Search Results

Search found 16748 results on 670 pages for 'port block'.

Page 210/670 | < Previous Page | 206 207 208 209 210 211 212 213 214 215 216 217  | Next Page >

  • Does a USB to RJ-45 console cable exist?

    - by Carl Flippin
    I am aware of the RJ-45 to DB9 adapter commonly used on cisco routers to access console. I am aware of the USB to DB9 adapters to allow laptops without serial to get a serial port. I am looking for a USB to RJ-45 adapter so I don't have to chain two adapters together. I have searched everywhere but even the pre-packaged solutions seem to have the two adapters chained together. Does such a thing exist? If it doesn't is there some technical reason it cannot? It seems like a manufacturer would just have to wire the DB9 end of the USB adapter differently and it would work just fine plugged straight into the console port of the router.

    Read the article

  • PSAD Firewall/ UDP flood?

    - by Asad Moeen
    Well I'm actually trying to block a UDP Flood on the Application port because the string "getstatus" is causing my application to make large output due to a small input to the attacker's IP. I installed PSAD firewall to do the job. psad -S shows 3000,000 logged packets at the application port and top ports in Scan but does not block the IP of the attacker however other IP Addresses with small number of connections are dropped. I'm thinking that since output is also being made to the attacker, this is why its not getting blocked because iptables rate-limiting is also exactly doing the same thing and not blocking the IP where outgoing connection is also made. Any guesses why it won't work?

    Read the article

  • memcached and IIS manager with windows 2008

    - by user64484
    I have memcached (c:\memcached) running on port 11211 and I have a problem configuring IIS manager I created a site in IIS manager binded to port 11211 and if I have memcached running and try and start the site it says "the process cant access the file because it is being used by another process" If I stop memcached and start the site in IIS (and enable directory browsing) I can access the directory structure http://localhost:11211 ok, if I then try and start memcached it errors with error 1053 "could not start the memcached server on local computer" I know I'm doing something fundamentally wrong here! just cannot figure out how I can use IIS and memcached together. [edit]I should add that I need other servers to be able to access memcached[/edit]

    Read the article

  • Good maintained privacy Add-On/settings set that takes usability into account?

    - by Foo Bar
    For some weeks I've been trying to find a good set of Firefox Addons that give me a good portion of privacy/security without losing to much of usability. But I can't seem to find a nice combination of add-ons/settings that I'm happy with. Here's what I tried, together with the pros and cons that I discovered: HTTPS Everywhere: Has only pro's: just install and be happy (no interaction needed), loads known pages SLL-encrypted, is updated fairly often NoScript - Fine, but needs a lot of fine-tuning, often maintained, mainly blocks all non-HTML/CSS Content, but the author sometimes seems to do "untrustworthy" decission RequestPolicy - seems dead (last activity 6 months ago, has some annoying bugs, official support mail address is dead), but the purpose of this is really great: gives you full control over cross-site requests: blocks by default, let's you add sites to a whitelist, once this is done it works interaction-less in the background AdBlock Edge: blocks specific cross-site requests from a pre-defined whitelist (can never be fully sure, need to trust others) Disconnect: like AdBlock Edge, just looking different, has no interaction possibilities (can never be fully sure, need to trust others, can not interact even if I wanted to) Firefox own Cookie Managment (block by default, whitelist specific sites), after building own whitelist it does it's work in the background and I have full control All These addons together basically block everything unsecure. But there are a lot of redundancies: NoScript has a mixed-content blocker, but FF has it's own for a while now. Also the Cookie blocker from NoScript is reduntant to my FF-Cookie setting. NoScript also has an XSS-blocker, which is redundant to RequestPolicy. Disconnect and AdBlock are extremly redundant, but not fully. And there are some bugs (especially RequestPolicy). And RequestPolicy seems to be dead. All in all, this list is great but has these heavy drawbacks. My favourite set would be "NoScript Light" (only script blocking, without all the additonal redundant-to-other-addons hick-hack it does) + HTTPS Everywhere + RequestPolicy-clone (maintained, less buggy), because RequestPolicy makes all other "site-blockers" obsolete (because it blocks everything by default and let's me create a whitelist). But since RequestPolicy is buggy and seems to be dead I have to fallback to AdBlock Edge and Disconnect, which don't block all and and need more maintaining (whitelist updates, trust-check). Are there addons that fulfill my wishes?

    Read the article

  • Blocking ports on the public IP assigned to lo interface in GNU/Linux

    - by nixnotwin
    I have setup my Ubuntu server as a router and webserver by following the answer given here. My ISP facing interface eth0 has a private 172.16.x.x/30 ip and my lo interface has a public IP as mentioned in the answer to the question linked above. The setup is working well. The only snag I have experienced is that I could not find a way to block the ports exposed by the public IP on the lo interface. I tried doing iptables -A INPUT -i eth0 -j DROP, and my server lost connectivity to the public network (internet). I could not ping any public ips. What I want is a way to block ports that are exposed by the public ip on the lo interface. And also I require iptables rules that can expose ports like 80 or openvpn port to the public network.

    Read the article

  • Microsoft Forefront Management Gateway 2010 - Which topology to choose for monitoring only server?

    - by MadBoy
    Hello, I've installed Forefront and wanted to use it as monitoring traffic solution until we decide to put it as a router. I've 2 nic's assigned to this virtual machine. One NIC has connected port which is "mirror port" of our WAN redirected on switch so it sees all the network traffic flying by. The other NIC is internet access. This server is located inside our lan network. What topology should i choose and which options I should look at to be able to see which traffic is used (SMTP, WWW etc) and who does what? We had cases of infected machines with spam and we want to be able to see that some machine is sending large amounts of mails. Is that possible ?

    Read the article

  • GF 3.0.1 + Virtual Server: www.myhost.com:8080/projectname-war => www.myhost.com. How?

    - by Harry Pham
    I need to change www.myhost.com:8080/myproject-war to www.myhost.com. This is what I try. In admin console in Glassfish 3.0.1, I create a http-listener-3 with port 9090 and address 0.0.0.0 (I want to have port 80, but got access-denied or some sort). I then create a virtual server call scholar, with Id=scholar, Hosts=${com.sun.aas.hostName}, Network Listeners: http-listener-3, Default Web Module=project#project-war.war(it is the only option from the drop down list since I only deploy 1 app). Then under Applications, I set the virtual server of the application to be scholar. Save and restart. I try localhost:9090, and expecting that it will load my project like as if I type localhost:9090/project-war. But it does not. I already set the Default Web Module, to be the project, why doesnt it load the project by default?

    Read the article

  • Connecting to local Sql server 2005 through Internet

    - by Manish
    Hello My Sql server is on Local Machine, I want to access it through Internet. I Configure Surace manager and Configuration manager of sqlserver 2005 for remote access. My sqlserver is running on port:1433 I am using port forwarding , I can access service of other ports, My Connetion String Is: Data Source=190.190.200.100,1433;Network Library=DBMSSOCN;Initial Catalog=myDataBase;User ID=myUsername;Password=myPassword; But it gives following error when i am trying to connect sql server through internet: A network-related or instance-specific error occurred while establishing a connection to SQL Server. The server was not found or was not accessible. Verify that the instance name is correct and that SQL Server is configured to allow remote connections. (provider: TCP Provider, error: 0 - A connection attempt failed because the connected party did not properly respond after a period of time, or established connection failed because connected host has failed to respond.)

    Read the article

  • cannot connect to MS FTP 7.5 on Windows 2008 on Amazon EC2 instance

    - by minerj
    I have just installed the MS FTP 7.5 upgrade on my Windows 2008 Server (Service Pack 2) running on an Amazon EC2 instance. In the FTP Firewall Support settings for the server in IIS Manager I have set up the passive port range 45001 - 45005 and also set the External Firewall IP address to match the assigned Amazon Elastic IP address. Using the AWS Console I changed the Security Group for the server to allow access to the server through ports 21 and 45001 through 45005. Using an FTP client (either the command line FTP client or Windows Explorer) on the Amazon server I can connect to the FTP server but I cannot connect with an external FTP client. When I checked to see which ports were open on the server using Shields Up it shows that port 21 is open but ports 45001 to 45005 are closed. I assume I'm missing something. Any help greatly appreciated.

    Read the article

  • Apache ProxyPass ignore static files

    - by virtualeyes
    Having an issue with Apache front server connecting to a Jetty application server. I thought that ProxyPass ! in a location block was supposed to NOT pass on processing to the application server, but for some reason that is not happening in my case, Jetty shows a 404 on the missing statics (js, css, etc.) Here's my Apache (v 2.4, BTW) virtual host block: DocumentRoot /path/to/foo ServerName foo.com ServerAdmin [email protected] RewriteEngine On <Directory /path/to/foo> AllowOverride None Require all granted </Directory> ProxyRequests Off ProxyVia Off ProxyPreserveHost On <Proxy *> AddDefaultCharset off Order deny,allow Allow from all </Proxy> # don't pass through requests for statics (image,js,css, etc.) <Location /static/> ProxyPass ! </Location> <Location /> ProxyPass http://localhost:8081/ ProxyPassReverse http://localhost:8081/ SetEnv proxy-sendchunks 1 </Location>

    Read the article

  • Host not visible in ECC after pushing master agent on server

    - by wildchild
    Hi all!! ECC master Agent has been pushed to one of the servers.. Once a Master Agent installed the host should appear within ECC.However, I am unable to see the host. I asked the Server team to stop and start the master agent ,and to check whether required port is enabled, so that server can talk with ECC server. After restarting the service I get an error.I even checked if the port is used by any other service ,it is not.. Somebody plz help what should done here..it’s a Windows server. Here's the error:- "The EMC control Center Master agent service on local computer atrted and the stopped.Some services stopped automatically if they 've no work to do,for example prformance logs and alert services" Thanks in advance!!

    Read the article

  • Scientific Linux - mysql and apache fail to start on reboot

    - by Derek Deed
    Both mysqld and httpd fail to restart following a reboot of the server, although chkconfig --list shows both daemons set to on for run levels 2,3,4 & 5 All control is being exectuted via Webmin Reboot server – MySQl and Apache not running MySQL Database Server MySQL version 5.1.69 MySQL is not running on your system - database list could not be retrieved. ________________________________________ Click this button to start the MySQL database server on your system with the command /etc/rc.d/init.d/mysqld start. This Webmin module cannot administer the database until it is started. Apache Webserver Apache version 2.2.15 Start Apache Search Docs.. Global configuration Existing virtual hosts Create virtual host Select all. | Invert selection. Default Server Defines the default settings for all other virtual servers, and processes any unhandled requests. Address Any Port Any Server Name Automatic Document Root /var/www/drupal Virtual Server Processes all requests on port 443 not handled by other virtual servers. Address Any Port 443 Server Name Automatic Document Root /var/www/drupal Select all. | Invert selection. chkconfig --list mysqld mysqld 0:off 1:off 2:on 3:on 4:on 5:on 6:off chkconfig --list httpd httpd 0:off 1:off 2:on 3:on 4:on 5:on 6:off Manually Restart Apache chkconfig --list httpd httpd 0:off 1:off 2:on 3:on 4:on 5:on 6:off Manually Restart MySQL chkconfig --list mysqld mysqld 0:off 1:off 2:on 3:on 4:on 5:on 6:off Everything now running okay; but no difference in the chkconfig outputs above. I tried: chkconfig --levels 235 httpd on /etc/init.d/httpd start and the same for mysqld but no change in operation. Log files show that the shutdown has been completed successfully; but there is no indication of the service restarting until it is executed manually: 131112 13:59:15 InnoDB: Starting shutdown... 131112 13:59:16 InnoDB: Shutdown completed; log sequence number 0 881747021 131112 13:59:16 [Note] /usr/libexec/mysqld: Shutdown complete 131112 13:59:16 mysqld_safe mysqld from pid file /var/run/mysqld/mysqld.pid ended 131112 14:09:52 mysqld_safe Starting mysqld daemon with databases from /var/lib/mysql 131112 14:09:52 InnoDB: Initializing buffer pool, size = 8.0M 131112 14:09:52 InnoDB: Completed initialization of buffer pool And the Apache logs: [Tue Nov 12 13:59:13 2013] [notice] suEXEC mechanism enabled (wrapper: /usr/sbin/suexec) [Tue Nov 12 13:59:13 2013] [notice] Digest: generating secret for digest authentication ... [Tue Nov 12 13:59:13 2013] [notice] Digest: done [Tue Nov 12 13:59:14 2013] [notice] Apache/2.2.15 (Unix) DAV/2 PHP/5.3.3 mod_ssl/2.2.15 OpenSSL/1.0.0-fips configured -- resuming normal operations [Tue Nov 12 13:59:14 2013] [notice] caught SIGTERM, shutting down [Tue Nov 12 14:27:13 2013] [notice] suEXEC mechanism enabled (wrapper: /usr/sbin/suexec) [Tue Nov 12 14:27:13 2013] [notice] Digest: generating secret for digest authentication ... [Tue Nov 12 14:27:13 2013] [notice] Digest: done [Tue Nov 12 14:27:13 2013] [notice] Apache/2.2.15 (Unix) DAV/2 PHP/5.3.3 mod_ssl/2.2.15 OpenSSL/1.0.0-fips configured -- resuming normal operations Is anyone able to shed any light on this problem?

    Read the article

  • Laptop charger disconnects and reconnects, charger or battery broken?

    - by Rob
    I've got an Acer Aspire One netbook (AOA-150) and there's obviously something wrong with it. The charging port gets VERY HOT and the charger seems to disconnect and reconnect quickly sometimes. This only happens when the netbook is running, and it doesn't seem to care what it's doing other than being on. The battery has an extremely short life (< 30minutes, sometimes) and I almost exclusively run it on the power cable (which needs the battery plugged in. Having it just plugged into the wall won't start up). Does this sound like a problem with the power cable or the battery? The plug for the cable and the port get so hot that if I held them for longer than a few seconds, I'm sure I'd get burnt. EDIT Just got "Popular Question" on this and it WAS the power jack. The ground on it came loose from the board. A bit of solder on it and everything is working great again.

    Read the article

  • Unexpected network traffic?

    - by robwalker
    My internet connection is via a fixed wireless connection using a 900MHz Motorola Canopy module. The router reports a fairly consistent 32-64Kbps of incoming traffic on the WAN port. When I attached a PC directly to the port and run Wireshark, I get a dump showing a lot of chatter from other machines that I presume are connected to the same tower. This didn't include end-to-end traffic, but was there were a lot of ARP requests, SSDP traffic, ICMP and other network discovery type stuff. Is this 'normal' or does it suggest a misconfiguration somewhere? As far as I can tell there is no need for my modem to be receiving any of this traffic (other than wanting to know what the names of my neighbours machines and printers are!) Since the internet connection is slow at the best of time, having this amount of background noise seems very wasteful.

    Read the article

  • Exchange Server 2010 ActiveSync SSL Certificate Problem

    - by Cell-o
    Hi All, We have a problem related Exchange Server 2010 Activesync.My problem is;When I connecting to activesync from outside, I am receiving the following error. ExRCA is testing Exchange ActiveSync. The Exchange ActiveSync test failed. Test Steps Attempting to resolve the host name mail.xxxxx.com in DNS. The host name resolved successfully. Additional Details IP addresses returned: xx.0.x3.4 Testing TCP port 443 on host mail.x.com to ensure it's listening and open. The port was opened successfully. Testing the SSL certificate to make sure it's valid. The SSL certificate failed one or more certificate validation checks. Test Steps Validating the certificate name. Certificate name validation failed. Tell me more about this issue and how to resolve it Additional Details Host name mail.x.com doesn't match any name found on the server certificate CN=xxxxxx. Thanks in advance all your help.

    Read the article

  • Can't bring NAT to work

    - by user31738
    Hello, I bought a D-link DIR-300 wireless router and i can't bring NAT to work, i have an ssh and http service i need to forward to the internet. My connection is as follows: I have an ADSL connection, i'm using a ADSL ethernet modem connected and working, it doesnt let me put it on bridge mode. I have my router connected to my adsl modem through ethernet, it gets its ip through DHCP (and i'ts always the same) I have a desktop computer running linux with apache and openssh configured and working, it has fixed ip. I configured the NAT in the modem forwarding port 22 from the router ip to the internet. In the router i setup NAT forwarding port 22 from the desktop computer fixed ip to out there. This setup already worked with a fonera i had before, can anyone help me with this or tell me what kind of tests do i need to do? How can i test if the router is forwarding ports correctly before the modem?

    Read the article

  • Proxy Error 502 "Reason: Error reading from remote server" with Apache 2.2.3 (Debian) mod_proxy and Jetty 6.1.18

    - by Martin
    Apache is receiving requests at port :80 and proxying them to Jetty at port :8080 The proxy server received an invalid response from an upstream server The proxy server could not handle the request GET /. My dilemma: Everything works fine normally (fast requests, few seconds or few tens of seconds long requests are processed ok). Problems occur when request processing takes long (few minutes?). If I issue request instead directly to Jetty at port :8080 the request is processed OK. So problem is likely to sit somewhere between Apache and Jetty where I am using mod_proxy. How to solve this? I have already tried some "tricks" related to KeepAlive settings, without luck. Here is my current configuration, any suggestions? #keepalive Off ## I have tried this, does not help #SetEnv force-proxy-request-1.0 1 ## I have tried this, does not help #SetEnv proxy-nokeepalive 1 ## I have tried this, does not help #SetEnv proxy-initial-not-pooled 1 ## I have tried this, does not help KeepAlive 20 ## I have tried this, does not help KeepAliveTimeout 600 ## I have tried this, does not help ProxyTimeout 600 ## I have tried this, does not help NameVirtualHost *:80 <VirtualHost _default_:80> ServerAdmin [email protected] ServerName www.mydomain.fi ServerAlias mydomain.fi mydomain.com mydomain www.mydomain.com ProxyRequests On ProxyVia On <Proxy *> Order deny,allow Allow from all </Proxy> ProxyRequests Off ProxyPass / http://www.mydomain.fi:8080/ retry=1 acquire=3000 timeout=600 ProxyPassReverse / http://www.mydomain.fi:8080/ RewriteEngine On RewriteCond %{SERVER_NAME} !^www\.mydomain\.fi RewriteRule /(.*) http://www.mydomain.fi/$1 [redirect=301L] ErrorLog /var/log/apache2/error.log # Possible values include: debug, info, notice, warn, error, crit, # alert, emerg. LogLevel warn CustomLog /var/log/apache2/access.log combined ServerSignature On </VirtualHost> Here is also the debug log from a failing request: 74.125.43.99 - - [29/Sep/2010:20:15:40 +0300] "GET /?wicket:bookmarkablePage=newWindow:com.mydomain.view.application.reports.SaveReportPage HTTP/1.1" 502 355 "https://www.mydomain.fi/?wicket:interface=:0:2:::" "Mozilla/5.0 (Windows; U; Windows NT 6.1; fi; rv:1.9.2.10) Gecko/20100914 Firefox/3.6.10" [Wed Sep 29 20:20:40 2010] [error] [client 74.125.43.99] proxy: error reading status line from remote server www.mydomain.fi, referer: https://www.mydomain.fi/?wicket:interface=:0:2::: [Wed Sep 29 20:20:40 2010] [error] [client 74.125.43.99] proxy: Error reading from remote server returned by /, referer: https://www.mydomain.fi/?wicket:interface=:0:2:::

    Read the article

  • Suggestions for a SOHO/Home Asterisk system

    - by James
    I would like to buy a small embedded system that runs Linux and Asterisk. I would like two FXS ports ( to plug analogue phones into ) and one FXO port ( to plug in to my real line to allow access to the POTS ). I would like it to have a USB port to hold storage for voicemail. I really want it for home use so I would like it to be under £150 ( say $250 ), given that you can buy ADSL routers for around this much can any of them be made to run Linux and Asterisk? I don't want a PC as the power usage would be too high. I am looking for something like this ASDL router but open and able to run Asterisk or another open PBX. At worst I would like a box which had one FXO and two FXS and just made them completely available over IP to a full Asterisk system on a low power Atom system.

    Read the article

  • how to pass domain name to backend with pound

    - by FurtiveFelon
    I am using pound as a way to decode SSL for the backend, but the bulk of the work is done on varnish (including virtualhost stuff). As a result, I need pound to just forward all other traffic to varnish verbatim, but it doesn't seem to do that. I am using the default configuration: ListenHTTP Address 1.2.3.4 Port 8080 ## allow PUT and DELETE also (by default only GET, POST and HEAD)?: xHTTP 0 Service BackEnd Address 127.0.0.1 Port 80 End End End So whenever I hit example.com:8080, it will always redirect to the default backend for varnish, which i assume was because the domain (host) header isn't send along. Anyone know what could be wrong? Thanks a lot! Jason

    Read the article

  • Parse java console output with awk

    - by Bob Rivers
    Hi, I'm trying to use awk to parse an output generated by a java application, but it isn't working. It seems that the command after the pipe isn't able to get/see the data throwed by the java app. I'm executing the following command (with the return generated by the command): [root@localhost]# java -jar jmxclient.jar usr:pass host:port java.lang:type=Threading ThreadCount 06/11/2010 15:46:37 -0300 org.archive.jmx.Client ThreadCount: 103 What I need it's only the last part of the string. So I'm tryng to use awk (with pipe at the end of the line |awk -F ':' '{print $4}': [root@localhost]# java -jar jmxclient.jar usr:pass host:port java.lang:type=Threading ThreadCount|awk -F ':' '{print $4}' But the output isn't being parsed. It throws the entire string: 06/11/2010 15:46:37 -0300 org.archive.jmx.Client ThreadCount: 103 I also tryed to use |cut -f4 -d":" with the same result: the string isn't parsed. So my question is, how do I parse the output in order to get just the number at the end of the string? TIA, Bob

    Read the article

  • Building boost 1.42 on FreeBSD 6.3

    - by Ivan Perekluyev
    Hi, i need to build mapnik on freebsd 6.3, but port marked as 'broken', so i forced to build it from source. With boost 1.41 (which is in ports) mapnik doesn't build. somewhere in internet, i found that mapnik successfully builded with boost 1.42. So, i download patch from wiki.freebsd.org/BoostPortingProject andd apply it: wget http://alexanderchuranov.com/boost-port/boost-from-1.41-to-1.42-2010-02-16-17-11.diff cd /usr/ports patch -p0 -i ~/boost-from-1.41-to-1.42-2010-02-16-17-11.diff after that, i trying to install boost-all metaport, but its failed. cd devel/boost-all make install 2>&1 | tee build.log tail -n 100 build.log > short_build.log Build.log (attention, 5m !): dl.dropbox.com/u/7365614/build.log Short build log: http://paste.pocoo.org/show/224474/ Thanks!

    Read the article

  • How to close the logon process named NtLmSsp ?

    - by Aristos
    I have a windows 2003 server and time to time I am getting many login failures like this one. Logon Failure: Reason: Unknown user name or bad password User Name: administrator Domain: xx.xx.xx.xx Logon Type: 3 Logon Process: NtLmSsp Authentication Package: NTLM Workstation Name: XLHOST Caller User Name: - Caller Domain: - Caller Logon ID: - Caller Process ID: - Transited Services: - Source Network Address: 173.45.70.100 <- hacker Source Port: 4722 AND Logon attempt by: MICROSOFT_AUTHENTICATION_PACKAGE_V1_0 Logon account: user Source Workstation: XLHOST Error Code: 0xC0000064 The question is, how can I close this process of login ?, what I have left open and some one can try to login ? Some notes: I login to the server using tunneling, nothing is open except dns, email, and web ports, not even ftp, and all default ports are change and hidden. I also monitor port scan and capture any one that try to find the hidden ports. Probably it is something open... Thank you in advanced.

    Read the article

  • Some notebooks can connect to internet via certain wireless router, some can't

    - by Nathaniel
    I take a class in the building of a business and we sometimes use their internet via Wi-Fi. In the last few weeks, though, some notebooks haven't been able to connect to the internet even though they are connected to the router. It affected first a few of us and then all of us. Last week I tweaked around the network settings on the router (yes, the admin password is the same as the network key) and even moved the internet cable on the router from port 1 to the internet port. None of this really worked so I put things more or less back as I found them and alerted someone that someone who knew more than me had better have a look at the router. So, I don't know if anybody has had a look at it but now 2 of us can again connect to the internet. I had a look at the router settings last week and I really couldn't see what might be creating this issue. What might be the problem?

    Read the article

  • Sharing internet connection from Windows XP using wi-fi router

    - by Darius
    Hi, I have an network configuration like: Ethernet cable from ISP connected to Windows XP machine, configured with static IP 192.168.0.3 Another ethernet connection from 2nd Windows XP machine's network adapter to a Wi-Fi router (D-Link Airport G+) XP set to "Share internet connection", the 2nd adapter configured as static to 192.169.0.1 D-Link Airport Wi-Fi router also configured as "static connection", it's IP set to 192.169.0.2, default gateway set to 192.169.0.1. Network mask everywhere is 24. Laptop computer connected with the router with static IP 192.169.0.3 The problems are: XP machine sees the router (it's able to ping it and access it via the web admin tool) The router somehow cannot PING the XP machine (using the tool provided by the web-based admin tool) The laptop computer cannot ping anything and cannot be pinged The router is only accessible when the ethernet cable is connected with a router's 1-4 LAN port, when I connect it via "WAN" port (which I believe is the proper one) it's not visible from the XP machine If you have similar experience with configuring a network like this I would really appreciate your help. I cannot use the Wi-Fi router with the ISP cable itself.

    Read the article

  • Routing and Remote access rule not being applied internally (Windows SBS)

    - by Tim Saunders
    Hi, I have a Microsoft Small Business Server. I have pointed an external domain name to the external fixed IP address for the server. In routing and remote access I have defined a service for our subversion server as follows: Incoming port: 8443 Private address: 192.168.10.5 Outgoing port: 8443 192.168.10.5 is our development server, not the SBS (which is at 192.168.10.1) This rule works correctly if I am not on our internal network. However if I am on the internal network this rule does not get applied. What can I do/set so this rule is applied both internally and externally (so users with laptops et, don't keep having to change the URL by which they access the subversion server) Not sure what other info you may need, so please let me know if more details are required. T

    Read the article

< Previous Page | 206 207 208 209 210 211 212 213 214 215 216 217  | Next Page >