Search Results

Search found 18781 results on 752 pages for 'ip port'.

Page 211/752 | < Previous Page | 207 208 209 210 211 212 213 214 215 216 217 218  | Next Page >

• FreeBSD 8.1 unstable network connection

  - by frankcheong

  I have three FreeBSD 8.1 running on three different hardware and therefore consist of different network adapter as well (bce, bge and igb). I found that the network connection is kind of unstable which I have tried to scp some 10MB file and found that I cannot always get the files completed successfully. I have further checked with my network admin and he claim that the problem is being caused by the network driver which cannot support the load whereby he tried to ping using huge packet size (around 15k) and my server will drop packet consistently at a regular interval. I found that this statement may not be valid since the three server is using three different network drive and it would be quite impossible that the same problem is being caused by three different network adapter and thus different network driver. Since then I have tried to tune up the performance by playing around with the /etc/sysctl.conf figures with no luck. kern.ipc.somaxconn=1024 kern.ipc.shmall=3276800 kern.ipc.shmmax=1638400000 # Security net.inet.ip.redirect=0 net.inet.ip.sourceroute=0 net.inet.ip.accept_sourceroute=0 net.inet.icmp.maskrepl=0 net.inet.icmp.log_redirect=0 net.inet.icmp.drop_redirect=1 net.inet.tcp.drop_synfin=1 # Security net.inet.udp.blackhole=1 net.inet.tcp.blackhole=2 # Required by pf net.inet.ip.forwarding=1 #Network Performance Tuning kern.ipc.maxsockbuf=16777216 net.inet.tcp.rfc1323=1 net.inet.tcp.sendbuf_max=16777216 net.inet.tcp.recvbuf_max=16777216 # Setting specifically for 1 or even 10Gbps network net.local.stream.sendspace=262144 net.local.stream.recvspace=262144 net.inet.tcp.local_slowstart_flightsize=10 net.inet.tcp.nolocaltimewait=1 net.inet.tcp.mssdflt=1460 net.inet.tcp.sendbuf_auto=1 net.inet.tcp.sendbuf_inc=16384 net.inet.tcp.recvbuf_auto=1 net.inet.tcp.recvbuf_inc=524288 net.inet.tcp.sendspace=262144 net.inet.tcp.recvspace=262144 net.inet.udp.recvspace=262144 kern.ipc.maxsockbuf=16777216 kern.ipc.nmbclusters=32768 net.inet.tcp.delayed_ack=1 net.inet.tcp.delacktime=100 net.inet.tcp.slowstart_flightsize=179 net.inet.tcp.inflight.enable=1 net.inet.tcp.inflight.min=6144 # Reduce the cache size of slow start connection net.inet.tcp.hostcache.expire=1 Our network admin also claim that they see quite a lot of network up and down from their cisco switch log while I cannot find any up down message inside the dmesg. Have further checked the netstat -s but dont have concrete idea. tcp: 133695291 packets sent 39408539 data packets (3358837321 bytes) 61868 data packets (89472844 bytes) retransmitted 24 data packets unnecessarily retransmitted 0 resends initiated by MTU discovery 50756141 ack-only packets (2148 delayed) 0 URG only packets 0 window probe packets 4372385 window update packets 39781869 control packets 134898031 packets received 72339403 acks (for 3357601899 bytes) 190712 duplicate acks 0 acks for unsent data 59339201 packets (3647021974 bytes) received in-sequence 114 completely duplicate packets (135202 bytes) 27 old duplicate packets 0 packets with some dup. data (0 bytes duped) 42090 out-of-order packets (60817889 bytes) 0 packets (0 bytes) of data after window 0 window probes 3953896 window update packets 64181 packets received after close 0 discarded for bad checksums 0 discarded for bad header offset fields 0 discarded because packet too short 45192 discarded due to memory problems 19945391 connection requests 1323420 connection accepts 0 bad connection attempts 0 listen queue overflows 0 ignored RSTs in the windows 21133581 connections established (including accepts) 21268724 connections closed (including 32737 drops) 207874 connections updated cached RTT on close 207874 connections updated cached RTT variance on close 132439 connections updated cached ssthresh on close 42392 embryonic connections dropped 72339338 segments updated rtt (of 69477829 attempts) 390871 retransmit timeouts 0 connections dropped by rexmit timeout 0 persist timeouts 0 connections dropped by persist timeout 0 Connections (fin_wait_2) dropped because of timeout 13990 keepalive timeouts 2 keepalive probes sent 13988 connections dropped by keepalive 173044 correct ACK header predictions 36947371 correct data packet header predictions 1323420 syncache entries added 0 retransmitted 0 dupsyn 0 dropped 1323420 completed 0 bucket overflow 0 cache overflow 0 reset 0 stale 0 aborted 0 badack 0 unreach 0 zone failures 1323420 cookies sent 0 cookies received 1864 SACK recovery episodes 18005 segment rexmits in SACK recovery episodes 26066896 byte rexmits in SACK recovery episodes 147327 SACK options (SACK blocks) received 87473 SACK options (SACK blocks) sent 0 SACK scoreboard overflow 0 packets with ECN CE bit set 0 packets with ECN ECT(0) bit set 0 packets with ECN ECT(1) bit set 0 successful ECN handshakes 0 times ECN reduced the congestion window udp: 5141258 datagrams received 0 with incomplete header 0 with bad data length field 0 with bad checksum 1 with no checksum 0 dropped due to no socket 129616 broadcast/multicast datagrams undelivered 0 dropped due to full socket buffers 0 not for hashed pcb 5011642 delivered 5016050 datagrams output 0 times multicast source filter matched sctp: 0 input packets 0 datagrams 0 packets that had data 0 input SACK chunks 0 input DATA chunks 0 duplicate DATA chunks 0 input HB chunks 0 HB-ACK chunks 0 input ECNE chunks 0 input AUTH chunks 0 chunks missing AUTH 0 invalid HMAC ids received 0 invalid secret ids received 0 auth failed 0 fast path receives all one chunk 0 fast path multi-part data 0 output packets 0 output SACKs 0 output DATA chunks 0 retransmitted DATA chunks 0 fast retransmitted DATA chunks 0 FR's that happened more than once to same chunk 0 intput HB chunks 0 output ECNE chunks 0 output AUTH chunks 0 ip_output error counter Packet drop statistics: 0 from middle box 0 from end host 0 with data 0 non-data, non-endhost 0 non-endhost, bandwidth rep only 0 not enough for chunk header 0 not enough data to confirm 0 where process_chunk_drop said break 0 failed to find TSN 0 attempt reverse TSN lookup 0 e-host confirms zero-rwnd 0 midbox confirms no space 0 data did not match TSN 0 TSN's marked for Fast Retran Timeouts: 0 iterator timers fired 0 T3 data time outs 0 window probe (T3) timers fired 0 INIT timers fired 0 sack timers fired 0 shutdown timers fired 0 heartbeat timers fired 0 a cookie timeout fired 0 an endpoint changed its cookiesecret 0 PMTU timers fired 0 shutdown ack timers fired 0 shutdown guard timers fired 0 stream reset timers fired 0 early FR timers fired 0 an asconf timer fired 0 auto close timer fired 0 asoc free timers expired 0 inp free timers expired 0 packet shorter than header 0 checksum error 0 no endpoint for port 0 bad v-tag 0 bad SID 0 no memory 0 number of multiple FR in a RTT window 0 RFC813 allowed sending 0 RFC813 does not allow sending 0 times max burst prohibited sending 0 look ahead tells us no memory in interface 0 numbers of window probes sent 0 times an output error to clamp down on next user send 0 times sctp_senderrors were caused from a user 0 number of in data drops due to chunk limit reached 0 number of in data drops due to rwnd limit reached 0 times a ECN reduced the cwnd 0 used express lookup via vtag 0 collision in express lookup 0 times the sender ran dry of user data on primary 0 same for above 0 sacks the slow way 0 window update only sacks sent 0 sends with sinfo_flags !=0 0 unordered sends 0 sends with EOF flag set 0 sends with ABORT flag set 0 times protocol drain called 0 times we did a protocol drain 0 times recv was called with peek 0 cached chunks used 0 cached stream oq's used 0 unread messages abandonded by close 0 send burst avoidance, already max burst inflight to net 0 send cwnd full avoidance, already max burst inflight to net 0 number of map array over-runs via fwd-tsn's ip: 137814085 total packets received 0 bad header checksums 0 with size smaller than minimum 0 with data size < data length 0 with ip length > max ip packet size 0 with header length < data size 0 with data length < header length 0 with bad options 0 with incorrect version number 1200 fragments received 0 fragments dropped (dup or out of space) 0 fragments dropped after timeout 300 packets reassembled ok 137813009 packets for this host 530 packets for unknown/unsupported protocol 0 packets forwarded (0 packets fast forwarded) 61 packets not forwardable 0 packets received for unknown multicast group 0 redirects sent 137234598 packets sent from this host 0 packets sent with fabricated ip header 685307 output packets dropped due to no bufs, etc. 52 output packets discarded due to no route 300 output datagrams fragmented 1200 fragments created 0 datagrams that can't be fragmented 0 tunneling packets that can't find gif 0 datagrams with bad address in header icmp: 0 calls to icmp_error 0 errors not generated in response to an icmp message Output histogram: echo reply: 305 0 messages with bad code fields 0 messages less than the minimum length 0 messages with bad checksum 0 messages with bad length 0 multicast echo requests ignored 0 multicast timestamp requests ignored Input histogram: destination unreachable: 530 echo: 305 305 message responses generated 0 invalid return addresses 0 no return routes ICMP address mask responses are disabled igmp: 0 messages received 0 messages received with too few bytes 0 messages received with wrong TTL 0 messages received with bad checksum 0 V1/V2 membership queries received 0 V3 membership queries received 0 membership queries received with invalid field(s) 0 general queries received 0 group queries received 0 group-source queries received 0 group-source queries dropped 0 membership reports received 0 membership reports received with invalid field(s) 0 membership reports received for groups to which we belong 0 V3 reports received without Router Alert 0 membership reports sent arp: 376748 ARP requests sent 3207 ARP replies sent 245245 ARP requests received 80845 ARP replies received 326090 ARP packets received 267712 total packets dropped due to no ARP entry 108876 ARP entrys timed out 0 Duplicate IPs seen ip6: 2226633 total packets received 0 with size smaller than minimum 0 with data size < data length 0 with bad options 0 with incorrect version number 0 fragments received 0 fragments dropped (dup or out of space) 0 fragments dropped after timeout 0 fragments that exceeded limit 0 packets reassembled ok 2226633 packets for this host 0 packets forwarded 0 packets not forwardable 0 redirects sent 2226633 packets sent from this host 0 packets sent with fabricated ip header 0 output packets dropped due to no bufs, etc. 8 output packets discarded due to no route 0 output datagrams fragmented 0 fragments created 0 datagrams that can't be fragmented 0 packets that violated scope rules 0 multicast packets which we don't join Input histogram: UDP: 2226633 Mbuf statistics: 962679 one mbuf 1263954 one ext mbuf 0 two or more ext mbuf 0 packets whose headers are not continuous 0 tunneling packets that can't find gif 0 packets discarded because of too many headers 0 failures of source address selection Source addresses selection rule applied: icmp6: 0 calls to icmp6_error 0 errors not generated in response to an icmp6 message 0 errors not generated because of rate limitation 0 messages with bad code fields 0 messages < minimum length 0 bad checksums 0 messages with bad length Histogram of error messages to be generated: 0 no route 0 administratively prohibited 0 beyond scope 0 address unreachable 0 port unreachable 0 packet too big 0 time exceed transit 0 time exceed reassembly 0 erroneous header field 0 unrecognized next header 0 unrecognized option 0 redirect 0 unknown 0 message responses generated 0 messages with too many ND options 0 messages with bad ND options 0 bad neighbor solicitation messages 0 bad neighbor advertisement messages 0 bad router solicitation messages 0 bad router advertisement messages 0 bad redirect messages 0 path MTU changes rip6: 0 messages received 0 checksum calculations on inbound 0 messages with bad checksum 0 messages dropped due to no socket 0 multicast messages dropped due to no socket 0 messages dropped due to full socket buffers 0 delivered 0 datagrams output netstat -m 516/5124/5640 mbufs in use (current/cache/total) 512/1634/2146/32768 mbuf clusters in use (current/cache/total/max) 512/1536 mbuf+clusters out of packet secondary zone in use (current/cache) 0/1303/1303/12800 4k (page size) jumbo clusters in use (current/cache/total/max) 0/0/0/6400 9k jumbo clusters in use (current/cache/total/max) 0/0/0/3200 16k jumbo clusters in use (current/cache/total/max) 1153K/9761K/10914K bytes allocated to network (current/cache/total) 0/0/0 requests for mbufs denied (mbufs/clusters/mbuf+clusters) 0/0/0 requests for jumbo clusters denied (4k/9k/16k) 0/8/6656 sfbufs in use (current/peak/max) 0 requests for sfbufs denied 0 requests for sfbufs delayed 0 requests for I/O initiated by sendfile 0 calls to protocol drain routines Anyone got an idea what might be the possible cause?

  Read the article

• SOA Suite 11g Asynchronous Testing with soapUI

  - by Greg Mally

  Overview The Enterprise Manager test harness that comes bundled with SOA Suite 11g is a great tool for doing smoke tests and some minor load testing. When a more robust testing tool is needed, often times soapUI is leveraged for many reasons ranging from ease of use to cost effective. However, when you want to start doing some more complex testing other than synchronous web services with static content, then the free version of soapUI becomes a bit more challenging. In this blog I will show you how to test asynchronous web services with soapUI free edition. The following assumes that you have a working knowledge of soapUI and will not go into concepts like setting up a project etc. For the basics, please review the documentation for soapUI: http://www.soapui.org/Getting-Started/ Asynchronous Web Service Testing in soapUI When invoking an asynchronous web service, the caller must provide a callback for the response. Since our testing will originate from soapUI, then it is only natural that soapUI would provide the callback mechanism. This mechanism in soapUI is called a MockService. In a nutshell, a soapUI MockService is a simulation of a Web Service (aka, a process listening on a port). We will go through the steps in setting up the MockService for a simple asynchronous BPEL process. After creating your soapUI project based on an asynchronous BPEL process, you will see something like the following: Notice that soapUI created an interface for both the request and the response (i.e., callback). The interface that was created for the callback will be used to create the MockService. Right-click on the callback interface and select the Generate MockService menu item: You will be presented with the Generate MockService dialogue where we will tweak the Path and possibly the port (depends upon what ports are available on the machine where soapUI will be running). We will adjust the Path to include the operation name (append /processResponse in this example) and the port of 8088 is fine: Once the MockService is created, you should have something like the following in soapUI: This window acts as a console/view into the callback process. When the play button is pressed (green triangle in the upper left-hand corner), soapUI will start a process running on the configured Port that will accept web service invocations on the configured Path: At this point we are “almost” ready to try out the asynchronous test. But first we must provide the web service addressing (WS-A) configuration on the request message. We will edit the message for the request interface that was generated when the project was created (SimpleAsyncBPELProcessBinding > process > Request 1 in this example). At the bottom of the request message editor you will find the WS-A configuration by left-clicking on the WS-A label: Here we will setup WS-A by changing the default values to: Must understand: TRUE Add default wsa:Action: Add default wsa:Action (checked) Reply to: ${host where soapUI is running}:${MockService Port}${MockService Path} … in this example: http://192.168.1.181:8088/mockSimpleAsyncBPELProcessCallbackBinding/processResponse We now are ready to run the asynchronous test from soapUI free edition. Make sure that the MockService you created is running and then push the play button for the request (green triangle in the upper left-hand corner of the request editor). If everything is configured correctly, you should see the response show up in the MockService window: To view the response message/payload, just double-click on a response message in the Message Log window of the MockService: At this point you can now expand the project to include a Test Suite for some load balance tests etc. This same topic has been covered in various detail on other sites/blogs, but I wanted to simplify and detail how this is done in the context of SOA Suite 11g. It also serves as a nice introduction to another blog of mine: SOA Suite 11g Dynamic Payload Testing with soapUI Free Edition.

  Read the article

• How to Install Oracle Software on Remote Linux Server

  - by James Taylor

  It is becoming more common these days to install Oracle software on remote Linux servers. This issue has always existed but was generally resolved either by silent installs or by someone physically going to the server to install the software. This is becoming more difficult with the popular virtualisation and cloud deployment strategies. This post provides the steps involved to install Oracle Software using the GUI interface on a remote Linux server. There are many ways to achieve this, the way I resolve this issue is via Virtual Network Computing (VNC) as it is shipped with RedHat and OEL out of the box. For this post I’m using OEL 5 deployed on a OVM guest. If not already done so download and install a client version of VNC so you can connect to the server. There are many out there, for the purpose of this post I use UltraVNC. You can download a free version from http://www.uvnc.com/download/index.html By default VNC Server is installed in your RedHat and OEL OS, but it is not configured. The way VNC works is when started it creates a client instance for the user and binds it to a specific port. So if have an account on the Linux box you can setup a VNC Server session for that user, you don’t need to be root. For the purpose of this document I’m going to use oracle as the user to setup a VNC Session as this is the user I want use to install the software. However to start the VNC Service you must be root. As the root user run the following command: service vncserver start Starting VNC server: no displays configured                [  OK  ] Login to the Linux box as the user  you wan to install the Oracle software [oracle@lisa ~]$ Run the command to create a new VNC server instance for the oracle user: vncserver You will be ask to supply password information. This is what you will enter when connecting from your desktop client. This password is also independent of the actual Linux user password. The VNC Server is acting as a proxy to this instance. You will require a password to access your desktops. Password: Verify: xauth:  creating new authority file /home/oracle/.Xauthority New 'lisa.nz.oracle.com:1 (oracle)' desktop is lisa.nz.oracle.com:1 Creating default startup script /home/oracle/.vnc/xstartup Starting applications specified in /home/oracle/.vnc/xstartup Log file is /home/oracle/.vnc/lisa.nz.oracle.com:1.log As you can see a new instance lisa.nz.oracle.com:1 has been created. If you were to run the vncserver command again another instance lisa.nz.oracle.com:2 will be created. If you are going through a firewall you will need to ensure that the port 5901 (port 1) is open between your client desktop and the Linux Server. Depending on the options chosen at install time a firewall could be in place. The simplest way to disable this is using the command. You will need to be root. service iptables stop This will stop the firewall while you install. If you just want to add a port to the accepted lists use the firewall UI. You will need to be root. system-config-security-level Now you are ready to connect to the server via the VNC. Using the software installed in step one start the VNC Client. You should be prompted for the server and port. If connectivity is established, you will be prompted for the password entered in step 5. You should now be presented with a terminal screen ready to install software Go to the location of the oracle install software and start the Oracle Universal Installer

  Read the article

• WSAECONNRESET (10054) error using WebDrive to map to a Subversion/Apache WebDAV share

  - by Dylan Beattie

  Hello, I'm using WebDrive to map a drive letter to a WebDAV share running on Subversion with the SVNAutoversioning flag enabled. The Subversion server is running CollabNet Subversion Edge with LDAP authentication. When trying to connect using WebDrive, I get: Connecting to site myserver Connecting to http://myserver/webdrive/ Resolving url myserver to an IP address Url resolved to IP address 192.168.0.12 Connecting to 192.168.0.12 on port 80 Connected successfully to the server on port 80 Testing directory listing ... Connecting to 192.168.0.12 on port 80 Connected successfully to the server on port 80 Unable to connect to server, error information below Error: Socket receive failure (4507) Operation: Connecting to server Winsock Error: WSAECONNRESET (10054) The httpd.conf file running on the server contains the following section: <Location /webdrive/> DAV svn SVNParentPath "C:\Program Files\Subversion\data\repositories" SVNReposName "My Subversion WebDrive" AuthzSVNAccessFile "C:\Program Files\Subversion\data/conf/svn_access_file" SVNListParentPath On Allow from all AuthType Basic AuthName "My Subversion Repository" AuthBasicProvider csvn-file-users ldap-users Require valid-user ModMimeUsePathInfo on SVNAutoversioning on </Location> and in the Apache error_yyyy_mm_dd.log file on the server, I'm seeing this when I try to connect via WebDAV: [Mon Jan 10 14:53:22 2011] [debug] mod_authnz_ldap.c(379): [client 192.168.0.50] [5572] auth_ldap authenticate: using URL ldap://mydc/dc=mydomain,dc=com?sAMAccountName?sub [Mon Jan 10 14:53:22 2011] [debug] mod_authnz_ldap.c(484): [client 192.168.0.50] [5572] auth_ldap authenticate: accepting dylan.beattie [Mon Jan 10 14:53:22 2011] [info] [client 192.168.0.50] Access granted: 'dylan.beattie' OPTIONS webdrive:/ [Mon Jan 10 14:53:22 2011] [debug] mod_authnz_ldap.c(379): [client 192.168.0.50] [5572] auth_ldap authenticate: using URL ldap://mydc/dc=mydomain,dc=com?sAMAccountName?sub [Mon Jan 10 14:53:22 2011] [debug] mod_authnz_ldap.c(484): [client 192.168.0.50] [5572] auth_ldap authenticate: accepting dylan.beattie [Mon Jan 10 14:53:22 2011] [info] [client 192.168.0.50] Access granted: 'dylan.beattie' PROPFIND webdrive:/ [Mon Jan 10 14:53:25 2011] [notice] Parent: child process exited with status 3221225477 -- Restarting. [Mon Jan 10 14:53:25 2011] [debug] util_ldap.c(1990): LDAP merging Shared Cache conf: shm=0xcd0f18 rmm=0xcd0f48 for VHOST: myserver.mydomain.com [Mon Jan 10 14:53:25 2011] [debug] util_ldap.c(1990): LDAP merging Shared Cache conf: shm=0xcd0f18 rmm=0xcd0f48 for VHOST: myserver.mydomain.com [Mon Jan 10 14:53:25 2011] [info] APR LDAP: Built with Microsoft Corporation. LDAP SDK [Mon Jan 10 14:53:25 2011] [info] LDAP: SSL support unavailable: LDAP: CA certificates cannot be set using this method, as they are stored in the registry instead. [Mon Jan 10 14:53:25 2011] [notice] Apache/2.2.16 (Win32) DAV/2 SVN/1.6.13 configured -- resuming normal operations [Mon Jan 10 14:53:25 2011] [notice] Server built: Oct 4 2010 19:55:36 [Mon Jan 10 14:53:25 2011] [notice] Parent: Created child process 4368 [Mon Jan 10 14:53:25 2011] [debug] mpm_winnt.c(487): Parent: Sent the scoreboard to the child [Mon Jan 10 14:53:25 2011] [debug] util_ldap.c(1990): LDAP merging Shared Cache conf: shm=0xca2bb0 rmm=0xca2be0 for VHOST: myserver.mydomain.com [Mon Jan 10 14:53:25 2011] [debug] util_ldap.c(1990): LDAP merging Shared Cache conf: shm=0xca2bb0 rmm=0xca2be0 for VHOST: myserver.mydomain.com [Mon Jan 10 14:53:25 2011] [info] APR LDAP: Built with Microsoft Corporation. LDAP SDK [Mon Jan 10 14:53:25 2011] [info] LDAP: SSL support unavailable: LDAP: CA certificates cannot be set using this method, as they are stored in the registry instead. [Mon Jan 10 14:53:25 2011] [error] python_init: Python version mismatch, expected '2.5', found '2.5.4'. [Mon Jan 10 14:53:25 2011] [error] python_init: Python executable found 'C:\\Program Files\\Subversion\\bin\\httpd.exe'. [Mon Jan 10 14:53:25 2011] [error] python_init: Python path being used 'C:\\Program Files\\Subversion\\Python25\\python25.zip;C:\\Program Files\\Subversion\\Python25\\\\DLLs;C:\\Program Files\\Subversion\\Python25\\\\lib;C:\\Program Files\\Subversion\\Python25\\\\lib\\plat-win;C:\\Program Files\\Subversion\\Python25\\\\lib\\lib-tk;C:\\Program Files\\Subversion\\bin'. [Mon Jan 10 14:53:25 2011] [notice] mod_python: Creating 8 session mutexes based on 0 max processes and 64 max threads. [Mon Jan 10 14:53:25 2011] [notice] Child 4368: Child process is running [Mon Jan 10 14:53:25 2011] [debug] mpm_winnt.c(408): Child 4368: Retrieved our scoreboard from the parent. [Mon Jan 10 14:53:25 2011] [info] Parent: Duplicating socket 288 and sending it to child process 4368 [Mon Jan 10 14:53:25 2011] [info] Parent: Duplicating socket 276 and sending it to child process 4368 [Mon Jan 10 14:53:25 2011] [debug] mpm_winnt.c(564): Child 4368: retrieved 2 listeners from parent [Mon Jan 10 14:53:25 2011] [notice] Child 4368: Acquired the start mutex. [Mon Jan 10 14:53:25 2011] [notice] Child 4368: Starting 64 worker threads. [Mon Jan 10 14:53:25 2011] [debug] mpm_winnt.c(605): Parent: Sent 2 listeners to child 4368 [Mon Jan 10 14:53:25 2011] [notice] Child 4368: Starting thread to listen on port 49159. [Mon Jan 10 14:53:25 2011] [notice] Child 4368: Starting thread to listen on port 80. [Mon Jan 10 14:53:25 2011] [debug] mod_authnz_ldap.c(379): [client 192.168.0.50] [4368] auth_ldap authenticate: using URL ldap://mydc/dc=mydomain,dc=com?sAMAccountName?sub [Mon Jan 10 14:53:25 2011] [debug] mod_authnz_ldap.c(484): [client 192.168.0.50] [4368] auth_ldap authenticate: accepting dylan.beattie [Mon Jan 10 14:53:25 2011] [info] [client 192.168.0.50] Access granted: 'dylan.beattie' PROPFIND webdrive:/ [Mon Jan 10 14:53:28 2011] [notice] Parent: child process exited with status 3221225477 -- Restarting. [Mon Jan 10 14:53:28 2011] [debug] util_ldap.c(1990): LDAP merging Shared Cache conf: shm=0xcd4f90 rmm=0xcd4fc0 for VHOST: myserver.mydomain.com [Mon Jan 10 14:53:28 2011] [debug] util_ldap.c(1990): LDAP merging Shared Cache conf: shm=0xcd4f90 rmm=0xcd4fc0 for VHOST: myserver.mydomain.com [Mon Jan 10 14:53:28 2011] [info] APR LDAP: Built with Microsoft Corporation. LDAP SDK [Mon Jan 10 14:53:28 2011] [info] LDAP: SSL support unavailable: LDAP: CA certificates cannot be set using this method, as they are stored in the registry instead. [Mon Jan 10 14:53:28 2011] [notice] Apache/2.2.16 (Win32) DAV/2 SVN/1.6.13 configured -- resuming normal operations [Mon Jan 10 14:53:28 2011] [notice] Server built: Oct 4 2010 19:55:36 [Mon Jan 10 14:53:28 2011] [notice] Parent: Created child process 5440 [Mon Jan 10 14:53:28 2011] [debug] mpm_winnt.c(487): Parent: Sent the scoreboard to the child [Mon Jan 10 14:53:28 2011] [debug] util_ldap.c(1990): LDAP merging Shared Cache conf: shm=0xda2bb0 rmm=0xda2be0 for VHOST: myserver.mydomain.com [Mon Jan 10 14:53:28 2011] [debug] util_ldap.c(1990): LDAP merging Shared Cache conf: shm=0xda2bb0 rmm=0xda2be0 for VHOST: myserver.mydomain.com [Mon Jan 10 14:53:28 2011] [info] APR LDAP: Built with Microsoft Corporation. LDAP SDK [Mon Jan 10 14:53:28 2011] [info] LDAP: SSL support unavailable: LDAP: CA certificates cannot be set using this method, as they are stored in the registry instead. [Mon Jan 10 14:53:28 2011] [error] python_init: Python version mismatch, expected '2.5', found '2.5.4'. [Mon Jan 10 14:53:28 2011] [error] python_init: Python executable found 'C:\\Program Files\\Subversion\\bin\\httpd.exe'. [Mon Jan 10 14:53:28 2011] [error] python_init: Python path being used 'C:\\Program Files\\Subversion\\Python25\\python25.zip;C:\\Program Files\\Subversion\\Python25\\\\DLLs;C:\\Program Files\\Subversion\\Python25\\\\lib;C:\\Program Files\\Subversion\\Python25\\\\lib\\plat-win;C:\\Program Files\\Subversion\\Python25\\\\lib\\lib-tk;C:\\Program Files\\Subversion\\bin'. [Mon Jan 10 14:53:28 2011] [notice] mod_python: Creating 8 session mutexes based on 0 max processes and 64 max threads. [Mon Jan 10 14:53:28 2011] [notice] Child 5440: Child process is running [Mon Jan 10 14:53:28 2011] [debug] mpm_winnt.c(408): Child 5440: Retrieved our scoreboard from the parent. [Mon Jan 10 14:53:28 2011] [info] Parent: Duplicating socket 288 and sending it to child process 5440 [Mon Jan 10 14:53:28 2011] [info] Parent: Duplicating socket 276 and sending it to child process 5440 [Mon Jan 10 14:53:28 2011] [debug] mpm_winnt.c(564): Child 5440: retrieved 2 listeners from parent [Mon Jan 10 14:53:28 2011] [notice] Child 5440: Acquired the start mutex. [Mon Jan 10 14:53:28 2011] [notice] Child 5440: Starting 64 worker threads. [Mon Jan 10 14:53:28 2011] [debug] mpm_winnt.c(605): Parent: Sent 2 listeners to child 5440 [Mon Jan 10 14:53:28 2011] [notice] Child 5440: Starting thread to listen on port 49159. [Mon Jan 10 14:53:28 2011] [notice] Child 5440: Starting thread to listen on port 80. Browsing http://myserver/webdrive/ from a web browser is working fine, and I have a similar set-up working perfectly on a different SVN server that isn't running Collabnet but has had Subversion and Apache installed and configured separately. Any ideas? The python version error might be red herring - I've seen it in a couple of places in the log files and in other scenarios it doesn't appear to be breaking anything...

  Read the article

• OWA, Outlook Anywhere, RPCPing Inconsistencies

  - by pk.

  I'm troubleshooting an Outlook Anywhere issue with a new Exchange 2010 server. The server in question, MS2010, is behind a SonicWALL NSA 2400 device and works wonderfully except for Outlook Anywhere. Outlook Anywhere works internally and I've verified (through Ctrl-Right Click --> Connection Status) that I'm able to connect to MS2010 over HTTPS. When trying to connect to the server using HTTPS from outside the firewall, I'm unable to do so. A Wireshark trace shows 30 or so successful HTTPS packet transmissions, and then it fails with 3 straight transmissions to a destination port of 135. I have no idea why my computer is attempting to access anything on port 135 since I've setup my profile to use HTTPS on both slow and fast connections. I'm 99% certain that the firewall is configured correctly. I run Outlook Web Access (also HTTPS) on the same server and there are no issues with access. EDIT: My Autodiscover settings are correct (as far as I can tell). My server passes the Outlook Anywhere and Autodiscover tests at https://www.testexchangeconnectivity.com/. I've been using the RPCPing utility to troubleshoot and have come across the following results: Internally- >rpcping -t ncacn_http -s mail.mydomain.com -o RpcProxy=mail.mydomain.com -P "pk,mydomain,*" -I "pk,mydomain,*" -H 1 -u 10 -a connect -F 3 -v 3 -E -R none RPCPing v2.12. Copyright (C) Microsoft Corporation, 2002 OS Version is: 6.1, Service Pack 1 RPCPinging proxy server mail.mydomain.com with Echo Request Packet Sending ping to server Response from server received: 200 Pinging successfully completed in 93 ms Externally- >rpcping -t ncacn_http -s mail.mydomain.com -o RpcProxy=mail.mydomain.com -P "pk,mydomain,*" -I "pk,mydomain,*" -H 1 -u 10 -a connect -F 3 -v 3 -E -R none RPCPing v6.0. Copyright (C) Microsoft Corporation, 2002-2006 Enter password for RPC/HTTP proxy: RPCPing set Activity ID: {fc8411ba-2987-4175-b37b-801dc69d5ff9} RPCPinging proxy server mail.mydomain.com with Echo Request Packet Setting autologon policy to high WinHttpSetCredentials for target server called Error 87 : The parameter is incorrect. returned in WinHttpSetCredentials Ping failed What should I be checking in order to troubleshoot my Outlook Anywhere issues? I'm using Windows 7 SP1 for internal and external access. EDIT: Autodiscover.xml content <?xml version="1.0"?> <Autodiscover xmlns:xsd="http://www.w3.org/2001/XMLSchema" xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance" xmlns="http://schemas.microsoft.com/exchange/autodiscover/responseschema/2006"> <Response xmlns="http://schemas.microsoft.com/exchange/autodiscover/outlook/responseschema/2006a"> <User> <DisplayName>John Doe</DisplayName> <LegacyDN>/o=MYDOMAIN/ou=Exchange Administrative Group (FYDIBOHF23SPDLT)/cn=Recipients/cn=pk</LegacyDN> <DeploymentId>d35170cc-f3a7-42c5-9427-1f554a469126</DeploymentId> </User> <Account> <AccountType>email</AccountType> <Action>settings</Action> <Protocol> <Type>EXCH</Type> <Server>MS2010.MYDOMAIN.local</Server> <ServerDN>/o=MYDOMAIN/ou=Exchange Administrative Group (FYDIBOHF23SPDLT)/cn=Configuration/cn=Servers/cn=MS2010</ServerDN> <ServerVersion>738180DA</ServerVersion> <MdbDN>/o=MYDOMAIN/ou=Exchange Administrative Group (FYDIBOHF23SPDLT)/cn=Configuration/cn=Servers/cn=MS2010/cn=Microsoft Private MDB</MdbDN> <ASUrl>https://MS2010.MYDOMAIN.local/EWS/Exchange.asmx</ASUrl> <OOFUrl>https://MS2010.MYDOMAIN.local/EWS/Exchange.asmx</OOFUrl> <OABUrl>http://MS2010.MYDOMAIN.local/OAB/2c34c9f5-5521-4c8c-b684-538df815052a/</OABUrl> <UMUrl>https://MS2010.MYDOMAIN.local/EWS/UM2007Legacy.asmx</UMUrl> <Port>0</Port> <DirectoryPort>0</DirectoryPort> <ReferralPort>0</ReferralPort> <PublicFolderServer>MS2007.MYDOMAIN.local</PublicFolderServer> <AD>dc1.MYDOMAIN.local</AD> <EwsUrl>https://MS2010.MYDOMAIN.local/EWS/Exchange.asmx</EwsUrl> <EcpUrl>https://MS2010.MYDOMAIN.local/ecp/</EcpUrl> <EcpUrl-um>?p=customize/voicemail.aspx&amp;exsvurl=1</EcpUrl-um> <EcpUrl-aggr>?p=personalsettings/EmailSubscriptions.slab&amp;exsvurl=1</EcpUrl-aggr> <EcpUrl-mt>PersonalSettings/DeliveryReport.aspx?exsvurl=1&amp;IsOWA=&lt;IsOWA&gt;&amp;MsgID=&lt;MsgID&gt;&amp;Mbx=&lt;Mbx&gt;</EcpUrl-mt> <EcpUrl-ret>?p=organize/retentionpolicytags.slab&amp;exsvurl=1</EcpUrl-ret> <EcpUrl-sms>?p=sms/textmessaging.slab&amp;exsvurl=1</EcpUrl-sms> </Protocol> <Protocol> <Type>EXPR</Type> <Server>mail.mycompany.com</Server> <ASUrl>https://mail.mycompany.com/ews/exchange.asmx</ASUrl> <OOFUrl>https://mail.mycompany.com/ews/exchange.asmx</OOFUrl> <OABUrl>https://mail.mycompany.com/OAB/2c34c9f5-5521-4c8c-b684-538df815052a/</OABUrl> <UMUrl>https://mail.mycompany.com/ews/UM2007Legacy.asmx</UMUrl> <Port>0</Port> <DirectoryPort>0</DirectoryPort> <ReferralPort>0</ReferralPort> <SSL>On</SSL> <AuthPackage>Basic</AuthPackage> <CertPrincipalName>msstd:mail.mycompany.com</CertPrincipalName> <EwsUrl>https://mail.mycompany.com/ews/exchange.asmx</EwsUrl> <EcpUrl>https://mail.mycompany.com/owa/</EcpUrl> <EcpUrl-um>?p=customize/voicemail.aspx&amp;exsvurl=1</EcpUrl-um> <EcpUrl-aggr>?p=personalsettings/EmailSubscriptions.slab&amp;exsvurl=1</EcpUrl-aggr> <EcpUrl-mt>PersonalSettings/DeliveryReport.aspx?exsvurl=1&amp;IsOWA=&lt;IsOWA&gt;&amp;MsgID=&lt;MsgID&gt;&amp;Mbx=&lt;Mbx&gt;</EcpUrl-mt> <EcpUrl-ret>?p=organize/retentionpolicytags.slab&amp;exsvurl=1</EcpUrl-ret> <EcpUrl-sms>?p=sms/textmessaging.slab&amp;exsvurl=1</EcpUrl-sms> </Protocol> <Protocol> <Type>WEB</Type> <Port>0</Port> <DirectoryPort>0</DirectoryPort> <ReferralPort>0</ReferralPort> <Internal> <OWAUrl AuthenticationMethod="Basic, Fba">https://MS2010.MYDOMAIN.local/owa/</OWAUrl> <Protocol> <Type>EXCH</Type> <ASUrl>https://MS2010.MYDOMAIN.local/EWS/Exchange.asmx</ASUrl> </Protocol> </Internal> <External> <OWAUrl AuthenticationMethod="Fba">https://mail.mycompany.com/owa/</OWAUrl> <Protocol> <Type>EXPR</Type> <ASUrl>https://mail.mycompany.com/ews/exchange.asmx</ASUrl> </Protocol> </External> </Protocol> </Account> </Response> </Autodiscover>

  Read the article

• how do i fix this: the networking and wireless are enabled. but list of networks under wireless networks not available

  - by Ayesha Ahmad

  i started working with ubuntu 11.10 last year. i upgraded to 12.04 a week back. since then i have had all sorts of problems with network connection. first had to install the new driver. the hardware switch somehow got disabled then the above problem arrived. even tho the options are all enabled, the OS is not able to detect scan available network connections. also i have to bring to notice that once in a while it does get connected, can not explain how it happens. I want to fix this problem once and for all. please help. ifconfig: eth0 Link encap:Ethernet HWaddr f0:4d:a2:51:b3:c8 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:44 eth1 Link encap:Ethernet HWaddr 1c:65:9d:67:d5:e1 inet6 addr: fe80::1e65:9dff:fe67:d5e1/64 Scope:Link UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:170 TX packets:0 errors:27 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:17 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:344 errors:0 dropped:0 overruns:0 frame:0 TX packets:344 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:20336 (20.3 KB) TX bytes:20336 (20.3 KB) lshw -c network *-network description: Wireless interface product: BCM4313 802.11b/g/n Wireless LAN Controller vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:03:00.0 logical name: eth1 version: 01 serial: 1c:65:9d:67:d5:e1 width: 64 bits clock: 33MHz capabilities: bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=wl0 driverversion=5.100.82.38 latency=0 multicast=yes wireless=IEEE 802.11 resources: irq:17 memory:f0500000-f0503fff *-network description: Ethernet interface product: AR8152 v1.1 Fast Ethernet vendor: Atheros Communications Inc. physical id: 0 bus info: pci@0000:04:00.0 logical name: eth0 version: c1 serial: f0:4d:a2:51:b3:c8 capacity: 100Mbit/s width: 64 bits clock: 33MHz capabilities: bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=atl1c driverversion=1.0.1.0-NAPI firmware=N/A latency=0 multicast=yes port=twisted pair resources: irq:44 memory:f0400000-f043ffff ioport:2000(size=128) iwconfig lo no wireless extensions. eth1 IEEE 802.11 Access Point: Not-Associated Link Quality:5 Signal level:0 Noise level:196 Rx invalid nwid:0 invalid crypt:0 invalid misc:0 eth0 no wireless extensions. lspci 00:00.0 Host bridge: Intel Corporation Core Processor DRAM Controller (rev 18) 00:02.0 VGA compatible controller: Intel Corporation Core Processor Integrated Graphics Controller (rev 18) 00:16.0 Communication controller: Intel Corporation 5 Series/3400 Series Chipset HECI Controller (rev 06) 00:1a.0 USB controller: Intel Corporation 5 Series/3400 Series Chipset USB2 Enhanced Host Controller (rev 06) 00:1b.0 Audio device: Intel Corporation 5 Series/3400 Series Chipset High Definition Audio (rev 06) 00:1c.0 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 1 (rev 06) 00:1c.1 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 2 (rev 06) 00:1c.5 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 6 (rev 06) 00:1d.0 USB controller: Intel Corporation 5 Series/3400 Series Chipset USB2 Enhanced Host Controller (rev 06) 00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev a6) 00:1f.0 ISA bridge: Intel Corporation Mobile 5 Series Chipset LPC Interface Controller (rev 06) 00:1f.2 SATA controller: Intel Corporation 5 Series/3400 Series Chipset 6 port SATA AHCI Controller (rev 06) 00:1f.3 SMBus: Intel Corporation 5 Series/3400 Series Chipset SMBus Controller (rev 06) 00:1f.6 Signal processing controller: Intel Corporation 5 Series/3400 Series Chipset Thermal Subsystem (rev 06) 03:00.0 Network controller: Broadcom Corporation BCM4313 802.11b/g/n Wireless LAN Controller (rev 01) 04:00.0 Ethernet controller: Atheros Communications Inc. AR8152 v1.1 Fast Ethernet (rev c1) ff:00.0 Host bridge: Intel Corporation Core Processor QuickPath Architecture Generic Non-core Registers (rev 05) ff:00.1 Host bridge: Intel Corporation Core Processor QuickPath Architecture System Address Decoder (rev 05) ff:02.0 Host bridge: Intel Corporation Core Processor QPI Link 0 (rev 05) ff:02.1 Host bridge: Intel Corporation Core Processor QPI Physical 0 (rev 05) ff:02.2 Host bridge: Intel Corporation Core Processor Reserved (rev 05) ff:02.3 Host bridge: Intel Corporation Core Processor Reserved (rev 05) I hope this information is of some help.

  Read the article

• Apache virtual host does not work properly

  - by Jori

  I have read a lot of information all over the Internet regarding this subject, and can not figure out what I'am doing wrong. I'm trying to host two websites under different names locally under Windows 7 with Apaches Virtual Hosting functionality. This is what I have done already: In the httpd.conf file I uncommented the following line, so that the virtual host configuration file will be included in the main configuration sequence. # Virtual hosts Include conf/extra/httpd-vhosts.conf This is how I edited my httpd-vhosts.conf: # # Virtual Hosts # # If you want to maintain multiple domains/hostnames on your # machine you can setup VirtualHost containers for them. Most configurations # use only name-based virtual hosts so the server doesn't need to worry about # IP addresses. This is indicated by the asterisks in the directives below. # # Please see the documentation at # <URL:http://httpd.apache.org/docs/2.2/vhosts/> # for further details before you try to setup virtual hosts. # # You may use the command line option '-S' to verify your virtual host # configuration. # # Use name-based virtual hosting. # NameVirtualHost *:80 # # VirtualHost example: # Almost any Apache directive may go into a VirtualHost container. # The first VirtualHost section is used for all requests that do not # match a ServerName or ServerAlias in any <VirtualHost> block. # #<VirtualHost *:80> # ServerAdmin [email protected] # DocumentRoot "C:/apache/docs/dummy-host.localhost" # ServerName dummy-host.localhost # ServerAlias www.dummy-host.localhost # ErrorLog "logs/dummy-host.localhost-error.log" # CustomLog "logs/dummy-host.localhost-access.log" common #</VirtualHost> # #<VirtualHost *:80> # ServerAdmin [email protected] # DocumentRoot "C:/apache/docs/dummy-host2.localhost" # ServerName dummy-host2.localhost # ErrorLog "logs/dummy-host2.localhost-error.log" # CustomLog "logs/dummy-host2.localhost-access.log" common #</VirtualHost> <VirtualHost *:80> ServerName arterieur DocumentRoot "J:/webcontent/www20" <Directory "J:/webcontent/www20"> Order allow,deny Allow from all </Directory> </VirtualHost> As you can see I commented the Virtual Host examples out and added my own one (I did one for this example). Also am I sure that J:\webcontent\www20 exists. At last I edited the Windows host file located in: C:\Windows\System32\drivers\etc\hosts, now it looks this: # Copyright (c) 1993-2009 Microsoft Corp. # # This is a sample HOSTS file used by Microsoft TCP/IP for Windows. # # This file contains the mappings of IP addresses to host names. Each # entry should be kept on an individual line. The IP address should # be placed in the first column followed by the corresponding host name. # The IP address and the host name should be separated by at least one # space. # # Additionally, comments (such as these) may be inserted on individual # lines or following the machine name denoted by a '#' symbol. # # For example: # # 102.54.94.97 rhino.acme.com # source server # 38.25.63.10 x.acme.com # x client host # localhost name resolution is handled within DNS itself. # 127.0.0.1 localhost # ::1 localhost 127.0.0.1 arterieur Then I restarted Apache with the Apache Service Monitor, and it gave me the following fatal error: The requested operation has failed!, I tried to look at the apache/logs/error.log file but I did not log anything, I guess it only logs the errors after startup. Does anyone knows what I'am doing wrong?

  Read the article

• virtual host not working in windows7 xampp

  - by K.B Panamaldeniya-littletipz

  hi i am using windows7 and xampp , i want to create a virtual host . so i added 127.0.0.1 myawesomeproject to my C:\Windows\System32\drivers\etc\hosts like this # Copyright (c) 1993-2009 Microsoft Corp. # # This is a sample HOSTS file used by Microsoft TCP/IP for Windows. # # This file contains the mappings of IP addresses to host names. Each # entry should be kept on an individual line. The IP address should # be placed in the first column followed by the corresponding host name. # The IP address and the host name should be separated by at least one # space. # # Additionally, comments (such as these) may be inserted on individual # lines or following the machine name denoted by a '#' symbol. # # For example: # # 102.54.94.97 rhino.acme.com # source server # 38.25.63.10 x.acme.com # x client host # localhost name resolution is handled within DNS itself. 127.0.0.1 localhost 127.0.0.1 myawesomeproject ::1 localhost and i added some lines to C:\xampp\apache\conf\extra\httpd-vhosts.conf like this # # Virtual Hosts # # If you want to maintain multiple domains/hostnames on your # machine you can setup VirtualHost containers for them. Most configurations # use only name-based virtual hosts so the server doesn't need to worry about # IP addresses. This is indicated by the asterisks in the directives below. # # Please see the documentation at # <URL:http://httpd.apache.org/docs/2.2/vhosts/> # for further details before you try to setup virtual hosts. # # You may use the command line option '-S' to verify your virtual host # configuration. # # Use name-based virtual hosting. # NameVirtualHost *:80 # # VirtualHost example: # Almost any Apache directive may go into a VirtualHost container. # The first VirtualHost section is used for all requests that do not # match a ServerName or ServerAlias in any <VirtualHost> block. # ##<VirtualHost *:80> ##ServerAdmin [email protected] ##DocumentRoot "C:/xampp/htdocs/dummy-host.localhost" ##ServerName dummy-host.localhost ##ServerAlias www.dummy-host.localhost ##ErrorLog "logs/dummy-host.localhost-error.log" ##CustomLog "logs/dummy-host.localhost-access.log" combined ##</VirtualHost> ##<VirtualHost *:80> ##ServerAdmin [email protected] ##DocumentRoot "C:/xampp/htdocs/dummy-host2.localhost" ##ServerName dummy-host2.localhost ##ServerAlias www.dummy-host2.localhost ##ErrorLog "logs/dummy-host2.localhost-error.log" ##CustomLog "logs/dummy-host2.localhost-access.log" combined ##</VirtualHost> <VirtualHost *> DocumentRoot "C:\xampp\htdocs" ServerName localhost </VirtualHost> <VirtualHost *> <VirtualHost *:80> ServerAdmin [email protected] DocumentRoot c:\myawesomeproject ServerName localhost <Directory "c:\myawesomeproject"> Order allow,deny Allow from all </Directory> </VirtualHost> i created a folder called myawesomeproject in my c drive . when i type http://myawesomeproject it is rederecting to http://myawesomeproject/xampp i added another folder 'test' inside myawesomeproject . so the path to 'test' is C:/myawesomeproject/test . the problem is when i type http://myawesomeproject/test it gives an error. it says Object not found! The requested URL was not found on this server. If you entered the URL manually please check your spelling and try again. If you think this is a server error, please contact the webmaster. Error 404 myawesomeproject 8/22/2011 4:30:29 PM Apache/2.2.17 (Win32) mod_ssl/2.2.17 OpenSSL/0.9.8o PHP/5.3.4 mod_perl/2.0.4 Perl/v5.10.1 why is this . how can i create a virtual host........................ :(

  Read the article

• DNS Problems (NIGHTMARES!) with BIND and Virtualmin

  - by Nyxynyx

  I have a webserver (Ubuntu 12.04 with LAMP) using Virtualmin / Webmin. Because I just moved from a Cpanel system, I am having a nightmare configuring the DNS! Using intoDNS.com, the failed reports are: Mismatched NS records WARNING: One or more of your nameservers did not return any of your NS records. DNS servers responded ERROR: One or more of your nameservers did not respond: The ones that did not respond are: 123.123.123.123 213.251.188.141x Multiple Nameservers ERROR: Looks like you have less than 2 nameservers. According to RFC2182 section 5 you must have at least 3 nameservers, and no more than 7. Having 2 nameservers is also ok by me. Missing nameservers reported by your nameserver You should already know that your NS records at your nameservers are missing, so here it is again: ns1.mydomain.com. sdns2.ovh.net. SOA record No valid SOA record came back! MX Records WWW A Record ERROR: I could not get any A records for www.mydomain.com! Step-by-Step of my Attempt In my domain registrar (Namecheap), I registered ns1.mydomain.com as a nameserver, pointing to the IP address of my web server which is running bind9. The domain is setup with DNS ns1.mydomain.com and sdns2.ovh.net. sdns2.ovh.net is a secondary DNS server (SLAVE and pointing mydomain.com to the IP address of my web server) Webserver domain: mydomain.com Webserver hostname: ns4000000.ip-123-123-123.net Webserver IP: 123.123.123.123 Under Virtualmin, I edited the default Virtual server template, BIND DNS records for new domains: ns1.mydomain.com Master DNS server hostname: ns1.mydomain.com Next I created a Virtual server using that server template. This is what I've done but its still not working! Any ideas? I've been stuck for days, thank you for all your help! service bind9 status * bind9 is running lsof -i :53 COMMAND PID USER FD TYPE DEVICE SIZE/OFF NODE NAME named 6966 bind 20u IPv6 338583 0t0 TCP *:domain (LISTEN) named 6966 bind 21u IPv4 338588 0t0 TCP localhost.localdomain:domain (LISTEN) named 6966 bind 22u IPv4 338590 0t0 TCP ns4000000.ip-123-123-123.net:domain (LISTEN) named 6966 bind 512u IPv6 338582 0t0 UDP *:domain named 6966 bind 513u IPv4 338587 0t0 UDP localhost.localdomain:domain named 6966 bind 514u IPv4 338589 0t0 UDP ns4000000.ip-123-123-123.net:domain /etc/resolv.con (Not sure how 213.186.33.99 got here) nameserver 127.0.0.1 nameserver 213.186.33.99 search ovh.net host 123.123.123.123 (my web server's IP) 13.60.245.198.in-addr.arpa domain name pointer ns4000000.ip-123-123-123.net. nslookup 213.186.33.99 Server: 127.0.0.1 Address: 127.0.0.1#53 Non-authoritative answer: 99.33.186.213.in-addr.arpa name = cdns.ovh.net. Authoritative answers can be found from: 33.186.213.in-addr.arpa nameserver = ns.ovh.net. 33.186.213.in-addr.arpa nameserver = dns.ovh.net. nslookup ns1.mydomain.com ;; Got SERVFAIL reply from 127.0.0.1, trying next server ;; connection timed out; no servers could be reached nslookup ns2.mydomain.com ;; Got SERVFAIL reply from 127.0.0.1, trying next server ;; connection timed out; no servers could be reached nslookup www.mydomain.com ;; Got SERVFAIL reply from 127.0.0.1, trying next server ;; connection timed out; no servers could be reached dig mydomain.com ; <<>> DiG 9.8.1-P1 <<>> mydomain.com ;; global options: +cmd ;; Got answer: ;; ->>HEADER<<- opcode: QUERY, status: SERVFAIL, id: 43540 ;; flags: qr rd ra; QUERY: 1, ANSWER: 0, AUTHORITY: 0, ADDITIONAL: 0 ;; QUESTION SECTION: ;mydomain.com. IN A ;; Query time: 0 msec ;; SERVER: 127.0.0.1#53(127.0.0.1) ;; WHEN: Thu Oct 11 11:30:09 2012 ;; MSG SIZE rcvd: 30 dig ns1.mydomain.com ; <<>> DiG 9.8.1-P1 <<>> ns1.mydomain.com ;; global options: +cmd ;; Got answer: ;; ->>HEADER<<- opcode: QUERY, status: SERVFAIL, id: 31254 ;; flags: qr rd ra; QUERY: 1, ANSWER: 0, AUTHORITY: 0, ADDITIONAL: 0 ;; QUESTION SECTION: ;ns1.mydomain.com. IN A ;; Query time: 0 msec ;; SERVER: 127.0.0.1#53(127.0.0.1) ;; WHEN: Thu Oct 11 11:30:16 2012 ;; MSG SIZE rcvd: 34 /etc/bind/named.conf include "/etc/bind/named.conf.options"; include "/etc/bind/named.conf.local"; include "/etc/bind/named.conf.default-zones"; /etc/bind/named.conf.default-zones zone "." { type hint; file "/etc/bind/db.root"; }; zone "localhost" { type master; file "/etc/bind/db.local"; }; zone "127.in-addr.arpa" { type master; file "/etc/bind/db.127"; }; zone "0.in-addr.arpa" { type master; file "/etc/bind/db.0"; }; zone "255.in-addr.arpa" { type master; file "/etc/bind/db.255"; }; /etc/bind/named.conf.local zone "mydomain.com" { type master; file "/var/lib/bind/mydomain.com.hosts"; allow-transfer { 127.0.0.1; localnets; }; }; /etc/bind/named.conf.options options { directory "/var/cache/bind"; dnssec-validation auto; auth-nxdomain no; # conform to RFC1035 listen-on-v6 { any; }; // allow-recursion { 127.0.0.1; }; // transfer-source; }; named-checkconf -z dns_master_load: /var/lib/bind/mydomain.com.hosts:21: unexpected end of line dns_master_load: /var/lib/bind/mydomain.com.hosts:20: unexpected end of input /var/lib/bind/mydomain.com.hosts: file does not end with newline zone mydomain.com/IN: loading from master file /var/lib/bind/mydomain.com.hosts failed: unexpected end of input zone mydomain.com/IN: not loaded due to errors. _default/mydomain.com/IN: unexpected end of input zone localhost/IN: loaded serial 2 zone 127.in-addr.arpa/IN: loaded serial 1 zone 0.in-addr.arpa/IN: loaded serial 1 zone 255.in-addr.arpa/IN: loaded serial 1 iptables -L Chain INPUT (policy ACCEPT) target prot opt source destination ACCEPT udp -- anywhere anywhere udp dpt:domain ACCEPT tcp -- anywhere anywhere tcp dpt:20000 ACCEPT tcp -- anywhere anywhere tcp dpt:webmin ACCEPT tcp -- anywhere anywhere tcp dpt:https ACCEPT tcp -- anywhere anywhere tcp dpt:http ACCEPT tcp -- anywhere anywhere tcp dpt:imaps ACCEPT tcp -- anywhere anywhere tcp dpt:imap2 ACCEPT tcp -- anywhere anywhere tcp dpt:pop3s ACCEPT tcp -- anywhere anywhere tcp dpt:pop3 ACCEPT tcp -- anywhere anywhere tcp dpt:ftp-data ACCEPT tcp -- anywhere anywhere tcp dpt:ftp ACCEPT tcp -- anywhere anywhere tcp dpt:domain ACCEPT tcp -- anywhere anywhere tcp dpt:submission ACCEPT tcp -- anywhere anywhere tcp dpt:smtp ACCEPT tcp -- anywhere anywhere tcp dpt:ssh ACCEPT all -- anywhere anywhere Chain FORWARD (policy ACCEPT) target prot opt source destination Chain OUTPUT (policy ACCEPT) target prot opt source destination

  Read the article

• cannot access a site from Mac OSX Lion but can from other machines on network?

  - by house9

  SOLVED: The issue is with the hamachi client, hamachi is hi-jacking all of the 5.0.0.0/8 address block http://en.wikipedia.org/wiki/Hamachi_(software)#Criticism http://b.logme.in/2012/11/07/changes-to-hamachi-on-november-19th/ The fix on Mac LogMeIn Hamachi Preferences Settings Advanced Peer Connections IP protocol mode IPv6 only (default is both) If you can only connect to some of your network over IPv4 this 'fix' will NOT work for you ----- A few weeks ago I started using a service - https://semaphoreapp.com I think they made DNS changes a week ago and ever since I cannot access the site from my Mac OSX Lion (10.7.4) machine (my main development machine) but I can access the site from other machines on my network ipad windows machine MacMini (10.6.8) After some google searching I tried both of these dscacheutil -flushcache sudo killall -HUP mDNSResponder but no go, I've contacted semaphoreapp as well, but nothing so far - also of interest, one of my colleagues has the exact same problem, cannot access via Mac OSX Lion but can via windows machine, we work remotely and are not on the same ISP some additional info Lion (10.7.4) cannot access site host semaphoreapp.com semaphoreapp.com has address 5.9.53.16 ping semaphoreapp.com PING semaphoreapp.com (5.9.53.16): 56 data bytes Request timeout for icmp_seq 0 Request timeout for icmp_seq 1 Request timeout for icmp_seq 2 Request timeout for icmp_seq 3 ping: sendto: No route to host Request timeout for icmp_seq 4 ping: sendto: Host is down Request timeout for icmp_seq 5 ping: sendto: Host is down Request timeout for icmp_seq 6 ping: sendto: Host is down Request timeout for icmp_seq 7 .... traceroute semaphoreapp.com traceroute to semaphoreapp.com (5.9.53.16), 64 hops max, 52 byte packets 1 * * * 2 * * * traceroute: sendto: No route to host 3 traceroute: wrote semaphoreapp.com 52 chars, ret=-1 *traceroute: sendto: Host is down traceroute: wrote semaphoreapp.com 52 chars, ret=-1 .... and MacMini (10.6.8) can access it host semaphoreapp.com semaphoreapp.com has address 5.9.53.16 ping semaphoreapp.com PING semaphoreapp.com (5.9.53.16): 56 data bytes 64 bytes from 5.9.53.16: icmp_seq=0 ttl=44 time=191.458 ms 64 bytes from 5.9.53.16: icmp_seq=1 ttl=44 time=202.923 ms 64 bytes from 5.9.53.16: icmp_seq=2 ttl=44 time=180.746 ms 64 bytes from 5.9.53.16: icmp_seq=3 ttl=44 time=200.616 ms 64 bytes from 5.9.53.16: icmp_seq=4 ttl=44 time=178.818 ms .... traceroute semaphoreapp.com traceroute to semaphoreapp.com (5.9.53.16), 64 hops max, 52 byte packets 1 192.168.0.1 (192.168.0.1) 1.677 ms 1.446 ms 1.445 ms 2 * LOCAL ISP 11.957 ms * 3 etc... 10.704 ms 14.183 ms 9.341 ms 4 etc... 32.641 ms 12.147 ms 10.850 ms 5 etc.... 44.205 ms 54.563 ms 36.243 ms 6 vlan139.car1.seattle1.level3.net (4.53.145.165) 50.136 ms 45.873 ms 30.396 ms 7 ae-32-52.ebr2.seattle1.level3.net (4.69.147.182) 31.926 ms 40.507 ms 49.993 ms 8 ae-2-2.ebr2.denver1.level3.net (4.69.132.54) 78.129 ms 59.674 ms 49.905 ms 9 ae-3-3.ebr1.chicago2.level3.net (4.69.132.62) 99.019 ms 82.008 ms 76.074 ms 10 ae-1-100.ebr2.chicago2.level3.net (4.69.132.114) 96.185 ms 75.658 ms 75.662 ms 11 ae-6-6.ebr2.washington12.level3.net (4.69.148.145) 104.322 ms 105.563 ms 118.480 ms 12 ae-5-5.ebr2.washington1.level3.net (4.69.143.221) 93.646 ms 99.423 ms 96.067 ms 13 ae-41-41.ebr2.paris1.level3.net (4.69.137.49) 177.744 ms ae-44-44.ebr2.paris1.level3.net (4.69.137.61) 199.363 ms 198.405 ms 14 ae-47-47.ebr1.frankfurt1.level3.net (4.69.143.141) 176.876 ms ae-45-45.ebr1.frankfurt1.level3.net (4.69.143.133) 170.994 ms ae-46-46.ebr1.frankfurt1.level3.net (4.69.143.137) 177.308 ms 15 ae-61-61.csw1.frankfurt1.level3.net (4.69.140.2) 176.769 ms ae-91-91.csw4.frankfurt1.level3.net (4.69.140.14) 178.676 ms 173.644 ms 16 ae-2-70.edge7.frankfurt1.level3.net (4.69.154.75) 180.407 ms ae-3-80.edge7.frankfurt1.level3.net (4.69.154.139) 174.861 ms 176.578 ms 17 as33891-net.edge7.frankfurt1.level3.net (195.16.162.94) 175.448 ms 185.658 ms 177.081 ms 18 hos-bb1.juniper4.rz16.hetzner.de (213.239.240.202) 188.700 ms 190.332 ms 188.196 ms 19 hos-tr4.ex3k14.rz16.hetzner.de (213.239.233.98) 199.632 ms hos-tr3.ex3k14.rz16.hetzner.de (213.239.233.66) 185.938 ms hos-tr2.ex3k14.rz16.hetzner.de (213.239.230.34) 182.378 ms 20 * * * 21 * * * 22 * * * any ideas? EDIT: adding tcpdump MacMini (which can connect) while running - ping semaphoreapp.com sudo tcpdump -v -i en0 dst semaphoreapp.com Password: tcpdump: listening on en0, link-type EN10MB (Ethernet), capture size 65535 bytes 17:33:03.337165 IP (tos 0x0, ttl 64, id 20153, offset 0, flags [none], proto ICMP (1), length 84, bad cksum 0 (->3129)!) 192.168.0.6 > static.16.53.9.5.clients.your-server.de: ICMP echo request, id 61918, seq 0, length 64 17:33:04.337279 IP (tos 0x0, ttl 64, id 26049, offset 0, flags [none], proto ICMP (1), length 84, bad cksum 0 (->1a21)!) 192.168.0.6 > static.16.53.9.5.clients.your-server.de: ICMP echo request, id 61918, seq 1, length 64 17:33:05.337425 IP (tos 0x0, ttl 64, id 47854, offset 0, flags [none], proto ICMP (1), length 84, bad cksum 0 (->c4f3)!) 192.168.0.6 > static.16.53.9.5.clients.your-server.de: ICMP echo request, id 61918, seq 2, length 64 17:33:06.337548 IP (tos 0x0, ttl 64, id 24772, offset 0, flags [none], proto ICMP (1), length 84, bad cksum 0 (->1f1e)!) 192.168.0.6 > static.16.53.9.5.clients.your-server.de: ICMP echo request, id 61918, seq 3, length 64 17:33:07.337670 IP (tos 0x0, ttl 64, id 8171, offset 0, flags [none], proto ICMP (1), length 84, bad cksum 0 (->5ff7)!) 192.168.0.6 > static.16.53.9.5.clients.your-server.de: ICMP echo request, id 61918, seq 4, length 64 17:33:08.337816 IP (tos 0x0, ttl 64, id 35810, offset 0, flags [none], proto ICMP (1), length 84, bad cksum 0 (->f3ff)!) 192.168.0.6 > static.16.53.9.5.clients.your-server.de: ICMP echo request, id 61918, seq 5, length 64 17:33:09.337948 IP (tos 0x0, ttl 64, id 31120, offset 0, flags [none], proto ICMP (1), length 84, bad cksum 0 (->652)!) 192.168.0.6 > static.16.53.9.5.clients.your-server.de: ICMP echo request, id 61918, seq 6, length 64 ^C 7 packets captured 1047 packets received by filter 0 packets dropped by kernel OSX Lion (cannot connect) while running - ping semaphoreapp.com # wireless ~ $ sudo tcpdump -v -i en1 dst semaphoreapp.com Password: tcpdump: listening on en1, link-type EN10MB (Ethernet), capture size 65535 bytes ^C 0 packets captured 262 packets received by filter 0 packets dropped by kernel and # wired ~ $ sudo tcpdump -v -i en0 dst semaphoreapp.com tcpdump: listening on en0, link-type EN10MB (Ethernet), capture size 65535 bytes ^C 0 packets captured 219 packets received by filter 0 packets dropped by kernel above output after Request timeout for icmp_seq 25 or 30 times from ping. I don't know much about tcpdump, but to me it doesn't seem like the ping requests are leaving my machine?

  Read the article

• 12.04 making BCM4313 card work with aircrack-ng?

  - by Charles Forest

  I'm a real Linux Noob, just started using it (this month) and until now i had no issues. now i'm trying to set-up aircrack-ng on my laptop, but it seems like it's using the worst card possible (or almost) there is a TON of tutorial on this card (seems to be hell to set-up) i have tryed some, but i ended up uninstalling my drivers, messing with my desktops, and ended by having no more "X" to close my windows (i have no clue how i ended there) i just re-installed my linux (took me 2 hours to setup everything again), but now i'm a bit "Scared" to try tutorials randomly again. Right now it says the driver is wl, wich is not the one i want (AFAIK it's not supported) i'm not sure what kind of informations are needed, but here's what i think could be usefull. lspci -knn 00:00.0 Host bridge [0600]: Intel Corporation 2nd Generation Core Processor Family DRAM Controller [8086:0104] (rev 09) Subsystem: Samsung Electronics Co Ltd Device [144d:c0a5] Kernel driver in use: agpgart-intel 00:01.0 PCI bridge [0604]: Intel Corporation Xeon E3-1200/2nd Generation Core Processor Family PCI Express Root Port [8086:0101] (rev 09) Kernel driver in use: pcieport Kernel modules: shpchp 00:02.0 VGA compatible controller [0300]: Intel Corporation 2nd Generation Core Processor Family Integrated Graphics Controller [8086:0116] (rev 09) Subsystem: Samsung Electronics Co Ltd Device [144d:c0a5] Kernel driver in use: i915 Kernel modules: i915 00:16.0 Communication controller [0780]: Intel Corporation 6 Series/C200 Series Chipset Family MEI Controller #1 [8086:1c3a] (rev 04) Subsystem: Samsung Electronics Co Ltd Device [144d:c0a5] Kernel driver in use: mei Kernel modules: mei 00:1a.0 USB controller [0c03]: Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #2 [8086:1c2d] (rev 04) Subsystem: Samsung Electronics Co Ltd Device [144d:c0a5] Kernel driver in use: ehci_hcd 00:1b.0 Audio device [0403]: Intel Corporation 6 Series/C200 Series Chipset Family High Definition Audio Controller [8086:1c20] (rev 04) Subsystem: Samsung Electronics Co Ltd Device [144d:c0a5] Kernel driver in use: snd_hda_intel Kernel modules: snd-hda-intel 00:1c.0 PCI bridge [0604]: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 1 [8086:1c10] (rev b4) Kernel driver in use: pcieport Kernel modules: shpchp 00:1c.3 PCI bridge [0604]: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 4 [8086:1c16] (rev b4) Kernel driver in use: pcieport Kernel modules: shpchp 00:1c.4 PCI bridge [0604]: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 5 [8086:1c18] (rev b4) Kernel driver in use: pcieport Kernel modules: shpchp 00:1d.0 USB controller [0c03]: Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #1 [8086:1c26] (rev 04) Subsystem: Samsung Electronics Co Ltd Device [144d:c0a5] Kernel driver in use: ehci_hcd 00:1f.0 ISA bridge [0601]: Intel Corporation HM65 Express Chipset Family LPC Controller [8086:1c49] (rev 04) Subsystem: Samsung Electronics Co Ltd Device [144d:c0a5] Kernel modules: iTCO_wdt 00:1f.2 SATA controller [0106]: Intel Corporation 6 Series/C200 Series Chipset Family 6 port SATA AHCI Controller [8086:1c03] (rev 04) Subsystem: Samsung Electronics Co Ltd Device [144d:c0a5] Kernel driver in use: ahci 00:1f.3 SMBus [0c05]: Intel Corporation 6 Series/C200 Series Chipset Family SMBus Controller [8086:1c22] (rev 04) Subsystem: Samsung Electronics Co Ltd Device [144d:c0a5] Kernel modules: i2c-i801 01:00.0 3D controller [0302]: NVIDIA Corporation GF108 [GeForce GT 540M] [10de:0df4] (rev a1) Subsystem: Samsung Electronics Co Ltd Device [144d:c0a5] Kernel driver in use: nouveau Kernel modules: nouveau, nvidiafb WIRELESS CARD 02:00.0 Network controller [0280]: Broadcom Corporation BCM4313 802.11b/g/n Wireless LAN Controller [14e4:4727] (rev 01) Subsystem: Wistron NeWeb Corp. Device [185f:051a] Kernel driver in use: wl Kernel modules: wl, bcma, brcmsmac REST... 03:00.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller [10ec:8168] (rev 06) Subsystem: Samsung Electronics Co Ltd Device [144d:c0a5] Kernel driver in use: r8169 Kernel modules: r8169 04:00.0 USB controller [0c03]: NEC Corporation uPD720200 USB 3.0 Host Controller [1033:0194] (rev 04) Subsystem: Samsung Electronics Co Ltd Device [144d:c0a5] Kernel driver in use: xhci_hcd Also, if i'm "screwed" with my hardware, just tell me.

  Read the article

• Easy Made Easier - Networking

  - by dragonfly

      In my last post, I highlighted the feature of the Appliance Manager Configurator to auto-fill some fields based on previous field values, including host names based on System Name and sequential IP addresses from the first IP address entered. This can make configuration a little faster and a little less subject to data entry errors, particularly if you are doing the configuration on the Oracle Database Appliance itself.     The Oracle Database Appliance Appliance Manager Configurator is available for download here. But why would you download it, if it comes pre-installed on the Oracle Database Appliance? A common reason for customers interested in this new Engineered System is to get a good idea of how easy it is to configure. Beyond that, you can save the resulting configuration as a file, and use it on an Oracle Database Appliance. This allows you to verify the data entered in advance, and in the comfort of your office. In addition, the topic of this post is another strong reason to download and use the Appliance Manager Configurator prior to deploying your Oracle Database Appliance.     The most common source of hiccups in deploying an Oracle Database Appliance, based on my experiences with a variety of customers, involves the network configuration. It is during Step 11, when network validation occurs, that these come to light, which is almost half way through the 24 total steps, and can be frustrating, whether it was a typo, DNS mis-configuration or IP address already in use. This is why I recommend as a best practice taking advantage of the Appliance Manager Configurator prior to deploying an Oracle Database Appliance.     Why? Not only do you get the benefit of being able to double check your entries before you even start on the Oracle Database Appliance, you can also take advantage of the Network Validation step. This is the final step before you review all the data and can save it to a text file. It can be skipped, if you aren't ready or are not connected to the network that the Oracle Database Appliance will be on. My recommendation, though, is to run the Appliance Manager Configurator on your laptop, enter the data or re-load a previously saved file of the data, and then connect to the network that the Oracle Database Appliance will be on. Now run the Network Validation. It will check to make sure that the host names you entered are in DNS and do resolve to the IP addresses you specifiied. It will also ping the IP Addresses you specified, so that you can verify that no other machine is already using them (yes, that has happened at customer sites).     After you have completed the validation, as seen in the screen shot below, you can review the results and move on to saving your settings to a file for use on your Oracle Database Appliance, or if there are errors, you can use the Back button to return to the appropriate screen and correct the data. Once you are satisfied with the Network Validation, just check the Skip/Ignore Network Validation checkbox at the top of the screen, then click Next. Is the Network Validation in the Appliance Manager Configurator required? No, but it can save you time later. I should also note that the Network Validation screen is not part of the Appliance Manager Configurator that currently ships on the Oracle Database Appliance, so this is the easiest way to verify your network configuration.     I hope you are finding this series of posts useful. My next post will cover some aspects of the windowing environment that gets run by the 'startx' command on the Oracle Database Appliance, since this is needed to run the Appliance Manager Configurator via a direct connected monitor, keyboard and mouse, or via the ILOM. If it's been a while since you've used an OpenWindows environment, you'll want to check it out.

  Read the article

• Observing flow control idle time in TCP

  - by user12820842

  Previously I described how to observe congestion control strategies during transmission, and here I talked about TCP's sliding window approach for handling flow control on the receive side. A neat trick would now be to put the pieces together and ask the following question - how often is TCP transmission blocked by congestion control (send-side flow control) versus a zero-sized send window (which is the receiver saying it cannot process any more data)? So in effect we are asking whether the size of the receive window of the peer or the congestion control strategy may be sub-optimal. The result of such a problem would be that we have TCP data that we could be transmitting but we are not, potentially effecting throughput. So flow control is in effect: when the congestion window is less than or equal to the amount of bytes outstanding on the connection. We can derive this from args[3]-tcps_snxt - args[3]-tcps_suna, i.e. the difference between the next sequence number to send and the lowest unacknowledged sequence number; and when the window in the TCP segment received is advertised as 0 We time from these events until we send new data (i.e. args[4]-tcp_seq = snxt value when window closes. Here's the script: #!/usr/sbin/dtrace -s #pragma D option quiet tcp:::send / (args[3]-tcps_snxt - args[3]-tcps_suna) = args[3]-tcps_cwnd / { cwndclosed[args[1]-cs_cid] = timestamp; cwndsnxt[args[1]-cs_cid] = args[3]-tcps_snxt; @numclosed["cwnd", args[2]-ip_daddr, args[4]-tcp_dport] = count(); } tcp:::send / cwndclosed[args[1]-cs_cid] && args[4]-tcp_seq = cwndsnxt[args[1]-cs_cid] / { @meantimeclosed["cwnd", args[2]-ip_daddr, args[4]-tcp_dport] = avg(timestamp - cwndclosed[args[1]-cs_cid]); @stddevtimeclosed["cwnd", args[2]-ip_daddr, args[4]-tcp_dport] = stddev(timestamp - cwndclosed[args[1]-cs_cid]); @numclosed["cwnd", args[2]-ip_daddr, args[4]-tcp_dport] = count(); cwndclosed[args[1]-cs_cid] = 0; cwndsnxt[args[1]-cs_cid] = 0; } tcp:::receive / args[4]-tcp_window == 0 && (args[4]-tcp_flags & (TH_SYN|TH_RST|TH_FIN)) == 0 / { swndclosed[args[1]-cs_cid] = timestamp; swndsnxt[args[1]-cs_cid] = args[3]-tcps_snxt; @numclosed["swnd", args[2]-ip_saddr, args[4]-tcp_dport] = count(); } tcp:::send / swndclosed[args[1]-cs_cid] && args[4]-tcp_seq = swndsnxt[args[1]-cs_cid] / { @meantimeclosed["swnd", args[2]-ip_daddr, args[4]-tcp_sport] = avg(timestamp - swndclosed[args[1]-cs_cid]); @stddevtimeclosed["swnd", args[2]-ip_daddr, args[4]-tcp_sport] = stddev(timestamp - swndclosed[args[1]-cs_cid]); swndclosed[args[1]-cs_cid] = 0; swndsnxt[args[1]-cs_cid] = 0; } END { printf("%-6s %-20s %-8s %-25s %-8s %-8s\n", "Window", "Remote host", "Port", "TCP Avg WndClosed(ns)", "StdDev", "Num"); printa("%-6s %-20s %-8d %@-25d %@-8d %@-8d\n", @meantimeclosed, @stddevtimeclosed, @numclosed); } So this script will show us whether the peer's receive window size is preventing flow ("swnd" events) or whether congestion control is limiting flow ("cwnd" events). As an example I traced on a server with a large file transfer in progress via a webserver and with an active ssh connection running "find / -depth -print". Here is the output: ^C Window Remote host Port TCP Avg WndClosed(ns) StdDev Num cwnd 10.175.96.92 80 86064329 77311705 125 cwnd 10.175.96.92 22 122068522 151039669 81 So we see in this case, the congestion window closes 125 times for port 80 connections and 81 times for ssh. The average time the window is closed is 0.086sec for port 80 and 0.12sec for port 22. So if you wish to change congestion control algorithm in Oracle Solaris 11, a useful step may be to see if congestion really is an issue on your network. Scripts like the one posted above can help assess this, but it's worth reiterating that if congestion control is occuring, that's not necessarily a problem that needs fixing. Recall that congestion control is about controlling flow to prevent large-scale drops, so looking at congestion events in isolation doesn't tell us the whole story. For example, are we seeing more congestion events with one control algorithm, but more drops/retransmission with another? As always, it's best to start with measures of throughput and latency before arriving at a specific hypothesis such as "my congestion control algorithm is sub-optimal".

  Read the article

• Hyper-V for Developers Part 1 Internal Networks

  Over the last year, weve been working with Microsoft to build training and demo content for the next version of Office Communications Server code-named Microsoft Communications Server 14.  This involved building multi-server demo environments in Hyper-V, getting them running on demo servers which we took to TechEd, PDC, and other training events, and sometimes connecting the demo servers to the show networks at those events.  ITPro stuff that should scare the hell out of a developer! It can get ugly when I occasionally have to venture into ITPro land.  Lets leave it at that. Having gone through this process about 10 to 15 times in the last year, I finally have it down.  This blog series is my attempt to put all that knowledge in one place if anything, so I can find it somewhere when I need it again.  Ill start with the most simple scenario and then build on top of it in future blog posts. If youre an ITPro, please resist the urge to laugh at how trivial this is. Internal Hyper-V Networks Lets start simple.  An internal network is one that intended only for the virtual machines that are going to be on that network it enables them to communicate with each other. Create an Internal Network On your host machine, fire up the Hyper-V Manager and click the Virtual Network Manager in the Actions panel. Select Internal and leave all the other default values. Give the virtual network a name, and leave all the other default values. After the virtual network is created, open the Network and Sharing Center and click Change Adapter Settings to see the list of network connections. The only thing I recommend that you do is to give this connection a friendly label, e.g. Hyper-V Internal.  When you have multiple networks and virtual networks on the host machines, this helps group the networks so you can easily differentiate them from each other.  Otherwise, dont touch it, only bad things can happen. Connect the Virtual Machines to the Internal Network Im assuming that you have more than 1 virtual machine already configured in Hyper-V, for example a Domain Controller, and Exchange Server, and a SharePoint Server. What you need to do is basically plug in the network to the virtual machine.  In order to do this, the machine needs to have a virtual network adapter.  If the VM doesnt have a network adapter, open the VMs Settings and click Add Hardware in the left pane.  Choose the virtual network to which to bind the adapter to. If you already have a virtual network adapter on the VM, simply connect it to the virtual network. Assign IP Addresses to the Virtual Machines on the Internal Network Open the Network and Sharing Center on your VM, there should only be 1 network at this time.  Open the Properties of the connection, select Internet Protocol Version 4 (TCP/IPv4) and hit Properties. In this environment, Im assigning IP addresses as 192.168.0.xxx.  This particular VM has an IP address of 192.168.0.40 with a subnet mask of 255.255.255.0, and a DNS Server of 192.168.0.18.  DNS is running on the Domain Controller VM which has an IP address of 192.168.0.18. Repeat this process on every VM in your environment, obviously assigning a unique IP address to each.  In an environment with a domain controller, you should now be able to ping the machines from each other. What Next? After completing this process, heres what you still cannot do: Access the internet from any of the VMs Remote desktop to a VM from the host Remote desktop to a VM over the network In the next post, well take a look configuring an External network adapter on the virtual machines.  Well then build on top of that so that you can RDP into the VMs from the host machine and over the network.Did you know that DotNetSlackers also publishes .net articles written by top known .net Authors? We already have over 80 articles in several categories including Silverlight. Take a look: here.

  Read the article

• socket.error: [Errno 10013] An attempt was made to access a socket in a way forbidden by its access

  - by Sean Ochoa

  Hello all. I'm trying to create a custom TCP stack using Python 2.6.5 on Windows 7 to serve valid http page requests on port 80 locally. But, I've run into a snag with what seems like Windows 7 tightened up security. This code worked on Vista. Here's my sample code: import SocketServer class MyTCPHandler(SocketServer.BaseRequestHandler): def handle(self): headerText = """HTTP/1.0 200 OK Date: Fri, 31 Dec 1999 23:59:59 GMT Content-Type: text/html Content-Length: 1354""" bodyText = "<html><body>some page</body></html>" self.request.send(headerText + "\n" + bodyText) if __name__ == "__main__": HOST, PORT = "localhost", 80 server = SocketServer.TCPServer((HOST, PORT), MyTCPHandler) server.serve_forever() C:\pythonpython TestServer.py Traceback (most recent call last): File "TestServer.py", line 19, in server = SocketServer.TCPServer((HOST, PORT), MyTCPHandler) File "C:\Python26\lib\SocketServer.py", line 400, in init self.server_bind() File "C:\Python26\lib\SocketServer.py", line 411, in server_bind self.socket.bind(self.server_address) File "", line 1, in bind socket.error: [Errno 10013] An attempt was made to access a socket in a way forbidden by its access permissions How exactly do I get this to work on Windows 7?

  Read the article

• How To Avoid a Perl script calling an Another Perl Script

  - by rockyurock

  Hello, i am calling a perl script client.pl from a main script to capture the output of client.pl in @output. is there anyway to avoid the use of these two files so i can use the output of client.pl in main.pl itself here is my code.... main.pl ======= my @output = readpipe("client.pl"); client.pl ========= #! /usr/bin/perl -w #use strict; use Socket; #initialize host and port my $host = shift || $FTP_SERVER; my $port = shift || $CLIENT_PORT; my $proto = getprotobyname('tcp'); #get the port address my $iaddr = inet_aton($host); my $paddr = sockaddr_in($port, $iaddr); #create the socket, connect to the port socket(SOCKET, PF_INET, SOCK_STREAM, $proto)or die "socket: $!\n"; connect(SOCKET, $paddr) or die "connect: $!\n"; my $line; while ($line = ) { print "$line\n"; } close SOCKET or die "close: $!"; /rocky..

  Read the article

• Installation of SAP Web Application Server 6.20 in Windows Vista

  - by karthikeyan b

  I tried installing trial version of sap netweaver 7.1 in windows vista in my laptop but i couldnt succeed there.. then i tried installing SAP WEB AS 6.20 now.I am able to succeed till 91% completion.After that i get some errors and the installation stops... if anybody have any experiences please share.it will be really helpful.I mentioned the complete log details below. nfo: INSTGUI.EXE Protocol version is 10. Message checksum is 7613888. Info: INSTGUI MessageFile Start message loading... Info: INSTGUI MessageFile Finished message loading. Info: InstController Prepare {} {} R3SETUP Version: Apr 24 2002 Info: InstController Prepare {} {} Logfile will be set to E:\R3SETUP\BSP.log Check E:\R3SETUP\BSP.log for further messages. Info: CommandFileController SyFileVersionSave {} {} Saving original content of file E:\R3SETUP\BSP.R3S ... Warning: CommandFileController SyFileCopy {} {} Function CopyFile() failed at location SyFileCopy-681 Warning: CommandFileController SyFileCopy {} {} errno: 5: Access is denied. Warning: CommandFileController SyFileCreateWithPermissions {} {} errno: 13: Permission denied Warning: CommandFileController SyPermissionSet {} {} Function SetNamedSecurityInfo() failed for E:\R3SETUP\BSP.R3S at location SyPermissionSet-2484 Warning: CommandFileController SyPermissionSet {} {} errno: 5: Access is denied. Error: CommandFileController StoreMasterTableFromCommandFile 2 333 Command file could not be opened. Error: CommandFileController SetKeytableForSect 2 333 CommandFile could not be updated Error: CommandFileController StoreMasterTableFromCommandFile 2 309 Command file could not be opened. Error: CommandFileController SetKeytableForSect 2 309 CommandFile could not be updated Info: CDSERVERBASE InternalColdKeyCheck 2 309 The CD KERNEL will not be copied. Info: CDSERVERBASE InternalColdKeyCheck 2 309 The CD DATA1 will not be copied. Info: CDSERVERBASE InternalColdKeyCheck 2 309 The CD DATA2 will not be copied. Error: CommandFileController StoreMasterTableFromCommandFile 2 333 Command file could not be opened. Error: CommandFileController SetKeytableForSect 2 333 CommandFile could not be updated Info: CENTRDBINSTANCE_NT_ADA SyCheckHostnameLookup 2 333 checking host name lookup for 'Karthikeyan' Info: CENTRDBINSTANCE_NT_ADA SyCheckHostnameLookup 2 333 offical host name for 'Karthikeyan' is 'Karthikeyan'. Info: CENTRDBINSTANCE_NT_ADA SyCheckHostnameLookup 2 333 host 'Karthikeyan' has ip address '115.184.71.93' Info: CENTRDBINSTANCE_NT_ADA SyCheckHostnameLookup 2 333 offical host name for '115.184.71.93' is 'Karthikeyan'. Info: CENTRDBINSTANCE_NT_ADA SyCheckHostnameLookup 2 333 checking host name lookup for 'Karthikeyan' Info: CENTRDBINSTANCE_NT_ADA SyCheckHostnameLookup 2 333 offical host name for 'Karthikeyan' is 'Karthikeyan'. Info: CENTRDBINSTANCE_NT_ADA SyCheckHostnameLookup 2 333 host 'Karthikeyan' has ip address '115.184.71.93' Info: CENTRDBINSTANCE_NT_ADA SyCheckHostnameLookup 2 333 offical host name for '115.184.71.93' is 'Karthikeyan'. Info: CENTRDBINSTANCE_NT_ADA SyCheckHostnameLookup 2 333 checking host name lookup for 'Karthikeyan' Info: CENTRDBINSTANCE_NT_ADA SyCheckHostnameLookup 2 333 offical host name for 'Karthikeyan' is 'Karthikeyan'. Info: CENTRDBINSTANCE_NT_ADA SyCheckHostnameLookup 2 333 host 'Karthikeyan' has ip address '115.184.71.93' Info: CENTRDBINSTANCE_NT_ADA SyCheckHostnameLookup 2 333 offical host name for '115.184.71.93' is 'Karthikeyan'. Info: CENTRDBINSTANCE_NT_ADA SyCheckHostnameLookup 2 333 checking host name lookup for 'Karthikeyan' Info: CENTRDBINSTANCE_NT_ADA SyCheckHostnameLookup 2 333 offical host name for 'Karthikeyan' is 'Karthikeyan'. Info: CENTRDBINSTANCE_NT_ADA SyCheckHostnameLookup 2 333 host 'Karthikeyan' has ip address '115.184.71.93' Info: CENTRDBINSTANCE_NT_ADA SyCheckHostnameLookup 2 333 offical host name for '115.184.71.93' is 'Karthikeyan'. Error: CommandFileController StoreMasterTableFromCommandFile 2 99 Command file could not be opened. Error: CommandFileController SetKeytableForSect 2 99 CommandFile could not be updated Warning: ADADBINSTANCE_IND_ADA GetConfirmationFor 2 58 Cleanup database instance BSP for new installation. Error: CommandFileController StoreMasterTableFromCommandFile 2 58 Command file could not be opened. Error: CommandFileController SetKeytableForSect 2 58 CommandFile could not be updated Error: CommandFileController StoreMasterTableFromCommandFile 2 333 Command file could not be opened. Error: CommandFileController SetKeytableForSect 2 333 CommandFile could not be updated Error: CommandFileController StoreMasterTableFromCommandFile 2 1206 Command file could not be opened. Error: CommandFileController SetKeytableForSect 2 1206 CommandFile could not be updated Error: CommandFileController StoreMasterTableFromCommandFile 2 75 Command file could not be opened. Error: CommandFileController SetKeytableForSect 2 75 CommandFile could not be updated Error: CommandFileController StoreMasterTableFromCommandFile 2 247 Command file could not be opened. Error: CommandFileController SetKeytableForSect 2 247 CommandFile could not be updated Error: CommandFileController StoreMasterTableFromCommandFile 2 1195 Command file could not be opened. Error: CommandFileController SetKeytableForSect 2 1195 CommandFile could not be updated Error: CommandFileController StoreMasterTableFromCommandFile 2 1195 Command file could not be opened. Error: CommandFileController SetKeytableForSect 2 1195 CommandFile could not be updated Error: CommandFileController StoreMasterTableFromCommandFile 2 120 Command file could not be opened. Error: CommandFileController SetKeytableForSect 2 120 CommandFile could not be updated Error: CommandFileController StoreMasterTableFromCommandFile 2 816 Command file could not be opened. Error: CommandFileController SetKeytableForSect 2 816 CommandFile could not be updated Error: CommandFileController StoreMasterTableFromCommandFile 2 242 Command file could not be opened. Error: CommandFileController SetKeytableForSect 2 242 CommandFile could not be updated Error: CommandFileController StoreMasterTableFromCommandFile 2 816 Command file could not be opened. Error: CommandFileController SetKeytableForSect 2 816 CommandFile could not be updated Error: CommandFileController StoreMasterTableFromCommandFile 2 816 Command file could not be opened. Error: CommandFileController SetKeytableForSect 2 816 CommandFile could not be updated Error: CommandFileController StoreMasterTableFromCommandFile 2 816 Command file could not be opened. Error: CommandFileController SetKeytableForSect 2 816 CommandFile could not be updated Error: CommandFileController StoreMasterTableFromCommandFile 2 815 Command file could not be opened. Error: CommandFileController SetKeytableForSect 2 815 CommandFile could not be updated Error: CommandFileController StoreMasterTableFromCommandFile 2 223 Command file could not be opened. Error: CommandFileController SetKeytableForSect 2 223 CommandFile could not be updated Error: CommandFileController StoreMasterTableFromCommandFile 2 1 Command file could not be opened. Error: CommandFileController SetKeytableForSect 2 1 CommandFile could not be updated Error: CommandFileController StoreMasterTableFromCommandFile 2 10 Command file could not be opened. Error: CommandFileController SetKeytableForSect 2 10 CommandFile could not be updated Error: CommandFileController StoreMasterTableFromCommandFile 2 263 Command file could not be opened. Error: CommandFileController SetKeytableForSect 2 263 CommandFile could not be updated Error: CommandFileController StoreMasterTableFromCommandFile 2 263 Command file could not be opened. Error: CommandFileController SetKeytableForSect 2 263 CommandFile could not be updated Error: CommandFileController StoreMasterTableFromCommandFile 2 263 Command file could not be opened. Error: CommandFileController SetKeytableForSect 2 263 CommandFile could not be updated Error: CommandFileController StoreMasterTableFromCommandFile 2 760 Command file could not be opened. Error: CommandFileController SetKeytableForSect 2 760 CommandFile could not be updated Error: CommandFileController StoreMasterTableFromCommandFile 2 1267 Command file could not be opened. Error: CommandFileController SetKeytableForSect 2 1267 CommandFile could not be updated Error: CommandFileController StoreMasterTableFromCommandFile 2 1111 Command file could not be opened. Error: CommandFileController SetKeytableForSect 2 1111 CommandFile could not be updated Error: CommandFileController StoreMasterTableFromCommandFile 2 1122 Command file could not be opened. Error: CommandFileController SetKeytableForSect 2 1122 CommandFile could not be updated Error: CommandFileController StoreMasterTableFromCommandFile 2 1114 Command file could not be opened. Error: CommandFileController SetKeytableForSect 2 1114 CommandFile could not be updated Error: CommandFileController StoreMasterTableFromCommandFile 2 1 Command file could not be opened. Error: CommandFileController SetKeytableForSect 2 1 CommandFile could not be updated Error: CommandFileController StoreMasterTableFromCommandFile 2 1 Command file could not be opened. Error: CommandFileController SetKeytableForSect 2 1 CommandFile could not be updated Error: CommandFileController StoreMasterTableFromCommandFile 2 54 Command file could not be opened. Error: CommandFileController SetKeytableForSect 2 54 CommandFile could not be updated Error: CommandFileController StoreMasterTableFromCommandFile 2 1146 Command file could not be opened. Error: CommandFileController SetKeytableForSect 2 1146 CommandFile could not be updated Error: CommandFileController StoreMasterTableFromCommandFile 2 718 Command file could not be opened. Error: CommandFileController SetKeytableForSect 2 718 CommandFile could not be updated Error: CommandFileController StoreMasterTableFromCommandFile 2 760 Command file could not be opened. Error: CommandFileController SetKeytableForSect 2 760 CommandFile could not be updated Error: CommandFileController StoreMasterTableFromCommandFile 2 1 Command file could not be opened. Error: CommandFileController SetKeytableForSect 2 1 CommandFile could not be updated Info: InstController MakeStepsDeliver 2 333 Requesting Installation Details Error: CommandFileController StoreMasterTableFromCommandFile 2 333 Command file could not be opened. Error: CommandFileController SetKeytableForSect 2 333 CommandFile could not be updated Error: CommandFileController StoreMasterTableFromCommandFile 2 333 Command file could not be opened. Error: CommandFileController SetKeytableForSect 2 333 CommandFile could not be updated Info: CDSERVERBASE InternalWarmKeyCheck 2 309 The CD KERNEL will not be copied. Info: CDSERVERBASE InternalWarmKeyCheck 2 309 The CD DATA1 will not be copied. Info: CDSERVERBASE InternalWarmKeyCheck 2 309 The CD DATA2 will not be copied. Info: InstController MakeStepsDeliver 2 309 Requesting Information on CD-ROMs Error: CommandFileController StoreMasterTableFromCommandFile 2 309 Command file could not be opened. Error: CommandFileController SetKeytableForSect 2 309 CommandFile could not be updated Error: CommandFileController StoreMasterTableFromCommandFile 2 309 Command file could not be opened. Error: CommandFileController SetKeytableForSect 2 309 CommandFile could not be updated Info: CENTRDBINSTANCE_NT_ADA InternalWarmKeyCheck 2 333 The installation phase is starting now. Please look in the log file for further information about current actions. Info: InstController MakeStepsDeliver 2 333 Requesting Installation Details Error: CommandFileController StoreMasterTableFromCommandFile 2 333 Command file could not be opened. Error: CommandFileController SetKeytableForSect 2 333 CommandFile could not be updated Error: CommandFileController StoreMasterTableFromCommandFile 2 333 Command file could not be opened. Error: CommandFileController SetKeytableForSect 2 333 CommandFile could not be updated Info: InstController MakeStepsDeliver 2 99 Defining Key Values Error: CommandFileController StoreMasterTableFromCommandFile 2 99 Command file could not be opened. Error: CommandFileController SetKeytableForSect 2 99 CommandFile could not be updated Error: CommandFileController StoreMasterTableFromCommandFile 2 99 Command file could not be opened. Error: CommandFileController SetKeytableForSect 2 99 CommandFile could not be updated Info: InstController MakeStepsDeliver 2 58 Requesting Setup Details Error: CommandFileController StoreMasterTableFromCommandFile 2 58 Command file could not be opened. Error: CommandFileController SetKeytableForSect 2 58 CommandFile could not be updated Error: CommandFileController StoreMasterTableFromCommandFile 2 58 Command file could not be opened. Error: CommandFileController SetKeytableForSect 2 58 CommandFile could not be updated Info: InstController MakeStepsDeliver 2 333 Requesting Installation Details Error: CommandFileController StoreMasterTableFromCommandFile 2 333 Command file could not be opened. Error: CommandFileController SetKeytableForSect 2 333 CommandFile could not be updated Error: CommandFileController StoreMasterTableFromCommandFile 2 333 Command file could not be opened. Error: CommandFileController SetKeytableForSect 2 333 CommandFile could not be updated Info: InstController MakeStepsDeliver 2 1206 Setting Users for Single DB landscape Error: CommandFileController StoreMasterTableFromCommandFile 2 1206 Command file could not be opened. Error: CommandFileController SetKeytableForSect 2 1206 CommandFile could not be updated Error: CommandFileController StoreMasterTableFromCommandFile 2 1206 Command file could not be opened. Error: CommandFileController SetKeytableForSect 2 1206 CommandFile could not be updated Info: InstController MakeStepsDeliver 2 75 Stopping the SAP DB Instance Error: CommandFileController StoreMasterTableFromCommandFile 2 75 Command file could not be opened. Error: CommandFileController SetKeytableForSect 2 75 CommandFile could not be updated Error: CommandFileController StoreMasterTableFromCommandFile 2 75 Command file could not be opened. Error: CommandFileController SetKeytableForSect 2 75 CommandFile could not be updated Info: InstController MakeStepsDeliver 2 247 Stopping the SAP DB remote server Error: CommandFileController StoreMasterTableFromCommandFile 2 247 Command file could not be opened. Error: CommandFileController SetKeytableForSect 2 247 CommandFile could not be updated Error: CommandFileController StoreMasterTableFromCommandFile 2 247 Command file could not be opened. Error: CommandFileController SetKeytableForSect 2 247 CommandFile could not be updated Warning: CDSERVERBASE ConfirmKey 2 1195 Can not read from Z:. Please ensure this path is accessible. Info: LvKeyRequest For further information see HTML documentation: step: SAPDBSETCDPATH_IND_IND and key: KERNEL_LOCATION Info: InstController MakeStepsDeliver 2 1195 Installing SAP DB Software Error: CommandFileController StoreMasterTableFromCommandFile 2 1195 Command file could not be opened. Error: CommandFileController SetKeytableForSect 2 1195 CommandFile could not be updated Error: CommandFileController StoreMasterTableFromCommandFile 2 1195 Command file could not be opened. Error: CommandFileController SetKeytableForSect 2 1195 CommandFile could not be updated Info: InstController MakeStepsDeliver 2 1195 Installing SAP DB Software Info: SAPDBINSTALL_IND_ADA SyCoprocessCreate 2 1195 Creating coprocess E:\sapdb\NT\I386\sdbinst.exe ... Info: SAPDBINSTALL_IND_ADA ExecuteDo 2 1195 RC code form SyCoprocessWait = 0 . Error: CommandFileController StoreMasterTableFromCommandFile 2 1195 Command file could not be opened. Error: CommandFileController SetKeytableForSect 2 1195 CommandFile could not be updated Error: CommandFileController StoreMasterTableFromCommandFile 2 1195 Command file could not be opened. Error: CommandFileController SetKeytableForSect 2 1195 CommandFile could not be updated Info: InstController MakeStepsDeliver 2 120 Extracting SAP DB Tools Software Info: ADAEXTRACTLCTOOLS_NT_ADA SyCoprocessCreate 2 120 Creating coprocess SAPCAR ... Info: ADAEXTRACTLCTOOLS_NT_ADA SyCoprocessCreate 2 120 Creating coprocess SAPCAR ... Error: CommandFileController StoreMasterTableFromCommandFile 2 120 Command file could not be opened. Error: CommandFileController SetKeytableForSect 2 120 CommandFile could not be updated Error: CommandFileController StoreMasterTableFromCommandFile 2 120 Command file could not be opened. Error: CommandFileController SetKeytableForSect 2 120 CommandFile could not be updated Info: InstController MakeStepsDeliver 2 816 Extracting the Database-Dependent SAP system Executables Info: ADAEXTRACTBSPCFG SyCoprocessCreate 2 816 Creating coprocess SAPCAR ... Info: ADAEXTRACTBSPCFG SyCoprocessCreate 2 816 Creating coprocess SAPCAR ... Error: CommandFileController StoreMasterTableFromCommandFile 2 816 Command file could not be opened. Error: CommandFileController SetKeytableForSect 2 816 CommandFile could not be updated Error: CommandFileController StoreMasterTableFromCommandFile 2 816 Command file could not be opened. Error: CommandFileController SetKeytableForSect 2 816 CommandFile could not be updated Info: InstController MakeStepsDeliver 2 242 Starting VSERVER Info: ADAXSERVER_NT_ADA SyCoprocessCreate 2 242 Creating coprocess C:\sapdb\programs\bin\x_server.exe ... Info: ADAXSERVER_NT_ADA ExecuteDo 2 242 RC code form SyCoprocessWait = 0 . Error: CommandFileController StoreMasterTableFromCommandFile 2 242 Command file could not be opened. Error: CommandFileController SetKeytableForSect 2 242 CommandFile could not be updated Error: CommandFileController StoreMasterTableFromCommandFile 2 242 Command file could not be opened. Error: CommandFileController SetKeytableForSect 2 242 CommandFile could not be updated Info: InstController MakeStepsDeliver 2 816 Extracting the Database-Dependent SAP system Executables Info: EXTRACTSAPEXEDBDATA1 SyCoprocessCreate 2 816 Creating coprocess SAPCAR ... Info: EXTRACTSAPEXEDBDATA1 SyCoprocessCreate 2 816 Creating coprocess SAPCAR ... Error: CommandFileController StoreMasterTableFromCommandFile 2 816 Command file could not be opened. Error: CommandFileController SetKeytableForSect 2 816 CommandFile could not be updated Error: CommandFileController StoreMasterTableFromCommandFile 2 816 Command file could not be opened. Error: CommandFileController SetKeytableForSect 2 816 CommandFile could not be updated Warning: CDSERVERBASE ConfirmKey 2 816 Can not read from Y:. Please ensure this path is accessible. Info: LvKeyRequest For further information see HTML documentation: step: EXTRACTSAPEXEDBDATA2 and key: DATA1_LOCATION Info: InstController MakeStepsDeliver 2 816 Extracting the Database-Dependent SAP system Executables Info: EXTRACTSAPEXEDBDATA2 SyCoprocessCreate 2 816 Creating coprocess SAPCAR ... Info: EXTRACTSAPEXEDBDATA2 SyCoprocessCreate 2 816 Creating coprocess SAPCAR ... Error: CommandFileController StoreMasterTableFromCommandFile 2 816 Command file could not be opened. Error: CommandFileController SetKeytableForSect 2 816 CommandFile could not be updated Error: CommandFileController StoreMasterTableFromCommandFile 2 816 Command file could not be opened. Error: CommandFileController SetKeytableForSect 2 816 CommandFile could not be updated Warning: CDSERVERBASE ConfirmKey 2 816 Can not read from X:. Please ensure this path is accessible. Info: LvKeyRequest For further information see HTML documentation: step: EXTRACTSAPEXEDBDATA3 and key: DATA2_LOCATION Info: InstController MakeStepsDeliver 2 816 Extracting the Database-Dependent SAP system Executables Info: EXTRACTSAPEXEDBDATA3 SyCoprocessCreate 2 816 Creating coprocess SAPCAR ... Info: EXTRACTSAPEXEDBDATA3 SyCoprocessCreate 2 816 Creating coprocess SAPCAR ... Error: CommandFileController StoreMasterTableFromCommandFile 2 816 Command file could not be opened. Error: CommandFileController SetKeytableForSect 2 816 CommandFile could not be updated Error: CommandFileController StoreMasterTableFromCommandFile 2 816 Command file could not be opened. Error: CommandFileController SetKeytableForSect 2 816 CommandFile could not be updated Warning: CDSERVERBASE ConfirmKey 2 815 We tried to find the label SAPDB:MINI-WAS-DEMO:620:KERNEL for CD KERNEL in path E:. But the check was not successfull. Info: LvKeyRequest For further information see HTML documentation: step: EXTRACTSAPEXE and key: KERNEL_LOCATION Info: InstController MakeStepsDeliver 2 815 Extracting the SAP Executables Info: EXTRACTSAPEXE SyCoprocessCreate 2 815 Creating coprocess SAPCAR ... Info: EXTRACTSAPEXE SyCoprocessCreate 2 815 Creating coprocess SAPCAR ... Error: CommandFileController StoreMasterTableFromCommandFile 2 815 Command file could not be opened. Error: CommandFileController SetKeytableForSect 2 815 CommandFile could not be updated Error: CommandFileController StoreMasterTableFromCommandFile 2 815 Command file could not be opened. Error: CommandFileController SetKeytableForSect 2 815 CommandFile could not be updated Info: InstController MakeStepsDeliver 2 223 Setting new Rundirectory. Info: ADADBREGISTER_IND_ADA SyCoprocessCreate 2 223 Creating coprocess C:\sapdb\programs\pgm\dbmcli.exe ... Info: ADADBREGISTER_IND_ADA ExecuteDo 2 223 RC code form SyCoprocessWait = 0 . Error: CommandFileController StoreMasterTableFromCommandFile 2 223 Command file could not be opened. Error: CommandFileController SetKeytableForSect 2 223 CommandFile could not be updated Error: CommandFileController StoreMasterTableFromCommandFile 2 223 Command file could not be opened. Error: CommandFileController SetKeytableForSect 2 223 CommandFile could not be updated Info: InstController MakeStepsDeliver 2 1 ADASETDEVSPACES_IND_ADA Error: CommandFileController StoreMasterTableFromCommandFile 2 1 Command file could not be opened. Error: CommandFileController SetKeytableForSect 2 1 CommandFile could not be updated Error: CommandFileController StoreMasterTableFromCommandFile 2 1 Command file could not be opened. Error: CommandFileController SetKeytableForSect 2 1 CommandFile could not be updated Info: InstController MakeStepsDeliver 2 10 Performing Service BCHECK Error: CommandFileController StoreMasterTableFromCommandFile 2 10 Command file could not be opened. Error: CommandFileController SetKeytableForSect 2 10 CommandFile could not be updated Error: CommandFileController StoreMasterTableFromCommandFile 2 10 Command file could not be opened. Error: CommandFileController SetKeytableForSect 2 10 CommandFile could not be updated Info: InstController MakeStepsDeliver 2 263 Creating XUSER File for the User ADM for Dialog Instance Info: ADAXUSERSIDADM_DEFAULT_NT_ADA SyCoprocessCreate 2 263 Creating coprocess C:\sapdb\programs\pgm\dbmcli.exe ... Info: ADAXUSERSIDADM_DEFAULT_NT_ADA ExecuteDo 2 263 RC code form SyCoprocessWait = 0 . Error: CommandFileController StoreMasterTableFromCommandFile 2 263 Command file could not be opened. Error: CommandFileController SetKeytableForSect 2 263 CommandFile could not be updated Error: CommandFileController StoreMasterTableFromCommandFile 2 263 Command file could not be opened. Error: CommandFileController SetKeytableForSect 2 263 CommandFile could not be updated Info: InstController MakeStepsDeliver 2 263 Creating XUSER File for the User ADM for Dialog Instance Info: ADAXUSERSIDADM_COLD_NT_ADA SyCoprocessCreate 2 263 Creating coprocess C:\sapdb\programs\pgm\dbmcli.exe ... Info: ADAXUSERSIDADM_COLD_NT_ADA ExecuteDo 2 263 RC code form SyCoprocessWait = 0 . Error: CommandFileController StoreMasterTableFromCommandFile 2 263 Command file could not be opened. Error: CommandFileController SetKeytableForSect 2 263 CommandFile could not be updated Error: CommandFileController StoreMasterTableFromCommandFile 2 263 Command file could not be opened. Error: CommandFileController SetKeytableForSect 2 263 CommandFile could not be updated Info: InstController MakeStepsDeliver 2 263 Creating XUSER File for the User ADM for Dialog Instance Info: ADAXUSERSIDADM_WARM_NT_ADA SyCoprocessCreate 2 263 Creating coprocess C:\sapdb\programs\pgm\dbmcli.exe ... Info: ADAXUSERSIDADM_WARM_NT_ADA ExecuteDo 2 263 RC code form SyCoprocessWait = 0 . Error: CommandFileController StoreMasterTableFromCommandFile 2 263 Command file could not be opened. Error: CommandFileController SetKeytableForSect 2 263 CommandFile could not be updated Error: CommandFileController StoreMasterTableFromCommandFile 2 263 Command file could not be opened. Error: CommandFileController SetKeytableForSect 2 263 CommandFile could not be updated Info: InstController MakeStepsDeliver 2 760 Creating the Default Profile Info: DEFAULTPROFILE_IND_IND SyFileVersionSave 2 760 Saving original content of file C:\MiniWAS\DEFAULT.PFL ... Error: CommandFileController StoreMasterTableFromCommandFile 2 760 Command file could not be opened. Error: CommandFileController SetKeytableForSect 2 760 CommandFile could not be updated Error: CommandFileController StoreMasterTableFromCommandFile 2 760 Command file could not be opened. Error: CommandFileController SetKeytableForSect 2 760 CommandFile could not be updated Info: InstController MakeStepsDeliver 2 1267 Modifying or Creating the TPPARAM File Info: TPPARAMMODIFY_NT_ADA SyFileVersionSave 2 1267 Saving original content of file C:\MiniWAS\trans\bin\TPPARAM ... Error: CommandFileController StoreMasterTableFromCommandFile 2 1267 Command file could not be opened. Error: CommandFileController SetKeytableForSect 2 1267 CommandFile could not be updated Error: CommandFileController StoreMasterTableFromCommandFile 2 1267 Command file could not be opened. Error: CommandFileController SetKeytableForSect 2 1267 CommandFile could not be updated Info: InstController MakeStepsDeliver 2 1111 Creating the Service Entry for the Dispatcher Info: R3DISPATCHERPORT_IND_IND IaServicePortAppend 2 1111 Checking service name sapdp00, protocol tcp, port number 3200 ... Info: R3DISPATCHERPORT_IND_IND IaServicePortAppend 2 1111 Port name sapdp00 is known and the port number 3200 is equal to the existing port number 3200 Error: CommandFileController StoreMasterTableFromCommandFile 2 1111 Command file could not be opened. Error: CommandFileController SetKeytableForSect 2 1111 CommandFile could not be updated Error: CommandFileController StoreMasterTableFromCommandFile 2 1111 Command file could not be opened. Error: CommandFileController SetKeytableForSect 2 1111 CommandFile could not be updated Info: InstController MakeStepsDeliver 2 1122 Creating the Service Entry for the Message Server Info: R3MESSAGEPORT_IND_IND IaServicePortAppend 2 1122 Checking service name sapmsBSP, protocol tcp, port number 3600 ... Info: R3MESSAGEPORT_IND_IND IaServicePortAppend 2 1122 Port name sapmsBSP is known and the port number 3600 is equal to the existing port number 3600 Error: CommandFileController StoreMasterTableFromCommandFile 2 1122 Command file could not be opened. Error: CommandFileController SetKeytableForSect 2 1122 CommandFile could not be updated Error: CommandFileController StoreMasterTableFromCommandFile 2 1122 Command file could not be opened. Error: CommandFileController SetKeytableForSect 2 1122 CommandFile could not be updated Info: InstController MakeStepsDeliver 2 1114 Creating the Service Entry for the Gateway Service Info: R3GATEWAYPORT_IND_IND IaServicePortAppend 2 1114 Checking service name sapgw00, protocol tcp, port number 3300 ... Info: R3GATEWAYPORT_IND_IND IaServicePortAppend 2 1114 Port name sapgw00 is known and the port number 3300 is equal to the existing port number 3300 Error: CommandFileController StoreMasterTableFromCommandFile 2 1114 Command file could not be opened. Error: CommandFileController SetKeytableForSect 2 1114 CommandFile could not be updated Error: CommandFileController StoreMasterTableFromCommandFile 2 1114 Command file could not be opened. Error: CommandFileController SetKeytableForSect 2 1114 CommandFile could not be updated Info: InstController MakeStepsDeliver 2 1 PISTARTBSP Info: PISTARTBSP SyDirCreate 2 1 Checking existence of directory C:\Users\Karthikeyan\Desktop. If it does not exist creating it with user , group and permission 0 ... Error: CommandFileController StoreMasterTableFromCommandFile 2 1 Command file could not be opened. Error: CommandFileController SetKeytableForSect 2 1 CommandFile could not be updated Error: CommandFileController StoreMasterTableFromCommandFile 2 1 Command file could not be opened. Error: CommandFileController SetKeytableForSect 2 1 CommandFile could not be updated Info: InstController MakeStepsDeliver 2 1 PISTARTBSPGROUP Info: PISTARTBSPGROUP SyDirCreate 2 1 Checking existence of directory C:\Users\Karthikeyan\AppData\Roaming\Microsoft\Windows\Start Menu\Programs\Mini SAP Web Application Server. If it does not exist creating it with user , group and permission 0 ... Error: CommandFileController StoreMasterTableFromCommandFile 2 1 Command file could not be opened. Error: CommandFileController SetKeytableForSect 2 1 CommandFile could not be updated Error: CommandFileController StoreMasterTableFromCommandFile 2 1 Command file could not be opened. Error: CommandFileController SetKeytableForSect 2 1 CommandFile could not be updated Info: InstController MakeStepsDeliver 2 54 Starting SAP DB to Mode WARM Error: Command

  Read the article

• Interesting issue with WCF wsHttpBinding through a Firewall

  - by Marko

  I have a web application deployed in an internet hosting provider. This web application consumes a WCF Service deployed at an IIS server located at my company’s application server, in order to have data access to the company’s database, the network guys allowed me to expose this WCF service through a firewall for security reasons. A diagram would look like this. [Hosted page] --- (Internet) --- |Firewall <Public IP>:<Port-X >| --- [IIS with WCF Service <Comp. Network Ip>:<Port-Y>] link text I also wanted to use wsHttpBinding to take advantage of its security features, and encrypt sensible information. After trying it out I get the following error: Exception Details: System.ServiceModel.EndpointNotFoundException: The message with To 'http://<IP>:<Port>/service/WCFService.svc' cannot be processed at the receiver, due to an AddressFilter mismatch at the EndpointDispatcher. Check that the sender and receiver's EndpointAddresses agree. Doing some research I found out that wsHttpBinding uses WS-Addressing standards, and reading about this standard I learned that the SOAP header is enhanced to include tags like ‘MessageID’, ‘ReplyTo’, ‘Action’ and ‘To’. So I’m guessing that, because the client application endpoint specifies the Firewall IP address and Port, and the service replies with its internal network address which is different from the Firewall’s IP, then WS-Addressing fires the above message. Which I think it’s a very good security measure, but it’s not quite useful in my scenario. Quoting the WS-Addressing standard submission (http://www.w3.org/Submission/ws-addressing/) "Due to the range of network technologies currently in wide-spread use (e.g., NAT, DHCP, firewalls), many deployments cannot assign a meaningful global URI to a given endpoint. To allow these ‘anonymous’ endpoints to initiate message exchange patterns and receive replies, WS-Addressing defines the following well-known URI for use by endpoints that cannot have a stable, resolvable URI. http://schemas.xmlsoap.org/ws/2004/08/addressing/role/anonymous" HOW can I configure my wsHttpBinding Endpoint to address my Firewall’s IP and to ignore or bypass the address specified in the ‘To’ WS-Addressing tag in the SOAP message header? Or do I have to change something in my service endpoint configuration? Help and guidance will be much appreciated. Marko. P.S.: While I find any solution to this, I’m using basicHttpBinding with absolutely no problem of course.

  Read the article

• Python 2.7 - Help using an API (HL7)

  - by atomicluis

  I am new to programming and Python. I have a very basic python script that connects to server and send a text message: #!/usr/bin/python import socket s = socket.socket() host = '127.0.0.1' port = 4106 s.connect((host, port)) message = 'test1' s.send(message) print s.recv(1024) s.close Everything is fine, except that this message is an HL7 message and needs to wrapped in MLLP I found this API that I think can do this for me (http://python-hl7.readthedocs.org/en/latest/api.html#mllp-network-client) So I modified my program to the following, but I keep getting the error message: NameError: name 'MLLPClient' is not defined #!/usr/bin/python import socket import hl7 host = '127.0.0.1' port = 4106 with MLLPClient(host, port) as client: client.send_message('test1') print s.recv(1024) s.close Thanks in advanced for all the help

  Read the article

• WCF binding programatically and adding metadata excange

  - by totem

  Hi, My problem is im trying to enable mex on a service that uses net.tcp binding. that binding is for localhost port 5000, when i want to enable mex on the same port, and have it avilable for http i have to enable the HttpGetEnabled on the Service host. All this works well but when i try to add the binding it fails becuase the binding is "net.tcp://localhost:5000/test". is there a way to enable mex on the same port but with a diffrent uri? Without enableing NetTcpPortSharing. I dont think the code is the issue since i can add the MEX on a diffrent port through the code an it works fine, the question is how to have net.tcp://localhost:5000/test as the WCF tcp based enpoint and net.tcp://localhost:5000/test/mex as the http mex endpoint that gives the WSDL for the TCP endpoint. thanks, Totem

  Read the article

• BasicHTTPServer, SimpleHTTPServer and concurrency

  - by braindump

  I'm writing a small web server for testing purposes using python, BasicHTTPServer and SimpleHTTPServer. It looks like it's processing one request at a time. Is there any way to make it a little faster without messing around too deeply? Basicly my code looks as the following and I'd like to keep it this simple ;) os.chdir(webroot) httpd = BaseHTTPServer.HTTPServer(("", port), SimpleHTTPServer.SimpleHTTPRequestHandler) print("Serving directory %s on port %i" %(webroot, port) ) try: httpd.serve_forever() except KeyboardInterrupt: print("Server stopped.")

  Read the article

• DHCP reply packets do not make it into KVM instance in OpenStack

  - by Lorin Hochstein

  I'm running a KVM instance inside of OpenStack, and it isn't getting an IP address from the DHCP server. Using tcpdump, I can see the request and reply packets on vnet0 of the compute host: # tcpdump -i vnet0 -n port 67 or port 68 tcpdump: WARNING: vnet0: no IPv4 address assigned tcpdump: verbose output suppressed, use -v or -vv for full protocol decode listening on vnet0, link-type EN10MB (Ethernet), capture size 65535 bytes 19:44:56.176727 IP 0.0.0.0.68 > 255.255.255.255.67: BOOTP/DHCP, Request from fa:16:3e:46:f6:11, length 300 19:44:56.176785 IP 0.0.0.0.68 > 255.255.255.255.67: BOOTP/DHCP, Request from fa:16:3e:46:f6:11, length 300 19:44:56.177315 IP 10.40.0.1.67 > 10.40.0.3.68: BOOTP/DHCP, Reply, length 319 19:45:02.179834 IP 0.0.0.0.68 > 255.255.255.255.67: BOOTP/DHCP, Request from fa:16:3e:46:f6:11, length 300 19:45:02.179904 IP 0.0.0.0.68 > 255.255.255.255.67: BOOTP/DHCP, Request from fa:16:3e:46:f6:11, length 300 19:45:02.180375 IP 10.40.0.1.67 > 10.40.0.3.68: BOOTP/DHCP, Reply, length 319 However, if I do the same thing on eth0 inside the KVM instance, I only see the request packets, not the reply packets. What would prevent the packets from making it from vnet0 of the host to eth0 of the guest? My host is running Ubuntu 12.04 and my guest is running CentOS 6.3. Note that I have added this rule in my iptables, but it doesn't resolve the issue: -A POSTROUTING -p udp -m udp --dport 68 -j CHECKSUM --checksum-fill The instance corresponds to vnet0 and is connected via br100: # brctl show bridge name bridge id STP enabled interfaces br100 8000.54781a8605f2 no eth1 vnet0 vnet1 virbr0 8000.000000000000 yes Here's the full iptables-save: # Generated by iptables-save v1.4.12 on Tue Apr 2 19:47:27 2013 *nat :PREROUTING ACCEPT [8323:2553683] :INPUT ACCEPT [7993:2494942] :OUTPUT ACCEPT [6158:461050] :POSTROUTING ACCEPT [6455:511595] :nova-compute-OUTPUT - [0:0] :nova-compute-POSTROUTING - [0:0] :nova-compute-PREROUTING - [0:0] :nova-compute-float-snat - [0:0] :nova-compute-snat - [0:0] :nova-postrouting-bottom - [0:0] -A PREROUTING -j nova-compute-PREROUTING -A OUTPUT -j nova-compute-OUTPUT -A POSTROUTING -j nova-compute-POSTROUTING -A POSTROUTING -j nova-postrouting-bottom -A POSTROUTING -s 192.168.122.0/24 ! -d 192.168.122.0/24 -p tcp -j MASQUERADE --to-ports 1024-65535 -A POSTROUTING -s 192.168.122.0/24 ! -d 192.168.122.0/24 -p udp -j MASQUERADE --to-ports 1024-65535 -A POSTROUTING -s 192.168.122.0/24 ! -d 192.168.122.0/24 -j MASQUERADE -A nova-compute-snat -j nova-compute-float-snat -A nova-postrouting-bottom -j nova-compute-snat COMMIT # Completed on Tue Apr 2 19:47:27 2013 # Generated by iptables-save v1.4.12 on Tue Apr 2 19:47:27 2013 *mangle :PREROUTING ACCEPT [7969:5385812] :INPUT ACCEPT [7905:5363718] :FORWARD ACCEPT [158:48190] :OUTPUT ACCEPT [6877:8647975] :POSTROUTING ACCEPT [7035:8696165] -A POSTROUTING -o virbr0 -p udp -m udp --dport 68 -j CHECKSUM --checksum-fill -A POSTROUTING -p udp -m udp --dport 68 -j CHECKSUM --checksum-fill COMMIT # Completed on Tue Apr 2 19:47:27 2013 # Generated by iptables-save v1.4.12 on Tue Apr 2 19:47:27 2013 *filter :INPUT ACCEPT [2196774:15856921923] :FORWARD ACCEPT [0:0] :OUTPUT ACCEPT [2447201:1170227646] :nova-compute-FORWARD - [0:0] :nova-compute-INPUT - [0:0] :nova-compute-OUTPUT - [0:0] :nova-compute-inst-19 - [0:0] :nova-compute-inst-20 - [0:0] :nova-compute-local - [0:0] :nova-compute-provider - [0:0] :nova-compute-sg-fallback - [0:0] :nova-filter-top - [0:0] -A INPUT -j nova-compute-INPUT -A INPUT -i virbr0 -p udp -m udp --dport 53 -j ACCEPT -A INPUT -i virbr0 -p tcp -m tcp --dport 53 -j ACCEPT -A INPUT -i virbr0 -p udp -m udp --dport 67 -j ACCEPT -A INPUT -i virbr0 -p tcp -m tcp --dport 67 -j ACCEPT -A FORWARD -j nova-filter-top -A FORWARD -j nova-compute-FORWARD -A FORWARD -d 192.168.122.0/24 -o virbr0 -m state --state RELATED,ESTABLISHED -j ACCEPT -A FORWARD -s 192.168.122.0/24 -i virbr0 -j ACCEPT -A FORWARD -i virbr0 -o virbr0 -j ACCEPT -A FORWARD -o virbr0 -j REJECT --reject-with icmp-port-unreachable -A FORWARD -i virbr0 -j REJECT --reject-with icmp-port-unreachable -A OUTPUT -j nova-filter-top -A OUTPUT -j nova-compute-OUTPUT -A nova-compute-FORWARD -i br100 -j ACCEPT -A nova-compute-FORWARD -o br100 -j ACCEPT -A nova-compute-inst-19 -m state --state INVALID -j DROP -A nova-compute-inst-19 -m state --state RELATED,ESTABLISHED -j ACCEPT -A nova-compute-inst-19 -j nova-compute-provider -A nova-compute-inst-19 -s 10.40.0.1/32 -p udp -m udp --sport 67 --dport 68 -j ACCEPT -A nova-compute-inst-19 -s 10.40.0.0/16 -j ACCEPT -A nova-compute-inst-19 -p tcp -m tcp --dport 22 -j ACCEPT -A nova-compute-inst-19 -p icmp -j ACCEPT -A nova-compute-inst-19 -j nova-compute-sg-fallback -A nova-compute-inst-20 -m state --state INVALID -j DROP -A nova-compute-inst-20 -m state --state RELATED,ESTABLISHED -j ACCEPT -A nova-compute-inst-20 -j nova-compute-provider -A nova-compute-inst-20 -s 10.40.0.1/32 -p udp -m udp --sport 67 --dport 68 -j ACCEPT -A nova-compute-inst-20 -s 10.40.0.0/16 -j ACCEPT -A nova-compute-inst-20 -p tcp -m tcp --dport 22 -j ACCEPT -A nova-compute-inst-20 -p icmp -j ACCEPT -A nova-compute-inst-20 -j nova-compute-sg-fallback -A nova-compute-local -d 10.40.0.3/32 -j nova-compute-inst-19 -A nova-compute-local -d 10.40.0.4/32 -j nova-compute-inst-20 -A nova-compute-sg-fallback -j DROP -A nova-filter-top -j nova-compute-local COMMIT # Completed on Tue Apr 2 19:47:27 2013

  Read the article

• which ASP.NET hosting site allows listening on different ports than 80 and uses .NET 4?

  - by ijjo

  I'm trying to take advantage of HTML 5 web sockets in .NET and the easiest way appears to be something like what this guy does. I've already tested this myself and it works great, but there are a few problems if I try to deploy this to my hosting site (discountasp.net). Basically, I am not allowed to open up a port on 8080 and listen on it. I then tried to figure out a way to listen on port 80 with IIS as well, but using the HTTPListener, I run into sercurity issues as well. This doesn't seem like it will help since I can't mess with this stuff on the hosting site server either. So to make my life easier, I think I need to find a hosting site that simply allows me to open up a socket on port 8080 and listen on it. Anyone know of one? Or does anyone know of a workaround (besides sniffing all the traffic on port 80)?

  Read the article

• Websockify to wrap a forking server

  - by Gurjeet Singh

  I came across Websockify [1] and the accompanying Websock client-side javascript library. AIUI from the Wrap a Programsection in README, Websockify can help you launch a TCP server and rebind its port so that incoming Websockets-based communication is parsed and forwarded to the server on the proper (rebinded) port. My question is, can this mechanism be used to wrap a server that forks its children which in turn communicate with the client on a different port. Specifically, I am interested in websockifying a Postgres server, which typically listens on port 5432 and for a new incoming connection it forks a child which serves all future request from that client. (If it helps, Oracle RDBMS and many other servers, RDBMS or not, also use similar method.) [1] https://github.com/kanaka/websockify

  Read the article

• Socket programming C# vs C++

  - by klay

  Hi My company is willing to develop a server application, the application will use one port, clients will connect to this port and sending data every 3 minutes, casually the server will send some data. my questions are: how many connection can be handled when connecting to one port? which language Do we choose to write the Application (mainly between C# and C++)? (performance, ease of development) thanks

  Read the article

< Previous Page | 207 208 209 210 211 212 213 214 215 216 217 218  | Next Page >