, so I grabbed a copy of Daemon Tools to mount them. When I mount an image saved on the HFS+ partition, about two out of three installers on these disks (usually InstallShield) crash with all sorts of weird errors. Most are just gibberish that lead to all sorts of non-solutions on Google, one was "This application is not the right type for your computer, check if you need 32 or 64 bit versions." When moving the image files to another Windows 7 computer on the network and mounting them from the network share, they work fine. My question now is, why do applications behave differently depending on whether the read-only image file, which should be abstracted away through the read-only virtual Daemon Tools drive, is located on a read-only HFS+ partition or on a Windows network share? And I'll just roll this into the question as well since I was wondering: Does the file system of a network share matter? Does the client system need to understand the file system of the share host or is that abstracted away in SMB?

  Read the article

• Getting 0xc00000e windows 7 "Boot device inaccessible" after random crashes

  - by Dynde

  I've been having some weird random crashes that I can't seem to locate, and I'm unsure if it's windows or hardware related. It's a brand new computer and very powerful. I've run into a couple of these random crashes, now I don't know what causes them, as it happens during the night, when I'm sleeping. When I wake up, all I see is a boot manager screen that says Exception: 0xc00000e "Boot device inaccessible". A simple restart doesn't fix the problem - it seems to struggle locating my primary hdd - but a complete shutdown works, it'll just fly straight into windows again. The event viewer doesn't tell me much. The most reason incident just gives me this: "The previous system shutdown at 08:55:44 on ?11-?12-?2011 was unexpected." And also a kernel power event: The system has rebooted without cleanly shutting down first. This error could be caused if the system stopped responding, crashed, or lost power unexpectedly. and I can see only two application event entries around that time at 8.47 (about 8 minutes prior to the crash): The Windows Modules Installer service entered the running state. The WinHTTP Web Proxy Auto-Discovery Service service entered the running state. Can anyone tell me anything about this, or direct me to a forum or something that might know what's wrong? I can supply the extra details of the events too if needed. The hdd is an SSD - could that have anything to do with it? I ran a few diagnostics and memory and hdd should be okay - at least the diagnostics report is clean. Is it a faulty drive?

  Read the article

< Previous Page | 201 202 203 204 205 206 207 208 209 210 211 212  | Next Page >