Search Results

Search found 10860 results on 435 pages for 'bad blocks'.

Page 211/435 | < Previous Page | 207 208 209 210 211 212 213 214 215 216 217 218  | Next Page >

• Windows Firewall Software to Filter Transit Traffic

  - by soonts

  I need to test my networking code for Nintendo Wii under the conditions when some specific Internet server is not available. Wii is connected to my PC with crossover ethernet cable. PC has 2 NICs. PC is connected to hardware router with ethernet cable. The hardware router serves as NAT and has an internet connected to its uplink. I set the Wii to be in the same lan as PC by using Windows XP Network bridge. I can observe the WII network traffic using e.g. Wireshark sniffer. Is there a software firewall that can selectively filter out transit traffic? (e.g. block outgoing TCP connections to 123.45.67.89 to port 443) I tried Outpost Pro 2009 and Comodo. Outpost firewall blocks all transit traffic with it's implicit "block transit packet" rule. If the transit traffic is explicitly allowed by creating the system-wide low level rule, then it's allowed completely and no other filter can selectively block it. Comodo firewall only process rules when the packet has localhost's IP as either source or destination, allowing the rest of the traffic. Any ideas? Thanks in advance! P.S. Platform is Windows XP 32 bit, no other OSes is allowed, Windows ICS (Internet Connection Sharing) doesnt work since the Wii is unable to connect, becides I don't like the idea of adding one more level of NAT.

  Read the article

• 9000+ different subdomains 301 to main domain, .htacess apache

  - by Karim

  I bought a domain that had various subdomains such as Kim.domain.com/whatever john.domain.com/whatever1 Lizo.domain.com/whatever2 Simon.domain.com/whatever1 And this was in the thousands, and also had links to these pages I'd like to do a 301 redirect for all these urls into http://domain.com Any idea how this could be done? This is for a apache web server and needs to be done via .htaccess I have implemented the solution from reading the answer below. RewriteEngine On RewriteCond %{HTTP_HOST} !^www. domain.com$ RewriteCond %{HTTP_HOST} !^$ RewriteRule ^/(.*)$ http:/ / www. domain.com/$1 [L,R=301] However I have a slight problem, I would like to redirect all subdomains + subfolders to http://www. domain.com/ With the exception of http: //domain. com/subfolder/, in which case I would like to redirect to http: // www.domain. com/subfolder/ [i.e. exception for no subdomain] I'm guessing I need to add an exception, what can I do to implement this. Note: example URLs above have had spaces added to them to prevent spam blocks for blocking the post.

  Read the article

• iptables secure squid proxy

  - by Lytithwyn

  I have a setup where my incoming internet connection feeds into a squid proxy/caching server, and from there into my local wireless router. On the wan side of the proxy server, I have eth0 with address 208.78.∗∗∗.∗∗∗ On the lan side of the proxy server, I have eth1 with address 192.168.2.1 Traffic from my lan gets forwarded through the proxy transparently to the internet via the following rules. Note that traffic from the squid server itself is also routed through the proxy/cache, and this is on purpose: # iptables forwarding iptables -A FORWARD -i eth1 -o eth0 -s 192.168.2.0/24 -m state --state NEW -j ACCEPT iptables -A FORWARD -m state --state ESTABLISHED,RELATED -j ACCEPT iptables -A POSTROUTING -t nat -j MASQUERADE # iptables for squid transparent proxy iptables -t nat -A PREROUTING -i eth1 -p tcp --dport 80 -j DNAT --to 192.168.2.1:3128 iptables -t nat -A PREROUTING -i eth0 -p tcp --dport 80 -j REDIRECT --to-port 3128 How can I set up iptables to block any connections made to my server from the outside, while not blocking anything initiated from the inside? I have tried doing: iptables -A INPUT -i eth0 -s 192.168.2.0/24 -j ACCEPT iptables -A INPUT -i eth0 -j REJECT But this blocks everything. I have also tried reversing the order of those commands in case I got that part wrong, but that didn't help. I guess I don't fully understand everything about iptables. Any ideas?

  Read the article

• convert a logical partition to a primary partition

  - by ant2009

  Hello, Fedora 14 xfce I have the following partition setup. I would like to know how can I convert the logical partition sda6 to a primary partition. Disk /dev/sda: 320.1 GB, 320072933376 bytes 255 heads, 63 sectors/track, 38913 cylinders, total 625142448 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x1707a8a5 Device Boot Start End Blocks Id System /dev/sda1 2048 1026047 512000 83 Linux /dev/sda2 1026048 205844479 102409216 83 Linux /dev/sda3 205844480 214228991 4192256 82 Linux swap / Solaris /dev/sda4 214228992 625141759 205456384 5 Extended /dev/sda5 214231040 573562879 179665920 83 Linux /dev/sda6 573564928 625141759 25788416 7 HPFS/NTFS Filesystem Size Used Avail Use% Mounted on /dev/sda2 97G 5.0G 91G 6% / tmpfs 494M 176K 494M 1% /dev/shm /dev/sda1 485M 68M 392M 15% /boot /dev/sda5 169G 26G 135G 16% /home # partition table of /dev/sda unit: sectors /dev/sda1 : start= 2048, size= 1024000, Id=83 /dev/sda2 : start= 1026048, size=204818432, Id=83 /dev/sda3 : start=205844480, size= 8384512, Id=82 /dev/sda4 : start=214228992, size=410912768, Id= 5 /dev/sda5 : start=214231040, size=359331840, Id=83 /dev/sda6 : start=573564928, size= 51576832, Id= 7 I would like to convert sda6 to a primary partition, the reason for this it to install windows 7 starter. Many thanks for any suggestions,

  Read the article

• nginx projects in subfolders

  - by Timothy

  I'm getting frustrated with my nginx configuration and so I'm asking for help in writing my config file to serve multiple projects from sub-directories in the same root. This isn't virtual hosting as they are all using the same host value. Perhaps an example will clarify my attempt: request 192.168.1.1/ should serve index.php from /var/www/public/ request 192.168.1.1/wiki/ should serve index.php from /var/www/wiki/public/ request 192.168.1.1/blog/ should serve index.php from /var/www/blog/public/ These projects are using PHP and use fastcgi. My current configuration is very minimal. server { listen 80 default; server_name localhost; access_log /var/log/nginx/localhost.access.log; root /var/www; index index.php index.html; location ~ \.php$ { fastcgi_pass 127.0.0.1:9000; fastcgi_index index.php; fastcgi_param SCRIPT_FILENAME /var/www$fastcgi_script_name; include fastcgi_params; } } I've tried various things with alias and rewrite but was not able to get things set correctly for fastcgi. It seems there should be a more eloquent way than writing location blocks and duplicating root, index, SCRIPT_FILENAME, etc. Any pointers to get me headed in the right direction are appreciated.

  Read the article

• fail2ban block ports rules iptable

  - by J Spen

  I just installed Ubuntu Server 14.04 and don't have much experience with IPtables. I am trying to get a basic setup going where I only accept SSH connections on port 22 and 2222. I actually have that working with no problem using fail2ban ssh. Then I wanted to block all other ports except 423 and 4242 but either method of DROPing all connections that are not listed seems not to work and it blocks me out of everything. Below is the setup that works: -P INPUT ACCEPT -P FORWARD ACCEPT -P OUTPUT ACCEPT -N fail2ban-ssh -A INPUT -p tcp -m multiport --dports 22,2222 -j fail2ban-ssh -A fail2ban-ssh -j RETURN I tried to change it either to: -P INPUT DROP -P FORWARD ACCEPT -P OUTPUT ACCEPT -N fail2ban-ssh -A INPUT -p tcp -m multiport --dports 22,2222 -j fail2ban-ssh -A fail2ban-ssh -j RETURN or: -P INPUT ACCEPT -P FORWARD ACCEPT -P OUTPUT ACCEPT -N fail2ban-ssh -A INPUT -p tcp -m multiport --dports 22,2222 -j fail2ban-ssh -A INPUT -j DROP -A fail2ban-ssh -j RETURN I have noticed that the rules for fail2ban-ssh are automatically added to my iptables on boot because if I save them with iptables-persistant they are entered twice. How do I go about blocking everything accept those 2 ports using fail2ban? Is it a bad fail2ban configuration or do I need to add the fail2ban-ssh -j Return somewhere else in my code.

  Read the article

• How to work around blocked outbound hkp port for apt keys

  - by kief_morris

  I'm using Ubuntu 9.10, and need to add some apt repositories. Unfortunately, I get messages like this when running sudo apt-get update: W: GPG error: http://ppa.launchpad.net karmic Release: The following signatures couldn't be verified because the public key is not available: NO_PUBKEY 5A9BF3BB4E5E17B5 W: GPG error: http://ppa.launchpad.net karmic Release: The following signatures couldn't be verified because the public key is not available: NO_PUBKEY 1DABDBB4CEC06767 So, I need to install the keys for these repositories. Under 9.10 we now have the option to do this: sudo add-apt-repository ppa:nvidia-vdpau/ppa See this Ubuntu help article for details. This is great, except that I'm running this on a workstation behind a firewall which blocks outbound connections to pretty much all ports except those required by secretaries running Windows and IE. The port in question here is the hkp service, port 11371. There appear to be ways to manually download keys and install them on apt's keyring. There may even be a way to use add-apt-repository or wget or something to download a key from an alternative server making it available on port 80. However, I haven't yet found a concise set of steps for doing so. What I'm looking for is: How to find a public key for an apt-package (recommendations for resources which have these, and/or tips for searching. Searching for the key hash doesn't seem all that effective so far.) How to retrieve a key (can it be done automatically using gpg or add-apt-repository?) How to add a key to apt's keyring Thanks in advance.

  Read the article

• Cannot load from raid with grub

  - by Andrew Answer

  I have a RAID1 array on my Ubuntu 12.04 LTS and my /sda HDD has been replaced several days ago. I use this commands to replace: # go to superuser sudo bash # see RAID state mdadm -Q -D /dev/md0 # State should be "clean, degraded" # remove broken disk from RAID mdadm /dev/md0 --fail /dev/sda1 mdadm /dev/md0 --remove /dev/sda1 # see partitions fdisk -l # shutdown computer shutdown now # physically replace old disk by new # start system again # see partitions fdisk -l # copy partitions from sdb to sda sfdisk -d /dev/sdb | sfdisk /dev/sda # recreate id for sda sfdisk --change-id /dev/sda 1 fd # add sda1 to RAID mdadm /dev/md0 --add /dev/sda1 # see RAID state mdadm -Q -D /dev/md0 # State should be "clean, degraded, recovering" # to see status you can use cat /proc/mdstat After bebuilding completion "fdisk -l" says what I have not valid partition table /dev/md0. So 1) "update-grub" find only /sda and /sdb Linux, not /md0 2) "dpkg-reconfigure grub-pc" says "GRUB failed to install the following devices /dev/md0" I cannot load my system except from /sdb1 and /sda1, but in DEGRADED mode... This is my partial fdisk -l output: Disk /dev/sdb: 500.1 GB, 500107862016 bytes 255 heads, 63 sectors/track, 60801 cylinders, total 976773168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x000667ca Device Boot Start End Blocks Id System /dev/sdb1 * 63 940910984 470455461 fd Linux raid autodetect /dev/sdb2 940910985 976768064 17928540 5 Extended /dev/sdb5 940911048 976768064 17928508+ 82 Linux swap / Solaris Disk /dev/md0: 481.7 GB, 481746288640 bytes 2 heads, 4 sectors/track, 117613840 cylinders, total 940910720 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Disk /dev/md0 doesn't contain a valid partition table Anybody can resolve this issue? I have big headache with this.

  Read the article

• Connecting to my home router web interface from work

  - by Joe

  Hi, I'm trying to connect to my home router web interface from work. I use dyndns, because I don't have a static IP at home, and it works perfectly from any other place except my workplace (update: I made a mistake, see edit below). When trying to access the web interface from work I get a "500 Server Error" with the code: SERVER_RESPONSE_RESET. I'm not trying to use any protocols such as remote desktop, I'm only trying to access the web interface. I can access any other web page from my workplace with no problems, and I think my router web interface is like any other web page, isn't it? I thought maybe my work place proxy blocks addresses of services like dyndns, so I also applied another trick. Since I have a web page on my own domain (say www.mydomain.com) which I can access from work, I tried adding a CNAME to my domain which is linked to the dyndns address (router.mydomain.com). This way if anyone enters the address router.mydomain.com from anywhere, they reach my home router web interface, and there's no way of knowing it's a dyndns address (or is there?). However, it still doesn't work from my workplace (I get the same error message). Any ides? Edit: I'm sorry to say I made a mistake earlier. I used to be able to access my home router web interface from my old workplace, and I thought it was still possible since I don't recall making any configuration changes. However, after reading the replies, I went over to my old workplace and checked, and it doesn't work from there either. I'm very sorry for giving out wrong and misleading information about my problem. So to summarize: my problem is that I can't access my home router web interface from anywhere.

  Read the article

• Allignment of ext3 partition on LVM RAID volume group

  - by John P

  I'm trying to add a partition on a LVM that resides on a RAID6 volume group and fdisk is complaining about the partition not residing on a physical sector boundry. My question is, how do you calculate the correct starting sector for a partition on a LVM? This partition will be formated ext3. Would it be better to just format the LVM directly instead of creating a new partition? Disk /dev/dedvol/backup: 2199.0 GB, 2199023255552 bytes 255 heads, 63 sectors/track, 267349 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 1048576 bytes / 8388608 bytes Disk identifier: 0x4e428f49 Device Boot Start End Blocks Id System /dev/dedvol/backup1 63 267349 2146982827+ 83 Linux Partition 1 does not start on physical sector boundary. lvdisplay /dev/dedvol/backup --- Logical volume --- LV Name /dev/dedvol/backup VG Name dedvol LV UUID OV2n5j-7LHb-exJL-t8dI-dU8A-2vxf-uIicCt LV Write Access read/write LV Status available # open 0 LV Size 2.00 TiB Current LE 524288 Segments 1 Allocation inherit Read ahead sectors auto - currently set to 32768 Block device 253:1 vgdisplay dedvol --- Volume group --- VG Name dedvol System ID Format lvm2 Metadata Areas 1 Metadata Sequence No 3 VG Access read/write VG Status resizable MAX LV 0 Cur LV 2 Open LV 1 Max PV 0 Cur PV 1 Act PV 1 VG Size 14.55 TiB PE Size 4.00 MiB Total PE 3815448 Alloc PE / Size 3670016 / 14.00 TiB Free PE / Size 145432 / 568.09 GiB VG UUID 8fBcOk-aXGx-P3Qy-VVpJ-0zK1-fQgy-Cb691J

  Read the article

• Solaris 10: How to image a machine?

  - by nonot1

  I've got a Solaris 10 workstation that I'd like to create a full image backup from. The machine has 2 drives, one UFS for system root, and 1 ZFS for data storage. I intend to add a third HD to keep the backup images of both primary drives (including any zfs snapshots). The purpose is not disaster recovery, but rather to allow me to easily blow away a series of application installation/configuration changes I intend to try. What's the best way to do this? I'm not too familiar with Solaris, but have some basic Linux knowledge. I looked at CloneZilla, but it does not support Solaris. I'm OK with just a dd | gzip > image style solution, but I'd need some way to first zero-out the non-used blocks on the primary drives to aid gzip. They are are much larger than my 3rd drive, but hardly have any real data. Update to clarify: I specifically want to avoid using any file-system snapshot functionality, because part of the app configuration changes involve/depend slightly on existing and new snapshots. Ideally the full collection of snapshots should be part of the backup. Virtualization not an option, because the goal is to do performance evaluation on a very specific HW configuration. For the same reason, the spurious "back up" snapshots could skew performance data. Thank you

  Read the article

• Determining the Source of a Given File System Mount on Unix [migrated]

  - by phobos51594

  Background Recently I have run into a bit of a snag on my home FreeBSD server. I recently upgraded it to the latest stable release, and I have noticed some strange behavior with the /var partition. Originally, I had the system configured such that /var had its own partition with /var/run and /var/log in memory disks (/tmp, too). After the upgrade, I notice there is a new, fourth memory disk mounting directly to /var that I had not set up manually and is not in my fstab. It is only 28 megs or so in size and is causing problems when trying to update my ports collection. The ramdisk mounts atuomagically at boot and cannot be unmounted while in multi-user mode. If I drop to single user mode, I am able to unmount it without issue, however rebooting causes it to pop right back up. System specifications have been included at the end of the post. Question Is there any way to determine exactly what is mounting a given memory disk (or any filesystem, for that matter) after it has been mounted? Alternately, does anybody have any ideas what might have caused the new /var ramdisk to pop up? System Specification # uname -a FreeBSD sarge 9.1-PRERELEASE FreeBSD 9.1-PRERELEASE #0: Thu Nov 22 14:02:13 PST 2012 donut@sarge:/usr/obj/usr/src/sys/GENERIC i386 # df Filesystem 1K-blocks Used Avail Capacity Mounted on /dev/da0s1a 515612 410728 63636 87% / devfs 1 1 0 100% /dev /dev/da0s1d 515612 287616 186748 61% /var /dev/da0s1e 6667808 2292824 3841560 37% /usr /dev/md0 63004 32 57932 0% /tmp /dev/md1 3484 8 3200 0% /var/run /dev/md2 31260 8 28752 0% /var/log /dev/md3 31260 512 28248 2% /var <-- This # cat /etc/fstab # Device Mountpoint FStype Options Dump Pass# /dev/da0s1a / ufs rw,noatime 1 1 /dev/da0s1d /var ufs rw,noatime 2 2 /dev/da0s1e /usr ufs rw,noatime 2 2 md /tmp mfs rw,-s64M,noatime 0 0 md /var/run mfs rw,-s4M,noatime 0 0 md /var/log mfs rw,-s32M,noatime 0 0 Thank you in advance for any assistance.

  Read the article

• How to create a software raid5 array without a spare

  - by Yannick M.

  I am trying to create a software raid5 array using mdadm: $ linux # mdadm --create --verbose /dev/md0 --level=5 --raid-devices=4 --spare-devices=0 /dev/sda1 /dev/sdb1 /dev/sdc1 /dev/sdd1 mdadm: layout defaults to left-symmetric mdadm: chunk size defaults to 64K mdadm: array /dev/md0 started. However when inspecting /proc/mdstat Personalities : [raid6] [raid5] [raid4] md0 : active raid5 sdd1[4] sdc1[2] sdb1[1] sda1[0] 2930279808 blocks level 5, 64k chunk, algorithm 2 [4/3] [UUU_] [>....................] recovery = 0.3% (2970496/976759936) finish=186.1min speed=87172K/sec unused devices: <none> It seems one drive isn't active, so I check the details of the array: /dev/md0: Version : 00.90.03 Creation Time : Tue Jul 21 16:29:53 2009 Raid Level : raid5 Array Size : 2930279808 (2794.53 GiB 3000.61 GB) Used Dev Size : 976759936 (931.51 GiB 1000.20 GB) Raid Devices : 4 Total Devices : 4 Preferred Minor : 0 Persistence : Superblock is persistent Update Time : Tue Jul 21 16:29:53 2009 State : clean, degraded, recovering Active Devices : 3 Working Devices : 4 Failed Devices : 0 Spare Devices : 1 Layout : left-symmetric Chunk Size : 64K Rebuild Status : 0% complete UUID : ce8b2f40:821d003c:0027688e:a70977ec Events : 0.1 Number Major Minor RaidDevice State 0 8 1 0 active sync /dev/sda1 1 8 17 1 active sync /dev/sdb1 2 8 33 2 active sync /dev/sdc1 4 8 49 3 spare rebuilding /dev/sdd1 And it seems there are only 3 active devices, with one spare. Is it just me, or something wrong here?

  Read the article

• IPSec VPN using ZyWALL IPSec VPN Client: unable to connect from some providers

  - by Reshi

  I'm trying to configure an IPSec VPN to one company from my home. The company has SANET internet service provider. I was able to create a VPN connection from another company that has the same internet service provider. The problem begins when I'm trying to connect from another ISP like Orange or Telekom. Here is the log from ZyWall: 20120816 10:06:18:359 Default (SA Gateway-P1) SEND phase 1 Main Mode [SA] [VID] [VID] [VID] [VID] [VID] 20120816 10:06:18:375 Default (SA Gateway-P1) RECV phase 1 Main Mode [SA] [VID] [VID] [VID] [VID] [VID] [VID] [VID] [VID] 20120816 10:06:18:390 Default (SA Gateway-P1) SEND phase 1 Main Mode [KEY_EXCH] [NONCE] [NAT_D] [NAT_D] 20120816 10:06:18:718 Default (SA Gateway-P1) RECV phase 1 Main Mode [KEY_EXCH] [NONCE] [NAT_D] [NAT_D] 20120816 10:06:18:734 Default (SA Gateway-P1) SEND phase 1 Main Mode [HASH] [ID] 20120816 10:06:18:750 Default (SA Gateway-P1) RECV phase 1 Main Mode [HASH] [ID] 20120816 10:06:18:750 Default phase 1 done: initiator id [email protected], responder id 111.112.113.114 20120816 10:06:18:765 Default (SA Gateway-Tunnel-P2) SEND phase 2 Quick Mode [HASH] [SA] [KEY_EXCH] [NONCE] [ID] [ID] 20120816 10:06:18:953 Default (SA Gateway-Tunnel-P2) RECV phase 2 Quick Mode [HASH] [SA] [KEY_EXCH] [NONCE] [ID] [ID] 20120816 10:06:18:953 Default (SA Gateway-Tunnel-P2) SEND phase 2 Quick Mode [HASH] 20120816 10:06:48:968 Default (SA Gateway-P1) SEND Informational [HASH] [NOTIFY] type DPD_R_U_THERE 20120816 10:06:48:984 Default (SA Gateway-P1) RECV Informational [HASH] [NOTIFY] type DPD_R_U_THERE_ACK ZyWall informs me that the tunnel was opened. But I can't ping or access any computer in the network. My configuration at home: ISP: Orange Optical connection Terminal: GPON OPTICAL NETWORK TERMINAL G-25E Router: TPLink TL-WR941N --> SPI Firewall Enabled --> VPN - IPSEC Passthrough Enabled I was wondering if the problem could not be on ISP side (that he blocks somehow this connection because in SANET ISP it worked fine) or even in my terminal or router. What could I check? Where could be the problem ?

  Read the article

• Wireless card on HP laptop not working

  - by D. Strout

  I just bought an HP Envy m6-1125dx online from Best Buy. When I got it home and started it up, the wireless card did not work well - at all. I could connect, but any real usage would cause the connection to start dropping every 30 seconds or so, and it would be really slow. Taking another look at the reviews on the Best Buy site, it seems only a few others had this problem, so I took it to my local Best Buy and exchanged it for another unit. Got it home again and the card had the same issues. Which leads to my dilemma. First: does this model have several different cards that it could come with? Mine is a Ralink RT5390R (on both units I received). If it does, then I can keep exchanging until I get a unit with a different card. I wouldn't ask this, except it seems weird that only a few people mentioned this issue, so I thought that might be one possibility. I looked in to replacing the card with a different one myself, but it seems that HP blocks certain wireless cards. However, some people reported success in replacing the card, and this site said it was only an issue on "older HP computer[s]". Can anyone confirm this? Finally, if that fails/will not work, does anyone know what I can get through Best Buy? I am concerned that they will not put any different card than the Ralink, and after two of those, I don't want that. Can I ask Best Buy support to use a different card? Can they even get another card from HP? I guess the base question is: should I attempt to replace the card myself (two days via Amazon to get a new card), should I try to get the laptop repaired through Best Buy (two - four weeks), should I go for a different model laptop from Best Buy, or should I try a different unit of the same model (three's the charm?).

  Read the article

• Software/hardware to build video streaming server?

  - by Sasha Yanovets

  I am looking for a video streaming server solution, something like online TV server, with ability to make live broadcasts in the internet. What software could you recommend for that? What kind of hardware it should run on, should be there anything special? I am looking for a solution that could be scaled up to at least 1000 simultaneous users online with good resolution of video. I think it is good to have general answer on what direction to choose. But here more details on my specific case: I just looking for a solution almost from scratch. We have some video content that we've produced, but it is not delivered over internet yet. We do not tied to any particular vendor for now. We want to make 24 hours of steaming three 8 hour blocks with change of content every day. We want the ability to make regular live broadcasts. I guess we will need to have several options of streaming quality (low ~56 kb/s mid ~273 kb/s). Some terms just foreign to me (like play-truncation rate), if you could point out what parameters we should avare of, it would be great. Uplink to the internet is to be determined. We plan to start from something and scale up on the way. If you are already have some kind of media streaming server, just describe its configuration here (hardware, OS, software), peak number of concurrent users it serves. I think it could help people approaching this task.

  Read the article

• How can I format an SD card with a more robust Linux-usable filesystem with a specific cluster size for better write performace?

  - by Harvey

  Goal: microSD card formatted... for best write performance for use only with embedded Linux for better reliability (random power failures may occur) using an 64kB cluster size I'm using an 8GB microSD card for data storage inside an embedded Linux/ARM device. The SD card is not removable. I've been using ext3 instead of the pre-installed FAT32 because it seems to better handle random power failures during writes. However, I kept noticing that my write performance is always best with the pre-installed FAT32 from Kingston. If I reformat the card with FAT32, the performance still suffers. After browsing wikipedia, I stumbled upon the following comment saying that some cards are optimized for specific cluster sizes. In my case, the Kingston comes pre-formatted for an 64kB cluster size. Risks of reformatting Reformatting an SD card with a different file system, or even with the same one, may make the card slower, or shorten its lifespan. Some cards use wear leveling, in which frequently modified blocks are mapped to different portions of memory at different times, and some wear-leveling algorithms are designed for the access patterns typical of the file allocation table on a FAT16 or FAT32 device.[60] In addition, the preformatted file system may use a cluster size that matches the erase region of the physical memory on the card; reformatting may change the cluster size and make writes less efficient.

  Read the article

• Virus on site but can't find where

  - by Rob

  WARNING! THIS IS ABOUT A VIRUS ON MY SITE. IT APPEARS IT HAS BEEN THERE FOR SOMETIME AND I'VE HAD NO PROBLEMS. BUT PLEASE BE CAREFUL. READ EVERYTHING I SAY AND SEE IF YOU CAN HELP ME WITHOUT VISITING THE LINK. AVG PICKS UP ON IT AND BLOCKS IT, MCAFEE DOES NOT. Sorry about the warning, obviously i'm not here to get anyone infected or anything like that. Basically I run the website sortitoutsi dot net. Ages ago I got a virus on my computer, they got hold of my FTP passwords and added some lines of javascript to the top of my site. I removed them and believe it was fixed. However i'm using the "Web Developer" extension for Firefox and chose to view all javascript on my page and find there are various links to horrible urls such as: gittigidiyor-com.excite.co.jp.webmasterworld-com.eastmusicdirect.ru:8080/aboutus.org/aboutus.org/google.com/skycn.com/torrents.ru.php and gittigidiyor-com.excite.co.jp.webmasterworld-com.eastmusicdirect.ru:8080/index.php?jl= These terms do not appear anywhere. In the source code, in any of the javascript or the css. I also can't see that there are any rogue images that I don't recognise either. So i've no idea where this javascript is coming from. Can anyone suggest how I can find references to these links and remove them? I can see them both in the Web Developer firefox extension and in the net tab using Firebug. Any help would be greatly appreciated

  Read the article

• Dual-booting Ubuntu and Pardus with GRUB2...Pardus no show?

  - by Ibn Ali al-Turki

  I have Ubuntu 10.10 installed and used to dual-boot Fedora, but I replaced Fedora with Pardus. After the install, I went into ubuntu, and did a sudo update-grub. It detected my Pardus 2011 install there. When I rebooted, it did not show up in my grub2 menu however. I went back to Ubuntu and did it again...then checked the grub.cfg, and it is not there. I have read that Pardus uses a grub legacy. How can I get Pardus into my grub2 menu? Thanks! sudo fdisk -l Disk /dev/sda: 500.1 GB, 500107862016 bytes 255 heads, 63 sectors/track, 60801 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0xd9b3496e Device Boot Start End Blocks Id System /dev/sda1 * 1 15197 122067968 83 Linux /dev/sda2 36394 60802 196059757 5 Extended /dev/sda3 15197 30394 122067968 83 Linux /dev/sda5 36394 59434 185075308 7 HPFS/NTFS /dev/sda6 59434 60802 10983424 82 Linux swap / Solaris Partition table entries are not in disk order and update-grub Found linux image: /boot/vmlinuz-2.6.35-25-generic Found initrd image: /boot/initrd.img-2.6.35-25-generic Found memtest86+ image: /boot/memtest86+.bin Found Pardus 2011 (2011) on /dev/sda3 Yet after this, I go to grub.cfg, and Pardus is not there.

  Read the article

• IPtables - Accept Arbitrary Packets

  - by Asad Moeen

  I've achieved a lot on blocking attacks on GameServers but I'm stuck on something. I've blocked major requests of game-server which it aceepts in the form "\xff\xff\xff\xff" which can be followed by the actual queries like get status or get info to make something like "\xff\xff\xff\xff getstatus " but I see other queries if sent to the game-server will cause it to reply with a "disconnect" packet with the same rate as input so if the input rate is high then the high output of "disconnect" might give lag to the server. Hence I want to block all queries except the ones actual clients use which I suppose are in the form "\xff\xff\xff\xff" or .... so, I tried using this rule : -A INPUT -p udp -m udp -m u32 ! --u32 0x1c=0xffffffff -j ACCEPT -A INPUT -p udp -m udp -m recent --set --name Total --rsource -A INPUT -p udp -m udp -m recent --update --seconds 1 --hitcount 20 --name Total --rsource -j DROP Now where the rule does accept the clients but it only blocks requests in the form "\xff\xff\xff\xff getstatus " ( by which GameServer replies with status ) and not just "getstatus " ( by which GameServer replies with disconnect packet ). So I suppose the accept rule is accepting the simple "string" as well. I actually want it to also block the non-(\xff) queries. So how do I modify the rule?

  Read the article

• RHEL Java Application returns "No space left on device" but only 3% used

  - by FiveO

  My Java Application returns following Exception when saving a new file in /opt/wso2 on a CentOS 6.4: Caused by java.io.FileNotFoundException: ... (No space left on device) Caused by: java.io.FileNotFoundException: /opt/wso2/FrameworkFiles/trk_2014062500042488825_TRCK_PatfallHospis_pFromHospis_66601fb3-a03c-4149-93c3-6892e0a10fea.txt (No space left on device) at java.io.FileOutputStream.open(Native Method) at java.io.FileOutputStream.<init>(FileOutputStream.java:212) at java.io.FileOutputStream.<init>(FileOutputStream.java:99) at com.avintis.esb.framework.adapter.wso2.FrameworkAdapterWSO2.sendMessages(FrameworkAdapterWSO2.java:634) ... 23 more But when I run df -a I can see that the partition still has plenty of space available: [root@stzsi466 wso2]# df -a Filesystem 1K-blocks Used Available Use% Mounted on /dev/mapper/vg_stzsi466-lv_root 12054824 2116092 9326380 19% / proc 0 0 0 - /proc sysfs 0 0 0 - /sys devpts 0 0 0 - /dev/pts tmpfs 4030764 0 4030764 0% /dev/shm /dev/sda1 495844 53858 416386 12% /boot /dev/sdb1 51605436 1424288 47559744 3% /opt/wso2 none 0 0 0 - /proc/sys/fs/binfmt_misc [root@stzsi466 ~]# df -i Filesystem Inodes IUsed IFree IUse% Mounted on /dev/mapper/vg_stzsi466-lv_root 765536 45181 720355 6% / tmpfs 1007691 1 1007690 1% /dev/shm /dev/sda1 128016 44 127972 1% /boot /dev/sdb1 3276800 6137 3270663 1% /opt/wso2 What is the problem here? Is it caused by the Java on CentOS 6.4? I have another server running Redhat REHL 6.4 and all works fine - same Java etc. Does anyone know of this problem?

  Read the article

• Is my OCZ SSD aligned correctly? (Linux)

  - by Barney Gumble

  I have an OCZ Agility 2 SSD with 40 GB of space. I use it as a system drive in Debian Linux (Squeeze) and in my opinion it's really fast. But I've read a lot on aligning partitions and file systems... And I'm not sure if I succeeded in aligning the partitions correctly. Maybe the SSD could be even faster?? ;-) I use ext4 and here is the output of fdisk -cul: Disk /dev/sda: 40.0 GB, 40018599936 bytes 255 heads, 63 sectors/track, 4865 cylinders, total 78161328 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: [...] Device Boot Start End Blocks Id System /dev/sda1 * 2048 73242623 36620288 83 Linux /dev/sda2 73244670 78159871 2457601 5 Extended /dev/sda5 73244672 78159871 2457600 82 Linux swap / Solaris My partitions were created just by the Debian Squeeze setup assistant. So I didn't care about the details of partitioning. But now I think maybe the installer didn't align it correctly? Actually, 2048 looks good to me (better than odd values like 63 or something like that) but I've no idea... ;-) Help plz! According to some "SSD Alignment Calculator" I found on the web, the OCZ SSDs have a NAND Erase Block Size of 512kB and their NAND Page Size is 4kB. 2048 is divisible by 4 and 512. So are the partitions aligned correctly?

  Read the article

• Ubuntu 12.04/12.10 can't detect windows or any other partitions(Asus z77 UEFI BIOS)

  - by user971155

  I've recently completed tinkering my new pc(motherboard ASUS z77 with UEFI BIOS) and unfortunately not everything works quite well. After installing windows 7 ultimate on a single primary partition(SATA drive) I decided to allocate one more logical partition for additional needs. When I tried doing it with the manager - it said that it couldn't allocate requested size even though I certainly asked for much less than it was available. I thought that it might have been a windows issue and proceded to installing Ubuntu 12.10 x64. When the graphical interface loaded it showed me a message stating that it can't find any other operating system on the drive. When I used custom partioning option it showed me none of my current partions(including that with windows). However, when I boot with "Try Ubuntu" feature it does find them ! I find it weird though. Here's what the console present me with: ubuntu@ubuntu:~$ sudo os-prober /dev/sda1:Windows 7 (loader):Windows:chain ubuntu@ubuntu:~$ sudo fdisk -l Disk /dev/sda: 640.1 GB, 640135028736 bytes 255 heads, 63 sectors/track, 77825 cylinders, total 1250263728 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00072b98 Device Boot Start End Blocks Id System /dev/sda1 * 2048 206847 102400 7 HPFS/NTFS/exFAT /dev/sda2 206848 100020223 49906688 7 HPFS/NTFS/exFAT /dev/sda3 100022270 1250263039 575120385 5 Extended /dev/sda4 566669312 1250263039 341796864 83 Linux I also tried creating partitions from disk utility which results in error: , Error creating partition: helper exited with exit code 1: In part_add_partition: device_file=/dev/sda, start=51211402240, size=1923000000, type=0x83 Entering MS-DOS parser (offset=0, size=640135028736) MSDOS_MAGIC found looking at part 0 (offset 1048576, size 104857600, type 0x07) new part entry looking at part 1 (offset 105906176, size 51104448512, type 0x07) new part entry looking at part 2 (offset 51211402240, size 588923274240, type 0x05) Entering MS-DOS extended parser (offset=51211402240, size=588923274240) readfrom = 51211402240 MSDOS_MAGIC found Exiting MS-DOS extended parser looking at part 3 (offset 290134687744, size 349999988736, type 0x83) new part entry Exiting MS-DOS parser MSDOS partition table detected containing partition table scheme = 1 got it Error: Can't have overlapping partitions. ped_disk_new() failed Here's what I get when I try to install the system i.stack.imgur.com/pjlb9.png, i.stack.imgur.com/g1lXN.png P.S. It's strange that I even can't create any more partitions neither with disk-utility nor with windows 7 native tools

  Read the article

• Windows 7 boots to black screen with blinking cursor

  - by murgatroid99

  I have an Alienware M17x that dual boots into Ubuntu 11.04 and Windows 7 Home Premium. Currently, the computer starts at the GRUB loader and will boot into Ubuntu, but if I try to boot into Windows, I immediately get a black screen with a blinking cursor in the upper left corner. The output of fdisk -l is Device Boot Start End Blocks Id System /dev/dm-0p1 1 5 40131 de Dell Utility Partition 1 does not start on physical sector boundary. /dev/dm-0p2 6 1918 15360000 7 HPFS/NTFS Partition 2 does not start on physical sector boundary. /dev/dm-0p3 * 1918 64772 504878877+ 7 HPFS/NTFS Partition 3 does not start on physical sector boundary. /dev/dm-0p4 64772 77827 104858625 5 Extended Partition 4 does not start on physical sector boundary. /dev/dm-0p5 64772 67204 19531008 83 Linux /dev/dm-0p6 67204 74498 58593536 83 Linux /dev/dm-0p7 74498 77577 24731648 83 Linux /dev/dm-0p8 77578 77827 2000128 82 Linux swap / Solaris I have used the Windows rescue CD, and run the automatic error fixer until it finds no errors. I have run chkdsk /R on both the main Windows 7 (/dev/dm-0p3) partition and the recovery partition (/dev/dm-0p2). I set the main Windows 7 partition to be active. I also tried running in the recovery console the commands bootrec /fixmbr bootrec /fixboot bootrec /rebuildbcd None of these helped and the last set of commands deletes grub, which I then have to reinstall from Ubuntu. I think the last thing I did in windows before this started was install the newest ATI driver for my video card. This would suggest using system restore, and I actually had a restore point earlier (after the problem started), but after whatever I did that restore point does not appear in the list on the recovery disk any more, so I cannot do a system restore. Is there anything else I can try to make Windows boot properly again? Edit: Running the suggested commands bootsect /nt60 c: bcdboot c:\windows /s c: was also ineffective.

  Read the article

• ExpressCache not working after Windows 8 reinstall on Samsung Series 7 Gamer

  - by Morven

  I have a Samsung Series 7 Gamer laptop which came with Windows 8. After doing a reinstall of Windows, the ExpressCache software is no longer caching. Running "eccmd -info" shows me that the software is present and it has the MSATA drive partition configured. However, it's not actually caching anything. These are the results after having the system booted for days: C:\windows\system32eccmd -info ExpressCache Command Version 1.0.94.0 Copyright¬ 2010-2012 Condusiv Technologies. Date Time: 11/3/2013 12:26:20:263 (JAMETHIEL #36) EC Cache Info ================================================== Mounted : Yes Partition Size : 7.46 GB Reserved Size : 3.00 MB Volume Size : 7.46 GB Total Used Size : 86.50 MB Total Free Space : 7.38 GB Used Data Size : 16.63 MB Used Data Size on Disk : 84.38 MB Tiered Cache Stats ================================================== Memory in use : 32.00 MB Blocks in use : 136 Read Percent : 0.02% Cache Stats ================================================== Cache Volume Drive Number : 1 Total Read Count : 97242 Total Read Size : 4.13 GB Total Cache Read Count : 0 Total Cache Read Size : 595.50 KB Total Write Count : 161546 Total Write Size : 5.89 GB Total Cache Write Count : 0 Total Cache Write Size : 0 Bytes Cache Read Percent : 0.01% Cache Write Percent : 0.00% As you can see on the last two lines, cache read and write percent is nigh on zero. Anyone know where to look next? The only guides I can find deal with ExpressCache not being present or not having a configured drive.

  Read the article

< Previous Page | 207 208 209 210 211 212 213 214 215 216 217 218  | Next Page >