Search Results

Search found 5685 results on 228 pages for 'encrypted partition'.

Page 213/228 | < Previous Page | 209 210 211 212 213 214 215 216 217 218 219 220  | Next Page >

  • Is it a good Idea to switch to a SSD to use less battery?

    - by Walter Maier-Murdnelch
    I am thinking of buying a SSD for my laptop, mainly for the purpose of extended operating time when running on battery. At the moment I use a Hitachi HTS545032B9A300 (320GB) (Datasheet) as main drive and a Seagate Momentus 5400.3 120GB as secondary drive. I dualboot Windows and Linux but I don't need the windows partition any longer, a 120GB SDD would be more than sufficient space-wise. Speed is not an issue for me, I make heavy use of tmpfs (ramdrive) within Linux and transfers of bigger files are mainly through some network filesystem anyways, thus a cheaper SSD should do. For the purpose of comparison I chose the OCZ Vertex Plus 120GB. Power consumption always is a big promotional thing the industry uses to make me want to buy their SSDs, some sheet on the OCZ page provides an astonishing comparison of desktop HDDS and SSDs. The numbers I got comparing my laptop HDD and their SSD were not really astonishing any longer. Hitachi 320GB HDD: Startup (W, peak, max.) 4.5 Seek (W, avg.) 1.7 Read / Write (W, avg.) 1.4 Performance idle (W, avg.) 1.3 Active idle (W, avg.) 0.8 Low power idle (W, avg.) 0.5 Standby (W, avg.) 0.2 Sleep 0.1 OCZ 120GB SSD: 1.5W active 0.3W standby I see that there are differences, but actually they don't seem that high as I though they were. And compared to the power consuption of the rest of my system I wonder if it makes a difference at all. Have I just taken the wrong look at the whole thing or may I be better off to buy another battery for my laptop?

    Read the article

  • How to fix Truecrypt MBR using Command Prompt or Linux live USB?

    - by Michal Stefanow
    I was playing with TrueCrypt and decided to make a fresh installation of Windows 7 from USB stick. Unfortunately Windows 7 installer: "setup was unable to create a new system partition" My entire HDD has been formatted and is visible as 320GB unallocated space, but no fdisk nor Windows 7 installer nor Windows XP installer could help. (Windows XP doesn't even see the HDD, it sees only USB stick and says "not enough space to install") It may be related to Truecrypt and pre-boot authentification, boot loader and/or MBR. As I don't have optical device I could not have created rescue disk. Right now I need a rescue of some kind, supposingly by erasing/fixing MBR using Linux live USB or using Command Promt. Another approach is to click "repair your comuter" menu from Windows 7 installer then click "restore your computer", then click OK upon error and get access to Command Prompt. Yet another another approach is to start computer without Linux USB I receive this: error:unknown filesystem. grub rescue> Any help would be greatly appreciated as my laptop is kind of not fully operational now. UPDATE: This was asked long time ago, ended up formatting everything (eventually it worked using different bootable USB)...

    Read the article

  • Resize a RAID 1 volume on OSX Snow Leopard - how? (Note: software raid)

    - by Emmel
    I've scoured the Internet in search of an answer to this question, and as usual with OSX-related topics, I often don't find any deep-dive technical explanations sufficient enough to feel confident doing dangerous things. Here is my question: I have a Mac Pro, running OSX 10.6.2. I have, as my main root/boot disk, a RAID 1 volume called "Mirror1". Mirror1 is comprised of two 1 TB disks. Mirror1, however, is fixed at 640 GB. That's because, I originally took a 640GB disk, bought a terabyte disk, mirrored it (using diskutil appleraid enable...), when it synced I removed the 640GB and replaced it with a second 1 TB disk, and synced again. Voila! A single 640 GB replaced by two 1 TB disks in a mirror.. Actually, no. There's still something missing from the equation: Mirror1 needs to be expanded from 640GB to 1 TB to match the partition sizes on each of those disks. How do I do this? Perhaps the diskutil output will help: -> diskutil list /dev/disk0 #: TYPE NAME SIZE IDENTIFIER 0: GUID_partition_scheme *1.0 TB disk0 1: EFI 209.7 MB disk0s1 2: Apple_RAID 999.9 GB disk0s2 3: Apple_Boot Boot OSX 134.2 MB disk0s3 /dev/disk1 #: TYPE NAME SIZE IDENTIFIER 0: GUID_partition_scheme *1.0 TB disk1 1: EFI 209.7 MB disk1s1 2: Apple_RAID 999.9 GB disk1s2 3: Apple_Boot Boot OSX 134.2 MB disk1s3 /dev/disk2 #: TYPE NAME SIZE IDENTIFIER 0: GUID_partition_scheme *640.1 GB disk2 1: EFI 209.7 MB disk2s1 2: Apple_HFS Mac Disk 2 536.7 GB disk2s2 3: Microsoft Basic Data BOOTCAMP 103.1 GB disk2s3 /dev/disk3 #: TYPE NAME SIZE IDENTIFIER 0: Apple_HFS Mirror1 *639.8 GB disk3 -> diskutil appleraid list AppleRAID sets (1 found) =============================================================================== Name: Macintosh HD Unique ID: 1953F864-B474-4EB6-8E69-41834EBD0247 Type: Mirror Status: Online Size: 639.8 GB (639791038464 Bytes) Rebuild: manual Device Node: disk3 ------------------------------------------------------------------------------- # Device Node UUID Status ------------------------------------------------------------------------------- 0 disk1s2 25109BAE-5697-40EA-B612-0217851444F7 Online 1 disk0s2 11B83AB0-8148-4DB6-8761-DEF08C855F8D Online =============================================================================== Thanks in advance.

    Read the article

  • Compatibility of Fedora install on a Hybrid drive

    - by kjh
    I recently bought un ultrabook with a 500gb/32gb sdd hdd hybrid drive, and I'm having trouble replacing windows on it with fedora seventeen. it errors out saying there was an unhandled exception. Is linux compatible with hybrid drives? or can the operating system on a hybrid drive not be replaced? Edit: here are the steps I select special storage devices because it ignores my hard drives otherwise at this point i get the message: "Disk contains bios raid meta data, disk sda will be ignored" I can pick a hostname, select my timezone and set a password at the install type screen, no matter what I select (use all free space, replace linux systems, create custom partition etc..) once I click next, it says "an unhandled exception" has occured. and I can no longer proceed with installation. Here is the error message: anaconda 17.29 exception report Traceback (most recent call first); File "/usr/lib64/python2.7/size-packages/pyanaconda/bootloader.py"; line 183 self.stage1_drive=self_drives[0] File "/usr/lib64/python2.7/site-packages/pyanaconda/rw/cleardisks_gui.ph"; line... and tons of more lines like that

    Read the article

  • Server 2008 RAID 5 Write Speeds

    - by Solipsism
    I recently configured a RAID 5 partition in Server 2008 with 4 RAID 5 disks. These disks are connected through a SATA expansion card that uses PCIe. This morning, I checked and they had finally finished synchronizing, and so I tried to do some speed tests. Copying off the disks started pretty much fine - speeds began at 125MB/s, then trailed down to about 70MB/s, which I found odd but not worrying. Writing TO the disks however is a completely different story. I attempted to copy some of my VM host ISOs onto the disks (~2-4 GB apiece) and this resulted in speeds of approximately 10MB/s. I tried copying both from a local disk (connected directly to the motherboard) and from another server ththe gigabit network and results were the same. I checked the performance monitor while transferring the files and the only thing that stuck out was that my memory hard faults shot up to 6,000 per minute (spiking around 200/s) by explorer.exe. The system is running 2GB of DDR667 ECC RAM and a quad-core 2.3GHz opteron. Is there anything I can do to fix this performance issue (buy more RAM? move the drives to a faster box?, etc) or am I just screwed so long as I stick to windows.

    Read the article

  • De-duplicating backup tool on a block basis? [closed]

    - by SST
    I am looking for an (ideally free as in speech or beer) backup tool for Unix-like OS which can store deduplicated backups, i.e. only nonredundant content takes up additional space. I already looked at dirvish (my first candidate) and rsnapshot which use hardlinks to achieve deduplication on a per-file level. However, as I want to back up large files (Thunderbird mailboxes 3GB, VMware images 10GB), such file are stored again entirely even if just a few bytes change. Then there are rsync-based tools like rdiff-backup which only store deltas and a current mirror. However, as the deltas are generated against each previous mirror, it is difficult to fine-tune the retention granularity (only keep one backup after a week, etc.) because the deltas would have to be re-evaluated. Another approach is to partition content into blocks and store each block only if it is not stored yet, otherwise just linking it to the first occurrence. The only tool I know of that does this by now is obnam (http://liw.fi/obnam), and it even supports zlib-compression and gpg-encryption -- nice! But it is very slow, AFAICT. Does any one know any other, solid backup software which supports deduplication on a sub-file level, ideally with at least some management options (show/select/delete generations...)?

    Read the article

  • Debian Wheezy (testing) df reported volume size

    - by TheRoadrunner
    I am a bit confused about the /dev/sda* references since I installed Wheezy instead of Squeeze on a testing box. fdisk -l returns: Disk /dev/sda: 250.1 GB, 250059350016 bytes 255 heads, 63 sectors/track, 30401 cylinders, total 488397168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x000e9623 Device Boot Start End Blocks Id System /dev/sda1 * 2048 480278527 240138240 83 Linux /dev/sda2 480280574 488396799 4058113 5 Extended /dev/sda5 480280576 488396799 4058112 82 Linux swap / Solaris This seems correct. But df -h /dev/sda (and /dev/sda1 and /dev/sda2 and /dev/sda5) returns: Filesystem Size Used Avail Use% Mounted on udev 10M 0 10M 0% /dev The same happens with every entry under /dev/disk/by-id and /dev/disk/by-path. Only one of two entries under /dev/disk/by-uuid returns the correct volume size: df -h /dev/disk/by-uuid/cacdbad6-7e6b-4e80-84ba-e3c77ef48796 Filesystem Size Used Avail Use% Mounted on /dev/disk/by-uuid/cacdbad6-7e6b-4e80-84ba-e3c77ef48796 229G 22G 196G 11% / Contents of /etc/fstab: # /etc/fstab: static file system information. # # Use 'blkid' to print the universally unique identifier for a # device; this may be used with UUID= as a more robust way to name devices # that works even if disks are added and removed. See fstab(5). # # <file system> <mount point> <type> <options> <dump> <pass> # / was on /dev/sda1 during installation UUID=cacdbad6-7e6b-4e80-84ba-e3c77ef48796 / ext4 errors=remount-ro 0 1 # swap was on /dev/sda5 during installation UUID=45840d13-ee36-4e77-8e73-16cbdff25eb1 none swap sw 0 0 /dev/sr0 /media/cdrom0 udf,iso9660 user,noauto 0 0 /dev/fd0 /media/floppy0 auto rw,user,noauto 0 0 It seems all other references than the uuid points to the swap partition. Is this because Wheezy is in testing, and should it be reported as an error?

    Read the article

  • How to tell Linux to explicitly swap out main memory of a suspended process?

    - by Vi
    I run a memory-hungry process (mkcromfs) which consumes more memory than I have physical memory on my latop, so it is paging and swappin and thrashing all the time and loadavg is about 2 (compcache is already in use with usual swap partition as well), but slowly moving forward (Although I afraid it will finally try to allocate 2GB and crash draining 2 days of thrashing). When I want to use the laptop for something else, I stop the process, start X server, firefox and other programs. The problem is that when I start Firefox the loadavg jumps to 10 and the system becomes almost unresponsive at all (long time to turn on/off caps lock, slow mouse cursor position updates, slow switching from X server to Linux console, slow login). The stopped mkcromfs still holds a lot of memory (464.8 MiB and slowly falling) and moves it to swap only when more memory is needed for some other program, which results in a great slowdown. How to tell the Linux to swap out this process entirely (e.g. I'm not intending to resume it in short term), possibly waking from swap other data? Also it will be useful to be able to specify the exact swap device to swap the given process out.

    Read the article

  • GRUB having problems with my sda1 UUID

    - by Igoru
    I was having trouble trying to setup triple boot on my computer... (Take a look at this thread if you think it would help). I ended up by having a GRUB menu that has Ubuntu entries and "Windows" entry, that calls an EasyBCD menu to choose between Windows 7 and XP. Everything would be fine if, only if, GRUB was set up correctly. I can't find why, but it throws me this when I try to open Ubuntu: I've already tried to remove the menu.lst and do a grub-update, and a grub-install too. I tried to create a symlink to /dev/sda1 at /dev/disk/by-uuid/<<uuid that is there>>, just like the other UUIDs that were there... But I couldn't find that symlink at that busybox that opened when it thrown me the error. Any ideas? [UPDATE] This is the GRUB entry with problems: title Ubuntu 9.04, kernel 2.6.28-15-generic uuid b1ed36e5-4d84-4eb8-86ef-6f1135ffc238 kernel /boot/vmlinuz-2.6.28-15-generic root=UUID=b1ed36e5-4d84-4eb8-86ef-6f1135ffc238 ro quiet splash initrd /boot/initrd.img-2.6.28-15-generic quiet And this my /dev/disk/by-uuid folder: 04DCBCFBDCBCE856 - ../../sdb1 (NTFS backup disk) 4434E77734E769FE - ../../sda4 (NTFS WinXP) ACB09F0DB09EDCE0 - ../../sda2 (NTFS Win7) b5311be8-a853-4fdd-aed5-d65974b3c0c4 - ../../sda5 (EXT4 home) C04B-4D97 - ../../sdc (FAT32 live-pendrive from which i'm running) D28447F68447DB9B - ../../sda6 (NTFS files partition) e0e88f38-d815-423a-9d5e-64b9c74a8b92 - ../../sda7 (swap)

    Read the article

  • Reusing Raid 5 Drive?

    - by User125
    We have two servers (ML530 G2 and DL380G2) w/ identical HP 10K RPM SCSI drives w/ a raid 5. One is decommissioned and the other will be decommissioned shortly. However, one of the drives on the production server had a drive failure. My hope was to take one of the drives from the decommissioned server and pop it into the production server. Both are running RAID 5. I broke the array on the decomm. server. To my knowledge, that should have wiped out all the volume and partition information. However, I do not know if it is safe to then take a drive from the decomm'ed server and replace the failed drive. Will the existing array see it as a replacement drive, wipe it and rebuild? Or will it fail because it was used in an array before. Are there any remnant data that resides on the drives after deleting a raid 5 array? These servers are 10-15 years old, so we're just trying to keep them alive until we decommission it. I'm not looking to pay a premium to find a vendor that still sells replacement drives for this system.

    Read the article

  • How to Dual-Boot Kali-Linux and Windows 8.1?

    - by Ceyhun
    I have Acer V3-772G 1 TB Harddisk. I shrinked my biggest partition in order to install Kali Linux. When installing Kali, GRUB couldn't detect windows 8 so I kept going on(I installed grub as my masterboot). After installed Kali there was no way to boot Windows 8.1, but booting Kali was OK with GRUB in legacy-BIOS. When I tried to change bios to UEFI it couldn't find any OS (took too much time, nearly 1 hour). So I tried to update GRUB with boot-repair within a Ubuntu Live USB. But after updating GRUB I terrified, in UEFI and Legacy mode grub couldn't find ANY OS (Both Kali and Windows) so I have no option other than using Ubuntu Live. I tried every possible options but nothing has worked for me. I tried rEFInd in UEFI mode it worked only for Kali. I still cannot boot my windows 8.1 . I considered to restore to factory setting with a Windows Rescue USB but kept telling me "No driver found". Please help me to dual boot or remove Kali and restore my Windows 8.1

    Read the article

  • What games work well on MacBook Pro (i7/GeForce GT 330M) within VMWare Fusion?

    - by webworm
    I have a 15" MacBook Pro (2.66 i7 with 8 GB RAM) with the GeForce GT 330M 512 MB graphics card. I use it primarily for development (Mac/Web/Windows) though I would like to play the occasional game with my son who uses a desktop PC system at home. I prefer to use VMWare Fusion for virtualization rather than BootCamp for a number of reasons. Heat/Fan issues with i7 under BootCamp Prefer to retain virtual machine as single file rather than dedicated partition (easier to move a nd backup) I have heard that Windows support of the GeForce GT 330 in BootCamp is not all that good. So that being said I was wondering what sort of games I would be able to play within the Fusion environment running Windows 7. I have 8 GB RAM and usually dedicate 4 GB to the virtual machine. I don't expect to be able to play the latest FPS games such as BattleField: Bad Company 2 or Call of Duty, rather I am looking at games such a Total War II, Civilizations IV, Supreme Commander, and other RTS type games. I should mention the native screen resolution of my MacBook Pro is 1680x1050, which is what I would be most likely running the VM at (fullscreen). Thank you for any advice.

    Read the article

  • What diagnostics are safe to run on an SSD drive?

    - by Peter Mounce
    I have a MacBook Pro (late 2010) with a Crucial RealSSD 256Gb in it; 60Gb is given to the Windows 7 x64 BootCamp partition. I have a USB-attached 500Gb drive for (most) data. In the last day or so, I've had a BSOD and several OS freezes (both Mac OSX 10.6.6 and Win7). The system in both cases will boot fine (at the moment!) and then run things fine, then some time later a program will stop responding, followed shortly thereafter by the system as a whole, forcing a reboot. This smacks to me of a storage problem. Given that I have an SSD and not a regular magnetic HDD, what are my next steps, in both OS'? I haven't seen anything pertinent in Windows' event-log. I'm not sure of the equivalent place to look in OSX; it's never given me issue to find out. What are my options for attempting to save my data from the SSD to another drive, given that after some small amount of time (eg half an hour), the OS stops responding? What are the recommended next steps?

    Read the article

  • problem transferring Win 7 operating system hard drive to be used as external hard drive

    - by itserich
    Win 7 Asus MA479 8GB Ram hard drives are 500GB The operating system was a Caviar Green, and I tried to exchange it for a Caviar Blue. The Caviar Blue took the install correctly, but the Green, the prior operating system hard drive, will not allow itself to be used as an external hard drive. I use TrueCrypt and tried to format the Green and it freezes each time at the very end of the encyrption of the partition. I took the Blue out of the system and tried to encrypt it, and same problem. I think there must be something on the hard drive that shows it was a system drive and it causes a conflict. I have tried writing over the system hard drive to fully erase everything but that does not work, it still freezes. The drives will work in a different pc, i.e. other pc where it never was the system drive. The external hard drive is connected esata through Thermaltake. I have used TrueCrypt on various pc's for years including this Win7 with no problem. Thank you.

    Read the article

  • Why does my simple Raid 1 backup storage perform really slow sometimes?

    - by randomguy
    I bought 2x Samsung F3 EcoGreen 2TB hard disks to make a backup storage. I put them in Raid 1 (mirror) mode. Made a single partition and formatted it to NTFS, running Windows 7. For some reason, accessing the drive's contents (simply by navigating folders) is sometimes really slow. Like opening D:/photos/ can sometimes take several seconds before it starts showing any of the folder's contents. Same applies for other folders. What could be causing this and what could I do to improve the performance? I remember that there was an option somewhere inside Windows to choose fast access but less reliable persistence operations (read/write). It was a tick inside some dialog. At the time, it felt like a good idea to take the tick away from the option and get more reliable persistence but slower access, but now I'm regretting. I'm unable to find this dialog.. I've looked hard. I don't know, if it would make any difference. Oh, and I've ran scan disk and defrag on the drive. No errors and speed isn't improved.

    Read the article

  • Boot stuck at blinking cursor before GRUB - only works via BIOS boot menu

    - by delta1
    I have a new box running Debian Squeeze. Grub is installed on /dev/sda, but when booting up I just get a blinking cursor, before the Grub menu. I can only boot to grub successfully when I choose boot options (during post) and select that specific drive! I have made sure the correct drive is set to boot first in the BIOS. So Grub works, but the system won't boot to that drive automatically? Any ideas on what could cause this? Drives sda/b/c are all 2TB (sda runs the system with b/c as raid device md0) with the following partitions: $ cat /proc/partitions major minor #blocks name 8 0 1953514584 sda 8 1 977 sda1 8 2 9765625 sda2 8 3 6445313 sda3 8 4 1937302627 sda4 8 32 1953514584 sdc 8 16 1953514584 sdb 9 0 1953513424 md0 but # fdisk -l /dev/sda gives WARNING: GPT (GUID Partition Table) detected on '/dev/sda'! The util fdisk doesn't support GPT. Use GNU Parted. Disk /dev/sda: 2000.4 GB, 2000398934016 bytes 255 heads, 63 sectors/track, 243201 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Device Boot Start End Blocks Id System /dev/sda1 1 243202 1953514583+ ee GPT Any insight into this strange behaviour would be greatly appreciated.

    Read the article

  • lamp -- edit PHP file but doesn't change web output -- including die()

    - by Reid W
    Server is standard Linux server on Amazon Web Services. Cent OS 5/Apache/PHP 5.3. No APC. It's worked fine for over a year, but now when I edit some but not all PHP files on the server using vi, the changes don't affect the web output. For example, I edit myfile.php and put a die() at the top, but when I load the page in my web browser, instead of the die() I see the content that would show up if the die() weren't there. svn updating the file in question doesn't help either. Files are on an Amazon EBS partition symlinked to /var/www/html. Just to reiterate -- this has worked fine for a long time. Restarting apache didn't help, nor did rebooting the server. What's weird is that it's just some of the files but not all. File ownership/permissions are the same for the "good" and "problem" files. I'm not a Linux newbie but am at a complete loss with this, and couldn't find anything on Google either. Any hints would be much appreciated!

    Read the article

  • Kickstarting an Ubuntu Server 10.04 installation (DHCP fails)

    - by William
    I'm trying to automate the network installation of Ubuntu 10.04 LTS with an anaconda kickstart and everything seems to running except for the initial DHCP autoconfiguration. The installer attempts to configure the install via DHCP but fails on its first attempt. This brings me to a prompt where I can retry DHCP and it seems to always work on the second attempt. My issue is that this is not really automated if I have to hit retry for DHCP. Is there something I can add to the kickstart file so that it will automatically retry or better yet not fail the first time? Thanks. Kickstart: # System language lang en_US # Language modules to install langsupport en_US # System keyboard keyboard us # System mouse mouse # System timezone timezone America/New_York # Root password rootpw --iscrypted $1$unrsWyF2$B0W.k2h1roBSSFmUDsW0r/ # Initial user user --disabled # Reboot after installation reboot # Use text mode install text # Install OS instead of upgrade install # Use Web installation url --url=http://10.16.0.1/cobbler/ks_mirror/ubuntu-10.04-x86_64/ # System bootloader configuration bootloader --location=mbr # Clear the Master Boot Record zerombr yes # Partition clearing information clearpart --all --initlabel # Disk partitioning information part swap --size 512 part / --fstype ext3 --size 1 --grow # System authorization infomation auth --useshadow --enablemd5 %include /tmp/pre_install_ubuntu_network_config # Always install the server kernel. preseed --owner d-i base-installer/kernel/override-image string linux-server # Install the Ubuntu Server seed. preseed --owner tasksel tasksel/force-tasks string server # Firewall configuration firewall --disabled # Do not configure the X Window System skipx %pre wget "http://10.16.0.1/cblr/svc/op/trig/mode/pre/system/Test-D" -O /dev/null # Network information # Start pre_install_network_config generated code # Start of code to match cobbler system interfaces to physical interfaces by their mac addresses # Start eth0 # Configuring eth0 (00:1A:64:36:B1:C8) if ip -o link show | grep -i 00:1A:64:36:B1:C8 then IFNAME=$(ip -o link show | grep -i 00:1A:64:36:B1:C8 | cut -d" " -f2 | tr -d :) echo "network --device=$IFNAME --bootproto=dhcp" >> /tmp/pre_install_ubuntu_network_config fi # End pre_install_network_config generated code %packages openssh-server

    Read the article

  • How to tell Linux to explicitly swap out main memory of suspended process?

    - by Vi
    I run a memory-hungry process (mkcromfs) which consumes more memory than I have physical memory on my latop, so it is paging and swappin and thrashing all the time and loadavg is about 2 (compcache is already in use with usual swap partition as well), but slowly moving forward (Although I afraid it will finally try to allocate 2GB and crash draining 2 days of thrashing). When I want to use the laptop for something else, I stop the process, start X server, firefox and other programs. The problem is that when I start Firefox the loadavg jumps to 10 and the system becomes almost unresponsive at all (long time to turn on/off caps lock, slow mouse cursor position updates, slow switching from X server to Linux console, slow login). The stopped mkcromfs still holds a lot of memory (464.8 MiB and slowly falling) and moves it to swap only when more memory is needed for some other program, which results in a great slowdown. How to tell the Linux to swap out this process entirely (e.g. I'm not intending to resume it in short term), possibly waking from swap other data? Also it will be useful to be able to specify the exact swap device to swap the given process out.

    Read the article

  • How do I set up Grub properly to quad-boot Windows, Mac OS X, Linux, and FreeBSD?

    - by Joe
    Grub has gone completely insane on me. My quad-boot system was working great up until I upgraded Ubuntu to 12.04. Since Ubuntu overwrote the Grub stuff I had to repair it with my Mac OS X and FreeBSD entries. After this, trying to boot Mac OS X gave me the error "couldn't open file" and FreeBSD gave the error "no such partition". Windows and Ubuntu worked fine. So I tried repairing again because I figured something must've gone wrong in the install process. Then only Ubuntu would boot. Trying to boot Windows would give me the error "no argument specified". I tried repairing Grub once again, since I seemed to be getting different results each time. This time, Ubuntu no longer appeared in the Grub menu, and the errors for the other OSes were the same. So I booted into the Ubuntu 12.04 live CD and ran Boot-Repair with recommended settings. Now Grub is completely skipped and Windows boots up. I have absolutely no idea what is going on or why I get different results every time I reinstall Grub. Here is how my partitions are set up: sda1 - Storage drive, sdb1 - Windows, sdb2 - Mac OS X, sdb3 - FreeBSD, sdb4 - Extended, sdb5 - Ubuntu, sdb6 - Shared storage, sdb7 - Shared Storage, Here's my grub.cfg file: grub.cfg

    Read the article

  • Cannot install windows. Compaq Presario CQ62

    - by Matthew
    I bought a used Compaq Presario CQ62 for cheap, and went to install windows on it. I formatted the partition and went to install when I got this error.... Windows cannot install required files. The file may be corrupt or missing. Make sure all files required for installation are available and restart the installation. Error code: 0x80070017 I have used this disk before with no problems, but internet searching suggested I burn one at 2x speed because that helps for some reason... I'm burning one now, but my question is, why would I get this error, OTHER than the disc being bad? I'm pretty certain this one isn't as I have used it before... (ok so the slowly burned cd (using imgburn) didn't work either so it's DEFINITELY not the disc) Thanks in advanced for any answers Also I took one stick of ram out because internet searching also suggested that, but it didn't make a difference. Also I ran memory and hard drive checks and they passed fine. Also I reset the motherboard options to default What could it be!? Help I'm completely stumped...

    Read the article

  • A very peculiar problem with an old pc and a newer laptop...

    - by user553492
    I got my old pc ( 248mb ram , 80 GB ) repaired and the tech people put XP in it .My newer laptop has UBUNTU 10.04 .now I only have one cable and one usb cord .So I connected my modem (with only one CAT5 port and 4 usb ports ) to laptop with CAT5 cable .Th internet is working fine . I also wanted to use net on older pc so I installed the usb drivers for win and it worked. But I got fed up of win xp and made a separate partition for FreeBSD which I planned to install .During the install I screwd up sumthing and now freebsd starts with a boot option with a ? mark in place of win xp .If I click on that it gives me a "NTLDR missing " msg. I tried connecting CAT5 cable between old and new pc and tried connecting my laptop with USB cable but nothing happend and then I realozed the modem doesnt have a WORKING usb driver for LINUX :( .FCUK ! .Freebsd doesnt` even detect the LAN cable if I use it for old pc . So basically I have a old pc that has FREEBSD which I can olny start and stare at the blank terminal console but works perfectly otherwise .FREEBSD was supposed to detect the LAN cable ??.And I have a laptop that has LINUX which only works if I connect it with a CAT5 cable .wtf . So what can I do with my old pc ??? any local server (if possible :( ) or some such thing ? or can u suggest any use .Im 18 and im into learning programming , coding .So I can practice it .Thankx !

    Read the article

  • Can I install windows on an SSD and access data from my old windows HDD?

    - by nzifnab
    I purchased new computer components, switching my hardware from AMD and Radeon to Intel and Nvidia. I kept components from my old computer like the powersupply and two HDDs. Everything appeared to install correctly and the system booted into the BIOS just fine (after a brief snafu with the CPU fan). My goal was to use the two harddrives and just be able to turn on the computer and load up my old windows install with all the files, programs, and documents. I expected to have to call Microsoft to re-register the windows install for the new hardware (since I had to do that last time I upgraded w/ the same windows version). When the computer attempts to boot into windows it briefly flashes a bluescreen and then restarts. System recovery gives a message something like "BadDriver Failover" something something. I assume this is because it's trying to use amd drivers for an intel chipset (or something...?) and I've been as-yet unsuccessful in getting it to boot into my old windows partition. SO! I decided eff it, maybe I'll go visit my nearest Micro Center and buy a 200 GB SSD, install windows onto that, and then... be able to access just the contents of both of my other harddrives? I don't intend on running any of the programs but there were some saved files I would like to salvage from the 500 GB harddrive, The 1.5 TB harddrive only had files on it, no OS or applications so I'd also expect to still be able to access it. Is this possible? Can I install the SSD and only format/install windows onto it and still access the contents from my two transferred-over drives?

    Read the article

  • How to fix Windows 7 when System Recovery Options hangs?

    - by seansand
    The battery power ran out on my HP G60 laptop and it shut down. Even after recharging, Windows 7 will now not start up. After any attempted startup, it bluescreens and takes me to the "Startup Repair (recommended)" / "Start Windows Normally" console screen. "Startup Repair (recommended)" appears to be the right choice, but when I choose it, I get taken to a screen which appears to be System Recovery Options (it's the same wallpaper as the screenshots here: http://www.sevenforums.com/tutorials/668-system-recovery-options.html). However, I just get a cursor with nothing else; no "System Recovery Options" window ever pops up. (A black console screen does pop up for a split-second but too fast to be able to read the text.) The empty screen with cursor hangs indefinitely. System Recovery Options normally runs off of a partition on the laptop hard drive. When I got the laptop, I also created a System Repair Disc (in fact I have more than one) and when I try use any of them; they all result in the same wallpaper and empty screen with lone cursor. Ctrl-Alt-Del does nothing. The computer did not come with a Windows 7 installation disc, so there's no obvious way to reinstall Windows 7. Safe mode does not work; startup fails and I just get sent back to the "Startup Repair (recommended)"/"Start Windows Normally" console screen. "Start in last good state" does not work either, same result as above. Running a memory & hard disk check found no errors. Do I have any options at all? "System Recovery Options" seems to be what I want, but the screen that is supposed to take me to them just hangs.

    Read the article

  • Almost All Logical Volumes Disappeared - Recovery?

    - by Alex
    We had a hard disc crash of one of two hard discs in a software raid with a LVM on top. The server is running Citrix xenserver. On the hard disk which is still intact, the volume group gets detected well, but only one LV is left. (some hashes replaced by "x") # lvdisplay --- Logical volume --- LV Name /dev/VG_XenStorage-x-x-x-x-408b91acdcae/MGT VG Name VG_XenStorage-x-x-x-x-408b91acdcae LV UUID x-x-x-x-x-x-vQmZ6C LV Write Access read/write LV Status available # open 0 LV Size 4.00 MiB Current LE 1 Segments 1 Allocation inherit Read ahead sectors auto - currently set to 256 Block device 253:0 root@rescue ~ # vgdisplay --- Volume group --- VG Name VG_XenStorage-x-x-x-x-408b91acdcae System ID Format lvm2 Metadata Areas 1 Metadata Sequence No 4 VG Access read/write VG Status resizable MAX LV 0 Cur LV 1 Open LV 0 Max PV 0 Cur PV 1 Act PV 1 VG Size 698.62 GiB PE Size 4.00 MiB Total PE 178848 Alloc PE / Size 1 / 4.00 MiB Free PE / Size 178847 / 698.62 GiB VG UUID x-x-x-x-x-x-53w0kL I could understand if a full physical volume is lost - but why only the logical volumes? Is there any explanation for this? Is there any way to recover the logical volumes? EDIT We are here in a rescue system. The problem is that the whole server does not boot (GRUB error 22) What we are trying to do is to access the root filesystem. But everything was in the LVM. We have only this: (parted) print Model: ATA SAMSUNG HD753LJ (scsi) Disk /dev/sdb: 750GB Sector size (logical/physical): 512B/512B Partition Table: msdos Number Start End Size Type File system Flags 1 32.3kB 750GB 750GB primary boot, lvm And this 750GB LVM volume is exactly what we see on top.

    Read the article

< Previous Page | 209 210 211 212 213 214 215 216 217 218 219 220  | Next Page >