Search Results

Search found 54503 results on 2181 pages for 'net mvc'.

Page 2059/2181 | < Previous Page | 2055 2056 2057 2058 2059 2060 2061 2062 2063 2064 2065 2066  | Next Page >

• USB 3.0 ports backwards compatibility problems with 2.0 devices?

  - by AaronLS

  I see some info on the net that suggest that I should be able to get my USB 2.0 devices to work in 3.0 ports. I only have two 2.0 ports on my new computer, and six 3.0 ports. I have installed drives. There's two different drivers, I guess some of the ports are supported by the intel board and some supported by some other chipset on the motherboard. I however have yet to get any of the 3.0 ports to work, and my brother had had the same issue with his devices not working in 3.0 ports on his computer. So I am beginning to wonder if the backwards compatibility isn't reliable for some reason. Maybe manufacturers opting not to implement 2.0 support on the 3.0 ports. I understand that physically the wiring is there, but that is only half the story. Beyond my brother's and my own computers (different motherboards/everything), I have yet to see a 2.0 device work in a 3.0 port. Is there any reason for this apparent device incompatibility? I.e. looking for responses that would indicate what areas to explore for issues or if there is any known cases of manufacturers deviating from spec in hardware or drivers. I am aware it's "supposed" to work :) Update: Does this have any relation to "USB Legacy Support" options in the BIOS? There several options combinations of options with "USB Legacy Support" and "USB 3.0 Legacy Support" and the description for these is a bit confusing, sounds like a bad translation.

  Read the article

• Simulate a DFS share for a user not on domain with a folder in path

  - by user223655

  I have a consultant whose computer is not on the domain and needs to access various network resources. Unfortunately while adding a computer to the domain is a difficult bureaucratic process (and would disallow much of his development software from even running given the domain restrictions), we can allow him to have credentials to access network resources. As such, he accesses various network resources via NET USE etc. without using DFS. There is one piece of software which requires him to have the same hardcoded path as other domain users but that path is a DFS path which he can't map (i.e., the software checks the path at runtime and will only run if it matches the registered path and will reject it in the context of using a DFS versus conventional machine path) I was wondering if there's some method to simulate the DFS path without actually using DFS. e.g., the path the software needs to see is "\ABC\DFS\software\app.exe" whereas the non DFS path is "\DEF\Software\app.exe" while I could make his hosts file point DEF to ABC, I'm not sure if I can somehow make it point there with the DFS "folder" as well are there any methods for this short of making changes to the AD to allow him to use DFS or add him to the domain (both of which are politically/technically challenging sadly)? Thanks guys

  Read the article

• How do I configure IIS to allow access to network resources for PHP scripts?

  - by Dereleased

  I am currently working on a PHP front-end that joins together a series of applications running on separate servers; many of these applications generate files that I need access to, but these files (for various reasons) reside on their parent servers. If I, from the command line, issue a bit of script such as: <?php var_dump(glob("\\\\machine-name\\some\\share\\*")); I will get the full contents of that directory, proving that there's no problem programmatically with PHP reading the contents of a UNC share. However, if I try to execute the same script from the web server, I get an empty array -- more specifically, if I use more explicitly functions designed to "open" a directory like it was a file, I get access errors. I believe this to be a permissions issue, but I am not a server/network administrator type, so I'm not sure what I need to do to correct this and get my script running, and the links I've checked out have not been a terrible amount of help, perhaps due to my background, or lack thereof as far as IIS is concerned, coupled with the fact that we are not actually using .NET for this. Relevant Stats: Windows Server 2008 Standard SP2 IIS 7.0 PHP 5.2.9 I will be connecting to two types of servers: a few other nearly-identical Server 2008 machines, and a machine running embedded XP. Links that have not been particularly helpful but maybe I am just misreading: http://support.microsoft.com/?id=306158 http://support.microsoft.com/kb/207671/EN-US/ http://support.microsoft.com/kb/280383/

  Read the article

• How to setup bindings for development IIS 7.5 with lot of sites

  - by Antonio Bakula

  I am a programmer in a small ASP.NET shop with very little expirience in server administration, and I have to setup IIS 7.5 to host lot of sites on newly installed windows server 2008 R2, these sites are test "clones" for sites on "real" web server and they should be accessible only in local network (domain). Developers should add new sites for our new customers. Project managers use this server to check progress and test new sites and new features, QA people have to have access to this site and test before we copy it to the "real" web server. Developers only have access to IIS console, in fact they can use RDP to test server with their developer domain credentials and permissions, also developers are local admins on that machine (tester). On our previous server I used different port numbers for each site. That worked but don't like this solution, I would prefer to use subdomains. But here are the problems: manually adding DNS records is not an option because we do not wont that developers have to administer domain DNS server, and currently this had to be done with domain administrator credentials. Is there a some way to add DNS record automatically ? I tried to add DNS record for subdomains on test server with wildcard (*.tester) and that seems to work for some time but that change coused some bad problems in our domain network and admin forbid me to mess with DNS, he said that I have to add DNS record for every subdomain manually and that I can not use wildcards, and there is nothing that I can do about it, mainly for "politicall" reasons :( obviously our admin is pretty much uncooperative, outsorced from different organization and I can't do anything about that. can I add another DNS server on that machine ? What must be setup on clients machines to "tell" them to use domain DNS server and tester domain server ? So please I need someone to give me some advice, what should I do ? Is different port numbers only option left ? Thanks !

  Read the article

• yum trying to install el5 when I am on el6

  - by giorgio79

  When I run the following yum command I get this error: Package: git-1.7.10.1-1.el5.rf.x86_64 (rpmforge) Requires: libcurl.so.3()(64bit)" I read that this error is due to running an el5 rpmforge or having some el5 installed packages. How can I solve this problem? $ yum install git Loaded plugins: fastestmirror Loading mirror speeds from cached hostfile * base: centos.kiewel-online.ch * epel: fedora.kiewel-online.ch * extras: centos.kiewel-online.ch * rpmforge: mirror.de.leaseweb.net * updates: centos.kiewel-online.ch Setting up Install Process Resolving Dependencies --> Running transaction check ---> Package git.x86_64 0:1.7.10.1-1.el5.rf will be installed --> Processing Dependency: perl-Git = 1.7.10.1-1.el5.rf for package: git-1.7.10.1-1.el5.rf.x86_64 --> Processing Dependency: perl(Git) for package: git-1.7.10.1-1.el5.rf.x86_64 --> Processing Dependency: libexpat.so.0()(64bit) for package: git-1.7.10.1-1.el5.rf.x86_64 --> Processing Dependency: libcurl.so.3()(64bit) for package: git-1.7.10.1-1.el5.rf.x86_64 --> Running transaction check ---> Package compat-expat1.x86_64 0:1.95.8-8.el6 will be installed ---> Package git.x86_64 0:1.7.10.1-1.el5.rf will be installed --> Processing Dependency: libcurl.so.3()(64bit) for package: git-1.7.10.1-1.el5.rf.x86_64 ---> Package perl-Git.x86_64 0:1.7.10.1-1.el5.rf will be installed --> Finished Dependency Resolution Error: Package: git-1.7.10.1-1.el5.rf.x86_64 (rpmforge) Requires: libcurl.so.3()(64bit) You could try using --skip-broken to work around the problem You could try running: rpm -Va --nofiles --nodigest

  Read the article

• Kerberos issues after new server of same name joined to domain

  - by MentalBlock

  Environment: Windows Server 2012, 2 Domain Controllers, 1 domain. A server called Sharepoint1 was joined to the domain (running Sharepoint 2013 using NTLM). The fresh install for Sharepoint1 (OS and Sharepoint) is performed and set up for Kerberos and joined to the domain using the same name. Two SPNs added for HTTP/sharepoint1 and HTTP/sharepoint1.somedomain.net for account SPFarm. Active Directory shows a single, non-duplicate computer account with a create date of the first server and a modify date of the second server creation. A separate server also on the domain has the server added to All Servers in Server Manager. This server shows a local error in the events exactly like This from Technet (Kerberos error 4 - KRB_AP_ERR_MODIFIED). Question: Can someone help me understand if the problem is: The computer account is still the old account and causing a Kerberos ticket mismatch (granted some housekeeping in AD might have prevented this) (In my limited understanding of Kerberos and SPNs) that the SPFarm account used for the SPNs is somehow mismatched with HTTP calls made by the remote server management tools services in Windows Server 2012 Something completely different? I am leaning towards the first one, since I tested the same SPNs on another server and it didn't seem to cause the same issue. If this is the case, can it be easily and safely repaired? Is there a proper way to either reset the account or better yet, delete and re-add the account? Although it sounds simple enough with some powershell or clicking around in AD Users and Computers, I am uncertain what impact this might have on an existing server, particularly one running SharePoint. What is the safest and simplest way to proceed? Thanks!

  Read the article

• Microphone array support in Windows. Info on performance and compatible hardware?

  - by exinocactus

  It is officially claimed by Microsoft (Audio Device Technologies for Windows), that Windows Vista has an integrated system-level support of microphone arrays for improved sound capturing by isolating a sound source in target direction and rejecting ambient noise and reverberation. In more technical terms, an implementation of an adaptive beamformer. Theoretically, microphone arrays with 2-4 mics can substantially improve SNR under some conditions like speaker in front of the laptop in noisy environment (airport, cafe). Surprisingly, though, I find very little information about commercially-available products supporting these new features. I mean products like portable usb micropone arrays or laptops or flat screens with integrated mic arrays. I could only find info about two laptop models having "noise cancelling digital array microphone". These are Dell Latitude and Eee PC 1008P-KR. Now my questions: Do you have any experience with the Windows beamformer implementation? For instance, in the above mentioned laptops. How well does it work? Are there any tests results available in the net or in print (papers?)? Do you know about other microphone array hardware? What could be the reason why mic array technology didn't get sucess Is there mic arrays support in 'Windows 7'?

  Read the article

• Apache intermittently aborting requests

  - by Adam Phillips

  I have just been dealing with a problem whereby http requests are being aborted, seemingly at random. On any particular page in the website, when you opened a page, a number of the assets (img, css, etc) failed to load. If you refreshed, the page may work fine, the same set of assets may fail to load or different assets may fail to load. The net tab in firefox was returning 'Aborted' in the HTTP status code column for the failed assets, even tho in the case of images, the image previews were still working. There was nothing in any of the apache logs about the requests that failed, however since it seemed to point to an apache issue, we restarted apache. The first time we tried, it made no difference but about 10 minutes later, in the absence of a better solution we tried again. Bizarrely, the problem disappeared immeadiately. So now the site seems to be running fine again but its rather unsettling, both the intermittent nature of the problem and the lack of an explanation for its resolution. Has anyone seen anything like this before and if so did you find out the reason behind it? Many Thanks

  Read the article

• How to resume XMPP groupchat window in Irssi (using bitlbee)?

  - by mcnesium

  I use Bitlbee to chat in XMPP-networks within my IRC-client Irssi. This works great so far, and recently I started using XMPP Multi User Chats as an alternative to IRC-channels. I set up a channel using chat add <account> <[email protected]> in the &bitlbee control window, set chan <room> set autojoin true and entered /join #room in the &bitlbee window to join that groupchat. It then appears as a unique Irssi window in the status bar. This seems to work ok too, but with one exception: Since I idle in the channels 24/7 my irssi has to cope with the every-night-24h-DSL-disconnection by the ISP. After it automatically reconnects, it does kind of rejoin that XMPP-groupchat, but the traffic of the groupchat does not go back to the unique irssi window, but keeps flooding &bitlbee with messages from root telling me about a Groupchat Message from unknown JID <jid>: <message> - which is the traffic of the groupchat. The unique groupchat window is gone after the reconnect, and I will again have to go /join #room in &bitlbee to get it back. Even worse, the window number is unused before I rejoin the groupchat, and if I get a query from any network, the window nests in that unused window spot, so I will first have to remove that query from the spot, and then move the rejoined groupchat to that window number. I want my groupchat window to resume after the reconnect just like every other IRC channel too. How can I get this done? Any ideas?

  Read the article

• PHP potential issues with compiling 5.3.8 extensions against RHEL 6 / CentOS 6 PHP 5.3.3 package

  - by user101203

  I'm working on getting a Red Hat 6 LAMP server going and while the PHP that comes with it has many extensions we use, it doesn't have all of them. To solve this, I was thinking about either compiling the PHP extensions which come in the ext folder of the downloadable source code of PHP 5.3.3 from php.net same as #1, but using the extensions from the latest PHP version (currently 5.3.8). Do #1 but manually decide which updates to backport from the latest version of the PHP extensions into the older version and then compile the backported result A drawback to #1 is that security and bug fixes come out which we wouldn't be able to take advantage of. A drawback to #3 is that it might be a lot of work Does anyone know what the drawbacks to #2 are? I don't want to go down that route if it might result in some unexpected negative outcomes. Also, are there any other drawbacks to the other options or a better way to go altogether? I want to use the PHP 5.3.3 which comes with the Linux distro because I don't want us to get to a place again where we are forced to upgrade to a new version of PHP to stay on top of security updates like from PHP 5.2.x to 5.3.x and there be backwards incompatible changes (this is the situation we're in now with PHP 5.2.x no longer being supported).

  Read the article

• Problems setting up VLC Sever/client streaming

  - by Ayos

  I'm trying to set up a Linux machine as the server and a Windows XP machine as the client. Both machines are connected to the same local network via a Wi-Fi router. I setup the stream with the following properties : http stream port 8080 play locally And not much else. No firewall on the windows client(Windows firewall is disabled) When I try to open network stream via the client machine(Using VLC or Windows Media Player) I get the following errors: Media Player error code : 0xC00D11B3: Encountered a network Problem. VLC Console: main warning: connection timed out access_mms error: cannot connect to 192.168.1.3:8080 main debug: no access module matching "http" could be loaded main debug: TIMER module_need() : 12625.810 ms - Total 12625.810 ms / 1 intvls (Avg 12625.809 ms) main error: open of `http://192.168.1.3:8080' failed main debug: dead input main debug: repeating item main debug: starting playback of the new playlist item main debug: resyncing on http://192.168.1.3:8080 main debug: http://192.168.1.3:8080 is at 0 main debug: creating new input thread main debug: Creating an input for 'http://192.168.1.3:8080' main debug: using timeshift granularity of 50 MiB, in path 'C:\DOCUME~1\Accer\LOCALS~1\Temp' main debug: `http://192.168.1.3:8080' gives access `http' demux `' path `192.168.1.3:8080' main debug: creating demux: access='http' demux='' location='192.168.1.3:8080' file='\\192.168.1.3:8080' main debug: looking for access_demux module: 0 candidates main debug: no access_demux module matched "http" main debug: TIMER module_need() : 0.461 ms - Total 0.461 ms / 1 intvls (Avg 0.461 ms) main debug: creating access 'http' location='192.168.1.3:8080', path='\\192.168.1.3:8080' main debug: looking for access module: 2 candidates access_http debug: http: server='192.168.1.3' port=8080 file='' main debug: net: connecting to 192.168.1.3 port 8080 qt4 debug: IM: Deleting the input main debug: TIMER input launching for 'http://192.168.1.3:8080' : 13397.979 ms - Total 13397.979 ms / 1 intvls (Avg 13397.978 ms) qt4 debug: IM: Setting an input Need Help. Thanks in advance.

  Read the article

• 2 Computers, same network, different outgoing speeds when uploading to internet?

  - by user117339

  I have 2 work machines in my office, a PowerMac G5 and a MacBook Air. Both behind an IPCop firewall. The PowerMac is connected through a gigabit switch, the MacBook Air is connected through a Netgear 802.11g access point that is then plugged into the gigabit switch. There is also a FreeNAS box, both machines are able to read and write files to it at close to their pipe speeds. The main problem is when I am trying to upload files to the internet at large. The G5 is only hitting 0.1 - 0.25 Mbps. The Macbook is able to hit 2-3 Mbps. The setup (G5 / IPCop / Network) has been the same for 5 years. The issues with the internet speed started about 3 months ago. I hadn't tested on the Macbook at this point. I had complained to the ISP, they said their modem needed a firmware update, did that nothing changed. Reset IPCop, turned off squid, etc. No changes. The ISP switched the office over to a better plan with a theoretical 6 Mbps up, still no change. At this point I tried testing the Macbook, and lo and behold there's the speed. But why? I have tried changing out everything, cables, switches, using another ethernet port on the G5, wiping the system, using DHCP, using manual IPs, changing DNS servers, etc. Nothing works. I figured that if there was something horribly wrong with the network, then internally I would find a similar issue, but that is perfect. iperf, ping, etc show no dropped packets and near saturation of the internal network. I'm at a loss as to what the heck is going on. Any ideas would be appreciated! Below are some screenshots of speedtest.net: G5: Macbook Air:

  Read the article

• Can't access certain web sites - reset router, any ideas?

  - by IniTech

  EDIT: This problem was resolved by my ISP - had to do with damaged fiber in one of their locations. Thanks to everyone that helped. Not sure if this is the right site (I'm a StackOverflow user) so I thought I'd give it a shot. I'm having trouble connecting to certain sites on any of the 3 machines that are on my LAN. The following sites are returning "Problem Loading Page - The connection has timed out" Sourceforge.net CNet.com Microsoft.com OpenDNS.com even my company's webiste I was worried about possible malware/virus, but I don't think that is the case (given the inability to access my company's site and the fact that all 3 machines are having the same issues.) I've tried with IE8, FF, and Chrome I have reset my router (WRT54G) and my machine(s) multiple times. EDIT: It is also worth noting that this page spins constantly and no avatars show up (I'm assuming it is trying to access gravatar.com with no success.) EDIT: I have the same issues directly connected to the modem. So, any router config is probably not the issue I'm a programmer, not a network guy - any ideas?

  Read the article

• Uploading to another domain gives HTTP code 405

  - by dragon112

  I'm trying to upload a file (which can be quite large) from the website of one server to the backend of another server using plupload. Lets say: domain 1 = http://www.websitedomain.com/uploadform domain 2 = http://www.backenddomain.com/uploadhandler Trying to upload i send the following: OPTIONS /main/uploadnetwork.php HTTP/1.1 Host: backenddomain.com Connection: keep-alive Access-Control-Request-Method: POST Origin: http://www.websitedomain.com User-Agent: Mozilla/5.0 (Windows NT 6.1; WOW64) AppleWebKit/537.4 (KHTML, like Gecko) Chrome/22.0.1229.79 Safari/537.4 Access-Control-Request-Headers: origin, content-type Accept: */* Referer: http://www.websitedomain.com/uploadform Accept-Encoding: gzip,deflate,sdch Accept-Language: nl-NL,nl;q=0.8,en-US;q=0.6,en;q=0.4 Accept-Charset: ISO-8859-1,utf-8;q=0.7,*;q=0.3 DNT: 1 But when I try to start the upload the server returns the following: HTTP/1.1 405 Method Not Allowed Allow: GET, HEAD, OPTIONS, TRACE Content-Type: text/html Server: Microsoft-IIS/7.5 X-Powered-By: ASP.NET X-Powered-By-Plesk: PleskWin Date: Mon, 01 Oct 2012 12:41:57 GMT Content-Length: 999 After doing some research I found out that a browser does this to check if the server will accept the intended message. It looks like my server doesn't feel like accepting a simple POST call even tho i use post all the time. The Google Chrome console gives the following error: XMLHttpRequest cannot load http://www.backenddomain.com/uploadhandler. Origin http://www.websitedomain.com is not allowed by Access-Control-Allow-Origin. Does anyone know how to stop the browser from checking or how i can tell my server to just accept the POST?

  Read the article

• Working with different PHP version at the same time, php_value extension_dir not working?

  - by Gremo

  I need both PHP 5.4.7 and 5.3.17 running on Windows 7 x64 with Apache 2.2.23. This is my virtual host configuration: <VirtualHost *:80> DocumentRoot "C:/WAMP/Apache/htdocs/php54" ServerName php54.local PHPIniDir "C:/WAMP/PHP54" LoadModule php5_module "C:/WAMP/PHP54/php5apache2_2.dll" php_value extension_dir "C:/WAMP/PHP54/ext" <Directory "C:/WAMP/Apache/htdocs/php54"> Order allow,deny Allow from all </Directory> </VirtualHost> The PHPIniDir and LoadModule directives work fine and using phpinfo() inside my script prints the right PHP version. But I need to load extensions, and this is where it fails. php_value extension_dir should be C:/WAMP/PHP54/ext but it's (default one) C:/php. What I'm missing here? EDIT: Of course I can set this value directly in C:/WAMP/PHP54/php.ini, but I prefer passing it using vhost configuration: ; Directory in which the loadable extensions (modules) reside. ; http://php.net/extension-dir ; extension_dir = "./" ; On windows: extension_dir = "C:/WAMP/PHP54/ext"

  Read the article

• Linux as a gateway (no NAT)

  - by Hugo

  I'm trying to configure a linux server as a gateway/router, but I can't get it to work, and all information I've managed to find is NAT-related. I have a public IP block for the gateway and devices behind it, so I want the gateway to simply route packets to the internet - again: no NATing! I've managed to get the gateway to access the internet successfully (that was just a matter of configuring the IP and GW), and the computers behind it can communicate with it. [EDIT: more info] This is actually an IPv6 block (2800:40:403::0/48) (but I've found that most utilities and instructions can be easily adapted from IPv4 to IPv6 with little hastle). The server has too ports: wan: 2800:40:403::1/48 lan: 2800:40:403::3/48 One of the computers behind it is connected to it via a switch; 2800:40:403::7/48 The wan interface on the server can ping6 www.google.com without issues. The lan interface on the server and the client can mutually ping each other without issues (as well as SSH, etc). I've tried setting the server as a default gateway for the client, with no luck: client # route -A inet6 add default gw 2800:40:403::3 dev eth1 server # cat /proc/sys/net/ipv6/conf/all/forwarding 1 I don't want any filtering/firewalling/etc, just plain routing. Thanks.

  Read the article

• Internet compression proxy for low speed broadband?

  - by user23150

  I live in a rural location, using high-latency wireless off a local ISP's tower. My speed tests vary day to day, but I can get around 1Mb up/down. The problem is, I work with large files, uploading and downloading (HD videos, development software, etc.). It can be painful to wait sometimes. Plus I do some side contract game development, and it can be very difficult to playtest with other developers (200ms ping is a good day for me). Now, obviously it's not going to be easy to solve the latency problem without different wireless hardware. But speedwise, I am wondering if I can use some kind of compression technology on a proxy. For instance, my work computer has full access to a 26Mb down, 10Mb up connection, that is totally unused at night and the weekends. If I could run some kind of compression technology on our server, and use it as a proxy to route to my home computer, I could stand to gain some major speed. I realize that by bogging down a system with compression, I could potentially lose whatever speed gain I had. But the proxy server is a quad core xeon, and the receiving computer is a pretty decent i7 computer, so that shouldn't be a concern. I found http://toonel.net/ but it seems more geared toward very slow narrowband users, like dial-up. Plus, I would prefer to just be able to point my browser to a proxy server, rather then install software on my client machine. EDIT I thought about my question a little more, and realize I am going to need to install software on my client in order to decompress, and possible compress (for uploading). That's not a huge deal.

  Read the article

• Elevating UAC via .bat file?

  - by jslaker

  Pretty straightforward one that I'm having trouble finding an answer to. serverfault previously helped me with finding a way to automate Windows updates without using WSUS. It's working fantastically, but to run it over the network, you have to first mount a shared drive. That's pretty simple XP since you just mount the drive and run the updater. On Vista and W7, though, this all has to be done with elevated privileges to work correctly. The UAC account can't see network drives mounted by the regular user, so in order to get everything working, I have to mount the share via net use from an escalated shell. I'd like to automate mounting this share and launching the updater via a simple .bat file. I could probably just instruct everybody to right click "Run as Administrator" on the .bat file, but I'd like to keep things as simple as possible and have the .bat automatically prompt the user to escalate their privileges. Since these computers don't belong to us, I can't count on anything like Powershell being installed, so that rules any solution along those lines out and pretty much have to rely on things that would be included in an RTM Vista install. I'm hoping I'm mostly missing something obvious here. :)

  Read the article

• No outbound internet connection after restarting CentOS 6.3

  - by wnstnsmth

  After restarting a headless CentOS 6.3 machine, it lost outbound internet connectivity, i.e. I can still connect to the server via SSH (ssh root@**.126.18.56), but stuff such as ping google.com gives google.com: unknown host, and yum list some_package gives a lot of network errors. This is what ifconfig gives: eth0 Link encap:Ethernet HWaddr 00:25:90:78:2D:5D inet addr:**.126.18.56 Bcast:**.126.18.255 Mask:255.255.255.0 inet6 addr: fe80::225:90ff:fe78:2d5d/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:75594 errors:0 dropped:0 overruns:0 frame:0 TX packets:787 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:7074741 (6.7 MiB) TX bytes:144391 (141.0 KiB) Interrupt:20 Memory:f7a00000-f7a20000 eth1 Link encap:Ethernet HWaddr 00:25:90:78:2D:5C UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 b) TX bytes:0 (0.0 b) Interrupt:16 Memory:f7900000-f7920000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:6 errors:0 dropped:0 overruns:0 frame:0 TX packets:6 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:504 (504.0 b) TX bytes:504 (504.0 b) I have absolutely no clue how to debug this, and I find it very strange since I can still connect via ssh. EDIT: Weirdly, /etc/resolv.conf does not contain any entries, or none that I can make sense of: # Generated by NetworkManager search sui-inter.net # No nameservers found; try putting DNS servers into your # ifcfg files in /etc/sysconfig/network-scripts like so: # # DNS1=xxx.xxx.xxx.xxx # DNS2=xxx.xxx.xxx.xxx # DOMAIN=lab.foo.com bar.foo.com So is it possible that rebooting the server erased that file? It worked before at least! And how do I solve this? By the way, pinging an IP address works.

  Read the article

• Advice for UPC/Surge Protector in home office

  - by user37755

  I'm just starting out as an independant developer, mostly Unix stuff with some Windows thrown in occasionally. I've been running two machines, a linux and a windows dev machine. Long story short, we had a bad storm come through last week and I unplugged one machine, forgot to unplug the other and the p/s and mobo ended up dead. Luckily I backup to an external service religiously (rsync.net for anyone interested), so there was no loss in data, but it did show me a glaring hole in my current setup, namely, lack of UPC and Surge Protection (this has honestly never been an issue before). Can anyone recommend a UPC/Surge Protector for a home office? It only needs to support a single machine (I opted to use vmware instead of rebuilding that machine), but it's a quad core Phenom 2 with a 1k watt p/s. This is outside my experience so I thought I'd get some input from others. I'm looking for something that's reasonably priced and does the job reasonably well. I don't need absolute 100% uptime, just something to protect my PC better than it is now.

  Read the article

• Network problems that might be related to NAT

  - by nenne

  Hello, I have an odd setup where there is a router(Router 2) routing between network network 1 and network 2. One router(Router 1) with nat for internet access that routes between internet and network 1. There are people in both of these networks. All the clients in network 1 can access the internet, the clients in network 2 can access the clients in network 1 and can also access the router 1. Router 1 can also access clients in network 2. However, the clients in network 2 cannot reach the internet. I cannot think about anything in the routing tables that would hinder this, since Router 1 can reach the clients in network 2 and vice versa. Can it be that nat starts the session between router 2 and the internet site/machine instead of the client and the internet machine? Does anyone have any ideas? I have very little control over router 2(its basicly an ISP vpn net service) but full access to router 1. Its an ubuntu 10.04 with iptables for nat/firewall setup.

  Read the article

• SBS 2008 - DNS Forwarders timing out.

  - by Moif Murphy

  Hello, We have an SBS 2008 server that keeps losing connection to the internet approx 2-3 times a day. It's a simple setup, BT Business Broadband ADSL to a Wireless Zyxel router to the server. Clients connect via WiFi from their laptops. Plugging ethernet in makes no difference, only a reboot of the router seems to bring everything back again. I'm looking at the forwarders on the DNS properties page and they're timing out when trying to resolve the IPs. Currently there are two IPs in there, 194.72.9.34 which has timed out and 194.72.9.38 which has finally resolved to ns8.bt.net We've been in there and replaced all media, installed a PCI NIC, have changed the router three times. There are no errors in the DNS event logs pertaining to what's going on. We've also been on to BT who are adamant that it's not their end. Could someone shed some light on what could be going on or where else to look in the configuration of the server? Thank you.

  Read the article

• Setting up test an dlive enviornment - how?

  - by Sean

  I am a bit new to servers and stuff so had a question. I have my development team working on my website. They are in different countries and currently they put all the work live on the test site. But the test site is open to anyone who knows the URL. It is behind a directory but this effects my QA process because i cannot use the accurate URL structures to prevent the general public from seeing it. So what I want to do it: Have my site live on the net but only for me and my team, so like an internal network. Also I will need to mirror this to my live site when i put it live. So i guess this is something like setting up a staging and live environment. So how to do it and are both environments on the same physical server or do i need to buy two servers? And if i setup a staging environment how will i access it and my team since we are all spread out so i assume we need to log into something to access it? What about the URL - do i need a different URL for the test site or can i use the same live url for the test site? I plan to get a dedicated server + CDN for my site.

  Read the article

• Samba/Winbind issues joing to Active directory domain

  - by Frap

  I'm currently in the process of setting up winbind/samba and getting a few issues. I can test connectivity with wbinfo fine: [root@buildmirror ~]# wbinfo -u hostname username administrator guest krbtgt username [root@buildmirror ~]# wbinfo -a username%password plaintext password authentication succeeded challenge/response password authentication succeeded however when I do a getent I don't get any AD accounts returned [root@buildmirror ~]# getent passwd root:x:0:0:root:/root:/bin/bash bin:x:1:1:bin:/bin:/sbin/nologin daemon:x:2:2:daemon:/sbin:/sbin/nologin adm:x:3:4:adm:/var/adm:/sbin/nologin lp:x:4:7:lp:/var/spool/lpd:/sbin/nologin sync:x:5:0:sync:/sbin:/bin/sync shutdown:x:6:0:shutdown:/sbin:/sbin/shutdown halt:x:7:0:halt:/sbin:/sbin/halt mail:x:8:12:mail:/var/spool/mail:/sbin/nologin uucp:x:10:14:uucp:/var/spool/uucp:/sbin/nologin operator:x:11:0:operator:/root:/sbin/nologin puppet:x:52:52:Puppet:/var/lib/puppet:/sbin/nologin my nsswitch looks like this: passwd: files winbind shadow: files winbind group: files winbind #hosts: db files nisplus nis dns hosts: files dns and I'm definitely joined to the domain: [root@buildmirror ~]# net ads info LDAP server: 192.168.4.4 LDAP server name: pdc.domain.local Realm: domain.local Bind Path: dc=DOMAIN,dc=LOCAL LDAP port: 389 Server time: Sun, 05 Aug 2012 17:11:27 BST KDC server: 192.168.4.4 Server time offset: -1 So what am I missing?

  Read the article

• Secure NAT setup with iptables

  - by TheBigB

  I have Debian running device that needs to act as an internet-gateway. On top of that I want to provide a firewall that not only blocks inbound traffic, but also outbound traffic. And I figured iptables should be able to do the job. The problem: I've configured NAT properly (I think?), but once I set the default policy to DROP and add rules to for instance allow HTTP traffic from inside the LAN, HTTP is not going through. So basically my rules don't seem to work. Below is the initialization script that I use for iptables. The device has two NICs, respectively eth0 (the WAN interface) and eth1 (the LAN interface). echo 1 > /proc/sys/net/ipv4/ip_forward # Flush tables iptables -F iptables -t nat -F # Set policies iptables -P INPUT DROP iptables -P OUTPUT DROP # NAT iptables -t nat -A POSTROUTING -o eth0 -j MASQUERADE iptables -A FORWARD -i eth0 -o eth1 -m state --state RELATED,ESTABLISHED -j ACCEPT # Allow outbound HTTP from LAN? iptables -A FORWARD -i eth1 -o eth0 -p tcp --dport 80 -j ACCEPT iptables -A OUTPUT -p tcp --dport 80 -j ACCEPT Can anyone shed some light on this?

  Read the article

< Previous Page | 2055 2056 2057 2058 2059 2060 2061 2062 2063 2064 2065 2066  | Next Page >