Search Results

Search found 16894 results on 676 pages for 'block device'.

Page 210/676 | < Previous Page | 206 207 208 209 210 211 212 213 214 215 216 217  | Next Page >

• Can't set-up Wifi Adhoc on my Raspberry Pi with an USB dongle

  - by Wouter

  I am trying to set-up an access point (ad-hoc) for my Raspberry Pi. That means I'm trying to "share" the ethernet connection over Wi-Fi. I am doing this using my Ralink Technology, Corp. RT2501/RT2573 Wireless Adapter. When following a tutorial (or actually every tutorial), it immediately goes wrong. root@pinkypi:/home/pi# iwconfig wlan0 mode ad-hoc Error for wireless request "Set Mode" (8B06) : SET failed on device wlan0 ; Device or resource busy. I already tried ifdown and not having it in the USB port at the startup. If it helps, every action with the thing fail (or at least setting the mode). I am using Debian. I'm sure I'm overseeing something, but I can't find out what. What is wrong?

  Read the article

• Ethernet interface number changed, and old one does not exist, but does not leave IP address

  - by Sagar

  I have a virtual machine with Mandriva 2007.0 (yes, old - unfortunately we do not have a choice here). Anyway, the problem: Before reboot: active network interface = eth0. No other interfaces present, and network manager confirms this. Static IP address set to 172.31.2.22. No issues, everything working properly, routing et al. -------Reboot--------- After reboot: active network interface = eth1, with a DHCP address. Network manager shows eth0 as disconnected, and not connectable. When I try to set eth1 up with the static IP address (same one), it says "In Use". I then tried ifconfig eth0 172.31.2.29 just to free it up from the eth0 interface so I could use it with eth1 (since this is connected). Result: ifconfig eth0 172.31.2.29 SIOCSIFADDR: No such device eth0: unknown interface: No such device Nothing else changed. Any ideas what could be happening, or at least how I can get my IP address back?

  Read the article

• TP-Link TL-WA701N not working good as wireless extender

  - by djechelon

  I bought the device in subject to extend the range of my WPA2/PSK-protected wifi network powered by a TP-Link TL-WR340G device (AP+router). I configured it as follows: Operation mode: Universal Repeater MAC of AP: scanned my SSID and got it Channel width: 20MHz Security options: the same as the parent AP (WPA2/PSK with AES encryption) After configuration inSSIDer shows me two APs beaconing the same SSID at different SNRs (because I was with my laptop close to the extender). After a few hours my tablet, far from the parent AP, stopped working. I found that the scan reported two networks with the same SSID: one WPA-protected and one free at all. This happened very frequently. Rebooting the extender by unplugging it worked but this doesn't last long. Sometimes the extender stops transmitting at all, sometimes it beacons an open network to which nobody can connect (because there is no DHCP). What's wrong with my configuration?

  Read the article

• Returning "200 OK" in Apache on HTTP OPTIONS requests

  - by i.

  I'm attempting to implement cross-domain HTTP access control without touching any code. I've got my Apache(2) server returning the correct Access Control headers with this block: Header set Access-Control-Allow-Origin "*" Header set Access-Control-Allow-Methods "POST, GET, OPTIONS" I now need to prevent Apache from executing my code when the browser sends a HTTP OPTIONS request (it's stored in the REQUEST_METHOD environment variable), returning 200 OK. How can I configure Apache to respond "200 OK" when the request method is OPTIONS? I've tried this mod_rewrite block, but the Access Control headers are lost. RewriteEngine On RewriteCond %{REQUEST_METHOD} OPTIONS RewriteRule ^(.*)$ $1 [R=200,L]

  Read the article

• WinXP How to Tunnel LPT over USB

  - by Michael Pruitt

  I have a windows program that accesses a device connected to a LPT (1-3) 25 pin port. The communication is bidirectional, and I suspected the control lines are also accessed directly. I would like to migrate the device to a machine that does not have a LPT port. I saw the dos2usb software, but that takes the output (from a DOS program) and 'prints' it formatted for a specific printer. I need a raw LPT connection, and a cable that provides access to all the control signals. I do have a USB to 36-pin Centronics that may have the extra signals. I use it with a vinyl cutter that doesn't like most of the USB dongles. It comes up as USB001. Would adding and sharing a generic printer, then mapping LPT1 to the share get me closer? Would that work for a parallel port scanner? My preferred solution is a USB cable with a driver that will map it to LPT1, LPT2, or LPT3.

  Read the article

• How to get headphones and speakers working at the same time?

  - by Borek

  I have a Gigabyte P55-UD3 motherboard which comes with a Realtek sound card and audio header for the front panel. My headset is permanently connected to the front panel (mic in, headphones in) and I also have speakers connected at the rear of the computer. What I want to achieve is that both the headphones and the speakers work at the same time. On my old PC with Realtek, I was able to do this by clicking "Device advanced settings" in the Realtek HD Audio Manager and then clicking "Make front and rear output devices playback two different audio streams simultaneously" and then doing some reassigning of front/rear settings in the Realtek Audio Manager (can't remember the details). But that doesn't seem to be working now - either the speakers play sounds or the headphones, not both at the same time. To pose the question differently, Windows plays the sounds on the "default device". I'd like to make both headphones and the speakers kind of like the default devices.

  Read the article

• Why is this LTO4 Tape-drive not working

  - by Tim Haegele

  # modprobe mptsas # dmesg [ 4274.796796] scsi target7:0:0: mptsas: ioc1: delete device: fw_channel 0, fw_id 0, phy 0, sas_addr 0x50050763124b29ac [ 4274.939579] mptsas 0000:01:00.0: PCI INT A disabled [ 4280.934531] Fusion MPT SAS Host driver 3.04.12 [ 4280.934552] mptsas 0000:01:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 4280.934692] mptbase: ioc2: Initiating bringup [ 4281.490183] ioc2: LSISAS1064E B3: Capabilities={Initiator} [ 4281.490203] mptsas 0000:01:00.0: setting latency timer to 64 [ 4293.555274] scsi8 : ioc2: LSISAS1064E B3, FwRev=011e0000h, Ports=1, MaxQ=277, IRQ=16 [ 4293.574906] mptsas: ioc2: attaching ssp device: fw_channel 0, fw_id 0, phy 0, sas_addr 0x50050763124b29ac [ 4293.576471] scsi 8:0:0:0: Sequential-Access IBM ULTRIUM-HH4 B6W1 PQ: 0 ANSI: 6 [ 4293.578549] st 8:0:0:0: Attached scsi tape st0 [ 4293.578550] st 8:0:0:0: st0: try direct i/o: yes (alignment 512 B) [ 4293.578577] st 8:0:0:0: Attached scsi generic sg5 type 1 # mt -f /dev/st0 status mt -f /dev/st0 status mt: /dev/st0: rmtopen failed: Input/output error # dd if=/dev/zero of=/dev/nst0 bs=1024 count=10 dd: opening `/dev/nst0': Input/output error I am running debian squeeze 2.6.32-5-amd64 #1 SMP Sun May 6 04:00:17 UTC 2012 x86_64 GNU/Linux Server is Fujitsu TX140 with Controller Symbios Logic SAS1064ET PCI-Express Fusion-MPT SAS Tape+Hardware is new.

  Read the article

• List all devices of system

  - by pareshverma91

  In my understanding linux can list only those devices which it can understand, i.e. for which the drivers have been installed. I think lspci is the command for that. But how can one figure out if there exists some device in the system for which the drivers are not installed and perhaps some hint about what that device is for and what driver would suffice for it. I would like to know this info so as to be able to recompile my linux kernel to a minimum and would like to avoid a hit and trial approach.

  Read the article

• Live noise-filter on line-in

  - by Damon Gant

  I'm running the following setup: Xbox 360 is hooked up to my (PC) screen via HDMI/DVI converter. Because the Xbox has no dedicated sound output, except for optical S/PIDF, I'm also using the AV/RCA output, namely just the audio, which is connected to an old stereo, which is then connected to my PCs line-in. I'm now experiencing a some of noise. I'm using one of the standard "Realtek High Definition Audio" cards, which doesn't seem to offer this kind of functionality. Is there a software that will playback audio right off a device while running filters on it? It doesn't have to create a device on its own, I just want to listen to it. Here's a sample: http://puu.sh/1suY6

  Read the article

• 12.04 ext4 - cannot create regular file/No space left - with a lot of space and inodes

  - by user1434058

  This seems similar: EXT4 "No space left on device (28)" incorrect but there is no explanation I created an ext4 filesystem on a RAID 1 array with: mke2fs -t ext4 -T small /dev/md0 Copying a single directory with many tiny files I get: cp: cannot create regular file `/mnt/raid1_new/pics/pic3412.jpg': No space left on device space used 5% inodes used 1% I manually tried: cp /source/test1.jpg /mnt/raid1_new/pics/test1.jpg --- error cp /source/test1.jpg /mnt/raid1_new/pics/test2.jpg --- ERROR cp /source/test1.jpg /mnt/raid1_new/pics/test3.jpg --- no error Notes: RAID 1 disks are error free. I tried mv instead of cp and got the same thing. I tried omitting -T small with no effect Can somebody help me understand this magic?

  Read the article

• difference between IRQ and Interrupt Priority level

  - by Tony

  Can someone tell me if the IRQ of a device is different to the Interrupt Priority level?

  Read the article

• Remote call script as administrator

  - by drupality

  I created a Windows XP bat script to modify etc/hosts file. I want to share this script at other machine, then from another computer I want to invoke these script to modify hosts file at first computer (via LAN). I need some example. I didn't find any example. Is this possible? I try: runas/user:username block.bat On the same machine login as guest but it doesn't work. No errors just "Attempting to call block.bat" and end of invocation. As admin script works ok. Could someone give me any advice?

  Read the article

• Windows Vista wont recognize SSD drive

  - by Spiros

  I just bought an SSD drive for my Vista (32bit) box (120GB OCZ Agility 3). Unfortunately windows vista won't display it in the my computer window, and generally wont let me work on it. However, the bios recognizes the SSD drive correctly, and when I go on the windows device manager the drive is there as well. I can see the device properties. On the volumes, when I click on populate, I have: Disk: Disk1 Type: Uknown Status: not initialized Partition style: not avaiable Unallocated space: 0MB Reserved space: 0MB Any ideas what could be wrong? Thanks

  Read the article

• 1Tb disk formatted on Linux won't mount on windows nor mac

  - by Pedro MC

  I have an external HD (western digital) with 1Tb. I use Linux but I wanted to reserve a cross platform partition on the disk. I decided to create two partitions and used the "disks" application to do it. I created one partition with the LUKS (version 1) encryption and the other one, cross platform, in NTFS filesystem. Things work fine on my OS but when I try to use the disk (the cross platform partition) on both windows and mac the device is not recognized. What could it be? Next, output of "sfdisk -l /dev/sdb": Disk /dev/sdb: 121600 cylinders, 255 heads, 63 sectors/track Units = cylinders of 8225280 bytes, blocks of 1024 bytes, counting from 0 Device Boot Start End #cyls #blocks Id System /dev/sdb1 0+ 36473- 36473- 292968750 83 Linux /dev/sdb2 36473+ 121600- 85128- 683789062+ 83 Linux /dev/sdb3 0 - 0 0 0 Empty /dev/sdb4 0 - 0 0 0 Empty

  Read the article

• How to prevent yourself from commenting on websites?

  - by MHH

  There is a bunch of browser add ons to either block particular websites (i.e. leechblock, chrome nanny or various OS specific solutions) or block the comment section of a website (i.e. commentBlocker). However, what if you want to be able to read the comment section of all websites, but want to never be able to add comments yourself, on particular sites? Is there anything that will allow this? I'm particularly interested in answers that will work for both windows and mac, and will also work for google chrome, firefox, and safari (note they can be different solutions for each browser/operating system)

  Read the article

• Ubuntu server 10.04 doesn't boot into installed Gnome desktop automatically

  - by Tong Wang

  I've installed Ubuntu server 10.04 and then installed Gnome desktop on top of it, because I am new to Linux and its command line, I need the GUI desktop to help me get around. However, the problem I got is that the server doesn't boot into the GUI desktop when powered on. It's booting into a shell like this: Gave up waiting for root device. Common problems: - Boot args (cat /proc/cmdline) - Check rootdelay= (did the system wait long enought?) - check root= (did the system wait for the right device?) - Missing modules (cat /proc/modules; ls /dev) ALERT! /dev/mapper/cecdata-root does not exist. Dropping to a shell! BusyBox v1.13.3 (Ubuntu 1:1.13.3-1ubuntu11) built-in shell (ash) Enter 'help' for a list of built-in commands. (initramfs) result of (cat /proc/cmdline) BOOT_IMAGE=/vmlinuz-2.6.32-28-server root=/dev/mapper/cecdata-root ro quiet Then I have type "exit" to exit the shell and then it boots into Gnome. Any idea what's wrong? Edit: add output for the following commands wt@cecdata:~$ ls /dev/mapper/ cecdata-root cecdata-swap_1 control wt@cecdata:~$ fdisk -l wt@cecdata:~$ wt@cecdata:~$ cat /etc/fstab # /etc/fstab: static file system information. # # Use 'blkid -o value -s UUID' to print the universally unique identifier # for a device; this may be used with UUID= as a more robust way to name # devices that works even if disks are added and removed. See fstab(5). # # <file system> <mount point> <type> <options> <dump> <pass> proc /proc proc nodev,noexec,nosuid 0 0 /dev/mapper/cecdata-root / ext4 errors=remount-ro 0 1 # /boot was on /dev/sda1 during installation UUID=1635be41-d025-405e-b4a3-6f0abedb7aab /boot ext2 defaults 0 2 /dev/mapper/cecdata-swap_1 none swap sw 0 0 wt@cecdata:~$ Adding output for lsmod wt@cecdata:~$ lsmod Module Size Used by fbcon 39270 71 tileblit 2487 1 fbcon font 8053 1 fbcon bitblit 5811 1 fbcon softcursor 1565 1 bitblit dell_wmi 2177 0 dcdbas 6918 0 vga16fb 12757 1 vgastate 9857 1 vga16fb psmouse 64576 0 serio_raw 4950 0 power_meter 9473 0 bnx2 72874 0 lp 9336 0 parport 37160 1 lp mptsas 50592 2 usbhid 41116 0 mptscsih 37167 1 mptsas hid 83568 1 usbhid mptbase 91674 2 mptsas,mptscsih scsi_transport_sas 33021 1 mptsas

  Read the article

• Cant access a remote server due mistake by setting firewall rule

  - by LMIT

  I need help due a my silly mistake! So for long time i have a dedicate server hosted by register.it Usually i access remotly to this server (Windows 2008 server) by Terminal Server. Today i wanted to block one site that continually send request to my server. So i was adding a new rule in the firewall (the native firewall on windows 2008 server), as i did many time, but this time, probably i was sleeping with my brain i add a general rules that stop everything! So i cant access to the server anymore, as no any users can browse the sites, nothing is working because this rule block everything. I know that is a silly mistake, no need to tell me :) so please what i can do ? The only 1 thing that my provider let me is reboot the server by his control panel, but this not help me in any way because the firewall block me again. i have administrator username and password, so what i really can do ? there are some trick some tecnique, some expert guru that can help me in this very bad situation ? UPDATE i follow the Tony suggest and i did a NMAP to check if some ports are open but look like all closed: NMAP RESULT Starting Nmap 6.00 ( http://nmap.org ) at 2012-05-29 22:32 W. Europe Daylight Time NSE: Loaded 93 scripts for scanning. NSE: Script Pre-scanning. Initiating Parallel DNS resolution of 1 host. at 22:32 Completed Parallel DNS resolution of 1 host. at 22:33, 13.00s elapsed Initiating SYN Stealth Scan at 22:33 Scanning xxx.xxx.xxx.xxx [1000 ports] SYN Stealth Scan Timing: About 29.00% done; ETC: 22:34 (0:01:16 remaining) SYN Stealth Scan Timing: About 58.00% done; ETC: 22:34 (0:00:44 remaining) Completed SYN Stealth Scan at 22:34, 104.39s elapsed (1000 total ports) Initiating Service scan at 22:34 Initiating OS detection (try #1) against xxx.xxx.xxx.xxx Retrying OS detection (try #2) against xxx.xxx.xxx.xxx Initiating Traceroute at 22:34 Completed Traceroute at 22:35, 6.27s elapsed Initiating Parallel DNS resolution of 11 hosts. at 22:35 Completed Parallel DNS resolution of 11 hosts. at 22:35, 13.00s elapsed NSE: Script scanning xxx.xxx.xxx.xxx. Initiating NSE at 22:35 Completed NSE at 22:35, 0.00s elapsed Nmap scan report for xxx.xxx.xxx.xxx Host is up. All 1000 scanned ports on xxx.xxx.xxx.xxx are filtered Too many fingerprints match this host to give specific OS details TRACEROUTE (using proto 1/icmp) HOP RTT ADDRESS 1 ... ... ... 13 ... 30 NSE: Script Post-scanning. Read data files from: D:\Program Files\Nmap OS and Service detection performed. Please report any incorrect results at http://nmap.org/submit/ . Nmap done: 1 IP address (1 host up) scanned in 145.08 seconds Raw packets sent: 2116 (96.576KB) | Rcvd: 61 (4.082KB) Question: The provider locally can access by username and password ?

  Read the article

• Windows does not detect any modems anymore[HSPA]

  - by Shenal Silva

  By an accident i uninstalled my Connect manager (ZTE). but when i re-install it the virtual CD drive is detected but it does not detect the drivers. When i direct to the folder containing the relevant drivers(.sys files) still it doesnt detect. Then i tried a modem of a different brand Huawei the same problem presists As i understand it is not a device(brand) driver specific issue as it does not detect modem(dongles) of any brand. when i plugged in a different USB device(a pen drive) the driver is detected and it works perfectly. Please help me with the issue i have tried system restore but it doesnt work. I want a repair that works without re-installing windows [Edit] I tried Karan's suggested method with usboblivion it didnt work. now im sure that the issue does not deal with the registry

  Read the article

• How can I change the amount of video memory with a Mobile Intel 4 Series Express Chipset?

  - by user45924

  I have the chipset in the title. The Intel control panel says the following: Intel® Graphics Media Accelerator Driver for Mobile Report Report Date: 8/11/2010 Report Time[hr:mm:ss]: 20:2:54 Driver Version: 8.15.10.2182 Operating System: Windows 7 (6.1.7600) Default Language: English (Canada) DirectX* Version: 10.0 Physical Memory: 3963 MB Minimum Graphics Memory: 128 MB Maximum Graphics Memory: 1759 MB Graphics Memory in Use: 17 MB Processor: Intel64 Family 6 Model 23 Stepping 10 Processor Speed: 1995 MHz Vendor ID: 8086 Device ID: 2A42 Device Revision: 07 Even while playing games, the Graphics Memory in Use only ever goes up to 26 MB. I've looked in the BIOS; there's nothing there. Is there any way I can force it to go higher? Thanks :)

  Read the article

• Public IP Routing over Private GRE tunnel

  - by Paul

  I have a GRE tunnel configured between two linux boxes. The tunnel works fine. I can ping from each host the other private ip. Head privateip: 10.0.0.1 publicip: 8.8.8.8 Tail privateip: 10.0.0.2 publicip: 7.7.7.7 The public IP on Tail has the network block 9.9.9.0/23 statically routed over the 7.7.7.7 interface. The idea is to make the 9.9.9.0/23 ips work on servers on the 8.8.8.8 network. I configure the tail host to route the /23 block. I mounted a 9.9 IP on the head server. I can ping the 9.9 ip from the tail to the head. I can't ping the 9.9 ip from the public internet. I think I need to add some other routes because of gateway issues, but I can't seem to wrap my mind around it (not a router guy, just beating my way through something that I have never done before and vaguely understand) --danks

  Read the article

• second ip address on the same interface but on a different subnet

  - by fptstl

  Is it possible in CentOS 5.7 64bit to have a second IP address on one interface (eg. eth0) - alias interface configuration - in a different subnet? Here is the original config for eth0 more etc/sysconfig/network-scripts/ifcfg-eth0 # Broadcom Corporation NetXtreme BCM5721 Gigabit Ethernet PCI Express DEVICE=eth0 BOOTPROTO=static BROADCAST=192.168.91.255 HWADDR=00:1D:09:FE:DA:04 IPADDR=192.168.91.250 NETMASK=255.255.255.0 NETWORK=192.168.91.0 ONBOOT=yes And here is the config for eth0:0 more etc/sysconfig/network-scripts/ifcfg-eth0:0 # Broadcom Corporation NetXtreme BCM5721 Gigabit Ethernet PCI Express DEVICE=eth0:0 BOOTPROTO=static BROADCAST=10.10.191.255 DNS1=10.10.15.161 DNS2=10.10.18.36 GATEWAY=10.10.191.254 HWADDR=00:1D:09:FE:DA:04 IPADDR=10.10.191.210 NETMASK=255.255.255.0 NETWORK=10.39.191.0 ONPARENT=yes How would the resolv.conf file should change since there are two different gateways? Any other change needed?

  Read the article

• Importing GPG Key

  - by Bodo

  I have problems importing my GPG-Keys into my new installation of debian. I exportet the private-key a few years ago. Now I am trying to get everything running under a new debian. I tried to do gpg --allow-secret-key-import --import private-key.asc But I only get this: gpg: Keine gültigen OpenPGP-Daten gefunden. gpg: Anzahl insgesamt bearbeiteter Schlüssel: 0 which translates to: gpg: No valid OpenPGP-Data found gpg: Number of processed Keys : 0 The file looks correct and starts with --BEGIN PGP PRIVATE KEY BLOCK----- Version: GnuPG v1.4.9 (GNU/Linux) and ends with -----END PGP PRIVATE KEY BLOCK----- what could be wrong?

  Read the article

• Aruba Wireless Controller 200 and AP70 manual

  - by techie

  I have an Aruba wireless system that is currently in use but there is no documentation from the previous person in charge. I have no manuals or login information for the wireless controllers and APs. I checked the Aruba website and you need to register to access the support information but registration isn't instant and takes several days. I've waited for quite a while now and have tried googling and checking the Aruba forums but have found no indication of a manual. What I really need is the ability to reset the controller and APs so I can access the device with the default username and password. There is no reset button on this device so I have no idea how you go about resetting the controller and APs. Hm it seems I can't create a new tag as a new user. If possible can someone add an "Aruba" tag?

  Read the article

• Fix bad blocks on Mac hard disk

  - by Andrew Vit

  I have a hard disk that I scanned with TechTool and it reports one bad block. As far as I can tell, TechTool only scans and reports a failure. It doesn't fix anything. Back in the day, Norton Disk Doctor did the job of scanning and flagging (remapping) bad blocks on the Mac. Today we have various tools for fixing up HFS+ directory errors (Disk Utility, fsck, DiskWarrior, TechTool), but I don't know of any tool that will do a surface scan and fix the bad blocks too. What software is available for this? If I know the address of the bad block, is there a low-level terminal utility for marking it?

  Read the article

• Archlinux/atheros WLAN configuration troubles

  - by GrinReaper

  I'm trying to config archlinux to use my wireless network adapter. It's quite troublesome. From what I've gathered, it's an atheros network adapter, using the ath5k driver/module... I can't get it to work; any ideas? Here's some of the output from my tinkering: # lspci | grep -i net 00:0a.0 Ethernet controller: nVidia corporation MCP67 Ethernet (reva2) 03:00.0 Ethernet controller: atheros communications inc. AR5001 Wireless Network Adapter (rev01) # lsusb ... Bus 004 Device 003: ID 03f0:17d Hewlett Packard Wireless (Bluetooth + WLAN Interface [Integrated Module] # ping -c 3 www.google.com ping: unknown host www.google.com #ping -c 3 8.8.8.8 ping: network is unreachable # lspci -v 03:00.0 Ethernet controller: atheros communications inc. AR5001 Wireless Network Adapter (rev01) ... Kernel driver in use: ath5k Kernel modules: ath5k # dmesg |grep ath5k registered as phy0 registered led device ath5k: atheros chip found PCI INT A disabled registered led device registered as phy1 # ip addr | sed '/^[0-9]/!d;s/: <.*$//' 1: lo 2: eth1 3: eth0 # ip link set <interface> up/down RNETLINK answers: Operation not possible due to RF-kill Also, is there a way to dump text from command-line to a text file so i can just copy pasta? Sorry, first time using a linux distro... EDIT: So I just tried this: I actually just did this twice. (I can't tell which setting is on/off for my wireless adapter. The lights are blue all the time now.) #rfkill list 0: hp-wifi: wireless lan softblocked: no hardblocked :yes 1: hp-bluetooth: bluetooth softblocked: no hardblocked :yes 3: phy1: wireless lan softblocked: no hardblocked :yes #rfkill list 0: hp-wifi: wireless lan softblocked: no hardblocked :no 1: hp-bluetooth: bluetooth softblocked: no hardblocked no 3: phy1: wireless lan softblocked: no hardblocked :yes 7: hci0: bluetooh 0: hp-wifi: wireless lan softblocked: no hardblocked :no I've dug around some other articles and it seems like ath5k is supposed to be preferable to madwifi, so should i be using madwifi? I'm 99% sure I disabled the hardblock (by turning it ON) but, as shown above, phy1 wireless lan is STILL hardblocked. What gives? Maybe I've made some more fundamental error in a basic config file? EDIT: I've fixed the hardblock. I've tried pinging www.google.com, but to no avail. I get: ping: unknown host www.google.com In the arch wiki: Edit /etc/hosts and add the same HOSTNAME you entered in /etc/rc.conf: 127.0.0.1 archlinux.domain.org localhost.localdomain localhost archlinux To my understanding, hostname is just a user-specified and based on preference(?) My /etc/rc.conf: HOSTNAME="gestalt" My /etc/hosts: 127.0.0.1 localhost.localdomain localhost gestalt but should it be the following? 120.0.0.1 localhost.domain.org localhost.localdomain localhost gestalt

  Read the article

< Previous Page | 206 207 208 209 210 211 212 213 214 215 216 217  | Next Page >