Search Results

Search found 15160 results on 607 pages for 'boot disk'.

facebook twitter digg google delicious technorati stumbleupon myspace wordpress linkedin gmail igoogle windows live tumblr viadeo yahoo buzz yahoo mail yahoo bookmarks favorites email print

Page 212/607 | < Previous Page | 208 209 210 211 212 213 214 215 216 217 218 219  | Next Page >

  • How can I get rid of the motd message "*** /dev/sdb1 will be checked for errors at next reboot ***"? [duplicate]

    - by kmm
    This question already has an answer here: Persistent “disk will be checked…” in the message of the day (motd) even after reboot 3 answers My motd persistently has: *** /dev/sdb1 will be checked for errors at next reboot *** The problem is that I don't have /dev/sdb1 on my system. I only have /dev/sdb2 (mouted as /) and /dev/sda1 which mounts to /media/backup. I delete that line from /etc/motd, but it reappears after reboot. Here's my df output: Filesystem Size Used Avail Use% Mounted on /dev/sdb2 73G 3.7G 66G 6% / udev 490M 4.0K 490M 1% /dev tmpfs 200M 760K 199M 1% /run none 5.0M 0 5.0M 0% /run/lock none 498M 0 498M 0% /run/shm /dev/sda1 1.9T 429G 1.4T 25% /media/backup Update Here is the output of sudo fdisk -l Disk /dev/sda: 2000.4 GB, 2000398934016 bytes 255 heads, 63 sectors/track, 243201 cylinders, total 3907029168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x0003dfc2 Device Boot Start End Blocks Id System /dev/sda1 63 3907024064 1953512001 83 Linux Disk /dev/sdb: 80.0 GB, 80026361856 bytes 255 heads, 63 sectors/track, 9729 cylinders, total 156301488 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00049068 Device Boot Start End Blocks Id System /dev/sdb1 152301568 156301311 1999872 82 Linux swap / Solaris /dev/sdb2 * 2048 152301567 76149760 83 Linux Partition table entries are not in disk order I guess /dev/sdb1 is my swap space.

    Read the article

  • How do i change the BIOS boot splash screen?

    - by YumYumYum
    I have a Dell PC which has very ugly and bad luck looking Alien face on every boot. I want to change it or disable it forever, but in Bios they do not have any options. How can i change this from my linux Fedora or ArchLinux which is running now? Tried following does not work. ( http://www.pixelbeat.org/docs/bios/ ) ./flashrom -r firmware.old #save current flash ROM just in case ./flashrom -wv firmware.new #write and verify new flash ROM image Also tried: $ cat c.c #include <stdio.h> #include <inttypes.h> #include <netinet/in.h> #include <stdlib.h> #include <string.h> #include <sys/types.h> #include <sys/stat.h> #include <fcntl.h> #include <unistd.h> #define lengthof(x) (sizeof(x)/sizeof(x[0])) uint16_t checksum(const uint8_t* data, int len) { uint16_t sum = 0; int i; for (i=0; i<len; i++) sum+=*(data+i); return htons(sum); } void usage(void) { fprintf(stderr,"Usage: therm_limit [0,50,53,56,60,63,66,70]\n"); fprintf(stderr,"Report therm limit of terminal in BIOS\n"); fprintf(stderr,"If temp specifed, it is changed if required.\n"); exit(EXIT_FAILURE); } #define CHKSUM_START 51 #define CHKSUM_END 109 #define THERM_OFFSET 67 #define THERM_SHIFT 0 #define THERM_MASK (0x7 << THERM_SHIFT) #define THERM_OFF 0 uint8_t thermal_limits[]={0,50,53,56,60,63,66,70}; #define THERM_MAX (lengthof(thermal_limits)-1) #define DEV_NVRAM "/dev/nvram" #define NVRAM_MAX 114 uint8_t nvram[NVRAM_MAX]; int main(int argc, char* argv[]) { int therm_request = -1; if (argc>2) usage(); if (argc==2) { if (*argv[1]=='-') usage(); therm_request=atoi(argv[1]); int i; for (i=0; i<lengthof(thermal_limits); i++) if (thermal_limits[i]==therm_request) break; if (i==lengthof(thermal_limits)) usage(); else therm_request=i; } int fd_nvram=open(DEV_NVRAM, O_RDWR); if (fd_nvram < 0) { fprintf(stderr,"Error opening %s [%m]\n", DEV_NVRAM); exit(EXIT_FAILURE); } if (read(fd_nvram, nvram, sizeof(nvram))==-1) { fprintf(stderr,"Error reading %s [%m]\n", DEV_NVRAM); close(fd_nvram); exit(EXIT_FAILURE); } uint16_t chksum = *(uint16_t*)(nvram+CHKSUM_END); printf("%04X\n",chksum); exit(0); if (chksum == checksum(nvram+CHKSUM_START, CHKSUM_END-CHKSUM_START)) { uint8_t therm_byte = *(uint16_t*)(nvram+THERM_OFFSET); uint8_t therm_status=(therm_byte & THERM_MASK) >> THERM_SHIFT; printf("Current thermal limit: %d°C\n", thermal_limits[therm_status]); if ( (therm_status == therm_request) ) therm_request=-1; if (therm_request != -1) { if (therm_status != therm_request) printf("Setting thermal limit to %d°C\n", thermal_limits[therm_request]); uint8_t new_therm_byte = (therm_byte & ~THERM_MASK) | (therm_request << THERM_SHIFT); *(uint8_t*)(nvram+THERM_OFFSET) = new_therm_byte; *(uint16_t*)(nvram+CHKSUM_END) = checksum(nvram+CHKSUM_START, CHKSUM_END-CHKSUM_START); (void) lseek(fd_nvram,0,SEEK_SET); if (write(fd_nvram, nvram, sizeof(nvram))!=sizeof(nvram)) { fprintf(stderr,"Error writing %s [%m]\n", DEV_NVRAM); close(fd_nvram); exit(EXIT_FAILURE); } } } else { fprintf(stderr,"checksum failed. Aborting\n"); close(fd_nvram); exit(EXIT_FAILURE); } return EXIT_SUCCESS; } $ gcc c.c -o bios # ./bios 16DB

    Read the article

  • Sony VAIO is booting directly into Windows without showing grub

    - by Rohan Dhruva
    I bought a new Sony Vaio S series laptop. It uses Insyde H2O BIOS EFI, and trying to install Linux on it is driving me crazy. root@kubuntu:~# parted /dev/sda print Model: ATA Hitachi HTS72756 (scsi) Disk /dev/sda: 640GB Sector size (logical/physical): 512B/4096B Partition Table: gpt Number Start End Size File system Name Flags 1 1049kB 274MB 273MB fat32 EFI system partition hidden 2 274MB 20.8GB 20.6GB ntfs Basic data partition hidden, diag 3 20.8GB 21.1GB 273MB fat32 EFI system partition boot 4 21.1GB 21.3GB 134MB Microsoft reserved partition msftres 5 21.3GB 342GB 320GB ntfs Basic data partition 6 342GB 358GB 16.1GB ext4 Basic data partition 7 358GB 374GB 16.1GB ntfs Basic data partition 8 374GB 640GB 266GB ntfs Basic data partition What is surprising is that there are 2 EFI system partitions on the disk. The sda2 partition is a 20gb recovery partition which loads windows with a basic recovery interface. This is accessible by pressing the "ASSIST" button as opposed to the normal power button. I presume that the sda1 EFI System Partition (ESP) loads into this recovery. The sda3 ESP has more fleshed out entries for Microsoft Windows, which actually goes into Windows 7 (as confirmed by bcdedit.exe on Windows). Ubuntu is installed on sda6, and while installation I chose sda3 as my boot partition. The installer correctly created a sda3/EFI/ubuntu/grubx64.efi application. The real problem: for the life of me, I can't set it to be the default! I tried creating a sda3/startup.nsh which called grubx64.efi, but it didn't help -- on rebooting, the system still boots into windows. I tried using efibootmgr, and that shows as it it worked: root@kubuntu:~# efibootmgr BootCurrent: 0000 BootOrder: 0000,0001 Boot0000* EFI USB Device Boot0001* Windows Boot Manager root@kubuntu:~# efibootmgr --create --gpt --disk /dev/sda --part 3 --write-signature --label "GRUB2" --loader "\\EFI\\ubuntu\\grubx64.efi" BootCurrent: 0000 BootOrder: 0002,0000,0001 Boot0000* EFI USB Device Boot0001* Windows Boot Manager Boot0002* GRUB2 root@kubuntu:~# efibootmgr BootCurrent: 0000 BootOrder: 0002,0000,0001 Boot0000* EFI USB Device Boot0001* Windows Boot Manager Boot0002* GRUB2 However, on rebooting, as you guessed, the machine rebooted directly back into Windows. The only things I can think of are: The sda1 partition is somehow being used Overwrite /EFI/Boot/bootx64.efi and /EFI/Microsoft/Boot/bootmgfw.efi with grubx64.efi [but this seems really radical]. Can anyone please help me out? Thanks -- any help is greatly appreciated, as this issue is driving me crazy!

    Read the article

  • external USB HD doesn't show up on 'sudo fdisk -l' on one Ubuntu, shows up on another (both 'precise')

    - by Menelaos
    I have a 1.5TB WD external USB HDD and two Ubuntu systems, both 'precise'. When I plug the disk on system A it doesn't show up on the output of sudo fdisk -l nor is it automatically mounted (note that that wasn't always the case - it used to appear in the past). When I plug it on system B (again Ubuntu precise) it shows up when I do a sudo fdisk -l (output appended at the end) and mounts automatically just fine. What does this discrepancy point to and what kind of diagnostics should I run / tools I should use to troubleshoot the problem? I followed the suggestion I received to do a sudo tail -f /var/log/syslog and the output is the following when I plug, unplug and replug the USB cable on System A: Sep 14 23:27:09 thorin mtp-probe: checking bus 2, device 3: "/sys/devices/pci0000:00/0000:00:13.2/usb2/2-2" Sep 14 23:27:09 thorin mtp-probe: bus: 2, device: 3 was not an MTP device Sep 14 23:28:01 thorin kernel: [ 338.994295] usb 2-2: USB disconnect, device number 3 Sep 14 23:28:04 thorin kernel: [ 341.808139] usb 2-2: new high-speed USB device number 4 using ehci_hcd Sep 14 23:28:04 thorin mtp-probe: checking bus 2, device 4: "/sys/devices/pci0000:00/0000:00:13.2/usb2/2-2" Sep 14 23:28:04 thorin mtp-probe: bus: 2, device: 4 was not an MTP device Sep 14 23:29:54 thorin AptDaemon: INFO: Quitting due to inactivity Sep 14 23:29:54 thorin AptDaemon: INFO: Quitting was requested (I guess the last two message are irrelevant). Output of sudo fdisk -l on System B $ sudo fdisk -l Disk /dev/sda: 1500.3 GB, 1500301910016 bytes 255 heads, 63 sectors/track, 182401 cylinders, total 2930277168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00070db4 Device Boot Start End Blocks Id System /dev/sda1 * 2048 2905114623 1452556288 83 Linux /dev/sda2 2905116670 2930276351 12579841 5 Extended /dev/sda5 2905116672 2930276351 12579840 82 Linux swap / Solaris Disk /dev/sdb: 250.1 GB, 250059350016 bytes 255 heads, 63 sectors/track, 30401 cylinders, total 488397168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x9c849c84 Device Boot Start End Blocks Id System /dev/sdb1 * 63 488375999 244187968+ 7 HPFS/NTFS/exFAT Disk /dev/sdg: 1500.3 GB, 1500299395072 bytes 255 heads, 63 sectors/track, 182401 cylinders, total 2930272256 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x0003e17f Device Boot Start End Blocks Id System /dev/sdg1 2048 2930272255 1465135104 7 HPFS/NTFS/exFAT

    Read the article

  • High CPU load for 1:30 minutes when mounting ext4-raid partition

    - by sirion
    I have a raid 5 (software) with 5x2TB drives. I encrypted the raid with cryptsetup and put an ext4-partition on top. In the beginning opening and mounting the raid took less than 10 seconds, now (for a few weeks) mounting alone takes 1:30 minutes and the cpu stays around 93% the whole time: The output of "time sudo mount /dev/mapper/8000 /media/8000" is: real 1m31.952s user 0m0.008s sys 1m25.229s At the same time only one line is added to /var/log/syslog: kernel: [ 2240.921381] EXT4-fs (dm-1): mounted filesystem with ordered data mode. Opts: (null) My Ubuntu-version is "12.04.1 LTS" and no updates are pending. I checked the partition with fsck, but it says that all is ok. The "cryptsetup luksOpen" command only takes a few seconds. I also tried changing the raid-bitmap (as it was suggested in some forum) but it did not change the behaviour. sudo mdadm --grow /dev/md0 -b internal and sudo mdadm --grow /dev/md0 -b none I had the idea that it might be the hardware being slow, but a read test with "sudo hdparm -t /dev/md0" spit out values between 62 and 159 MB/sec: Timing buffered disk reads: 382 MB in 3.00 seconds = 127.14 MB/sec Timing buffered disk reads: 482 MB in 3.02 seconds = 159.62 MB/sec Timing buffered disk reads: 190 MB in 3.03 seconds = 62.65 MB/sec Timing buffered disk reads: 474 MB in 3.02 seconds = 157.12 MB/sec Although I think it is strange that the read rate jumps by more than 100% - could that mean something? The speed test when reading from the mapped (decrypted) device shows similar behavior, although it is of course much slower. "sudo hdparm -t /dev/mapper/8000": Timing buffered disk reads: 56 MB in 3.02 seconds = 18.54 MB/sec Timing buffered disk reads: 122 MB in 3.09 seconds = 39.43 MB/sec Timing buffered disk reads: 134 MB in 3.02 seconds = 44.35 MB/sec The output of a verbose mount "mount -vvv /dev/mapper/8000 /media/8000" does not help much: mount: fstab path: "/etc/fstab" mount: mtab path: "/etc/mtab" mount: lock path: "/etc/mtab~" mount: temp path: "/etc/mtab.tmp" mount: UID: 0 mount: eUID: 0 mount: spec: "/dev/mapper/8000" mount: node: "/media/8000" mount: types: "(null)" mount: opts: "(null)" mount: you didn't specify a filesystem type for /dev/mapper/8000 I will try type ext4 mount: mount(2) syscall: source: "/dev/mapper/8000", target: "/media/8000", filesystemtype: "ext4", mountflags: -1058209792, data: (null) Any idea where I could find additional information on why mounting takes so long, or what additional tests I could run?

    Read the article

  • Why doesn't Ubuntu detect my second hard drive?

    - by user93179
    I am new to Linux and to Ubuntu, I was wondering, I have two hard drives setup in SATA ports (non-raid, at least I don't think they are). I installed ubuntu unto the drives fresh without any previous versions or windows at all. However when I got the Ubuntu 12.04 LTS working, all I see is 1 x 120 gigabyte harddrive. Also, not sure if this is important or not, my hard drives are SSD. My computer specs are Asus P9Z77-V-LK Nvidia Geforce GTX 660 TI Intel i5 3570k 3.4 /proc/partitions shows: major minor #blocks name 8 0 117220824 sda 8 1 117219328 sda1 8 16 117220824 sdb 8 17 96256 sdb1 8 18 108780544 sdb2 8 19 8342528 sdb3 11 0 1048575 sr0 and ls -l /sys/block/ | grep -v /virtual/: lrwxrwxrwx 1 root root 0 Sep 27 17:26 sda - ../devices/pci0000:00/0000:00:1f.2/host0/target0:0:0/0:0:0:0/block/sda lrwxrwxrwx 1 root root 0 Sep 27 17:26 sdb - ../devices/pci0000:00/0000:00:1f.2/host1/target1:0:0/1:0:0:0/block/sdb lrwxrwxrwx 1 root root 0 Sep 27 22:26 sdc - ../devices/pci0000:00/0000:00:1a.0/usb1/1-1/1-1.1/1-1.1:1.0/host6/target6:0:0/6:0:0:0/block/sdc lrwxrwxrwx 1 root root 0 Sep 27 22:04 sr0 - ../devices/pci0000:00/0000:00:1f.2/host3/target3:0:0/3:0:0:0/block/sr0 sudo file -s /dev/sd*: /dev/sda: x86 boot sector; partition 1: ID=0x7, starthead 32, startsector 2048, 234438656 sectors, code offset 0xc0, OEM-ID " ?", Bytes/sector 190, sectors/cluster 124, reserved sectors 191, FATs 6, root entries 185, sectors 64514 (volumes 32 MB) , physical drive 0x7e, dos 32 MB) , FAT (32 bit), sectors/FAT 749, reserved3 0x800000, serial number 0x35361a2b, unlabeled /dev/sdb2: Linux rev 1.0 ext4 filesystem data, UUID=387761ac-5eba-4d0f-93ba-746a82fb541d (needs journal recovery) (extents) (large files) (huge files) /dev/sdb3: data /dev/sdc: x86 boot sector; partition 1: ID=0xc, active, starthead 0, startsector 8064, 30473088 sectors, code offset 0xc0 /dev/sdc1: x86 boot sector, code offset 0x58, OEM-ID "SYSLINUX", sectors/cluster 64, reserved sectors 944, Media descriptor 0xf8, heads 128, hidden sectors 8064, sectors 30473088 (volumes 32 MB) , FAT (32 bit), sectors/FAT 3720, Backup boot sector 8, serial number 0xf90c12e9, label: "KINGSTON " /dev/sda1: x86 boot sector, code offset 0x52, OEM-ID "NTFS ", sectors/cluster 8, reserved sectors 0, Media descriptor 0xf8, heads 255, hidden sectors 2048, dos 32 MB) , FAT (32 bit), sectors/FAT 749, reserved3 0x800000, serial number 0x35361a2b, unlabeled Any help would be greatly appreciated! Thanks Another thing I noticed is, when i use gparted to locate my drives, it seems that sda1 is my second drive that I am not detecting when I boot up and my ubuntu + FAT Boot files are installed in sdb1

    Read the article

  • e2fsck extremely slow, although enough memory exists

    - by kaefert
    I've got this external USB-Disk: kaefert@blechmobil:~$ lsusb -s 2:3 Bus 002 Device 003: ID 0bc2:3320 Seagate RSS LLC As can be seen in this dmesg output, there is some problem that prevents that disk from beeing mounted: kaefert@blechmobil:~$ dmesg ... [ 113.084079] usb 2-1: new high-speed USB device number 3 using ehci_hcd [ 113.217783] usb 2-1: New USB device found, idVendor=0bc2, idProduct=3320 [ 113.217787] usb 2-1: New USB device strings: Mfr=2, Product=3, SerialNumber=1 [ 113.217790] usb 2-1: Product: Expansion Desk [ 113.217792] usb 2-1: Manufacturer: Seagate [ 113.217794] usb 2-1: SerialNumber: NA4J4N6K [ 113.435404] usbcore: registered new interface driver uas [ 113.455315] Initializing USB Mass Storage driver... [ 113.468051] scsi5 : usb-storage 2-1:1.0 [ 113.468180] usbcore: registered new interface driver usb-storage [ 113.468182] USB Mass Storage support registered. [ 114.473105] scsi 5:0:0:0: Direct-Access Seagate Expansion Desk 070B PQ: 0 ANSI: 6 [ 114.474342] sd 5:0:0:0: [sdb] 732566645 4096-byte logical blocks: (3.00 TB/2.72 TiB) [ 114.475089] sd 5:0:0:0: [sdb] Write Protect is off [ 114.475092] sd 5:0:0:0: [sdb] Mode Sense: 43 00 00 00 [ 114.475959] sd 5:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 114.477093] sd 5:0:0:0: [sdb] 732566645 4096-byte logical blocks: (3.00 TB/2.72 TiB) [ 114.501649] sdb: sdb1 [ 114.502717] sd 5:0:0:0: [sdb] 732566645 4096-byte logical blocks: (3.00 TB/2.72 TiB) [ 114.504354] sd 5:0:0:0: [sdb] Attached SCSI disk [ 116.804408] EXT4-fs (sdb1): ext4_check_descriptors: Checksum for group 3976 failed (47397!=61519) [ 116.804413] EXT4-fs (sdb1): group descriptors corrupted! ... So I went and fired up my favorite partition manager - gparted, and told it to verify and repair the partition sdb1. This made gparted call e2fsck (version 1.42.4 (12-Jun-2012)) e2fsck -f -y -v /dev/sdb1 Although gparted called e2fsck with the "-v" option, sadly it doesn't show me the output of my e2fsck process (bugreport https://bugzilla.gnome.org/show_bug.cgi?id=467925 ) I started this whole thing on Sunday (2012-11-04_2200) evening, so about 48 hours ago, this is what htop says about it now (2012-11-06-1900): PID USER PRI NI VIRT RES SHR S CPU% MEM% TIME+ Command 3704 root 39 19 1560M 1166M 768 R 98.0 19.5 42h56:43 e2fsck -f -y -v /dev/sdb1 Now I found a few posts on the internet that discuss e2fsck running slow, for example: http://gparted-forum.surf4.info/viewtopic.php?id=13613 where they write that its a good idea to see if the disk is just that slow because maybe its damaged, and I think these outputs tell me that this is not the case in my case: kaefert@blechmobil:~$ sudo hdparm -tT /dev/sdb /dev/sdb: Timing cached reads: 3562 MB in 2.00 seconds = 1783.29 MB/sec Timing buffered disk reads: 82 MB in 3.01 seconds = 27.26 MB/sec kaefert@blechmobil:~$ sudo hdparm /dev/sdb /dev/sdb: multcount = 0 (off) readonly = 0 (off) readahead = 256 (on) geometry = 364801/255/63, sectors = 5860533160, start = 0 However, although I can read quickly from that disk, this disk speed doesn't seem to be used by e2fsck, considering tools like gkrellm or iotop or this: kaefert@blechmobil:~$ iostat -x Linux 3.2.0-2-amd64 (blechmobil) 2012-11-06 _x86_64_ (2 CPU) avg-cpu: %user %nice %system %iowait %steal %idle 14,24 47,81 14,63 0,95 0,00 22,37 Device: rrqm/s wrqm/s r/s w/s rkB/s wkB/s avgrq-sz avgqu-sz await r_await w_await svctm %util sda 0,59 8,29 2,42 5,14 43,17 160,17 53,75 0,30 39,80 8,72 54,42 3,95 2,99 sdb 137,54 5,48 9,23 0,20 587,07 22,73 129,35 0,07 7,70 7,51 16,18 2,17 2,04 Now I researched a little bit on how to find out what e2fsck is doing with all that processor time, and I found the tool strace, which gives me this: kaefert@blechmobil:~$ sudo strace -p3704 lseek(4, 41026998272, SEEK_SET) = 41026998272 write(4, "\212\354K[_\361\3nl\212\245\352\255jR\303\354\312Yv\334p\253r\217\265\3567\325\257\3766"..., 4096) = 4096 lseek(4, 48404766720, SEEK_SET) = 48404766720 read(4, "\7t\260\366\346\337\304\210\33\267j\35\377'\31f\372\252\ffU\317.y\211\360\36\240c\30`\34"..., 4096) = 4096 lseek(4, 41027002368, SEEK_SET) = 41027002368 write(4, "\232]7Ws\321\352\t\1@[+5\263\334\276{\343zZx\352\21\316`1\271[\202\350R`"..., 4096) = 4096 lseek(4, 48404770816, SEEK_SET) = 48404770816 read(4, "\17\362r\230\327\25\346//\210H\v\311\3237\323K\304\306\361a\223\311\324\272?\213\tq \370\24"..., 4096) = 4096 lseek(4, 41027006464, SEEK_SET) = 41027006464 write(4, "\367yy>x\216?=\324Z\305\351\376&\25\244\210\271\22\306}\276\237\370(\214\205G\262\360\257#"..., 4096) = 4096 lseek(4, 48404774912, SEEK_SET) = 48404774912 read(4, "\365\25\0\21|T\0\21}3t_\272\373\222k\r\177\303\1\201\261\221$\261B\232\3142\21U\316"..., 4096) = 4096 ^CProcess 3704 detached around 16 of these lines every second, so 4 read and 4 write operations every second, which I don't consider to be a lot.. And finally, my question: Will this process ever finish? If those numbers from fseek (48404774912) represent bytes, that would be something like 45 gigabytes, with this beeing a 3 terrabyte disk, which would give me 134 days to go, if the speed stays constant, and e2fsck scans the disk like this completly and only once. Do you have some advice for me? I have most of the data on that disk elsewhere, but I've put a lot of hours into sorting and merging it to this disk, so I would prefer to getting this disk up and running again, without formatting it anew. I don't think that the hardware is damaged since the disk is only a few months and since I can't see any I/O errors in the dmesg output. UPDATE: I just looked at the strace output again (2012-11-06_2300), now it looks like this: lseek(4, 1419860611072, SEEK_SET) = 1419860611072 read(4, "3#\f\2447\335\0\22A\355\374\276j\204'\207|\217V|\23\245[\7VP\251\242\276\207\317:"..., 4096) = 4096 lseek(4, 43018145792, SEEK_SET) = 43018145792 write(4, "]\206\231\342Y\204-2I\362\242\344\6R\205\361\324\177\265\317C\334V\324\260\334\275t=\10F."..., 4096) = 4096 lseek(4, 1419860615168, SEEK_SET) = 1419860615168 read(4, "\262\305\314Y\367\37x\326\245\226\226\320N\333$s\34\204\311\222\7\315\236\336\300TK\337\264\236\211n"..., 4096) = 4096 lseek(4, 43018149888, SEEK_SET) = 43018149888 write(4, "\271\224m\311\224\25!I\376\16;\377\0\223H\25Yd\201Y\342\r\203\271\24eG<\202{\373V"..., 4096) = 4096 lseek(4, 1419860619264, SEEK_SET) = 1419860619264 read(4, ";d\360\177\n\346\253\210\222|\250\352T\335M\33\260\320\261\7g\222P\344H?t\240\20\2548\310"..., 4096) = 4096 lseek(4, 43018153984, SEEK_SET) = 43018153984 write(4, "\360\252j\317\310\251G\227\335{\214`\341\267\31Y\202\360\v\374\307oq\3063\217Z\223\313\36D\211"..., 4096) = 4096 So the numbers in the lseek lines before the reads, like 1419860619264 are already a lot bigger, standing for 1.29 terabytes if those numbers are bytes, so it doesn't seem to be a linear progress on a big scale, maybe there are only some areas that need work, that have big gaps in between them. UPDATE2: Okey, big disappointment, the numbers are back to very small again (2012-11-07_0720) lseek(4, 52174548992, SEEK_SET) = 52174548992 read(4, "\374\312\22\\\325\215\213\23\0357U\222\246\370v^f(\312|f\212\362\343\375\373\342\4\204mU6"..., 4096) = 4096 lseek(4, 46603526144, SEEK_SET) = 46603526144 write(4, "\370\261\223\227\23?\4\4\217\264\320_Am\246CQ\313^\203U\253\274\204\277\2564n\227\177\267\343"..., 4096) = 4096 so either e2fsck goes over the data multiple times, or it just hops back and forth multiple times. Or my assumption that those numbers are bytes is wrong. UPDATE3: Since it's mentioned here http://forums.fedoraforum.org/showthread.php?t=282125&page=2 that you can testisk while e2fsck is running, i tried that, though not with a lot of success. When asking testdisk to display the data of my partition, this is what I get: TestDisk 6.13, Data Recovery Utility, November 2011 Christophe GRENIER <[email protected]> http://www.cgsecurity.org 1 P Linux 0 4 5 45600 40 8 732566272 Can't open filesystem. Filesystem seems damaged. And this is what strace currently gives me (2012-11-07_1030) lseek(4, 212460343296, SEEK_SET) = 212460343296 read(4, "\315Mb\265v\377Gn \24\f\205EHh\2349~\330\273\203\3375\206\10\r3=W\210\372\352"..., 4096) = 4096 lseek(4, 47347830784, SEEK_SET) = 47347830784 write(4, "]\204\223\300I\357\4\26\33+\243\312G\230\250\371*m2U\t_\215\265J \252\342Pm\360D"..., 4096) = 4096 (times are in CET)

    Read the article

  • Nginx + Nagios : 502 Bad gateway

    - by MrROY
    I have a fully new install nagios, but I can't access to it. Here's my Nginx config: server{ listen 80; server_name 61.148.45.10; # blahblah # Nagios Monitoring location /nagios3/ { proxy_pass http://127.0.0.1:80; } } Nagios is installed step by step(From this Linode guide): sudo apt-get install -y nagios3 Then I try to visit http://ip-address/nagios3/, but it shows 502 bad gateway. How do I deal with this ? This is my /var/log/syslog: Oct 25 14:18:17 my-server nagios3: SERVICE ALERT: localhost;Disk Space;WARNING;SOFT;1;DISK WARNING - free space: /boot 43 MB (20% inode=99%): Oct 25 14:19:07 my-server nagios3: SERVICE ALERT: localhost;HTTP;WARNING;SOFT;1;HTTP WARNING: HTTP/1.1 403 Forbidden - 319 bytes in 0.000 second response time Oct 25 14:19:17 my-server nagios3: SERVICE ALERT: localhost;Disk Space;WARNING;SOFT;2;DISK WARNING - free space: /boot 43 MB (20% inode=99%): Oct 25 14:20:07 my-server nagios3: SERVICE ALERT: localhost;HTTP;WARNING;SOFT;2;HTTP WARNING: HTTP/1.1 403 Forbidden - 319 bytes in 0.000 second response time Oct 25 14:20:17 my-server nagios3: SERVICE ALERT: localhost;Disk Space;WARNING;SOFT;3;DISK WARNING - free space: /boot 43 MB (20% inode=99%): Oct 25 14:21:07 my-server nagios3: SERVICE ALERT: localhost;HTTP;WARNING;SOFT;3;HTTP WARNING: HTTP/1.1 403 Forbidden - 319 bytes in 0.000 second response time Oct 25 14:21:17 my-server nagios3: SERVICE ALERT: localhost;Disk Space;WARNING;HARD;4;DISK WARNING - free space: /boot 43 MB (20% inode=99%): Oct 25 14:21:17 my-server nagios3: SERVICE NOTIFICATION: root;localhost;Disk Space;WARNING;notify-service-by-email;DISK WARNING - free space: /boot 43 MB (20% inode=99%): Oct 25 14:21:17 my-server postfix/pickup[24474]: 4F89F394034C: uid=109 from=<nagios> Oct 25 14:21:17 my-server postfix/cleanup[27756]: 4F89F394034C: message-id=<20131025062117.4F89F394034C@my-server> Oct 25 14:21:17 my-server postfix/qmgr[24475]: 4F89F394034C: from=<nagios@[email protected]>, size=594, nrcpt=1 (queue active) Oct 25 14:21:17 my-server postfix/local[27758]: 4F89F394034C: to=<root@localhost>, relay=local, delay=0.15, delays=0.11/0/0/0.04, dsn=2.0.0, status=sent (delivered to mailbox) Oct 25 14:21:17 my-server postfix/qmgr[24475]: 4F89F394034C: removed Oct 25 14:22:07 my-server nagios3: SERVICE ALERT: localhost;HTTP;WARNING;HARD;4;HTTP WARNING: HTTP/1.1 403 Forbidden - 319 bytes in 0.000 second response time Oct 25 14:22:07 my-server nagios3: SERVICE NOTIFICATION: root;localhost;HTTP;WARNING;notify-service-by-email;HTTP WARNING: HTTP/1.1 403 Forbidden - 319 bytes in 0.000 second response time Oct 25 14:22:07 my-server postfix/pickup[24474]: 219CA3940381: uid=109 from=<nagios> Oct 25 14:22:07 my-server postfix/cleanup[27756]: 219CA3940381: message-id=<20131025062207.219CA3940381@my-server> Oct 25 14:22:07 my-server postfix/qmgr[24475]: 219CA3940381: from=<nagios@[email protected]>, size=605, nrcpt=1 (queue active) Oct 25 14:22:07 my-server postfix/local[27758]: 219CA3940381: to=<root@localhost>, relay=local, delay=0.12, delays=0.07/0/0/0.05, dsn=2.0.0, status=sent (delivered to mailbox) Oct 25 14:22:07 my-server postfix/qmgr[24475]: 219CA3940381: removed Oct 25 14:39:01 my-server CRON[28242]: (root) CMD ( [ -x /usr/lib/php5/maxlifetime ] && [ -d /var/lib/php5 ] && find /var/lib/php5/ -depth -mindepth 1 -maxdepth 1 -type f -cmin +$(/usr/lib/php5/maxlifetime) ! -execdir fuser -s {} 2>/dev/null \; -delete) And there're lot of 127.0.0.1 visit in nginx log, but I actually visit from a external ip: 127.0.0.1 - - [25/Oct/2013:14:21:02 +0800] "GET /nagios3/ HTTP/1.0" 502 575 "-" "Mozilla/5.0 (Macintosh; Intel Mac OS X 10_8_5) AppleWebKit/537.36 (KHTML, like Gecko) Chrome/3 0.0.1599.69 Safari/537.36" 127.0.0.1 - - [25/Oct/2013:14:21:02 +0800] "GET /nagios3/ HTTP/1.0" 502 575 "-" "Mozilla/5.0 (Macintosh; Intel Mac OS X 10_8_5) AppleWebKit/537.36 (KHTML, like Gecko) Chrome/3 0.0.1599.69 Safari/537.36" 127.0.0.1 - - [25/Oct/2013:14:21:02 +0800] "GET /nagios3/ HTTP/1.0" 502 575 "-" "Mozilla/5.0 (Macintosh; Intel Mac OS X 10_8_5) AppleWebKit/537.36 (KHTML, like Gecko) Chrome/3 0.0.1599.69 Safari/537.36"

    Read the article

  • Increase samba space on open suse 12.1

    - by Kapil Sharma
    I know linux basics but not an expert. IT guy left the job here and there is some time before new hire. So sorry if question is very basic. We have local testing server based on Open SUSE 12.1, which also act as shared drive between dev/mgmt team here and using Samba for that. Now we are running out of space on samba, even though server's 2*1TB harddisk is nearly 90% free. My question is, what is limiting Samba and how can I increase its limit? We need around at least 500 GB as shared drive but currently its just 25 GB. I don't need step by step answer, just a link to any helpful article would be sufficient. Probably I'm putting wrong keywords in google so not getting any helpful link. EDIT: Output of commands in the first comment. All commands were run as root user df -h (getting error with df -ht) Filesystem Size Used Avail Use% Mounted on rootfs 30G 5.1G 23G 19% / devtmpfs 2.0G 36K 2.0G 1% /dev tmpfs 2.0G 1.1M 2.0G 1% /dev/shm tmpfs 2.0G 676K 2.0G 1% /run /dev/sda2 30G 5.1G 23G 19% / tmpfs 2.0G 0 2.0G 0% /sys/fs/cgroup tmpfs 2.0G 676K 2.0G 1% /var/run tmpfs 2.0G 0 2.0G 0% /media tmpfs 2.0G 676K 2.0G 1% /var/lock /dev/sda3 36G 31G 3.3G 91% /home fdisk -l /dev/[hmsv]d* Disk /dev/sda: 80.0 GB, 80026361856 bytes 255 heads, 63 sectors/track, 9729 cylinders, total 156301488 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x2d4a2d49 Device Boot Start End Blocks Id System /dev/sda1 2048 16771071 8384512 82 Linux swap / Solaris /dev/sda2 * 16771072 79681535 31455232 83 Linux /dev/sda3 79681536 156301311 38309888 83 Linux Disk /dev/sda1: 8585 MB, 8585740288 bytes 255 heads, 63 sectors/track, 1043 cylinders, total 16769024 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Disk /dev/sda1 doesn't contain a valid partition table Disk /dev/sda2: 32.2 GB, 32210157568 bytes 255 heads, 63 sectors/track, 3915 cylinders, total 62910464 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Device Boot Start End Blocks Id System Disk /dev/sda3: 39.2 GB, 39229325312 bytes 255 heads, 63 sectors/track, 4769 cylinders, total 76619776 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Disk /dev/sda3 doesn't contain a valid partition table vgs No volume groups found lvs No volume groups found output of vi /etc/samba/smb.conf # smb.conf is the main Samba configuration file. You find a full commented # version at /usr/share/doc/packages/samba/examples/smb.conf.SUSE if the # samba-doc package is installed. # Date: 2011-11-02 [global] workgroup = WORKGROUP passdb backend = tdbsam printing = cups printcap name = cups printcap cache time = 750 cups options = raw map to guest = Bad User include = /etc/samba/dhcp.conf logon path = \\%L\profiles\.msprofile logon home = \\%L\%U\.9xprofile logon drive = P: usershare allow guests = Yes [homes] comment = Home Directories valid users = %S, %D%w%S browseable = No read only = No inherit acls = Yes [profiles] comment = Network Profiles Service path = %H read only = No store dos attributes = Yes create mask = 0600 directory mask = 0700 [users] comment = All users path = /home read only = No inherit acls = Yes veto files = /aquota.user/groups/shares/ [groups] comment = All groups path = /home/groups read only = No inherit acls = Yes [printers] comment = All Printers path = /var/tmp printable = Yes create mask = 0600 browseable = No [print$] comment = Printer Drivers path = /var/lib/samba/drivers write list = @ntadmin root force group = ntadmin create mask = 0664 directory mask = 0775 [allusers] comment = All Users path = /home/shares/allusers valid users = @users force group = users create mask = 0660 directory mask = 0771 writable = yes

    Read the article

  • How do I make an external hard drive keep the same drive letter permanently?

    - by andygrunt
    I have a desktop PC (2002 vintage) running Windows XP that I turn on about 2 or 3 times per week. I have a mains powered 250Gb Western Digital hard disk connected to it via USB. I always turn the hard disk on before the PC so it's up and running as the PC boots. When I first connected the external hard disk, the PC assigned it a letter ('i' if it matters) and I've installed software to it, created shortcuts to various files and folders on the disk using that letter. For years everything was fine then I would boot the PC and the hard disk was assigned a different letter. I'd then have to go into 'my computer/manage/disk management' and manually change the letter back to 'i'. If I then rebooted the PC, the hard disk would usually still be 'i' but after the next reboot would be some other random letter and I have to manually change it back to 'i'. This would go on for some time then there'd be periods when the it would always be 'i' then, for no apparent reason (no new devices added, for example), the drive letter would start changing again. At the moment it's in random drive letter mood so I thought I'd ask the following question... How do I assign the external hard disk to be 'i' permanently? Answer: Thanks Molly that seems to have done the trick (after a little fiddling) - slightly disappointed there wasn't a way to do it within Windows without installing something else though. For anyone else trying this, it wasn't completely straightforward so here's what happened with me. I installed USBDLM as per the instructions on its website. I guessed that I had to assign the first USB letter to i so replaced the 'Letter1=' lines to 'Letter=I' in the ini file. To test it, I rebooted the PC only to find it came back up with the display set to 640x480 in 16 colours. After some investigation, I re-installed the display drivers and rebooted and set the display back to its usual setting. The external hard disk now gets set to 'i' but I found I had to re-apply sharing status to it so it was seen from my laptop which is on the same network. The end result of all this is that it now does what I wanted although it does act as though the hard drive has just been plugged in a few seconds after the Windows desktop appears i.e. the little box appears with a progress bar as it searches through the contents of the 'new' hard drive and I eventually get a dialogue box saying 'This disk or device contains more than one type of content. What do you want Windows to do?' and lists options such as play media files, print the pictures or open folder to view the files. This is a tiny pain I wish didn't happen but not exactly a huge price to pay. Other than that - it seems to work fine :) Looks like a spoke too soon... Every time I reboot, I have to re-share the 'i' drive (which I didn't have to do before) so it can be seen by my laptop on the same network. Any ideas how to make that permanent?

    Read the article

  • help: cannot make ubuntu 64-bit v12.04 install work

    - by honestann
    I decided it was time to update my ubuntu (single boot) computer from 64-bit v10.04 to 64-bit v12.04. Unfortunately, for some reason (or reasons) I just can't make it work. Note that I am attempting a fresh install of 64-bit v12.04 onto a new 3TB hard disk, not an upgrade of the 1TB hard disk that has contained my 64-bit v10.04 installation. To perform the attempted install of v12.04 I unplug the SATA cable from the 1TB drive and plug it into the 3TB drive (to avoid risking damage to my working v10.04 installation). I downloaded the ubuntu 64-bit v12.04 install DVD ISO file (~1.6 GB) from the ubuntu releases webpage and burned it onto a DVD. I have downloaded the DVD ISO file 3 times and burned 3 of these installation DVDs (twice with v10.04 and once with my winxp64 system), but none of them work. I run the "check disk" on the DVDs at the beginning of the installation process to assure the DVD is valid. I also tried to install on two older 250GB seagate drives in the same computer. During every attempt I plug the same SATA cable (sda) into only one disk drive (the 3TB or one of the 250GB drives) and leave the other disk drives unconnected (for simplicity). Installation takes about 30 minutes on the 250GB drives, and about 60 minutes on the 3TB drive - not sure why. When I install on the 250GB drives, the install process finishes, the computer reboots (after the install DVD is removed), but I get a grub error 15. It is my understanding that 64-bit ubuntu (and 64-bit linux in general) has no problem with 3TB disk drives. In the BIOS I have tried having EFI set to "enabled" and "auto" with no apparent difference (no success). I have tried partitioning the drive in a few ways to see if that makes a difference, but so far it has not mattered. Typically I manually create partitions something like this: 8GB swap 8GB /boot ext4 3TB / ext4 But I've also tried the following, just in case it matters: 100MB boot efi 8GB swap 8GB /boot ext4 3TB / ext4 Note: In the partition dialog I specify bootup on the same drive I am partitioning and installing ubuntu v12.04 onto. It is a VERY DANGEROUS FACT that the default for this always comes up with the wrong drive (some other drive, generally the external drive). Unless I'm stupid or misunderstanding something, this is very wrong and very dangerous default behavior. Note: If I connect the SATA cable to the 1TB drive that has been my ubuntu 64-bit v10.04 system drive for the past 2 years, it boots up and runs fine. I guess there must be a log file somewhere, and maybe it gives some hints as to what the problem is. I should be able to boot off the 1TB drive with the 3TB drive connected as a secondary (non-boot) drive and get the log file, assuming there is one and someone tells me the name (and where to find it if the name is very generic). After installation on the 3TB drive completes and the system reboots, the following prints out on a black screen: Loading Operating System ... Boot from CD/DVD : Boot from CD/DVD : error: unknown filesystem grub rescue Note: I have two DVD burners in the system, hence the duplicate line above. The same install and reboot on the 250GB drives generates "grub error 15". Sigh. Any ideas? ========== motherboard == gigabyte 990FXA-UD7 CPU == AMD FX-8150 8-core bulldozer @ 3.6 GHz RAM == 8GB of DDR3 in 2 sticks (matched pair) HDD == seagate 3TB SATA3 @ 7200 rpm (new install 64-bit v12.04) HDD == seagate 1TB SATA3 @ 7200 rpm (current install 64-bit v10.04) GPU == nvidia GTX-285 ??? == no overclocking or other funky business USB == external seagate 2TB HDD for making backups DVD == one bluray burner (SATA) DVD == one DVD burner (SATA) The current ubuntu 64-bit v10.04 system boots and runs fine on a seagate 1TB.

    Read the article

  • SQL Server Transaction Marks: Restoring multiple databases to a common relative point

    - by Mladen Prajdic
    We’re all familiar with the ability to restore a database to point in time using the RESTORE WITH STOPAT statement. But what if we have multiple databases that are accessed from one application or are modifying each other? And over multiple instances? And all databases have different workloads? And we want to restore all of the databases to some known common relative point? The catch here is that this common relative point isn’t the same point in time for all databases. This common relative point in time might be now in DB1, now-1 hour in DB2 and yesterday in DB3. And we don’t know the exact times. Let me introduce you to Transaction Marks. When we run a marked transaction using the WITH MARK option a flag is set in the transaction log and a row is added to msdb..logmarkhistory table. When restoring a transaction log backup we can restore to either before or after that marked transaction. The best thing is that we don’t even need to have one database modifying another database. All we have to do is use a marked transaction with the same name in different database. Let’s see how this works with an example. The code comments say what’s going on. USE master GOCREATE DATABASE TestTxMark1GOUSE TestTxMark1GOCREATE TABLE TestTable1( ID INT, VALUE UNIQUEIDENTIFIER) -- insert some data into the table so we can have a starting pointINSERT INTO TestTable1SELECT ROW_NUMBER() OVER(ORDER BY number) AS RN, NULLFROM master..spt_valuesORDER BY RNSELECT *FROM TestTable1GO-- TAKE A FULL BACKUP of the databseBACKUP DATABASE TestTxMark1 TO DISK = 'c:\TestTxMark1.bak'GO USE master GOCREATE DATABASE TestTxMark2GOUSE TestTxMark2GOCREATE TABLE TestTable2( ID INT, VALUE UNIQUEIDENTIFIER)-- insert some data into the table so we can have a starting pointINSERT INTO TestTable2SELECT ROW_NUMBER() OVER(ORDER BY number) AS RN, NEWID()FROM master..spt_valuesORDER BY RNSELECT *FROM TestTable2GO-- TAKE A FULL BACKUP of our databseBACKUP DATABASE TestTxMark2 TO DISK = 'c:\TestTxMark2.bak'GO -- start a marked transaction that modifies both databasesBEGIN TRAN TxDb WITH MARK -- update values from NULL to random value UPDATE TestTable1 SET VALUE = NEWID(); -- update first 100 values from random value -- to NULL in different DB UPDATE TestTxMark2.dbo.TestTable2 SET VALUE = NULL WHERE ID <= 100;COMMITGO     -- some time goes by here -- with various database activity... -- We see two entries for marks in each database. -- This is just informational and has no bearing on the restore itself.SELECT * FROM msdb..logmarkhistory USE masterGO-- create a log backup to restore to mark pointBACKUP LOG TestTxMark1 TO DISK = 'c:\TestTxMark1.trn'GO-- drop the database so we can restore it backDROP DATABASE TestTxMark1GO USE masterGO-- create a log backup to restore to mark pointBACKUP LOG TestTxMark2 TO DISK = 'c:\TestTxMark2.trn'GO-- drop the database so we can restore it backDROP DATABASE TestTxMark2GO -- RESTORE THE DATABASE BACK BEFORE OUR TRANSACTION-- restore the full backup RESTORE DATABASE TestTxMark1 FROM DISK = 'c:\TestTxMark1.bak' WITH NORECOVERY;-- restore the log backup to the transaction markRESTORE LOG TestTxMark1 FROM DISK = 'c:\TestTxMark1.trn' WITH RECOVERY, -- recover to state before the transaction STOPBEFOREMARK = 'TxDb'; -- recover to state after the transaction -- STOPATMARK = 'TxDb';GO -- RESTORE THE DATABASE BACK BEFORE OUR TRANSACTION-- restore the full backup RESTORE DATABASE TestTxMark2 FROM DISK = 'c:\TestTxMark2.bak' WITH NORECOVERY;-- restore the log backup to the transaction markRESTORE LOG TestTxMark2 FROM DISK = 'c:\TestTxMark2.trn' WITH RECOVERY, -- recover to state before the transaction STOPBEFOREMARK = 'TxDb'; -- recover to state after the transaction -- STOPATMARK = 'TxDb';GO USE TestTxMark1-- we restored to time before the transaction -- so we have NULL values in our tableSELECT * FROM TestTable1 USE TestTxMark2-- we restored to time before the transaction -- so we DON'T have NULL values in our tableSELECT * FROM TestTable2   Transaction marks can be used like a crude sync mechanism for cross database operations. With them we can mark our databases with a common “restore to” point so we know we have a valid state between all databases to restore to.

    Read the article

  • Add IPv6 support to DirectAdmin server

    - by George Boot
    I just set up an new DirectAdmin, and I want to prepare it for IPv6 use. My ISP have gave me an range of IPv6 addresses that I can use. Lets say that address is 2a01:7c8:**:1f::. My neworkadapter user DHCP to resolves its IP-addresses. When i type ifoncig eth0 I get the following result: eth0 Link encap:Ethernet HWaddr 52:**:**:**:ce:f3 inet addr:37.**.**.44 Bcast:37.**.**.255 Mask:255.255.255.0 inet6 addr: 2a01:7c8:****:1f::/64 Scope:Global inet6 addr: fe80::5054:ff:fe87:cef3/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:38941 errors:0 dropped:0 overruns:0 frame:0 TX packets:29439 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:3779534 (3.6 MiB) TX bytes:5089379 (4.8 MiB) As you can see, I have an IPv6 address set, but I can't ping6 an IPv6 host. I get the error: connect: Network is unreachable. I decided that I needed an gateway, so I tryed to add one: ip -6 route add default via 2a01:7c8:****::1 dev eth0 (2a01:7c8:**::1 is the gateway of my ISP). But it trows an error: RTNETLINK answers: No route to host. Does somebody know what to do, and how to solve this issue? Thanks a lot!

    Read the article

  • OBIEE 11.1.1 - OBIEE 11g Full Sample App on VMware Player 4

    - by user809526
    The Full Sample App is designed to run on Virtual Box. Let's describe how to run it on VMware Player 4. Open Virtualization Format Tool http://communities.vmware.com/community/vmtn/server/vsphere/automationtools/ovf VMware Player Documentation https://www.vmware.com/support/pubs/player_pubs.html Full Sample App Deployment Guide sampleapp107-vbimage-deployguide-453583.pdf INSTALL VMplayer 4.0.0 as root LINUX # sh VMware-Player-4.0.0-471780.x86_64.bundle (A new VM is not needed and can be deleted later after that installation is completed. "I will install OS later" - blank hard disk Guest: linux, Red Hat Enterprise Linux 5-64bits => rename to RHEL target: eg /a/root/vmware/ Max disk size: 5 GB (will be deleted) Disk: Single file Dummy RHEL.vmk, RHEL.vmdk is generated. "Delete VM from Disk" in VM Player.) Copy Full Sample App files to target /a/root/vmware/ WARNING: Select a target eg /a/root/vmware/ with lots of free space, 95 GB. Check checksums (md5sum). Please do it! ff85c7eacf7fb8c382e98da875e879e1  Sampleapp_v107_GA-disk1.vmdk 973258cb3c7d64ab03ae853278cf2233  Sampleapp_v107_GA-disk2.vmdk e576be16e36d810479736bfb15d050f5  Sampleapp_v107_GA-disk3.vmdk 3455df77279e53e07d5fee6712f1597d  Sampleapp_v107_GA-disk4.vmdk OVF FILE   Sampleapp_v107_GA.ovf CONVERSION $ cd /a/root/vmware/ LINUX $ /usr/bin/ovftool -tt=ovf --compress=1 -dm=monolithicSparse Sampleapp_v107_GA.ovf .  [dot] Opening OVF source: Sampleapp_v107_GA.ovf Warning: No manifest file Opening OVF target: . Writing OVF package: Sampleapp_v107_GA/Sampleapp_v107_GA.ovf Disk Transfer Completed                   Completed successfully WINDOWS CYGWIN $ /cygdrive/c/VMwarePlayer/OVFTool/ovftool.exe -tt=ovf --compress=1 -dm=monolithicSparse Sampleapp_v107_GA.ovf .  [dot] Opening OVF source: Sampleapp_v107_GA.ovf Warning: No manifest file Opening OVF target: . Writing OVF package: Sampleapp_v107_GA\Sampleapp_v107_GA.ovf Disk Transfer Completed Completed successfully /a/root/vmware$ du -sk 49095328    .   [50 GB already occupied] IMPORT - First start of VM Player 4: /usr/bin/vmplayer "Open a Virtual Machine" Browse to /a/root/vmware/Sampleapp_v107_GA/Sampleapp_v107_GA.ovf [the new generated .ovf] "Import Virtual Machine" dialog Name: Sampleapp_v107_GA Location: /a/root/vmware/Sampleapp_v107_GA/storage [was /home/tdubois/vmware/Sampleapp_v107_GA] "Import" "The import failed because /a/root/vmware/Sampleapp_v107_GA/Sampleapp_v107_GA.ovf did not pass OVF specification conformance or virtual hardware compliance checks. Click Retry to relax OVF specification..." "Retry" ; Long import /a/root/vmware/Sampleapp_v107_GA/storage/Sampleapp_v107_GA.vmx and new .vmdk files are created. /a/root/vmware$ du -sk 95551384    .   [95 GB occupied] Full Sample App GUEST SETUP "Edit VM settings" min 3GB, 2+ processors, network bridged. For OBIEE + Essbase testing use 8 GB RAM hardware. At first time lauch of Full Sample App, leave OEL booting for several minutes undisturbed. Problem with X display server may occur [/usr/bin/Xorg ; man Xorg]. "Failed to start the X server.... Would you like to view the X server output to diagnose the problem?" "No" [tab key] "Would you like to try to configure the X server? Note that you will need the root password for this." "Yes" [oracle] X Display Settings 800x600 saved in /etc/X11/xorg.conf "Trying to restart the X server" Login as root/oracle in guest OEL. In guest OEL, Virtual Machine > Install VMware Tools... Extract archive VMwareTools-8.8.0-471268.tar.gz all files in writable local directory eg /root In Terminal run Perl script # cd /root/vmware-tools-distrib ; ./vmware-install.pl [keep all default answers] Set keyboard layout System > Preferences > Keyboard > Layouts Restart X server eg System > Log Out root... , relogin Modify X resolution System > Preferences > Screen Resolution Full Sample App OEL login: oracle/oracle ; root/oracle [default US keyboard layout] Credentials are described in the 'sampleapp107-vbimage-deployguide-453583.pdf' The large files in /a/root/vmware/ /a/root/vmware/Sampleapp_v107_GA/ may be removed. FAILURE REMARK: Adding the 4 original Sampleapp_v107_GA-disks[1234].vmdk to VM Player does NOT work as described below. "Edit VM settings" "Remove" "Hard Disk" "Edit VM settings" "Add" "Hard Disk" "Next" "Use an existing virtual disk" "Browse" "Finish" "Keep existing format" "Ok" for each 4 disks settings one by one. Start VM Player 4. "You do not have write access to a partition" Allow all Sampleapp_v107 OEL linux launches. OEL stalls silently after 'Checking filesystems'.

    Read the article

  • 8 Mac System Features You Can Access in Recovery Mode

    - by Chris Hoffman
    A Mac’s Recovery Mode is for more than just reinstalling Mac OS X. You’ll find many other useful troubleshooting utilities here — you can use these even if your Mac can’t boot normally. To access Recovery Mode, restart your Mac and press and hold the Command + R keys during the boot-up process. This is one of several hidden startup options on a Mac. Reinstall Mac OS X Most people know Recovery Mode as the place you go to reinstall OS X on your Mac. Recovery Mode will download the OS X installer files from teh Intenret if you don’t have them locally, so they don’t take up space on your disk and you’ll never have to hunt for an opearign system disc. Better yet, it will download up-to-date installation files so you don’t have to spend hours installing operating system updates later. Microsoft could learn a lot from Apple here. Restore From a Time Machine Backup Instead of reinstalling OS X, you can choose to restore your Mac from a time machine backup. This is like restoring a system image on another operating system. You’ll need an external disk containing a backup image created on the current computer to do this. Browse the Web The Get Help Online link opens the Safari web browser to Apple’s documentation site. It’s not limited to Apple’s website, though — you can navigate to any website you like. This feature allows you to access and use a browser on your Mac even if it isn’t booting properly. It’s ideal for looking up troubleshooting information. Manage Your Disks The Disk Utility option opens the same Disk Utility you can access from within Mac OS X. It allows you to partition disks, format them, scan disks for problems, wipe drives, and set up drives in a RAID configuration. If you need to edit partitions from outside your operating system, you can just boot into the recovery environment — you don’t have to download a special partitioning tool and boot into it. Choose the Default Startup Disk Click the Apple menu on the bar at the top of your screen and select Startup Disk to access the Choose Startup Disk tool. Use this tool to choose your computer’s default startup disk and reboot into another operating system. For example, it’s useful if you have Windows installed alongside Mac OS X with Boot Camp. Add or Remove an EFI Firmware Password You can also add a firmware password to your Mac. This works like a BIOS password or UEFI password on a Windows or Linux PC. Click the Utilities menu on the bar at the top of your screen and select Firmware Password Utility to open this tool. Use the tool to turn on a firmware password, which will prevent your computer from starting up from a different hard disk, CD, DVD, or USB drive without the password you provide. This prevents people form booting up your Mac with an unauthorized operating system. If you’ve already enabled a firmware password, you can remove it from here. Use Network Tools to Troubleshoot Your Connection Select Utilities > Network Utility to open a network diagnostic tool. This utility provides a graphical way to view your network connection information. You can also use the netstat, ping, lookup, traceroute, whois, finger, and port scan utilities from here. These can be helpful to troubleshoot Internet connection problems. For example, the ping command can demonstrate whether you can communicate with a remote host and show you if you’re experiencing packet loss, while the traceroute command can show you where a connection is failing if you can’t connect to a remote server. Open a Terminal If you’d like to get your hands dirty, you can select Utilities > Terminal to open a terminal from here. This terminal allows you to do more advanced troubleshooting. Mac OS X uses the bash shell, just as typical Linux distributions do. Most people will just need to use the Reinstall Mac OS X option here, but there are many other tools you can benefit from. If the Recovery Mode files on your Mac are damaged or unavailable, your Mac will automatically download them from Apple so you can use the full recovery environment.

    Read the article

  • Mounting ddrescue image after recovery (in over my head)

    - by BorgDomination
    I'm having problems mounting the recovery image. I've tried to mount the image multiple ways. quark@DS9 ~ $ sudo mount -t ext4 /media/jump1/1recover/sdb1.img /mnt mount: wrong fs type, bad option, bad superblock on /dev/loop0, missing codepage or helper program, or other error In some cases useful info is found in syslog - try dmesg | tail or so quark@DS9 ~ $ sudo mount -r -o loop /media/jump1/1recover/sdb1.img recover mount: you must specify the filesystem type quark@DS9 ~ $ sudo mount /media/jump1/1recover/sdb1.img mnt mount: you must specify the filesystem type It doesn't even give me detailed information on the file I just made, nautilus says it's 160gb. quark@DS9 ~ $ file /media/jump1/1recover/sdb1.img /media/jump1/1recover/sdb1.img: data quark@DS9 ~ $ mmls /media/jump1/1recover/sdb1.img Cannot determine partition type I'm not sure what I'm doing wrong or if I started this process incorrectly from the beginning. I've outlined what I've done so far below. I'm clueless, I'd appreciate if someone had some input for me. What I have done from the beginning My laptop has two hard drives. One has the dual boot Win7 / Linux Mint system files. Secondary one contained my /home folder. The laptop was jarred and the /home disk was broken. I tried a LiveCD recovery, it failed. Wouldn't even load a Live session with the disk installed. So I turned to ddrescue. quark@DS9 ~ $ sudo fdisk -l Disk /dev/sda: 160.0 GB, 160041885696 bytes 255 heads, 63 sectors/track, 19457 cylinders, total 312581808 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x0009fc18 Device Boot Start End Blocks Id System /dev/sda1 * 2048 112642047 56320000 7 HPFS/NTFS/exFAT /dev/sda2 138033152 312580095 87273472 83 Linux /dev/sda3 112644094 138033151 12694529 5 Extended /dev/sda5 112644096 132173823 9764864 83 Linux /dev/sda6 132175872 138033151 2928640 82 Linux swap / Solaris Partition table entries are not in disk order Disk /dev/sdb: 160.0 GB, 160041885696 bytes 255 heads, 63 sectors/track, 19457 cylinders, total 312581808 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x0002a8ea Device Boot Start End Blocks Id System /dev/sdb1 * 63 312576704 156288321 83 Linux Disk /dev/sdc: 1000.2 GB, 1000204886016 bytes 255 heads, 63 sectors/track, 121601 cylinders, total 1953525168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0xed6d054b Device Boot Start End Blocks Id System /dev/sdc1 63 1953520064 976760001 7 HPFS/NTFS/exFAT sda - 160g internal, holds all system files and all computer functions. sdb - 160g internal, BROKEN, contains about 140g of data I'd like to recover. sdc - 1T external, contains recovery image. Only place that has space to do all this. From this site, https://apps.education.ucsb.edu/wiki/Ddrescue I used this script to create an image of the broken hard drive. I changed the destination to the external USB drive. #!/bin/sh prt=sdb1 src=/dev/$prt dst=/media/jump1/1recover/$prt.img log=$dst.log sudo time ddrescue --no-split $src $dst $log sudo time ddrescue --direct --max-retries=3 $src $dst $log sudo time ddrescue --direct --retrim --max-retries=3 $src $dst $log Everything looked like it came off without a hitch: quark@DS9 ~ $ sudo bash recover1 Press Ctrl-C to interrupt Initial status (read from logfile) rescued: 0 B, errsize: 0 B, errors: 0 Current status rescued: 160039 MB, errsize: 4096 B, current rate: 35588 B/s ipos: 3584 B, errors: 1, average rate: 22859 kB/s opos: 3584 B, time from last successful read: 0 s Finished 12.78user 1060.42system 1:56:41elapsed 15%CPU (0avgtext+0avgdata 4944maxresident)k 312580958inputs+0outputs (1major+601minor)pagefaults 0swaps Press Ctrl-C to interrupt Initial status (read from logfile) rescued: 160039 MB, errsize: 4096 B, errors: 1 Current status rescued: 160039 MB, errsize: 1024 B, current rate: 0 B/s ipos: 1536 B, errors: 1, average rate: 13 B/s opos: 1536 B, time from last successful read: 1.3 m Finished 0.00user 0.00system 3:43.95elapsed 0%CPU (0avgtext+0avgdata 4944maxresident)k 238inputs+0outputs (3major+374minor)pagefaults 0swaps Press Ctrl-C to interrupt Initial status (read from logfile) rescued: 160039 MB, errsize: 1024 B, errors: 1 Current status rescued: 160039 MB, errsize: 1024 B, current rate: 0 B/s ipos: 1536 B, errors: 1, average rate: 0 B/s opos: 1536 B, time from last successful read: 3.7 m Finished 0.00user 0.00system 3:43.56elapsed 0%CPU (0avgtext+0avgdata 4944maxresident)k 8inputs+0outputs (0major+376minor)pagefaults 0swaps It looks like, from where I'm standing it worked perfectly. Here's the log: # Rescue Logfile. Created by GNU ddrescue version 1.14 # Command line: ddrescue --direct --retrim --max-retries=3 /dev/sdb1 /media/jump1/1recover/sdb1.img /media/jump1/1recover/sdb1.img.log # current_pos current_status 0x00000600 + # pos size status 0x00000000 0x00000400 + 0x00000400 0x00000400 - 0x00000800 0x254314FC00 + I'm not sure how to proceed. Does this mean all of my data is lost???????? Appreciate ANY input!

    Read the article

  • Error 0x80300001 Installing Windows Server 2008 R2 64bit on FastTrak TX4660 RAID volume

    - by Konstantin Boyandin
    I am trying to install Windows Server 2008 R2 Enterprise 64bit on the following hardware: motherboard Intel DBS1200BTL Promise FastTrak TX4660 RAID controller 4 disks set up in two RAID1 arrays (handled by FastTrak) I am trying to install Windows so it would boot from RAID1 volume created with the FastTrak controller. The installation goes as in the manual, I insert the disk with the driver, select 'Browse' and specify the correct driver, it finds all the RAID arrays but notifies me that error 0x80300001 happened, Windows can't be installed on the mentioned RAID volumes, since they may not be bootable (even though the target RAID volume is the first in boot options list). If I proceed with the installation, Windows copies and unpacks itself, performs other standard actions after that. After the computer is restarted, it won't boot (Windows Boot Manager appears in the boot devices list; however, neither it nor the RAID volume itself does not boot). Is it a known problem? I can attach the boot disks to the motherboard and use its RAID capabilities instead, but I'd prefer FastTrak ones. Driver version is 1.3.0.4. Thanks.

    Read the article

  • PXE with WDS & Windows Server 2012 - no filename option in DHCP lease?

    - by user1799
    I'm trying to configure Windows Server 2012 (a virtual box VM) with WDS so I can PXE boot some Windows 7 VMs (also virtual box). All the machines involved are only attached to the "host only network", 192.168.56.0/24. The Server 2012 machine has been setup as an AD DS machine, has DNS installed and working along with DHCP with option 60 - PXEClient - set and WDS is set to not listen on DHCP ports. I've followed http://technet.microsoft.com/en-us/library/jj648426.aspx very closely. I've used the boot.wim and install.wim files from the Win 7 installation DVD and they're configured as 'boot' and 'installation' images respectively. When I boot the target machine, it gets an IP address, but I simply get 'no filename' and the boot won't proceed any further. I've tried setting option 66 to 192.168.56.2 (the WDS server) and option 67 to both Boot\x64\wdsnbp.com and Boot\x64\pxeboot.n12 but all to no avail. I can't seem to see anything in the event log, either. Can anyone out there spot what I'm doing wrong? Or give tips to narrow down a diagnostic?

    Read the article

  • Preseeding Ubuntu partman recipe using LVM and RAID

    - by Swav
    I'm trying to preseed Ubuntu 12.04 server installation and created a recipe that would create RAID 1 on 2 drives and then partition that using LVM. Unfortunately partman complains when creating LVM volumes saying there no partitions in recipe that could be used with LVM (in console it complains about unusable recipe). The layout I'm after is RAID 1 on sdb and sdc (installing from USB stick so it takes sda) and then use LVM to create boot, root and swap. The odd thing is that if I change the mount point of boot_lv to home the recipe works fine (apart from mounting in wrong place), but when mounting at /boot it fails I know I could use separate /boot primary partition, but can anybody tell me why it fails. Recipe and relevant options below. ## Partitioning using RAID d-i partman-auto/disk string /dev/sdb /dev/sdc d-i partman-auto/method string raid d-i partman-lvm/device_remove_lvm boolean true d-i partman-md/device_remove_md boolean true #d-i partman-lvm/confirm boolean true d-i partman-auto-lvm/new_vg_name string main_vg d-i partman-auto/expert_recipe string \ multiraid :: \ 100 512 -1 raid \ $lvmignore{ } \ $primary{ } \ method{ raid } \ . \ 256 512 256 ext3 \ $defaultignore{ } \ $lvmok{ } \ method{ format } \ format{ } \ use_filesystem{ } \ filesystem{ ext3 } \ mountpoint{ /boot } \ lv_name{ boot_lv } \ . \ 2000 5000 -1 ext4 \ $defaultignore{ } \ $lvmok{ } \ method{ format } \ format{ } \ use_filesystem{ } \ filesystem{ ext4 } \ mountpoint{ / } \ lv_name{ root_lv } \ . \ 64 512 300% linux-swap \ $defaultignore{ } \ $lvmok{ } \ method{ swap } \ format{ } \ lv_name{ swap_lv } \ . d-i partman-auto-raid/recipe string \ 1 2 0 lvm - \ /dev/sdb1#/dev/sdc1 \ . d-i mdadm/boot_degraded boolean true #d-i partman-md/confirm boolean true #d-i partman-partitioning/confirm_write_new_label boolean true #d-i partman/choose_partition select Finish partitioning and write changes to disk #d-i partman/confirm boolean true #d-i partman-md/confirm_nooverwrite boolean true #d-i partman/confirm_nooverwrite boolean true EDIT: After a bit of googling I found below snippet of code from partman-auto-lvm, but I still don't understand why would they prevent that setup if it's possible to do manually and booting from boot partition on LVM is possible. # Make sure a boot partition isn't marked as lvmok if echo "$scheme" | grep lvmok | grep -q "[[:space:]]/boot[[:space:]]"; then bail_out unusable_recipe fi

    Read the article

  • unreadable corrupted ntfs partition - lost clusters reported

    - by Eduardo Martinez
    partition magic is reporting multiple 'bad file record signature' and 'lost clusters' errors on my 250GB samsung sata disk (connected via usb on a xp sp3). Unfortunately PM is unable to fix. PM shows the drive as being NTFS, detects used space ok and also drive name. But PM browser (right click on partition, browse...) won't show anything (as if disk was empty) Windows Explorer is not even picking the drive name and reports 'the file or directory is corrupted and unreadable' PTDD partition table doctor demo tells me the boot sector is fine, and I can see all disk content on its browser - but crucially cannot copy that content over to a new disk (PTDD browser is pretty arid to say the least) Also tried - photorec-6.11.3 - it actually started to extract files but wouldn't keep file names or any folder structure (maybe I missed sth on the configuration options) - find and mount - intellectual scan went well, the only partition on the disk was detected, then tried to mount into p: but got this error on windows explorer: 'p:\ is not accesible. The media is write protected'. Find and mount allows you to create an image from partition but I don't have a disk big enough at hand. Does anyone know if this will keep the extracted files/folders structure intact? I'm starting to think the disk is pretty screwed and my chances to recover this data are slim. Please someone enlighten me with that marvellous piece of software I am missing :-) Thanks in advance

    Read the article

  • Disabling CPU management

    - by Tiffany Walker
    If I add the following processor.max_cstate=0 to the kernel command line for boot up, does that disable all CPU power management and throttling? I also found: http://www.experts-exchange.com/OS/Linux/Administration/A_3492-Avoiding-CPU-speed-scaling-in-modern-Linux-distributions-Running-CPU-at-full-speed-Tips.html The link talks of Change CPU governor from 'ondemand' to 'performance' for all CPUs/cores and disabling kondemand from kernel. Server is for web hosting UPDATES: 2.6.32-379.1.1.lve1.1.7.6.el6.x86_64 #1 SMP Sat Aug 4 09:56:37 EDT 2012 x86_64 x86_64 x86_64 GNU/Linux . # dmidecode 2.11 SMBIOS 2.6 present. 74 structures occupying 2878 bytes. Table at 0x0009F000. Handle 0x0000, DMI type 0, 24 bytes BIOS Information Vendor: American Megatrends Inc. Version: 1.0c Release Date: 05/27/2010 Address: 0xF0000 Runtime Size: 64 kB ROM Size: 4096 kB Characteristics: ISA is supported PCI is supported PNP is supported BIOS is upgradeable BIOS shadowing is allowed ESCD support is available Boot from CD is supported Selectable boot is supported BIOS ROM is socketed EDD is supported 5.25"/1.2 MB floppy services are supported (int 13h) 3.5"/720 kB floppy services are supported (int 13h) 3.5"/2.88 MB floppy services are supported (int 13h) Print screen service is supported (int 5h) 8042 keyboard services are supported (int 9h) Serial services are supported (int 14h) Printer services are supported (int 17h) CGA/mono video services are supported (int 10h) ACPI is supported USB legacy is supported LS-120 boot is supported ATAPI Zip drive boot is supported BIOS boot specification is supported Targeted content distribution is supported BIOS Revision: 8.16 Handle 0x0001, DMI type 1, 27 bytes System Information Manufacturer: Supermicro Product Name: X8SIE Version: 0123456789 Serial Number: 0123456789 UUID: 49434D53-0200-9033-2500-33902500D52C Wake-up Type: Power Switch SKU Number: To Be Filled By O.E.M. Family: To Be Filled By O.E.M. Handle 0x0002, DMI type 2, 15 bytes Base Board Information Manufacturer: Supermicro Product Name: X8SIE Version: 0123456789 Serial Number: VM11S61561 Asset Tag: To Be Filled By O.E.M. Features: Board is a hosting board Board is replaceable Location In Chassis: To Be Filled By O.E.M. Chassis Handle: 0x0003 Type: Motherboard Contained Object Handles: 0 Handle 0x0003, DMI type 3, 21 bytes Chassis Information Manufacturer: Supermicro Type: Sealed-case PC Lock: Not Present Version: 0123456789 Serial Number: 0123456789 Asset Tag: To Be Filled By O.E.M. Boot-up State: Safe Power Supply State: Safe Thermal State: Safe Security Status: None OEM Information: 0x00000000 Height: Unspecified Number Of Power Cords: 1 Contained Elements: 0

    Read the article

  • Ghost Solution Suite: Booting over PXE to WinPE for re-imaging, then booting to installed OS

    - by uberdanzik
    I have 40 networked computers that need to be re-imaged each night over a network via an automatic and unattended process. This is to reset the computers to a default state, as well as update the computers to the latest software loads. I'm using Symantec Ghost Solution Suite 2.5. My process so far is the following: Client begins in a powered down WakeOnLan accepting state. Ghost Console task uses WakeOnLan and PXE to boot the client into the WinPE environment. The client connects to the ghost console and reimages itself successfully. The client closes WinPE and restarts. PROBLEM: The client boots into the WinPE environment again, instead of the newly installed OS (Win7) I need it to boot into Win7 once so that I can run a few configuration batch files, then shut down into the WakeOnLan state again. Ghost console even reports an error on the process, that it never rebooted into the OS. Right now it seems that there is not an option to stop it from booting into the PXE server's WinPE image after re-imaging. Even if I set up a PXE boot menu with other boot options, its pointless, because it will always boot the default option. I would expect the ghost console task to be able to influence the PXE boot choice somehow. What do they expect us to do, turn the PXE server on and off manually? How can I get the client to boot to the OS after re-imaging? Thank you.

    Read the article

  • Does Hyper-V support SCSI Pass-through discs in a Server 2003 R2 VM?

    - by Peter Bernier
    I'm running into some difficulties getting pass-through disks to be accessible to a Hyper-v server 2003 r2 virtual machine. Host OS : Server 2008 R2 full w/Hyper-V role Guest OS : Server 2003 R2 (Windows Home Server) The guest's OS disk is a pass-through disk on the IDE controller (not the best solution, but I can live with it). My storage disks will be pass-through disks on the SCSI controller. I'm able to see all of the disks that I'll be using for the VM on the host without issue. The problem that I'm having is that I can't seem to get the guest OS to be able to 'see' the storage drives (as pass-through disks on the SCSI controller). Here's what I'm doing : On the host, the storage drive is set to 'Offline' just like the OS disk (this is required for pass-through to work). In the VM, the storage drive is on the SCSI controller. Hyper-V Integration Tools are installed in guest. That's as far as I'm able to get. I don't see the drive in Computer Management, or in Windows Explorer (I've tried with an unformatted disk, as well as after formatting a partition). I am able to see a removable device that lists the disk's model number in the Guest, but I can't seem to access the storage. (I get an entry in Device Manager that needs drivers, but nothing on the Integration Tools disc works..) Trouble-shooting steps I've tried : If put the pass-through drive on the IDE controller, I can see it in the Guest. If put the storage drive 'Online' in the host and create a VHD on it on the SCSI controller, I can see it in the Guest. I suppose I could create a fixed-size VHD that consumes the entire disk, but I'd rather not have that overhead. I've also extracted the contents of the Integration Tools drivers (x86 and amd64) and tried pointing the disk controller to each of those, with no luck. Can anyone offer suggestions as to how I can get this to work properly?

    Read the article

  • 32bit SQLServer with AWE NOT enabled. Buffer Cache Hit Ratio High, Disk Read Queue VERY HIGH, WHY?

    - by chenwq
    We have a "SQLServer 2005 SP3 32bit Enterprise Edition" running on a 32 bit Windows 2003 32bit Enterprise Edition 12GB RAM with AWE enabled using RAID5(5 pysical disks). We tuned AWE to enabled and restart sqlserver this afternoon after work, hope the performance will be better than old time. But there is something that we are very confused. On working days, SQLServer has a very bad performance. When we are looking for reasons, we check Windows Performance counter. Avg. Disk Read Queue Lenght > 140 Avg. Disk Write Queue Length < 1 SQL Server Buffer Cache Hit Ratio > 96% %Processor Time < 30% SQL Server Total Server Memory < 1.8G Obviously, without AWE enabled, SQL Server can use only less than 2G memory. My Question is: why "SQL Server Total server Memory" is less than 2G?I think SQL Server will use all 2G process address space. Does this counter count anything out? we known that sql server is sufferring lack of memory, but why "buffer hit ratio“ is as high as 96? Any advice is welcomed!

    Read the article

facebook twitter digg google delicious technorati stumbleupon myspace wordpress linkedin gmail igoogle windows live tumblr viadeo yahoo buzz yahoo mail yahoo bookmarks favorites email print

< Previous Page | 208 209 210 211 212 213 214 215 216 217 218 219  | Next Page >