Search Results

Search found 6201 results on 249 pages for 'dotnetnuke tips'.

Page 212/249 | < Previous Page | 208 209 210 211 212 213 214 215 216 217 218 219  | Next Page >

  • How to improve Samba performance on VirtualBox machine?

    - by ColinM
    I am running a Windows 7 64bit host and Ubuntu 9.04 32bit guest inside of VirtualBox 4.0.0 on a laptop which has internet connectivity via Wifi. The main use is writing code for which I use Netbeans. My dev environment is hte virtual machine and I use Samba on the VM to share the code directory so that I can use Netbeans on the host as my IDE. Unfortunately Netbeans does a lot of disk access and due to the poor Samba performance it makes the IDE hardly usable. How can I improve performance of the Samba share? On my desktop it isn't so bad but I don't know what the difference would be since they are similar setups (Win 7 hosts, cloned guests, SSDs, Vbox guests using SATA in AHCI mode, etc..). With Bridged networking is the performance between the host and guest limited by the physical hardware (Intel 6200 AGN on laptop)? I switched to Host-only and it didn't seem to improve performance at all. To clarify bad performance, I used 7zip to zip a project directory and got 19kbs to 500kbs depending on the size of the files being zipped. On my desktop it was in the ~10mbs range. Any tips for VirtualBox/Samba configuration to get improve the performance? I am using Samba 3.3.2. Hopefully Samba with SMB2 support will be released soon..

    Read the article

  • Gigabyte H55N-USB3: No video on HDMI

    - by newt
    I built a new PC with a Gigabyte H55N-USB3 / Intel Core i5 650. With a monitor plugged in the DVI port, everything works fine. I installed Windows 7 32-bit and enabled remote desktop connection. After that, I unplugged the monitor, plugged it into network and installed everything else (drivers, programs, etc) via RDP. However, when I try to use the HDMI port on my TV nothing appears. Neither during the boot, neither after Windows starts. The TV says there's "no signal" (if I remove the cable the message changes to "check cable"). The cable is new, and it is working fine with my home theater on same TV (by the way, it is the cable which came bundled with the home theater). Video driver is the latest from Intel site. Anyway, this shouldn't be the problem since there is no image during the boot. Any ideas or tips would be welcome. I'm googling around but found nothing useful, yet.

    Read the article

  • Need advice in setting up server. fastCGI, suExec, speed, security, etc.

    - by lewisqic
    I am running my own dedicated server with centOS 5 and WHM/cPanel. I would like to configure my server to meet my needs but I need a little help. It will only be my own websites being run on this server. I'm still a little green when it comes to server administration so please forgive my ignorance. What I Would Like to Have: I need some public directories to be writable (for user image uploads and things like that) but I don't want those directories to have 777 permissions. I need individual accounts to have the ability to set custom php settings for their own account without affecting other accounts, whether through a php.ini file or through .htaccess or any other method. I would like things to run as fast as possible, whether that means using a php optimizer or cacher, such as eaccelerator or xcache or anything else. I need things to be as secure as possible. Here Are My Questions What should I use for my php handler? DSO? CGI? fastCGI? suPHP? Other? Should I be using suEXEC? What are the benefits or downfalls of this? What php optimizer/cacher is best to use? Are there any other security tips I need to know about all of this? I'd appreciate any advice or direction that can be offered. Thanks!

    Read the article

  • Could I use Windows 7 instead of Windows SBS 2008 for this server?

    - by Ecyrb
    First off, I'm not a sys admin. I'm just a software developer trying to help out my parents' small business. Right now they have one server, a domain controller with a P4 processor running SBS 2003. They also have this machine hosting QuickBooks, MySQL for the old version of an app, and SQL Server 2008 Express for the new version of the app (which will replace the old eventually). They've been complaining about the workstations being slow so I figured it might help if they bought a new server and moved QuickBooks, MySQL, and SQL Server to the new server, leaving the old server as just a DC. In trying to pick an operating system for their new server, I was thinking about Windows SBS 2008 Standard with enough licenses for seven machines. But that's a lot more money than they're going to want to spend. So then I wondered if there's any real advantage to having a server OS as opposed to just throwing Windows 7 on the new server. It's a lot cheaper and I can't think of any SBS features that it would need if it's just hosting QuickBooks, MySQL, and SQL Server. Would it be okay to use Windows 7 for a server like this? Are there any advantages to using SBS 2008 that I would be missing out on? Any additional tips are much appreciated!

    Read the article

  • How to play individual albums in iTunes?

    - by Herb Caudill
    I know of two ways to play one specific album in iTunes: Do a search that's specific enough to include just that album and no other tracks; press a "Play album" button. (Doesn't work in cover flow or list view.) Go to list view; turn on column browser; in View/Column Browser, make sure "Albums" is showing; double-click an album name. These are fine as far as they go, but: Double-clicking an album in cover flow will play the album, and then keep going (in alphabetical order). That's no good. In playlists like "Purchased" or "Recently Added", you can either view and play whole albums, or sort by date added; you can't do both. In general, there's no straightforward way to get from a track in a playlist to the whole album it belongs to. What I would really, really like, would be to right-click on any song or album cover, anywhere, and choose "Play album". While I'm waiting for Apple to add that, any tips for simple album-centric listening?

    Read the article

  • System With Two Network Adapters

    - by Synetech inc.
    Hi, My system has a NIC (Marvell Yukon) built-into the motherboard, but I also have a D-Link (RealTek) card. I figure that using the D-Link and disabling the Marvell makes the most sense, though I'm wondering if maybe the built-in one has better throughput (not that my Internet connection is so fast). Also, I'm wondering about the merits of using both at the same time. My router has four ports and I have experimented with enabling and plugging both NICs into the router. I was able to connect to the Internet, but the pattern of usage seemed irregular (which adapter was chosen for the transfer and any given point). I also considered bridging the two, but am having difficulty in finding out what exactly creating network bridge does in the context of the Windows Network Connections window. I am familiar with the concept of connecting networks, so it seems to me that birding two connections on the same segment is pointless at best (and can cause problems like loops?) Does anyone have any tips on what to do if a system has more than one NIC and any clarification on the bridge option? Thanks a lot.

    Read the article

  • 100% CPU when doing 4 or more concurrent requests with Magento

    - by pancake
    Currently I'm having trouble with a server running Magento, it's unbelievably slow. It's a VPS with a few Magento installations on it used for development, so I'm the only one using them. When I do 4 request all 2 seconds after each other I'm finished in 10 seconds. Slow, but still within the limits of my patience. When I do 4 "concurrent" requests, however (opening 4 tabs in a row, very quickly) all four cores go to 100% and stay there for like a minute. How is this possible? I know that there are a lot of possibilities here, so any tips on how to make an Apache/PHP server go faster are also welcome. It used to go a lot faster before, and I've also tried APC, but it kept causing problems (PHP errors, something with memory pools) so I've disabled it. By the way, the Magento cache is off and compiling is also off. I know this makes Magento slower than usual, but I don't think a 60 second response time is normal for any Magento installation. Virtual hardware: 4 Cores and 4096MB RAM Swap is never used (checked with htop) 100GB disk space, of which 10% is in use Software: Debian 6 DirectAdmin and apache custombuild PHP 5.2.17 (CLI) If you need more info, please tell me how to get it, because I probably don't know how. I do know how to use the command line in linux and the usage of quite a few commands, but my experience with managing a server is limited.

    Read the article

  • Fresh install CentOS 6.4 64b with directadmin slowly consumes all memory and crashes

    - by Coen Ponsen
    Dear server fault community, This is my first question on server fault, i'm new to server (mis)configuration so please forgive me for asking something stupid :) I'm running Directadmin on a CentOS 6.4 64b with 4GB memory and over 10000Gh virtual machine. I migrated my websites because my former vps couldn't keep up anymore. Only half of the websites from this 1GB machine were migrated jet. So the migration is still in progress and already my server crashes every day. The server performance up until that moment is perfect. The directadmin log files show nothing out of the ordinary. Yesterday only the mysql server crashed but it also crashed the entire machine before. The memory usage in DA seems to be normal: directadmin directadmin (pid 3923 22158 22159 22160 22161 22162 )8.75 MB dovecot dovecot (pid 3851 ) 47.8 MB exim exim (pid 1350 ) 1.29 MB httpd (pid 21525 21528 21529 21530 21531 21532 21546 21571 21742 21743 21744 )490.4 MB mysqld mysqld (pid 1299 ) 287.8 MB named named (pid 3807 ) 16.3 MB proftpd proftpd (pid 1481 ) 1.91 MB sshd sshd (pid 1173 21494 ) 5.16 MB Restarting services immediately frees up memory, but slowly over time the memory usage increases(about 24 hours to crash). The commands: # sync # echo 3 > /proc/sys/vm/drop_caches Will free al memory correct. I could just create a cronjob but it seems the wrong way around to me. I can't seem to pinpoint the cause. Any advices, references or tips are highly appreciated! Greetings, Coen edit: free -m : after drop_caches: total used free shared buffers cached Mem: 3830 735 3095 0 0 21 -/+ buffers/cache: 712 3117 Swap: 991 0 991 I'll post another one this evening.

    Read the article

  • MS Word custom dictionary making spellcheck slow - ideas?

    - by ezuk
    I have a user who edits technical materials. She uses MS Word's Custom Dictionary all the time for spelling; it has grown very large, and is now making spell check very slow. All of the advice I've read online says to disable the custom dictionary. This is an easy solution, but is not workable for the user, because she actually needs this dictionary. So, is there any way to optimize the custom dictionary and/or Word itself, so that a large dictionary file doesn't slow things down quite so badly? Many thanks. Update after suggestions: I ran contig on the file, and it reports just 1 frag, so that's not the issue I think. The file is 9.95KB -- 1,117 lines, each consisting of just a single word. I viewed the file using Notepad and none of the lines seems corrupted, strange, or overly long (no line seems to be over 10 chars or so). Both of your suggestions were helpful so I will upvote both; any further tips would be most welcome.

    Read the article

  • Random "not accessible" "you might not have permission to use this network resource"

    - by Jim Fred
    A couple of computers, both Win7-64 can connect to shares on a NAS server, at least most of the time. At random intervals, these Win7-64 computers cannot access some shares but can access others on the same NAS. When access is denied, a dialog box appears saying "\\myServer\MyShare02 not accessible...you might not have permission to use this network resource..." Other shares, say \\myServer\MyShare01, ARE accessible from the affected computers and yet other computers CAN access the affected shares. Reboots of the affected computers seem to allow the affected computer to connect to the affected shares - but then, getting a cup of coffee seems to help too. When the problem appears, the network seems to be ok e.g. the affected computers can access other shares on the affected server and can ping etc. Also Other computers can access the affected shares. The NAS server is a NetGear ReadyNas Pro. The problem might be on the NAS side such as a resource limitation but since only 2 Win7-64 PCs seem to be affected the most, the problem could be on the PC side - I'm not sure yet. I of course searched for solutions and found several tips addressing initial connection problems (use correct workgroup name, use IP address instead of server name, remove security restrictions etc) but none of those remedies address the random nature of this problem.

    Read the article

  • How to choose the right PHP Framework for web development?

    - by liliwang
    Hi! I'm a PHP Pro, but haven't use any PHP framework till now, so I have no clue on how to choose a PHP framework. Do you have some tips to help me choose the/a right PHP Framework? I want a stable and secure PHP framework for Projects with about 400 hours development time. It should be possible to use the framework on Shared-Hosting-Webservers. I don't need some AJAX support (I'm using extJS). It would be nice if the framework supports Rapid Application Development and object-relational mapping. Also some of the standard-functions (Authentification, form validation) would be nice. Caching would be a useful, but isn't needed. Needs for a PHP framework: Shared-Hosting-Webserver-Support for Projects between 200 und 400 hours work Developing Modell "Rapid Application Development" supported object-relational mapping supported If possible: Caching Already finished Modules (e.g. Authentification, form validation, ..) Easy to learn Which PHP framework is the right one I am seeking for?

    Read the article

  • What can inexperienced admin expect after server setup completed seemingly fine? [closed]

    - by Miloshio
    Inexperienced person seems to have done everything fine so far. This is his very first time that he is the only one in charge for LAMP server. He has installed OS, network, Apache, PHP, MySQL, Proftpd, MTA & MDA software, configured VirtualHosts properly (facts because he calls himself admin), done user management and various configuration settings with respect to security recommendations and... everything is fine for now... For now. If you were directing horror movie for server admin above mentioned what would you make up for boogieman that showed up and started to pursue him? Omitting hardware disaster cases for which one cannot do anything 'from remote', what is the most common causes of server or part-of-server or server-related significant failure when managed by inexperienced admin? I have in mind something that is newbie admins very often missing which is leading to later intervention of someone with experience? May that be some uncontrolled CPU-eating leftover process, memory-related glitch, widely-used feature that messes up something unexpected on anything like that? Newbie admin for now only monitors disk-space and RAM usage, and number of running processes. He would appreciate any tips regarding what's probably going to happen to his server over time.

    Read the article

  • MacBook Pro (2007 - ATI-Card) Screen goes half black then shuts down the entire computer

    - by BluePerry
    Hey, when I'm starting my MBP I get about 10-60 seconds of the booting process before the screen goes half black (Its like applying a black to transparent gradient from the left side of the screen to the middle of the screen). After a 5 seconds the entire screen blacks out and the MBP shuts down. There have been issues with heat and some minor artifacts on the screen in the past but nothing serious as far as I know. Everything could be resolved by rebooting or letting the MBP cool down a bit. I would like to identify the problem now. There are 3 possibilities I can think of right now: My graphics card is defect and shuts down after a few seconds. (But if thats true, I find it kind of hard to explain the HALF black screen) My LCD-Panel is defect and sends back wrong signals so the system shuts down??? (I not sure about that) My fan or/and thermal sensors are defect and forcing the graphics card to shut down. Can anyone point if I'm right or if there yet another reason for this. I'd be thankful for any hint or tips. Cheers, Per

    Read the article

  • Best way to create and restore a Drive Image with Windows 7? [closed]

    - by jasondavis
    Possible Duplicate: Want to create a system image I am about to build a new PC. I am a windows 7 user. For years now I have been wanting to install windows and all my favorite software, music, etc., and then make a drive IMAGE and be able to go in 6 months later or WHENEVER I want to start fresh and completely format my drives and restore my IMAGE and have all my settings, programs, etc be just5 like when I created the original image. I know there is many ways to do this but I have never done this 100% successfully and I have about a week to figure out how to do it perfectly for when I build my new PC. I have heard good things about using tried Acronis true image in the PAST for doing what I describe4, I tried using it but, but the newer versions are overly complex and don't even seem to work the way I hoped. I also see that Windows 7 has some sort of drive IMAGE creator itself as well. Does the newer Windows 7 image creator do what I am describing above? If it does do what I am asking for (complete drive image with windows, all programs and settings) saved to an IMAGE file that can easily be restored to ANY hard drive in the future? Please share your experiences, tips, ideas on how to achieve this the easiest and most reliable way please

    Read the article

  • System With Two Network Adapters [closed]

    - by Synetech inc.
    Hi, My system has a NIC (Marvell Yukon) built-into the motherboard, but I also have a D-Link (RealTek) card. I figure that using the D-Link and disabling the Marvell makes the most sense, though I'm wondering if maybe the built-in one has better throughput (not that my Internet connection is so fast). Also, I'm wondering about the merits of using both at the same time. My router has four ports and I have experimented with enabling and plugging both NICs into the router. I was able to connect to the Internet, but the pattern of usage seemed irregular (which adapter was chosen for the transfer and any given point). I also considered bridging the two, but am having difficulty in finding out what exactly creating network bridge does in the context of the Windows Network Connections window. I am familiar with the concept of connecting networks, so it seems to me that birding two connections on the same segment is pointless at best (and can cause problems like loops?) Does anyone have any tips on what to do if a system has more than one NIC and any clarification on the bridge option? Thanks a lot.

    Read the article

  • does leaving the laptop cord in break the cord?

    - by firedrake
    i recently got a new cord for my laptop because the cord i had before broke.im not sure how it got messed up, but one moment it charged my laptop and the next moment it didn't. i then got a new cord. the new cord worked perfectly fine until now, and it has only been a month. the cord wont work unless i am pressing it into the socket, which i am currently doing. the only thing i can find in common with the cords is that i leave them plugged in 24/7. my brother says that is the problem, but i do not think it is.any tips or hints? im going to use duct tape to keep the pressure on the cord till i can find a better solution(im also thinking it could be the hole i plug it into on the back of my computer, but im focusing on the other idea for now.if i wiggle the plug part in the socket of my computer it will stop charging unless im pressing it in or to the side) any help or ideas are appreciated. not sure if this will help but i use a gateway with windows vista. thanks

    Read the article

  • How to know who accessed a file or if a file has 'access' monitor in linux

    - by J L
    I'm a noob and have some questions about viewing who accessed a file. I found there are ways to see if a file was accessed (not modified/changed) through audit subsystem and inotify. However, from what I have read online, according to here: http://www.cyberciti.biz/tips/linux-audit-files-to-see-who-made-changes-to-a-file.html it says to 'watch/monitor' file, I have to set a watch by using command like: # auditctl -w /etc/passwd -p war -k password-file So if I create a new file or directory, do I have to use audit/inotify command to 'set' watch first to 'watch' who accessed the new file? Also is there a way to know if a directory is being 'watched' through audit subsystem or inotify? How/where can I check the log of a file? edit: from further googling, I found this page saying: http://www.kernel.org/doc/man-pages/online/pages/man7/inotify.7.html The inotify API provides no information about the user or process that triggered the inotify event. So I guess this means that I cant figure out which user accessed a file? Only audit subsystem can be used to figure out who accessed a file?

    Read the article

  • Can you help me understand my SATA/RAID options?

    - by andrz_001
    I've a gigabyte GA-M720-US3 motherboard. Recently, I noticed the following during boot: IDE channel 0 Master (none) IDE channel 0 Slave (none) IDE channel 2 Master (my hdd) IDE channel 2 Slave (my dvd drive) IDE channel 3 Master (none) IDE channel 3 Slave (none) Of course, the same information is contained in the BIOS/CMOS. The HDD is connected to the mobo via a SATA(2?) cable at the port(?) labeled SATA2_0. The DVD drive is connected by a similar cable at SATA2_1. Why doesn't the information displayed during the boot and in BIOS reflect how I plugged the cables in? I mean, why "none" for channel 0 when there is something in SATA2_0. (or is that serious naivete on my part!?) Where's Channel 1 master and slave? Since these are SATA cables and not the IDE ribbons from a time ago, why the whole master/slave declaration during boot and in BIOS? Should my BIOS reflect the fact that these are SATA cables? I mean, in BIOS, should the "Onchip SATA mode IDE" be set to RAID or AHCI instead of IDE? Any replies, answers, suggestions, links, tips will be much appreciated. Thank you in advance!

    Read the article

  • Java constructor using generic types

    - by user37903
    I'm having a hard time wrapping my head around Java generic types. Here's a simple piece of code that in my mind should work, but I'm obviously doing something wrong. Eclipse reports this error in BreweryList.java: The method initBreweryFromObject() is undefined for the type <T> The idea is to fill a Vector with instances of objects that are a subclass of the Brewery class, so the invocation would be something like: BreweryList breweryList = new BreweryList(BrewerySubClass.class, list); BreweryList.java package com.beerme.test; import java.util.Vector; public class BreweryList<T extends Brewery> extends Vector<T> { public BreweryList(Class<T> c, Object[] j) { super(); for (int i = 0; i < j.length; i++) { T item = c.newInstance(); // initBreweryFromObject() is an instance method // of Brewery, of which <T> is a subclass (right?) c.initBreweryFromObject(); // "The method initBreweryFromObject() is undefined // for the type <T>" } } } Brewery.java package com.beerme.test; public class Brewery { public Brewery() { super(); } protected void breweryMethod() { } } BrewerySubClass.java package com.beerme.test; public class BrewerySubClass extends Brewery { public BrewerySubClass() { super(); } public void androidMethod() { } } I'm sure this is a complete-generics-noob question, but I'm stuck. Thanks for any tips!

    Read the article

  • Why does my ftp(e)s server fails like half of the time

    - by user1092608
    I have this discussion at work regarding our ftp server running via vsftpd. Initially, we have opted to serve ftpes instead of sftp because this seemed the most flexible and straightforward solution for our server to have secure file transmission. Afterwards, our ftp server seems to be a source of issues for our end users. Half of the time, users complain about not working ftp connections. I must say, i tested our FTP trough different infrastructures (=in the field, at random times at random places) and indeed, sometimes behind some configurations (=no idea how they are configured, because the 'field' testing), i recieve errors. Some of the are: Error: Failed to retrieve directory listing (filezilla) Furthermore, behind my basic home configuration, everything seems to be running fine. I (think I) did all the basic configuration checks (passive mode?, firewall for all ports?, ...) and can't seem to find the source. Being a bunch of techies at our small office, yet knowing nothing about infrastructure, some start suggesting that ftps protocol could be the source of issues. ("No, i only knew sftp so far" "Ftps is not widespread"). I, however, strongly doubt this hypothesis, since reading around on the www, asking questions on serverfault, everyone seems to deny this. So, as I would like to avoid reconfiguring, since this involves messing around in our SSH service, our virtual user setup and ftp service, i would need some advice on 1) what could be potentially the general cause? 2) do you have some general tips? 3) would you mind having a look at my configuration file? ----- General Settings ----- write_enable=YES dirmessage_enable=YES nopriv_user=ftpsecure ftpd_banner="Welcome to XXXX FTP!" hide_ids=YES hide_file=.* max_per_ip=10 max_clients=10 local_enable=YES local_umask=022 chroot_local_user=YES secure_chroot_dir=/usr/share/empty userlist_enable=NO userlist_deny=YES userlist_file=/etc/vsftp_deny_users guest_enable=YES guest_username=ftpvirtual virtual_use_local_privs=YES user_sub_token=$USER local_root=/srv/ftp/ftpvirtual/$USER anonymous_enable=NO syslog_enable=NO xferlog_enable=YES xferlog_file=/var/log/vsftpd_xfer.log connect_from_port_20=YES pam_service_name=vsftpd listen=YES listen_port=21 pasv_enable=YES pasv_min_port=30000 pasv_max_port=30030 pasv_address=foo ssl_enable=YES rsa_cert_file=/etc/vsftpd.pem rsa_private_key_file=/etc/vsftpd.pem force_local_data_ssl=YES force_local_logins_ssl=YES ssl_tlsv1=YES ssl_sslv2=YES ssl_sslv3=YES ssl_ciphers=HIGH anon_mkdir_write_enable=NO anon_root=/srv/ftp anon_upload_enable=NO idle_session_timeout=900 log_ftp_protocol=NO dsa_cert_file=/etc/vsftpd.pem Thanks

    Read the article

  • Windows xp blinking under score after bios

    - by heyjoe
    so this is for an older pc I have to repair for a friend. The pc has an hdd of about 60 something gb, It uses win xp and let's say 60-70% of the boots it hangs on showing only an underscore bilking line after bios screen, rest of the times it boots fine or the computer shuts down on xp loading screen. Sometimes if you let it alone while the underscore is blinking, it will boot after a while, like a few minutes, some times it won't boot at all even if you give him more time, like one hour. When it boots successfully the pc seems to work fine. I think it's a bad hard disk and i'm about to suggest buying a new one and switching it but I don't have enough experience and i would hate making him buy a new hdd and not solving the problem. anyone has any tips? I know there are other topics about blinking underscores or cursors while xp is booting but the issues about the pc shutting itself down or sometimes booting really freaks me out. Can't format everything and re install until about 10 days from now, cause the dude has some program for his business on this pc and I have to migrate it when the next computer arrives, however he needs to use it until then. so please advise, thx.

    Read the article

  • Mail Server using Postfix

    - by unknown (google)
    I have currently set up my web application on Amazon EC2 server. As a well known fact sending email from EC2 has a problem. As a cheap and long lasting solution instead of using "authsmtp" is it possible to rent a server and use it as a Mail Server? I am currently looking for cheap hosting which will give me root access so that it can be configured and used as a relayhost. I am curently using Postfix as MTA. Has any one implemented this before? I am curious about its feasibility of this solution. I guess common requirements are: 1: Dedicated IP which is not black listed. 2: Open relay( open to my Server only) Any Tips for Header configurations to keep the mails out of spam folder. This is like exactly cloning authsmtp for personal use. Any suggestions for other Mail Server software instead of Postfix? Another problem is Reverse DNS for this server. Should PTR entry be present if a server is used as a relayhost?

    Read the article

  • Network Sniffing and Hubs

    - by Chris_K
    This will likely seem naive to the experts... but it has been on my mind lately. For years I've been using ntop and a cheap 4 port hub to sniff client networks to determine who's doing what -- and how much. Great way to see what's going on when they call and say "Geeze, the network seems really slow today." No need to bring in a managed switch (or access the existing one) and no need to configure spanning or mirroring. I just drop in the hub inline where I want to measure. Lately I noticed it is just about impossible to buy a real honest-to-goodness hub anymore. While looking for a new one, I had someone tell me that I should be sure to get a full-duplex hub or I'd only be seeing half the traffic when I monitor. Really? I've been using a crusty old Netgear DS104 all this time. No clue if it is half or FD. Have I really been understating my measurements? I'm just not bright enough about the physical layer to really know... Side note: Just ordered a Dualcomm Ethernet Switch TAP as a hub replacement. Seems like a nifty gadget. Any notes or tips about it would be welcome in the comments :-)

    Read the article

  • Linux 2.6.24-gentoo-r3-comtrance on x86_64 high Useage for unknown reasons

    - by Dorjan
    Hello everyone, I'm a complete rookie when it comes to all things Linux related so please treat me as such and assume I know nothing. That being said my Top says this: top - 12:08:03 up 11 days, 15:36, 0 users, load average: 5.47, 5.53, 5.46 Tasks: 296 total, 2 running, 294 sleeping, 0 stopped, 0 zombie Cpu(s): 6.3%us, 1.4%sy, 0.0%ni, 71.3%id, 20.6%wa, 0.0%hi, 0.3%si, 0.0%st Mem: 8176880k total, 8118236k used, 58644k free, 89312k buffers Swap: 1004052k total, 0k used, 1004052k free, 7235652k cached PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND 1229 root 15 -5 0 0 0 D 1 0.0 199:28.63 kjournald 2946 root 20 0 1716 676 552 D 1 0.0 145:02.94 syslogd 14553 root 20 0 2644 1268 876 R 1 0.0 0:00.34 top 14609 postfix 20 0 7896 1884 1460 D 1 0.0 0:00.02 bounce 14630 postfix 20 0 7896 1876 1452 R 0 0.0 0:00.00 bounce And my hard drives says: > df -k Filesystem 1K-blocks Used Available Use% Mounted on /dev/sda3 4925556 4474836 200508 96% / /dev/sda5 489992 36090 428602 8% /tmp /dev/sda6 377951852 236171160 122581816 66% /var none 4088440 0 4088440 0% /dev/shm It has been like it for a few days now... I know not what is causing the high server load (Normally around 1.3) can anyone give any tips on how to track down the culprit? Many thanks,

    Read the article

  • 4GB Memory Upgrade for Acer Aspire 5102WLMi

    - by Richard Slater
    I have bought a 4GB memory upgrade (2x 2GB PC2-5300 SODIMM) for my Acer Aspire 5102WLMi (Aspire 5100 Series) laptop, I installed the two memory modules correctly however with 4GB installed the laptop refuses to POST. I have tried the following: Tried both 2GB SODIMMs without the other (Worked Fine) Tried the original 512MB SODIMMs (Worked Fine) Tried with original 512MB SODIMM and new 2GB SODIMM (Worked Fine) Tried swapping over the 2GB SODIMs (Didn't Boot) Left the computer for 10 minutes with both 2GB SODIMMs installed (Didn't Boot) Checked latest BIOS installed (No Change) The Crucial website said that the laptop supported 4GB of RAM as do several other sites through found through Google, up until now I was fairly confident this would work. Couple of questions that would be good to have answered: Question: Has anyone got an Acer Aspire 5100 Series running with 4GB RAM? Answer: Yes, I have now got one working with 3.75GB Usable, the rest is occupied utilized by the Graphics Card. Question: Any tips on getting this to work; is there a CMOS reset switch? Answer: Yes there is, if both SODIMMs are removed two very small interlocking PCB tracks are revealed. If these are shorted together with a screwdriver the BIOS will be reset. Thanks.

    Read the article

< Previous Page | 208 209 210 211 212 213 214 215 216 217 218 219  | Next Page >