Search Results

Search found 7338 results on 294 pages for 'useful'.

Page 210/294 | < Previous Page | 206 207 208 209 210 211 212 213 214 215 216 217  | Next Page >

• Debian can't connect to internet using LAN

  - by tampe125

  I have a headless Raspberry Pi using Debian Wheezy. I have a wifi dongle and if I connect my Raspberry using it, everything works fine: I can connect to the Internet, I can ping, I can update. However, if I get down my wifi and set up the lan interface, I lost my internet connection. I still can connect to it locally, using my laptop, but the connection doesn't exit (ie ping is not working). Some useful info: cat /etc/network/interfaces auto lo auto eth0 iface eth0 inet static address 192.168.0.105 netmask 255.255.255.0 gateway 192.168.0.1 ping www.google.com (nothing request timed out) ifconfig eth0 Link encap:Ethernet HWaddr b8:27:eb:a2:b5:20 inet addr:192.168.0.105 Bcast:192.168.0.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:1130 errors:0 dropped:0 overruns:0 frame:0 TX packets:1116 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:97223 (94.9 KiB) TX bytes:146140 (142.7 KiB) ping 192.168.0.1 PING 192.168.0.1 (192.168.0.1) 56(84) bytes of data. ^C --- 192.168.0.1 ping statistics --- 19 packets transmitted, 0 received, 100% packet loss, time 18007ms cat /etc/resolv.conf nameserver 8.8.8.8 netstat -r Kernel IP routing table Destination Gateway Genmask Flags MSS Window irtt Iface default 192.168.0.1 0.0.0.0 UG 0 0 0 eth0 192.168.0.0 * 255.255.255.0 U 0 0 0 eth0 well, I think that's all... Any ideas?

  Read the article

• Outlook conversation view and categories

  - by Greg Jackson

  At work, I tend to receive a couple of hundred emails a day. To keep from being overwhelmed, I have been using categories to sort and prioritize my mail messages. I auto-assign categories, then group by them: Code Reviews, To, CC, Distribution List/BCC. This means that, for example, a message that's explicitly to me will always show up higher in my inbox than one I get because I'm on a Distribution List. It's a huge time saver and it brings important emails to my attention much more quickly. Recently, the email threads I'm involved in have started to get quite long, and I'd like to be able to use conversation view, or at least sort by subject. Outlook, however, doesn't seem to support any (useful) combination of conversation view and categories. I've tried the following things without success: Grouping by category, then conversation view -- Outlook gives me an error (the grouping/sort combination is too complex). Using a custom view to group by conversation -- category doesn't show up as an option to sort by Grouping by category, then subject -- Getting closer, but the top subject is the first alphabetically, not the most recent Grouping by conversation, then category -- This works, but it doesn't do me much good, because the top conversation is the latest, without regard to what category it belongs to Is there a way for me to retain my category system or something similar while taking advantage of grouping related emails together? I've written Outlook plugins in the past, so even that's not too out there to serve as a proper solution.

  Read the article

• So who decided VGA cables should be symetrical ? [closed]

  - by mgb

  < rant So who decided that VGA cables should be the same gender connector at both ends? I just spent an hour trying to fix a server that would apparently boot but wouldn't display any post messages - I needed to change some bios settings. The monitor gives me a helpful error message - "unable to display this resolution". Wondering how it can't show simple VGA res, I reset the bios, when that doesn't work I remove the BIOS battery. The system is in a rack with a keyboard and monitor mounted 6ft away - with the cable running through the normal waist thick rats nest of wiring of wiring. The monitor worked with another system, so it and the VGA cable are good, I brought in another monitor and tried that - still nothing. Eventually I ripped the rack apart to discover that the other end of the VGA connector I was trying to plug into the server was actually plugged into another server box ! And the second monitor I was testing was plugged into the first monitor. An error message like - "I'm actualy plugged into another monitor stupid" - would be useful. So would having a connector with a male end and a female end. < end rant - thank you

  Read the article

• Why is Apache htdigest authentication failing in IE10 on Windows 8?

  - by Kevin Fodness

  One of our developers reported that for the past week or two, the htdigest authentication that we have set up on our test sites in Apache is not working in IE10 on Windows 8. It's fine on IE10 on Windows 7, and it's fine on Chrome on Windows 8. The specific behavior is: Navigate to site with htdigest authentication enabled, username and password form pops up, enter correct username and password, and the username and password box pops up again. Potentially useful information: All patches applied on Windows 8 box No additional software on Windows 8 box other than Outlook 2013 and a browser test suite (Chrome, Firefox, Opera, Chrome Canary, Opera Next) Win8 running in a virtual machine on Xen Same behavior can be replicated on Win8/IE10 on Browserstack.com Server running Ubuntu 10.10 with Apache 2.2.16 This feels like a patch was applied to the Windows box that broke digest authentication for IE10 on Win8 (box configured for automatic updates). However, without knowing a specific date I can't necessarily nail this down. Has anyone else experienced this problem? EDIT: This problem only happens in the "Metro" interface, not when running IE10 in desktop mode. As of a few weeks ago, it worked fine even in the "Metro" interface.

  Read the article

• Unable to browse to apache service, Service is running

  - by Jeff

  Summary I have a very peculiar problem. I am not able to open the "It Works!" page after installing a fresh server with apache. I am able to ssh to the box (from outside the network). Apache seems to be running on my Centos6.4x86_64 box just fine. Nothing useful in /var/logs/httpd/*. What am I missing? The setup I am outside the network right now. The "server" is a VM on my home computer running bridged mode. public ip: A.B.C.D Host: 192.168.1.5 VM: 192.168.1.8 I have a verizon fios router that is forwarding ports 22, 80, and 8888 to the VM. I am able to ssh over port 22, but I am not able to browse to the public URL over port 80. so A.B.C.D:22 is working, but http://A.B.C.D:80 is not. What I've tried nmap to see if it is listening: nmap -sT -O localhost Starting Nmap 5.51 ( http://nmap.org ) at 2013-10-25 11:10 EDT Nmap scan report for localhost (127.0.0.1) Host is up (0.000040s latency). Other addresses for localhost (not scanned): 127.0.0.1 Not shown: 996 closed ports PORT STATE SERVICE 22/tcp open ssh 25/tcp open smtp 80/tcp open http 3306/tcp open mysql I tried going to it locally (lynx) and it does work. So, is the problem in my ports?

  Read the article

• NFS Datastore Appears Empty!

  - by daemonchild

  Hi guys, I've got an NFS server problem. The datastore connected and seems to be a valid datastore in both the vSphere client and under /vmfs/volumes. The issue is that it appears to be empty! I can create files (eg: touch /vmfs/volumes/nfs_common/thefile) and it is correctly written to the nfs store. I can verify this by looking on the nfs server itself. But the vmkernel only sees an empty datastore; the file disappears. Another freebsd box can mount the same NFS share and see the files correctly. Some useful data: ESXi 4.0.0 Build 208167 NFS is unfsd running on a Buffalo Linkstation Pro Duo (a bit hacky I know). The share has file system permissions set to 777 at the moment. My /etc/exports is as follows, and as I say it connects fine. /mnt/array1/ESX_Shared 192.168.16.0/255.255.255.0(insecure,rw,sync,no_root_squash,no_subtree_check) The ESXi servers can also successfully mount NFS shares from other NFS servers. Any ideas guys? Thanks, Tom

  Read the article

• How to get an inactive RAID device working again?

  - by Jonik

  After booting, my RAID1 device (/dev/md_d0 *) sometimes goes in some funny state and I cannot mount it. * Originally I created /dev/md0 but it has somehow changed itself into /dev/md_d0. # mount /opt mount: wrong fs type, bad option, bad superblock on /dev/md_d0, missing codepage or helper program, or other error (could this be the IDE device where you in fact use ide-scsi so that sr0 or sda or so is needed?) In some cases useful info is found in syslog - try dmesg | tail or so The RAID device appears to be inactive somehow: # cat /proc/mdstat Personalities : [linear] [multipath] [raid0] [raid1] [raid6] [raid5] [raid4] [raid10] md_d0 : inactive sda4[0](S) 241095104 blocks # mdadm --detail /dev/md_d0 mdadm: md device /dev/md_d0 does not appear to be active. Question is, how to make active the device again (using mdmadm, I presume)? (Other times it's alright (active) after boot, and I can mount it manually without problems. But it still won't mount automatically even though I have it in /etc/fstab: /dev/md_d0 /opt ext4 defaults 0 0 So a bonus question: what should I do to make the RAID device automatically mount at /opt at boot time?) This is an Ubuntu 9.10 workstation. Background info about my RAID setup in this question.

  Read the article

• What are the steps needed to set up and use security for AWS command line tools?

  - by chris

  I've been trying to set up the AWS command-line tools following Eric's most useful guide at http://alestic.com/2012/09/aws-command-line-tools. I can't seem to find a good how-to for how to generate the x509 certificate and private key, and how that relates to the various security files the guide creates. Update: I have found a couple of links that describe the some steps. These steps seem to work, however I'm not sure if this is secure & the best way to do it: 1) Create a private key openssl genrsa -out my-private-key.pem 2048 2) Create x.509 cert openssl req -new -x509 -key my-private-key.pem -out my-x509-cert.pem -days 365 Hit enter to accept all of the defaults. Then, from the IAM Dashboard, User, select a user & click on the "Security Credentials" tab. Click on "Manage Signing Certificates", then "Upload Signing Certificate", paste in the contents of my-x509-cert.pem, click OK and it should be accepted. One step that is discussed, but not required for me, was the addition and subsequent removal of a pass phrase on the private key. Should I have been prompted for one, and is my cert potentially unsafe because of this?

  Read the article

• Sync OneNote Notebooks to/on SkyDrive

  - by Sam

  I've got OneNote running on all computers in our house, using it all the time with several people and computers. The only drawback: I want to keep the copies of OneNote in sync without having to run a dedicated server myself. Right now one of my computers has a folder share, where all others sync to, but this is highly impractical since the computer is not always running. So my question is: is it possible to put the notebook files on a (private) SkyDrive Folder and have all the computers sync to there? This way all computers could keep in sync whenever they got access to the web. Can this be done? and, of course, How? [Update] Maybe I should not have taken knowledge about OneNote as granted: OneNote uses a propietary file format, but has a very good in-file-syncing, working on network shares. Generic 'just sync the complete file' won't be useful at all, because I'd just have 'file has changed on server and on client' conflicts all the time. The sync needs to know OneNote files and be able to sync the content - eg. OneNote itself needs to sync the files, not some generic sync tool.

  Read the article

• HD video editing system with Truecrypt

  - by Rob

  I'm looking to do hi-def video editing and transcoding on an unencrypted standard partition, with Truecrypt on the system partition for sensitive data. I'm aiming to keep certain data private but still have performance where needed. Goals: Maximum, unimpacted, performance possible for hi-def video editing, encryption of video not required Encrypt system partition, using Truecrypt, for web/email privacy, etc. in the event of loss In other words I want to selectively encrypt the hard drive - i.e. make the system partition encrypted but not impact the original maximum performance that would be available to me for hi-def/HD video editing. The thinking is to use an unencrypted partition for the video and set up video applications to point at that. Assuming that they would use that partition only for their workspace and not the encrypted system partition, then I should expect to not get any performance hit. Would I be correct? I guess it might depend on the application, if that app is hard-wired to use the system partition always for temporary storage during editing and transcoding, or if it has to be installed on the C: system partition always. So some real data on how various apps behave in the respect would be useful, e.g. Adobe, Cyberlink, Nero etc. etc. I have a Intel i7 Quad-core (8 threads) 1.6Ghz (up to 2.8Ghz turbo-boost) 4Gb, 7200rpm SATA, nvidia HP laptop. I've read the excellent posting about the general performance impact of truecrypt but the benchmarks weren't specific enough for my needs where I'm dealing with HD-video and using a non-encrypted partition to maintain max performance.

  Read the article

• Synaptics touchpad stops working randomly

  - by Jus12

  I have two laptops. One dell Vostro and other Vaio Z. Both have Synaptics (Yes, I have checked, and the original drivers were from Synaptics as well). On both laptops, the touchpad scrolling stops working at some arbitrary time and nothing seems to solve it except a reboot. Sometimes, it randomly starts working again. I have downloaded all latest drivers from OEM. Interestingly, when I run a program as Administrator, scrolling works in that window only. This problem is very odd. It happens without any reason and I've not been able to find a fix for more than a year. I have seen some unusual suggestions on forums (e.g., to "restore windows to a previous working state") but never any fix that solves this issue properly. I have tried installing latest drivers and I DO NOT want to restore windows to a previous working configuration. OS: Windows 7 64 bit Professional (Sony Vaio Z - VPCZ128GG) Windows 7 32 bit Professional (Dell) Edit: Temporary solution is to uninstall the synaptics driver and let Windows 7 use its default built in one. However, I really prefer the Synaptic driver because it activates the scroll button rather than the mouse wheel (useful in some apps such as MS Photo Editor)

  Read the article

• Change the Powershell $profile directory

  - by Swoogan

  I would like to know how to change my the location my $profile variable points to. PS H:\> $profile H:\WindowsPowerShell\Microsoft.PowerShell_profile.ps1 H:\ is a network share, so when I create my profile file, and load powershell I get the following: Security Warning Run only scripts that you trust. While scripts from the Internet can be useful, this script can potentially harm your computer. Do you want to run H:\WindowsPowerShell\Microsoft.PowerShell_profile.ps1? [D] Do not run [R] Run once [S] Suspend [?] Help (default is "D"): According to Microsoft, the location of the $profile is determined by the %USERPROFILE% environment variable. This is not true: PS H:\> $env:userprofile C:\Users\username For example, I have an XP machine working how I want: PS H:\> $profile C:\Documents and Settings\username\My Documents\WindowsPowerShell\Microsoft.PowerShell_profile.ps1 PS H:\> $env:userprofile C:\Documents and Settings\username PS H:\> $env:homedrive H: PS H:\> $env:homepath \ Here's the same output from the Vista machine where the $profile points to the wrong place: PS H:\> $profile H:\WindowsPowerShell\Microsoft.PowerShell_profile.ps1 PS H:\> $env:userprofile C:\Users\username PS H:\> $env:homedrive H: PS H:\> $env:homepath \ Since $profile isn't actually determined by %USERPROFILE% how do I change it? Clearly anything that involves changing the homedrive or homepath is not the solution I'm looking for.

  Read the article

• How to connect a USB GDI printer to Linux over a D-Link print server?

  - by jpe

  The setup is the following: +------------+ +-----------------+ +---------+ | HP LJ P1005|--USB--| D-Link DPR-1020 |---LAN---| PC Linux| +------------+ +-----------------+ + +---------+ | +------------+ +--| PC Windows | +------------+ HP LJ P1005 is one of those GDI printers that requires the printer driver to do most of the work for it and therefore is a bit "special". D-Link DPR-1020 is a print server with an Ethernet and an USB port that actually supports printing to challenged (read GDI) printers using a utility called PS-Link. What the utility does is basically mirror a USB port over the network to the print server so that the printer driver and the printer both are happy to talk to each other. The PC-s are notebooks that come and go, i.e. are not there all the time. Is there an equivalent of the D-Link PS-Link utility for Linux that could mirror a USB port over the network for a Linux host? And can the solution be used with D-Link DPR-1020? If not then I basically wasted the money buying the print server because the goal was to share a small printer among a couple of users with diverse operating systems in an office. The print server specs say that it supports Linux and LJ P1005, but the Catch 22 appears to be the solution used for GDI printers... It should be noted that it is possible to print from Linux to LJ P1005 directly over USB. This far sharing involved reconnecting the USB cable to appropriate computer to print. Now one of the desks is separated, so the cable does not work. Searching the net did not yield anything useful. Please do not suggest solutions involving a Windows machine (either virtual or not), my question is whether a solution only involving a Linux machine exists.

  Read the article

• First web server questions

  - by Graeme

  Hi there, Just looking for some help/suggestions with this. I require my own server for an upcoming project that will be hosting users websites. I want to build a control panel the user can log into and modify their website which will be stored elsewhere on the server. This all seems easy enough, It's just managing domains and emails that confuse me. What should I look for to manage domain names and point them to the correct website and also what would be the best way to manage email accounts/set up new ones etc. I want to avoid cPanel/WHM if possible, I'm looking to control most things through the control panel I will be building. So any suggestions on this would be useful as well, as I will be wanting to add email accounts through php (Can be done using a shell I assume?). I will also be wanting to measure bandwidth used on the websites contained in each users directory, any suggestions on making this possible? I'm really looking for some suggestions on what software to use to set this up, any advice would be really helpful! Thanks, Graeme

  Read the article

• Authority Information Access local path being ignored

  - by Kevin

  I have a CA set up in Server 2008 R2, and generally it is working, but I can't control the local path/filename it writes its own certificate to for the Authority Information Access publishing. Here's a screen shot of the dialog I'm trying to set this on: From these settings I would expect to get the file: C:\Windows\system32\CertSrv\CertEnroll\DAMNIT.crt But instead I get: C:\Windows\system32\CertSrv\CertEnroll\SERVER.domain.com_My Issuing Authority(1).crt Of course, the actual change shown wouldn't be very useful, but it's illustrative; no matter what path/filename I use, it always lands up in the same place and with the same name. I actually wanted to change the name from <ServerDNSName>_<CaName><CertificateName>.crt to <CaName><CertificateName>.crt, since the latter corresponds to the HTTP URL whereas the former does not. Admittedly, I haven't set up many CAs so perhaps I'm just deluded as to what this dialog is supposed to be setting, but if so this is notoriously bad UI design. (Incidentally, I have a couple other complaints with the same dialog.) What's going on here and is there some way to get the filename pattern I want?

  Read the article

• Colorizing your terminal and shell environment?

  - by Stefan Lasiewski

  I spend most of my time working in Unix environments and using Terminal emulators. I try to use color on the commandline, because color makes the output more useful and intuitive. What are some good ways to add color to my terminal environment? What tricks do you do? What pitfals have you encountered? Unfortunately, support for color is wildly variable depending on terminal type, OS, TERM setting, utility, buggy implementations, etc. Here's what I do currently, after alot of experimentation: I tend to set 'TERM=xterm-color', which is supported on most hosts (but not all). I work on a number of different hosts, different OS versions, etc. I'm trying to keep things simple and generic, if possible. Many OSs set things like 'dircolors' and by default, and I don't want to modify this everywhere. So I try to stick with the defaults. Instead tweak my Terminal's color configuration. Use color for some unix commands (ls, grep, less, vim) and the Bash prompt. These commands seem to the standard "ANSI escape sequences" I've managed to find some settings which are widely supported, and which don't print gobbledygook characters in older environments (even FreeBSD4!) (For the most part). From my .bash_profile ### Color support # The Terminal application typically does 'export TERM=term=color' # Some terminal types will print Black, White & underlined with these settings. OS=`uname -s` case "$OS" in "SunOS" ) # Solaris9 ls doesn't allow color, so use special characters instead. LS_OPTS='-F' ;; "Linux" ) # GNU tools supports colors! See dircolors to customize colors export LS_OPTS='--color=auto' # Color support using 'less -R' alias less='less --RAW-CONTROL-CHARS' alias ls='ls ${LS_OPTS} export GREP_OPTIONS="--color=auto" ;; "Darwin"|"FreeBSD") # Most FreeBSD & Apple Darwin supports colors # LS_OPTS="-G" export CLICOLOR=true alias less='less --RAW-CONTROL-CHARS' export GREP_OPTIONS="--color=auto" ;; esac

  Read the article

• Setting Up My Home Network

  - by Skizz

  I currently have five PCs at home, three running WinXP and two running Ubuntu. They are set up like this: ISP ----- Modem ---- Switch ---- Ubuntu1 -- B&W Printer | |--WinXP1 | |--WinXP2 Wireless |--Colour Printer | |---------Ubuntu2 |---------WinXP3 (laptop) The Ubuntu1 machine is set up as a PDC using Samba and runs fetchmail, procmail, dovecot to get my e-mail and allow me to access the e-mail via imap so I can read the e-mail on any PC. I'd like to set up the network like this: ISP ----- Modem ---- Ubuntu1 ---- Switch ------WinXP1 | | |--WinXP2 B&W Printer Wireless |--Colour Printer | |---------Ubuntu2 |---------WinXP3 (laptop) My questions are: How to configure Ubuntu1 to act as a firewall. How to configure Ubuntu1 to provide a consistant user authentication across the network, at the moment Samba provides roaming profiles for the XP machines but the Ubuntu2 machine has it's own user lists. I'd like to have a single authentication for both XP machines and linux machines so that users added to the server list will propagate to all PCs (i.e. new users can log on using any PC without modifying any of the client PCs). How to configure a linux client (Ubuntu2 above) to access files on the server (Ubuntu1), some of which are in user specific folders, effectively sharing /home/{user} per user (read and write access) and stuff like /home/media/photos with read access for everyone and limited write access. How to configure the XP machines (if it is different from a the Samba method). How to set up e-mail filtering. I'd like to have a whitelist/blacklist system for incoming e-mails for some of the e-mail accounts (mainly, my kids' accounts) with filtered e-mails being put into quaranteen until a sysadmin either adds the sender to a blacklist or whitelist. OK, that's a lot of stuff. For now, I don't want config files*, rather, what services / applications to use and how they interact. For example, LDAP could be used for authentication but what else would be useful to make the administration of the LDAP easier. Once I have a general idea for the overall configuration, I can ask other questions about the specifics. Skizz I have looked around for information, but most answers are usually in the form of abstract config files and lists of packages to install.

  Read the article

• Most scalable way of serving a small set of static HTTP content

  - by Ekevoo

  The story: Hi guys. I'm among the people responsible for serving the results of the most anticipated (by number of people participating) annual entrance exam in my state. As such, when our results are published, the interest is overwhelming. In the past we delegated the responsibility of serving the results to the media, but that spoils a little the officialness of these results. This year we went with a little (long overdue) experiment of using lighttpd instead of Apache as well as other physical network optimizations I wasn't directly involved with. The results were very satisfactory. The server didn't choke even once, nor we saw any of the usual Twitter complaints on unavailability and/or slowness that were previously common. However, because we still delegated the first publication of the results to the media I'm still not 100% sure we can handle the load of actually publishing the results first. The question: Now because these files are like 14MB in total and a true lightweight Linux distribution isn't that big either, I'm thinking: what if next year we run full RAMdrive? Is there any? Is that useful? Is that worth it for a team that uses Debian almost exclusively? Are there other optimizations that I should be focusing on instead?

  Read the article

• When should NTPd broadcast/broadcastclient be used instead of client/server or peer modes?

  - by Luke404

  The NTP deamon if often used in its simplest mode, which is client/server: you specify one or more server directives in your ntp.conf and your clients will use those servers. In addition to that, when you run your own NTP servers, it is good practice to peer them together, so if one of them looses connectivity to its upstream servers, it will get time from its peers. But NTPd can also work with broadcast and/or multicast distribution of time data, with the documentation stating: broadcast and multicast modes are intended for configurations involving one or a few servers and a possibly very large client population The documentation also says elsewhere: It is possible and frequently useful to configure a host as both broadcast client and broadcast server. A number of hosts configured this way and sharing a common broadcast address will automatically organize themselves in an optimum configuration based on stratum and synchronization distance. I can see one obvious administrative benefit: you don't have to manually specify and update your list of NTP servers in the clients ntp.conf, so to me it looks tempting to use broadcast mode even for a small client population (say 5+ clients with 3~4 servers). I expect network traffic to be a little higher with broadcasts instead of client/server associations, but given the usual gigabit ethernet LAN the impact should be negligible unless you have a very very large number of hosts in the same broadcast domain. At the end of the day, when should broadcast mode be used or avoided? Are there pros and cons I haven't seen?

  Read the article

• How to get rid of "Maxback Engine" for good?

  - by Jonik

  I used to have a Maxtor Shared Storage II network drive; it broke down long ago already. (Later I tried to recover some data from it, and partially succeeded, but haven't yet fully documented it on that question.) Anyway, I just noticed there are still some lingering bits remaining of the (thourougly crappy) software that came with the Maxtor device: a background process called "MaxBack Engine". I googled around a bit and found something related but not very useful: http://www.straitmac.com/jforum/posts/list/600.page http://discussions.apple.com/thread.jspa?threadID=725692 Under /Applications I found "Maxtor EasyManage.app" which I used to use for controlling the drive, and showed it some "rm -rf". Before deleting, I noted that the bundle did contain "MaxBack Engine.app" under Content/Resources. But still, after reboot, the "MaxBack Engine" process is back. I did notice though that it only appears when logging in with my usual user account; with another account it wasn't launched. So, dear Mac gurus, what could I do about this pest? I guess I could fall back to some Unix hackery and write a cronjob that kills any process with that name, but obviously it'd be nicer to be able to clean up from my computer everything left behind by Maxtor's piece of software.

  Read the article

• Vista Screen resolution Changes when Switching Users

  - by Benjol

  I regularly have a problem when switching between users in Vista - the screen resolution drops down to 800x600. If I try to set the resolution back to the maximum, it says nothing, but just keeps it at 800x600. I can set it back to an intermediate value. Otherwise I have to either restart the PC, or sometimes if I log off one of the users, I can then set the resolution back to max. Might it also have something to do with using sleep mode instead of performing regular shutdowns? I thought it might be related to the desktop background image taking up too much space, but even with plain colours, the problem still occurs. There is an enormous thread on this here, but not really any answers. From what I can gather from that thread, it isn't related to any particular applications, nor limited to a particular make of graphics card or monitor, so I don't think that including hardware details is useful. This is a very annoying problem, as it screws up my desktop and screen layout every single time. Has anyone here experienced this problem or found a solution? I've noticed that Windows Update has tried to install nVidia updates and apparently they've failed on several occasions. Not sure if that is of any relevance or not. UPDATE The last post on the thread: FWIW - I had this problem for about 2 years and wrote a number of posts in this thread in the past. It survived OS reinstallation, change of practically all of my hardware piece by piece (mobo, cpu, monitor, graphics card, memory, power supply...) I used to be affected by this annoying problem at least once every 24-48 hours. About 1.5 months ago I wiped out my 32 bit vista ultimate installation and installed Windows7 ultimate 64 bit from scratch and never saw this problem again. GOOD RIDDANCE. Vista was a pathetic piece of __ that felt like a flashback to the old [horrible] NT4/Windows95 days. I was seriously considering switching over to Apple/Mac OSX if this problem persisted.

  Read the article

• How can I batch convert SVG files containing text to PDF files (specifically on CentOS 5.3 x86_64)?

  - by molecules

  I would like to programatically convert SVG files to PDF files. However, the SVG files contain text that must be searchable in the generated PDF files. Also, it has to work on Red Hat Enterprise Linux 5.3 or CentOS 5.3 for the x86_64 architecture. It would be nice if it were Open Source or at least not very expensive. Here is what I've tried. All of these, except Batik, work fine on Debian Lenny. Inkscape I can get it installed using autopackages from http://inkscape.modevia.com/ap, but when I use it from the command line, the text is not searchable. Batik rasterizer [sic] When it converts SVG files to PDF files, the text is no longer searchable. svg2pdf The source for this and several of its dependencies are available to download. I have been trying to get it to compile on CentOS, but haven't had success yet. I found a precompiled version for Debian x86_64, but it doesn't work on CentOS. rsvg-convert Generated PDF isn't searchable on CentOS 5.3. Perhaps installing a newer version of cairo would help. Thanks to DaveParillo for mentioning rsvg-convert (on superuser). SOLUTION (but perhaps some of the above will still be useful to the reader) princeXML It works fine on CentOS when installed from source. For some reason it doesn't work when installed from the .rpm. Thanks Erik Dahlström! (provided solution that worked for my case on stackoverflow) Cross posted on stackoverflow

  Read the article

• Doing port forwarding and then using it from within the internal network

  - by Ram Rachum

  We all know that by doing port forwarding on the router, computers from outside the network are able, on the specified ports, to access internal computers by targeting the external IP. I'm now replacing a TP-Link router with a D-link VDSL N 6740U router, (and copied over all the settings,) and I've noticed that one thing stopped working: With the TP-link router, you could access those port-forwarded computers from within the network, using the external IP, and they would be forwarded to the relevant computers. With the new D-Link router, it doesn't work. You might be wondering, why would you want to use the external IP and port forwarding when you're inside the internal network anyway and can just access the internal IP? One example for why this is useful: You have an iPhone app that connects to a service on an internal computer. The iPhone app knows to connect to the external IP. When we put that iPhone inside the internal network (via WiFi), it suddenly stops working, because it can't access the service from the external IP anymore. Is it an inherent property of D-Link routers that they do not allow accessing internal servers from inside the network by targeting the external IP? Or is there a way to make it work?

  Read the article

• Preventing DDOS/SYN attacks (as far as possible)

  - by Godius

  Recently my CENTOS machine has been under many attacks. I run MRTG and the TCP connections graph shoots up like crazy when an attack is going on. It results in the machine becoming inaccessible. My MRTG graph: mrtg graph This is my current /etc/sysctl.conf config # Kernel sysctl configuration file for Red Hat Linux # # For binary values, 0 is disabled, 1 is enabled. See sysctl(8) and # sysctl.conf(5) for more details. # Controls IP packet forwarding net.ipv4.ip_forward = 0 # Controls source route verification net.ipv4.conf.default.rp_filter = 1 # Do not accept source routing net.ipv4.conf.default.accept_source_route = 0 # Controls the System Request debugging functionality of the kernel kernel.sysrq = 1 # Controls whether core dumps will append the PID to the core filename # Useful for debugging multi-threaded applications kernel.core_uses_pid = 1 # Controls the use of TCP syncookies net.ipv4.tcp_syncookies = 1 # Controls the maximum size of a message, in bytes kernel.msgmnb = 65536 # Controls the default maxmimum size of a mesage queue kernel.msgmax = 65536 # Controls the maximum shared segment size, in bytes kernel.shmmax = 68719476736 # Controls the maximum number of shared memory segments, in pages kernel.shmall = 4294967296 net.ipv4.conf.all.rp_filter = 1 net.ipv4.tcp_syncookies = 1 net.ipv4.icmp_echo_ignore_broadcasts = 1 net.ipv4.conf.all.accept_redirects = 0 net.ipv6.conf.all.accept_redirects = 0 net.ipv4.conf.all.send_redirects = 0 net.ipv4.conf.all.accept_source_route = 0 net.ipv4.conf.all.rp_filter = 1 net.ipv4.tcp_max_syn_backlog = 1280 Futher more in my Iptables file (/etc/sysconfig/iptables ) I only have this setup # Generated by iptables-save v1.3.5 on Mon Feb 14 07:07:31 2011 *filter :INPUT ACCEPT [1139630:287215872] :FORWARD ACCEPT [0:0] :OUTPUT ACCEPT [1222418:555508541] Together with the settings above, there are about 800 IP's blocked via the iptables file by lines like: -A INPUT -s 82.77.119.47 -j DROP These have all been added by my hoster, when Ive emailed them in the past about attacks. Im no expert, but im not sure if this is ideal. My question is, what are some good things to add to the iptables file and possibly other files which would make it harder for the attackers to attack my machine without closing out any non-attacking users. Thanks in advance!

  Read the article

• PHP displays blank white page even with all error reporting enabled

  - by Andy Shinn

  I am trying to debug a broken page in a Drupal application and am having a hard time getting PHP to spit anything useful out. I have the following set: error_reporting = E_ALL display_errors = On display_startup_errors = On log_errors = On error_log = /var/log/php/php_error.log I have a file showing me phpinfo() which confirms these variables are set correctly for the environment. I have increased memory_limit to 256M (which should be more than enough). Yet, the only indication I get is a status 500 code in the apache access log and a blank white page from PHP. The Apache virtual host has LogLevel set to debug and the error log only outputs: [Sat Jun 16 20:03:03 2012] [debug] mod_deflate.c(615): [client 173.8.175.217] Zlib: Compressed 0 to 2 : URL /index.php, referer: http://ec2-174-129-192-237.compute-1.amazonaws.com/admin/reports/updates [Sat Jun 16 20:03:03 2012] [error] [client 173.8.175.217] File does not exist: /var/www/favicon.ico [Sat Jun 16 20:03:03 2012] [debug] mod_deflate.c(615): [client 173.8.175.217] Zlib: Compressed 42 to 44 : URL /favicon.ico The PHP error log outputs nothing at all. kernel and syslog show nothing related to Apache or PHP. I have also tried installing suphp and checking its log just confirms the user is executing correctly: [Sat Jun 16 20:02:59 2012] [info] Executing "/var/www/index.php" as UID 1000, GID 1000 [Sat Jun 16 20:05:03 2012] [info] Executing "/var/www/index.php" as UID 1000, GID 1000 This is on Ubuntu 12.04 x86_64 with the following PHP modules: ii php5 5.3.10-1ubuntu3.1 server-side, HTML-embedded scripting language (metapackage) ii php5-cgi 5.3.10-1ubuntu3.1 server-side, HTML-embedded scripting language (CGI binary) ii php5-cli 5.3.10-1ubuntu3.1 command-line interpreter for the php5 scripting language ii php5-common 5.3.10-1ubuntu3.1 Common files for packages built from the php5 source ii php5-curl 5.3.10-1ubuntu3.1 CURL module for php5 ii php5-gd 5.3.10-1ubuntu3.1 GD module for php5 ii php5-mysql 5.3.10-1ubuntu3.1 MySQL module for php5 So, what am I missing here? Why no error reporting?

  Read the article

< Previous Page | 206 207 208 209 210 211 212 213 214 215 216 217  | Next Page >