Search Results

Search found 6376 results on 256 pages for 'git reset'.

Page 209/256 | < Previous Page | 205 206 207 208 209 210 211 212 213 214 215 216  | Next Page >

• Disc drive busy on MacBook, with disc stuck inside.

  - by ayaz

  I have a white MacBook, running Snow Leopard, 10.6.3 with the latest updates. I popped in a DVD that the system failed to mount. I did not see any conspicuous errors. As a result of this failure, the DVD got stuck in the drive. Neither pressing the eject button on the keyboard nor running the diskutil eject command caused the DVD to come out. The commands drutil eject and drutil tray open could not get the DVD to budge at all. The 'mount' and 'eject' buttons on the window for Disk Utility are dimmed out, while it is written in the middle for the DVD drive that that particular disc drive is busy. This is not the first time this has happened with me. I know that I will ultimately have to resort to rebooting the system and holding down the eject button to get the DVD to come out. But, is there any workaround that does not involve rebooting the system and prying the disc out? The drive on this MacBook does not have a needle-pin reset button -- at least, I couldn't find it anywhere. Any help will be greatly appreciated. Many thanks.

  Read the article

• Find the IP of the router between me and main router/gateway?

  - by Crash893

  I have a Netgear router that is the main router/gateway in and out of the network. Then I have a Linksys 54g router with WiFi that we use as are main WiFi access point The Cat5 runs from the router to the WiFi routers LAN port (not WAN). And then if you connect to that WAP you are basically on the network. I want to be able to find out what the IP address of that WAP is but so far I can't figure out how to: I've tried doing a tracert to the gateway IP but I get nothing. I've scanned all the IP addressed in the network. I've gone to the Netgear main router and looked under attached devices but it doesn't say anything. Any ideas on how I can figure out how to administer it? (I do have limited physical access but my attempt to plug into it came back with a faulty IP (in the 169 range where the rest of the office is 192.168...). I never set this router up to begin with so I'm reluctant to just kill it with the reset button because I can't get into see what the settings are set to.

  Read the article

• Set postfix to send email but not to receive them

  - by CodeShining

  I'm using Google Apps to handle personal email addresses for my domain name, and I set up the DNS as Google suggests. All works fine. Now since I need a SMTP to send emails from my e-commerce I installed Postfix on the server. It works fine when I send emails to any email address but it doesn't send to the same domain name, so let's say my domain is example.com, I set postfix using example.com, if I try to reset a password using [email protected] postfix doesn't send and instead reports on the mail.log Sep 20 01:09:52 ip-10-54-26-162 postfix/pickup[6809]: B09A3415D8: uid=33 from=<www-data> Sep 20 01:09:52 ip-10-54-26-162 postfix/cleanup[6854]: B09A3415D8: message-id=<20120920010952.B09A3415D8@ip-10-54-26-162.eu-west-1.compute.internal> Sep 20 01:09:52 ip-10-54-26-162 postfix/qmgr[30978]: B09A3415D8: from=<[email protected]>, size=4234, nrcpt=1 (queue active) Sep 20 01:09:52 ip-10-54-26-162 postfix/local[6856]: B09A3415D8: to=<[email protected]>, relay=local, delay=0.01, delays=0.01/0/0/0, dsn=5.1.1, status=bounced (unknown user: "myaccount") Of course it cannot find a local user "myaccount" since that account is on Google Apps... How can I tell Postfix to send the email and do not search for a local user?

  Read the article

• Hyper-v on 2012R2 startup gen1 vm causes the host to freeze up

  - by sputnik

  I've searched a lot to resolve the following issue, but nothing helped me. My problem is, that starting up a first-gen vm locks up the whole host. Only a hard reset helps. Second-gen vm starts and runs perfectly. The freezes happened on 3 different vms. FreeBSD, Ubuntu, Windows Server 2008R2, while Windows 8.1 on second gen config works perfectly. Im using this pc mainly as a workstation. No eventlog errors nor dumps are generated. My system: Windows Server 2012R2 FX-8350, non OC ASRock 870 Extreme R2 (Crappy board imho) 32GB DDR3 1866@1600 (My motherboard, against the "support" for 1866ram won't work with full speed) 120GB SSD 4.5TB Storage space device I dont think that its due to my system, because vmware workstation was running without problems. Did I forget to configure something? Any help is appreciated. P.S: Even deactivating C1E, C6, C&Q didnt work. P.P.S: With no virtual network adapter set, the system still locks up. Creating a first gen vm without any hdds and network and launching works. Attaching a boot dvd causes the host to freeze. The host freezes as the gen1 vm begins to boot, doesn't matter if from dvd or hdd

  Read the article

• IIS SSL is taking all IPs although it is told not to

  - by Martin Sall

  I have a testing system where IIS Express on Windows 7 SSL website has to live together with Cerberus FTP server SSL website (Cerberus FTP has a built-in web server for HTTP uploads). I have set up Windows to use two IPs from my router 192.168.1.128 (for IIS SSL Web Site, using a self-generated SSL certificate for now) 192.168.1.129 (for Cerberus FTP built-in SSL Web Site) In IIS I have set web site binding to use only the IP 192.168.1.128. But still when I launch Cerberus, it says - cannot bind 192.168.1.129:443. I tested in Firefox - indeed, when I go to 192.168.1.129 (or even localhost), I do not get “Unable to connect“ page as expected, but “The connection was reset” instead. IIS is still occupying those IPs, although it is not serving the website on those IPs. When I stop the IIS website, Cerberus FTP Website launches without problems. But then I cannot launch IIS web site, it tells - "The process cannot access the file because it is being used by another process". Why is IIS SSL web site still occupying all IPs?

  Read the article

• Moving a lotus database causes incoming mail failure

  - by Logman

  Hey all, I moved a couple lotus note databases to another hd (ran out of space) by using a directory link/pointer on the domino server. USed a text file with the .DIR ext with the desired new path etc... well that works fine. I open up a lotus notes client, use the id and then OPEN the database. The directory link works fine, the new location of the db is opened with no problems. We found out that we couldnt FORWARD any mail: We did the following to make it work: Goto menu FILE|MOBILE|EDIT CURRENT LOCATION Goto tab MAIL and enter the correct path for "Mail File:" example: it should read "mail\morespace\flabor" and not "mail\flabor" "morespace" = directory link/pointer we can forward and reply to emails fine after that fix. The problem is that the user has no incoming email. Domino is still trying to send the incoming mail of that user to its old db location "mail\flabor" instead of "mail\morespace\flabor". Delivery error saying user does not exist. Is this a cache problem? We have reset the server ("Q" at the prompt), though we have not completely shut it down though. Thanks Frank

  Read the article

• What to do with a broken OS X install disc?

  - by slhck

  First things first: I don't appreciate software piracy and I really want to spend money on software that I use and that I work and make money with. I don't want this question closed just because I consider downloading software, I only want honest opinions and alternatives. Here we go: So I have my OS X Snow Leopard Upgrade DVD, but it's horribly scratched and won't boot anymore. It endlessly loads and at some point I have to force pull it out of the disc slot. How can I reset my Mac then? Can I take my original disk to an Apple Store and ask them for a replacement? Will they believe me, even if I don't have the receipt anymore? Would owning the original disk make it okay for me to look somewhere on the internet and download it? I don't even know if that will work without hassles. Could I try to read the disk to an image with some error correction methods? Maybe during boot it can't read some files, but some other program can? Is there any other way of resetting the Mac? Mine's now over 3 years old an I seem to have misplaced my original discs that had 10.4 on it. Or should I just buy a new 10.6 upgrade disk? (Which is not really what I want to do) Answers and opinions would be much appreciated.

  Read the article

• Postfix misconfigured? 550 Sender rejected from recieving server

  - by wnstnsmth

  We use Postfix on our CentOS 6 machine, having the following configuration. We use PHP's mail() function to send rudimentary password reset emails, but there is a problem. As you will see, mydomain and myhostname is correctly set, afaik. alias_database = hash:/etc/aliases alias_maps = hash:/etc/aliases command_directory = /usr/sbin config_directory = /etc/postfix daemon_directory = /usr/libexec/postfix data_directory = /var/lib/postfix debug_peer_level = 2 html_directory = no inet_interfaces = localhost inet_protocols = all mail_owner = postfix mailq_path = /usr/bin/mailq.postfix manpage_directory = /usr/share/man mydestination = $myhostname, localhost.$mydomain, localhost mydomain = ***.ch myhostname = test.***.ch newaliases_path = /usr/bin/newaliases.postfix queue_directory = /var/spool/postfix readme_directory = /usr/share/doc/postfix-2.6.6/README_FILES sample_directory = /usr/share/doc/postfix-2.6.6/samples sendmail_path = /usr/sbin/sendmail.postfix setgid_group = postdrop unknown_local_recipient_reject_code = 550 Now this is the stuff that is in the /var/log/maillog of Postfix upon sending an email to ***.***@***.ch, with ***.ch being the same domain our sending server test.***.ch is on: Dec 13 16:55:06 R12X0210 postfix/pickup[6831]: E6D6311406AB: uid=48 from=<apache> Dec 13 16:55:06 R12X0210 postfix/cleanup[6839]: E6D6311406AB: message-id=<20121213155506.E6D6311406AB@test.***.ch> Dec 13 16:55:07 R12X0210 postfix/qmgr[6832]: E6D6311406AB: from=<apache@test.***.ch>, size=1276, nrcpt=1 (queue active) Dec 13 16:55:52 R12X0210 postfix/smtp[6841]: E6D6311406AB: to=<***.***@***.ch>, relay=mail.***.ch[**.**.249.3]:25, delay=46, delays=0.18/0/21/24, dsn=5.0.0, status=bounced (host mail.***.ch[**.**.249.3] said: 550 Sender Rejected (in reply to RCPT TO command)) Dec 13 16:55:52 R12X0210 postfix/cleanup[6839]: 8562C11406AC: message-id=<20121213155552.8562C11406AC@test.***.ch> Dec 13 16:55:52 R12X0210 postfix/bounce[6848]: E6D6311406AB: sender non-delivery notification: 8562C11406AC Dec 13 16:55:52 R12X0210 postfix/qmgr[6832]: 8562C11406AC: from=<>, size=3065, nrcpt=1 (queue active) Dec 13 16:55:52 R12X0210 postfix/qmgr[6832]: E6D6311406AB: removed Dec 13 16:55:52 R12X0210 postfix/local[6850]: 8562C11406AC: to=<root@test.***.ch>, orig_to=<apache@test.***.ch>, relay=local, delay=0.13, delays=0.07/0/0/0.05, dsn=2.0.0, status=sent (delivered to mailbox) Dec 13 16:55:52 R12X0210 postfix/qmgr[6832]: 8562C11406AC: removed So the receiving server rejects the sender (line 4 of log output). We have tested it with one other recipient and it worked, so this problem might be completely unrelated to our settings, but related to the recipient. Still, with this question, I want to make sure we're not making an obvious misconfiguration on our side.

  Read the article

• MySQL Master - Master Broken

  - by Recc

  I've Inherited a Mysql master master system, I've noticed the second master (lets call it slave from now on as it's running on a 'slave' machine) stopped getting its db's updated. I saw that Master: Slave_IO_Running: Yes Slave_SQL_Running: Yes Slave: (with an error I truncated) Slave_IO_Running: Yes Slave_SQL_Running: No Last_Errno: 1062 Last_Error: Error 'Duplicate entry '3' for key 'PRIMARY'' on [...] I don't know what caused it to process considering we cant get duplicate there. What's important is to resume normal operations; Right now I've stop slave; on the Master and stop slave; on the Slave because I saw that if I change records on the Slave the changes Do Get Propagated to Master which is in active use. How do I: Force sync EVERYTHING from master to slave without affecting data on master? Then hopefully have slave pickup replication as usual? UPDATE OK I Tried deleting all tables on slave then it complained in that error section that the 'table' doesnt exist. So i made a no data dump of Master, and made sure I have only empty tables in Secondary (slave). I start slave; on slave BUT now it's complaining about bloody alter table statements for instance: Last_Errno: 1060 Last_Error: Error 'Duplicate column name [...] Query: 'ALTER TABLE [...] How to skip the fracking alter statements I just want to replicate the bloody data and be done with it, my tables have the lates changes already FFS and now its complaining about changes made after the replication seized weeks ago How do I reset the log or something? OUTSTANDING Why would this start happening? The "Secondary" is propagating to "Primary". "Primary" is not propagating to "Secondary". But any fixes I tried to do left it in the same state Yes-Yes Yes-No with same Last_Error. I think around that time the server was taken off the network, could that confuse MySQL in some way?

  Read the article

• Why would my wireless cut in and out every minute or so?

  - by Strilanc

  I've been having problems with my wireless. I moved to a new apartment, and the wireless seems incredibly unreliable. Sometimes it will be stable for hours until, all of a sudden, it starts cutting in and out. I'll get 30-90 seconds of normal behavior, then 5-30 seconds of nothing, then repeat. Sometimes the connection will stop working entirely, until I power-cycle the router. It is extremely, extremely annoying. Surfing the web isn't too bad, assuming you can stand the random 5-30 second waits. But some connections are sensitive enough to timeout, and it certainly makes multiplayer games unplayable. Facts: I confirmed the problem using ping google.com -t. I get normal traffic, interspersed with bursts of "Request timed out.". I've never had this problem before with this laptop. I didn't bring my own router or modem to the apartment. I'm using what the old tenant had. Hooking directly to the modem via an ethernet cable results in a stable connection. Temporarily cutting power to the router sometimes fixes the problem. Sometimes it doesn't. I reset the router, but the problem remained. Apparently the previous tenant had issues with the internet, but I don't know what they were specifically. The router is a D-Link DIR-615, and their tech support is useless.

  Read the article

• Terrible noises from subwoofer of ACER Aspire 6930 with Realtek sound chip

  - by OneWorld

  After approximately 5-15 min of listening to music my subwoofer begins to make terrible noises. He's just "coughing". That began after 6 months I had this computer. Now I found out, that I can temporarily fix this problem by "restarting" the audio stream of the application that plays music. For example reloading last.fm page (reloads the flash file). Another way to reset the audio playback is switching the speaker configuration shown below in the screenshot. According to many posts on the internet like http://www.tomshardware.co.uk/forum/52918-20-acer-aspire-6935g-speaker-problem ACER support isn't any help Exchanging hardware doesn't fix the problem Even the later models have this problem Turning off the volume of the subwoofer is not an option to me. I still have warranty (I bought an extension of one year). I already tried about 15 versions of the Realtek driver with no success. I am not sure but MAYBE the problem did not occur on the original windows vista that was shipped with this computer. However, I removed the original windows for good reasons (english). What do you suggest me? Did anyone fix this problem? Maybe by writing a script which resets the audio streams every 5 minutes? Shall I take the effort to deal with the acer support until they give me another model? (I won't have a computer than for a longer time, will spend money on telephone hotlines (1,30 EUR / min)......) Here are additional infos, if they are any help: Windows 7 64 Bit (Original was Windows Vista Home Premium 32 Bit) All specs Audio driver version:

  Read the article

• Remote Socket Read In Multi-Threaded Application Returns Zero Bytes or EINTR (104)

  - by user39891

  Hi. Am a c-coder for a while now - neither a newbie nor an expert. Now, I have a certain daemoned application in C on a PPC Linux. I use PHP's socket_connect as a client to connect to this service locally. The server uses epoll for multiplexing connections via a Unix socket. A user submitted string is parsed for certain characters/words using strstr() and if found, spawns 4 joinable threads to different websites simultaneously. I use socket, connect, write and read, to interact with the said webservers via TCP on their port 80 in each thread. All connections and writes seems successful. Reads to the webserver sockets fail however, with either (A) all 3 threads seem to hang, and only one thread returns -1 and errno is set to 104. The responding thread takes like 10 minutes - an eternity long:-(. *I read somewhere that the 104 (is EINTR?), which in the network context suggests that ...'the connection was reset by peer'; or (B) 0 bytes from 3 threads, and only 1 of the 4 threads actually returns some data. Isn't the socket read/write thread-safe? I use thread-safe (and reentrant) libc functions such as strtok_r, gethostbyname_r, etc. *I doubt that the said webhosts are actually resetting the connection, because when I run a single-threaded standalone (everything else equal) all things works perfectly right, but of course in series not parallel. There's a second problem too (oops), I can't write back to the client who connect to my epoll-ed Unix socket. My daemon application will hang and hog CPU 100% for ever. Yet nothing is written to the clients end. Am sure the client (a very typical PHP socket application) hasn't closed the connection whenever this is happening - no error(s) detected either. Any ideas? I cannot figure-out whatever is wrong even with Valgrind, GDB or much logging. Kindly help where you can.

  Read the article

• Stop the constant random reboots of my GIGABYTE GA-B75M-D3V

  - by Frederic

  I've got some issues with a new system. It's rebooting constantly. The system consists of a: brand new: Gigabyte GA-B75M-D3V with F9 BIOS (latest) Intel Core i5-3470 Ivy Bridge 2x 8GB G.SKILL Ripjaws 1600MHz memory (mem-tested x-86) coming from a stable system: Creative Soundcard X-FI Titanium Asus Radeon HD4850 OCZ Vertex 3 120G SSD Sata 3 Hard disk 1TB Sata 2 ASUS Blu-ray Drive PSU 400w Connected peripherals : Toshiba tv (displayport on dvi of MB or HD4850) Wired mouse, wireless keyboard (logitech) Bluetooth usb key Azio main problem : it's not possible to read the errors from the MB. nothing on the manual neither on internet. At the beginning, I received a MB with graphic problems and the problem of rebooting. I RMA'd it. The new one doesn't have any graphic problems. but it's still constantly rebooting. I removed everything except the HD, the sound-card, the blu-ray drive and the wireless keyboard. It's still unexpectdly rebooting. I'm running a test with just the motherboard and the HD. I will update this text after the test. I've got some questions : Somebody have an idea of a test? The PSU could cause that problem? I used it a lot of years with the stable system. Update 1: BTW, if anyone has the same problem, the manual won't say it but you'll need to reset the bios between two tests (the screwdriver on the two pins) if you suspect a problem of compatibility .

  Read the article

• No Homegroup Computers, Network Troubleshooter Fails

  - by Mokubai

  I have a problem with my Windows 7 Homegroup, between two Windows 7 Home Premium machines. On one machine I get this: The other machine in the Homegroup is perfectly happy and is able to see and browse this faulty machine as if there is nothing wrong. The Network and Sharing Center shows that I am joined to a Homegroup on my "Home" network and nothing is out of the ordinary. I have tried leaving the Homegroup and rejoining/recreating it several times and that does nothing at all. Normal browsing to machine names and looking through folders seems to work, but it's a much more clunky way to get stuff compared to the convenience of the Homegroup facilities. Starting the troubleshooter detects some problems with a "Peer Networking" (PNRpr or something like that) service not starting but fails to fix anything. Sure enough when I go to view the services via Control Panel - Administrative Tools - Services I see that both the "Peer Name Resolution Protocol" and "Peer Networking Grouping" services are stopped. Attempting to start the "Peer Networking Grouping" gives an error that a dependency service will not start, the only service it is dependant on is the "Peer Name Resolution Protocol" so I try to start that and I get an error saying that the "service could not start due to error 0x80630801" This has happened before and I have fixed it then by using System Restore and restoring the machine to a week before when I knew it had all worked. This time though I cannot remember when I last used the Homegroup from this machine and I've installed quite a bit so I don't want to go fumbling through restore points trying to find one that works... Can anyone tell me if there is a way to reset things so that this machine is able to use the Homegroup again?

  Read the article

• How to figure out what VirtualBox did?

  - by AndrejaKo

  I'm trying to boot a custom made-in-ASM OS on my recent laptop. The OS is intended to be installed on a floppy and during make creates a bootable floppy. Since I don't have a floppy drive, I installed it on a virtual floppy. After that I used WinToFlash's create bootable MS-DOS USB drive option to transfer the floppy image to an USB flash drive. Then I tried to boot my computer from it but got only a repeating broken string on screen. After all that I made a virtual hard disk image form the flash drive using this tutorial and tried to boot a virtual machine from it. First time I got same problem as on real computer. I then used the reset option and next time and every time after that OS booted correctly. My question is: How do I figure out what exactly happened to the virtual machine between first and second boot? UPDATE I just created a new VM with default settings for windows XP and it has the same problem that I have on a real computer. I was unable to reproduce the procedure which made the first VM work correctly.

  Read the article

• Extremely high mysqld CPU usage with no active queries

  - by RadarNyan

  I have a VPS running Ubuntu 12.04 LTS with LEMP stack, followed the guide from Linode Library (since I'm using a Linode) to setup, and everything worked fine until now. I don't know what's wrong, but my CPU usage just goes up since a week ago. Today things getting really bad - I got 74% CPU usage so I went check and found that mysqld taking too much CPU usage (somewhere around 30% ~ 80%) So I did some Google Search, tried disable InnoDB, restart mysql, reset ntp / system clock (Isn't this bug supposed to happen more than a year ago?!) and reboot my VPS, nothing helped. Even with mysql processlist empty, I still get mysqld CPU usage very high. I don't know what I missed and have totally no idea, any advice would be appreciated. Thanks in advance. Update: I got these from running "strace mysqld" write(2, "InnoDB: Unable to lock ./ibdata1"..., 44) = 44 write(2, "InnoDB: Check that you do not al"..., 115) = 115 select(0, NULL, NULL, NULL, {1, 0}^[[A^[[A) = 0 (Timeout) fcntl64(3, F_SETLK64, {type=F_WRLCK, whence=SEEK_SET, start=0, len=0}, 0xbfa496f8) = -1 EAGAIN (Resource temporarily unavailable) hum... I did tried to disable InnoDB and it didn't fix this problem. Any idea? Update2: # ps -e | grep mysqld 13099 ? 00:00:20 mysqld then use "strace -p 13099", the following lines appears repeatedly: fcntl64(12, F_GETFL) = 0x2 (flags O_RDWR) fcntl64(12, F_SETFL, O_RDWR|O_NONBLOCK) = 0 accept(12, {sa_family=AF_FILE, NULL}, [2]) = 14 fcntl64(12, F_SETFL, O_RDWR) = 0 getsockname(14, {sa_family=AF_FILE, path="/var/run/mysqld/mysqld.sock"}, [30]) = 0 fcntl64(14, F_SETFL, O_RDONLY) = 0 fcntl64(14, F_GETFL) = 0x2 (flags O_RDWR) setsockopt(14, SOL_SOCKET, SO_RCVTIMEO, "\36\0\0\0\0\0\0\0", 8) = 0 setsockopt(14, SOL_SOCKET, SO_SNDTIMEO, "<\0\0\0\0\0\0\0", 8) = 0 fcntl64(14, F_SETFL, O_RDWR|O_NONBLOCK) = 0 setsockopt(14, SOL_IP, IP_TOS, [8], 4) = -1 EOPNOTSUPP (Operation not supported) futex(0xb786a584, FUTEX_WAKE_OP_PRIVATE, 1, 1, 0xb786a580, {FUTEX_OP_SET, 0, FUTEX_OP_CMP_GT, 1}) = 1 futex(0xb7869998, FUTEX_WAKE_PRIVATE, 1) = 1 poll([{fd=10, events=POLLIN}, {fd=12, events=POLLIN}], 2, -1) = 1 ([{fd=12, revents=POLLIN}]) er... now I totally don't get it x_x help

  Read the article

• So who decided VGA cables should be symetrical ? [closed]

  - by mgb

  < rant So who decided that VGA cables should be the same gender connector at both ends? I just spent an hour trying to fix a server that would apparently boot but wouldn't display any post messages - I needed to change some bios settings. The monitor gives me a helpful error message - "unable to display this resolution". Wondering how it can't show simple VGA res, I reset the bios, when that doesn't work I remove the BIOS battery. The system is in a rack with a keyboard and monitor mounted 6ft away - with the cable running through the normal waist thick rats nest of wiring of wiring. The monitor worked with another system, so it and the VGA cable are good, I brought in another monitor and tried that - still nothing. Eventually I ripped the rack apart to discover that the other end of the VGA connector I was trying to plug into the server was actually plugged into another server box ! And the second monitor I was testing was plugged into the first monitor. An error message like - "I'm actualy plugged into another monitor stupid" - would be useful. So would having a connector with a male end and a female end. < end rant - thank you

  Read the article

• BSOD: PFN_LIST_CORRUPT and IRQ_NOT_LESS_OR_EQUAL

  - by David Lively

  I built a desktop about a year ago that has, until a few weeks ago, been running without a hitch using Windows 7 Ultimate. Recently, the PC started occasionally rebooting with a blue screen indicating a "PFN_LIST_CORRUPT" error. Also, I've seen at least once the error IRQ_NOT_LESS_OR_EQUAL. I seem to remember temporarily connecting an internal DVD burner about the same time this happened. I burned a DVD for another machine and promptly removed the drive. Yesterday, I reformatted the drive and installed Win7 Ultimate x64. During the first install, the PFN_LIST_CORRUPT bluescreen reared its ugly head again. A second install attempt completed with no errors. The fact that this error happened during a clean install leads me to believe that this is not a driver or OS issue. I also ran the memory diagnostic from the Win7 32-bit install DVD. It completed both passes with no errors. Periodically, the screen will flicker, as if explorer or the video are resetting. In the event log, I see a series of 8 or so errors indicating that some services unexpectedly stopped, and were apparently reset. These include an HID service and some others (I don't have a list in front of me). The PC is a Phenom X2 3 Ghz with a 500GB Seagate drive, 4GB of Corsair XMS2 cm2x2048-6400c5c. Anyone know what would suddenly cause a couple of sticks of RAM to go bad?

  Read the article

• MySQL partition "full"?

  - by gdea73

  I have a server that runs Debian 6.2, with Apache, PHP5, and MySQL. Well, I hadn't done anything with MySQL at all so far, just Apache and PHP; I must have installed it (mysql-server) at some point along the line, and I decided to login to the database for the first time a couple days ago as I was considering using the database for a future website project. I noticed that the "root" user had a password, and I didn't recall having set one. My usual root password was incorrect. So I attempted to reset the password. sudo service mysql stop (stopped successfully) sudo /usr/bin/mysqld_safe --skip-grant-tables --skip-networking & started successfully, from what I can tell. However, mysql itself returns "Can't connect to local MySQL server through socket '/var/run/mysqld/mysqld,sock' (2)", and additionally sudo service mysql start returns "/etc/init.d/mysql: ERROR: The partition with /var/lib/mysql is too full! ... failed!" df -h tells me that / is 26% used, a 20GB partition, and /home, roughly 900GB, has only 5% usage. On a potentially related note, I've been experiencing random hangs since I noticed this problem, my tty2 randomly froze several times while idle, and the entire system is suddenly unstable. gnome-terminal also does not open. (Gnome-terminal apparently works now, disregard that part, but the server is still being somewhat unstable, I randomly lost connection when I was SSHed into it from my laptop, twice now.)

  Read the article

• SATA Driver for Acer Aspire One D257

  - by Robert Niestroj

  i have a Acer Aspire One D257. In this netbook the hard disk is defect so i bought a new one. Now i want to reinstall Windows 7. Im using an external DVD Drive plugged into USB. The Windows 7 DVD is staring, Win7 setup is starting and when it comes to Hard Drive options it says that no drive was detected and i should try search for drivers. It shows me this window: Screenshot from web Now i cant find the right drivers for this netbook to continue with the installation. The laptop has the newest BIOS - 1.15, it is reset to factory default settings except that i enabled the Boot Menu prompt with F12. From the Acer Support Website i've downloaded the SATA AHCI Driver and the Chipset Driver. I unpacked both to a USB flashdrive in seperate folders. When i select the SATA AHCI Driver it does not find any drivers. When i uncheck the checkbox "Hide drivers that are not compatible with hardware on this computer" it shows one driver: Acer HWID (path_to\1.inf). When i continue with this driver i got an error message that says something like: No new devices found. Check if the driver files are on the installation disk. When i show him the Chipset Driver it sees a lot more driver. When i uncheck the checkbox "Hide drivers that are not compatible with hardware on this computer" it show some drivers: Intel N10 Family DMI Bridge Intel N10/ICH7 Family PCI Express Root Port Intel N10/ICH7 SMBUS Controller Intel N10/ICH7 Family USB Universal Host Controller Intel N10/ICH7 Family USB2 Enhanced Host Controller Intel N10/ICH7 Family Interface LPC Controller When i uncheck this checkbox i get a lot more drivers, and some SATA Drivers but the also do not work. I get the same error message as before. Can someone help me find a driver that should work or am i doing anything else wrong?

  Read the article

• Setting up port forwarding for web server

  - by reyjavikvi

  This could belong on Super User, but I thought this place was more appropiate. I want to run Apache in my computer and want to make it available to the outside world to test a couple things. Apparently, I have to go into my router's (a TP-LINK TD 8910G) settings and forward port 80 to my PC's IP. So far so good. Thing is, since the router uses a web based interface and it's kind of stupid, it told me that since I was using port 80 for this, I should access its settings through port 8080. Maybe it can't detect requests coming from the LAN, I don't know. Point is, now neither port can't access the configuration, and I can't access Internet. Specifically, trying to access anything (including 192.168.1.1, the router's settings) through port 80 turns up a blank page (maybe if I had the server running in my computer I'd get something, but I don't want to risk trying, I had to reset the router and restore the settings), and port 8080 gives a "Can't establish connection" error in Firefox (and similar ones in other browsers). Is there a way to configure the router to not redirect requests coming from inside the network? I'm a beginner with this stuff, so please try to explain in a simple way. If this is more appropiate in Super User, I'm sorry.

  Read the article

• mac gets stuck in a blue screen during boot

  - by user10826

  Hi, a macbook pro 2008 unibody, after restart gets stuck in a blue screen. I used the Leopard disk and I verified and repaired permissions, which seem to be a problem, because the assistant found some wrong files. After restart I got the same problem. After googling I reset PRAM and the other (I do not remember the name now). Same problem. I check that I can boot in safe mode, although it is a lot slower. So before anything I try to make a time machine backup, hoping that I can be done from safe mode. First question: If it works, is it possible to do a clean leopard install (I do not like Snow) and migrate all user accounts from the backup, although it was done in safe mode? Second question: I read about the feature "archive and install" from the leopard disc. Is it reliable? Because I am afraid of losing all data ... Third question: I think this boot stuck has to do with the load of some program or service. It would explain why the computer does boot on safe mode and not in the normal one. I would then like to check what the computer loads during boot, but in more detail that with the information provided from /system preferecens/account/start, because there I removed everything. Where can I find more advanced information? And, if I remove programs from the safe mode, will it be effective druing the normal boot? Thanks

  Read the article

• Dovecot authentification not working

  - by user1488723

  I run a Ubuntu 10.04 VPS with Postfix and Dovecot installed. For a while I had problems with the mailserver itself (Postfix) but now it runs ok. I can telnet into it from localhost (telnet localhost 25 while logged in) and Im blocked if I try to do it from the outside (telnet mail.example.org 25). This is as it should be according to my main.cf However when I try to log in using Dovecot (openssl s_client -connect mail.example.com:993) I'm allowed in but denied when trying to identify myself as a user: Excerpt from Dovecot log in: Key-Arg : None Start Time: 1341074622 Timeout : 300 (sec) Verify return code: 18 (self signed certificate) OK [CAPABILITY IMAP4rev1 LITERAL+ SASL-IR LOGIN-REFERRALS ID ENABLE AUTH=PLAIN AUTH=LOGIN] Dovecot ready. When I continue and try to log in to a specific user with the command: A001 login user password I get: A001 NO [AUTHENTICATIONFAILED] Authentication failed. I've reset the password to ensure it is correct and I know the user (user) exists on the system. When I do /etc/init.d/dovecot reload I get: /etc/init.d/dovecot: 29: maildir:~/Maildir: not found * Reloading IMAP/POP3 mail server dovecot [ OK ] Could it be that the mailboxes isn't found? Postfix main.cf: home_mailbox = Maildir/ mailbox_command = recipient_delimiter = + inet_interfaces = all smtpd_use_tls = yes smtpd_tls_auth_only = no smtpd_tls_loglevel = 1 smtpd_tls_cert_file = /etc/postfix/ssl/smtpd.crt smtpd_tls_key_file = /etc/postfix/ssl/smtpd.key smtpd_tls_CAfile = /etc/postfix/ssl/cacert.pem smtpd_sasl_auth_enable = yes smtpd_client_restrictions = permit_sasl_authenticated, permit_mynetworks, reject_unauth_destination smtpd_sender_restrictions = permit_sasl_authenticated, permit_mynetworks smtpd_recipient_restrictions = permit_mynetworks, permit_sasl_authenticated, reject_unauth_destination broken_sasl_auth_clients = yes smtpd_sasl_type = dovecot smtpd_sasl_path = private/auth smtpd_sasl_security_options = noanonymous smtpd_sasl_local_domain = $mydomain Dovecot.conf: protocols = imap imaps disable_plaintext_auth = no log_timestamp = "%b %d %H:%M:%S " ssl = yes ssl_cert_file = /etc/postfix/ssl/smtpd.crt ssl_key_file = /etc/postfix/ssl/smtpd.key mail_location = maildir:~/Maildir auth_verbose = yes mail_access_groups = mail auth_username_chars = abcdefghijklmnopqrstuvwxyz0123456789 protocol imap { imap_client_workarounds = delay-newmail tb-extra-mailbox-sep } auth default { mechanisms = plain login passdb pam { } userdb passwd { } socket listen { client { path = /var/spool/postfix/private/auth user = postfix group = postfix mode = 0660 } } }

  Read the article

• Can't upgrade NVIDIA GeForce 310M display driver on Acer Aspire 5745PG

  - by Emerson

  I've been for days already trying to update my video driver. I have an Acer Aspire 5745PG with a "NVIDIA GeForce 310M" board, and I was trying to run Sony Vegas video editor with Boris Continunn plugins. It happened that some of the plugins, like BCC Text Extrude wouldn't work, showing the message "Insufficient depth resolution to run Blue". I then read somewhere that updating the display driver would do the trick. That was when my nightmares started, I lost already good 3 nights trying to sort this out, without success :( The display driver that was before (and that I current have after restoring) was the version 8.16.11.8997. First thing I tried was downloading the 8.17.12.6619 driver directly from Acer, which was shown as the latest version from Acer website: http://support.acer.com/product/default.aspx?modelId=2466 Running it would say "Diver Package Failure - Setup failed to read the required Display Driver to be used with this package" I then tried directly the NVIDIA own driver, which the latest was version 296.10: http://us.download.nvidia.com/Windows/296.10/296.10-notebook-win7-winvista-64bit-international-whql.exe That gave me similar error message :/ So after some researching I found out that some people had the same issue and they had to change the configuration file to allow the installer to recognize this NVIDIA board: http://forums.nvidia.com/index.php?showtopic=222904 That topic said to look for the "Device Instance Id" property of the "NVIDIA GeForce 310M" display , which I couldn't find, instead I found the "Hardware Id", which seemed to be the right one. I followed the instructions and changed the inf file first for the Acer installation, and after for the NVIDIA own driver. It actually managed to go ahead with the installation in both instances, but the only thing I got was a black screen, while the computer still apeared to be running fine. I had to hard reset, and then it would come back with generic vga driver. I could only get my display back using the recovery function. I imagine thousands of this notebook was sold, and it can't have its driver updated?? Could someone help me with this?? Thanks Echo

  Read the article

• Replacing compiz/metacity with openbox reduces workspaces to 1

  - by Brian

  I like to use the GNOME desktop, but I prefer to replace its window manager with openbox, with 4 workspaces. However, when I run openbox --replace, the number of workspaces available drops to 1. If I go into obconf, workspaces is still configured to be 4 (~/.config/openbox/rc.xml shows the same). I can get the workspaces to reappear by changing the value in obconf to anything else, and then back to 4. I have just been dealing with this problem since Ubuntu 9.04 (now up to 10.10) since I don't reboot very often. But it's really annoying to have to reset my workspaces whenever I do have to reboot. Changing the value in rc.xml and running openbox --reconfigure does not seem to have any effect. So what is obconf doing that I'm not (sends a dbus message perhaps [EDIT: watching with dbus-monitor I see no messages when changing the workspaces value in obconf])? I was hoping there would be a cleaner way to change the window manager than just running openbox --replace at login. So my questions are: Is there a better way to specify an alternate window manager (i.e. a way that doesn't cause the workspaces to break)? If not, how can I automatically set the number of workspaces back to 4? Update: I finally got around to trying what I commented on MrShunz's answer (adding WINDOW_MANAGER=/usr/bin/openbox to ~/.gnomerc). But the effect is the same as openbox --replace.

  Read the article

< Previous Page | 205 206 207 208 209 210 211 212 213 214 215 216  | Next Page >