Search Results

Search found 38126 results on 1526 pages for 'running'.

Page 217/1526 | < Previous Page | 213 214 215 216 217 218 219 220 221 222 223 224  | Next Page >

• INACCESSIBLE_BOOT_DEVICE after installing Linux on same drive

  - by kdgregory

  History: My PC was configured with two drives: an 80G on IDE 0 Primary that was running Win2K, and a 320G on IDE 0 Secondary that was running Linux (Ubuntu). I decided to pull the 80Gb drive out of the system, so dd'd the entire 80 G drive (/dev/sda) onto the 320 (/dev/sdb) -- this included the MBR and partition table. Then I pulled the drive, plugged the 320 into IDE 0 Primary, and rebooted. The Windows partition worked at this point. Then I installed Ubuntu into the remaining space on the 320. It works. However, when I try to boot into Windows, I get a BSOD with the following message: *** STOP: 0x0000007B (0x89055030,0xC000014F,0x00000000,0x00000000) INACCESSILE_BOOT_DEVICE Before the BSOD I see the Win2K splash screen, and it claims to be "starting windows" for a couple of seconds -- so it appears that the first stage boot loader is working as expected. Ditto when I try booting in Safe Mode. After reading the Microsoft KB article, I booted into the recovery console and tried running chkdsk /r. It refused to run, claiming that the drive was corrupted (sorry, didn't write down the exact error message). However, I can mount the drive from Linux, and access all files. And for what it's worth, I can scan the drive using the Linux "Disk Utility" (this is Ubuntu, the menus don't show real program names), it claims the drive to be clean. The KB article mentioned that boot.ini could be the problem, so here it is: timeout=10 default=multi(0)disk(0)rdisk(0)partition(1)\WINDOWS [operating systems] multi(0)disk(0)rdisk(0)partition(1)\WINDOWS="Microsoft Windows 2000 Professional" /fastdetect Any pointers on what to do next?

  Read the article

• Linux Centos 6 becomes unavailable from time to time - OS&network issue

  - by adoado0

  I am encountering following problem. There is one server (DL160 G5) running Centos 6.3 with default kernel 2.6.32-220.2.1.el6.x86_64 - at this point I'd like to add that issue appeared also at older version - 6.1 and older kernel (do not remember exactly which version). There is cPanel installed and from time to time it becomes unavailable (network connection). What I've checked is (via KVMoIP): load average is completely normal it does not lack memory or disk space when problem occurs no console notifications checked all access logs and there is no sign that it can be caused by a client script cannot even access local interface (127.0.0.1) or main IP address running tcpdump I can only see packets arriving to server - no responses all services seem to be running properly (mail,sql,http,ssh) checked crontab and all clients' crontabs too network port utilisation is low ( up to several Mbits) arriving packet rate is low - hundreds per second (according to tcpdump) console (via kvmoip) works fine, no lags there is no conntrack at this server there is no ipv6 at this server flushing iptables, unloading modules does not resolve problem restarting network does not resolve problem, no errors appear it also occurs when two sepearate networks are configured (and multiple gateways) as well as one IP, one default gw and one network is configured - so it seems network configuration independent it seems to repeat randomly (load,packet rate,bandwith usage,load independent) checked server with different rootkit detection tools - it seems to be clean server has been rebooted, it did not change anything there are no interface errors it apperas randomly can be once a week or several times per day It usually works fine after 1-15 minutes. What I can also check? It is definitely OS issue - there is traffic at interface only in one direction when problem occurs, can not even ping loopback. Any ideas? Recommended checks? Anything I did not checked above.

  Read the article

• How do I configure IIS to allow access to network resources for PHP scripts?

  - by Dereleased

  I am currently working on a PHP front-end that joins together a series of applications running on separate servers; many of these applications generate files that I need access to, but these files (for various reasons) reside on their parent servers. If I, from the command line, issue a bit of script such as: <?php var_dump(glob("\\\\machine-name\\some\\share\\*")); I will get the full contents of that directory, proving that there's no problem programmatically with PHP reading the contents of a UNC share. However, if I try to execute the same script from the web server, I get an empty array -- more specifically, if I use more explicitly functions designed to "open" a directory like it was a file, I get access errors. I believe this to be a permissions issue, but I am not a server/network administrator type, so I'm not sure what I need to do to correct this and get my script running, and the links I've checked out have not been a terrible amount of help, perhaps due to my background, or lack thereof as far as IIS is concerned, coupled with the fact that we are not actually using .NET for this. Relevant Stats: Windows Server 2008 Standard SP2 IIS 7.0 PHP 5.2.9 I will be connecting to two types of servers: a few other nearly-identical Server 2008 machines, and a machine running embedded XP. Links that have not been particularly helpful but maybe I am just misreading: http://support.microsoft.com/?id=306158 http://support.microsoft.com/kb/207671/EN-US/ http://support.microsoft.com/kb/280383/

  Read the article

• Terminal Server CPU usage at 100%

  - by Light1c3

  I'm running a terminal server with around 50-60 users,and every so often the server will go from 40% usage to 100%. I took a closer look an it seems every time this happens, a different user or two seem to be caught in a loop and end up using < 30% where the rest of the users only use a maximum of 5%. The company behind the software we use clame it's due to the servers inadequate hardware (It's a VM system running on a dual - quad core setup) which to me sounds like BS! I'm fairly new to this level of IT so if I misspoke I apologize. I have no way to prove it but I believe adding more raw hardware power wont do me any good as this to me seems like a bug in their software, and it will suck up as much ( or little) CPU as it's given. The VM in question has 4 vCPU cores and 12 GB RAM available, and is running Windows Server 2008, 64-bit Thanks in advance for your help! Note: I have the same question posted on SO, but was pointed in this direction so just in case, here is a link to the post http://stackoverflow.com/questions/17276602/termserver-cpu-at-100

  Read the article

• How to automatically start VM created by virt-manager?

  - by Jeff Shattock

  I have created a virtual machine with virt-manager that runs on kvm/qemu. The machine works well when started through virt-manager. However, I would like to be able to start and stop the VM through a script in init.d, so that it comes up and down along with the host. I need to have virt-manager show that the machine is running, and to be able to connect to its console through there. When I use the command line that is produced by running ps -eaf | grep kvm after starting the vm through virt-manager, I get some console messages about redirected character devices, but the machine does start and runs properly. However, I do not get any indication from virt-manager that it has started. How can I modify the command line to get virt-manager to pick up the running VM? Is there anything else about the command line that should change when starting outside of virt-manager? Command line is (slightly reformatted for readability): /usr/bin/kvm -S -M pc-0.12 -enable-kvm -m 512 -smp 1 -name BORON \ -uuid fa7e5fbd-7d8e-43c4-ebd9-1504a4383eb1 \ -chardev socket,id=monitor,path=/var/lib/libvirt/qemu/BORON.monitor,server,nowait \ -monitor chardev:monitor -localtime -boot c \ -drive file=/dev/FS1/BORON,if=ide,index=0,boot=on,format=raw \ -net nic,macaddr=52:54:00:20:0b:fd,vlan=0,name=nic.0 \ -net tap,fd=41,vlan=0,name=tap.0 -chardev pty,id=serial0 -serial chardev:serial0 \ -parallel none -usb -usbdevice tablet -vnc 127.0.0.1:1 -k en-us -vga cirrus

  Read the article

• Recovery disk Windows 8 HP Pavilion g6

  - by fpghost

  I recently purchased a HP Pavilion g6 laptop running Windows 8. I want to either obtain the Windows 8 ISO or make some kind of recovery disk that would allow me to restore the system if things go wrong. The HP Pavilion comes with the 'HP Recovery Manager' which I thought may do the job, but on running it and putting in a DVD-R as requested it seems to just hang for a number of hours without doing a thing (the disk sounds like it's spinning for a few minutes but then goes silent). I then tried 'recdisc.exe' but I get the error System Repair could not be created The device reported unexpected or invalid data for a command. (0xC0AA02FF) Next I obtained my Windows 8 product key using the software ProduKey thinking this would allow me to go to the Microsoft website and download the Windows 8 ISO, but as far as I can tell all that is available is the upgrade which can be used if one is running something like Windows 7. Can anyone advise? EDIT: after a reboot recdisc.exe did work; I think the problem was due to some Windows updates needing a reboot, but never the less I would like a full Windows 8 ISO if possible.

  Read the article

• Replicated filesystem and EC2 MySQL

  - by El Yobo

  I'm currently investigating migrating our infrastructure over to run on Amazon's EC2 and am trying to figure out the best way to set up a MySQL service. I'm leaning towards running our own MySQL instances, rather than going with Amazon's RDS, but am still considering the best approach for performance and cost on the instance itself. In order to have persistent data, the MySQL data needs to be on an EBS volume (with some form of striped RAID, e.g. RAID0 or RAID10) to improve persistence. However, EBS IO is limited by the network interface (gigabit, so a theoretical maximum of 128 MB/s), while the ephemeral volumes have no such problem. I did see a suggestion for running two MySQL servers on an instance, with a master running on the ephemeral disk (which we would also RAID) and a slave storing changes to an EBS volume, but this has some additional overhead and complexity (two servers). What I was imagining is using some form of replicated file system such that I could have a filesystem on top of a RAID0 of ephemeral volumes to maximise performance all changes from the above immediately replicated to another RAID1 volume backed by multiple EBS volumes to ensure no data loss The advantages of this would be best possible IO performance for the DB server; no network delay in IO decreased IO on EBS volumes (as all read IO will be done on the ephemeral volumes) so decreased cost good data security, as it's backed onto redundant EBS volumes However, I haven't seen an appropriate system to replicate all changes from one volume to the other; is there a filesystem, or any other approach, which will do this? The distributed file systems, e.g. GlusterFS, DRBD etc seem to focus on replicating disks between servers, can they be set up to do what I'm interested in here? I also haven't seen anything about other's taking this approach. Do I have a solution in need of a problem here (i.e. is performance good enough, so this whole idea is redundant)? Is there some flaw in the plan?

  Read the article

• How can I ensure that my static ip address is read from /etc/network/interfaces rather than dhcp?

  - by jonderry

  This is a follow up to the following question. I'm trying to set a static IP by changing /etc/network/interfaces to the following: # interfaces(5) file used by ifup(8) and ifdown(8) auto lo iface lo inet loopback auto eth0 iface eth0 inet static address 192.168.2.133 netmask 255.255.255.0 gateway 192.168.2.1 dns-nameservers 8.8.8.8 and then running /sbin/ifdown eth0; /sbin/ifup eth0. However, the change in IP address doesn't appear to take effect without editing /etc/dhcp/dhclient.conf and commenting out the following before running ifdown; ifup: request subnet-mask, broadcast-address, time-offset, routers, domain-name, domain-name-servers, domain-search, host-name, dhcp6.name-servers, dhcp6.domain-search, netbios-name-servers, netbios-scope, interface-mtu, rfc3442-classless-static-routes, ntp-servers, dhcp6.fqdn, dhcp6.sntp-servers; Strangely, after commenting out this line, running ifdown; ifup works, but when I uncomment it, the behavior does not revert to the previous behavior of ignoring changes to my settings in /etc/network/interfaces (this doesn't seem like a problem, but I really need to be able to repeat this problem so that I can be confident that my solution is robust) Also, I'd rather not have to edit /etc/dhcp/dhclient.conf to change my static IP since it seems I should be able to do this by only editing interfaces. Can anyone explain the issues I'm seeing above and suggest the best way of making changes to static IP addresses take effect that admits reproducibility so that I can be sure that my approach works?

  Read the article

• Join Domain from VM

  - by Adis

  I have two VMs running on VMWare Player. I use NAT adapter settings. The host machine for VMs is running on corporate network. First VM has Domain controller running and I can log in on that machine using domain credentials. I named domain wm.local When I run IP config on this machine: IP: 192.168.87.132 Def Gataway: 192.168.87.2 DNS server: 192.168.87.2 DHCP server: 192.168.87.254 Second VM cannot join domain. When I try it with domain WM I'm propmted for credentials. And I enter Administrator credentials and than it waits for some time and I get response: "The specified domain either does not exist or could not be contacted" If i type wm.local as domain when trying to join it does not prompt me to login but just shows "An Active Directory Domain Controller (AD DC) for the domain wm.local could not be contacted. And here it takes no time to get this error message. Ipconfig on this machine: IP: 192.168.87.134 Def Gataway: 192.168.87.2 DNS server: 192.168.87.2 DHCP server: 192.168.87.254 I can ping second VM from first one. And I disabled firewalls on both machines. Any ideas? Is there any manual for this?

  Read the article

• Is my motherboard failing, or is there some other issue?

  - by ThatGuy

  So, several months ago I put together my own desktop PC. I set up a dual boot to Windows and Ubuntu. Recently, without changing any settings or installing anything new, the wifi stopped working on windows (I use a wifi adapter). It said it was connected, Network settings showed that it was working and running trouble shooting had no results. My internet still works on any other device. I found that removing the adapter from the motherboard and plugging it back in was the only thing that fixed the problem. Reinstalling the wifi drivers did not help. I purchased a new Wifi adapter, but the problem persists. More recently, I had a much more discouraging development. Sometimes, turning on the computer results in a boot loop: BIOS never starts. Instead, the monitor turns on as if it got a signal, then immediately turns off. This loops on it's own indefinitely until I hold down power, hard reset it, and try again. Sometimes it works, sometimes it doesn't. I haven't tested much on the Ubuntu side. It appears that wifi works at least some of the time, but since I've had issues just getting to BIOS I'm not confident the issue is on the software side. I've also noticed issues with some of the USB ports no longer working, but that seems to be off and on. Finally, as of a few minutes ago, I booted to windows to discover that everything was running very slowly. Slow here is a relative word, but I have a Samsung 840 pro SSD and I'm used to applications running nigh instantly, and it was a solid 3 minutes before any of my applications would load. Anyway, my question is this: Is it likely that my motherboard is failing? Either way, what steps can I take to try and pin down the problem and figure out what to do?

  Read the article

• Open ports broken from internal network

  - by ksvi

  Quick summary: Forwarded port works from the outside world, but from the internal network using the external IP the connection is refused. This is a simplified situation to make the explanation easier: I have a computer that is running a service on port 12345. This computer has an internal IP 192.168.1.100 and is connected directly to a modem/router which has internal IP 192.168.1.1 and external (public, static) IP 1.2.3.4. (The router is TP-LINK TD-w8960N) I have set up port forwarding (virtual server) at port 12345 to go to port 12345 at 192.168.1.100. If I run telnet 192.168.1.100 12345 from the same computer everything works. But running telnet 1.2.3.4 12345 says connection refused. If I do this on another computer (on the same internal network, connected to the router) the same thing happens. This would seem like the port forwarding is not working. However... If I run a online port checking service on my external IP and the service port it says the port is open and I can see the remote server connecting and immediately closing connection. And using another computer that is connected to the internet using a mobile connection I can also use telnet 1.2.3.4 12345 and I get a working connection. So the port forwarding seems to be working, however using external IP from the internal network doesn't. I have no idea what can be causing this, since another setup very much like this (different router) works for me. I can access a service running on a server from inside the network both through the internal and external IP.

  Read the article

• Scaling a node.js application, nginx as a base server, but varnish or redis for caching?

  - by AntelopeSalad

  I'm not close to being well versed in using nginx or varnish but this is my setup at the moment. I have a node.js server running which is serving either json, html templates, or socket.io events. Then I have nginx running in front of node which is serving all static content (css, js, etc.). At this point I would like to cache both static content and dynamic content to memory. It's to my understanding that varnish can cache static content quite well and it wouldn't require touching my application code. I also think it's capable of caching dynamic content too but there cannot be any cookie headers? I do use redis at the moment for holding session data and planned to use it for other things in the future like keeping track of non-crucial but fun stats. I just have no idea how I should handle caching everything on the site. I think it comes down to these options but there might be more: Throw varnish in front of nginx and let varnish cache static pages, no app code changes. Redis would cache dynamic db calls which would require modifying my app code. Ignore using varnish completely and let redis handle caching everything, then use one of the nginx-redis modules. I'm not sure if this would require a lot of app code changes (for the static files). I'm not having any luck finding benchmarks that compare nginx+varnish vs nginx+redis and I'm too inexperienced to bench it myself (high chances of my configs being awful). I'm basically looking for the solution that would be the most efficient in terms of req/sec and scalable in the future (throw new hardware at the problem + maybe adjust some values in a config = new servers up and running semi-painlessly).

  Read the article

• How to prevent the command prompt from closing after execution?

  - by Sk8erPeter

  My problem is that in Windows, there are command line windows that close immediately after execution. To solve this, I want the default behavior to be that the window is kept open. Normally, this behavior can be avoided with three methods that come to my mind: Putting a pause line after batch programs to prompt the user to press a key before exiting Running these batch files or other command line manipulating tools (even service starting, restarting, etc. with net start xy or anything similar) within cmd.exe(Start - Run - cmd.exe) Running these programs with cmd /k like this: cmd /k myprogram.bat But there are some other cases in which the user: Runs the program the first time and doesn't know that the given program will run in Command Prompt (Windows Command Processor) e.g. when running a shortcut from Start menu (or from somewhere else), OR Finds it a little bit uncomfortable to run cmd.exe all the time and doesn't have the time/opportunity to rewrite the code of these commands everywhere to put a pause after them or avoid exiting explicitly. I've read an article about changing default behavior of cmd.exe when opening it explicitly, with creating an AutoRun entry and manipulating its content in these locations: HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Command Processor\AutoRun HKEY_CURRENT_USER\SOFTWARE\Microsoft\Command Processor\AutoRun (The AutoRun items are _String values_...) I put cmd /d /k as a value of it to give it a try, but this didn't change the behaviour of the stuffs mentioned above at all... It just changed the behaviour of the command line window when opening it explicitly (Start-Run-cmd.exe). So how does it work? Can you give me any ideas to solve this problem?

  Read the article

• Performance-optimizing Oracle 10g on a server that is also a Tomcat JSP app server?

  - by PKHunter

  I have inherited a simple RedHat 5 - 64bit platform. It has SCSI disks on RAID1, with 16GB of RAM. Double Core CPU. Oracle 10g, Release 2. This would be a decent platform for running the DB only, perhaps, but the same server in an "A-A mode" clustering (very simple) also runs Tomcat and there are several Java servlets running on this. Sadly there is no caching platform etc. We only use an external CDN for some html caching. I am personally more familiar with web environments on the LAMPP platform (apache, php, mysql, postgresql). PROBLEM: Because the server has both Tomcat JSP/Java and Oracle 10g running on the same server, with no caching, I have some issues of the server going down. Often, sadly. QUESTION: What are my options in terms of improving performance of all these different apps? Connection Pooling? Example, in Postgresql world we have PgBouncer, which really helps things. Does Oracle have something similar? Or is there a famous Java-based external pooler that people use in production environments? (I'm not familiar with Java) Any "SQL cache" as in the MySQL and Postgresql world? Any other kind of application cache, as "APC" or "eAccelarator" in the PHP world? The "OSCache" stuff from the Java world (JSP thingie I found on Google: http://onjava.com/pub/a/onjava/2005/01/05/jspcache.html?page=2) ... What else? Sorry if this is a noob question. I have googled and googled, but problem is I don't know what to google for, other than the broad general concepts above. So if not full answers, I would even appreciate basic pointers and I am happy to JFGI myself. Thanks!

  Read the article

• 3-4 old computers = general purpose cluster?

  - by TheLQ

  I have 3 old computers lying around right now running a P2 at 800 MHz(?), Intel Mobile 1.6 GHz, AMD Athlon XP 2000+ at 1.66 GHz, and (might not use this) P4 at 2.7 GHz, all with 512 MB Ram, and am considering clustering them together for fun/knowledge. They would be running an undecided version of linux, preferably ubuntu based. The issue is what I want to use it for: general computing and occasional video encoding. By general computing I mean day to day tasks. However I'm not sure if every program started by a single X session is going to exist on the same machine, defeating the purpose of such a system. Will programs be split up or exist on one machine? Second, assuming this is running 100baseT ethernet (not sure if the PCI slot itself could handle Gigabit), would the speed of having a program exist over the network be an issue? It seems that the constant asking of various things in RAM would be quite slow. And before you say "buy another computer!", that's not the point of this question. I'm asking would it be usable, not necessarily practical. And yes I know, this is going to be extreamly power consuming.

  Read the article

• java memory allocation under linux

  - by pstanton

  I'm running 4 java processes with the following command: java -Xmx256m -jar ... and the system has 8Gb memory under fedora 12. however it is apparently going into swap. how can that be if 4 x 256m = 1Gb ? EDIT: also, how can all 8Gb of memory be used with so little memory allocated to basically the only thing running? is it java not garbage collecting because the OS tells it it doesn't need to or what? TOP: top - 20:13:57 up 3:55, 6 users, load average: 1.99, 2.54, 2.67 Tasks: 251 total, 6 running, 245 sleeping, 0 stopped, 0 zombie Cpu(s): 50.1%us, 2.9%sy, 0.0%ni, 45.1%id, 1.1%wa, 0.0%hi, 0.8%si, 0.0%st Mem: 8252304k total, 8195552k used, 56752k free, 34356k buffers Swap: 10354680k total, 74044k used, 10280636k free, 6624148k cached PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND 1948 xxxxxxxx 20 0 1624m 240m 4020 S 96.8 3.0 164:33.75 java 1927 xxxxxxxx 20 0 139m 31m 27m R 91.8 0.4 38:34.55 postgres 1929 xxxxxxxx 20 0 1624m 200m 3984 S 86.2 2.5 183:24.88 java 1969 xxxxxxxx 20 0 1624m 292m 3984 S 65.6 3.6 154:06.76 java 1987 xxxxxxxx 20 0 137m 29m 27m R 28.5 0.4 75:49.82 postgres 1581 root 20 0 159m 18m 4712 S 22.5 0.2 52:42.54 Xorg 2411 xxxxxxxx 20 0 309m 9748 4544 S 20.9 0.1 45:05.08 gnome-system-mo 1947 xxxxxxxx 20 0 137m 28m 27m S 13.3 0.4 44:46.04 postgres 1772 xxxxxxxx 20 0 135m 25m 25m S 4.0 0.3 1:09.14 postgres 1966 xxxxxxxx 20 0 137m 29m 27m S 3.0 0.4 64:27.09 postgres 1773 xxxxxxxx 20 0 135m 732 624 S 1.0 0.0 0:24.86 postgres 2464 xxxxxxxx 20 0 15028 1156 744 R 0.7 0.0 0:49.14 top 344 root 15 -5 0 0 0 S 0.3 0.0 0:02.26 kdmflush 1 root 20 0 4124 620 524 S 0.0 0.0 0:00.88 init 2 root 15 -5 0 0 0 S 0.0 0.0 0:00.00 kthreadd 3 root RT -5 0 0 0 S 0.0 0.0 0:00.00 migration/0 4 root 15 -5 0 0 0 S 0.0 0.0 0:00.04 ksoftirqd/0

  Read the article

• Migrate active directory to Google apps for business

  - by dewnix

  I've got a problem migrating active directory to Gapps. I'm stuck on google apps directory sync (GADS) where it just gives the error "java.lang.NullPointerException" after testing the connection during the LDAP configuration step. I checked the logs and I've pretty much determined that port 389 (standard LDAP port) isn't listening on the exchange server. I've tried telneting to it (from another machine in the same network) with no luck but I can telnet to other ports, that i know are open, successfully. I know they're open because I used portqry and netstat to see them. I'm suspecting that the active directory isn't even installed/running on this machine because there's no active directory services at all running on it. There's no active directory services that say they're NOT running either though. Is it possible AD is installed somewhere else? does it have to be on a machine inside the same network? I found the domain controller and it's host name and when I telnet with port 389, it works however GADS still gives me the same exact error when I substitute that server in. Actually, no matter what ridiculous settings i put into GADS, i still get that same NullPointer error. If i could get some different error than that NullPointer, i'd call that a successful day.

  Read the article

• Identifying Exchange 2010 regular process that is walking the mailbox database

  - by toongeneral

  I have an Exchange 2010 server running on a SAN-backed platform. The platform does block-level backups based on a snapshot/incremental basis, that only capture changed data. I was surprised to see a regular period of time where the data changes were happening at a high, sustained rate. Due to the way this system works, that can lead to 1.2TB of stored data per month. The regularity implied a scheduled task, but it is not a fixed interval. It is approximately every 26-32hrs. The disks were performing read operations of ~5MB/s and write operations of ~4.5MB/s, for a period of 3-4hrs. The total written data was ~55-60GB. Reading on TechNet, I am wondering if the following is causing this: http://blogs.technet.com/b/exchange/archive/2011/12/14/database-maintenance-in-exchange-2010.aspx#checksumming The somewhat restrictive thing is that the process only happens at most once every 24 hours. I was able to investigate while it was running, finding the following: the process is store.exe it is working on the mailbox database files while running, it is generating .log files (in the mailbox database folder) consistent with database changes the mailbox database is ~60GB in size, which fits with the total data changes on each iteration I have currently switched to a fixed maintenance window, as a test. It's not clear whether this is the cause, as the symptoms fit, but are not conclusive. Does anyone have any suggestions for additional troubleshooting?

  Read the article

• What are secure ways of sharing a server (ssh+LAMP) with friends?

  - by Bran the Blessed

  What is the best way to share a virtual server with friends? More precisely, I have the following assets: A virtual private server (Debian Lenny) with root access for myself, running... SSH apache2 mysql Some unused disk space Some friends in need of hosting The problem I would now like to do the following: Hosting one or several domains per friend My friends should have full access to their domains, including running PHP scripts, for example My friends should not be able to poke around in other directories The security of my server should not be compromised by faulty PHP scripts To clarify: I do trust my friends in the sense that they are not trying to do something evil with their access. I just do not trust the programs they are going to run. So, what are your recommendations for establishing such a scenario? Partial solution I already came up with the following plan: Add chrooted SSH users for my friends Add Apache vhosts per user (point the directories to subdirectories of the homedirectories, i.e. /home/alice/example.com, /home/bob/example.net, etc. But how can I enforce a chroot-like environment for the scripts they are running within these vhosts? Any pointers would be appreciated.

  Read the article

• Windows Server 2008 Alerting to Low memory

  - by t1nt1n

  I have a file and print server running on Windows 2008 R2 fully patched in a VSphere environment (ESXi 5.1 fully updated). Every evening between 19:20 and 19:30 our monitoring software reported that the available memory is 1% and performance is dire. There is nothing in the event logs to point to an issue. At this point in the evening I am general the only user on the system to check to see why these alerts are going off. Things I have done; Checked to see if any backups are running – None at all. Checked Scheduled tasks – None before or during this time period. Moved the VM to another host. AV is disabled to rule out that as the issue. The server does not have any problems during the day with memory when fully loaded with about 50 users. The server did have 4GB ram provisioned but I have increased this to 5Gb. Running PrefMon at the time (I will save the graphs tonight) There very little CPU usage at the time but RAM usage goes up.

  Read the article

• Python 2.7 and Ubuntu 10.10: X11 fails

  - by c.a.p.

  Against every recommendation I have apt-get remove python in Ubuntu 10.10 (build 2.6.24-29-server x86_64) and apt-get install python2.7 Some built-in software with python2.6 dependencies (like firefox, other minor stuff) was fixed just by apt-get reinstalling or reinstalling from source and the system was stable for one day until I rebooted. Upon booting I got the message "ubuntu is running in low-graphics mode" I have an NVIDIA Quadro NVS 295 256 running on a HP Z600 Workstation so I sudoed: apt-get --purged nvidia* apt-get --purged xserver apt-get install linux-headers-generic apt-get install nvidia-* apt-get install xserver-xorg dpkg-reconfigure xserver-xorg nvidia-xconfig upon rebooting i get the same "ubuntu is running in low-graphics mode" if I decide to tell the boot menu to restart X, the Ubuntu 10.10 "load screen" shows up and does not do anything for hours. If I "X" the screen remains black for hours; ctrl-c shows that /etc/X11/xorg.conf did not produce any errors just a warning "Type "ONE_LEVEL"...". /var/log/Xorg.0.log issues the following warnings (no errors) (WW) AllowEmptyInput is on (WW) NVIDIA(0): UBB is incompatible If I "startX" I get /usr/bin/python: can't find '__main__.py"' in '/usr/share/command-not-found' Before re-installing xserver-xorg however "startX" ran, just by changing the resolution of the tty1 console. Any hints?

  Read the article

• Inexpensive (used) hardware for Xen virtualization test?

  - by Jason Antman

  Virtualization is one of the areas where I could really use some experience. I also run quite a few services (web, mail, dns, etc.) out of my home. Since most of my hardware is getting a bit old (I'm running on stuff that was surplused years ago...) I decided that it's about time I start renewing some things, and also play around with virtualization a bit more. My plan is to setup a SAN box (simple iSCSI target, relatively inexpensive gigE switch), get a pair (for starters) of new servers, and start building some new stuff with Xen, specifically planning on playing with live migration and full virtualization. Does anyone have recommendations for used, older "servers" (really anything in a rack-mount form factor, I'm not too worried about things like iLO/iLOM for the test nodes) that support VT-x/AMD-V? I'm biased to HP, but it looks like they didn't make Proliants with VT-x/Vanderpool processors until G6 (for the DL360) or so, which is way out of my price range. I'm looking in the sub-$300 range (or less, if possible), used, probably Ebay. Any recommendations are greatly appreciated. Edit:And, to catch this before the comments start coming - these are personal systems. I have first-generation Proliants still in use (I got them as corporate surplus in 05, they've been running since then, and probably were running since 01 or 02 prior to being sold). I don't need anything shiny and new - I've got a bunch of old boxes, at least one complete replacement for every model in use, and that's fine for me (and easy on the wallet).

  Read the article

• Building a small server farm

  - by RayQuang

  Hi, I am planning to set up a Tech startup company that will provide web application solutions. Eventually we hope to diversify into different areas such as possibly social media or other services. For now we plan on running a high demand (from 1000 to 10,000 users in the first year) website running the application. This includes a MySQL database backend, email, and development servers. My question is then, what type of server arrangement will work best, that is ti say should i have a small cluster of ultra high power machines (E.G. Top of the range Xeons, with 12GB RAM) or will it be better to have more less powerful servers load balanced? Should I go for 1 - 2 u servers rack mounted ot would it be beter for it just to be tower servers for maintainability? Finally I would also like to know what kind of Internet and router i would need, I currently have 10mbit down and barely 1 mbit up, but soon our area will have a fiber optic connection with international speeds of up to 25 mbit / sec. Thanks in advance, RayQuang UPDATE: sorry I forgot to mention it, the platform that I will be using is PHP with the APC code cache, Probably running Debian.

  Read the article

• How much Ram should I need on my VPS package? Am I being ripped off?

  - by Tamerax

  Hello! So, I'm currently on a VPSVille Cpanel3 account that has 768 MB guaranteed ram and 2048 MB burst ram (full details here: http://www.vpsville.ca/cpanel-vps). It's running CentOS, Cpanel, Apache and FastCGI. On the server itself I have a joomla community site with a forum system that generally has about 20 people on it max at any point and even then, during the evening, no one. It's a pretty small site but has a number of modules running on it. It gets about 6000 visits a month. Also on the server is a wordpress site that gets about 80-150 visits a day, 2 other wordpress sites that aren't developed yet so they don't get any traffic at all and 2 static html websites that also only get about 500 hits a month. All in all, no huge sites. The issue is that I get "out of memory" errors fairly frequently and it kills my server and I need to reboot it in order to get all my sites up and running again. It seems to me that I shouldn't have these issues with that much ram allotted to my account and everytime I send in a support ticket, they just tell me to upgrade the ram. Now, I'm still pretty new to all this so I'm not a good judge of how much I really need for my sites to run. I don't know if my sites really do need this much OR vpsville has oversold there servers, they don't actually have those resources available and I'm getting ripped off. So, how much ram should I be using with my current setup? Thanks!

  Read the article

• How do I install MySQLdb on a Python 2.6 source build, on Debian Lenny?

  - by nbolton

  I've installed Python 2.6 from source on my Debian Lenny server, as Lenny does not have the python2.6 package. So, my Python 2.5 has MySQLdb installed and working just fine because I installed the python-mysqldb package. I figured I could just install MySQLdb from source, but because I have the Lenny python-dev package, it builds against 2.5: # python setup.py build running build running build_py copying MySQLdb/release.py -> build/lib.linux-x86_64-2.5/MySQLdb running build_ext building '_mysql' extension gcc -pthread -fno-strict-aliasing -DNDEBUG -g -fwrapv -O2 -Wall -Wstrict-prototypes -fPIC -Dversion_info=(1,2,3,'final',0) -D__version__=1.2.3 -I/usr/include/mysql -I/usr/include/python2.5 -c _mysql.c -o build/temp.linux-x86_64-2.5/_mysql.o -DBIG_JOINS=1 -fPIC gcc -pthread -shared -Wl,-O1 -Wl,-Bsymbolic-functions build/temp.linux-x86_64-2.5/_mysql.o -L/usr/lib/mysql -lmysqlclient_r -o build/lib.linux-x86_64-2.5/_mysql.so I don't want to run python setup.py install, because I'm afraid it's going to screw up MySQLdb on 2.5 -- should I? I imagine it'd just overwrite 2.5 and do nothing to 2.6 -- maybe there's an argument I can use to install to 2.6? I imagine that I would need also to build against 2.6, so how do I do this?

  Read the article

< Previous Page | 213 214 215 216 217 218 219 220 221 222 223 224  | Next Page >