Search Results

Search found 6376 results on 256 pages for 'git reset'.

Page 208/256 | < Previous Page | 204 205 206 207 208 209 210 211 212 213 214 215  | Next Page >

• Cannot connect to Solaris Server when Oracle GoldenGate process uses the port

  - by Abdallah Ghrb

  I'm trying to test the Oracle goldengate to replicate data between two databases on the same server. So I installed two databases and two goldengate homes in the same machine. The goldengate processes are started from each home and they are responsible for the replication : Process from home 1 configured on port 7809 & process for home 2 configured on port 7810. For a successful replication, processes started from goldengate home 1 should communicate with processes started from goldengate home 2. But for some reasons, this is not happening. The goldengate log file has the following error : OGG-01223 Oracle GoldenGate Capture for Oracle, exthrr.prm: TCP/IP error 131 (Connection reset by peer). "Googling" for this error, it said that the connection occurred but the host terminated it. Tried to telnet the machine with the used port and it gave the following error: bash-3.00$ telnet 10.10.3.124 7810 Trying 10.10.3.124... Connected to 10.10.3.124. Escape character is '^]'. Connection to 10.10.3.124 closed by foreign host. Here the communication occurs but for only around 3 seconds then it is closed by the host, which is the same explanation of the above error in the goldengate log file. I tried to change the port but still the same error. The problem is happening only when the goldengate process is using the port. When other process is using the same port, I can telnet successfully.

  Read the article

• Change font size for "Default Paragraph Font" in Word

  - by Richard Gadsden

  I have a document where the built-in style "Default Paragraph Font" has been set to a particular size. It shouldn't have a size - it should be inheriting from the paragraph style (that's the whole point of the style). If I go through the user interface, I can't modify this style (the modify button / dropdown is greyed out) While I can work around this in most places, it creates problems for the Table of Contents in particular, as that is forced to be in this style and it overrides the font size from the styles like TOC 1 (etc). I can set the font size through VBA - ActiveDocument.Styles("Default Paragraph Font").Font.size = 10 sets it to ten point, but I can't work out how to reset it back to inherit. At the moment, my table of contents is set to be all in the same size, but really TOC 1 should be bigger than TOC 2. Does anyone have any suggestions for how to fix this? One approach is to use the organizer to copy over the style from a working document, but ideally I'd like a way to resolve the problem without doing that - especially as that's not an easy approach to automate.

  Read the article

• Using GUI ftp on Win7 and Vista without additional software

  - by Stephen Jones

  Goal: provide a 'no-software' method for 'less technical' users to access password protect ftp location from Win7 and Vista (existing approach for WinXP works). 'No software' method to mean without installing additional software (e.g. FileZilla, WinSCP) - the solution is supplied to external non-technical users. WinXP (works): Using Windows Explorer, WinXP supports non-technical ftp access by pasting: ftp://username:[email protected] into the address bar. The remote ftp site's files / directory structure becomes available and can be copied to / from easily (in the style of local file copy / paste) by a 'less technical' user. Win7 / Vista (doesn't work): Pasting the same URL into the Windows Explorer on Win7 or Vista causes an error: An error occurred opening that folder on the FTP server. Make sure you have permission to access that folder. Details: The connection with the server was reset. Notes: a) The same username/password/server typed from the (DOS) command line achieves access to the server, but this is a more 'technical' solution than desired. I am looking for a WinXP equivalent solution. b) Under 'Control Panel' / 'Internet options' / 'Advanced' tab - the boxes for 'Enable FTP folder view' and 'Use Passive FTP' are ticked (enabled) c) Adding an inbound firewall rule for local port 20 (TCP) was attempted with no difference in results (i.e. failure)

  Read the article

• Libvirt / QEmu Machine Fails and Refuses Restart Because of Memory Allocation Errors

  - by Elmar Weber

  I'm having a problem with libvirt. On a system restart all virtual machines (VMs) are started without a problem and keep running. Then at some point in time a set of machines shuts down according to their log. When I try to restart the machine, I'm getting an error that the memory allocation failed, although more than enough memory is free. server ~ # free total used free shared buffers cached Mem: 16176648 16025476 151172 0 285432 950300 -/+ buffers/cache: 14789744 1386904 Swap: 0 0 0 server ~ # virsh start zimbra error: Failed to start domain zimbra error: Unable to read from monitor: Connection reset by peer server ~ # tail -n 4 /var/log/libvirt/qemu/zimbra.log LC_ALL=C PATH=/usr/local/sbin:/usr/local/bin:/usr/bin:/usr/sbin:/sbin:/bin QEMU_AUDIO_DRV=none /usr/bin/kvm -S -M pc-0.12 -enable-kvm -m 3072 -smp 2,sockets=2,cores=1,threads=1 -name zimbra -uuid d05ddb7a-83c4-a77b-d8bc-a322648520cf -nodefconfig -nodefaults -chardev socket,id=charmonitor,path=/var/lib/libvirt/qemu/zimbra.monitor,server,nowait -mon chardev=charmonitor,id=monitor,mode=control -rtc base=utc -no-shutdown -drive file=/var/lib/libvirt/images/zimbra.img,if=none,id=drive-ide0-0-0,format=raw -device ide-drive,bus=ide.0,unit=0,drive=drive-ide0-0-0,id=ide0-0-0,bootindex=1 -netdev tap,fd=19,id=hostnet0 -device rtl8139,netdev=hostnet0,id=net0,mac=52:54:00:21:a9:ad,bus=pci.0,addr=0x3 -chardev pty,id=charserial0 -device isa-serial,chardev=charserial0,id=serial0 -usb -vnc 192.168.1.2:25 -k de -vga cirrus -device virtio-balloon-pci,id=balloon0,bus=pci.0,addr=0x4 char device redirected to /dev/pts/2 Failed to allocate 3221225472 B: Cannot allocate memory 2012-07-06 08:42:56.076+0000: shutting down server ~ # uname -a Linux server 3.2.0-26-generic #41-Ubuntu SMP Thu Jun 14 17:49:24 UTC 2012 x86_64 x86_64 x86_64 GNU/Linux The system is a Ubuntu 12.04 server. The problem seems to occurs since the last restart, which was due to a number of package upgrades and a kernel upgrade. I tried booting with the previous kernel, the problem persists. I was not able to pinpoint an exact event when the machines fail, they do it at nearly the same time. The last time a duplicity job was running, this was not always the case however. Any suggestions on how to debug this? Best regards, elm

  Read the article

• How to diagnose occasional sudden resets?

  - by steve314

  I have a Windows XP system, and have recently upgraded by adding 2 1GB sticks of RAM to the 2x0.5GB already present. Since then, about once per day (the system is used 8+ hours per day), the system has suddenly and unexpectedly reset. On a couple of occasions, the system has frozen completely, only responding to the power button being held in for several seconds to force power off. Nothing at all ever appears in the system event log that might indicate a possible cause - everything seems to suggest business as usual. Sounds like faulty memory - but memtest86+ says otherwise. A full test, taking over an hour, found no issues. The next likely suspicion, then, is that I've knocked something while installing the RAM. Trouble is, everything I can think of to test seems fine. I've opened up the case and prodded a few things around, hoping to get better contact on connections etc, but there's no sign yet as to whether that has made a difference or not. I thought about a malware-related timing fluke, but again, so far as I can tell I'm all clear. All I can think of to add to my checklist (mainly of things that I can't easily check) is... The power supply is (1) only 350W, (2) not necessarily the best quality, and (3) powering a Prescott P4 640 3.2GHz. Could that be borderline overloaded or about to die? How do I check? Is it possible that the CPU isn't getting cooled properly? I haven't had the fan past normal tickover even doing video encoding, and the only sane temperature reading from SpeedFan is pretty steady at 36 celcius, so probably not. Any thoughts? Is there a standard procedure for diagnosing this kind of fault?

  Read the article

• What would cause my Windows machine to seize?

  - by Coltin

  I run Windows XP SP2 on a Desktop I built (I know that doesn't provide much, but I can't say "on a Dell X103938R" or something). It has 'seized' about 7 times in its year and a half life. Everything freezes. I can't move the mouse cursor and the keyboard seems unresponsive. I can turn the monitor on and off and it will hold the last image. The light for the mouse is responsive if I move it. The keyboard lights change when pressed (cap locks, etc). I've waited upto ten minutes for a change, nothing. I haven't connected any activity to the seizing. It's happened when all I was "running" were fullscreen programs (games), just checking email, or once when I was sitting at my desktop (I was reading a book and when I tried to use the mouse, nothing). I've never been able to figure it out. I have to hard reset, and then its fine. It doesn't file system check or anything (not sure if Windows does that). No error when I load up the computer, nothing. If I had uTorrent open, it will have to recheck the torrent files to make sure they weren't corrupted though. (It's not always open when it seizes either). I'm using an AMD Athlon 5400+ with a NVidia GeForce 8600 GT, if that helps. I'm using two hard drives, 500Gb Wester Digital with a 1Tb Hitachi.

  Read the article

• Prevent Win7 from resuming from hibernation

  - by Tigraine

  Hi Guys, I am running Win7 x64 on my machine and everything is perfect. I actually never turn off my PC completely but rather I always put it into hibernation mode for fast resume once I get back. Hibernation works like a charm, but once every 50 or 100 hibernations something goes wrong and the machine reboots. After that I usually have to reset the system clock in BIOS and Windows is starting up from the hibernation image that somehow got saved to disk (that's really cool). But: This hibernation image recovery is awfully slow, once the machine is up again it takes almost 2 minutes for it to not feel sluggish any more (I suspect this is due to pagefaults on all memory access). I'm looking for a way to tell Windows to NOT recover from the crash but rather just boot fresh, discarding the hibernation since it's faster to just reboot rather than wait for 3+ minutes for the machine to get it's act together. I do see the normal bios startup and also the windows boot afterwards, but hitting F8 like crazy doesn't do anything. In Win2000 and XP a Menu would come up asking me how I do want to boot, but I can't find it on Win7. Thanks in advance!

  Read the article

• How do I disable the firewall on blackberry?

  - by user15660

  I own a Blackberry 9630 tour.(Sprint). The firewall is enabled with a lock sign and grayed out. I'm not able to disable it. Because of this many of my blackberry apps don't work as it gives a message "The application has tried to open a connection that's not allowed by your IT policy". I tried all options and there's nothing to disable. This is a personal blackberry and I don't have an IT policy on it. I did all methods like wiping, formatting/resetting to factory settings acc. to blackberry site by running their reset app from PC etc etc. but nothing works I tried CrackUtil for blackberry and that worked and wiped the blackberry. I restored my bb and started using it just to notice that the firewall is enabled back after a desktop manager connection to PC. I even made sure the policy.bin file on PC is a regular one with no IT policy. How do I get this disabled? I had the same problem on my old blackberry 8330 and crackutil disabled the firewall. but after a few days after a desktop manager update of blackberry OS and other small stuff the firewall got enabled again. Please give me a solutions to disable the firewall on blackberry

  Read the article

• Destroyed user account on OS X with dscl; how to restore? [migrated]

  - by Sam Ritchie

  I was trying to create a new user on my OS X Lion machine, and somehow managed to destroy my own user's account. Here are the steps I took; hopefully someone here can recognize what I did, and maybe identify some way around this. First, I ran these commands: sudo dscl localhost -create /Local/Default/Users/elasticsearch sudo dscl localhost -create /Local/Default/Users/elasticsearch /bin/bash # mistake! sudo dscl localhost -create /Local/Default/Users/elasticsearch UserShell /bin/bash sudo dscl localhost -create /Local/Default/Users/elasticsearch RealName "Elastic Search" sudo dscl localhost -create /Local/Default/Users/elasticsearch UniqueID 503 # MY uniqueID sudo dscl localhost -create /Local/Default/Users/elasticsearch PrimaryGroupID 1000 sudo dscl localhost -create /Local/Default/Users/elasticsearch NFSHomeDirectory /Local/Users/elasticsearch The big mistake I made here was using "503", which was my user's UniqueID. Immediately my shell username changed to "elasticsearch". I fiddled around, tried to change the current user with sudo su -u sritchie, but this didn't work. On restart, only the "Elastic Search" user was available. I logged into the Lion Recovery partition and reset the root password. After logging in as root and checking on the terminal, I made the remarkable discovery that my home folder was totally empty. I deleted the elasticsearch user, but it made no difference. I don't see anything in Deleted Users either. The odd thing is that when I log in now as myself (sritchie) I can see desktop icons with previews. I can even open a few text files from the Downloads folder if I use the dock alias to Downloads. Could this data be hiding somewhere? Any help would be REALLY appreciated! Thanks, Sam

  Read the article

• NGINX server_name issues

  - by Unai

  I have the following simple server block on NGINX: server { listen 80; listen 8090; server_name domain.com; autoindex on; root /home/docroot; location ~ \.php$ { include /usr/local/nginx/conf/fastcgi_params; fastcgi_index index.php; fastcgi_param SCRIPT_FILENAME /home/docroot$fastcgi_script_name; fastcgi_pass 127.0.0.1:9000; } } After I include the relevant settings on my hosts file I get the following (unexpected) behavior: http: //domain.com/ and http: //domain.com:8090/ work fine; http: //domain.com:8090/future-cell-phone-technology-01-150x150.jpg works; http: //domain.com/future-cell-phone-technology-01-150x150.jpg - ERROR! "The connection was reset" (note.- added a space after http: to avoid link protection but this is not really promoting anything) I've been troubleshooting (3) for a couple hours and I'm unable to identify the culprit. I'm running NGINX 1.0.10 (latest stable) on Debian 6.0.2 32 bits. This NGINX instance runs another 40 or 50 sites with no problems.

  Read the article

• PHP crashing during oAuth scripts

  - by FunkyChicken

  I just installed Nginx 1.2.4 and PHP 5.4.0 (from svn) (php fpm). CentOs 5.8 64 The problem I have is that PHP crashes the moment I run any social oAuth scripts. I have tried to log into Facebook, Twitter and Google with various scripts that I know work on my other servers. When I load the scripts I get a 502 error from Nginx. And I find these errors in the log: in php-fpm log: WARNING: [pool www] child 23821 exited on signal 11 (SIGSEGV) after 1132.862984 seconds from start in nginx log: ERROR: recv() failed (104: Connection reset by peer) while reading response header from upstream From what I can see, it goes wrong when PHP tries to make a request to any of the oAuth servers. https://github.com/mahmudahsan/PHP-SDK-3.0---Graph-API-base-Facebook-Connect-Tutorial-Source for example is one of the scripts that works perfectly on my other machines, but causes PHP to crash. I found: http://stackoverflow.com/questions/3616191/nginx-php-fpm-502-bad-gateway which seems to be a similar problem, but I cannot find a way to solve it. +++ UPDATE +++ Now I have been doing some debugging in 1 of the scripts that is playing up. If you go to line 808 http://pastebin.com/gSnzRtXb it runs the curl_exec() command. When that is ran, it crashes. If i echo'test';exit; just above that line, it echo's correctly, if i do it below that line, php crashes. Which means it's that line 808 which causes the crash. So I made a very simple script to do some testing: http://pastebin.com/Rshnyhcm which also uses curl_exec, but that runs just fine. So I started to dig deeper into that query from the facebook script to see what values the $opts array contains from line 806. Output of that array is: http://pastebin.com/Cq9ffd3R What the problem is, I still have no clue :(

  Read the article

• MOSS2007 tries to use ActiveDirectory when I have configured an alternative membership provider

  - by glenatron

  I've got a MOSS site that I am trying to configure using Forms authentication and absolutely any kind of membership provider whatsoever. Thus far ActiveDirectory has proved obstructively difficult so I've just whipped up a simple stub membership provider and put it in the GAC. It's a very basic and simple provider but it works fine with an ASP.Net site, I just can't make it work with Sharepoint. On Sharepoint I get the following error when I look for StubProvider:Bob ( or anything else for that matter) from the "Policy For Web Application" people picker: Error in searching user 'StubProvider:bob' : System.ComponentModel.Win32Exception: Unable to contact the global catalog server at Microsoft.SharePoint.Utilities.SPActiveDirectoryDomain.GetDirectorySearcher() at Microsoft.SharePoint.WebControls.PeopleEditor.SearchFromGC(SPActiveDirectoryDomain domain, String strFilter, String[] rgstrProp, Int32 nTimeout, Int32 nSizeLimit, SPUserCollection spUsers, ArrayList& rgResults) at Microsoft.SharePoint.Utilities.SPUserUtility.SearchAgainstAD(String input, SPActiveDirectoryDomain domainController, SPPrincipalType scopes, SPUserCollection usersContainer, Int32 maxCount, String customQuery, TimeSpan searchTimeout, Boolean& reachMaxCount) at Microsoft.SharePoint.Utilities.SPActiveDirectoryPrincipalResolver.SearchPrincipals(String input, SPPrincipalType scopes, SPPrincipalSource sources, SPUserCollection usersContainer, Int32 maxCount, Boolean& reachMaxCount) at Microsoft.SharePoint.Utilities.SPUtility.SearchPrincipalFromResolvers(List`1 resolvers, String input, SPPrincipalType scopes, SPPrincipalSource sources, SPUserCollection usersContainer, Int32 maxCount, Boolean& reachMaxCount, Dictionary`2 usersDict). The Provider is named as Authentication Provider for the Site Collection in question. As far as I can tell this is because Sharepoint is still trying to access ActiveDirectory rather than talking to the provider I'm asking it to use. My Sharepoint Central Administration section includes this: <membership> <providers> <add name="StubProvider" type="StubMembershipProvider.Provider, StubMembershipProvider, Version=1.0.0.0, Culture=neutral, PublicKeyToken=5bd7e2498c3e1a03" /> </providers> </membership> And also: <PeoplePickerWildcards> <clear /> <add key="StubProvider" value="%" /> </PeoplePickerWildcards> Is there a clear reason why this would not be accessible from the PeoplePicker or why it is still trying to use ActiveDirectory? I've made sure I reset IIS and even restarted the server to see if either of those helped but they made no difference.

  Read the article

• Best way to execute a command after Linux system halt

  - by Lukas Loesche

  Problem: The SSDs in our servers require a power cycle (i.e. off/on, not reset/warm reboot) after a firmware update. Thoughts: Using 'ipmitool chassis power cycle' I can cycle the server's power. However this would cut the power while the system is still running, filesystems are mounted, etc. What I basically want is a delayed power cycle so the system has a change to halt. But I guess that would have to be implemented on the server's IPMI board, so it's not really an option. My initial idea was to dynamically create a ramdisk containing the tool and libs and somehow integrate that into the halt process. I saw there's a /etc/init.d/halt, so that would be my starting point. Although I believe the kernel at some point in the shutdown process starts to kill off remaining processes. So I'm not even sure if that's a viable way. Question: What would be the best way to execute ipmitool (or any other command), after the system has halted and all regular filesystems are unmounted?

  Read the article

• How to configure networking on an appliance such that it can plug and play on any corporate network?

  - by Joshua Lim

  I had a chance to configure a Moxa NPort device server appliance on my client's network, it was very easy to do so, done in just 2 minutes. Here's what I did:- The Moxa device server had a preset IP address of 192.168.127.254 and subnet mask 255.255.255.0 - http://www.moxa.com/doc/manual/nport/5400/NPort_5400_Series_Users_Manual_v4.pdf Moxa provides a Windows software which I used to "scan" for the device server. It worked like magic! The software returns a list of device servers found. Each device server is identified by MAC address, and by selecting the device server using the software, I can reset the default IP address and subnet mask of that device server! In comparison, during an earlier project, I spent 2 hours trying to get KVM to work for a Windows 7 embedded appliance I'm trying to install in my client's network - http://superuser.com/questions/380305/how-to-configure-windows-7-professional-appliance-pc-on-my-clients-network-usin Prior to that, I have already tried pre-configuring the IP address and subnet mask to the one which my client provided, yet the appliance still can't connect to the client's network! I've also tried cross cable, didn't work either. After KVM worked, I discovered that the network settings were "lost" after I plug the machine into the client's network. Now my question is what can I do to setup my Windows 7 embedded appliance so that it can connect to any network like that the Moxa device server? I tried experimenting this on my network using a Windows machine configured to an IP address of 192.168.127.254 and subnet mask 255.255.255.0, but it doesn't connect to my network that uses 192.168.0.*. :( EDIT: I would like to point out that the Moxa Windows configuration software seems to be able to connect to any Moxa device connected to the network even if it is on a different subnet, as long as the network adapter shows "connected". This is important because the Moxa device has no VGSM port or interface to configure the IP address.

  Read the article

• Domain Controller died, now get authentication boxes in IE for SDL Tridion 2009

  - by Rob Stevenson-Leggett

  We had a major network issue where our secondary domain controller (responsible for Win2k3 boxes) died and had to be rebuilt (I beleive this is what happened, I am a developer not network admin). Anyway, I am working remotely via VPN at the moment and since this happened, I am getting an authentication box when trying to access certain areas of SDL Tridion via IE (Tridion 2009 SP1 is IE only) it seems like somewhere my credentials are not being passed correctly or the ones cached on my laptop do not match the ones the Domain Controller has. This only seems to affect Windows 2003 servers. Our IT support thinks that the only way to sort it out is to connect my laptop directly to the network. I am not planned to go to the office for a few weeks at least and this issue means I have to work with Tridion via Remote Desktop. We thought changing the password on my account might work but this didn't help. So basically my question is, is there any way I can reset my credential cache without having to reconnect to the network? Or is it IE that is causing the problem perhaps, since I can RDP to servers and use Tridion 2011 instances in other browsers fine? I am on Windows 7 using SonicWall VPN client.

  Read the article

• router only assigns small number of IPs

  - by Liam Coates

  Been having a problem with my router for a while now, might just be because it is really old but here's the problem: If a lot of computers are connected to my home network someone will get disconnected. They are assigned IPs and it seems like at a certain point (and I don't know how many) you either get assigned the same IP as someone else or something else is happening and you get disconnected - until i soft reset it and it works again which takes 30 secs. I'd say my tablet, my PC, my sisters iPad, 2 laptops and a netbook is the most that can be connected at one time so that is 6 but that should be fine. The only way I know this is the problem is because I turned on my tablet and I was online on my PC, got disconnected but my tablet was still connected, this is just after i turned the tablet on so I know my router is having difficulty with IPs, it is like it assigned the same IP to the tablet which then clashed with my desktop and knocked me off. I see that sometimes the following solves it as well so I wrote a batch file with a menu to execute these commands as I have to do it so often. ipconfig /release ipconfig /flushdns ipconfig /renew Any ideas? Or shall I just get a new router as this one is old and maybe can't handle giving out that many IPs? Cheers!

  Read the article

• How to reinstall Windows Boot Manager on EFI partition

  - by joaocandre

  So I've been trying to install Ubuntu on a second HDD on my desktop, which has W8 installed on a SSD (UEFI-only boot). Thing is, during Ubuntu installation I made the mistake of choosing to install the bootloader (GRUB) to the first disk (the SSD), and after install I could not boot into W8 (the entries in GRUB didn't work). Following these instructions, I managed to be able to get "Windows Boot Manager" back, however I lost GRUB in the process, and got a duplicate "Windows Boot Manager" entry in BIOS, along with the "Ubuntu" entry, which then I used to boot into Ubuntu. Later, I decided to reinstall Ubuntu, and formatted the HDD from within windows, however, the entries in BIOS stayed the same, and, while I had the HDD connected to the motherboard, I could not boot into an Ubuntu Live USB (in order to reinstall Ubuntu). I made another mistake by updating the BIOS, which cleared all of the EFI boot entries in BIOS, and, right now, I get an error when boot from the SSD: grub: device not found (...) So it seems that grub is still installed in the EFI partition of the SSD, and since I don't have the WBM entry in BIOS anymore, I cannot even boot into Windows, and the previous instructions don't work anymore. Is there another way to reset W8 EFI partition to the default?

  Read the article

• Is Gmail Being Blocked by my ISP (wait till you read this)?

  - by James

  This is the strangest thing I have ever encountered. I have a desktop on which I cannot access Gmail and also youtube sign in (I believe since youtube is owned by google they both use the same sign in system). So okay, maybe my ISP is blocking these for some reason or maybe my firewall is, or maybe there is something wrong with my connectivity, right? NO. On other computers that uses the same connection via a wireless router I can access both gmail and youtube sign in just fine. On this computer which doesn't have a wireless card and so I have to connect via Ethernet cable (connected to a USB converter since the Ethernet port doesn't work anymore) I can access all sites and services including things like aol and hotmail. But only when it comes to gmail, do I get complete and utter throttling. I even turned off my AV ad Firewall momentarily and no luck. The gmail ages starts to load and by mid point it just stays there loading and loading and loading... never ends. I tried everything, I reset the modem and router multiple times. I reinstalled my operating system from a vista to a windows 7 hoping a complete reinstall would solve the issue, but no luck. So can anyone for the life of them figure out why this could be? And yes, I am going to call my ISP but not to solve this issue, but to cancel them. I want to upgrade to cabel from DSL anyway. I didn't mention my ISP because I'm not sure if that is within the rules (if it's okay some one let me know and I will). P.S. All this happened one day, before gmail was perfectly accessible in this computer. I can't remember anything special that happened on that day prior to this. The only thing I can think of is, my ISP or Google itself is blocking this computer based on it's mac address, but I don't know if that's even done. Additional info: PC: Windows 7 Ultimate 32 bit Connection Type: DSL Connecting Medium: Ethernet cable via USB converter

  Read the article

• What could cause TFTP reloaded Cisco `running-config` on 871 to fail?

  - by xtian

  Cisco CCP Write Configuration borked my 871w config while I was trying to setup port forwarding. I went through the basic steps to reconfig the router. I looked to see if I could just reset the router. Nope. I tested the 871's flash memory with fsck to see if there was hardware failure. Nope. Then I rewrote the minimal config for TFTP (which is the same for Cisco's CCP app.). Thne, I successfully uploaded a previously working running-config from Win Vista using SolarWinds TFTP Server, unfortunately the restore was not entirely successful. The old running config was saved to the 871's startup-config and I can login using console port. Some other things that are working are the hostname and welcome message but that's about it. Startup shows an error SETUP: new interface NVI0 placed in "shutdown" state after tftp. The missing light on the access point modem for ethernet link show the 871'a outside FE4 is not working. SO...what's the possible problem with reloading a previously working config (approximately 4 months with the same config) via TFTP? Is there something I can look for on the 871 to verify the config? Or on Vista to validate the config file itself before I transfer it? Or, is this there a common TFTP issue? UPDATE. I missed the instruction from Cisco's TFTP page to delete aaa lines from the config (although a video from a SuperUser user didn't make this point in his most excellent demo). There were several lines of this sort, I deleted them and uploaded again. However, they're back. I assume they're added automatically? [nope, see answer] UPDATE 2. The reload of previous settings was successful, but this error remains. I don't even know now if it was there before or not. It seems irrelevant to the question.

  Read the article

• Office 2010 Trusted Locations not working after restart

  - by Josh King

  In Excel 2010, on Windows XP, I am unable to open files - through the open dialog box - from a network drive. The sever has already been added to the Trusted Locations and now most security settings turned down or off. Excel will show "Downloading ..." on that status bar and a progress bar which doesn't progress. We have left Excel sitting in this state for 30+ minutes and no change. A similar problem occurs when saving files to network shares. If we use explorer to navigate to the files and double click them they open flawlessly. No add-ins are active. We also have this problem in Word 2010, but the server was not initially in the Trusted Locations. I added it and it worked until the PC was reset, it now exhibits the same issues as Excel where the server is in the Trusted locations but will not open files. I have tried removing the server from the Trusted Location in both applications, restarting the PC and re-adding them (testing before, after and in-between) and had no luck.

  Read the article

• Wireless to Wireless Transfer Slow on a Linksys WRT54GL

  - by Kyle Brandt

  The Situation: When I try to transfer a file from one computer to another that are both connected via wireless on a WRT54GL (in a office) with dd-wrt firmware I often get bad speeds. In generally they average around 100 kilobytes a second. Either computer can download via wireless from the Internet at at about 2 megabytes a second. The speed is slow with the transfer of one large file. There are about 20 other wireless networks that the computers can see, so there is a lot of noise, but I don't have the equipment to really monitor the frequencies well. But that still seems pretty slow. I thought maybe it was the transmit on each card, but even when they are 5 feet away with a line of sight I still get these speeds. According to Linux both cards are operating at 54g. My Questions: Is this normal for this sort of consumer level wireless equipment? Anything I can do to improve it? why is wireless to wireless transfer slow when everything else isn't? Whats steps might I take to figure out what is happening? For example, are lots of packets not making to the access point requiring retransmissions? Above all, I want to find out what the problem actually is. This may seem odd, but at this point I am more interested in understanding what the problem is than fixing it. What I have tried: I have tried messing with lots of settings. Different channels, xmit power, G-Only, none of which has made anything any better. I've also tried upgrading to newer dd-wrt firmware version and doing a reset to wipe out the settings.

  Read the article

• Monitoring whether Google Apps email address is reachable

  - by Acorn

  Backstory: I bungled things a bit the other day, and inadvertantly deleted the DNS overrides for my domain including the MX records that point to Google Apps, causing 2 days of lost emails. What I want: I want to be able to monitor the email address/account so that I can be alerted if for any reason something has gone wrong and emails aren't arriving. Thoughts: I was thinking there might be a way to test the email without having to send an actual message. Does this exist? This wouldn't help if the DNS has reset itself to a different mailserver would it? The other idea was sending periodic emails to check the address it working. How would you automate this? You'd need to somehow check that the email address had arrived as well as checking if it had bounced. Are there any scripts that exist that would do something like this? What would be the best method? Maybe a combination of checking that the MX records for the domain are set to what they're supposed to be set to, and sending automatic test emails to check that things are still functioning on the Google Apps end?

  Read the article

• Ubuntu Laptop as a wireless hotspot on bridge mode

  - by nixnotwin

  I have a wired router to which my ubuntu laptop connects via ethernet. The wierless NIC of the laptop acts as a wireless hotspot on master mode. I use hostapd fo this. I have bridged eth0 and wlan0, so my wireless clients that connect to my laptop over wifi get ip from the wired router via dhcp, so the devices get registered at the wired router ( and the laptop is just an access point). I use the following commands to get my laptop+accesspoint working: sudo brctl addbr br0 sudo brctl addif br0 eth0 sudo hostapd /etc/hostapd/hostapd.conf & sudo dhclient -d br0 & sudo ifconfig wlan0 192.168.1.15 netmask 255.255.255.0 up sudo brctl addif br0 wlan0 These commands enable me to access internet on my wireless clients and also on the laptop which is acting as wireless accesspoint. But if I reboot the wired router (without rebooting the laptop that is acting as accesspoint), Internet access on the laptop+accesspoint gets lost, but on wireless clients it works fine. Even I have not been able to figure out a command which will reset the laptop interfaces to default settings, so everytime the router reboots, I have to reboot the laptop too to get into default settings so that I can re-enter the above mentioned commands. My first question is How can I have my bridge+accesspoint up and running even-though the router reboots? And is there a command to set the interfaces to a default state? (ifdown -a doesn't work, after issuing the command the bridge still remained).

  Read the article

• Ubuntu Laptop as a wireless hotspot on bridge mode

  - by nixnotwin

  I have a wired router to which my ubuntu laptop connects via ethernet. The wierless NIC of the laptop acts as a wireless hotspot on master mode. I use hostapd fo this. I have bridged eth0 and wlan0, so my wireless clients that connect to my laptop over wifi get ip from the wired router via dhcp, so the devices get registered at the wired router ( and the laptop is just an access point). I use the following commands to get my laptop+accesspoint working: sudo brctl addbr br0 sudo brctl addif br0 eth0 sudo hostapd /etc/hostapd/hostapd.conf & sudo dhclient -d br0 & sudo ifconfig wlan0 192.168.1.15 netmask 255.255.255.0 up sudo brctl addif br0 wlan0 These commands enable me to access internet on my wireless clients and also on the laptop which is acting as wireless accesspoint. But if I reboot the wired router (without rebooting the laptop that is acting as accesspoint), Internet access on the laptop+accesspoint gets lost, but on wireless clients it works fine. Even I have not been able to figure out a command which will reset the laptop interfaces to default settings, so everytime the router reboots, I have to reboot the laptop too to get into default settings so that I can re-enter the above mentioned commands. My first question is How can I have my bridge+accesspoint up and running even-though the router reboots? And is there a command to set the interfaces to a default state? (ifdown -a doesn't work, after issuing the command the bridge still remained).

  Read the article

• Dell 2970 - HP 1/8 G2 autoloader keeps falling off LSI 2032 SCSI chain

  - by middaparka

  I've a somewhat irritating problem with a Dell 2970 that has a HP 1/8 G2 autoloader (the Ultrium LTO 2 model) attached to the Dell/LSI 2032 non-RAID SCSI card. In essence, sometimes the autoloader/drive completely fails to appear on the SCSI chain (i.e.: there's neither a media changer or tape drive present within the device manager) and sometimes it appears but then subsequently disappears at a seemingly random (yet always inconvenient) time, resulting in backup failures. On most occasions, there are simply no errors logged in the system event log, but I did manage to capture a series of LSI_SCSI event ID 11 ("The driver detected a controller error on \Device\RaidPort0") errors followed by an event ID 129, ("Reset to device, \Device\RaidPort0, was issued") error during testing. I've tried two different cables, both with the same effect – sometimes the autoloader appears (for a while), sometimes it's completely absent. There's only one terminator I've tried to use, but as I've since successfully tested the autoloader on multiple occasions (albeit via a Adaptec U160 card on a different machine), my gut feel is that the issue doesn't lie with the terminator, or indeed the autoloader itself. As such, I'm just wondering if anyone has any ideas? It's most likely not relevant, but this is all under Windows SBS 2008, running Backup Exec 12.5 SBS edition (the Dell version), both fully patched. Addidtionally, the autoloader is running the latest firmware. It's been a while since I've dealt with anything SCSI, so all suggestions will be gratefully, gratefully received.

  Read the article

< Previous Page | 204 205 206 207 208 209 210 211 212 213 214 215  | Next Page >