Search Results

Search found 21466 results on 859 pages for 'current buffer'.

Page 213/859 | < Previous Page | 209 210 211 212 213 214 215 216 217 218 219 220  | Next Page >

• Proliant server will not accept new hard disks in RAID 1+0?

  - by Leigh

  I have a HP ProLiant DL380 G5, I have two logical drives configured with RAID. I have one logical drive RAID 1+0 with two 72 gb 10k sas 1 port spare no 376597-001. I had one hard disk fail and ordered a replacement. The configuration utility showed error and would not rebuild the RAID. I presumed a hard disk fault and ordered a replacement again. In the mean time I put the original failed disk back in the server and this started rebuilding. Currently shows ok status however in the log I can see hardware errors. The new disk has come and I again have the same problem of not accepting the hard disk. I have updated the P400 controller with the latest firmware 7.24 , but still no luck. The only difference I can see is the original drive has firmware 0103 (same as the RAID drive) and the new one has HPD2. Any advice would be appreciated. Thanks in advance Logs from server ctrl all show config Smart Array P400 in Slot 1 (sn: PAFGK0P9VWO0UQ) array A (SAS, Unused Space: 0 MB) logicaldrive 1 (68.5 GB, RAID 1, Interim Recovery Mode) physicaldrive 2I:1:1 (port 2I:box 1:bay 1, SAS, 73.5 GB, OK) physicaldrive 2I:1:2 (port 2I:box 1:bay 2, SAS, 72 GB, Failed array B (SAS, Unused Space: 0 MB) logicaldrive 2 (558.7 GB, RAID 5, OK) physicaldrive 1I:1:5 (port 1I:box 1:bay 5, SAS, 300 GB, OK) physicaldrive 2I:1:3 (port 2I:box 1:bay 3, SAS, 300 GB, OK) physicaldrive 2I:1:4 (port 2I:box 1:bay 4, SAS, 300 GB, OK) ctrl all show config detail Smart Array P400 in Slot 1 Bus Interface: PCI Slot: 1 Serial Number: PAFGK0P9VWO0UQ Cache Serial Number: PA82C0J9VWL8I7 RAID 6 (ADG) Status: Disabled Controller Status: OK Hardware Revision: E Firmware Version: 7.24 Rebuild Priority: Medium Expand Priority: Medium Surface Scan Delay: 15 secs Surface Scan Mode: Idle Wait for Cache Room: Disabled Surface Analysis Inconsistency Notification: Disabled Post Prompt Timeout: 0 secs Cache Board Present: True Cache Status: OK Cache Status Details: A cache error was detected. Run more information. Cache Ratio: 100% Read / 0% Write Drive Write Cache: Disabled Total Cache Size: 256 MB Total Cache Memory Available: 208 MB No-Battery Write Cache: Disabled Battery/Capacitor Count: 0 SATA NCQ Supported: True Array: A Interface Type: SAS Unused Space: 0 MB Status: Failed Physical Drive Array Type: Data One of the drives on this array have failed or has Logical Drive: 1 Size: 68.5 GB Fault Tolerance: RAID 1 Heads: 255 Sectors Per Track: 32 Cylinders: 17594 Strip Size: 128 KB Full Stripe Size: 128 KB Status: Interim Recovery Mode Caching: Enabled Unique Identifier: 600508B10010503956574F305551 Disk Name: \\.\PhysicalDrive0 Mount Points: C:\ 68.5 GB Logical Drive Label: A0100539PAFGK0P9VWO0UQ0E93 Mirror Group 0: physicaldrive 2I:1:2 (port 2I:box 1:bay 2, S Mirror Group 1: physicaldrive 2I:1:1 (port 2I:box 1:bay 1, S Drive Type: Data physicaldrive 2I:1:1 Port: 2I Box: 1 Bay: 1 Status: OK Drive Type: Data Drive Interface Type: SAS Size: 73.5 GB Rotational Speed: 10000 Firmware Revision: 0103 Serial Number: B379P8C006RK Model: HP DG072A9B7 PHY Count: 2 PHY Transfer Rate: Unknown, Unknown physicaldrive 2I:1:2 Port: 2I Box: 1 Bay: 2 Status: Failed Drive Type: Data Drive Interface Type: SAS Size: 72 GB Rotational Speed: 15000 Firmware Revision: HPD9 Serial Number: D5A1PCA04SL01244 Model: HP EH0072FARUA PHY Count: 2 PHY Transfer Rate: Unknown, Unknown Array: B Interface Type: SAS Unused Space: 0 MB Status: OK Array Type: Data Logical Drive: 2 Size: 558.7 GB Fault Tolerance: RAID 5 Heads: 255 Sectors Per Track: 32 Cylinders: 65535 Strip Size: 64 KB Full Stripe Size: 128 KB Status: OK Caching: Enabled Parity Initialization Status: Initialization Co Unique Identifier: 600508B10010503956574F305551 Disk Name: \\.\PhysicalDrive1 Mount Points: E:\ 558.7 GB Logical Drive Label: AF14FD12PAFGK0P9VWO0UQD007 Drive Type: Data physicaldrive 1I:1:5 Port: 1I Box: 1 Bay: 5 Status: OK Drive Type: Data Drive Interface Type: SAS Size: 300 GB Rotational Speed: 10000 Firmware Revision: HPD4 Serial Number: 3SE07QH300009923X1X3 Model: HP DG0300BALVP Current Temperature (C): 32 Maximum Temperature (C): 45 PHY Count: 2 PHY Transfer Rate: Unknown, Unknown physicaldrive 2I:1:3 Port: 2I Box: 1 Bay: 3 Status: OK Drive Type: Data Drive Interface Type: SAS Size: 300 GB Rotational Speed: 10000 Firmware Revision: HPD4 Serial Number: 3SE0AHVH00009924P8F3 Model: HP DG0300BALVP Current Temperature (C): 34 Maximum Temperature (C): 47 PHY Count: 2 PHY Transfer Rate: Unknown, Unknown physicaldrive 2I:1:4 Port: 2I Box: 1 Bay: 4 Status: OK Drive Type: Data Drive Interface Type: SAS Size: 300 GB Rotational Speed: 10000 Firmware Revision: HPD4 Serial Number: 3SE08NAK00009924KWD6 Model: HP DG0300BALVP Current Temperature (C): 35 Maximum Temperature (C): 47 PHY Count: 2 PHY Transfer Rate: Unknown, Unknown

  Read the article

• My computer freezes irregurarly

  - by Manhim

  My computer started to freeze at irregular times for 3 weeks now. What happens My computer freezes, the video stops. (No graphic glitches, it just stops) Sound keeps playing up to some time (Usually 10-30 seconds) then stops playing. Sometimes, randomly, the screen on my G-15 keyboard flickers and I see caracters not at the right places. Usually happens for about 1-2 seconds and a bit before my computer freezes. I have to keep the power button pressed for 4 seconds to shut my computer down. I still hear my hard drives and fans working. Sometimes it works with no problems for a full day, some other times it just keeps freezing each time I restart my computer and I have to leave it for the rest of the day. Sometimes my mouse freezes for a fraction of a second (Like 0.01 to 0.2 seconds) quite randomly, usually before it freezes. No errors spotted by the "Action center" unlike when I had problems with my last video card on this system (Driver errors). My G-15 LCD screen also freezes. What I did so far I have had similar problems in the past and I had changed my hard drive (It was faulty), so I tested my software RAID-0 array and it was faulty so I changed it. (I reinstalled Windows 7 with this part). I also tested with unplugging my secondary hard drive. My CPU was running at about 100 degree Celsius, I removed the dust between the fans and the heatsink and it's now between 50-60. I ran a CPU stress-test and it didn't freeze during the tests (using Prime95 on all cores) Ran a memory test (using memtest86+) for a single pass and there were no errors. Ran a GPU stress test with ati-tools and furmark and it didn't freeze during the tests. (No artefacts either) I had troubles with my graphic card when I got it, but I think that it got fixed with a driver update. I checked the voltages in my BIOS setup and they all seemed ok (±0.2 I think). I have ran on the computer without problems with Fedora 15 on an external hard drive (Appart that it couldn't load Gnome 3 and was reverting to Gnome 2, didn't want to install drivers since I use it on multiple computers) I used it to backup my files from the raid array to my 1TB hard drive for the reinstallation of Windows. (So the crashes only happenned on Windows) [The external hard drive is plugged directly on a SATA port] I contacted EVGA (My graphic card vendor) and pointed them on this question, I'm looking for an answer. Ran sensors on Fedora 15 and got this output: http://pastebin.com/0BHJnAvu When it happens When I play video games (Mostly) When I play flash games (Second most) When I'm looking at my desktop background (It rarely happens when I have a window open, but it does, sometimes) Specs Windows Seven x64 Home Premium Motherboard: M2N-SLI Deluxe CPU: AMD Phenom 9950 x2 @ 2.6GHz Memory: Kingston 4x2GB Dual Channel (Pretty basic memory sticks) Hard drives: Was 2x250GB (Western digital caviar) in raid-0 + 1TB (WD caviar black), I replaced the raid array with a 750GB (WD caviar black) [Yes I removed the array from the raid configurations] 750W Power supply No overcloking. Ever. There have been some power-downs like 4-5 weeks ago, but the problem didn't start immediately after. (I wasn't home, so my computer got shut-down) My current to-try list Change the thermal paste on my CPU. Change my graphic card with a temporary one and stress the computer. Change my power supply. In this situation, how can I successfully pin-point the current hardware problem? (If it's a hardware problem) Because I don't really have the budget to just forget and replace everything. I also don't really have hardware to test-replace current hardware.

  Read the article

• Vim: Context sensitive code completion for PHP

  - by eddy147

  Vim gives me too much options when I use code completion. In a class, and type $class- it gives me about a zillion options, so not only from the class itself but also from php, all globals ever created, in short: a mess. I only want to have the options from the class itself (or the parent subtype class it extends from), so context or scope sensitive code completion, just like Netbeans for example. How can I do that? My current configuration is this: I am using ctags, and created 1 ctags file for our (big) application in the root. This is the .ctags file I used to create the ctags file: -R -h ".php" --exclude=.svn --languages=+PHP,-JavaScript --tag-relative=yes --regex-PHP=/abstract\s+class\s+([^ ]+)/\1/c/ --regex-PHP=/interface\s+([^ ]+)/\1/c/ --regex-PHP=/(public\s+|static\s+|protected\s+|private\s+)\$([^ \t=]+)/\2/p/ --regex-PHP=/const\s+([^ \t=]+)/\1/d/ --regex-PHP=/final\s+(public\s+|static\s+|abstract\s+|protected\s+|private\s+)function\s+\&?\s*([^ (]+)/\2/f/ --PHP-kinds=+cdf --fields=+iaS This is the .vimrc file: " autocomplete funcs and identifiers for languages autocmd FileType php set omnifunc=phpcomplete#CompletePHP autocmd FileType python set omnifunc=pythoncomplete#Complete autocmd FileType javascript set omnifunc=javascriptcomplete#CompleteJS autocmd FileType html set omnifunc=htmlcomplete#CompleteTags autocmd FileType css set omnifunc=csscomplete#CompleteCSS autocmd FileType xml set omnifunc=xmlcomplete#CompleteTags autocmd FileType php set omnifunc=phpcomplete#CompletePHP autocmd FileType c set omnifunc=ccomplete#Complete " exuberant ctags " the magic is the ';' at end. it will make vim tags file search go up from current directory until it finds one. set tags=projectrootdir/tags; map <F8> :!ctags " TagList " :tag getUser => Jump to getUser method " :tn (or tnext) => go to next search result " :tp (or tprev) => to to previous search result " :ts (or tselect) => List the current tags " => Go back to last tag location " +Left click => Go to definition of a method " More info: " http://vimdoc.sourceforge.net/htmldoc/tagsrch.html (official documentation) " http://www.vim.org/tips/tip.php?tip_id=94 (a vim tip) let Tlist_Ctags_Cmd = "~/bin/ctags" let Tlist_WinWidth = 50 map <F4> :TlistToggle<cr> "see http://vim.wikia.com/wiki/Make_Vim_completion_popup_menu_work_just_like_in_an_IDE " will change the 'completeopt' option so that Vim's popup menu doesn't select the first completion item, but rather just inserts the longest common text of all matches :set completeopt=longest,menuone " will change the behavior of the <Enter> key when the popup menu is visible. In that case the Enter key will simply select the highlighted menu item, just as <C-Y> does :inoremap <expr> <CR> pumvisible() ? "\<C-y>" : "\<C-g>u\<CR>" " inoremap <expr> <C-n> pumvisible() ? '<C-n>' : \ '<C-n><C-r>=pumvisible() ? "\<lt>Down>" : ""<CR>' inoremap <expr> <M-,> pumvisible() ? '<C-n>' : \ '<C-x><C-o><C-n><C-p><C-r>=pumvisible() ? "\<lt>Down>" : ""<CR>'

  Read the article

• Why are USB 2.0 devices crashing my system?

  - by BenAlabaster

  Background on the machine I'm having a problem with: The machine was inherited and appears to be circa 2003 (there's a date stamp on the power supply which leads me to this conclusion). I've got it set up as a Skype terminal for my 2 year old to keep in touch with her grandparents and other members of the family - which everyone loves. It has a generic baby-ATX motherboard with no identifying markings. CPU-Z identifies the motherboard model as VT8601 but doesn't provide me with any manufacturer name. There's one stamp on the motherboard that says "Rev.B". On board it has 10/100 LAN, 2 x USB 1.0, VGA, PS/2 for KB and mouse, parallel port, 2 x serial ports, 2 x IDE, 1 x floppy, 2 x SDRAM slots, 1 x CPU housing that is seating a 1.3GHz Intel Celeron CPU, 3 x PCI, 1 x AGP - although you can only use 2 of the PCI slots if you use the AGP slot due to the physical layout of the board. It's got 768Mb PC133 SDRAM - 1 x 512Mb & 1 x 256Mb installed as well as a D-LINK WDA-2320 54G Wi-Fi network card and a generic USB 2.0 expansion board containing 3 x external + 1 x internal USB connectors. All this is sitting in a slimline case. I don't know the wattage of the PSU, but can post this later if this proves to be helpful. The motherboard is running a version of Award BIOS for which I don't have the version number to hand but can again post this later if it would be helpful. It has an 80Gb Western Digital hard drive freshly formatted and built with Windows XP Professional with Service Pack 3 and all current patches. In addition to Windows XP, the only other software it's running is Skype 4.1 (4.2 crashes the machine as soon as it starts up). It's got a Daytek MV150 15" touch screen running through the VGA and COM1 with the most current drivers from the Daytek website and the most current version of ELO-Touchsystems drivers for the touch component. The webcam is a Logitech Webcam C200 with the latest drivers from the Logitech website. The problem If I hook any USB 2.0 devices to this machine, it hangs the whole machine and I have to hard boot it to get it back up. Workarounds found I can plug the same devices into the on board USB 1.0 connectors and everything works fine, albeit at reduced performance. I've tried 3 different kinds of USB thumb drives, 3 different makes/models of webcams and my iPhone all with the same effect. They're recognized and don't hang the machine when I hook them to the USB 1.0 but if I hook them to the USB 2.0 ports, the machine hangs within a couple of seconds of recognizing the devices were connected. Attempted solutions I've tried disabling all the on board devices that I'm not using - such as the on board LAN, the second COM port, the AGP connector etc. through the BIOS in an (perhaps misguided or futile) attempt to reduce the power consumption... I don't think it had any effect but it didn't do any harm. I was wondering if the PSU wattage just isn't enough to drive the USB 2.0 devices; I've seen this suggested but haven't found any confirmation that this could really be an issue - nor have I found a way to work around this issue - if indeed it is one. Any ideas? The only thing I haven't done which I only just thought of while writing this essay is trying the USB 2.0 card in a different PCI slot, or re-ordering the wi-fi and USB cards in the slots... although I'm not sure if this will make any difference. I've installed the USB card in another machine and it works without issue, so it's not a problem with the USB card itself. Other thoughts Perhaps this is an incompatibility between the USB 2.0 card and the BIOS, would re-flashing the BIOS with a newer version help? Do I need to be able to identify the manufacturer of the motherboard in order to be able to find a BIOS edition specific for this motherboard or will any version of Award BIOS function in its place? Question Does anyone have any ideas that could help me get my USB 2.0 devices hooked up to this machine?

  Read the article

• Trying to prevent Windows from hibernating/sleeping automatically

  - by user328821

  My Dell XPS 8700 (Win 7) suddenly began putting itself to sleep at 6pm daily, even if I'm typing. I don't know what caused this to occur, except possibly a windows update that took place in the middle of the night. I initially went into settings for power and saw 2 plans set up, one from Dell and the other window's Power saver plan. I set both to never for sleep and hibernate yet it still occurred. I have current drivers and a fairly new UPS that has software to set to shutdown only after power loss. Dell is of little help, can anyone point me in the right direction? I did do the powerdfg -energy program and came up with this: Power Efficiency Diagnostics Report Scan Time 2014-05-08T19:21:48Z Scan Duration 60 seconds System Manufacturer Dell Inc. System Product Name XPS 8700 BIOS Date 08/23/2013 BIOS Version A04 OS Build 7601 Platform Role PlatformRoleDesktop Plugged In true Process Count 115 Thread Count 1631 Report GUID {097caf99-039b-44c3-b154-d797bfbfdfcc} Analysis Results Errors Power Policy:Sleep timeout is disabled (Plugged In) The computer is not configured to automatically sleep after a period of inactivity. System Availability Requests:System Required Request The device or driver has made a request to prevent the system from automatically entering sleep. Requesting Driver Instance HDAUDIO\FUNC_01&VEN_10EC&DEV_0899&SUBSYS_102805B7&REV_1000\4&220b1bbc&0&0001 Requesting Driver Device Realtek High Definition Audio CPU Utilization:Processor utilization is high The average processor utilization during the trace was high. The system will consume less power when the average processor utilization is very low. Review processor utilization for individual processes to determine which applications and services contribute the most to total processor utilization. Average Utilization (%) 9.48 Warnings Platform Timer Resolution:Platform Timer Resolution The default platform timer resolution is 15.6ms (15625000ns) and should be used whenever the system is idle. If the timer resolution is increased, processor power management technologies may not be effective. The timer resolution may be increased due to multimedia playback or graphical animations. Current Timer Resolution (100ns units) 10000 Maximum Timer Period (100ns units) 156001 Platform Timer Resolution:Outstanding Kernel Timer Request A kernel component or device driver has requested a timer resolution smaller than the platform maximum timer resolution. Requested Period 10000 Request Count 2 Platform Timer Resolution:Outstanding Timer Request A program or service has requested a timer resolution smaller than the platform maximum timer resolution. Requested Period 10000 Requesting Process ID 8672 Requesting Process Path \Device\HarddiskVolume3\Program Files (x86)\Mozilla Firefox\firefox.exe Platform Timer Resolution:Outstanding Timer Request A program or service has requested a timer resolution smaller than the platform maximum timer resolution. Requested Period 100000 Requesting Process ID 1212 Requesting Process Path \Device\HarddiskVolume3\Windows\System32\svchost.exe Power Policy:802.11 Radio Power Policy is Maximum Performance (Plugged In) The current power policy for 802.11-compatible wireless network adapters is not configured to use low-power modes. CPU Utilization:Individual process with significant processor utilization. This process is responsible for a significant portion of the total processor utilization recorded during the trace. Process Name audiodg.exe PID 1304 Average Utilization (%) 4.73 Module Average Module Utilization (%) \Device\HarddiskVolume3\Windows\System32\msvcrt.dll 1.88 \Device\HarddiskVolume3\Windows\System32\MaxxAudioAPO5064.dll 1.77 \Device\HarddiskVolume3\Windows\System32\AudioEng.dll 0.80 CPU Utilization:Individual process with significant processor utilization. This process is responsible for a significant portion of the total processor utilization recorded during the trace. Process Name thunderbird.exe PID 6036 Average Utilization (%) 0.35 Module Average Module Utilization (%) \Device\HarddiskVolume3\Program Files (x86)\Mozilla Thunderbird\xul.dll 0.16 \Device\HarddiskVolume3\Program Files (x86)\Mozilla Thunderbird\mozjs.dll 0.05 \SystemRoot\System32\win32k.sys 0.03 CPU Utilization:Individual process with significant processor utilization. This process is responsible for a significant portion of the total processor utilization recorded during the trace. Process Name dwm.exe PID 1340 Average Utilization (%) 0.25 Module Average Module Utilization (%) \Device\HarddiskVolume3\Windows\System32\dwmcore.dll 0.08 \Device\HarddiskVolume3\Windows\System32\nvwgf2umx.dll 0.05 \SystemRoot\system32\ntoskrnl.exe 0.03 CPU Utilization:Individual process with significant processor utilization. This process is responsible for a significant portion of the total processor utilization recorded during the trace.

  Read the article

• Print directly to CUPS server from non-local clients (Ubuntu 14.04)

  - by OEP

  I set up a CUPS server with a few queues and printing from local clients (the CUPS test page and Samba) seems to work just fine. It seems like the CUPS server is denying non-local clients though: 130.127.48.70 - - [03/Jun/2014:14:29:19 -0400] "POST /printers/m137 HTTP/1.1" 200 390 Validate-Job successful-ok 130.127.48.70 - - [03/Jun/2014:14:29:19 -0400] "POST /printers/m137 HTTP/1.1" 200 339 Create-Job client-error-not-authorized localhost - - [03/Jun/2014:14:40:50 -0400] "POST /printers/m137 HTTP/1.1" 200 410869 Print-Job successful-ok This makes me think I have some sort of host-based restriction in my configuration file, but I can't find it. I've even set my default policy to Allow all only to get the same log message. I'm working from a configuration file which had previously worked on an older version of CUPS, which looks quite similar to the example cupsd.conf. I could be wrong but it looks like that final <Limit All> block ought to allow the actions the logs complain about. MaxLogSize 2000000000 # Log general information in error_log - change "info" to "debug" for # troubleshooting... LogLevel info #AccessLog syslog #ErrorLog syslog #PageLog syslog # Administrator user group... SystemGroup sys root lp # Only listen for connections from the local machine. Listen 0.0.0.0:631 Listen :::631 Listen /var/run/cups/cups.sock ServerName <snipped> # Show shared printers on the local network. Browsing Off BrowseOrder allow,deny # (Change '@LOCAL' to 'ALL' if using directed broadcasts from another subnet.) BrowseAllow @LOCAL # Default authentication type, when authentication is required... DefaultAuthType Basic # Restrict access to the server... <Location /> Order allow,deny Allow all </Location> # Restrict access to the admin pages... <Location /admin> AuthType Default Require user @SYSTEM Encryption Required Order allow,deny Allow all </Location> # Restrict access to configuration files... <Location /admin/conf> AuthType Default Require user @SYSTEM Encryption Required Order allow,deny Allow all </Location> # Set the default printer/job policies... <Policy default> # Job-related operations must be done by the owner or an administrator... <Limit Send-Document Send-URI Hold-Job Release-Job Restart-Job Purge-Jobs Set-Job-Attributes Create-Job-Subscription Renew-Subscription Cancel-Subscription Get-Notifications Reprocess-Job Cancel-Current-Job Suspend-Current-Job Resume-Job CUPS-Move-Job> Require user @OWNER @SYSTEM Order deny,allow </Limit> # All administration operations require an administrator to authenticate... <Limit CUPS-Add-Modify-Printer CUPS-Delete-Printer CUPS-Add-Modify-Class CUPS-Delete-Class CUPS-Set-Default> AuthType Default Require user @SYSTEM Order deny,allow </Limit> # All printer operations require a printer operator to authenticate... <Limit Pause-Printer Resume-Printer Enable-Printer Disable-Printer Pause-Printer-After-Current-Job Hold-New-Jobs Release-Held-New-Jobs Deactivate-Printer Activate-Printer Restart-Printer Shutdown-Printer Startup-Printer Promote-Job Schedule-Job-After CUPS-Accept-Jobs CUPS-Reject-Jobs> AuthType Default Require user @SYSTEM Order deny,allow </Limit> # Only the owner or an administrator can cancel or authenticate a job... <Limit Cancel-Job CUPS-Authenticate-Job> Require user @OWNER @SYSTEM Order deny,allow </Limit> <Limit All> Order allow,deny </Limit> </Policy>

  Read the article

• Why can't HTC Droid running OTA 2.1 communicate with RFCOMM?

  - by Brad Hein

  Yesterday we received OTA Android 2.1 on my wife's HTC Droid - HOORAY!!! I am finally able to load my carputer app on her phone. Well we loaded it, but it doesn't work. Specifically, it connects but sees no I/O!!! I paired, re-paired, and re-paired again, every time its the same problem: connect() says we connected successfully, but any attempt to send or receive data appears to work but no data ever arrives in the input buffer. The device I'm connecting to uses AT commands. ATI should respond with a device ID. That works fine when I run the app on my Moto Droid, but on the HTC droid, no data is ever present in the inputstream/buffer. Personally, I'm feeling pretty sure it's a bug or limitation in this release for the HTC (because the app works great on my Moto A855 Droid). Can anybody comment on the issue? Obligatory code snippets: Member variable defining my RFCOMM UUID static final UUID UUID_RFCOMM_GENERIC = UUID.fromString("00001101-0000-1000-8000-00805F9B34FB"); Parts of my connect() // make sure peer is defined as a valid device based on their MAC. If not then do it. if (mBTDevice == null) mBTDevice = mBTAdapter.getRemoteDevice(mPeerMAC); // Make an RFCOMM binding. try {mBTSocket = mBTDevice.createRfcommSocketToServiceRecord(UUID_RFCOMM_GENERIC); } catch (Exception e1) { msg ("connect(): Failed to bind to RFCOMM by UUID. msg=" + e1.getMessage()); return false; } msg ("connect(): Try to connect."); try { mBTSocket.connect(); } catch (Exception e) { msg ("connect(): Exception thrown during connect: " + e.getMessage()); return false; // there was a problem connecting... make a note of the particulars and move on. } msg ("connect(): CONNECTED!"); try { mBTOutputStream = mBTSocket.getOutputStream(); mBTInputStream = new BufferedInputStream (mBTSocket.getInputStream(),INPUT_BUFFER_SIZE); //msg ("Connecting non-buffered input stream..."); //mBTInputStream = mBTSocket.getInputStream(); } catch (Exception e) { msg ("connect(): Error attaching i/o streams to socket. msg=" + e.getMessage()); return false; } resetErrorCounters(); setConnected(true); return true; } Then I send "ATI\r" and expect something like "CAN OBD II" but I get nothing. mBTInputStream.available(), it seems, is ALWAYS zero, even when data should be in the input buffer. There are GOBS of trace messages being generated by the OS as viewed with adb logcat -v time Some of the more interesting ones: 05-17 19:44:21.447 D/BluetoothSppPort( 5809): connected to device service! 05-17 19:44:21.447 D/BluetoothSppPort( 5809): Creating a BluetoothSpp proxy object 05-17 19:44:21.467 D/BluetoothSppService( 74): createPort called! 05-17 19:44:21.467 D/BluetoothSppService( 74): createPort checking uuid 05-17 19:44:21.467 D/BluetoothSppService( 74): createPort UUID=00001101-0000-1000-8000-00805f9b34fb auth=true encrypt=true 05-17 19:44:21.467 D/BluetoothSppService( 74): createPort enforcing bluetooth perm 05-17 19:44:21.467 D/BluetoothSppService( 74): createPort creating a jbtlspp object 05-17 19:44:21.467 D/BluetoothSppService( 74): createPort checking if the btl spp object is valid 05-17 19:44:21.467 D/BluetoothSppService( 74): createPort try to create an spp container 05-17 19:44:21.467 D/BluetoothSppService( 74): createPort try to create security params 05-17 19:44:21.467 D/BluetoothSppService( 74): createPort Set Security L2 05-17 19:44:21.467 D/BluetoothSppService( 74): createPort spp port create 05-17 19:44:21.467 D/JBtlSpp ( 74): create: Entered 05-17 19:44:21.467 D/JBtlSpp ( 74): Calling NativeJBtlSpp_Create 05-17 19:44:21.467 D/JBtlSppNative( 74): NativeJBtlSpp_Create: Entered 05-17 19:44:21.467 D/JBtlSppNative( 74): NativeJBtlSpp_Create: Calling BTL_SPP_Remote_Create 05-17 19:44:21.477 D/JBtlSppNative( 74): NativeJBtlSpp_Create: BTL_SPP_Remote_Create returned 0, context:18 05-17 19:44:21.477 D/JBtlSppNative( 74): NativeJBtlSpp_Create: Setting context value in jContext out parm 05-17 19:44:21.477 D/JBtlSppNative( 74): NativeJBtlSpp_Create: Calling Java setValue(0x18) in context's class 05-17 19:44:21.477 D/JBtlProfileContext( 74): setValue: setValue called, value:24 05-17 19:44:21.477 D/JBtlSppNative( 74): create_spp_port_data: will use context struct 0 for the port 24 05-17 19:44:21.477 D/JBtlSppNative( 74): create_spp_port_data: spp port context 0 added 05-17 19:44:21.477 D/JBtlSppNative( 74): NativeJBtlSpp_Create:Exiting Successfully 05-17 19:44:21.477 D/JBtlSpp ( 74): After NativeJBtlSpp_Create, status=SUCCESS, Context = 24 05-17 19:44:21.477 D/JBtlRbtlServices( 74): addUser: Entered, userRefCount = 1 05-17 19:44:21.477 D/BluetoothSppService( 74): port create returned status SUCCESS 05-17 19:44:21.477 D/JBtlSpp ( 74): enable: Entered 05-17 19:44:21.477 D/JBtlSpp ( 74): enable: UUID=00001101-0000-1000-8000-00805f9b34fb 05-17 19:44:21.477 D/JBtlSppNative( 74): NativeJBtlSpp_Enable: Entered 05-17 19:44:21.487 D/JBtlSppNative( 74): NativeJBtlSpp_Enable: BTL_SPP_Enable returned 0 05-17 19:44:21.487 D/JBtlSppNative( 74): NativeJBtlSpp_Enable:Exiting 05-17 19:44:21.487 D/JBtlSpp ( 74): After NativeJBtlSpp_Enable, status=SUCCESS 05-17 19:44:21.487 D/JBtlSpp ( 74): enable: Exiting 05-17 19:44:21.487 D/BluetoothSppService( 74): port enable returned status SUCCESS 05-17 19:44:21.487 D/BluetoothSppService( 74): connectPort called! 05-17 19:44:21.497 D/BluetoothSppService( 74): connectPort received bdaddress:00:18:E4:1D:23:9B 05-17 19:44:21.527 D/BluetoothSppService( 74): Trying to connect to 00:18:E4:1D:23:9B 05-17 19:44:21.527 D/JBtlSpp ( 74): setServiceName: Entered 05-17 19:44:21.527 D/JBtlSppNative( 74): NativeJBtlSpp_SetServiceName: Entered 05-17 19:44:21.547 D/JBtlSppNative( 74): NativeJBtlSpp_SetServiceName: native func returned 0 05-17 19:44:21.547 D/JBtlSppNative( 74): NativeJBtlSpp_SetServiceName:Exiting 05-17 19:44:21.547 D/JBtlSpp ( 74): After setServiceName, status=SUCCESS 05-17 19:44:21.547 D/JBtlSpp ( 74): setServiceName: Exiting 05-17 19:44:21.557 D/BluetoothSppService( 74): port setServiceName returned status SUCCESS 05-17 19:44:21.587 D/JBtlSpp ( 74): connect: Entered connecting to 00:18:E4:1D:23:9B 05-17 19:44:21.587 D/JBtlSppNative( 74): NativeJBtlSpp_Connect: Entered 05-17 19:44:21.597 D/JBtlSppNative( 74): NativeJBtlSpp_Connect: BTL_SPP_Connect returned 2 05-17 19:44:21.597 D/JBtlSppNative( 74): NativeJBtlSpp_Connect:Exiting 05-17 19:44:21.597 D/JBtlSpp ( 74): After NativeJBtlSpp_Connect, status=PENDING 05-17 19:44:21.747 D/AK8973 ( 61): Compass CLOSE 05-17 19:44:21.887 W/Process ( 74): Unable to open /proc/5749/status 05-17 19:44:21.917 I/ActivityManager( 74): Displayed activity com.gtosoft.dash/.Dash: 1279 ms (total 1279 ms) 05-17 19:44:24.047 D/ ( 74): signal_BTEVENT_ACCESSIBLE_CHANGE: Entered 05-17 19:44:24.047 D/ ( 74): signal_BTEVENT_ACCESSIBLE_CHANGE: Calling Java Accessible Change callback 05-17 19:44:24.047 D/JBtlBmg ( 74): nativeAccessibleChange 05-17 19:44:24.087 D/BluetoothService( 74): Callback - accessbileChange, btErrCode = NO_ERROR, mode = CONNECTABLE_ONLY 05-17 19:44:24.087 D/BluetoothService( 74): Sending ACTION_SCAN_MODE_CHANGED intent, mode = 21 05-17 19:44:24.087 D/ ( 74): signal_BTEVENT_ACCESSIBLE_CHANGE: Exiting 05-17 19:44:24.097 D/ ( 74): signal_BTEVENT_LINK_CONNECT_CNF: Entered 05-17 19:44:24.097 D/ ( 74): signal_BTEVENT_LINK_CONNECT_CNF: context: 1, errCode: 0 05-17 19:44:24.097 D/ ( 74): signal_BTEVENT_LINK_CONNECT_CNF: Calling Java Link Connect Confirmation callback 05-17 19:44:24.097 D/JBtlBmg ( 74): nativeLinkConnectCnf 05-17 19:44:24.107 D/BluetoothService( 74): Callback - linkConnectCnf, btErrCode = NO_ERROR, bdAddr = 00:18:E4:1D:23:9B 05-17 19:44:24.117 D/JBtlBmg ( 74): getKnownDeviceInfo: Entered 05-17 19:44:24.117 D/JBtlBmg ( 74): getKnownDeviceInfo: Calling NativeJBtlBmg_GetKnownDeviceInfo 05-17 19:44:24.137 D/ ( 74): NativeJBtlBmg_GetKnownDeviceInfo: Entered 05-17 19:44:24.137 D/ ( 74): NativeJBtlBmg_GetKnownDeviceInfo: Calling BTL_BMG_GetKnownDeviceInfo 05-17 19:44:24.227 D/JBtlBmgJniKnownDeviceInfo( 74): setValues: Entered 05-17 19:44:24.227 D/ ( 74): NativeJBtlBmg_GetKnownDeviceInfo:Exiting 05-17 19:44:24.227 D/JBtlBmg ( 74): getKnownDeviceInfo: After NativeJBtlBmg_GetKnownDeviceInfo, status=SUCCESS 05-17 19:44:24.227 D/JBtlBmg ( 74): getKnownDeviceInfo: Exiting 05-17 19:44:24.227 D/BluetoothService( 74): onRemoteDeviceConnected, device 00:18:E4:1D:23:9B is Paired 05-17 19:44:24.227 D/BluetoothService( 74): Sending ACTION_ACL_CONNECTED intent, address = 00:18:E4:1D:23:9B 05-17 19:44:24.227 D/BluetoothA2dpService( 74): Received intent with action: android.bluetooth.device.action.ACL_CONNECTED 05-17 19:44:24.227 D/ ( 74): signal_BTEVENT_LINK_CONNECT_CNF: Exiting 05-17 19:44:24.757 D/JBtlAg ( 163): setIndicatorValue: entered 05-17 19:44:24.767 I/JBtlAg ( 163): After NativeJBtlAg_SetIndicatorValue, status = SUCCESS 05-17 19:44:24.767 D/JBtlAg ( 163): setIndicatorValue: exiting 05-17 19:44:24.807 D/JBtlSppNative( 74): signal_SPP_EVENT_OPEN: Entered 05-17 19:44:24.807 D/JBtlSppNative( 74): signal_SPP_EVENT_OPEN: status: 0 context:24 05-17 19:44:24.827 D/JBtlSpp ( 74): nativeCb_open: Entered from 00:18:E4:1D:23:9B 05-17 19:44:24.827 D/JBtlSpp ( 74): nativeCb_open: Calling callback 05-17 19:44:24.827 D/BluetoothSppService( 74): connected called! 05-17 19:44:24.847 D/JBtlSpp ( 74): connect: Exiting 05-17 19:44:24.847 D/BluetoothSppService( 74): port connect returned status SUCCESS 05-17 19:44:24.847 D/JBtlSppNative( 74): signal_SPP_EVENT_OPEN: Exiting 05-17 19:44:24.847 D/JBtlSppNative( 74): signal_SPP_EVENT_MODEM_STATUS_IND: Entered 05-17 19:44:24.847 D/JBtlSppNative( 74): signal_SPP_EVENT_MODEM_STATUS_IND: Exiting 05-17 19:44:25.424 D/BluetoothSppService( 74): writeSync called! 05-17 19:44:25.424 D/JBtlSpp ( 74): write: Entered 05-17 19:44:25.427 D/JBtlSppNative( 74): NativeJBtlSpp_WriteNative: Entered 05-17 19:44:25.427 D/JBtlSppNative( 74): NativeJBtlSpp_WriteNative: BTL_SPP_WriteSync returned 0 written: 6 total: 0/6 05-17 19:44:25.437 D/JBtlSppNative( 74): signal_SPP_EVENT_TX_DATA_COMPLETE: Entered 05-17 19:44:25.437 D/JBtlSppNative( 74): signal_SPP_EVENT_TX_DATA_COMPLETE: status: 0 context:24 txDataLen:6 05-17 19:44:25.437 D/JBtlSppNative( 74): signal_SPP_EVENT_TX_DATA_COMPLETE: Exiting ok 05-17 19:44:25.437 D/JBtlSppNative( 74): NativeJBtlSpp_WriteNative: written 6 05-17 19:44:25.437 D/JBtlSppNative( 74): NativeJBtlSpp_WriteNative:Exiting with 0 05-17 19:44:25.437 D/JBtlSppNative( 74): NativeJBtlSpp_WriteNative: returning 6 bytes 05-17 19:44:25.437 D/JBtlSpp ( 74): After write, status=SUCCESS 05-17 19:44:25.437 D/JBtlSpp ( 74): write: Exiting 05-17 19:44:25.437 D/BluetoothSppPort( 5809): written 6 bytes 05-17 19:44:25.467 D/JBtlSppNative( 74): signal_SPP_EVENT_RX_DATA_IND: Entered 05-17 19:44:25.467 D/JBtlSppNative( 74): signal_SPP_EVENT_RX_DATA_IND: status: 0 context: 24 rxDataLen: 1 05-17 19:44:25.467 D/JBtlSppNative( 74): signal_SPP_EVENT_RX_DATA_IND: Exiting 05-17 19:44:25.477 D/JBtlSppNative( 74): signal_SPP_EVENT_RX_DATA_IND: Entered 05-17 19:44:25.477 D/JBtlSppNative( 74): signal_SPP_EVENT_RX_DATA_IND: status: 0 context: 24 rxDataLen: 5 05-17 19:44:25.477 D/JBtlSppNative( 74): signal_SPP_EVENT_RX_DATA_IND: Exiting 05-17 19:44:25.487 D/JBtlSppNative( 74): signal_SPP_EVENT_RX_DATA_IND: Entered 05-17 19:44:25.487 D/JBtlSppNative( 74): signal_SPP_EVENT_RX_DATA_IND: status: 0 context: 24 rxDataLen: 10 05-17 19:44:25.487 D/JBtlSppNative( 74): signal_SPP_EVENT_RX_DATA_IND: Exiting 05-17 19:44:25.497 D/JBtlSppNative( 74): signal_SPP_EVENT_RX_DATA_IND: Entered 05-17 19:44:25.497 D/JBtlSppNative( 74): signal_SPP_EVENT_RX_DATA_IND: status: 0 context: 24 rxDataLen: 7 05-17 19:44:25.497 D/JBtlSppNative( 74): signal_SPP_EVENT_RX_DATA_IND: Exiting 05-17 19:44:27.930 W/ActivityManager( 74): Activity destroy timeout for HistoryRecord{447e0d48 com.gtosoft.dash/.Dash} 05-17 19:44:29.907 D/dalvikvm( 448): GC freed 78 objects / 3664 bytes in 153ms 05-17 19:44:29.917 D/BluetoothSppService( 74): writeSync called! 05-17 19:44:29.917 D/JBtlSpp ( 74): write: Entered 05-17 19:44:29.917 D/JBtlSppNative( 74): NativeJBtlSpp_WriteNative: Entered 05-17 19:44:29.927 D/JBtlSppNative( 74): NativeJBtlSpp_WriteNative: BTL_SPP_WriteSync returned 0 written: 6 total: 0/6 05-17 19:44:29.937 D/JBtlSppNative( 74): signal_SPP_EVENT_TX_DATA_COMPLETE: Entered 05-17 19:44:29.937 D/JBtlSppNative( 74): signal_SPP_EVENT_TX_DATA_COMPLETE: status: 0 context:24 txDataLen:6 05-17 19:44:29.937 D/JBtlSppNative( 74): signal_SPP_EVENT_TX_DATA_COMPLETE: Exiting ok 05-17 19:44:29.937 D/JBtlSppNative( 74): NativeJBtlSpp_WriteNative: written 6 05-17 19:44:29.937 D/JBtlSppNative( 74): NativeJBtlSpp_WriteNative:Exiting with 0 05-17 19:44:29.937 D/JBtlSppNative( 74): NativeJBtlSpp_WriteNative: returning 6 bytes 05-17 19:44:29.937 D/JBtlSpp ( 74): After write, status=SUCCESS 05-17 19:44:29.937 D/JBtlSpp ( 74): write: Exiting

  Read the article

• Database Tutorial: The method open() is undefined for the type MainActivity.DBAdapter

  - by user2203633

  I am trying to do this database tutorial on SQLite Eclipse: https://www.youtube.com/watch?v=j-IV87qQ00M But I get a few errors at the end.. at db.ppen(); i get error: The method open() is undefined for the type MainActivity.DBAdapter and similar for insert record and close. MainActivity: package com.example.studentdatabase; import java.io.File; import java.io.FileNotFoundException; import java.io.FileOutputStream; import java.io.IOException; import java.io.InputStream; import java.io.OutputStream; import android.app.Activity; import android.app.ListActivity; import android.content.Intent; import android.database.Cursor; import android.os.Bundle; import android.util.Log; import android.view.LayoutInflater; import android.view.View; import android.view.ViewGroup; import android.widget.BaseAdapter; import android.widget.Button; import android.widget.Toast; public class MainActivity extends Activity { /** Called when the activity is first created. */ //DBAdapter db = new DBAdapter(this); @Override public void onCreate(Bundle savedInstanceState) { super.onCreate(savedInstanceState); setContentView(R.layout.activity_main); Button addBtn = (Button)findViewById(R.id.add); addBtn.setOnClickListener(new View.OnClickListener() { @Override public void onClick(View v) { Intent i = new Intent(MainActivity.this, addassignment.class); startActivity(i); } }); try { String destPath = "/data/data/" + getPackageName() + "/databases/AssignmentDB"; File f = new File(destPath); if (!f.exists()) { CopyDB( getBaseContext().getAssets().open("mydb"), new FileOutputStream(destPath)); } } catch (FileNotFoundException e) { e.printStackTrace(); } catch (IOException e) { e.printStackTrace(); } DBAdapter db = new DBAdapter(); //---add an assignment--- db.open(); long id = db.insertRecord("Hello World", "2/18/2012", "DPR 224", "First Android Project"); id = db.insertRecord("Workbook Exercises", "3/1/2012", "MAT 100", "Do odd numbers"); db.close(); //---get all Records--- /* db.open(); Cursor c = db.getAllRecords(); if (c.moveToFirst()) { do { DisplayRecord(c); } while (c.moveToNext()); } db.close(); */ /* //---get a Record--- db.open(); Cursor c = db.getRecord(2); if (c.moveToFirst()) DisplayRecord(c); else Toast.makeText(this, "No Assignments found", Toast.LENGTH_LONG).show(); db.close(); */ //---update Record--- /* db.open(); if (db.updateRecord(1, "Hello Android", "2/19/2012", "DPR 224", "First Android Project")) Toast.makeText(this, "Update successful.", Toast.LENGTH_LONG).show(); else Toast.makeText(this, "Update failed.", Toast.LENGTH_LONG).show(); db.close(); */ /* //---delete a Record--- db.open(); if (db.deleteRecord(1)) Toast.makeText(this, "Delete successful.", Toast.LENGTH_LONG).show(); else Toast.makeText(this, "Delete failed.", Toast.LENGTH_LONG).show(); db.close(); */ } private class DBAdapter extends BaseAdapter { private LayoutInflater mInflater; //private ArrayList<> @Override public int getCount() { return 0; } @Override public Object getItem(int arg0) { return null; } @Override public long getItemId(int arg0) { return 0; } @Override public View getView(int arg0, View arg1, ViewGroup arg2) { return null; } } public void CopyDB(InputStream inputStream, OutputStream outputStream) throws IOException { //---copy 1K bytes at a time--- byte[] buffer = new byte[1024]; int length; while ((length = inputStream.read(buffer)) > 0) { outputStream.write(buffer, 0, length); } inputStream.close(); outputStream.close(); } public void DisplayRecord(Cursor c) { Toast.makeText(this, "id: " + c.getString(0) + "\n" + "Title: " + c.getString(1) + "\n" + "Due Date: " + c.getString(2), Toast.LENGTH_SHORT).show(); } public void addAssignment(View view) { Intent i = new Intent("com.pinchtapzoom.addassignment"); startActivity(i); Log.d("TAG", "Clicked"); } } DBAdapter code: package com.example.studentdatabase; public class DBAdapter { public static final String KEY_ROWID = "id"; public static final String KEY_TITLE = "title"; public static final String KEY_DUEDATE = "duedate"; public static final String KEY_COURSE = "course"; public static final String KEY_NOTES = "notes"; private static final String TAG = "DBAdapter"; private static final String DATABASE_NAME = "AssignmentsDB"; private static final String DATABASE_TABLE = "assignments"; private static final int DATABASE_VERSION = 2; private static final String DATABASE_CREATE = "create table if not exists assignments (id integer primary key autoincrement, " + "title VARCHAR not null, duedate date, course VARCHAR, notes VARCHAR );"; private final Context context; private DatabaseHelper DBHelper; private SQLiteDatabase db; public DBAdapter(Context ctx) { this.context = ctx; DBHelper = new DatabaseHelper(context); } private static class DatabaseHelper extends SQLiteOpenHelper { DatabaseHelper(Context context) { super(context, DATABASE_NAME, null, DATABASE_VERSION); } @Override public void onCreate(SQLiteDatabase db) { try { db.execSQL(DATABASE_CREATE); } catch (SQLException e) { e.printStackTrace(); } } @Override public void onUpgrade(SQLiteDatabase db, int oldVersion, int newVersion) { Log.w(TAG, "Upgrading database from version " + oldVersion + " to " + newVersion + ", which will destroy all old data"); db.execSQL("DROP TABLE IF EXISTS contacts"); onCreate(db); } } //---opens the database--- public DBAdapter open() throws SQLException { db = DBHelper.getWritableDatabase(); return this; } //---closes the database--- public void close() { DBHelper.close(); } //---insert a record into the database--- public long insertRecord(String title, String duedate, String course, String notes) { ContentValues initialValues = new ContentValues(); initialValues.put(KEY_TITLE, title); initialValues.put(KEY_DUEDATE, duedate); initialValues.put(KEY_COURSE, course); initialValues.put(KEY_NOTES, notes); return db.insert(DATABASE_TABLE, null, initialValues); } //---deletes a particular record--- public boolean deleteContact(long rowId) { return db.delete(DATABASE_TABLE, KEY_ROWID + "=" + rowId, null) > 0; } //---retrieves all the records--- public Cursor getAllRecords() { return db.query(DATABASE_TABLE, new String[] {KEY_ROWID, KEY_TITLE, KEY_DUEDATE, KEY_COURSE, KEY_NOTES}, null, null, null, null, null); } //---retrieves a particular record--- public Cursor getRecord(long rowId) throws SQLException { Cursor mCursor = db.query(true, DATABASE_TABLE, new String[] {KEY_ROWID, KEY_TITLE, KEY_DUEDATE, KEY_COURSE, KEY_NOTES}, KEY_ROWID + "=" + rowId, null, null, null, null, null); if (mCursor != null) { mCursor.moveToFirst(); } return mCursor; } //---updates a record--- public boolean updateRecord(long rowId, String title, String duedate, String course, String notes) { ContentValues args = new ContentValues(); args.put(KEY_TITLE, title); args.put(KEY_DUEDATE, duedate); args.put(KEY_COURSE, course); args.put(KEY_NOTES, notes); return db.update(DATABASE_TABLE, args, KEY_ROWID + "=" + rowId, null) > 0; } } addassignment code: package com.example.studentdatabase; public class addassignment extends Activity { DBAdapter db = new DBAdapter(this); @Override protected void onCreate(Bundle savedInstanceState) { super.onCreate(savedInstanceState); setContentView(R.layout.add); } public void addAssignment(View v) { Log.d("test", "adding"); //get data from form EditText nameTxt = (EditText)findViewById(R.id.editTitle); EditText dateTxt = (EditText)findViewById(R.id.editDuedate); EditText courseTxt = (EditText)findViewById(R.id.editCourse); EditText notesTxt = (EditText)findViewById(R.id.editNotes); db.open(); long id = db.insertRecord(nameTxt.getText().toString(), dateTxt.getText().toString(), courseTxt.getText().toString(), notesTxt.getText().toString()); db.close(); nameTxt.setText(""); dateTxt.setText(""); courseTxt.setText(""); notesTxt.setText(""); Toast.makeText(addassignment.this,"Assignment Added", Toast.LENGTH_LONG).show(); } public void viewAssignments(View v) { Intent i = new Intent(this, MainActivity.class); startActivity(i); } } What is wrong here? Thanks in advance.

  Read the article

• Microsoft and jQuery

  - by Rick Strahl

  The jQuery JavaScript library has been steadily getting more popular and with recent developments from Microsoft, jQuery is also getting ever more exposure on the ASP.NET platform including now directly from Microsoft. jQuery is a light weight, open source DOM manipulation library for JavaScript that has changed how many developers think about JavaScript. You can download it and find more information on jQuery on www.jquery.com. For me jQuery has had a huge impact on how I develop Web applications and was probably the main reason I went from dreading to do JavaScript development to actually looking forward to implementing client side JavaScript functionality. It has also had a profound impact on my JavaScript skill level for me by seeing how the library accomplishes things (and often reviewing the terse but excellent source code). jQuery made an uncomfortable development platform (JavaScript + DOM) a joy to work on. Although jQuery is by no means the only JavaScript library out there, its ease of use, small size, huge community of plug-ins and pure usefulness has made it easily the most popular JavaScript library available today. As a long time jQuery user, I’ve been excited to see the developments from Microsoft that are bringing jQuery to more ASP.NET developers and providing more integration with jQuery for ASP.NET’s core features rather than relying on the ASP.NET AJAX library. Microsoft and jQuery – making Friends jQuery is an open source project but in the last couple of years Microsoft has really thrown its weight behind supporting this open source library as a supported component on the Microsoft platform. When I say supported I literally mean supported: Microsoft now offers actual tech support for jQuery as part of their Product Support Services (PSS) as jQuery integration has become part of several of the ASP.NET toolkits and ships in several of the default Web project templates in Visual Studio 2010. The ASP.NET MVC 3 framework (still in Beta) also uses jQuery for a variety of client side support features including client side validation and we can look forward toward more integration of client side functionality via jQuery in both MVC and WebForms in the future. In other words jQuery is becoming an optional but included component of the ASP.NET platform. PSS support means that support staff will answer jQuery related support questions as part of any support incidents related to ASP.NET which provides some piece of mind to some corporate development shops that require end to end support from Microsoft. In addition to including jQuery and supporting it, Microsoft has also been getting involved in providing development resources for extending jQuery’s functionality via plug-ins. Microsoft’s last version of the Microsoft Ajax Library – which is the successor to the native ASP.NET AJAX Library – included some really cool functionality for client templates, databinding and localization. As it turns out Microsoft has rebuilt most of that functionality using jQuery as the base API and provided jQuery plug-ins of these components. Very recently these three plug-ins were submitted and have been approved for inclusion in the official jQuery plug-in repository and been taken over by the jQuery team for further improvements and maintenance. Even more surprising: The jQuery-templates component has actually been approved for inclusion in the next major update of the jQuery core in jQuery V1.5, which means it will become a native feature that doesn’t require additional script files to be loaded. Imagine this – an open source contribution from Microsoft that has been accepted into a major open source project for a core feature improvement. Microsoft has come a long way indeed! What the Microsoft Involvement with jQuery means to you For Microsoft jQuery support is a strategic decision that affects their direction in client side development, but nothing stopped you from using jQuery in your applications prior to Microsoft’s official backing and in fact a large chunk of developers did so readily prior to Microsoft’s announcement. Official support from Microsoft brings a few benefits to developers however. jQuery support in Visual Studio 2010 means built-in support for jQuery IntelliSense, automatically added jQuery scripts in many projects types and a common base for client side functionality that actually uses what most developers are already using. If you have already been using jQuery and were worried about straying from the Microsoft line and their internal Microsoft Ajax Library – worry no more. With official support and the change in direction towards jQuery Microsoft is now following along what most in the ASP.NET community had already been doing by using jQuery, which is likely the reason for Microsoft’s shift in direction in the first place. ASP.NET AJAX and the Microsoft AJAX Library weren’t bad technology – there was tons of useful functionality buried in these libraries. However, these libraries never got off the ground, mainly because early incarnations were squarely aimed at control/component developers rather than application developers. For all the functionality that these controls provided for control developers they lacked in useful and easily usable application developer functionality that was easily accessible in day to day client side development. The result was that even though Microsoft shipped support for these tools in the box (in .NET 3.5 and 4.0), other than for the internal support in ASP.NET for things like the UpdatePanel and the ASP.NET AJAX Control Toolkit as well as some third party vendors, the Microsoft client libraries were largely ignored by the developer community opening the door for other client side solutions. Microsoft seems to be acknowledging developer choice in this case: Many more developers were going down the jQuery path rather than using the Microsoft built libraries and there seems to be little sense in continuing development of a technology that largely goes unused by the majority of developers. Kudos for Microsoft for recognizing this and gracefully changing directions. Note that even though there will be no further development in the Microsoft client libraries they will continue to be supported so if you’re using them in your applications there’s no reason to start running for the exit in a panic and start re-writing everything with jQuery. Although that might be a reasonable choice in some cases, jQuery and the Microsoft libraries work well side by side so that you can leave existing solutions untouched even as you enhance them with jQuery. The Microsoft jQuery Plug-ins – Solid Core Features One of the most interesting developments in Microsoft’s embracing of jQuery is that Microsoft has started contributing to jQuery via standard mechanism set for jQuery developers: By submitting plug-ins. Microsoft took some of the nicest new features of the unpublished Microsoft Ajax Client Library and re-wrote these components for jQuery and then submitted them as plug-ins to the jQuery plug-in repository. Accepted plug-ins get taken over by the jQuery team and that’s exactly what happened with the three plug-ins submitted by Microsoft with the templating plug-in even getting slated to be published as part of the jQuery core in the next major release (1.5). The following plug-ins are provided by Microsoft: jQuery Templates – a client side template rendering engine jQuery Data Link – a client side databinder that can synchronize changes without code jQuery Globalization – provides formatting and conversion features for dates and numbers The first two are ports of functionality that was slated for the Microsoft Ajax Library while functionality for the globalization library provides functionality that was already found in the original ASP.NET AJAX library. To me all three plug-ins address a pressing need in client side applications and provide functionality I’ve previously used in other incarnations, but with more complete implementations. Let’s take a close look at these plug-ins. jQuery Templates http://api.jquery.com/category/plugins/templates/ Client side templating is a key component for building rich JavaScript applications in the browser. Templating on the client lets you avoid from manually creating markup by creating DOM nodes and injecting them individually into the document via code. Rather you can create markup templates – similar to the way you create classic ASP server markup – and merge data into these templates to render HTML which you can then inject into the document or replace existing content with. Output from templates are rendered as a jQuery matched set and can then be easily inserted into the document as needed. Templating is key to minimize client side code and reduce repeated code for rendering logic. Instead a single template can be used in many places for updating and adding content to existing pages. Further if you build pure AJAX interfaces that rely entirely on client rendering of the initial page content, templates allow you to a use a single markup template to handle all rendering of each specific HTML section/element. I’ve used a number of different client rendering template engines with jQuery in the past including jTemplates (a PHP style templating engine) and a modified version of John Resig’s MicroTemplating engine which I built into my own set of libraries because it’s such a commonly used feature in my client side applications. jQuery templates adds a much richer templating model that allows for sub-templates and access to the data items. Like John Resig’s original Micro Template engine, the core basics of the templating engine create JavaScript code which means that templates can include JavaScript code. To give you a basic idea of how templates work imagine I have an application that downloads a set of stock quotes based on a symbol list then displays them in the document. To do this you can create an ‘item’ template that describes how each of the quotes is renderd as a template inside of the document: <script id="stockTemplate" type="text/x-jquery-tmpl"> <div id="divStockQuote" class="errordisplay" style="width: 500px;"> <div class="label">Company:</div><div><b>${Company}(${Symbol})</b></div> <div class="label">Last Price:</div><div>${LastPrice}</div> <div class="label">Net Change:</div><div> {{if NetChange > 0}} <b style="color:green" >${NetChange}</b> {{else}} <b style="color:red" >${NetChange}</b> {{/if}} </div> <div class="label">Last Update:</div><div>${LastQuoteTimeString}</div> </div> </script> The ‘template’ is little more than HTML with some markup expressions inside of it that define the template language. Notice the embedded ${} expressions which reference data from the quote objects returned from an AJAX call on the server. You can embed any JavaScript or value expression in these template expressions. There are also a number of structural commands like {{if}} and {{each}} that provide for rudimentary logic inside of your templates as well as commands ({{tmpl}} and {{wrap}}) for nesting templates. You can find more about the full set of markup expressions available in the documentation. To load up this data you can use code like the following: <script type="text/javascript"> //var Proxy = new ServiceProxy("../PageMethods/PageMethodsService.asmx/"); $(document).ready(function () { $("#btnGetQuotes").click(GetQuotes); }); function GetQuotes() { var symbols = $("#txtSymbols").val().split(","); $.ajax({ url: "../PageMethods/PageMethodsService.asmx/GetStockQuotes", data: JSON.stringify({ symbols: symbols }), // parameter map type: "POST", // data has to be POSTed contentType: "application/json", timeout: 10000, dataType: "json", success: function (result) { var quotes = result.d; var jEl = $("#stockTemplate").tmpl(quotes); $("#quoteDisplay").empty().append(jEl); }, error: function (xhr, status) { alert(status + "\r\n" + xhr.responseText); } }); }; </script> In this case an ASMX AJAX service is called to retrieve the stock quotes. The service returns an array of quote objects. The result is returned as an object with the .d property (in Microsoft service style) that returns the actual array of quotes. The template is applied with: var jEl = $("#stockTemplate").tmpl(quotes); which selects the template script tag and uses the .tmpl() function to apply the data to it. The result is a jQuery matched set of elements that can then be appended to the quote display element in the page. The template is merged against an array in this example. When the result is an array the template is automatically applied to each each array item. If you pass a single data item – like say a stock quote – the template works exactly the same way but is applied only once. Templates also have access to a $data item which provides the current data item and information about the tempalte that is currently executing. This makes it possible to keep context within the context of the template itself and also to pass context from a parent template to a child template which is very powerful. Templates can be evaluated by using the template selector and calling the .tmpl() function on the jQuery matched set as shown above or you can use the static $.tmpl() function to provide a template as a string. This allows you to dynamically create templates in code or – more likely – to load templates from the server via AJAX calls. In short there are options The above shows off some of the basics, but there’s much for functionality available in the template engine. Check the documentation link for more information and links to additional examples. The plug-in download also comes with a number of examples that demonstrate functionality. jQuery templates will become a native component in jQuery Core 1.5, so it’s definitely worthwhile checking out the engine today and get familiar with this interface. As much as I’m stoked about templating becoming part of the jQuery core because it’s such an integral part of many applications, there are also a couple shortcomings in the current incarnation: Lack of Error Handling Currently if you embed an expression that is invalid it’s simply not rendered. There’s no error rendered into the template nor do the various  template functions throw errors which leaves finding of bugs as a runtime exercise. I would like some mechanism – optional if possible – to be able to get error info of what is failing in a template when it’s rendered. No String Output Templates are always rendered into a jQuery matched set and there’s no way that I can see to directly render to a string. String output can be useful for debugging as well as opening up templating for creating non-HTML string output. Limited JavaScript Access Unlike John Resig’s original MicroTemplating Engine which was entirely based on JavaScript code generation these templates are limited to a few structured commands that can ‘execute’. There’s no code execution inside of script code which means you’re limited to calling expressions available in global objects or the data item passed in. This may or may not be a big deal depending on the complexity of your template logic. Error handling has been discussed quite a bit and it’s likely there will be some solution to that particualar issue by the time jQuery templates ship. The others are relatively minor issues but something to think about anyway. jQuery Data Link http://api.jquery.com/category/plugins/data-link/ jQuery Data Link provides the ability to do two-way data binding between input controls and an underlying object’s properties. The typical scenario is linking a textbox to a property of an object and have the object updated when the text in the textbox is changed and have the textbox change when the value in the object or the entire object changes. The plug-in also supports converter functions that can be applied to provide the conversion logic from string to some other value typically necessary for mapping things like textbox string input to say a number property and potentially applying additional formatting and calculations. In theory this sounds great, however in reality this plug-in has some serious usability issues. Using the plug-in you can do things like the following to bind data: person = { firstName: "rick", lastName: "strahl"}; $(document).ready( function() { // provide for two-way linking of inputs $("form").link(person); // bind to non-input elements explicitly $("#objFirst").link(person, { firstName: { name: "objFirst", convertBack: function (value, source, target) { $(target).text(value); } } }); $("#objLast").link(person, { lastName: { name: "objLast", convertBack: function (value, source, target) { $(target).text(value); } } }); }); This code hooks up two-way linking between a couple of textboxes on the page and the person object. The first line in the .ready() handler provides mapping of object to form field with the same field names as properties on the object. Note that .link() does NOT bind items into the textboxes when you call .link() – changes are mapped only when values change and you move out of the field. Strike one. The two following commands allow manual binding of values to specific DOM elements which is effectively a one-way bind. You specify the object and a then an explicit mapping where name is an ID in the document. The converter is required to explicitly assign the value to the element. Strike two. You can also detect changes to the underlying object and cause updates to the input elements bound. Unfortunately the syntax to do this is not very natural as you have to rely on the jQuery data object. To update an object’s properties and get change notification looks like this: function updateFirstName() { $(person).data("firstName", person.firstName + " (code updated)"); } This works fine in causing any linked fields to be updated. In the bindings above both the firstName input field and objFirst DOM element gets updated. But the syntax requires you to use a jQuery .data() call for each property change to ensure that the changes are tracked properly. Really? Sure you’re binding through multiple layers of abstraction now but how is that better than just manually assigning values? The code savings (if any) are going to be minimal. As much as I would like to have a WPF/Silverlight/Observable-like binding mechanism in client script, this plug-in doesn’t help much towards that goal in its current incarnation. While you can bind values, the ‘binder’ is too limited to be really useful. If initial values can’t be assigned from the mappings you’re going to end up duplicating work loading the data using some other mechanism. There’s no easy way to re-bind data with a different object altogether since updates trigger only through the .data members. Finally, any non-input elements have to be bound via code that’s fairly verbose and frankly may be more voluminous than what you might write by hand for manual binding and unbinding. Two way binding can be very useful but it has to be easy and most importantly natural. If it’s more work to hook up a binding than writing a couple of lines to do binding/unbinding this sort of thing helps very little in most scenarios. In talking to some of the developers the feature set for Data Link is not complete and they are still soliciting input for features and functionality. If you have ideas on how you want this feature to be more useful get involved and post your recommendations. As it stands, it looks to me like this component needs a lot of love to become useful. For this component to really provide value, bindings need to be able to be refreshed easily and work at the object level, not just the property level. It seems to me we would be much better served by a model binder object that can perform these binding/unbinding tasks in bulk rather than a tool where each link has to be mapped first. I also find the choice of creating a jQuery plug-in questionable – it seems a standalone object – albeit one that relies on the jQuery library – would provide a more intuitive interface than the current forcing of options onto a plug-in style interface. Out of the three Microsoft created components this is by far the least useful and least polished implementation at this point. jQuery Globalization http://github.com/jquery/jquery-global Globalization in JavaScript applications often gets short shrift and part of the reason for this is that natively in JavaScript there’s little support for formatting and parsing of numbers and dates. There are a number of JavaScript libraries out there that provide some support for globalization, but most are limited to a particular portion of globalization. As .NET developers we’re fairly spoiled by the richness of APIs provided in the framework and when dealing with client development one really notices the lack of these features. While you may not necessarily need to localize your application the globalization plug-in also helps with some basic tasks for non-localized applications: Dealing with formatting and parsing of dates and time values. Dates in particular are problematic in JavaScript as there are no formatters whatsoever except the .toString() method which outputs a verbose and next to useless long string. With the globalization plug-in you get a good chunk of the formatting and parsing functionality that the .NET framework provides on the server. You can write code like the following for example to format numbers and dates: var date = new Date(); var output = $.format(date, "MMM. dd, yy") + "\r\n" + $.format(date, "d") + "\r\n" + // 10/25/2010 $.format(1222.32213, "N2") + "\r\n" + $.format(1222.33, "c") + "\r\n"; alert(output); This becomes even more useful if you combine it with templates which can also include any JavaScript expressions. Assuming the globalization plug-in is loaded you can create template expressions that use the $.format function. Here’s the template I used earlier for the stock quote again with a couple of formats applied: <script id="stockTemplate" type="text/x-jquery-tmpl"> <div id="divStockQuote" class="errordisplay" style="width: 500px;"> <div class="label">Company:</div><div><b>${Company}(${Symbol})</b></div> <div class="label">Last Price:</div> <div>${$.format(LastPrice,"N2")}</div> <div class="label">Net Change:</div><div> {{if NetChange > 0}} <b style="color:green" >${NetChange}</b> {{else}} <b style="color:red" >${NetChange}</b> {{/if}} </div> <div class="label">Last Update:</div> <div>${$.format(LastQuoteTime,"MMM dd, yyyy")}</div> </div> </script> There are also parsing methods that can parse dates and numbers from strings into numbers easily: alert($.parseDate("25.10.2010")); alert($.parseInt("12.222")); // de-DE uses . for thousands separators As you can see culture specific options are taken into account when parsing. The globalization plugin provides rich support for a variety of locales: Get a list of all available cultures Query cultures for culture items (like currency symbol, separators etc.) Localized string names for all calendar related items (days of week, months) Generated off of .NET’s supported locales In short you get much of the same functionality that you already might be using in .NET on the server side. The plugin includes a huge number of locales and an Globalization.all.min.js file that contains the text defaults for each of these locales as well as small locale specific script files that define each of the locale specific settings. It’s highly recommended that you NOT use the huge globalization file that includes all locales, but rather add script references to only those languages you explicitly care about. Overall this plug-in is a welcome helper. Even if you use it with a single locale (like en-US) and do no other localization, you’ll gain solid support for number and date formatting which is a vital feature of many applications. Changes for Microsoft It’s good to see Microsoft coming out of its shell and away from the ‘not-built-here’ mentality that has been so pervasive in the past. It’s especially good to see it applied to jQuery – a technology that has stood in drastic contrast to Microsoft’s own internal efforts in terms of design, usage model and… popularity. It’s great to see that Microsoft is paying attention to what customers prefer to use and supporting the customer sentiment – even if it meant drastically changing course of policy and moving into a more open and sharing environment in the process. The additional jQuery support that has been introduced in the last two years certainly has made lives easier for many developers on the ASP.NET platform. It’s also nice to see Microsoft submitting proposals through the standard jQuery process of plug-ins and getting accepted for various very useful projects. Certainly the jQuery Templates plug-in is going to be very useful to many especially since it will be baked into the jQuery core in jQuery 1.5. I hope we see more of this type of involvement from Microsoft in the future. Kudos!© Rick Strahl, West Wind Technologies, 2005-2010Posted in jQuery  ASP.NET  

  Read the article

• ASP.NET MVC 3 Hosting :: New Features in ASP.NET MVC 3

  - by mbridge

  Razor View Engine The Razor view engine is a new view engine option for ASP.NET MVC that supports the Razor templating syntax. The Razor syntax is a streamlined approach to HTML templating designed with the goal of being a code driven minimalist templating approach that builds on existing C#, VB.NET and HTML knowledge. The result of this approach is that Razor views are very lean and do not contain unnecessary constructs that get in the way of you and your code. ASP.NET MVC 3 Preview 1 only supports C# Razor views which use the .cshtml file extension. VB.NET support will be enabled in later releases of ASP.NET MVC 3. For more information and examples, see Introducing “Razor” – a new view engine for ASP.NET on Scott Guthrie’s blog. Dynamic View and ViewModel Properties A new dynamic View property is available in views, which provides access to the ViewData object using a simpler syntax. For example, imagine two items are added to the ViewData dictionary in the Index controller action using code like the following: public ActionResult Index() {          ViewData["Title"] = "The Title";          ViewData["Message"] = "Hello World!"; } Those properties can be accessed in the Index view using code like this: <h2>View.Title</h2> <p>View.Message</p> There is also a new dynamic ViewModel property in the Controller class that lets you add items to the ViewData dictionary using a simpler syntax. Using the previous controller example, the two values added to the ViewData dictionary can be rewritten using the following code: public ActionResult Index() {     ViewModel.Title = "The Title";     ViewModel.Message = "Hello World!"; } “Add View” Dialog Box Supports Multiple View Engines The Add View dialog box in Visual Studio includes extensibility hooks that allow it to support multiple view engines, as shown in the following figure: Service Location and Dependency Injection Support ASP.NET MVC 3 introduces improved support for applying Dependency Injection (DI) via Inversion of Control (IoC) containers. ASP.NET MVC 3 Preview 1 provides the following hooks for locating services and injecting dependencies: - Creating controller factories. - Creating controllers and setting dependencies. - Setting dependencies on view pages for both the Web Form view engine and the Razor view engine (for types that derive from ViewPage, ViewUserControl, ViewMasterPage, WebViewPage). - Setting dependencies on action filters. Using a Dependency Injection container is not required in order for ASP.NET MVC 3 to function properly. Global Filters ASP.NET MVC 3 allows you to register filters that apply globally to all controller action methods. Adding a filter to the global filters collection ensures that the filter runs for all controller requests. To register an action filter globally, you can make the following call in the Application_Start method in the Global.asax file: GlobalFilters.Filters.Add(new MyActionFilter()); The source of global action filters is abstracted by the new IFilterProvider interface, which can be registered manually or by using Dependency Injection. This allows you to provide your own source of action filters and choose at run time whether to apply a filter to an action in a particular request. New JsonValueProviderFactory Class The new JsonValueProviderFactory class allows action methods to receive JSON-encoded data and model-bind it to an action-method parameter. This is useful in scenarios such as client templating. Client templates enable you to format and display a single data item or set of data items by using a fragment of HTML. ASP.NET MVC 3 lets you connect client templates easily with an action method that both returns and receives JSON data. Support for .NET Framework 4 Validation Attributes and IvalidatableObject The ValidationAttribute class was improved in the .NET Framework 4 to enable richer support for validation. When you write a custom validation attribute, you can use a new IsValid overload that provides a ValidationContext instance. This instance provides information about the current validation context, such as what object is being validated. This change enables scenarios such as validating the current value based on another property of the model. The following example shows a sample custom attribute that ensures that the value of PropertyOne is always larger than the value of PropertyTwo: public class CompareValidationAttribute : ValidationAttribute {     protected override ValidationResult IsValid(object value,              ValidationContext validationContext) {         var model = validationContext.ObjectInstance as SomeModel;         if (model.PropertyOne > model.PropertyTwo) {            return ValidationResult.Success;         }         return new ValidationResult("PropertyOne must be larger than PropertyTwo");     } } Validation in ASP.NET MVC also supports the .NET Framework 4 IValidatableObject interface. This interface allows your model to perform model-level validation, as in the following example: public class SomeModel : IValidatableObject {     public int PropertyOne { get; set; }     public int PropertyTwo { get; set; }     public IEnumerable<ValidationResult> Validate(ValidationContext validationContext) {         if (PropertyOne <= PropertyTwo) {            yield return new ValidationResult(                "PropertyOne must be larger than PropertyTwo");         }     } } New IClientValidatable Interface The new IClientValidatable interface allows the validation framework to discover at run time whether a validator has support for client validation. This interface is designed to be independent of the underlying implementation; therefore, where you implement the interface depends on the validation framework in use. For example, for the default data annotations-based validator, the interface would be applied on the validation attribute. Support for .NET Framework 4 Metadata Attributes ASP.NET MVC 3 now supports .NET Framework 4 metadata attributes such as DisplayAttribute. New IMetadataAware Interface The new IMetadataAware interface allows you to write attributes that simplify how you can contribute to the ModelMetadata creation process. Before this interface was available, you needed to write a custom metadata provider in order to have an attribute provide extra metadata. This interface is consumed by the AssociatedMetadataProvider class, so support for the IMetadataAware interface is automatically inherited by all classes that derive from that class (notably, the DataAnnotationsModelMetadataProvider class). New Action Result Types In ASP.NET MVC 3, the Controller class includes two new action result types and corresponding helper methods. HttpNotFoundResult Action The new HttpNotFoundResult action result is used to indicate that a resource requested by the current URL was not found. The status code is 404. This class derives from HttpStatusCodeResult. The Controller class includes an HttpNotFound method that returns an instance of this action result type, as shown in the following example: public ActionResult List(int id) {     if (id < 0) {                 return HttpNotFound();     }     return View(); } HttpStatusCodeResult Action The new HttpStatusCodeResult action result is used to set the response status code and description. Permanent Redirect The HttpRedirectResult class has a new Boolean Permanent property that is used to indicate whether a permanent redirect should occur. A permanent redirect uses the HTTP 301 status code. Corresponding to this change, the Controller class now has several methods for performing permanent redirects: - RedirectPermanent - RedirectToRoutePermanent - RedirectToActionPermanent These methods return an instance of HttpRedirectResult with the Permanent property set to true. Breaking Changes The order of execution for exception filters has changed for exception filters that have the same Order value. In ASP.NET MVC 2 and earlier, exception filters on the controller with the same Order as those on an action method were executed before the exception filters on the action method. This would typically be the case when exception filters were applied without a specified order Order value. In MVC 3, this order has been reversed in order to allow the most specific exception handler to execute first. As in earlier versions, if the Order property is explicitly specified, the filters are run in the specified order. Known Issues When you are editing a Razor view (CSHTML file), the Go To Controller menu item in Visual Studio will not be available, and there are no code snippets.

  Read the article

• Rapid Repository – Silverlight Development

  - by SeanMcAlinden

  Hi All, One of the questions I was recently asked was whether the Rapid Repository would work for normal Silverlight development as well as for the Windows 7 Phone. I can confirm that the current code in the trunk will definitely work for both the Windows 7 Phone and normal Silverlight development. I haven’t tested V.1.0 for compatibility but V2.0 which will be released fairly soon will work absolutely fine.   Kind Regards, Sean McAlinden.

  Read the article

• Building a StackOverflow inspired Knowledge Exchange Three Tiers to MVC – Hooray – Dependency Inject

  In this article we will address the lack of testability that our current application has. We will do this by making our application conform to the dependency injection pattern. This will allow us to push up all of our dependencies which makes our code considerably more testable than it currently is.

  Read the article

• AutoMapper MappingFunction from Source Type of NameValueCollection

  - by REA_ANDREW

  I have had a situation arise today where I need to construct a complex type from a source of a NameValueCollection.  A little while back I submitted a patch for the Agatha Project to include REST (JSON and XML) support for the service contract.  I realized today that as useful as it is, it did not actually support true REST conformance, as REST should support GET so that you can use JSONP from JavaScript directly meaning you can query cross domain services.  My original implementation for POX and JSON used the POST method and this immediately rules out JSONP as from reading, JSONP only works with GET Requests. This then raised another issue.  The current operation contract of Agatha and one of its main benefits is that you can supply an array of Request objects in a single request, limiting the about of server requests you need to make.  Now, at the present time I am thinking that this will not be the case for the REST imlementation but will yield the benefits of the fact that : The same Request objects can be used for SOAP and RST (POX, JSON) The construct of the JavaScript functions will be simpler and more readable It will enable the use of JSONP for cross domain REST Services The current contract for the Agatha WcfRequestProcessor is at time of writing the following: [ServiceContract] public interface IWcfRequestProcessor { [OperationContract(Name = "ProcessRequests")] [ServiceKnownType("GetKnownTypes", typeof(KnownTypeProvider))] [TransactionFlow(TransactionFlowOption.Allowed)] Response[] Process(params Request[] requests); [OperationContract(Name = "ProcessOneWayRequests", IsOneWay = true)] [ServiceKnownType("GetKnownTypes", typeof(KnownTypeProvider))] void ProcessOneWayRequests(params OneWayRequest[] requests); }   My current proposed solution, and at the very early stages of my concept is as follows: [ServiceContract] public interface IWcfRestJsonRequestProcessor { [OperationContract(Name="process")] [ServiceKnownType("GetKnownTypes", typeof(KnownTypeProvider))] [TransactionFlow(TransactionFlowOption.Allowed)] [WebGet(UriTemplate = "process/{name}/{*parameters}", BodyStyle = WebMessageBodyStyle.WrappedResponse, ResponseFormat = WebMessageFormat.Json)] Response[] Process(string name, NameValueCollection parameters); [OperationContract(Name="processoneway",IsOneWay = true)] [ServiceKnownType("GetKnownTypes", typeof(KnownTypeProvider))] [WebGet(UriTemplate = "process-one-way/{name}/{*parameters}", BodyStyle = WebMessageBodyStyle.WrappedResponse, ResponseFormat = WebMessageFormat.Json)] void ProcessOneWayRequests(string name, NameValueCollection parameters); }   Now this part I have not yet implemented, it is the preliminart step which I have developed which will allow me to take the name of the Request Type and the NameValueCollection and construct the complex type which is that of the Request which I can then supply to a nested instance of the original IWcfRequestProcessor  and work as it should normally.  To give an example of some of the urls which you I envisage with this method are: http://www.url.com/service.svc/json/process/getweather/?location=london http://www.url.com/service.svc/json/process/getproductsbycategory/?categoryid=1 http://www.url.om/service.svc/json/process/sayhello/?name=andy Another reason why my direction has gone to a single request for the REST implementation is because of restrictions which are imposed by browsers on the length of the url.  From what I have read this is on average 2000 characters.  I think that this is a very acceptable usage limit in the context of using 1 request, but I do not think this is acceptable for accommodating multiple requests chained together.  I would love to be corrected on that one, I really would but unfortunately from what I have read I have come to the conclusion that this is not the case. The mapping function So, as I say this is just the first pass I have made at this, and I am not overly happy with the try catch for detecting types without default constructors.  I know there is a better way but for the minute, it escapes me.  I would also like to know the correct way for adding mapping functions and not using the anonymous way that I have used.  To achieve this I have used recursion which I am sure is what other mapping function use. As you do have to go as deep as the complex type is. public static object RecurseType(NameValueCollection collection, Type type, string prefix) { try { var returnObject = Activator.CreateInstance(type); foreach (var property in type.GetProperties()) { foreach (var key in collection.AllKeys) { if (String.IsNullOrEmpty(prefix) || key.Length > prefix.Length) { var propertyNameToMatch = String.IsNullOrEmpty(prefix) ? key : key.Substring(property.Name.IndexOf(prefix) + prefix.Length + 1); if (property.Name == propertyNameToMatch) { property.SetValue(returnObject, Convert.ChangeType(collection.Get(key), property.PropertyType), null); } else if(property.GetValue(returnObject,null) == null) { property.SetValue(returnObject, RecurseType(collection, property.PropertyType, String.Concat(prefix, property.PropertyType.Name)), null); } } } } return returnObject; } catch (MissingMethodException) { //Quite a blunt way of dealing with Types without default constructor return null; } }   Another thing is performance, I have not measured this in anyway, it is as I say the first pass, so I hope this can be the start of a more perfected implementation.  I tested this out with a complex type of three levels, there is no intended logical meaning to the properties, they are simply for the purposes of example.  You could call this a spiking session, as from here on in, now I know what I am building I would take a more TDD approach.  OK, purists, why did I not do this from the start, well I didn’t, this was a brain dump and now I know what I am building I can. The console test and how I used with AutoMapper is as follows: static void Main(string[] args) { var collection = new NameValueCollection(); collection.Add("Name", "Andrew Rea"); collection.Add("Number", "1"); collection.Add("AddressLine1", "123 Street"); collection.Add("AddressNumber", "2"); collection.Add("AddressPostCodeCountry", "United Kingdom"); collection.Add("AddressPostCodeNumber", "3"); AutoMapper.Mapper.CreateMap<NameValueCollection, Person>() .ConvertUsing(x => { return(Person) RecurseType(x, typeof(Person), null); }); var person = AutoMapper.Mapper.Map<NameValueCollection, Person>(collection); Console.WriteLine(person.Name); Console.WriteLine(person.Number); Console.WriteLine(person.Address.Line1); Console.WriteLine(person.Address.Number); Console.WriteLine(person.Address.PostCode.Country); Console.WriteLine(person.Address.PostCode.Number); Console.ReadLine(); }   Notice the convention that I am using and that this method requires you do use.  Each property is prefixed with the constructed name of its parents combined.  This is the convention used by AutoMapper and it makes sense. I can also think of other uses for this including using with ASP.NET MVC ModelBinders for creating a complex type from the QueryString which is itself is a NameValueCollection. Hope this is of some help to people and I would welcome any code reviews you could give me. References: Agatha : http://code.google.com/p/agatha-rrsl/ AutoMapper : http://automapper.codeplex.com/   Cheers for now, Andrew   P.S. I will have the proposed solution for a more complete REST implementation for AGATHA very soon. 

  Read the article

• Building a StackOverflow inspired Knowledge Exchange Three Tiers to MVC – Distributed systems: addin

  In this article we are going to look at how distributable our current code base is. We will find that even with all the refactoring and modifications that we have done we are still pretty married to a fairly hardwired infrastructure. If one piece of our code requires more resources than any other we can’t simply scale out that bit. Presented By: NEC   Ads by Pheedo

  Read the article

• Intellitrace bug causes &ldquo;Operation could destabilize the runtime&rdquo; exception

  - by Magnus Karlsson

  We cant use it when we use simplemembership to handle external authorizations.   Server Error in '/' Application. Operation could destabilize the runtime. Description: An unhandled exception occurred during the execution of the current web request. Please review the stack trace for more information about the error and where it originated in the code. Exception Details: System.Security.VerificationException: Operation could destabilize the runtime. Source Error: An unhandled exception was generated during the execution of the current web request. Information regarding the origin and location of the exception can be identified using the exception stack trace below. Stack Trace: [VerificationException: Operation could destabilize the runtime.] DotNetOpenAuth.OpenId.Messages.IndirectSignedResponse.GetSignedMessageParts(Channel channel) +943 DotNetOpenAuth.OpenId.ChannelElements.ExtensionsBindingElement.GetExtensionsDictionary(IProtocolMessage message, Boolean ignoreUnsigned) +282 DotNetOpenAuth.OpenId.ChannelElements.<GetExtensions>d__a.MoveNext() +279 DotNetOpenAuth.OpenId.ChannelElements.ExtensionsBindingElement.ProcessIncomingMessage(IProtocolMessage message) +594 DotNetOpenAuth.Messaging.Channel.ProcessIncomingMessage(IProtocolMessage message) +933 DotNetOpenAuth.OpenId.ChannelElements.OpenIdChannel.ProcessIncomingMessage(IProtocolMessage message) +326 DotNetOpenAuth.Messaging.Channel.ReadFromRequest(HttpRequestBase httpRequest) +1343 DotNetOpenAuth.OpenId.RelyingParty.OpenIdRelyingParty.GetResponse(HttpRequestBase httpRequestInfo) +241 DotNetOpenAuth.OpenId.RelyingParty.OpenIdRelyingParty.GetResponse() +361 DotNetOpenAuth.AspNet.Clients.OpenIdClient.VerifyAuthentication(HttpContextBase context) +136 DotNetOpenAuth.AspNet.OpenAuthSecurityManager.VerifyAuthentication(String returnUrl) +984 Microsoft.Web.WebPages.OAuth.OAuthWebSecurity.VerifyAuthenticationCore(HttpContextBase context, String returnUrl) +333 Microsoft.Web.WebPages.OAuth.OAuthWebSecurity.VerifyAuthentication(String returnUrl) +192 PrioMvcWebRole.Controllers.AccountController.ExternalLoginCallback(String returnUrl) in c:hiddenforyou lambda_method(Closure , ControllerBase , Object[] ) +127 System.Web.Mvc.ReflectedActionDescriptor.Execute(ControllerContext controllerContext, IDictionary`2 parameters) +250 System.Web.Mvc.ControllerActionInvoker.InvokeActionMethod(ControllerContext controllerContext, ActionDescriptor actionDescriptor, IDictionary`2 parameters) +39 System.Web.Mvc.Async.<>c__DisplayClass39.<BeginInvokeActionMethodWithFilters>b__33() +87 System.Web.Mvc.Async.<>c__DisplayClass4f.<InvokeActionMethodFilterAsynchronously>b__49() +439 System.Web.Mvc.Async.<>c__DisplayClass4f.<InvokeActionMethodFilterAsynchronously>b__49() +439 System.Web.Mvc.Async.<>c__DisplayClass37.<BeginInvokeActionMethodWithFilters>b__36(IAsyncResult asyncResult) +15 System.Web.Mvc.Async.<>c__DisplayClass2a.<BeginInvokeAction>b__20() +34 System.Web.Mvc.Async.<>c__DisplayClass25.<BeginInvokeAction>b__22(IAsyncResult asyncResult) +221 System.Web.Mvc.<>c__DisplayClass1d.<BeginExecuteCore>b__18(IAsyncResult asyncResult) +28 System.Web.Mvc.Async.<>c__DisplayClass4.<MakeVoidDelegate>b__3(IAsyncResult ar) +15 System.Web.Mvc.Controller.EndExecuteCore(IAsyncResult asyncResult) +42 System.Web.Mvc.Async.<>c__DisplayClass4.<MakeVoidDelegate>b__3(IAsyncResult ar) +15 System.Web.Mvc.<>c__DisplayClass8.<BeginProcessRequest>b__3(IAsyncResult asyncResult) +42 System.Web.Mvc.Async.<>c__DisplayClass4.<MakeVoidDelegate>b__3(IAsyncResult ar) +15 System.Web.CallHandlerExecutionStep.System.Web.HttpApplication.IExecutionStep.Execute() +523 System.Web.HttpApplication.ExecuteStep(IExecutionStep step, Boolean& completedSynchronously) +176 Version Information: Microsoft .NET Framework Version:4.0.30319; ASP.NET Version:4.0.30319.17929

  Read the article

• Enterprise Library Logging / Exception handling and Postsharp

  - by subodhnpushpak

  One of my colleagues came-up with a unique situation where it was required to create log files based on the input file which is uploaded. For example if A.xml is uploaded, the corresponding log file should be A_log.txt. I am a strong believer that Logging / EH / caching are cross-cutting architecture aspects and should be least invasive to the business-logic written in enterprise application. I have been using Enterprise Library for logging / EH (i use to work with Avanade, so i have affection towards the library!! :D ). I have been also using excellent library called PostSharp for cross cutting aspect. Here i present a solution with and without PostSharp all in a unit test. Please see full source code at end of the this blog post. But first, we need to tweak the enterprise library so that the log files are created at runtime based on input given. Below is Custom trace listner which writes log into a given file extracted out of Logentry extendedProperties property. using Microsoft.Practices.EnterpriseLibrary.Common.Configuration; using Microsoft.Practices.EnterpriseLibrary.Logging.Configuration; using Microsoft.Practices.EnterpriseLibrary.Logging.TraceListeners; using Microsoft.Practices.EnterpriseLibrary.Logging; using System.IO; using System.Text; using System; using System.Diagnostics;   namespace Subodh.Framework.Logging { [ConfigurationElementType(typeof(CustomTraceListenerData))] public class LogToFileTraceListener : CustomTraceListener {   private static object syncRoot = new object();   public override void TraceData(TraceEventCache eventCache, string source, TraceEventType eventType, int id, object data) {   if ((data is LogEntry) & this.Formatter != null) { WriteOutToLog(this.Formatter.Format((LogEntry)data), (LogEntry)data); } else { WriteOutToLog(data.ToString(), (LogEntry)data); } }   public override void Write(string message) { Debug.Print(message.ToString()); }   public override void WriteLine(string message) { Debug.Print(message.ToString()); }   private void WriteOutToLog(string BodyText, LogEntry logentry) { try { //Get the filelocation from the extended properties if (logentry.ExtendedProperties.ContainsKey("filelocation")) { string fullPath = Path.GetFullPath(logentry.ExtendedProperties["filelocation"].ToString());   //Create the directory where the log file is written to if it does not exist. DirectoryInfo directoryInfo = new DirectoryInfo(Path.GetDirectoryName(fullPath));   if (directoryInfo.Exists == false) { directoryInfo.Create(); }   //Lock the file to prevent another process from using this file //as data is being written to it.   lock (syncRoot) { using (FileStream fs = new FileStream(fullPath, FileMode.Append, FileAccess.Write, FileShare.Write, 4096, true)) { using (StreamWriter sw = new StreamWriter(fs, Encoding.UTF8)) { Log(BodyText, sw); sw.Close(); } fs.Close(); } } } } catch (Exception ex) { throw new LoggingException(ex.Message, ex); } }   /// <summary> /// Write message to named file /// </summary> public static void Log(string logMessage, TextWriter w) { w.WriteLine("{0}", logMessage); } } }   The above can be “plugged into” the code using below configuration <loggingConfiguration name="Logging Application Block" tracingEnabled="true" defaultCategory="Trace" logWarningsWhenNoCategoriesMatch="true"> <listeners> <add listenerDataType="Microsoft.Practices.EnterpriseLibrary.Logging.Configuration.CustomTraceListenerData, Microsoft.Practices.EnterpriseLibrary.Logging, Version=4.1.0.0, Culture=neutral, PublicKeyToken=31bf3856ad364e35" traceOutputOptions="None" filter="All" type="Subodh.Framework.Logging.LogToFileTraceListener, Subodh.Framework.Logging, Version=1.0.0.0, Culture=neutral, PublicKeyToken=null" name="Subodh Custom Trace Listener" initializeData="" formatter="Text Formatter" /> </listeners> Similarly we can use PostSharp to expose the above as cross cutting aspects as below using System; using System.Collections.Generic; using System.Linq; using System.Text; using System.Reflection; using PostSharp.Laos; using System.Diagnostics; using GC.FrameworkServices.ExceptionHandler; using Subodh.Framework.Logging;   namespace Subodh.Framework.ExceptionHandling { [Serializable] public sealed class LogExceptionAttribute : OnExceptionAspect { private string prefix; private MethodFormatStrings formatStrings;   // This field is not serialized. It is used only at compile time. [NonSerialized] private readonly Type exceptionType; private string fileName;   /// <summary> /// Declares a <see cref="XTraceExceptionAttribute"/> custom attribute /// that logs every exception flowing out of the methods to which /// the custom attribute is applied. /// </summary> public LogExceptionAttribute() { }   /// <summary> /// Declares a <see cref="XTraceExceptionAttribute"/> custom attribute /// that logs every exception derived from a given <see cref="Type"/> /// flowing out of the methods to which /// the custom attribute is applied. /// </summary> /// <param name="exceptionType"></param> public LogExceptionAttribute( Type exceptionType ) { this.exceptionType = exceptionType; }   public LogExceptionAttribute(Type exceptionType, string fileName) { this.exceptionType = exceptionType; this.fileName = fileName; }   /// <summary> /// Gets or sets the prefix string, printed before every trace message. /// </summary> /// <value> /// For instance <c>[Exception]</c>. /// </value> public string Prefix { get { return this.prefix; } set { this.prefix = value; } }   /// <summary> /// Initializes the current object. Called at compile time by PostSharp. /// </summary> /// <param name="method">Method to which the current instance is /// associated.</param> public override void CompileTimeInitialize( MethodBase method ) { // We just initialize our fields. They will be serialized at compile-time // and deserialized at runtime. this.formatStrings = Formatter.GetMethodFormatStrings( method ); this.prefix = Formatter.NormalizePrefix( this.prefix ); }   public override Type GetExceptionType( MethodBase method ) { return this.exceptionType; }   /// <summary> /// Method executed when an exception occurs in the methods to which the current /// custom attribute has been applied. We just write a record to the tracing /// subsystem. /// </summary> /// <param name="context">Event arguments specifying which method /// is being called and with which parameters.</param> public override void OnException( MethodExecutionEventArgs context ) { string message = String.Format("{0}Exception {1} {{{2}}} in {{{3}}}. \r\n\r\nStack Trace {4}", this.prefix, context.Exception.GetType().Name, context.Exception.Message, this.formatStrings.Format(context.Instance, context.Method, context.GetReadOnlyArgumentArray()), context.Exception.StackTrace); if(!string.IsNullOrEmpty(fileName)) { ApplicationLogger.LogException(message, fileName); } else { ApplicationLogger.LogException(message, Source.UtilityService); } } } } To use the above below is the unit test [TestMethod] [ExpectedException(typeof(NotImplementedException))] public void TestMethod1() { MethodThrowingExceptionForLog(); try { MethodThrowingExceptionForLogWithPostSharp(); } catch (NotImplementedException ex) { throw ex; } }   private void MethodThrowingExceptionForLog() { try { throw new NotImplementedException(); } catch (NotImplementedException ex) { // create file and then write log ApplicationLogger.TraceMessage("this is a trace message which will be logged in Test1MyFile", @"D:\EL\Test1Myfile.txt"); ApplicationLogger.TraceMessage("this is a trace message which will be logged in YetAnotherTest1Myfile", @"D:\EL\YetAnotherTest1Myfile.txt"); } }   // Automatically log details using attributes // Log exception using attributes .... A La WCF [FaultContract(typeof(FaultMessage))] style] [Log(@"D:\EL\Test1MyfileLogPostsharp.txt")] [LogException(typeof(NotImplementedException), @"D:\EL\Test1MyfileExceptionPostsharp.txt")] private void MethodThrowingExceptionForLogWithPostSharp() { throw new NotImplementedException(); } The good thing about the approach is that all the logging and EH is done at centralized location controlled by PostSharp. Of Course, if some other library has to be used instead of EL, it can easily be plugged in. Also, the coder ARE ONLY involved in writing business code in methods, which makes code cleaner. Here is the full source code. The third party assemblies provided are from EL and PostSharp and i presume you will find these useful. Do let me know your thoughts / ideas on the same. Technorati Tags: PostSharp,Enterprize library,C#,Logging,Exception handling

  Read the article

• How I use PowerShell to collect Performance Counter data

  - by AaronBertrand

  In a current project, I need to collect performance counters from a set of virtual machines that are performing different tasks and running a variety of workloads. In a similar project last year, I used LogMan to collect performance data. This time I decided to try PowerShell because, well, all the kids are doing it, I felt a little passé, and a lot of the other tasks in this project (such as building out VMs and running workloads) were already being accomplished via PowerShell. And after all, I...(read more)

  Read the article

• Stuck at the STARTUP [closed]

  - by Tarik Setia

  I started with "Getting started with asp mvc4 tutorial". I just created the project and when I pressed F5 I got this: Server Error in '/' Application. -------------------------------------------------------------------------------- Could not load type 'System.Web.WebPages.DisplayModes' from assembly 'System.Web.WebPages, Version=2.0.0.0, Culture=neutral, PublicKeyToken=31bf3856ad364e35'. Description: An unhandled exception occurred during the execution of the current web request. Please review the stack trace for more information about the error and where it originated in the code. Exception Details: System.TypeLoadException: Could not load type 'System.Web.WebPages.DisplayModes' from assembly 'System.Web.WebPages, Version=2.0.0.0, Culture=neutral, PublicKeyToken=31bf3856ad364e35'. Source Error: An unhandled exception was generated during the execution of the current web request. Information regarding the origin and location of the exception can be identified using the exception stack trace below. Stack Trace: [TypeLoadException: Could not load type 'System.Web.WebPages.DisplayModes' from assembly 'System.Web.WebPages, Version=2.0.0.0, Culture=neutral, PublicKeyToken=31bf3856ad364e35'.] System.Web.Mvc.VirtualPathProviderViewEngine.GetPath(ControllerContext controllerContext, String[] locations, String[] areaLocations, String locationsPropertyName, String name, String controllerName, String cacheKeyPrefix, Boolean useCache, String[]& searchedLocations) +0 System.Web.Mvc.VirtualPathProviderViewEngine.FindView(ControllerContext controllerContext, String viewName, String masterName, Boolean useCache) +315 System.Web.Mvc.c__DisplayClassc.b__a(IViewEngine e) +68 System.Web.Mvc.ViewEngineCollection.Find(Func`2 lookup, Boolean trackSearchedPaths) +182 System.Web.Mvc.ViewEngineCollection.Find(Func`2 cacheLocator, Func`2 locator) +67 System.Web.Mvc.ViewEngineCollection.FindView(ControllerContext controllerContext, String viewName, String masterName) +329 System.Web.Mvc.ViewResult.FindView(ControllerContext context) +135 System.Web.Mvc.ViewResultBase.ExecuteResult(ControllerContext context) +230 System.Web.Mvc.ControllerActionInvoker.InvokeActionResult(ControllerContext controllerContext, ActionResult actionResult) +39 System.Web.Mvc.c__DisplayClass1c.b__19() +74 System.Web.Mvc.ControllerActionInvoker.InvokeActionResultFilter(IResultFilter filter, ResultExecutingContext preContext, Func`1 continuation) +388 System.Web.Mvc.c__DisplayClass1e.b__1b() +72 System.Web.Mvc.ControllerActionInvoker.InvokeActionResultWithFilters(ControllerContext controllerContext, IList`1 filters, ActionResult actionResult) +303 System.Web.Mvc.ControllerActionInvoker.InvokeAction(ControllerContext controllerContext, String actionName) +844 System.Web.Mvc.Controller.ExecuteCore() +130 System.Web.Mvc.ControllerBase.Execute(RequestContext requestContext) +229 System.Web.Mvc.ControllerBase.System.Web.Mvc.IController.Execute(RequestContext requestContext) +39 System.Web.Mvc.c__DisplayClassb.b__5() +71 System.Web.Mvc.Async.c__DisplayClass1.b__0() +44 System.Web.Mvc.Async.c__DisplayClass8`1.b__7(IAsyncResult _) +42 System.Web.Mvc.Async.WrappedAsyncResult`1.End() +152 System.Web.Mvc.Async.AsyncResultWrapper.End(IAsyncResult asyncResult, Object tag) +59 System.Web.Mvc.Async.AsyncResultWrapper.End(IAsyncResult asyncResult, Object tag) +40 System.Web.Mvc.c__DisplayClasse.b__d() +75 System.Web.Mvc.SecurityUtil.b__0(Action f) +31 System.Web.Mvc.SecurityUtil.ProcessInApplicationTrust(Action action) +61 System.Web.Mvc.MvcHandler.EndProcessRequest(IAsyncResult asyncResult) +118 System.Web.Mvc.MvcHandler.System.Web.IHttpAsyncHandler.EndProcessRequest(IAsyncResult result) +38 System.Web.CallHandlerExecutionStep.System.Web.HttpApplication.IExecutionStep.Execute() +10303829 System.Web.HttpApplication.ExecuteStep(IExecutionStep step, Boolean& completedSynchronously) +178 -------------------------------------------------------------------------------- Version Information: Microsoft .NET Framework Version:4.0.30319; ASP.NET Version:4.0.30319.17020

  Read the article

• Using dnnModal.show in your modules and content

  - by Chris Hammond

  One thing that was added in DotNetNuke 6 but hasn’t been covered in great detail is a method called dnnModal.show. Calling this method is fairly straight forward depending on your need, but before we get into how to call/use the method, let’s talk about what it does first. dnnModal.show is a method that gets called via JavaScript and allows you to load up a URL into a modal popup window within your DotNetNuke site. Basically it will take that URL and load it into an IFrame within the current DotNetNuke...(read more)

  Read the article

• How I use PowerShell to collect Performance Counter data

  - by AaronBertrand

  In a current project, I need to collect performance counters from a set of virtual machines that are performing different tasks and running a variety of workloads. In a similar project last year, I used LogMan to collect performance data. This time I decided to try PowerShell because, well, all the kids are doing it, I felt a little passé, and a lot of the other tasks in this project (such as building out VMs and running workloads) were already being accomplished via PowerShell. And after all, I...(read more)

  Read the article

• Maintaining shared service in ASP.NET MVC Application

  - by kazimanzurrashid

  Depending on the application sometimes we have to maintain some shared service throughout our application. Let’s say you are developing a multi-blog supported blog engine where both the controller and view must know the currently visiting blog, it’s setting , user information and url generation service. In this post, I will show you how you can handle this kind of case in most convenient way. First, let see the most basic way, we can create our PostController in the following way: public class PostController : Controller { public PostController(dependencies...) { } public ActionResult Index(string blogName, int? page) { BlogInfo blog = blogSerivce.FindByName(blogName); if (blog == null) { return new NotFoundResult(); } IEnumerable<PostInfo> posts = postService.FindPublished(blog.Id, PagingCalculator.StartIndex(page, blog.PostPerPage), blog.PostPerPage); int count = postService.GetPublishedCount(blog.Id); UserInfo user = null; if (HttpContext.User.Identity.IsAuthenticated) { user = userService.FindByName(HttpContext.User.Identity.Name); } return View(new IndexViewModel(urlResolver, user, blog, posts, count, page)); } public ActionResult Archive(string blogName, int? page, ArchiveDate archiveDate) { BlogInfo blog = blogSerivce.FindByName(blogName); if (blog == null) { return new NotFoundResult(); } IEnumerable<PostInfo> posts = postService.FindArchived(blog.Id, archiveDate, PagingCalculator.StartIndex(page, blog.PostPerPage), blog.PostPerPage); int count = postService.GetArchivedCount(blog.Id, archiveDate); UserInfo user = null; if (HttpContext.User.Identity.IsAuthenticated) { user = userService.FindByName(HttpContext.User.Identity.Name); } return View(new ArchiveViewModel(urlResolver, user, blog, posts, count, page, achiveDate)); } public ActionResult Tag(string blogName, string tagSlug, int? page) { BlogInfo blog = blogSerivce.FindByName(blogName); if (blog == null) { return new NotFoundResult(); } TagInfo tag = tagService.FindBySlug(blog.Id, tagSlug); if (tag == null) { return new NotFoundResult(); } IEnumerable<PostInfo> posts = postService.FindPublishedByTag(blog.Id, tag.Id, PagingCalculator.StartIndex(page, blog.PostPerPage), blog.PostPerPage); int count = postService.GetPublishedCountByTag(tag.Id); UserInfo user = null; if (HttpContext.User.Identity.IsAuthenticated) { user = userService.FindByName(HttpContext.User.Identity.Name); } return View(new TagViewModel(urlResolver, user, blog, posts, count, page, tag)); } } As you can see the above code heavily depends upon the current blog and the blog retrieval code is duplicated in all of the action methods, once the blog is retrieved the same blog is passed in the view model. Other than the blog the view also needs the current user and url resolver to render it properly. One way to remove the duplicate blog retrieval code is to create a custom model binder which converts the blog from a blog name and use the blog a parameter in the action methods instead of the string blog name, but it only helps the first half in the above scenario, the action methods still have to pass the blog, user and url resolver etc in the view model. Now lets try to improve the the above code, first lets create a new class which would contain the shared services, lets name it as BlogContext: public class BlogContext { public BlogInfo Blog { get; set; } public UserInfo User { get; set; } public IUrlResolver UrlResolver { get; set; } } Next, we will create an interface, IContextAwareService: public interface IContextAwareService { BlogContext Context { get; set; } } The idea is, whoever needs these shared services needs to implement this interface, in our case both the controller and the view model, now we will create an action filter which will be responsible for populating the context: public class PopulateBlogContextAttribute : FilterAttribute, IActionFilter { private static string blogNameRouteParameter = "blogName"; private readonly IBlogService blogService; private readonly IUserService userService; private readonly BlogContext context; public PopulateBlogContextAttribute(IBlogService blogService, IUserService userService, IUrlResolver urlResolver) { Invariant.IsNotNull(blogService, "blogService"); Invariant.IsNotNull(userService, "userService"); Invariant.IsNotNull(urlResolver, "urlResolver"); this.blogService = blogService; this.userService = userService; context = new BlogContext { UrlResolver = urlResolver }; } public static string BlogNameRouteParameter { [DebuggerStepThrough] get { return blogNameRouteParameter; } [DebuggerStepThrough] set { blogNameRouteParameter = value; } } public void OnActionExecuting(ActionExecutingContext filterContext) { string blogName = (string) filterContext.Controller.ValueProvider.GetValue(BlogNameRouteParameter).ConvertTo(typeof(string), Culture.Current); if (!string.IsNullOrWhiteSpace(blogName)) { context.Blog = blogService.FindByName(blogName); } if (context.Blog == null) { filterContext.Result = new NotFoundResult(); return; } if (filterContext.HttpContext.User.Identity.IsAuthenticated) { context.User = userService.FindByName(filterContext.HttpContext.User.Identity.Name); } IContextAwareService controller = filterContext.Controller as IContextAwareService; if (controller != null) { controller.Context = context; } } public void OnActionExecuted(ActionExecutedContext filterContext) { Invariant.IsNotNull(filterContext, "filterContext"); if ((filterContext.Exception == null) || filterContext.ExceptionHandled) { IContextAwareService model = filterContext.Controller.ViewData.Model as IContextAwareService; if (model != null) { model.Context = context; } } } } As you can see we are populating the context in the OnActionExecuting, which executes just before the controllers action methods executes, so by the time our action methods executes the context is already populated, next we are are assigning the same context in the view model in OnActionExecuted method which executes just after we set the  model and return the view in our action methods. Now, lets change the view models so that it implements this interface: public class IndexViewModel : IContextAwareService { // More Codes } public class ArchiveViewModel : IContextAwareService { // More Codes } public class TagViewModel : IContextAwareService { // More Codes } and the controller: public class PostController : Controller, IContextAwareService { public PostController(dependencies...) { } public BlogContext Context { get; set; } public ActionResult Index(int? page) { IEnumerable<PostInfo> posts = postService.FindPublished(Context.Blog.Id, PagingCalculator.StartIndex(page, Context.Blog.PostPerPage), Context.Blog.PostPerPage); int count = postService.GetPublishedCount(Context.Blog.Id); return View(new IndexViewModel(posts, count, page)); } public ActionResult Archive(int? page, ArchiveDate archiveDate) { IEnumerable<PostInfo> posts = postService.FindArchived(Context.Blog.Id, archiveDate, PagingCalculator.StartIndex(page, Context.Blog.PostPerPage), Context.Blog.PostPerPage); int count = postService.GetArchivedCount(Context.Blog.Id, archiveDate); return View(new ArchiveViewModel(posts, count, page, achiveDate)); } public ActionResult Tag(string blogName, string tagSlug, int? page) { TagInfo tag = tagService.FindBySlug(Context.Blog.Id, tagSlug); if (tag == null) { return new NotFoundResult(); } IEnumerable<PostInfo> posts = postService.FindPublishedByTag(Context.Blog.Id, tag.Id, PagingCalculator.StartIndex(page, Context.Blog.PostPerPage), Context.Blog.PostPerPage); int count = postService.GetPublishedCountByTag(tag.Id); return View(new TagViewModel(posts, count, page, tag)); } } Now, the last thing where we have to glue everything, I will be using the AspNetMvcExtensibility to register the action filter (as there is no better way to inject the dependencies in action filters). public class RegisterFilters : RegisterFiltersBase { private static readonly Type controllerType = typeof(Controller); private static readonly Type contextAwareType = typeof(IContextAwareService); protected override void Register(IFilterRegistry registry) { TypeCatalog controllers = new TypeCatalogBuilder() .Add(GetType().Assembly) .Include(type => controllerType.IsAssignableFrom(type) && contextAwareType.IsAssignableFrom(type)); registry.Register<PopulateBlogContextAttribute>(controllers); } } Thoughts and Comments?

  Read the article

• Working on WPF application Memory Profiling

  - by akjoshi

  Today, I am going to start with the task of memory profiling the WPF application, on which I am working from past few months. I have successfully done this in past, fixing a lot of memory leaks and improving the performance of WPF applications; As in past, I am hopeful of fixing some very interesting bugs and improve the application performance. I am very excited as current application is very different from the previous WPF applications I had profiled, all the previous application were pure WPF...(read more)

  Read the article

• The Importance of a Security Assessment - by Michael Terra, Oracle

  - by Darin Pendergraft

  Today's Blog was written by Michael Terra, who was the Subject Matter Expert for the recently announced Oracle Online Security Assessment. You can take the Online Assessment here: Take the Online Assessment Over the past decade, IT Security has become a recognized and respected Business discipline.  Several factors have contributed to IT Security becoming a core business and organizational enabler including, but not limited to, increased external threats and increased regulatory pressure. Security is also viewed as a key enabler for strategic corporate activities such as mergers and acquisitions.Now, the challenge for senior security professionals is to develop an ongoing dialogue within their organizations about the importance of information security and how it can impact their organization's strategic objectives/mission. The importance of conducting regular “Security Assessments” across the IT and physical infrastructure has become increasingly important. Security standards and frameworks, such as the international standard ISO 27001, are increasingly being adopted by organizations and their business partners as proof of their security posture and “Security Assessments” are a great way to ensure a continued alignment to these frameworks.Oracle offers a number of different security assessment covering a broad range of technologies. Some of these are short engagements conducted for free with our strategic customers and partners. Others are longer term paid engagements delivered by Oracle Consulting Services or one of our partners. The goal of a security assessment, (also known as a security audit or security review), is to ensure that necessary security controls are integrated into the design and implementation of a project, application or technology.  A properly completed security assessment should provide documentation outlining any security gaps that exist in an infrastructure and the associated risks for those gaps. With that knowledge, an organization can choose to either mitigate, transfer, avoid or accept the risk. One example of an Oracle offering is a Security Readiness Assessment:The Oracle Security Readiness Assessment is a practical security architecture review focused on aligning an organization’s enterprise security architecture to their business principals and strategic objectives. The service will establish a multi-phase security architecture roadmap focused on supporting new and existing business initiatives.Offering OverviewThe Security Readiness Assessment will: Define an organization’s current security posture and provide a roadmap to a desired future state architecture by mapping  security solutions to business goals Incorporate commonly accepted security architecture concepts to streamline an organization’s security vision from strategy to implementation Define the people, process and technology implications of the desired future state architecture The objective is to deliver cohesive, best practice security architectures spanning multiple domains that are unique and specific to the context of your organization. Offering DetailsThe Oracle Security Readiness Assessment is a multi-stage process with a dedicated Oracle Security team supporting your organization.  During the course of this free engagement, the team will focus on the following: Review your current business operating model and supporting IT security structures and processes Partner with your organization to establish a future state security architecture leveraging Oracle’s reference architectures, capability maps, and best practices Provide guidance and recommendations on governance practices for the rollout and adoption of your future state security architecture Create an initial business case for the adoption of the future state security architecture If you are interested in finding out more, ask your Sales Consultant or Account Manager for details.

  Read the article

• Hosting StreamInsight applications using WCF

  - by gsusx

  One of the fundamental differentiators of Microsoft's StreamInsight compared to other Complex Event Processing (CEP) technologies is its flexible deployment model. In that sense, a StreamInsight solution can be hosted within an application or as a server component. This duality contrasts with most of the popular CEP frameworks in the current market which are almost exclusively server based. Whether it's undoubtedly that the ability of embedding a CEP engine in your applications opens new possibilities...(read more)

  Read the article

• AuthnRequest Settings in OIF / SP

  - by Damien Carru

  In this article, I will list the various OIF/SP settings that affect how an AuthnRequest message is created in OIF in a Federation SSO flow. The AuthnRequest message is used by an SP to start a Federation SSO operation and to indicate to the IdP how the operation should be executed: How the user should be challenged at the IdP Whether or not the user should be challenged at the IdP, even if a session already exists at the IdP for this user Which NameID format should be requested in the SAML Assertion Which binding (Artifact or HTTP-POST) should be requested from the IdP to send the Assertion Which profile should be used by OIF/SP to send the AuthnRequest message Enjoy the reading! Protocols The SAML 2.0, SAML 1.1 and OpenID 2.0 protocols define different message elements and rules that allow an administrator to influence the Federation SSO flows in different manners, when the SP triggers an SSO operation: SAML 2.0 allows extensive customization via the AuthnRequest message SAML 1.1 does not allow any customization, since the specifications do not define an authentication request message OpenID 2.0 allows for some customization, mainly via the OpenID 2.0 extensions such as PAPE or UI SAML 2.0 OIF/SP allows the customization of the SAML 2.0 AuthnRequest message for the following elements: ForceAuthn: Boolean indicating whether or not the IdP should force the user for re-authentication, even if the user has still a valid session By default set to false IsPassive Boolean indicating whether or not the IdP is allowed to interact with the user as part of the Federation SSO operation. If false, the Federation SSO operation might result in a failure with the NoPassive error code, because the IdP will not have been able to identify the user By default set to false RequestedAuthnContext Element indicating how the user should be challenged at the IdP If the SP requests a Federation Authentication Method unknown to the IdP or for which the IdP is not configured, then the Federation SSO flow will result in a failure with the NoAuthnContext error code By default missing NameIDPolicy Element indicating which NameID format the IdP should include in the SAML Assertion If the SP requests a NameID format unknown to the IdP or for which the IdP is not configured, then the Federation SSO flow will result in a failure with the InvalidNameIDPolicy error code If missing, the IdP will generally use the default NameID format configured for this SP partner at the IdP By default missing ProtocolBinding Element indicating which SAML binding should be used by the IdP to redirect the user to the SP with the SAML Assertion Set to Artifact or HTTP-POST By default set to HTTP-POST OIF/SP also allows the administrator to configure the server to: Set which binding should be used by OIF/SP to redirect the user to the IdP with the SAML 2.0 AuthnRequest message: Redirect or HTTP-POST By default set to Redirect Set which binding should be used by OIF/SP to redirect the user to the IdP during logout with SAML 2.0 Logout messages: Redirect or HTTP-POST By default set to Redirect SAML 1.1 The SAML 1.1 specifications do not define a message for the SP to send to the IdP when a Federation SSO operation is started. As such, there is no capability to configure OIF/SP on how to affect the start of the Federation SSO flow. OpenID 2.0 OpenID 2.0 defines several extensions that can be used by the SP/RP to affect how the Federation SSO operation will take place: OpenID request: mode: String indicating if the IdP/OP can visually interact with the user checkid_immediate does not allow the IdP/OP to interact with the user checkid_setup allows user interaction By default set to checkid_setup PAPE Extension: max_auth_age : Integer indicating in seconds the maximum amount of time since when the user authenticated at the IdP. If MaxAuthnAge is bigger that the time since when the user last authenticated at the IdP, then the user must be re-challenged. OIF/SP will set this attribute to 0 if the administrator configured ForceAuthn to true, otherwise this attribute won't be set Default missing preferred_auth_policies Contains a Federation Authentication Method Element indicating how the user should be challenged at the IdP By default missing Only specified in the OpenID request if the IdP/OP supports PAPE in XRDS, if OpenID discovery is used. UI Extension Popup mode Boolean indicating the popup mode is enabled for the Federation SSO By default missing Language Preference String containing the preferred language, set based on the browser's language preferences. By default missing Icon: Boolean indicating if the icon feature is enabled. In that case, the IdP/OP would look at the SP/RP XRDS to determine how to retrieve the icon By default missing Only specified in the OpenID request if the IdP/OP supports UI Extenstion in XRDS, if OpenID discovery is used. ForceAuthn and IsPassive WLST Command OIF/SP provides the WLST configureIdPAuthnRequest() command to set: ForceAuthn as a boolean: In a SAML 2.0 AuthnRequest, the ForceAuthn field will be set to true or false In an OpenID 2.0 request, if ForceAuthn in the configuration was set to true, then the max_auth_age field of the PAPE request will be set to 0, otherwise, max_auth_age won't be set IsPassive as a boolean: In a SAML 2.0 AuthnRequest, the IsPassive field will be set to true or false In an OpenID 2.0 request, if IsPassive in the configuration was set to true, then the mode field of the OpenID request will be set to checkid_immediate, otherwise set to checkid_setup Test In this test, OIF/SP is integrated with a remote SAML 2.0 IdP Partner, with the OOTB configuration. Based on this setup, when OIF/SP starts a Federation SSO flow, the following SAML 2.0 AuthnRequest would be generated: <samlp:AuthnRequest ProtocolBinding="urn:oasis:names:tc:SAML:2.0:bindings:HTTP-POST" ID="id-E4BOT7lwbYK56lO57dBaqGUFq01WJSjAHiSR60Q4" Version="2.0" IssueInstant="2014-04-01T21:39:14Z" Destination="https://acme.com/saml20/sso">   <saml:Issuer Format="urn:oasis:names:tc:SAML:2.0:nameid-format:entity">https://sp.com/oam/fed</saml:Issuer>   <samlp:NameIDPolicy AllowCreate="true"/></samlp:AuthnRequest> Let's configure OIF/SP for that IdP Partner, so that the SP will require the IdP to re-challenge the user, even if the user is already authenticated: Enter the WLST environment by executing:$IAM_ORACLE_HOME/common/bin/wlst.sh Connect to the WLS Admin server:connect() Navigate to the Domain Runtime branch:domainRuntime() Execute the configureIdPAuthnRequest() command:configureIdPAuthnRequest(partner="AcmeIdP", forceAuthn="true") Exit the WLST environment:exit() After the changes, the following SAML 2.0 AuthnRequest would be generated: <samlp:AuthnRequest ForceAuthn="true" ProtocolBinding="urn:oasis:names:tc:SAML:2.0:bindings:HTTP-POST" ID="id-E4BOT7lwbYK56lO57dBaqGUFq01WJSjAHiSR60Q4" Version="2.0" IssueInstant="2014-04-01T21:39:14Z" Destination="https://acme.com/saml20/sso">   <saml:Issuer Format="urn:oasis:names:tc:SAML:2.0:nameid-format:entity">https://sp.com/oam/fed</saml:Issuer>   <samlp:NameIDPolicy AllowCreate="true"/></samlp:AuthnRequest> To display or delete the ForceAuthn/IsPassive settings, perform the following operatons: Enter the WLST environment by executing:$IAM_ORACLE_HOME/common/bin/wlst.sh Connect to the WLS Admin server:connect() Navigate to the Domain Runtime branch:domainRuntime() Execute the configureIdPAuthnRequest() command: To display the ForceAuthn/IsPassive settings on the partnerconfigureIdPAuthnRequest(partner="AcmeIdP", displayOnly="true") To delete the ForceAuthn/IsPassive settings from the partnerconfigureIdPAuthnRequest(partner="AcmeIdP", delete="true") Exit the WLST environment:exit() Requested Fed Authn Method In my earlier "Fed Authentication Method Requests in OIF / SP" article, I discussed how OIF/SP could be configured to request a specific Federation Authentication Method from the IdP when starting a Federation SSO operation, by setting elements in the SSO request message. WLST Command The OIF WLST commands that can be used are: setIdPPartnerProfileRequestAuthnMethod() which will configure the requested Federation Authentication Method in a specific IdP Partner Profile, and accepts the following parameters: partnerProfile: name of the IdP Partner Profile authnMethod: the Federation Authentication Method to request displayOnly: an optional parameter indicating if the method should display the current requested Federation Authentication Method instead of setting it delete: an optional parameter indicating if the method should delete the current requested Federation Authentication Method instead of setting it setIdPPartnerRequestAuthnMethod() which will configure the specified IdP Partner entry with the requested Federation Authentication Method, and accepts the following parameters: partner: name of the IdP Partner authnMethod: the Federation Authentication Method to request displayOnly: an optional parameter indicating if the method should display the current requested Federation Authentication Method instead of setting it delete: an optional parameter indicating if the method should delete the current requested Federation Authentication Method instead of setting it This applies to SAML 2.0 and OpenID 2.0 protocols. See the "Fed Authentication Method Requests in OIF / SP" article for more information. Test In this test, OIF/SP is integrated with a remote SAML 2.0 IdP Partner, with the OOTB configuration. Based on this setup, when OIF/SP starts a Federation SSO flow, the following SAML 2.0 AuthnRequest would be generated: <samlp:AuthnRequest ProtocolBinding="urn:oasis:names:tc:SAML:2.0:bindings:HTTP-POST" ID="id-E4BOT7lwbYK56lO57dBaqGUFq01WJSjAHiSR60Q4" Version="2.0" IssueInstant="2014-04-01T21:39:14Z" Destination="https://acme.com/saml20/sso">   <saml:Issuer Format="urn:oasis:names:tc:SAML:2.0:nameid-format:entity">https://sp.com/oam/fed</saml:Issuer>   <samlp:NameIDPolicy AllowCreate="true"/></samlp:AuthnRequest> Let's configure OIF/SP for that IdP Partner, so that the SP will request the IdP to use a mechanism mapped to the urn:oasis:names:tc:SAML:2.0:ac:classes:X509 Federation Authentication Method to authenticate the user: Enter the WLST environment by executing:$IAM_ORACLE_HOME/common/bin/wlst.sh Connect to the WLS Admin server:connect() Navigate to the Domain Runtime branch:domainRuntime() Execute the setIdPPartnerRequestAuthnMethod() command:setIdPPartnerRequestAuthnMethod("AcmeIdP", "urn:oasis:names:tc:SAML:2.0:ac:classes:X509") Exit the WLST environment:exit() After the changes, the following SAML 2.0 AuthnRequest would be generated: <samlp:AuthnRequest ProtocolBinding="urn:oasis:names:tc:SAML:2.0:bindings:HTTP-POST" ID="id-E4BOT7lwbYK56lO57dBaqGUFq01WJSjAHiSR60Q4" Version="2.0" IssueInstant="2014-04-01T21:39:14Z" Destination="https://acme.com/saml20/sso">   <saml:Issuer Format="urn:oasis:names:tc:SAML:2.0:nameid-format:entity">https://sp.com/oam/fed</saml:Issuer>   <samlp:NameIDPolicy AllowCreate="true"/>   <samlp:RequestedAuthnContext Comparison="minimum">      <saml:AuthnContextClassRef xmlns:saml="urn:oasis:names:tc:SAML:2.0:assertion">         urn:oasis:names:tc:SAML:2.0:ac:classes:X509      </saml:AuthnContextClassRef>   </samlp:RequestedAuthnContext></samlp:AuthnRequest> NameID Format The SAML 2.0 protocol allows for the SP to request from the IdP a specific NameID format to be used when the Assertion is issued by the IdP. Note: SAML 1.1 and OpenID 2.0 do not provide such a mechanism Configuring OIF The administrator can configure OIF/SP to request a NameID format in the SAML 2.0 AuthnRequest via: The OAM Administration Console, in the IdP Partner entry The OIF WLST setIdPPartnerNameIDFormat() command that will modify the IdP Partner configuration OAM Administration Console To configure the requested NameID format via the OAM Administration Console, perform the following steps: Go to the OAM Administration Console: http(s)://oam-admin-host:oam-admin-port/oamconsole Navigate to Identity Federation -> Service Provider Administration Open the IdP Partner you wish to modify In the Authentication Request NameID Format dropdown box with one of the values None The NameID format will be set Default Email Address The NameID format will be set urn:oasis:names:tc:SAML:1.1:nameid-format:emailAddress X.509 Subject The NameID format will be set urn:oasis:names:tc:SAML:1.1:nameid-format:X509SubjectName Windows Name Qualifier The NameID format will be set urn:oasis:names:tc:SAML:1.1:nameid-format:WindowsDomainQualifiedName Kerberos The NameID format will be set urn:oasis:names:tc:SAML:2.0:nameid-format:kerberos Transient The NameID format will be set urn:oasis:names:tc:SAML:2.0:nameid-format:transient Unspecified The NameID format will be set urn:oasis:names:tc:SAML:1.1:nameid-format:unspecified Custom In this case, a field would appear allowing the administrator to indicate the custom NameID format to use The NameID format will be set to the specified format Persistent The NameID format will be set urn:oasis:names:tc:SAML:2.0:nameid-format:persistent I selected Email Address in this example Save WLST Command To configure the requested NameID format via the OIF WLST setIdPPartnerNameIDFormat() command, perform the following steps: Enter the WLST environment by executing:$IAM_ORACLE_HOME/common/bin/wlst.sh Connect to the WLS Admin server:connect() Navigate to the Domain Runtime branch:domainRuntime() Execute the setIdPPartnerNameIDFormat() command:setIdPPartnerNameIDFormat("PARTNER", "FORMAT", customFormat="CUSTOM") Replace PARTNER with the IdP Partner name Replace FORMAT with one of the following: orafed-none The NameID format will be set Default orafed-emailaddress The NameID format will be set urn:oasis:names:tc:SAML:1.1:nameid-format:emailAddress orafed-x509 The NameID format will be set urn:oasis:names:tc:SAML:1.1:nameid-format:X509SubjectName orafed-windowsnamequalifier The NameID format will be set urn:oasis:names:tc:SAML:1.1:nameid-format:WindowsDomainQualifiedName orafed-kerberos The NameID format will be set urn:oasis:names:tc:SAML:2.0:nameid-format:kerberos orafed-transient The NameID format will be set urn:oasis:names:tc:SAML:2.0:nameid-format:transient orafed-unspecified The NameID format will be set urn:oasis:names:tc:SAML:1.1:nameid-format:unspecified orafed-custom In this case, a field would appear allowing the administrator to indicate the custom NameID format to use The NameID format will be set to the specified format orafed-persistent The NameID format will be set urn:oasis:names:tc:SAML:2.0:nameid-format:persistent customFormat will need to be set if the FORMAT is set to orafed-custom An example would be:setIdPPartnerNameIDFormat("AcmeIdP", "orafed-emailaddress") Exit the WLST environment:exit() Test In this test, OIF/SP is integrated with a remote SAML 2.0 IdP Partner, with the OOTB configuration. Based on this setup, when OIF/SP starts a Federation SSO flow, the following SAML 2.0 AuthnRequest would be generated: <samlp:AuthnRequest ProtocolBinding="urn:oasis:names:tc:SAML:2.0:bindings:HTTP-POST" ID="id-E4BOT7lwbYK56lO57dBaqGUFq01WJSjAHiSR60Q4" Version="2.0" IssueInstant="2014-04-01T21:39:14Z" Destination="https://acme.com/saml20/sso">   <saml:Issuer Format="urn:oasis:names:tc:SAML:2.0:nameid-format:entity">https://sp.com/oam/fed</saml:Issuer> <samlp:NameIDPolicy AllowCreate="true"/></samlp:AuthnRequest> After the changes performed either via the OAM Administration Console or via the OIF WLST setIdPPartnerNameIDFormat() command where Email Address would be requested as the NameID Format, the following SAML 2.0 AuthnRequest would be generated: <samlp:AuthnRequest ForceAuthn="false" IsPassive="false" ProtocolBinding="urn:oasis:names:tc:SAML:2.0:bindings:HTTP-POST" ID="id-E4BOT7lwbYK56lO57dBaqGUFq01WJSjAHiSR60Q4" Version="2.0" IssueInstant="2014-04-01T21:39:14Z" Destination="https://acme.com/saml20/sso">   <saml:Issuer Format="urn:oasis:names:tc:SAML:2.0:nameid-format:entity">https://sp.com/oam/fed</saml:Issuer> <samlp:NameIDPolicy Format="urn:oasis:names:tc:SAML:1.1:nameid-format:emailAddress" AllowCreate="true"/></samlp:AuthnRequest> Protocol Binding The SAML 2.0 specifications define a way for the SP to request which binding should be used by the IdP to redirect the user to the SP with the SAML 2.0 Assertion: the ProtocolBinding attribute indicates the binding the IdP should use. It is set to: Either urn:oasis:names:tc:SAML:2.0:bindings:HTTP-POST for HTTP-POST Or urn:oasis:names:tc:SAML:2.0:bindings:Artifact for Artifact The SAML 2.0 specifications also define different ways to redirect the user from the SP to the IdP with the SAML 2.0 AuthnRequest message, as the SP can send the message: Either via HTTP Redirect Or HTTP POST (Other bindings can theoretically be used such as Artifact, but these are not used in practice) Configuring OIF OIF can be configured: Via the OAM Administration Console or the OIF WLST configureSAMLBinding() command to set the Assertion Response binding to be used Via the OIF WLST configureSAMLBinding() command to indicate how the SAML AuthnRequest message should be sent Note: the binding for sending the SAML 2.0 AuthnRequest message will also be used to send the SAML 2.0 LogoutRequest and LogoutResponse messages. OAM Administration Console To configure the SSO Response/Assertion Binding via the OAM Administration Console, perform the following steps: Go to the OAM Administration Console: http(s)://oam-admin-host:oam-admin-port/oamconsole Navigate to Identity Federation -> Service Provider Administration Open the IdP Partner you wish to modify Check the "HTTP POST SSO Response Binding" box to request the IdP to return the SSO Response via HTTP POST, otherwise uncheck it to request artifact Save WLST Command To configure the SSO Response/Assertion Binding as well as the AuthnRequest Binding via the OIF WLST configureSAMLBinding() command, perform the following steps: Enter the WLST environment by executing:$IAM_ORACLE_HOME/common/bin/wlst.sh Connect to the WLS Admin server:connect() Navigate to the Domain Runtime branch:domainRuntime() Execute the configureSAMLBinding() command:configureSAMLBinding("PARTNER", "PARTNER_TYPE", binding, ssoResponseBinding="httppost") Replace PARTNER with the Partner name Replace PARTNER_TYPE with the Partner type (idp or sp) Replace binding with the binding to be used to send the AuthnRequest and LogoutRequest/LogoutResponse messages (should be httpredirect in most case; default) httppost for HTTP-POST binding httpredirect for HTTP-Redirect binding Specify optionally ssoResponseBinding to indicate how the SSO Assertion should be sent back httppost for HTTP-POST binding artifactfor for Artifact binding An example would be:configureSAMLBinding("AcmeIdP", "idp", "httpredirect", ssoResponseBinding="httppost") Exit the WLST environment:exit() Test In this test, OIF/SP is integrated with a remote SAML 2.0 IdP Partner, with the OOTB configuration which requests HTTP-POST from the IdP to send the SSO Assertion. Based on this setup, when OIF/SP starts a Federation SSO flow, the following SAML 2.0 AuthnRequest would be generated: <samlp:AuthnRequest ProtocolBinding="urn:oasis:names:tc:SAML:2.0:bindings:HTTP-POST" ID="id-E4BOT7lwbYK56lO57dBaqGUFq01WJSjAHiSR60Q4" Version="2.0" IssueInstant="2014-04-01T21:39:14Z" Destination="https://acme.com/saml20/sso">   <saml:Issuer Format="urn:oasis:names:tc:SAML:2.0:nameid-format:entity">https://sp.com/oam/fed</saml:Issuer>   <samlp:NameIDPolicy AllowCreate="true"/></samlp:AuthnRequest> In the next article, I will cover the various crypto configuration properties in OIF that are used to affect the Federation SSO exchanges.Cheers,Damien Carru

  Read the article

< Previous Page | 209 210 211 212 213 214 215 216 217 218 219 220  | Next Page >