Search Results

Search found 16894 results on 676 pages for 'block device'.

Page 213/676 | < Previous Page | 209 210 211 212 213 214 215 216 217 218 219 220  | Next Page >

  • eMail with Conflicting Headers not blocked in MS365

    - by John Meredith Langstaff
    On occasion, a company receives eMail with two header fields (“Received” and “From”) containing data that contradict each other drastically. Should they not expect their anti-spam system to flag or block items with contradictions in these fields? For example, they received an eMail which contained [almost exactly] these two headers: Received: from [107.52.51.26] by web315204.mail.ne1.yahoo.com via HTTP; Mon,28 Oct 2013 04:28:04 PDT From: Barry Smith [email protected] Obviously, eMail from an @att.net address isn’t coming from a server on the domain yahoo.com, and Yahoo isn’t forwarding AT&T’s eMail. There were no other headers indicating that the item was sent “OnBehalfOf”, or “Forwarded-by”, or “By_Proxy” or any other such. Should I write a utility to scan incoming eMail for such conflicts, or look more closely at their spam filtering to block this kind of eMail? Their eMail system is Hosted Exchange on MS-365. My central question is, where specifically do I look in MS-365 to get this type of conflicted eMail blocked?

    Read the article

  • Switching from Amazon EC2 instance-store to EBS Volume

    - by Adam
    Hi, I have an Amazon EC2 instance that is using an instance-store as its root device. It has no EBS volumes attached to it. It has a database and a running web application on it. If I understand correctly this is a bad setup as I would lose all the data on the instance if it were to reboot. I would like to correct this mistake. I'd like to move all the data on the running instance to a new EBS volume and make that new volume the root device. How do I go about doing this? Thanks!

    Read the article

  • Degraded RAID5 and no md superblock on one of remaining drive

    - by ark1214
    This is actually on a QNAP TS-509 NAS. The RAID is basically a Linux RAID. The NAS was configured with RAID 5 with 5 drives (/md0 with /dev/sd[abcde]3). At some point, /dev/sde failed and drive was replaced. While rebuilding (and not completed), the NAS rebooted itself and /dev/sdc dropped out of the array. Now the array can't start because essentially 2 drives have dropped out. I disconnected /dev/sde and hoped that /md0 can resume in degraded mode, but no luck.. Further investigation shows that /dev/sdc3 has no md superblock. The data should be good since the array was unable to assemble after /dev/sdc dropped off. All the searches I done showed how to reassemble the array assuming 1 bad drive. But I think I just need to restore the superblock on /dev/sdc3 and that should bring the array up to a degraded mode which will allow me to backup data and then proceed with rebuilding with adding /dev/sde. Any help would be greatly appreciated. mdstat does not show /dev/md0 # cat /proc/mdstat Personalities : [linear] [raid0] [raid1] [raid10] [raid6] [raid5] [raid4] [multipath] md5 : active raid1 sdd2[2](S) sdc2[3](S) sdb2[1] sda2[0] 530048 blocks [2/2] [UU] md13 : active raid1 sdd4[3] sdc4[2] sdb4[1] sda4[0] 458880 blocks [5/4] [UUUU_] bitmap: 40/57 pages [160KB], 4KB chunk md9 : active raid1 sdd1[3] sdc1[2] sdb1[1] sda1[0] 530048 blocks [5/4] [UUUU_] bitmap: 33/65 pages [132KB], 4KB chunk mdadm show /dev/md0 is still there # mdadm --examine --scan ARRAY /dev/md9 level=raid1 num-devices=5 UUID=271bf0f7:faf1f2c2:967631a4:3c0fa888 ARRAY /dev/md5 level=raid1 num-devices=2 UUID=0d75de26:0759d153:5524b8ea:86a3ee0d spares=2 ARRAY /dev/md0 level=raid5 num-devices=5 UUID=ce3e369b:4ff9ddd2:3639798a:e3889841 ARRAY /dev/md13 level=raid1 num-devices=5 UUID=7384c159:ea48a152:a1cdc8f2:c8d79a9c With /dev/sde removed, here is the mdadm examine output showing sdc3 has no md superblock # mdadm --examine /dev/sda3 /dev/sda3: Magic : a92b4efc Version : 00.90.00 UUID : ce3e369b:4ff9ddd2:3639798a:e3889841 Creation Time : Sat Dec 8 15:01:19 2012 Raid Level : raid5 Used Dev Size : 1463569600 (1395.77 GiB 1498.70 GB) Array Size : 5854278400 (5583.08 GiB 5994.78 GB) Raid Devices : 5 Total Devices : 4 Preferred Minor : 0 Update Time : Sat Dec 8 15:06:17 2012 State : active Active Devices : 4 Working Devices : 4 Failed Devices : 1 Spare Devices : 0 Checksum : d9e9ff0e - correct Events : 0.394 Layout : left-symmetric Chunk Size : 64K Number Major Minor RaidDevice State this 0 8 3 0 active sync /dev/sda3 0 0 8 3 0 active sync /dev/sda3 1 1 8 19 1 active sync /dev/sdb3 2 2 8 35 2 active sync /dev/sdc3 3 3 8 51 3 active sync /dev/sdd3 4 4 0 0 4 faulty removed [~] # mdadm --examine /dev/sdb3 /dev/sdb3: Magic : a92b4efc Version : 00.90.00 UUID : ce3e369b:4ff9ddd2:3639798a:e3889841 Creation Time : Sat Dec 8 15:01:19 2012 Raid Level : raid5 Used Dev Size : 1463569600 (1395.77 GiB 1498.70 GB) Array Size : 5854278400 (5583.08 GiB 5994.78 GB) Raid Devices : 5 Total Devices : 4 Preferred Minor : 0 Update Time : Sat Dec 8 15:06:17 2012 State : active Active Devices : 4 Working Devices : 4 Failed Devices : 1 Spare Devices : 0 Checksum : d9e9ff20 - correct Events : 0.394 Layout : left-symmetric Chunk Size : 64K Number Major Minor RaidDevice State this 1 8 19 1 active sync /dev/sdb3 0 0 8 3 0 active sync /dev/sda3 1 1 8 19 1 active sync /dev/sdb3 2 2 8 35 2 active sync /dev/sdc3 3 3 8 51 3 active sync /dev/sdd3 4 4 0 0 4 faulty removed [~] # mdadm --examine /dev/sdc3 mdadm: No md superblock detected on /dev/sdc3. [~] # mdadm --examine /dev/sdd3 /dev/sdd3: Magic : a92b4efc Version : 00.90.00 UUID : ce3e369b:4ff9ddd2:3639798a:e3889841 Creation Time : Sat Dec 8 15:01:19 2012 Raid Level : raid5 Used Dev Size : 1463569600 (1395.77 GiB 1498.70 GB) Array Size : 5854278400 (5583.08 GiB 5994.78 GB) Raid Devices : 5 Total Devices : 4 Preferred Minor : 0 Update Time : Sat Dec 8 15:06:17 2012 State : active Active Devices : 4 Working Devices : 4 Failed Devices : 1 Spare Devices : 0 Checksum : d9e9ff44 - correct Events : 0.394 Layout : left-symmetric Chunk Size : 64K Number Major Minor RaidDevice State this 3 8 51 3 active sync /dev/sdd3 0 0 8 3 0 active sync /dev/sda3 1 1 8 19 1 active sync /dev/sdb3 2 2 8 35 2 active sync /dev/sdc3 3 3 8 51 3 active sync /dev/sdd3 4 4 0 0 4 faulty removed fdisk output shows /dev/sdc3 partition is still there. [~] # fdisk -l Disk /dev/sdx: 128 MB, 128057344 bytes 8 heads, 32 sectors/track, 977 cylinders Units = cylinders of 256 * 512 = 131072 bytes Device Boot Start End Blocks Id System /dev/sdx1 1 8 1008 83 Linux /dev/sdx2 9 440 55296 83 Linux /dev/sdx3 441 872 55296 83 Linux /dev/sdx4 873 977 13440 5 Extended /dev/sdx5 873 913 5232 83 Linux /dev/sdx6 914 977 8176 83 Linux Disk /dev/sda: 1500.3 GB, 1500301910016 bytes 255 heads, 63 sectors/track, 182401 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Device Boot Start End Blocks Id System /dev/sda1 * 1 66 530113+ 83 Linux /dev/sda2 67 132 530145 82 Linux swap / Solaris /dev/sda3 133 182338 1463569695 83 Linux /dev/sda4 182339 182400 498015 83 Linux Disk /dev/sda4: 469 MB, 469893120 bytes 2 heads, 4 sectors/track, 114720 cylinders Units = cylinders of 8 * 512 = 4096 bytes Disk /dev/sda4 doesn't contain a valid partition table Disk /dev/sdb: 1500.3 GB, 1500301910016 bytes 255 heads, 63 sectors/track, 182401 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Device Boot Start End Blocks Id System /dev/sdb1 * 1 66 530113+ 83 Linux /dev/sdb2 67 132 530145 82 Linux swap / Solaris /dev/sdb3 133 182338 1463569695 83 Linux /dev/sdb4 182339 182400 498015 83 Linux Disk /dev/sdc: 1500.3 GB, 1500301910016 bytes 255 heads, 63 sectors/track, 182401 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Device Boot Start End Blocks Id System /dev/sdc1 1 66 530125 83 Linux /dev/sdc2 67 132 530142 83 Linux /dev/sdc3 133 182338 1463569693 83 Linux /dev/sdc4 182339 182400 498012 83 Linux Disk /dev/sdd: 2000.3 GB, 2000398934016 bytes 255 heads, 63 sectors/track, 243201 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Device Boot Start End Blocks Id System /dev/sdd1 1 66 530125 83 Linux /dev/sdd2 67 132 530142 83 Linux /dev/sdd3 133 243138 1951945693 83 Linux /dev/sdd4 243139 243200 498012 83 Linux Disk /dev/md9: 542 MB, 542769152 bytes 2 heads, 4 sectors/track, 132512 cylinders Units = cylinders of 8 * 512 = 4096 bytes Disk /dev/md9 doesn't contain a valid partition table Disk /dev/md5: 542 MB, 542769152 bytes 2 heads, 4 sectors/track, 132512 cylinders Units = cylinders of 8 * 512 = 4096 bytes Disk /dev/md5 doesn't contain a valid partition table

    Read the article

  • How to drop all subnets outside of the US using iptables

    - by Jim
    I want to block all subnets outside the US. I've made a script that has all of the US subnets in it. I want to disallow or DROP all but my list. Can someone give me an example of how I can start by denying everything? This is the output from -L Chain INPUT (policy DROP) target prot opt source destination ACCEPT all -- anywhere anywhere ACCEPT all -- anywhere anywhere state RELATED,ESTABLISHED ACCEPT tcp -- anywhere anywhere tcp dpt:ftp state NEW DROP icmp -- anywhere anywhere Chain FORWARD (policy DROP) target prot opt source destination Chain OUTPUT (policy ACCEPT) target prot opt source destination And these are the rules iptables --F iptables --policy INPUT DROP iptables --policy FORWARD DROP iptables --policy OUTPUT ACCEPT iptables -A INPUT -i lo -j ACCEPT iptables -A INPUT -i eth0 -m state --state ESTABLISHED,RELATED -j ACCEPT iptables -A INPUT -p tcp -i eth0 --dport 21 -m state --state NEW -j ACCEPT iptables -A INPUT -p icmp -j DROP Just for clarity, with these rules, I can still connect to port 21 without my subnet list. I want to block ALL subnets and just open those inside the US.

    Read the article

  • How to get Virtual PC to recognize MIDI devices?

    - by bparker
    Hey all. I have an XP Pro virtual machine running inside Virtual PC 2007. My host machine is x64 Windows 7. I have a MIDI keyboard hooked up to my machine via a Turtle Beach USB to MIDI 1x1 cable. I have installed the driver and software on my host machine and ran a soundcheck, and everything appears to be working fine. Playback is sent to the MIDI device with no problems. However, when I attempt to install the driver and run a soundcheck in my XP virtual machine, the device is not found. Other USB devices (mouse, keyboard, flash drives) work fine in the virtual machine, but not they MIDI keyboard. I'm not sure what steps to take in order to troubleshoot the and get the VM to start recognizing the MIDI keyboard. Any help or suggestions would be greatly appreciated. Thanks.

    Read the article

  • Are FC and SAS DAS devices standard enough?

    - by user222182
    Before I ask my questions, here is some background info that may or may not be useful: For the first time I find myself needing a DAS solution. My priority is data through-put in a single direction. I can write large blocks, and I don't need to read at the same time. The server (the data producing device) is not really a typical server, its a very powerful single board computer. As such I have limited options when it comes to the add-in cards I can install since it must use the fairly uncommon interface, XMC. Currently I believe I am limited PCIex8 gen 1 which means that the likely bottle neck for me will be this 16gbps connection. XMC Boards I have found so far offer the following connections: a) Dual 10GBE ethernet controller, total throughput 20gbps b) Dual Quad SAS 2.0 Connectors (SFF-8XXX) HBA (no raid), total throughput 48 gbps c) Dual FC 8gb HBA (no raid), total throughput 16gbps My questions for you guys are: 1) Are SAS and/or FC, and by extension their HBAs, standard enough that I could purchase a Dell or Aberdeen storage server with a raid controller that has external SAS or FC ports and expect that I can connect it to my SAS or FC HBA, be presented with a single volume (if I so configured the storage server), all without having to check for HBA compatibility? 2) On a device like a Dell PowerVault (either DAS or NAS) is there an OS on it to concern myself with, or is it meant to be remotely managed? Is there a local interface in case I cant remotely manage it (i.e. if my single board computer uses an OS not supported by Dell OpenManage). Would this be true of nearly any device which calls itself a DAS? 3) If I purchase some sort of Supermicro storage chassis, installed a raid controller with external connections, is there a nice lightweight OS I can run just for management of the controller? Would I even need an OS since the raid card would be configured pre-boot anyway? 4) It is much easier to buy XMC based 10gigabit ethernet cards (generally dual port). In what ways would I be getting into trouble by using iSCSI as a DAS are direct cabling with SFP+ cables? Thanks in advance

    Read the article

  • C++ Style Comments for Microsoft Word 2008?

    - by user33559
    Hello, I would like to be able use some sort of C++ style commenting for Microsoft Word. E.g. If I have // line of text the entire line should be a comment and should appear in a different colour. Same goes for: /* text block */ I would want text block to be in a different colour than my main text. Another feature that would be nice but not necessary for me to have is some sort of a way to quickly strip all the comments. I have no idea how this could be done, if possible. Any ideas? Thanks.

    Read the article

  • Does IP helper forward subnet broadcasts?

    - by Eamon
    Hi, I have a device on a VLAN that uses UDP subnet broadcasts to advertise its presence to similar devices. This works fine on a single VLAN, but now I need to allow it to communicate with similar devices on a second VLAN. I thought of using the IP helper command in the router, but I am wondering if that only forwards global broadcasts (255.255.255.255)? My device sends out a subnet broadcast (e.g. 192.168.6.255) Will IP helper change the destination address to the target subnet (e.g. 192.168.7.255)? Eamon

    Read the article

  • How to install audio drivers for Acer Revo nettop?

    - by CT
    I have a Acer Revo nettop. I wiped the XP Home install that came on the machine and put XP Pro on. Acer's support website would lead you to believe that this product does not exist. I know it has a NVIDIA ION LE chipset so I headed over to nvidia.com to download drivers. Ive downloaded and installed the Chipset drivers, Graphics Drivers, and HDMI audio drivers. I have no sound. Under Device Manager there is an unknown Audio Device on High Definition Audio Bus. I do not have an HDMI cable to test hdmi audio. I would just like the standard audio mini-jack output to work. Anyone know of the correct driver or a generic driver that would work? Thanks

    Read the article

  • Can someone explain the "use-cases" for the default munin graphs?

    - by exhuma
    When installing munin, it activates a default set of plugins (at least on ubuntu). Alternatively, you can simply run munin-node-configure to figure out which plugins are supported on your system. Most of these plugins plot straight-forward data. My question is not to explain the nature of the data (well... maybe for some) but what is it that you look for in these graphs? It is easy to install munin and see fancy graphs. But having the graphs and not being able to "read" them renders them totally useless. I am going to list standard plugins which are enabled by default on my system. So it's going to be a long list. For completeness, I am also going to list plugins which I think to understand and give a short explanation as to what I think it's used for. Pleas correct if I am wrong with any of them. So let me split this questions in three parts: Plugins where I don't even understand the data Plugins where I understand the data but don't know what I should look out for Plugins which I think to understand Plugins where I don't even understand the data These may contain questions that are not necessarily aimed at munin alone. Not understanding the data usually mean a gap in fundamental knowledge on operating systems/hardware.... ;) Feel free to respond with a "giyf" answer. These are plugins where I can only guess what's going on... I hardly want to look at these "guessing"... Disk IOs per device (IOs/second)What's an IO. I know it stands for input/output. But that's as far as it goes. Disk latency per device (Average IO wait)Not a clue what an "IO wait" is... IO Service TimeThis one is a huge mess, and it's near impossible to see something in the graph at all. Plugins where I understand the data but don't know what I should look out for IOStat (blocks/second read/written)I assume, the thing to look out for in here are spikes? Which would mean that the device is in heavy use? Available entropy (bytes)I assume that this is important for random number generation? Why would I graph this? So far the value has always been near constant. VMStat (running/I/O sleep processes)What's the difference between this one and the "processes" graph? Both show running/sleeping processes, whereas the "Processes" graph seems to have more details. Disk throughput per device (bytes/second read/written) What's thedifference between this one and the "IOStat" graph? inode table usageWhat should I look for in this graph? Plugins which I think to understand I'll be guessing some things here... correct me if I am wrong. Disk usage in percent (percent)How much disk space is used/remaining. As this is approaching 100%, you should consider cleaning up or extend the partition. This is extremely important for the root partition. Firewall Throughput (packets/second)The number of packets passing through the firewall. If this is spiking for a longer period of time, it could be a sign of a DOS attack (or we are simply recieving a large file). It can also give you an idea about your firewall performance. If it's levelling out and you need more "power" you should consider load balancing. If it's levelling out and see a correlation with your CPU load, it could also mean that your hardware is not fast enough. Correlations with disk usage could point to excessive LOG targets in you FW config. eth0 errors (packets in/out)Network errors. If this value is increasing, it could be a sign of faulty hardware. eth0 traffic (bits/second in/out)Raw network traffic. This should correlate with Firewall throughput. number of threadsAn ever-increasing value might point to a process not properly closing threads. Investigate! processesBreakdown of active processes (including sleeping). A quick spike in here might point to a fork-bomb. A slowly, but ever-increasing value might point to an application spawning sub-processes but not properly closing them. Investigate using ps faux. process priorityThis shows the distribution of process priorities. Having only high-priority processes is not of much use. Consider de-prioritizing some. cpu usageFairly straight-forward. If this is spiking, you may have an attack going on, or a process is hogging the CPU. Idf it's slowly increasing and approaching max in normal operations, you should consider upgrading your hardware (or load-balancing). file table usageNumber of actively open files. If this is reaching max, you may have a process opening, but not properly releasing files. load averageShows an summarized value for the system load. Should correlate with CPU usage. Increasing values can come from a number of sources. Look for correlations with other graphs. memory usageA graphical representation of you memory. As long as you have a lot of unused+cache+buffers you are fine. swap in/outShows the activity on your swap partition. This should always be 0. If you see activity on this, you should add more memory to your machine!

    Read the article

  • What solutions do I have to enforce memory limit on PHP server?

    - by Zulgrib
    I would like to enforce memory limit on a folder basis (and have it applied on subfolders) but I don't want the user able to change the memory limit. I know I can disable ini_set and I know I can enforce a hard limit or deny ini_set with Suhosin. With the first one, I doubt it will block changing it from the user.ini file, for the second, the user may still be able to change it to the hard limit I enforce with Suhosin. In both cases, I would prefer to not entierly block ini_set because it may have a legit use for other settings. In case it is important, I'm using PHP version 5.4.4 with nginx (PHP in FPM mode)

    Read the article

  • SQL Server: Is it possible to prevent SQL Agent from failing a step on error?

    - by franklinkj
    I have a stored procedure that runs custom backups for around 60 SQL servers (mixes 2000 through 2008R2). Occasionally, due to issues outside of my control (backup device inaccessible, network error, etc.) an individual backup on one or two databases will fail. This causes this entire step to fail, which means any subsequent backup commands are not executed and half of the databases on a given server may not be backed up. On the 2005+ boxes I am using TRY/CATCH blocks to manage these problems and continue backing up the remaining databases. On a 2000 server however, for example, I have no way to prevent this error from failing the entire step: Msg 3201, Level 16, State 1, Line 1 Cannot open backup device 'db-diff(\PATH\DB-DIFF-03-16-2010.DIF)'. Operating system error 5(Access is denied.). Msg 3013, Level 16, State 1, Line 1 BACKUP DATABASE is terminating abnormally. I am simply asking if anything like this is possible in SQL 2000 or if I need to go in a completely different direction.

    Read the article

  • squidGuard hangs during setup

    - by richard
    I have a squid proxy on my Debian-Gnu-Linux-laptop configured to block some web sites. I can set a browser to use this proxy, but I can also configure it to not use it. As I an using it to block some sites. I do not wish and application to be able to bypass the proxy. Is it possible to to configure a fire wall to black outgoing traffic except if sent by the proxy application or user? I would like a simple configurator if possible.

    Read the article

  • Can SATA be used to connect computers?

    - by André
    Can SATA be used to connect two computers together, just like a crossover Ethernet cable would do ? I know SATA has no "networking" features and even though a controller may have multiple ports, the drives don't "see" each other, and that in SATA one device acts as the host (the computer) and the other device is some kind of "client" (the storage drive). But still, did anyone attempt to make a kernel module that would make one computer appear as a "client" (so that the host's SATA controller detects it as a standard hard drive) and then set up like a pseudo-Ethernet link or a very high speed serial link (and then run pppd on it and do networking) ? Note : I know this is an unprofessional and totally stupid idea, I'm just asking out of curiosity.

    Read the article

  • DVD-ROM disappeared under Windows-7

    - by hometoast
    Windows-7 (build 7100) has forgotten about and refused to recognize that I have an optical drive attached. Linux LiveCD sees it (sees it and it boots from it), so it's isolated to the Windows installation. I do have VirtualCloneDrive installed. But I know I had access to the optical drive after the installation of that. Only recently did I try to rip an iso image for mounting in a VM. I do not see the device under device manager (Start,Run,"devmgmt.msc"). I really do not want to do a fresh install. What are my next steps?

    Read the article

  • Bridging Network Devices with Multiple IPs

    - by Andy
    I have a small server with a single NIC that I am trying to get a bridge functioning on so that I can run KVM. On this NIC I have a couple IPs statically assigned to it: eth0 = 192.168.1.1 eth0:1 = 192.168.1.2 eth0:2 = 192.168.1.3 eth0:3 -> Assign the bridge to this I am attempting to set up a bridge using the following instructions: sudo brctl addbr br0 sudo brctl addif br0 eth0:3 sudo ifconfig br0 192.168.1.120 netmask 255.255.255.0 up sudo route add -net 192.168.1.0 netmask 255.255.255.0 br0 sudo route add default gw 192.168.1.1 br0 sudo tunctl -b -u root -t tap0 > /dev/null sudo ifconfig tap0 up sudo brctl addif br0 tap0 However, when I do the second command: sudo brctl addif br0 eth0:3 It puts the ENTIRE eth0 device into promiscuous mode. This knocks the server offline and inaccessible by anything other than locally. Is there a way to bridge JUST eth0:3 to br0 and not put the entire device into promiscuous mode?

    Read the article

  • renaming hard drives (sdc to sdb) on the fly

    - by w00t
    ata2: link is slow to respond, please be patient (ready=0) kernel: [2761026.198796] ata2: soft resetting link kernel: [2761031.226669] ata2.00: disabled kernel: [2761031.226720] ata2: EH complete kernel: [2761031.226753] sd 1:0:0:0: [sdb] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK,SUGGEST_OK After receiving the error above, I couldn't access /dev/sdb anymore. Not wanting to restart the server, I rescanned for the device using echo "- - -" > /sys/class/scsi_host/host1/scan and it readded the drive as /dev/sdc. From what I have found, I need to use echo "scsi add-single-device 0 0 3 0" > /proc/scsi/scsi, "3" being the SCSI ID which corresponds to sdb. Everything nice up to the point I execute the command and get -bash: echo: write error: Invalid argument. All the solutions point to using this method, but I am unable to. Any other method available? Debian 5.0.8 - 2.6.26-1-686

    Read the article

  • GeForce 8800GT not even giving basic output

    - by Sam
    My Dad bought a GeForce 8800GT graphics card quite a long time ago now. It has never worked in his PC. Print out from a dxdiag: System Information Time of this report: 4/13/2010, 19:52:40 Machine name: USER-PC Operating System: Windows Vista™ Home Premium (6.0, Build 6001) Service Pack 1 (6001.vistasp1_gdr.091208-0542) Language: English (Regional Setting: English) System Manufacturer: To Be Filled By O.E.M. System Model: To Be Filled By O.E.M. BIOS: Default System BIOS Processor: Intel(R) Core(TM)2 Quad CPU Q6600 @ 2.40GHz (4 CPUs), ~2.3GHz Memory: 2046MB RAM Page File: 1045MB used, 3296MB available Windows Dir: C:\Windows DirectX Version: DirectX 10 DX Setup Parameters: Not found DxDiag Version: 6.00.6001.18000 32bit Unicode DxDiag Notes Display Tab 1: No problems found. Sound Tab 1: No problems found. Sound Tab 2: No problems found. Sound Tab 3: No problems found. Input Tab: No problems found. DirectX Debug Levels Direct3D: 0/4 (retail) DirectDraw: 0/4 (retail) DirectInput: 0/5 (retail) DirectMusic: 0/5 (retail) DirectPlay: 0/9 (retail) DirectSound: 0/5 (retail) DirectShow: 0/6 (retail) Display Devices Card name: ATI Radeon HD 2400 PRO Manufacturer: ATI Technologies Inc. Chip type: ATI Radeon Graphics Processor (0x94C3) DAC type: Internal DAC(400MHz) Device Key: Enum\PCI\VEN_1002&DEV_94C3&SUBSYS_00000000&REV_00 Display Memory: 1012 MB Dedicated Memory: 245 MB Shared Memory: 767 MB Current Mode: 1280 x 960 (32 bit) (75Hz) Monitor: Generic PnP Monitor Driver Name: atiumdag.dll,atiumdva.dat,atitmmxx.dll Driver Version: 7.14.0010.0523 (English) DDI Version: 10 Driver Attributes: Final Retail Driver Date/Size: 8/22/2007 02:43:14, 3021312 bytes That info is from the current card that is installed in it and has been installed since its purchase roughly 3-4 years ago. When I physically install the card I put it into a purple slot on the motherboard that the old card was in (if I go into the device manager and select properties on the current card it confirms that the slot is a "PCI Slot 16 (PCI bus 2, device 0, function 0)") and boot up the computer but get absolutely no output. The screen that we have registers that it is connected to something (by not displaying the screen it does when the cable is unplugged) but just remains blank, no output at all. I recently took the card to my University and one of my friends who is better with hardware issues than I am tried it in his system and it worked perfectly. No issues whatsoever. I do not have a spec list for his system but I could get one if you need it. If you need any more information on this issue I will be happy to supply you with it as I am starting to get very annoyed with this problem ^_^

    Read the article

  • How to copy directories using debugfs?

    - by STM
    The debugfs manpage gives the impression that the command 'rdump . .' will recursively copy all files found on the specified filesystem from the debugfs cwd to the native filesystem's cwd. Instead I seem to receive a syntax error, and no copy is initiated? These are the commands I run: cd /path/to/transfer/destination debugfs /dev/sda1 -R rdump . . My task is to copy the entire contents of a clean yet unmountable USB storage device to its host machine's HD. The host machine does not support the inode size used by the USB device's filesystem (256) and its software is not upgradeable, so my intention was to use debugfs to transfer the files. If anyone has any other suggestions for this task I'd be grateful.

    Read the article

  • How can I disable the automatic switch to "library" mode in Windows 7's Media Player 12?

    - by matthews
    Whenever I plug any USB device into my computer while running Windows Media Player 12 in Windows 7, it will automatically swtich the player from the Now Playing mode to Library mode. This is intended to faciliate syncing between Media Player and MP3 players, but it happens for any USB device. I'd like this to not happen since it's infuriating to see this take place while I'm watching something on a separate screen in Media Player just from plugging in a USB key. This has nothing to do with Windows autorun, and nothing to do with versions of Windows pre-7. And no, switching to some other video player is not an option; I've tried them all, none are as good as stock Media Player in 7.

    Read the article

  • Old PCI Video Card and PCI-Express ATI Radeon HD 4200 Pro Living Together

    - by Adam Driscoll
    I have two video cards installed in a Dell Optiplex 745. The PCI card is from 2001 and I was hoping to be able to install it, allowing me to have 3 monitors. The Radeon is already running two itself. The problem is that when I boot the box with default BIOS settings the PCI card displays video to the single display but not the other two. In device manager I can see that both video cards are visible with drivers loaded correctly but underneath monitors I only have a single Generic PnP monitor from the VGA connection to the PCI card. If I switch the BIOS setting to force PCI-E I get the Radeon to display to the two other monitors. When I check device manager with this configuration I see that the PCI card displays an error saying the driver could not be started. Any ideas?

    Read the article

  • Flash player, HD videos and games are choppy

    - by Aimad Majdou
    I have a problem with flash player. HD videos from Youtube or Vimeo and flash games do not play smoothly. I'm using Flash player 11, Windows 7 Sp1, and my graphic card is Intel GMA 4500. Device Manager shows me that all drivers are installed on my computer, so i don't have any problems with drivers. When I run Google chrome, Resource Monitor shows me 15% ~ 40 % of CPU Usage and 40% used Physical Memory, but when I watch a video on Youtube or play a Flash game, the Resource Monitor shows 70% - 90% CPU Usage. Also, when I run some HD Video (Frame width : 1920, Frame height : 1080) on my computer, Device Manager shows me 80% ~ 100% of CPU Usage. before I Reinstall Windows 7, HD Videos and flash games were play smoothly I hadn't any problem with them !! I hope all these informations are enough to answer my question.

    Read the article

  • How to add a new entry to fstab?

    - by Roei
    I mount a device mount /dev/xvdf /mnt/mongo and verify the mount using df-h: Filesystem Size Used Avail Use% Mounted on /dev/xvda1 7.9G 955M 6.9G 12% / tmpfs 299M 44K 299M 1% /dev/shm /dev/xvdf 20G 589M 19G 4% /mnt/mongo But now I'm trying to figure out how to make it auto mount on boot. I understand I need to add a new entry to /etc/fstab, so I perform: $ sed -i '$ a\/dev/xvdf /mnt/mongo xfs defaults 1 1' /etc/fstab But, after reboot, it seems that the auto mount didn't work. The device didn't appear in the df -h list. Should I not use the sed to add the entry? Is the entry I entered incorrect?

    Read the article

  • Cisco ASA 5505 and slow download speeds for Apple devices

    - by James
    For traffic routing through my ASA 5505, downloads for all Apple devices, including AppleTV iPad gen 1 IMac MacBook Pro are very slow. speedof.me show less than 1 Mbps download (where I should have 20 Mbps +), yet for any Windows-based device, the download speeds are in excess of 20 Mbps. The Windows device, including the iMac and MacBook Pro machines, are connected via ethernet cable. Why are Apple devices experiencing such pain? Is it an ASA setting, or something else? Thanks.

    Read the article

  • Understanding packet flows over RVI

    - by choco-loo
    I'm trying to get a full grasp of firewall filters and how to apply them on a Juniper EX4200 switch - to be able to block ports, police traffic and shape traffic. The network architecture is as follows internet >-< vlan4000 >-< vlan43 vlan4000 is a public "routed" block (where all the IPs are routed to and the internet gw is) vlan43 is a vlan with public IPs with devices (servers) attached There are static routes and RVI's on the EX4200 to send all traffic via vlan4000's gateway to reach the internet. I've set up filters on both input and output of the respective RVI's and VLAN's - with simple counters, to measure traffic flow from a server inside of vlan43 and a server on the internet. Using a combination of iperf for UDP and TCP tests and fping for ICMP tests - I observed the following, icmp vlan43>internet internet>vlan43 unit4000-counter-in 0 0 unit4000-counter-out 0 0 unit43-counter-in 100 100 unit43-counter-out 0 0 vlan4000-counter-in 6 4 vlan4000-counter-out 107 104 vlan43-counter-in 101 100 vlan43-counter-out 100 100 tcp vlan43>internet internet>vlan43 unit4000-counter-in 0 0 unit4000-counter-out 0 0 unit43-counter-in 73535 38480 unit43-counter-out 0 0 vlan4000-counter-in 7 8 vlan4000-counter-out 73543 38489 vlan43-counter-in 73535 38481 vlan43-counter-out 38938 75880 udp vlan43>internet internet>vlan43 unit4000-counter-in 0 0 unit4000-counter-out 0 0 unit43-counter-in 81410 1 unit43-counter-out 0 0 vlan4000-counter-in 18 7 vlan4000-counter-out 81429 8 vlan43-counter-in 81411 1 vlan43-counter-out 1 85472 My key goals are to set up a few filters and policers, as there will be many more VLANs - that all need protecting from each other and the internet. Then globally limit/police all outbound traffic to the internet Block inbound ports to vlan43 (eg. 22) Limit outbound traffic from vlan43 (to the internet) Limit outbound traffic from vlan43 (to other vlans) Limit outbound traffic from vlan4000 (to the internet from all vlans) Route traffic from vlans via specific routing instances (FBF) The question What I want to understand is why there isn't ever any activity on unit4000 or vlan4000 inbound or outbound counter - is this because there isn't a device on this VLAN - and that the traffic is only traversing it? And with regards to the TCP test - why is there twice as many packets on unit43-counter-in, vlan4000-counter-out and vlan43-counter-in - is this counting both the inbound and outbound traffic?

    Read the article

< Previous Page | 209 210 211 212 213 214 215 216 217 218 219 220  | Next Page >