Search Results

Search found 8555 results on 343 pages for 'virtualbox networking'.

Page 206/343 | < Previous Page | 202 203 204 205 206 207 208 209 210 211 212 213  | Next Page >

• I have a wireless Canon P560 and my computer can't find it

  - by ed

  The printer is wireless and I haven't connected it via USB. I set the configurations for the Wi-Fi access point in the printer and it connected to my Wi-Fi. I have AT&T as the service provider and the 2Wire router. When I access the router in the browser I see that the printer is connected but when I run the software to detect the printer the computer can't find it. I have a Mac with Snow Leopard. I tried to detect the printer with another device and it can't find it. Is there a port that needs to be open for wireless printers? Because I tried putting the routers firewall settings for the device to its lowest and the computer still can't find it. Let me know. Thnx.

  Read the article

• How can I start hostednetwork on Windows 7?

  - by Pirozek

  When I type in admin console command to start hostednetwork netsh wlan start hostednetwork it gives me this: The hosted network couldn't be started. The group or resource is not in the correct state to perform the requested operation. There is a hotfix from Microsoft but it didn't help me. Any advice? C:\Users\Pirozek>netsh wlan show driver Interface name: Wireless Network Connection 3 Driver : D-Link AirPlus DWL-G520 Wireless PCI Adapter(rev .B) Vendor : Atheros Communications Inc. Provider : Atheros Communications Inc. Date : 8.7.2009 Version : 8.0.0.171 INF file : C:\Windows\INF\oem108.inf Files : 2 total C:\Windows\system32\DRIVERS\athrx.sys C:\Windows\system32\drivers\vwifibus.sys Type : Native Wi-Fi Driver Radio types supported : 802.11b 802.11g FIPS 140-2 mode supported : Yes Hosted network supported : Yes Authentication and cipher supported in infrastructure mode: Open None Open WEP-40bit Shared WEP-40bit Open WEP-104bit Shared WEP-104bit Open WEP Shared WEP WPA-Enterprise TKIP WPA-Personal TKIP WPA2-Enterprise TKIP WPA2-Personal TKIP Vendor defined TKIP WPA2-Enterprise Vendor defined Vendor defined Vendor defined WPA-Enterprise CCMP WPA-Personal CCMP WPA2-Enterprise CCMP Vendor defined CCMP WPA2-Enterprise Vendor defined Vendor defined Vendor defined WPA2-Personal CCMP Authentication and cipher supported in ad-hoc mode: Open None Open WEP-40bit Open WEP-104bit Open WEP WPA2-Personal CCMP

  Read the article

• How to combine AWS and dedicated external servers?

  - by rfw21

  I have an extensive network of servers all currently hosted on AWS EC2. For reasons of cost I plan to gradually migrate to dedicated servers where possible. So: How can I best combine AWS and non-AWS servers in my network? Ideally, I should be able to assign internal IP addresses to the external servers, include them in AWS security groups and ensure that all private traffic between my AWS servers and external servers is secure.

  Read the article

• new PC not work with existing router, but works fine when directly connecting to cable modem

  - by user34786

  I bought a new desktop PC (eMachine ET1331G-03W from WalMart) with windows 7 installed, but I can not access internet by connecting to my existing wireless router(LinkSys BEFW11S4) with wired cable. Though all other existing desktops and laptops have no problem connecting to the same router. However, the new desktop PC works fine and able to connect to internet if I bypass the router and directly hook up with the cable modem. At new PC when connecting to the router, I got the below information by typing ipconfig, the IP address looks wrong to me: autoconfiguration IPv4 Address: 169.254.71.140 subnet mask: 255.255.0.0 default gateway: (empty) NetBIOS over Tcpip: Enabled Typing ipconfig at all other desktop and laptop have values like below, which are good to me: Connection-specific DNS Suffix . : IP Address. . . . . . . . . . . . : 192.168.1.140 Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : 192.168.1.1 The wireless router was on 192.168.1.1, I do not know why the new desktop got 169.254.71.140 IP? It should have something like 192.168.1.xxx, and it was configured to automatically get IP by DHCP. I have tried to switch cables,power off cable modem, router and reboot new pc many times and got no luck. So I believe this is only an issue related to router or new pc configuration. Can someone help me figure out the issue?

  Read the article

• Command or tool to display list of connections to a Windows file share

  - by BizTalkMama

  Is there a Windows command or tool that can tell me what users or computers are connected to a Windows fileshare? Here's why I'm looking for this: I've run into issues in the past where our deployment team has deployed BizTalk applications to one of our environments using the wrong bindings, leaving us with two receive locations pointing to the same file share (i.e. both dev and test servers point to dev receive location uri). When this occurs, the two environments in question tend to take turns processing the files received (meaning if I am attempting to debug something in one environment and the other environment has picked the file up, it looks as if my test file has disappeared into thin air). We have several different environments, plus individual developer machines, and I'd rather not have to check each individually to find the culprit. I'm looking for a quick way to detect what locations are connected to the share once I notice my test files vanishing. If I can determine the connections that are invalid, I can go directly to the person responsible for that environment and avoid the time it takes to randomly ask around. Or if the connections appear to be correct, I can go directly to troubleshooting where in the process the message gets lost. Any suggestions?

  Read the article

• WGet from one site on a server to another site on the same server

  - by JoshReedSchramm

  Hey all, I've recently been asked to administer a couple ubuntu boxes running web servers. I'm a dev by trade so if this question is fairly noob please forgive. We have about a dozen sites running on this box. 2 of our sites need to talk back and forth over a restful api. Unfortunately we are having issues with the sited connection to each other via wget. When we try and run wget manually from the command line from the server pointing to a site also on that server it hangs and eventually times out. If we do the same thing from outside the server to the same site on the server it works. Is there something that could be preventing sites on the same server from communicating with each other? The same thing happens pinging the site from the server.

  Read the article

• Computer Loses connection to router

  - by ajon

  I have a new Windows 8 Dell XPS desktop computer at work. It has a Dell Wireless 1703 802.11 b/g/n (2.4ghz) wireless adapter. sporadically throughout the day I lose internet connectivity. When I click on the wireless system tray icon, my companies router does not appear in the list. No other computer on the network is losing connection, only this one. I don't even know what to check. Could it be an ip conflict that causes me to get booted off? (I use DHCP), but why wouldn't my computer be able to see the network. The next time it happens I will see what happens when I try to access the router directly.

  Read the article

• How frequent are network partitions on cloud services?

  - by roja

  Much is made of the CAP trade-off for data storage where conflicts can be introduced if there is a network partition. My question is there any evidence that this is a problem that arises with any significant frequency in modern cloud IAAS services e.g.; EC2, Azure, Rackspace. Is it a problem which, despite being a theoretical roadblock in constructing idealised distributed systems is, in fact, a non-issue for all practical concerns? Has anyone experienced a network partition within one of these systems (within a single data-centre?) If so would you be willing to share any details?

  Read the article

• Using iptables to block ALL outgoing traffic from one NIC?

  - by edanfalls

  Hi, I must pretty bad at Googling as this seems like a very basic question but I can't seem to find the answer anywhere... and man iptables is a very long read! I have two NICs - eth0 and eth1 - on a linux box and I want to block ALL outbound traffic (TCP and UDP across all ports) from one of the NICs, so that no traffic makes its way back up to the router. What is the command for this? I have only seen examples with specific ports. Thanks in advance.

  Read the article

• Multiple connections to the same Wireless Network in Windows 7

  - by Jamek

  Hello, my university just limited bandwidth to 512 kbps (that's 64 kB/s!) for each connection. I was thinking to make multiple connection to the same wireless network (called "internet"), is this possible under Windows 7? I know it's possible to connect to more than one WLAN through the "hostednetwork" concept in netsh: netsh wlan set hostednetwork mode=allow ssid=xxxxx netsh wlan start hostednetwork However this method doesn't seem to work, I don't know if it's due to the authentication method (through certificates while hostednetwork seems to support just a "passphrase") or because I'm already connected to that network with the same MAC. Can you think to some tool able to do this?

  Read the article

• Why does my computer sometimes not identify my wireless network, or others, that it always connects to?

  - by Emile Erasmus

  I have a vista operating system. Sometimes my computer will not connect to the wireless network (internet) when I start up my laptop. This happens at different places on occasion, and it is very random. It tries to connect, but can not identify the network (it does recognize the wifi name). So at the end it connects, but with limited connectivity. It can not be the hardware because all other computers connect to it fine at the same time. And it happens at different places, mostly home, but sometimes at coffee shops, etc. And then in a day or two when I start up my laptop it is all of a sudden working again. (restart does not solve the problem). I have tried all the trouble shooting options windows offers, restarting the notebook, switch modem on and off, switch laptop wifi on and of, deleted the wifi memory from the laptop and reconnected with the password as if it was the first time, everything. If it does not work at one place it does not mean it won't work at another. Example it won't work at home, then I go to coffee shop and it works, then get back home and it don't. Anyone encountered this before?

  Read the article

• good PCI-e Wireless card for Windows7?

  - by benwebdev

  Hi I've just build a 64bit Windows 7 PC but am unhappy with the piddly performance of the linksys USB wireless dingle I've used. Can anyone suggest a good PCIe alternative that will be stronger for connection and maybe faster. I dont see why my desktop should show a weaker performance on wireless than my laptop when its sat next to it or even my Palm Pre for that matter. any thoughts? UK based max around £60ish. thanks, Ben

  Read the article

• command line bandwidth limiter for windows

  - by jackhab

  Please, recommend network bandwidth limiter for windows which can be controlled from command line. No need for fancy options, only limiting of up and down traffic on a host required.

  Read the article

• Connect Ralink RT2571 to new PC

  - by tuelsch

  I bought a new PC with the AsRock Z77 Extreme 4m motherboard, since this has no WLAN, I extracted the WLAN card from my old PC, a Ralink RT 2571 WF, an connected it to the new board. I downloaded the driver from http://www.ralinktech.com/en/04_support/support.php?sn=500 (the RT257x USB one) and installed it. In the device manager, an unknown device shows up, but if I tell it to search its driver, it does not find it (searching in the whole C partition). The Ralink Diagnostic Test says that the WLAN Card is disabled. I'm using Windows 7 64bit professional. Can anyone suggest me a solution to get my WLAN running?

  Read the article

• Justification of Amazon EC2 Performance

  - by Adroidist

  I have a .jar file that represents a server which receives over TCP an image in bytes (of size at most 500 kb) and writes it file. It then sobels this image and sends it over TCP socket to the client side. I ran it on my laptop and it was very fast. But when I put it on Amazon EC2 server m1.large instance, i found out it is very slow - around 10 times slower. It might be the inefficiency in the code algorithm but in fact my code is nothing but receive image (like any byte file) run the sobel algorithm and send. I have the following questions: 1- Is it normal performance of Amazon EC2 server- I have read the following links link1 and link2 2- Even if the code is not that efficient, the server is finally handling a very low load (just one client), does the "inefficient" code justify such performance? 3- My laptop is dual core only...Why would the amazon ec2 server have worse performance that my laptop? How is this explained? Excuse me for my ignorance.

  Read the article

• USB Wireless adapter that works with Windows 7 (32 and 64bit)

  - by Kjensen

  Can anybody recommend a USB wireless network adapter, that has Windows 7 drivers for both 32 and 64 bit? It also needs to reconnect to the network when the computer is brought out of sleep. I have three of these from earlier (from Allnet, trendnet and linksys), and just one of them has working drivers for Win7 64bit - but fail to return from sleep in a working state.

  Read the article

• Is it possible to kill a RAS connection which won't disconnect.

  - by sgmoore

  I have a Windows 2003 Server which has a number or RAS Connections to some of our customers. Occasionally the connections go into a mode where there are connected, but not working. Disconnecting and reconnecting solves the problem. However sometimes you can not disconnect as I get the following error message It is not possible to disconnect at this time. The connection is currently busy with a connect or disconnect operation. There are no visible connection dialog boxes when this message occurs and I usually end up having to restart the server which obviously affects all the other users. I know that if you have a service that is stuck 'stopping' you can just kill it. Is there anything similar that you can do to reset a ras connection?

  Read the article

• How to route local traffic over switch?

  - by Franz Kafka

  I'm just cabled up at home but haven't got any way of verifying that gigabit speed can be reached. As I've only got one laptop with one network card, one cable, and one switch, I'm kind of stuck. I'm using a tool that you can start as a server or as a client to send data from one box to another. I would like to send and receive on the same Windows box. I guess if I use my network local IP address, my Windows 8.1 PC will just route traffic internally. Is there some way of forcing the traffic to go to the switch and back again?

  Read the article

• Cisco RV016 dual WAN and VPN setup

  - by sklr

  I have a VPN of several RV016 routers and I want to set some of them with 2 ISPs. I plug the two ISP cables in WAN 1 and 2 ports and configure the router to "Intelligent Balancer(Auto Mode)". It works ok like that, but the VPNs that I set use the public IP of the provider. For example if I have 5 VPNs set for ISP1 (WAN1) and the balancer sends the request trough WAN2 it can't use any of the configured VPNs because the public IP is different. How do I deal with this problem?

  Read the article

• Auto logon to internet provider

  - by user31673

  We use wireless internet access. The wireless is secured and to get an IP address, you provide the right key. That is setup just fine. However, on top of that, the first time we access the internet, a browser page appears and we have to enter a password. then we have access to the internet for a period of time. How can the password step be automated? I also have a web-based printer that doesn't work (except via USB connection) because it can't get out to the web. I can't change the router settings. Is there anything I can do to get the printer working and automatic the access?

  Read the article

• Remove Windows 7's limitation on number of concurrent tcp connections (http web requests)

  - by Ghita

  I have an application that tries to open as many http requests as possible (in order to stress test a proxy implementation) It seems to me that Win7 (SP1) may have a limitation on number of concurrent opened connection (it may be the so called half-open state if I'm not wrong). Is there something I can do for client ? and also I test using a vista PC that acts as a proxy server. It would be great if I could configure it to sustain at least 50 new connections initiated / second on client side and many more on server. I made the modification according to this technet article by setting TcpNumConnections = 150 but it doesn't make a difference. I still only see about 20 tcp sockets associated with my http client by using tcpview.

  Read the article

• Mirror your display to another computer on your network

  - by klikkamongo

  I have a computer I am using for showing media, running windows 7 (XBMC). It is hooked up with a projector. I want other computers on my network to have the opportunity to mirror their display to this computer.(without the media computer having to accept it, it should be all controlled by the sending computer.(like sending a movie with Apple's Airplay)) One scenario: I am finding a webpage with a great article (or a Word document) on my computer that i want to show to the other people in the room, i press a button, then my screen is mirrored to the media pc. I can still scroll, write etc. so everybody can see it. When i am done showing the article, I can exit the display mirroring, and the media computer display goes back to normal. This should mirror the whole screen, not only the browser like plugins can do in chrome, or sending Youtube movies like plugins for Opera. Update I found a video example of the solution I am looking for, unfortunately it looks like it will be hard making a Chromecast reciever for windows. Using the "Cast entire screen (experimentally)" button on the Chromecast plugin in Chrome is doing the exact thing I want to do, see this video.

  Read the article

• How to know my wireless card has injection enabled?

  - by shrimpy

  I am playing around with aircrack. And was trying to see whether my wireless card on my laptop can pass the injection test And I end up seeing the following... does it mean my wireless card is not able to run aircrack? root@myubuntu:/home/myubuntu# iwconfig lo no wireless extensions. eth0 no wireless extensions. eth1 IEEE 802.11bg ESSID:"" Nickname:"" Mode:Managed Frequency:2.437 GHz Access Point: Not-Associated Bit Rate:54 Mb/s Tx-Power:24 dBm Retry min limit:7 RTS thr:off Fragment thr:off Power Management:off Link Quality=5/5 Signal level=0 dBm Noise level=-57 dBm Rx invalid nwid:0 Rx invalid crypt:781 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0 root@myubuntu:/home/myubuntu# aireplay-ng -9 eth1 ioctl(SIOCSIWMODE) failed: Invalid argument ARP linktype is set to 1 (Ethernet) - expected ARPHRD_IEEE80211, ARPHRD_IEEE80211_FULL or ARPHRD_IEEE80211_PRISM instead. Make sure RFMON is enabled: run 'airmon-ng start eth1 <#>' Sysfs injection support was not found either. root@myubuntu:/home/myubuntu#

  Read the article

• VPN service into 192 network

  - by tophersmith116

  I'm thinking about setting up a security testing lab. I work on a switched network, and that just makes for unnecessary headaches when doing testing. I'd like to create a 192 network with a few machines inside for DBs and AppServers etc. I will need a pivot machine that connects to both the outer network and the 192 (for automation purposes). But I'd like to be able to connect into the 192 network with my own machine from the outer network as the "attacking" machine (rather than have dedicated attack machines inside the 192 network). Therefore, I'd like to have the pivot server be a VPN server as well, so that my machine can VPN into the 192 network from the outer network. First off, is this even possible? Can I have a single computer with two NICs where a VPN service allows remote connections into the 192? Secondly, I'd like to have multiple outer clients connect to the VPN. Does anyone have any suggestions? I've used Hamachi well before, but I've also seen some good stuff from OpenVPN.

  Read the article

• Conflicting ip routes with local table on attaching a virtual network interface

  - by user1071840

  I have an EC2 instance with these ip rules: $ sudo ip rule show 0: from all lookup local 32766: from all lookup main 32767: from all lookup default I can attach an elastic network interface to it with a private IP. Say the IP of my machine is 10.1.3.12 and the IP of the interface is 10.1.1.190. As soon as I attach the interface to my machine a new entry is added to the routing policy and local routing table: sudo ip rule show 0: from all lookup local 32765: from 10.1.1.190 lookup 10003 32766: from all lookup main 32767: from all lookup default $ sudo ip route show table local broadcast 10.1.1.0 dev eth3 proto kernel scope link src 10.1.1.190 local 10.1.1.190 dev eth3 proto kernel scope host src 10.1.1.190 broadcast 10.1.1.255 dev eth3 proto kernel scope link src 10.1.1.190 broadcast 10.1.3.0 dev eth0 proto kernel scope link src 10.1.3.12 local 10.1.3.12 dev eth0 proto kernel scope host src 10.1.3.12 broadcast 10.1.3.255 dev eth0 proto kernel scope link src 10.1.3.12 broadcast 127.0.0.0 dev lo proto kernel scope link src 127.0.0.1 local 127.0.0.0/8 dev lo proto kernel scope host src 127.0.0.1 local 127.0.0.1 dev lo proto kernel scope host src 127.0.0.1 broadcast 127.255.255.255 dev lo proto kernel scope link src 127.0.0.1 I can send traffic to this ENI directly from a host that can have the same IP as the host the ENI is attached to. This is where the problem starts. I ran tcpdump on the port in question and saw multiple SYNs going to the ENI with src '10.1.3.12' and destination '10.1.1.190' but didn't see even a single ACK. In my understanding if ACKs were being sent from the ENI they'd have destination as 10.1.3.12 i.e. the same as the local machine's IP and such packets will now be routed as local packets matching local routing policy: local 10.1.3.12 dev eth0 proto kernel scope host src 10.1.3.12 I'd like to send all the packets originating from 10.1.1.190 (my ENI) to go back on the same interface i.e. eth3 in this case. Contents of the nee table 10003 are: $ sudo ip route show table 10003 default via 10.1.1.1 dev eth3 I think I can do the following: I don't know if its possible but probably decrease the priority of local table so the packets match the table 10003. Use iptables to mangle these packets and update the local table route to include the mark information But I'm not sure if these are the right approaches.

  Read the article

< Previous Page | 202 203 204 205 206 207 208 209 210 211 212 213  | Next Page >