Search Results

Search found 22300 results on 892 pages for 'half bit'.

Page 208/892 | < Previous Page | 204 205 206 207 208 209 210 211 212 213 214 215  | Next Page >

• Intel NIC X540-T1 non-functional in Ubuntu Server 12.04

  - by Jeff Carr

  I have installed three Intel X540-T1's in servers running Ubuntu Server 12.04, but all are non-functional, no link lights, no packets sent or received, and no connection on ip4 or ip6 whether set up as dhcp or static. Also, dmesg doesn't detect cable connection or disconnection. I updated the default ixgbe driver to Intel's latest version (3.11.33) with no change. The ethernet controller is being reported as X540-AT2 (which might be a problem that I can't figure out how to fix), but the subsystem is X540-T1 so I believe that might be intended. Does anyone have any experience with this that could assist? ifconfig eth2 eth2 Link encap:Ethernet HWaddr a0:36:9f:14:5f:ea inet addr:192.168.101.1 Bcast:192.168.101.255 Mask:255.255.255.0 UP BROADCAST MULTICAST MTU:1500 Metric:1<br> RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) ethtool -i eth2 driver: ixgbe version: 3.11.33 firmware-version: 0x8000037c bus-info: 0000:08:00.0 supports-statistics: yes supports-test: yes supports-eeprom-access: yes supports-register-dump: yes lspci -vvnns 08:00.0 08:00.0 Ethernet controller [0200]: Intel Corporation Ethernet Controller 10 Gigabit X540-AT2 [8086:1528] (rev 01) Subsystem: Intel Corporation Ethernet Converged Network Adapter X540-T1 [8086:0002] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 32 bytes Interrupt: pin A routed to IRQ 16 Region 0: Memory at e8000000 (64-bit, prefetchable) [size=2M] Region 4: Memory at e8200000 (64-bit, prefetchable) [size=16K] [virtual] Expansion ROM at e8280000 [disabled] [size=512K] Capabilities: <access denied> Kernel driver in use: ixgbe Kernel modules: ixgbe

  Read the article

• Power supply surges detected during previous power on

  - by Blastcore

  Message is this: "Power supply surges detected during previous power on" "ASUS Auto-Surge was triggered to protect system from unstable power supply" When i went to sleep yesterday and woke up, when i moved the mouse to go back from screen saver, it didn't do anything. So i left it, i came back from class and got this issue. (I didn't restart before going to class... So the screen was left like it was) Today there was a power cut in half of my house. (Computer is on the side that it didn't cut...) Voltages are fine, like always. How do i remove message? It's just maybe sensor glitch? Even disabling the Anti-Surge my PC "shuts down" (Only monitor, but maybe components do too.)

  Read the article

• filesystem compatible with freenas and windows

  - by Daniel

  Hi all, I'm planning on using FreeNAS (was considering openfiler but freenas seems simpler) for my home NAS box running off ESXI. I have managed to get local sata drives to mount in ESXI (http://serverfault.com/questions/216902/esxi-add-datastore-without-partitioning). I've had one of the drives fail on my before and I was able to retrieve most of the data off it using windows tools (I'm not much of a linux guy I know enough to be dangerous!). If I go the freenas route in the event that something goes bad what would be the best file system to use so that I could pop the drive out of the freenas box (vm) and put it in another pc running windows so I could try and run various recovery tools to get the data back. All in all its not a major problem if I lose the data just would be a bit annoying, so I'm not looking for suggestions around backing up etc. I was considering using NTFS that the drives are already formatted as but it appears that while freenas does support NTFS that its a bit buggy and not 100% reliable, anyone know if this is still true? Read that on a forum somewhere.

  Read the article

• Is it possible to use the MMM tool without virtual IP capability?

  - by Artem

  We are on a host (Serverbeach) that does not support Virtual/floating IPs until you reserve at least a half-rack, which is just a little more than we are willing to spend per month right now. We do have 2 machines in one of their datacenters, and I am using these 2 machines right now in the Master-Master in Active-Passive Mode just like done by MMM -- http://mysql-mmm.org/. I have just set them up and I managing them manually, with manual switch on the Web frontend to tell it to connect to the correct (active) master. Is there any way to use MMM without virtual IPs? Any other comments on this setup?

  Read the article

• Internal+external interfaces with multiple default gateways on win2003

  - by fileitup

  Im trying to set up several web servers for a load balanced cluster and need to have each server connected to the internal network (for load balancing) as well as to an external network (internet - for administration). I have two NICs but since I cant set two default gateways I have the external gateway as default and the internal as a route rule. This setup only works half way - the internal network is fine but I cant log in from outside or see the web from the box. If I switch the gateways remote login/web will work, but the internal wont. Im sure someone encountered this before but wasnt able to find anything online. Any help will be appreciated.

  Read the article

• File in use when it's really not

  - by C-dizzle

  I am running Windows 7 Professional 32 bit on a Server 2008 network. I am getting a weird issue with an excel document where I open it up one morning, update it, save and close, the next morning I come in, open it up and it says "This file is in use and locked by csmith" which "csmith" is me! So I click on the cancel button, open it up again and it comes up fine. I can edit, save and close with no problem. But then have the same issue the next morning. Another weird thing is that we have a calendar shared in "Public Folders" under Outlook that seems to be having the same issue, which happens to be a calendar made in Excel. Exchange 2010 is installed on the server and the clients are using Exchange 2007. In the instance with the calendar, it will show conflicting edits have been made and you must keep one item or all items. And it shows an edit date of 4/24/2012 and 6/1/2012. But, there were NO edits done on 6/1, just tried opening it. This problem does not occur under my profile, but 2 others. These machines are ALSO running Windows 7 Professional 32 bit. We have a mix of Windows 7 and Windows XP machines on our network if that is any help. These issues did not start happening until we migrated from a server running Server 2003 and Exchange 2000, which the new server is running Server 2008 and Exchange 2010 as stated above. Is there something on the server side that is configured wrong?

  Read the article

• Error while installing boost_1_54

  - by Farhat

  On trying to install boost I get this error during configuration checks. Googling did not give any pointers. [root@heracles boost_1_54_0]# ./b2 install Performing configuration checks - 32-bit : no (cached) - 64-bit : yes (cached) - arm : no (cached) - mips1 : no (cached) - power : no (cached) - sparc : no (cached) - x86 : yes (cached) error: No best alternative for libs/coroutine/build/allocator_sources next alternative: required properties: <link>static <target-os>windows <threading>multi not matched next alternative: required properties: <link>static <segmented-stacks>on <threading>multi not matched next alternative: required properties: <link>static <threading>multi not matched - has_icu builds : no (cached) warning: Graph library does not contain MPI-based parallel components. note: to enable them, add "using mpi ;" to your user-config.jam - zlib : yes (cached) - iconv (libc) : yes (cached) - icu : no (cached) - icu (lib64) : no (cached) - compiler-supports-ssse3 : yes (cached) - compiler-supports-avx2 : no (cached) - gcc visibility : yes (cached) - long double support : yes (cached) warning: skipping optional Message Passing Interface (MPI) library. note: to enable MPI support, add "using mpi ;" to user-config.jam. note: to suppress this message, pass "--without-mpi" to bjam. note: otherwise, you can safely ignore this message. error: No best alternative for libs/coroutine/build/allocator_sources next alternative: required properties: <link>static <target-os>windows <threading>multi not matched next alternative: required properties: <link>static <segmented-stacks>on <threading>multi not matched next alternative: required properties: <link>static <threading>multi not matched - zlib : yes (cached) How can the alternative for allocator sources be located? Thanks.

  Read the article

• Is there a version of the Arial or Tahoma font with monospaced digits and spaces?

  - by rossmcm

  The digits in the Arial font supplied with Windows are monospaced, in that they each take up the same horizontal space, but they seem to have neglected to provide a "monospaced" version of the space character. This means that you can't format a column of digits right-justified in (say) 12 spaces and have the right-hand edge be aligned. For example: 1 12 123 1234 12345 1234567 12345678 123456789 1234567890 works because the font used for code examples has spaces the same width as digits. This however doesn't work if the same text is displayed in Arial (I can't demonstrate because I can't figure out how to defeat SU's reformatting at the moment!). It just so happens that with Tahoma 8 point you can cheat because a space is exactly half the number of pixels as a digit, but that is messy and very specific.

  Read the article

• W2k8 RC1: Windows Media Servers (WMS) as proxy

  - by da_didi

  (fullquote from stackoverflow.com/questions/2690788/w2k8-rc1-windows-media-servers-wms-as-proxy/2690791#2690791) I will have one streaming-server (W2k8, unknown streaming protocol [rtsp, mss, http]) and half dozen streaming-servers as proxies to save bandwidth. I have read the documentation and installed the modules, but I am unsure how I have to configure the proxy's according to http://technet.microsoft.com/de-de/library/ee126142(en-us,WS.10).aspx - as a proxy or reverse proxy and how I minimize the bandwidth needs between origin server and proxy's. What is the best way to realize my setup? Any short how-tos? How can I announce all players to use the proxy? Route all rtsp/mms/http-requests through my proxy? Announce the proxy with DHCP-releases? Thanks!

  Read the article

• Icinga notifications are being marked as spam when sent to my mailbox

  - by user784637

  I'm using gmail and my domain is foo.com About half the notifications from my icinga server, [email protected] go to my spam folder for [email protected] Received-SPF: fail (google.com: domain of [email protected] does not designate <ip6> as permitted sender) client-ip=<ip6>; Authentication-Results: mx.google.com; spf=hardfail (google.com: domain of [email protected] does not designate <ip6> as permitted sender) [email protected] Is my current SPF record set up to allow my icinga server with the ip <ip4> and <ip6> to send email from the domain foo.com? ;; ANSWER SECTION: foo.com. 300 IN TXT "v=spf1 ip4:<ip4> ip6:<ip6> -all"

  Read the article

• SLA Violations - Compensation expectations and vague contracts

  - by llllxllll

  Tagging this as cautionary tale. I took over for an admin a year and a half ago, and reviewed the 3 year contract with our ISP. There were no specific SLA promises in the contract that I found, and have been meaning to review the contract with our rep. Of course, we had an outage this past week that resulted in almost four days of downtime !!!!! This involves eff-ups of epic proportions on our ISP's part and a telco they colocate with. Details can be provided. I am the network / systems / purchasing / and helpdesk at my company...and am willing to fight with the ISP. I also have more management that can get involved, including the name on the contract. First, if there are not concrete guarantees about compensation and downtime, we are screwed right? Two, if we want out of our contract, does anyone have experience going the legal route, and if so, who knows a lawyer? =)

  Read the article

• Is there the equivalent of cloud computing for modems?

  - by morpheous

  I asked this question on SF, and someone recommended that I ask it here - (I don't think I have enough points to move a question from SF to SO - and in any case, I don't know how to do it - so here is the question again): I am interested in the concept of PAAS (platform as a service). However, all talk about SAAS/PAAS seems to focus on only the computer itself - not its peripherals. Is it possible to 'outsource' modems as a resource - so that an app running remotely can pump data to a modem in the cloud? As a bit of background to the question, a group of us are thinking of starting a company that offers similar services to companies like twilio etc - but I want to 'outsource' both the computing hardware (thats PAAS - the easy bit) and the modems (thats what I cant seem to find any info on). Does anyone know if modems can be bundled as part of a PAAS service? - alternatively, is there a way that an application running on one computer can communicate (i.e. pump data) to a remote modem residing on another machine?. I assume I can come up with some protocol over UDP or TCP - but there is no point reinventing the wheel - if such a protocol like that already exists (or if it some open source software allows one to do this). Any suggestions on how to solve this problem?

  Read the article

• Using Varnish (only) for DDoS mitigation

  - by Martin Kanters

  My VPS is suffering from a (D)DoS doing a SYN flood with spoofed IPs. I'm right now searching from ways how to be able to defend (at least a bit) against it. It's running a DirectAdmin apache2 webserver. Mainly used for serving PHP and MySQL. We are using CloudFlare, which are saying that they are able to mitigate (D)DoS at some level, now the attacker knows our real IP address, so CloudFlare isn't helping a bit. I've done some searching on the net and found out about enabling SYN cookies, to defend against it. I've checked my settings and it seems it was enabled all along. I've also read about that Varnish is able to defend against SYN flooding and Slowloris attacks, now I'm pretty interested in using that. The thing is that CloudFlare is already caching a lot from us, and I don't wish to spend too much resources on Varnish. Is it possible and smart to set up Varnish only for the better handling of requests? Are there perhaps better ways which I've missed? Thanks in advance, Martin

  Read the article

• Server setup scripts, patches and migrations

  - by Ben Swinburne

  I have written some scripts which I use to configure various servers in a uniform way. Each time I deploy a server I run the relevant scripts so that I know they're all configured the same. I then have some patch scripts, which are changes to the originals which I can then run to ensure that modifications to the original set up can be run on each server. E.g. disable.sh - Disable SELinux etc to ensure other scripts all run correctly general.sh - Jailkit, AV, Repos, RKHunter, security tweaks, uninstall unused bits etc web.sh - Installs and configures Apache2 001_update_nr_licence_key.sh - Update a licence key for a piece of software which has changed since its install in general.sh I can run the first 3 without a problem, but when it comes to running patches I am a bit stuck. Is there a sensible way of doing these with some software? My current thought is write to a log file the role of the server be it web or db for example and then note the name of the patch which has run. It could then iterate through a folder to find all patches for that role which it has not yet run and execute them. This seems a bit long winded however. Could someone advise me as to the best way I can keep my servers uniform?

  Read the article

• Laptop connected to external monitor results in desktop overflow

  - by Andrew Fox

  I have a laptop (MSi FX600) connected to an external monitor (Toshiba 19AV500U) with the screen resolution set to the monitors recommended setting of 1440x900. The problem is the desktop is overflowing the display, meaning all edges of the desktop are cut off, so I cannot see the close, minimize buttons on the top and I only see half of the taskbar at the bottom. I have tried many different resolutions but none of them solve the problem. I have had this same problem when connecting to other external monitors in the past, but not all of them, it seems to be fairly random. I have tried to find a way to manually adjust the resolution but I cannot see a way to do this in my settings. All windows updates are up to date, I am connecting through an HDMI cable and I have it set to display only on the external monitor and not extended desktop.

  Read the article

• How do I improve my screen resolution in Windows Remote Desktop?

  - by Jeff

  I'm RDP'ing into a Win2K3 machine from a WinXP machine, and I cannot stand the low screen resolution I get on the Win2K3 box. Text is too large and the graphics/colors aren't very smooth. How do I improve this? If I right-click on the desktop of the remote machine and go to Properties - Settings, I see that the screen resolution is set to 1280x1024 (should be okay, I would think), and the color quality is Medium (16 bit) (not optimal) and I don't have the option to change either setting (because they're set in the .rdp file for the session, right?). If I move over to the Appearance tab, I see that font size is set to Normal, with no option to make it smaller. The thing is, these settings are close to what I have on the XP machine I'm RDP'ing in from. The only difference (in those settings) is the color quality, which is 32 bit. Any ideas on how I can improve the situation? Other tidbits: The graphics card on the Win2K3 machine is ATI ES1000. I think I have the latest drivers for it. I'm running VMware Workstation on the Win2K3 machine, and if I create a Win2K3 VM and RDP into it from the XP machine, the resolution is just fine.

  Read the article

• Replicating/Synchronizng multiple tables across diffrent Databases on the same instance

  - by Idan

  I have few tables that needed to be replicated/synchronized across several databases in our SQL Server 2008 cluster. I know it's possible to replicate between multiple instances, but I'm looking for replication or synchronization in the same instance between specific tables of databases. The replicaiton/synchronization should happen every half-hour or so, but I don't mind it happening constantly. I can't use DROP the target table and INSERT (copy) the source table since there are many constraints. Reason for this is to not manage in the application layer and write to 2 different databases at the same time. Example: DB1 has T1, T2 and T3 - these are constantly being updated by the application, APP1 running on DB1. DB2 needs to have an updated copy of T1 at all times, also, there is a different application, APP2 runs only on DB2. Both DB1 and DB2 are located on the same instance, INST1. Would it be possible to replicate T1, T2 and T3 from DB1 to DB2 ? Thanks, Idan.

  Read the article

• Any good software to help me memorize passwords?

  - by Septagram

  I'm using KeePass(X) and other tools to keep most of my passwords. However, it turns out, there is still about half a dozen passwords I'm using on regular basis that I would prefer to just remember. So, do you people know of any good programs, preferably open-source, to train yourself using a particular password and thus to memorize it? I know I can remember a 96-bit entropy password rather well if I practice entering it 3 days, 5 minutes for each day, I just want a good software to simplify the process and exclude the possibility of shouldering or otherwise leaking the password.

  Read the article

• CPU load, USB connection vs. NIC

  - by T.J. Crowder

  In general, and understanding the answer may vary by manufacturer and model (and driver, and...), in consumer-grade workstations with integrated NICs, does the NIC rely on the CPU for a lot of help (as is typically the case with a USB controller, for instance), or is it fairly intelligent and capable on its own (like, say, the typical Firewire controller)? Or is the question too general to answer? (If it matters, you can assume Linux.) Background: I'm looking at connecting a device (digital television capture) that will be delivering ~20-50 Mbit/sec of data to a somewhat under-powered workstation. I can get a USB 2 High-speed device, or a network-attached device, and am interested in avoiding impacting the CPU where possible. Obviously, if it's a 100Mbit NIC, that's roughly half its theoretical inbound bandwidth, whereas it's only roughly a tenth of the 480 Mbit/second the USB 2 "High Speed" interface. But if the latter requires a lot of CPU support and the former doesn't...

  Read the article

• Oracle 10g for Windows does not start up on system boot

  - by Mike Dimmick

  We have an Oracle 10g Enterprise Edition installation (10.2.0.1.0) on a Windows Server 2003 virtual machine. It was initially created with Virtual Server 2005 R2 SP1 but has now been migrated to Windows Server 2008 Hyper-V. The services start on system boot, but the instance does not start up. This problem was actually occurring on Virtual Server after a migration from one server to another, but I managed to fix it then with: oradim -edit -sid ORCL -startmode auto However, this now has no effect. oradim.log (in %OracleHome%\database\oradim.log) says: Thu Jun 10 14:14:48 2010 C:\oracle\product\10.2.0\db_3\bin\oradim.exe -startup -sid orcl -usrpwd * -log oradim.log -nocheck 0 Thu Jun 10 14:14:48 2010 ORA-12560: TNS:protocol adapter error sqlnet.log in the same folder has: Fatal NI connect error 12560, connecting to: (DESCRIPTION=(ADDRESS=(PROTOCOL=BEQ)(PROGRAM=oracle)(ARGV0=oracleorcl)(ARGS='(DESCRIPTION=(LOCAL=YES)(ADDRESS=(PROTOCOL=beq)))'))(CONNECT_DATA=(SID=orcl)(CID=(PROGRAM=C:\oracle\product\10.2.0\db_3\bin\oradim.exe)(HOST=ORACLE-VM)(USER=SYSTEM)))) VERSION INFORMATION: TNS for 32-bit Windows: Version 10.2.0.1.0 - Production Oracle Bequeath NT Protocol Adapter for 32-bit Windows: Version 10.2.0.1.0 - Production Time: 10-JUN-2010 14:14:48 Tracing not turned on. Tns error struct: ns main err code: 12560 TNS-12560: TNS:protocol adapter error ns secondary err code: 0 nt main err code: 530 TNS-00530: Protocol adapter error nt secondary err code: 2 nt OS err code: 0 The ORA_ORCL_AUTOSTART registry value is set to TRUE, so it should be auto-starting - and you can see that it's trying to. The problem also occurs when stopping and restarting the OracleServiceORCL service. I've enabled SQL*Net tracing which shows: [10-JUN-2010 15:09:33.919] snlpcss: entry [10-JUN-2010 15:09:34.419] snlpcss: Unable to spawn Oracle oracle (DESCRIPTION=(LOCAL=YES)(ADDRESS=(PROTOCOL=beq))) orcl, error 2. [10-JUN-2010 15:09:34.419] snlpcall: exit On a hunch that error 2 is Windows error 2 (file not found) I tried restarting the service with Process Monitor watching oradim.exe, but this appears to delay things just enough that it always works. Right now I have a horrible hack where I've created a Scheduled Task to run oradim -startup -sid ORCL when the Administrator account logs on, and set the VM to auto-logon. I'd still like to work out why it's not working.

  Read the article

• Router block some sites

  - by Mahesha999

  Hi I was using ADSL Modem/Router earlier. The device is quite old Pronet PN-ADSL 101 E/U model (pics: http://bit.ly/P2YaWy, http://bit.ly/OA700l) Since it had only one RJ45 out, I bought new Wireless Router TPLink TL-WR941ND. It has 4 RJ45 out and 3 wireless antennas. I configured my old router in bridge. Now, if I have to connect my pc to Internet through the old router, I have to enter username and password. Then I connected the RJ45 output of old router to the WAN in of new router. and ran the CD of new router. It configured the new router in PPPoE by saving the username and password in router to dial automatically. So now I have to just plug in the wires in my new routers any RJ45 out. I am able to access the Internet when I connect through new router (both wired and wirelessly), but some sites are getting blocked. Most notably yahoo.com (though ymail.com is working), Microsoft.com. msn.com. These sites work perfectly fine when I connect my pc directly to my old router and enter username and password manually. (However others like google.com. facebook.com works fine when connect through new router) So here these some sites need some parameter set but I am unable to find them out. Can anyone help me. My friend said he also faced same problem. Surprisingly he advised me to see if the same websites will work through Opera turbo mode and boom they worked. So what could be the problem?

  Read the article

• Asus MyCinema U3100mini Choppy

  - by dsimcha

  I'm running an Asus MyCinema U3100mini ATSC on Windows 7 64-bit. When I play live TV in Windows Media Center, it's very choppy and uses 500+ MB of RAM, I'm guessing due to the hard drive buffering functionality. Is there any way to disable the live TV pause buffer completely? If not, can anyone recommend alternative software that: Works with the MyCinema. Is lightweight and not horribly bloated with features I'll never use like Windows Media Center is. Edits: This is a dual boot system. I've discovered that the tuner actually works fine on XP. It also works fine on my other computer, which has slower hardware and also runs Windows 7 64-bit. The problem actually seems to be with playback at large screen sizes, not with hard drive buffering. Everything works fine below a certain window size and fails for large windows or full screens. Also, the same thing seems to happen whether playing live or recorded TV. As far as the obvious stuff goes, I have the latest video drivers from ATI for my Radeon x1050.

  Read the article

• Can you transfer a Windows 7 XP-mode VHD to a new PC without the need for reactivation?

  - by Henk

  Hi. At the moment I am running Vista 32 bit and use VPC 2007 a lot. I have several W2000 VMs set up with complex software configurations. For me, one of the advantages of working with VPCs is that a VM can easily be copied to another PC (like a notebook). Also, when I move to a new PC, I can immediately work with my existing VMs without the need to reinstall all applications. I am thinking about buying a new pc with Windows 7 64 bit pro, and using the xp-mode VM that comes with Windows 7. The advantages would be support for more memory (so being able to run more VM's simultaneously) and having a licenced XP VM. I would like to know if you can transfer a VHD that is based on the xp-mode VHD to another machine without Activation issues. The other machine will of course, also be running W7. I would guess that this would not be a problem. However, I did read about a guy who had to reinstall his W7 because of a harddisk failure, and could not access his xp-mode VHD anymore because it demanded re-activation. Thanks. Henk.

  Read the article

• Can't add printer on Windows XP

  - by SuperFurryToad

  I've added a HP 4250 printer to about half a dozen Windows XP PCs in our office without any problems whatsoever, but for some reason I haven't been able to add it to one particular PC today. I go through the Add Printer wizard to add a local printer attached to the PC, enter the new port number as a Standard TCP/IP Port, install the driver. At the end of the wizard I get the following error message: Full error message: "windows cannot connect to the printer. either the printer name was typed incorrectly, or the specified printer has lost its connection to the server." This doesn't make any sense as I am able to ping the printer from the PC. The print spooler is running, and any firewall software on the local PC is switched off.

  Read the article

• nginx is not using gzip to talk to backend servers

  - by Michael Gorsuch

  Our web servers are running IIS 7 and are configured to compress dynamic and static content. When I hit these servers directly, gzip compression works. I recently placed nginx in front of them, and gzip compression has stopped. I was able to work around this by explicitly enabling gzip compression on nginx itself, but that seems a little inefficient considering I have half a dozen backends and only one active nginx box. It appears that nginx is stripping out the Accept-Encoding header. Does anyone have any advice for how to 'correct' this behavior? A sample configuration: upstream backend { server 127.0.0.1:8080; } server { listen 80; proxy_set_header Host $host; proxy_set_header X-Forwarded-For $proxy_add_x_forwarded_for; location / { proxy_pass http://backend; } }

  Read the article

< Previous Page | 204 205 206 207 208 209 210 211 212 213 214 215  | Next Page >