Search Results

Search found 83224 results on 3329 pages for 'web application firewall'.

Page 211/3329 | < Previous Page | 207 208 209 210 211 212 213 214 215 216 217 218  | Next Page >

• Iptables rule creation error: No chain/target/match by that name

  - by MikO

  I'm trying to create my first VPN on a VPS with CentOS 6, following this tutorial. When I have to create an iptables rule to allow proper routing of VPN subnet, with this command: iptables -t nat -A POSTROUTING -s 10.8.0.0/24 -o eth0 -j MASQUERADE It throws this error: iptables: No chain/target/match by that name I was searching and I've found that this error is usually thrown when you misspell something, but as far as I understand, the rule is correct...

  Read the article

• How can I block all traffic except web traffic?

  - by toddoon

  I have wrote my rules like this: iptables -P INPUT DROP iptables -P OUTPUT DROP iptables -P FORWARD DROP iptables -A OUTPUT -i eth0 -p tcp --dport 80 -j ACCEPT What do I do next?

  Read the article

• Redirection of outbound UDP port NTP.

  - by pboin

  For my residential service, I changed ISPs to Zoom/Armstrong. Just after that, my NTP daemons stopped working. I dug deep and diagnosed the problem: Unprivileged ports are getting out. When i run 'ntpdate' for example, I go out on a high, unprivleged port, and get a response on UDP 123. That's fine. The 'ntpd' daemon though, expects to go out on 123 and get its reply there as well. This must be a common problem, because it's directly addressed in the NTP troubleshooting guide. Just to see what would happen, I wrote a detailed email to the general support address at Armstrong. They replied almost immediately with a complete technical answer! They have everything <1024 blocked, except for a few ports to support outbound VPN. So, the question: Can I use IPtables to essentially re-write my outbound UDP 123 up to 2123 or something like that? If I do, does there need to be a corresponding 2123-123 rule to translate the reply? This seems like NAT, but with ports, not addresses. True, I could run ntpdate from cron, but that loses all of the adjustment smarts of NTP.

  Read the article

• iptables and snatting to different networks

  - by codingfreak

  linuxbox (p.q.r.t) | | INTERNAL ------ ABCD ----- INTERNET (p.q.r.s) (m.n.o.k) ABCD has 3 interfaces connected to linuxbox, INTERNAL N/W, INTERNET. Linuxbox has a private address (p.q.r.t). At present I am snatting the packets from linuxbox to INTERNET at ABCD. I have a small doubt regarding the FTP from linuxbox since I have to support ftp from linuxbox to both INTERNAL N/W as well as in INTERNET. How can I right a rule in iptables present in ABCD where it can decide if the destination ip-address of ftp server is within INTERNAL N/W or in INTERNET and do natting accordingly.

  Read the article

• Windows Server 2008: Limit UDP/TCP packets per IP or ban

  - by WBAR

  How I can limit UDP/TCP packets per IP send to my host (or better PORT) per second or minute ? Would be nice to ban that IP for 12/24 hours or even for ever. I got Windows Server 2008 and I'm very poor in Windows administration but quite good in Linux. EDIT: By basic problem is that They sending a lot of rubbish UPD and TCP packets.. TCP packets without SYNCH, fragmented UDP packets so my servers stop responding.. So I need to cut off users (IPs) sending more than X packets per second. I need solution witch provides me, somehow, configurable: X packets of certain type (UDP, TCP or both - lets say parameter named Z ) are allowed to be received by IP on Y port, otherwise this packet should be DROPPED. My virtual hosts are hosted by VirtualBox and I'm able to forward all incoming packets certain type and certain port to the specific Virtual Host, but I need to DROP them before my VirtualBox receive them.

  Read the article

• File replication among EC2 instances

  - by Peuge

  I am pretty new to AWS so please excuse my ignorance. We are wanting to have a setup whereby we have a SQL DB instance + web server instance. However we would like the Web server to sit behind an ELB thus allowing us to use Autoscaling. My question however is how to we replicate the web app across instances? Say for example we have two web servers running and we need to make a critical update to the web app, ultimately we would only want to upload to one instance and not both. Is it even best practice to store your web app on the instance or are there better ways to store and share the app between instances?

  Read the article

• error: "net.netfilter.nf_conntrack_acct" is an unknown key

  - by anonymous

  Hello, i have the next error when i run 'sysctl -p' error: "net.netfilter.nf_conntrack_acct" is an unknown key net.netfilter.nf_conntrack_acct = 1 net.ipv4.netfilter.ip_conntrack_max = 9527600 net.ipv4.netfilter.ip_conntrack_tcp_timeout_established = 7200 lsmod ipv6 289352 34 loop 19724 0 nf_conntrack_ipv4 19352 0 nf_conntrack 71440 1 nf_conntrack_ipv4 joydev 15232 0 evdev 14592 0 ext3 125456 3 jbd 54696 1 ext3 mbcache 13188 1 ext3 raid1 24832 4 md_mod 81700 5 raid1 thermal_sys 17728 0 Debian 5.0.8 Any idea? Thanks

  Read the article

• How can I make my livebox route to my external IP address for a computer in the DMZ?

  - by Noli

  I have a sagem livebox 2 (Fiber optic model), and have placed my computer in a DMZ. People from outside of my network can access my comp fine via its external dyndns.org address, yet when I try to call the public dyndns.org address from inside my network, I get redirected to the internal admin site on the router. How can I make it so that I can see my comp from the public address like everyone else? What kinds of questions should I be asking or looking into? Thanks

  Read the article

• Changing Internet connection on ISA Server 2000

  - by garyb32234234

  Hi We are getting a new internet connection installed and will need to unplug the old one and connect this to our ISA Server 2000. Will this be a simple swap out job? We will be given a new ip, which i know i will have to enter into the external network card TCP/IP page. I will also be given the default gateway to enter. The ISP engineer said we may have to reset the ARP? cache, if we dont know how we will have to reset the ISA server? Has anyone any experience? The current connection is with the same ISP but it was owned by the business park were we are located and they linked up an ethernet port to what i assume is their own router. Hope you can help, i know that ISA 2000 is somewhat less easy to use than the newer versions.

  Read the article

• Auto Forward mails to gmail from Outlook

  - by Jaison

  I have a highly secured computer windows server 2003 where my outlook express is configured, i want to forward all the mails coming from Outlook to gmail. I put some auto forward rule in outlook but its not working. (May be auto forwarding is disabled). I can forward mails manually. Is there anyway to get rid off this problem?

  Read the article

• iptables -- OK, **now** am I doing it right?

  - by Agvorth

  This is a follow up to a previous question where I asked whether my iptables config is correct. CentOS 5.3 system. Intended result: block everything except ping, ssh, Apache, and SSL. Based on xenoterracide's advice and the other responses to the question (thanks guys), I created this script: # Establish a clean slate iptables -P INPUT ACCEPT iptables -P FORWARD ACCEPT iptables -P OUTPUT ACCEPT iptables -F # Flush all rules iptables -X # Delete all chains # Disable routing. Drop packets if they reach the end of the chain. iptables -P FORWARD DROP # Drop all packets with a bad state iptables -A INPUT -m state --state INVALID -j DROP # Accept any packets that have something to do with ones we've sent on outbound iptables -A INPUT -m state --state RELATED,ESTABLISHED -j ACCEPT # Accept any packets coming or going on localhost (this can be very important) iptables -A INPUT -i lo -j ACCEPT # Accept ICMP iptables -A INPUT -p icmp -j ACCEPT # Allow ssh iptables -A INPUT -p tcp --dport 22 -j ACCEPT # Allow httpd iptables -A INPUT -p tcp --dport 80 -j ACCEPT # Allow SSL iptables -A INPUT -p tcp --dport 443 -j ACCEPT # Block all other traffic iptables -A INPUT -j DROP Now when I list the rules I get... # iptables -L -v Chain INPUT (policy ACCEPT 0 packets, 0 bytes) pkts bytes target prot opt in out source destination 0 0 DROP all -- any any anywhere anywhere state INVALID 9 612 ACCEPT all -- any any anywhere anywhere state RELATED,ESTABLISHED 0 0 ACCEPT all -- lo any anywhere anywhere 0 0 ACCEPT icmp -- any any anywhere anywhere 0 0 ACCEPT tcp -- any any anywhere anywhere tcp dpt:ssh 0 0 ACCEPT tcp -- any any anywhere anywhere tcp dpt:http 0 0 ACCEPT tcp -- any any anywhere anywhere tcp dpt:https 0 0 DROP all -- any any anywhere anywhere Chain FORWARD (policy DROP 0 packets, 0 bytes) pkts bytes target prot opt in out source destination Chain OUTPUT (policy ACCEPT 5 packets, 644 bytes) pkts bytes target prot opt in out source destination I ran it and I can still log in, so that's good. Anyone notice anything major out of wack?

  Read the article

• Shorewall SHOW DYNAMIC command doesn't work

  - by Andrew Burns

  Setting up shorewall dynamic zones, http://shorewall.net/Dynamic.html shows the command shorewall show dynamic zone where zone is one of your zones. I can get the add and delete commands to work, but not the show dynamic command. Here is a shell session, with output from ipset list that proves that the items are indeed there. $ ipset list CPREM_br0 Name: CPREM_br0 Type: hash:ip Header: family inet hashsize 1024 maxelem 65536 Size in memory: 16520 References: 66 Members: 192.168.85.153 $ shorewall add br0:192.168.85.200 CPREM Host br0:192.168.85.200 added to zone CPREM $ shorewall show dynamic CPREM $ ipset list CPREM_br0 Name: CPREM_br0 Type: hash:ip Header: family inet hashsize 1024 maxelem 65536 Size in memory: 16536 References: 66 Members: 192.168.85.153 192.168.85.200 $ shorewall delete br0:192.168.85.200 CPREM Host br0:192.168.85.200 deleted from zone CPREM $ ipset list CPREM_br0 Name: CPREM_br0 Type: hash:ip Header: family inet hashsize 1024 maxelem 65536 Size in memory: 16536 References: 66 Members: 192.168.85.153 I am using the packaged version from Ubuntu 12.04 (4.4.26.1-1)

  Read the article

• ASA 5505 8.4 open ports for subnet

  - by fwrawx

  I have an ASA 5505 running 8.4 with its outside interface plugged into our internal network. I want to open up access to hosts on one of the vlans behind that ASA to hosts on our internal network. I was just starting to grasp NAT on our older PIX but the ASA 8.4 has me confused now. Given a clean ASA with an outside vlan of 10.0.0.1/24 and test vlan of 10.0.1.1/24 what's the basic configuration needed to allow any hosts on the outside network to have access to any of the hosts on the test network?

  Read the article

• Installing MFC (vs2005) application on Windows 2008 R2 64

  - by olich

  I've build an application that runs on Windows 2003, it is an old style MFC application. Today I need to install the application on a Windows 2008 R2 64 system. I have failures during installation and the application does not run. The application is build with VisualStudio2005, and uses COM objects. The MSI register the objects but it fails with the error code : HRESULT -2147010895. Any idea why the COM registration failed? I've tried to install the "Microsoft Visual C++ 2005 Redistributable Package (x86)" but it doesn't help. I've tried to register the COM objects with the regsvr32 after the installation but sadly it doesn't help. I've tries to install the application on Windows 2008 R2 32, and it works perfectly. I am quite new with 64 systems, so any help will be appreciated. tia olich

  Read the article

• Srvany Starts but Application doesn't

  - by mharran

  I used Instsrv and Srvany as to create a service on W2008; the Srvany service starts okay but the application does not start. The application is TeamSpeak 3 btw. I don't think it's an issue with my W2008 setup as I have a previous version of the application set up the exact same way and running perfectly. Also, I have no problem manually starting the application even when I copy and paste into the 'Run' box the path used for the application by Srvany. I looked at Events but nothing there except notification that the service has entered the running state, didn't really expect any errors as the service has started even though the application hasn't. Any suggestions on what could be the problem?

  Read the article

• Bridge Intrusion Prevention Vyatta

  - by Steve

  I am trying to create a bridge with ThreatStop, IPS and block a few ports. This bridge will sit in front of my servers. All is working apart from the IPS. I have read the documentation on configuring IPS, I have something configured that it hasn't complained about and nothing is logged so I believe that it isn't working. Is it possible to set-up IPS on a vyatta bridge? Also is it possible to read the logs/events with Snorby? I have also posted this on the Vyatta forums

  Read the article

• Restrict Computer or Users from Internet but allow access to intranet and Windows Update / ePO?

  - by MoSiAc

  So this may be impossible but I've been asked to try and find something about it. So far nothing I have found is possible. I need to restrict specific machines or user accounts from regular Internet access but let them have access to the intranet portion of our network. I do not have Active Directory control, nor does anyone at my local workplace (corporate control in a different state). I have tried going through IPsec and doing this per local machine, but that system seems to have been removed from the images that are installed on these machines so that is out. So far the only other option I can think of is assigning the machines a specific ip address and removing their gateway access. This would probably work but the machines need to be able to receive updates that are being pushed to them through ePO and LanDesk. I would really like to do this on the user level because then if I need to do tech work to the machine and need internet access I can get to it but a "special" user could login and not be able to get into anything.

  Read the article

• ASA5500 series logging for management interface in transparent mode

  - by ANervousTwitch

  i have a cisco asa5520 in transparent mode. the interface is on the same subnet as some windows machines, which are generating a lot of broadcast traffic that is filling up the logs. is there any way to have it not log that its blocking those packets? its a bunch of these messages: "through-the-device packet to from management-only network is denied: udp src..." im also seeing some of those zeroconf requests that id like to drop logging for. i tried to just put a rule on the management interface, but apparently thats not allowed.

  Read the article

• Limiting and redirect port access with useragent

  - by linuxcore

  I'm trying to write iptables string match rule To block http://domain.com:8888 and https://domain.com:8888 when it matches the supplied string in the rule. And another rule to redirect the ports also from 8888 to 7777 I tried following rules but unfortunately didn't work iptables -A INPUT -p tcp -s 0.0.0.0/0 -m string --string linuxcore --algo bm --sport 8888 -j DROP iptables -t raw -A PREROUTING -m string --algo bm --string linuxcore -p tcp -i eth0 --dport 8888 -j DROP iptables -t nat -A PREROUTING -p tcp --dport 8888 -m string --algo bm --string "linuxcore" -j REDIRECT --to-port 7777 iptables -A INPUT -t nat -p tcp --dport 8888 -m string --algo bm --string "linuxcore" -j DROP I want to do this from iptables not the webserver because the server may not have a webserver and those ports are working on internal proxy or something like ..etc

  Read the article

• Allow access to printer between interfaces on Cisco ASA5510

  - by Jonas Stensved

  I have a Cisco ASA5510 where we have to separate networks on two separate interfaces. The networks have and should have nothing to do with each other except that network B needs to access a printer on network A. Network A: 192.168.137.0/24 Printer: 192.168.137.20 Network B: 192.168.0.0/24 I've added an incoming rule from Network A to the Printer IP in the ASDM interface but clients can't print. Our previous router was configured to let traffic through so the clients on Network B is already configured so it think it should work if the traffic is allowed. How do I let clients on Network B communicate with the printer?

  Read the article

• What web browsers support non-latin characters 'out of the box'?

  - by rutherford

  With ICANN approving the first full Internationalised Domain Names for non-latin scripts such as Arabic, Cyrillic, Chinese, etc do all browsers support these character sets out of the box?

  Read the article

• SNMP closed state in CentOS

  - by anksoWX

  I'm having a problem here, I've added to my IPtables rules this: -A INPUT -p tcp -m state --state NEW -m tcp --dport 161 -j ACCEPT -A INPUT -p udp -m state --state NEW -m udp --dport 161 -j ACCEPT but when I scan with nmap or any other tool it says this: Not shown: 998 filtered ports PORT STATE SERVICE 22/tcp open ssh 161/tcp closed snmp also when I am doing: netstat -apn | grep snmpd tcp 0 0 127.0.0.1:199 0.0.0.0:* LISTEN 3669/snmpd<br> udp 0 0 0.0.0.0:161 0.0.0.0:* 3669/snmpd<br> unix 2 [ ] DGRAM 226186 3669/snmpd Also: service iptables status Table: filter Chain INPUT (policy ACCEPT) num target prot opt source destination 1 ACCEPT all -- 0.0.0.0/0 0.0.0.0/0 state RELATED,ESTABLISHED 2 ACCEPT icmp -- 0.0.0.0/0 0.0.0.0/0 3 ACCEPT all -- 0.0.0.0/0 0.0.0.0/0 4 ACCEPT tcp -- 0.0.0.0/0 0.0.0.0/0 state NEW tcp dpt:161 5 ACCEPT udp -- 0.0.0.0/0 0.0.0.0/0 state NEW udp dpt:161 6 ACCEPT tcp -- 0.0.0.0/0 0.0.0.0/0 state NEW tcp dpt:22 7 REJECT all -- 0.0.0.0/0 0.0.0.0/0 reject-with icmp-host-prohibited Chain FORWARD (policy ACCEPT) num target prot opt source destination 1 REJECT all -- 0.0.0.0/0 0.0.0.0/0 reject-with icmp-host-prohibited Chain OUTPUT (policy ACCEPT) num target prot opt source destination Any idea what's going on? There is no UDP in closed/open state. what do I have to do?

  Read the article

• How did Google get on my Mac?

  - by SamGoody

  Am running a MacBook Pro, and have never installed Chrome, Google Earth, or anything blatantly Google. Just installed Little Snitch (are there no good free firewalls for Mac?) and see that CURL is sending to Google every few minutes, as is a request to Google update and more. Little Snitch doesn't say what program setup these requests. So, how do I find out how G got on my machine, why is it sending so many requests (every minute or so) and how do I remove it (and is it there for reasons other than to help G spy on me)?

  Read the article

• Redirection of outbound UDP port.

  - by pboin

  For my residential service, I changed ISPs to Zoom/Armstrong. Just after that, my NTP daemons stopped working. I dug deep and diagnosed the problem: Unprivileged ports are getting out. When i run 'ntpdate' for example, I go out on a high, unprivleged port, and get a response on UDP 123. That's fine. The 'ntpd' daemon though, expects to go out on 123 and get its reply there as well. This must be a common problem, because it's directly addressed in the NTP troubleshooting guide. Just to see what would happen, I wrote a detailed email to the general support address at Armstrong. They replied almost immediately with a complete technical answer! They have everything <1024 blocked, except for a few ports to support outbound VPN. So, the question: Can I use IPtables to essentially re-write my outbound UDP 123 up to 2123 or something like that? If I do, does there need to be a corresponding 2123-123 rule to translate the reply? This seems like NAT, but with ports, not addresses. I tried, but can't seem to get iptables to do what I want. I'm not sure if it's my lack of skill, or if I'm trying the wrong solution. True, I could run ntpdate from cron, but that loses all of the adjustment smarts of NTP.

  Read the article

• unable to start apache after changes to rc.conf and resov.conf

  - by shupru

  I had a working configuration this morning with the following simple /etc/rc.conf ifconfig_rl0="DHCP" ifconfig_xl="inet 192.168.1.11 netmask 255.255.255." defaultrouter="192.168.1.1" I added the following lines: firewall_enable="YES" firewall_type="SIMPLE" firewall_logging="YES" sshd_enable="YES" apache_enable="YES" mysql_enable="YES" my httpd.conf includes: NameVirtualHost 192.168.1.11 <VirtualHost 192.168.1.11> ... </VirtualHost> now apache and ssh server are down. changed rc.conf back to last working configuration and still no ssh or apache apachectl start #--> /usr/local/sbin/apachectl start: httpd could not be started apachectl status #--> Looking up localhost Making http connection to localhost Alert!: Unable to connect to remote host.

  Read the article

< Previous Page | 207 208 209 210 211 212 213 214 215 216 217 218  | Next Page >