Search Results

Search found 12751 results on 511 pages for 'interface reimplementatio'.

Page 209/511 | < Previous Page | 205 206 207 208 209 210 211 212 213 214 215 216  | Next Page >

  • Ubuntu box static routing problem

    - by Rafael
    Hello, I'm trying to configure a ubuntu server to be a router. This is my interface configuration (eth2 connects to my WAN, eth0 to my LAN): auto eth2 iface eth2 inet static address 192.168.0.249 netmask 255.255.255.0 gateway 192.168.0.1 broadcast 192.168.0.255 auto eth0 iface eth0 inet static address 192.168.100.1 netmask 255.255.255.0 This is the router information: Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 192.168.100.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0 192.168.0.0 0.0.0.0 255.255.255.0 U 0 0 0 eth2 0.0.0.0 192.168.0.1 0.0.0.0 UG 100 0 0 eth2 And this is dhcp configuration: subnet 192.168.100.0 netmask 255.255.255.0 { range 192.168.100.101 192.168.100.254; option domain-name-servers 201.70.86.133; option routers 192.168.100.1; authoritative; } I'm then connecting a mac os x by cable on eth0. This is en0 interface configuration: en0: flags=8963<UP,BROADCAST,SMART,RUNNING,PROMISC,SIMPLEX,MULTICAST> mtu 1500 ether 00:26:bb:5d:82:b0 inet6 fe80::226:bbff:fe5d:82b0%en0 prefixlen 64 scopeid 0x4 inet 192.168.100.101 netmask 0xffffff00 broadcast 192.168.100.255 media: autoselect (100baseTX <full-duplex>) status: active And this is the routing table: Internet: Destination Gateway Flags Refs Use Netif Expire default 192.168.100.1 UGSc 139 32 en0 10.37.129/24 link#8 UC 2 0 vnic1 10.37.129.2 0:1c:42:0:0:9 UHLWI 0 839 lo0 10.37.129.255 ff:ff:ff:ff:ff:ff UHLWbI 0 4 vnic1 10.211.55/24 link#7 UC 2 0 vnic0 10.211.55.2 0:1c:42:0:0:8 UHLWI 0 840 lo0 10.211.55.255 ff:ff:ff:ff:ff:ff UHLWbI 0 4 vnic0 127 127.0.0.1 UCS 0 0 lo0 127.0.0.1 127.0.0.1 UH 3 507924 lo0 169.254 link#4 UCS 0 0 en0 172.16.42/24 link#10 UC 2 0 vmnet8 172.16.42.1 0:50:56:c0:0:8 UHLWI 0 839 lo0 172.16.42.255 link#10 UHLWbI 1 24 vmnet8 192.168.100 link#4 UC 2 0 en0 192.168.100.1 0:e0:7c:7e:f:99 UHLWI 139 0 en0 777 192.168.100.101 127.0.0.1 UHS 0 0 lo0 192.168.100.255 ff:ff:ff:ff:ff:ff UHLWbI 0 4 en0 192.168.116 link#9 UC 2 0 vmnet1 192.168.116.1 0:50:56:c0:0:1 UHLWI 0 839 lo0 192.168.116.255 ff:ff:ff:ff:ff:ff UHLWbI 0 4 vmnet1 When I ping 192.168.100.1, it works. When I ping 192.168.0.249, it also works. However, when I try to ping 192.168.0.1 it does not. Does anyone has any way to solve this? Is there a way to debug it? Thanks,

    Read the article

  • NetworkManager applet looks like it can't see network

    - by amorfis
    My system is Ubuntu 9.04. There is NetworkManager applet, but it looks like there are no networks. When I click it, there is disabled menu "Wired Network/device not managed". I have working eth0 interface, internet is working fine and I can see eth0 in ifconfig When I right-click and choose "Edit connections", there is only "Auto vboxnet0" under "Wired" tab. No "eth0". It shouldn't be a problem, but I cannot connect to VPN because of this :(

    Read the article

  • Telnet or SSH to Embedded Linux based NAS?

    - by ef2011
    Do you happen to know whether it is possible to telnet or SSH to LG N1A1DD1 NAS? It seems to have lots of features that I don't need (including FTP) but I couldn't find any mention of the ability to telnet or SSH to it. If telneting or SSH-ing to it isn't possible, do you know whether it is possible to configure via its web interface a script that can periodically back it up via its USB port? (while still functioning as NAS, of course)

    Read the article

  • Bookshelf viewer for Windows

    - by kokbira
    Once upon a time I used a Linux distro (I don't remember which one) and I could see files and folders in an interesting viewer mode: a bookshelf. I'm searching a software for Windows that does that, but I don't found it yet. I found that ones: FilePro Windirstat They do the work well, but I would like a more-friendly interface, more like a real bookshelf :) - i.e., not a common sequoia viewer AlternativeTo mentioned software.

    Read the article

  • How to make the PC speaker beep from the Windows 7 command prompt?

    - by oKtosiTe
    I'm running some lengthy video encodes using the Handbrake command line interface. After all my encodes are done, I would like to have the PC speaker beep, as I usually turn my large external speakers off. On Linux I would install the "beep" package, but so far I haven't found such a program for Windows 7. Possibly related links: System "Beep" sound does not function in Windows Vista x64 with HD Audio devices (I am indeed using an HD Audio device: the SoundMAX ADI1986A) What’s up with the Beep driver in Windows 7?

    Read the article

  • Collectd agent, Munin master

    - by blauwblaatje
    For monitoring and graphing of servers and services, I would like to make a setup where collectd is the agent, collecting the data on the server, and munin is on the monitoring server, collecting the data from the agents an process it. Reasons for this setup, is that collectd had a smaller footprint on the servers and munin (v2) has a better frontend. I was wondering if there's an interface for this connection, or if someone has an opinion about why I shouldn't do this.

    Read the article

  • CLI Text editor with rtf capabilities for Windows

    - by dassouki
    I'm looking for a command line interface program that gives me the ability to write formatted text easily interoperable with MS Word and OpenOffice. I figured RTF would be the common ground. An example of what I was hoping for would be: [Heading 1] Hello Heading [Paragraph Style 1] My name is hello world, I'm awesome.

    Read the article

  • USB Flash not recognised by Windows and BIOS, but works fine in Linux

    - by bbalegere
    I have a Transcend JetFLash 2GB USB Drive.It was working fine and I had been using it occasionally. All of sudden it stopped working in all versions of Windows . The USB Drive is also not recognised by the BIOS.It does not show in the list of bootable devices.(It used show up in the list earlier) However the USB Drive works fine in my Linux Mint 11 OS. Running dmesg gives this [ 941.812192] usb 1-2: new high speed USB device using ehci_hcd and address 4 [ 941.936178] usb 1-2: device descriptor read/64, error -71 [ 942.164188] usb 1-2: device descriptor read/64, error -71 [ 942.380189] usb 1-2: new high speed USB device using ehci_hcd and address 5 [ 942.504138] usb 1-2: device descriptor read/64, error -71 [ 942.732179] usb 1-2: device descriptor read/64, error -71 [ 942.948154] usb 1-2: new high speed USB device using ehci_hcd and address 6 [ 943.364134] usb 1-2: device not accepting address 6, error -71 [ 943.476172] usb 1-2: new high speed USB device using ehci_hcd and address 7 [ 943.892140] usb 1-2: device not accepting address 7, error -71 [ 943.892191] hub 1-0:1.0: unable to enumerate USB device on port 2 [ 944.296190] usb 2-2: new full speed USB device using uhci_hcd and address 3 [ 944.438251] usb 2-2: not running at top speed; connect to a high speed hub [ 944.709928] usbcore: registered new interface driver uas [ 944.729999] Initializing USB Mass Storage driver... [ 944.730509] scsi6 : usb-storage 2-2:1.0 [ 944.730908] usbcore: registered new interface driver usb-storage [ 944.730917] USB Mass Storage support registered. [ 945.736320] scsi 6:0:0:0: Direct-Access JetFlash Transcend 2GB 8.07 PQ: 0 ANSI: 2 [ 945.744547] sd 6:0:0:0: Attached scsi generic sg1 type 0 [ 945.753316] sd 6:0:0:0: [sdb] 3944448 512-byte logical blocks: (2.01 GB/1.88 GiB) [ 945.758274] sd 6:0:0:0: [sdb] Write Protect is off [ 945.758288] sd 6:0:0:0: [sdb] Mode Sense: 03 00 00 00 [ 945.765167] sd 6:0:0:0: [sdb] No Caching mode page present [ 945.765181] sd 6:0:0:0: [sdb] Assuming drive cache: write through [ 945.784309] sd 6:0:0:0: [sdb] No Caching mode page present [ 945.784323] sd 6:0:0:0: [sdb] Assuming drive cache: write through [ 946.239512] sdb: sdb1 [ 946.257279] sd 6:0:0:0: [sdb] No Caching mode page present [ 946.257292] sd 6:0:0:0: [sdb] Assuming drive cache: write through [ 946.257302] sd 6:0:0:0: [sdb] Attached SCSI removable disk Looks like there is something wrong the USB Drive.It is not recognised in any computer running Windows. Is there any way to fix this? Any idea why this problem occurred ?

    Read the article

  • Arp tries on various *nix based systems.

    - by salparadise
    Does anyone know what determines the amount of arp tries a router will make? I have different behaviors with two devices, if I try to traceroute to a non-existent host on a subnet that belongs to an interface on the router, a Linux box will try to arp 3 times and then return a host un-reacheable icmp message. Junos will continuosly try to arp and not return anything. Is there a sysctl value that determines this or anything at all.

    Read the article

  • Is my Cisco switch port bad?

    - by ewwhite
    I've been chasing a packet-loss and network stability issue for a handful of end-users on an internal network for the past few days... These issues surfaced last week, however the location was struck by lightning six weeks ago. I was seeing 5-10% packet loss between a stack of four Cisco 2960's and several PC's and phones on the other side of a 77-meter run. The PC's were run inline with the phones over a trunked link (switchport configuration pastebin). We were seeing dropped calls and interruptions in client-server applications and Microsoft Exchange connectivity. I tried the usual troubleshooting steps remotely, having a local technician do the following during breaks in user and production activity: change cables between the wall jack and device. change patch cables between the patch panel and switch port(s). try different switch ports within the 2960 stack. change end-user devices with known-good equipment (new phones, different PC's). clear switch port interface counters and monitor incrementing errors closely. (Pastebin output of sh int) Pored over the device logs and Observium RRD graphs. No link up/down issues from the switch side. change power strips on the end-user side. test cable runs from the Cisco 2960 using test cable-diagnostics tdr int Gi4/0/9 (clean)* test cable runs with a Tripp-Lite cable tester. (clean) run diagnostics on the switch stack members. (clean) In the end, it took three changes of switch ports to find a stable solution. The only logical conclusion is that a few Cisco 2960 switch ports are bad or flaky... Not dead, but not consistent in behavior either. I'm not used to seeing individual ports die in this manner. What else can I test or check to determine if these devices are bad? Is it common for single ports to have problems, rather than a contiguous bank of ports? BTW - show cable-diagnostics tdr int Gi4/0/14 is very cool... Interface Speed Local pair Pair length Remote pair Pair status --------- ----- ---------- ------------------ ----------- -------------------- Gi4/0/14 1000M Pair A 79 +/- 0 meters Pair B Normal Pair B 75 +/- 0 meters Pair A Normal Pair C 77 +/- 0 meters Pair D Normal Pair D 79 +/- 0 meters Pair C Normal

    Read the article

  • Why might one host be unable to access the Internet, when it can ping the router and when all other hosts can?

    - by user1444233
    I have a Draytek Vigor 2830n. It's kicking out a 192.168.3.0 LAN. It performs load-balancing across dual-WAN ports, although I've turned off the second WAN to simplify testing. There are many hosts on the LAN. All IPs are allocated through DHCP, most freely allocated from the pool, but one or two are bound to NIC MAC addresses. All hosts can access the Internet, save one. That host (192.168.3.100 or 'dot100' for short) gets allocated an IP address (and the right gateway address, DNS server addresses, subnet etc.) dot100 can ping itself. It can ping the gateway, and access the latter's web interface via port 80. It's responsive and loss-free (sustained ping over a couple of minutes reports no data loss). Yet, for some reason that evades me, dot100 can't ping an external IP address or domain name. I suspect it's never been able to, because it was getting some Internet access from a second adaptor (different subnet), but that's now been turned off, which exposed the problem. In dot100, I've tried: two operating systems (Windows 8 and Knoppix), to rule out anti-virus programs etc. two physical adaptors two cables, on each adaptor two IPs (e.g. .100 and .103 assigned by Mac and .26 from the pool) both dynamic and assigned (MAC-bound) DHCP-allocated IPs but none of this experiments yielded any variation in the result. dot100 is a crucial host. It's a file server for the network, so I need it to be reliably allocated a consistent IP. Can anyone offer a potential solution or a way forward with the analysis please? My guess My analysis so far leads me to believe it's a router issue. I've checked the web interface very carefully. There are no filters setup in Firewall - General Setup or Filter Setup. I suspect it's a corrupted internal routing table, but the web UI shows this as the Routing table: Key: C - connected, S - static, R - RIP, * - default, ~ - private * 0.0.0.0/ 0.0.0.0 via 62.XX.XX.X WAN1 * 62.XX.XX.X/ 255.255.255.255 via 62.XX.XX.X WAN1 S 82.YY.YYY.YYY/ 255.255.255.255 via 82.YY.YYY.YYY WAN1 C 192.168.1.0/ 255.255.255.0 directly connected WAN2 C~ 192.168.3.0/ 255.255.255.0 directly connected LAN2

    Read the article

  • Selecting a Color Selector

    - by RCIX
    I'm looking for a nice full featured color selector program, i currently use Color Cop but i feel its missing some features (mainly a nice interface for selecting a color from a spectrum). Does anyone have any other suggestions?

    Read the article

  • Block Skype on Cisco IOS

    - by ensnare
    I'm trying to block skype via policy routing but it's not working ... here's my configuration: class-map match-any block match protocol skype policy-map QoS-Priority-Input class block police 1000000 31250 31250 conform-action drop exceed-action drop violate-action drop policy-map QoS-Priority-Output class block police 1000000 31250 31250 conform-action drop exceed-action drop violate-action drop interface FastEthernet4 description WAN service-policy input QoS-Priority-Input service-policy output QoS-Priority-Output

    Read the article

  • NAS box discs sharing in domain

    - by Murdock
    I got problem with data sharing of my QNAP NAS Box TS-409 Series with 3 x 750 GB disk (in RAID 5) into domain via File server service. This device is designed mainly to be mapped as a network drive and through its own interface are configured users and policies. I'd like to have it bound with domain user accounts a there to set up security and other policies. Thanks for any suggestion.

    Read the article

  • pix 501, static route to d-link router (different subnet)

    - by ra170
    I have pix 501 cisco firewall with internal ip 192.168.10.1. I have connected d-link router (dir-655) to pix 501. The d-link router has internal ip 192.168.0.1 The picture would like something like that: |pix 501| has 192.168.10.1 ip |DIR-655| has 192.168.0.1 ip 1. |cable modem|----|pix 501|-------|DIR-655|-----PC 2. PC--------|pix 501|---------|DIR-655| | | |cable modem| When I'm on the wireless network (dir-655) with assigned ip of 192.168.0.x I can cross the subnet and connect to my firewall 192.168.10.1. (pic. 1) The problem is that if I'm on the 192.168.10.x network I can't connect to anything over at 192.168.0.x network. (pic.2) I've tried entering a static route like this: `route inside 192.168.0.0 255.255.255.0 192.168.10.1 1` I also tried assigning static ip to wan interface on DIR-655 to 192.168.10.30 and then tried this: route inside 192.168.0.0 255.255.255.0 192.168.10.30 1 But still, can't connect to 192.168.0.1 or anything on that subnet. Is there a way to setup a static route? Would adding a separate router between PIX 501 and DIR-655 help? I would think that static route like this should take care of it, but it doesn't. This is my route config and nat: (config)# sh route outside 0.0.0.0 0.0.0.0 (outside_IP) 1 DHCP static outside (outside_IP) 255.255.248.0 (outside_IP) 1 CONNECT static inside 192.168.0.0 255.255.255.0 192.168.10.1 1 OTHER static inside 192.168.10.0 255.255.255.0 192.168.10.1 1 CONNECT static or (route inside 192.168.0.0 255.255.255.0 192.168.10.30 1) (config)# sh nat nat (inside) 1 192.168.1.0 255.255.255.0 0 0 nat (inside) 1 192.168.10.0 255.255.255.0 0 0 nat (inside) 1 0.0.0.0 0.0.0.0 0 0 I ended up turning DIR-655 into an Access Point (turning off DHCP and pluging cable from PIX lan interface into one of the LAN interfaces on DIR-655, and leaving WAN port empty), that works as far as DIR-655 being on the same subnet now, and I can access every machine. However the question is, why can't I simply route between those two? would router between these two help? One of the reasons is, that the PIX 501 has only 10 licences, so now I'm using almost all of them. (I have few computers, iphones, ps3, print server, etc.) I would really appreciate some help! Thanks.

    Read the article

  • Does Windows 7 allow advanced skinning like Windows XP?

    - by Vilx-
    The Windows 7 Aero interface looks great, but after looking at it for months it gets boring. So I was wondering - is it possible to create advanced skins for Windows 7 that use full Aero capabilities but are redesigned from ground up, including common controls, animations, effects, etc? Windows XP allowed that, although only with a patched uxtheme.dll. Or do you have to implement a custom shell for that?

    Read the article

  • View Centreon graph data

    - by Rich
    Is there a way to view the data that Centreon uses to build graphs, from within the Centreon web interface? We have some gaps in some of our graphs, and I would like to see if it is a problem with the data being returned from the NRPE plugins. I have seen the MonitoringEvent Logs section, but I can't get that to show the returned string and status for each call to a particular plugin, which is what I'd like. Is there a hidden function to do this? Thanks in advance

    Read the article

  • Why is the Windows UI responds slowly after being idle for a long time?

    - by John Isaiah Carmona
    I open these applications in my desktop computer: Visual Studio 2010 Professional IBM Lotus Notes Google Chrome And when it is idle for an hour and I restore the windows, the user interface responds very slowly. My computer auto-lock itself after being idle for 5 minutes. I also minimize the applications using a docklet (RocketDock). Why is it slowing down and how can I prevent it from slowing? My OS is Windows XP Professional SP3, Pentum(R) Dual Core @ 2.80 GHz, 1.99 GB of RAM.

    Read the article

  • Manage internet connection for a programm

    - by michel
    I'am using a Windows 7 pc with 2 networkcards one for public line and one for internal line behind proxy. is there a way or a software programm where i can manage wich programm(outlook, WM) use wich internet connection or networkcard use the option of interface metric is not where i was looking for. someone also suggest me Zonealarm. but i dislike this programm. thx

    Read the article

< Previous Page | 205 206 207 208 209 210 211 212 213 214 215 216  | Next Page >